Upload
duongdan
View
219
Download
2
Embed Size (px)
Citation preview
2
pag. 4-17
pag. 18-22
pag. 23-26
pag. 27-32
pag. 33-37
pag. 38-46
pag. 57-61
pag. 50-52
pag. 47-49
pag. 53-56
pag. 63-65
-Electric Mobility.
-PV Devices.
-PV Structures.
-Water Treatment Products.
-Water Pumps and Generators.
-PV products.
-Public Lighting
-Geothermal Products.
-Wind Power products
-Biomass Products.
-Cleantech Incubator powered by Restart Italia.
INDEX ER International Catalog
3
ELECTRIC MOBILITY
4
RANGE EXTENDED
FULL ELECTRIC
BI-MODALE
FE
RE
BM
Focused on innovation, I’M Green vehicles is a company which supplys 100% electric vehicles and charging stations.Full electric, Range Extended and Bi-Modal vehicles are the vehicles that the company I’M Green Vehicles provides.
IM GREEN VEHICLES COMPANY PRESENTATION
5
Jolly 2000, Bruxelles Airport
BM
BI-MODAL Kit Presentation
The Bi-Modal technology is a system that is installed on vehicles by the I’M Green Vehicles technicians. With a rear-wheel drive vehicle which has an internal combustion engine placed on the front, the Bi-Modal kit will be insatlled by:- Keeping the original internal combustion engine without removing it.- Installing an electric engine which will allow the user to drive on a emission free base and when needed by using the internal combustion engine.- A small battery pack will be installed which will allow the user to drive for 50/60km with the Full electric engine. The Bimodal Kit can be installed on any vehicle on the market. This process will allow the user to have a divalent product, usefull for long journeys and for restricted traffic limitation areas where vehicles with the only internal combustion engine cannot drive.- OPTIONAL: It is possible to apply a new internal combustion engine which will make sure that the batteries will be recharged during the journey without using completly the full electric engine.
6
Ducato Minibus per Comune Sant’Agata di Puglia
FEThe Full Electric kit will allow the user to ride around 100-120 km using just the electric engine without the need of a internal combustion engine.- The Full Electric kit can be disassembled and assem-bled on another vehicle if needed, in case if the previous vehicle with the Full Electric kit has reached it’s life.- Using an electric vehicle reduces car speed accidents by 80%.- The user of an electric vehicle has the advantage to save up to 50% on car insurance. The vehicle work maintenace is reduced up to 70%.- The Full Electric Kit gets rid of CO2 emissions like PM10 and PM2,5 in the atmosphere.- The Full Electric vehicles get rid of noise pollution.
Full Electric Kit Presentation
7
Range Extended Vehi-cles are vehicles withboth electric and nter-nal combustion engine which can be powered by diesel or gasoline. The internal combu-stion engine is only used when the lithium battery, which runs theee electric engine,needs to be charged.These vehicles are electric vehicles and the heat engine has the only function to extend the mile or kilometre range of the vehicle. The range can be for around 100km or simply just 10km. In reality, for a full charge, a lot of gasoline is not needed ; it is also pos-
V2G stands for Vehicle to Grid Technology, best known as techno-logy from the vehicle to the network.This technology allows to connect the vehicle to the house ‘s electri-city grid and use the vehicle’s electricity for appliances. With a spe-cific software, this system can become a powerbank for the house, reducing energy consumption and keeping the house bill low. It can also be very usefull in case of a black out. This system transforms the vehicle into an electrical generator even when we are away from home.
sible to use a mixes of bioethanol. This method of recharging he batteries “on board” allows the user to use the vehicle for very long journeys which today is something not possible to do on a pure electric vehicle, and alsobecause of the lack of electric charging stations which are needed not only on normal circumstances but also in emercency.
8
1100kg
123cm x 182cm x 190cmLunghezza max 210cm
Full Electric4W8,3kW4kWh Lib18%
70km (gel)110km (litio)
45km/h
FERE
LOGO VERSIONS
SMILE Data Sheet
The vehicle “Smile” is a minicar and it’s the smallest vehcile of the I’M green Vehicles range. Although Its size the vehicle has a big compartment, easy to access, thanks to Its back boot.
SMILEThe electric Minicar
MINI SMILE Version
SMILE Interiors
Vehicle Type Quadricycle Minicar
Slope max
Speed max
Battery Pack
Dimensions
Engine
Range FE
Weight
PowerMaximum Power
Front BreaksTambourBack BreaksDisk
9
183cm183cm 185cm
minicarconcept
SMART SMILE Description
Smart Smile is the new version of the Mini Smile. It is a fully electric lightweight minicar which has been subjected to a partial restyling. The bumper has been modified to give it a more aggressive appearance to appeal to young people, while a boot has been introduced at the rear of the vehicle.
SMART SMILE DIMENSIONS
Lights View
Logo
Boot View
Dimensions View
Perspective View
10
n°3 Smile per KOMOP, CroaziaN° 1 Smile per l’AMIAT di Torino
n° 2 Smile per Parco Nazionale della SELVA BOEMA n° 27 Smile per Progetto MI MUOVO ELETTRICO-FREE CARBON CITY Emilia Romagna
MINI SMILE
FERE
Mini Smile Dimensions:
x 123cm x 122cm x 193cm
DATI Sheet
Weight: 180kg
Mini Smile is a shorter version of the Smile.
11
FEREN1
2160kg245cm x 156cm x 228cm
Full Electric19KW28kW96V18%
120km (litio)80km/h
The Ecomile vehicle is a van with many cargo systems. It can travel on urban and suburban roads. The vehicle is equipped with a Full Electric or a Range Extended kit.
ECOMILEThe Working Vehicle
LOGO VERSIONS
ECOMILEWith Out CARGO BED
ECOMILE Interiors
ECOMILE Data Sheet
Vehicle Type
Slope max
Speed max
Engine
Battery Pack
Dimensions
Range FE
Power
Weight
Front BreaksTambourBack BreaksDisk
Maximum Power
12
FE
La nuova frontieradell’ibrido.
kit di trasformazione bimodale per minbus
con i kit di trasformazionehai un veicolo ibrido allo stessoprezzo e con la stessa autonomiadi un veicolo a diesel tradizionale.
BI MODE
La tecnologia BI’MODE sfrutta tutte le opportunità ed i vantaggi dell’ibrido parallelo in termini di efficienza ed autonomia offrendo l’opportunità di avere un veicolo in grado di accedere ai centri storici ed alle zone a traffico limitato delle città. La tecnologia BI’MODE è applicabile ad ogni veicolo destinato alla logistica delle merci o al trasporto delle persone. La gamma dei veicoli BI’MODE offre soluzioni efficaci ed efficienti per qualunque tipo di business.
Il pannello di controllo del BI’MODE può essere installato sia in un nuovo sistema da affiancare al tradizionale computer di bordo ma può anche essere integrato a quest’utlimo grazie ad un software di gestione dedicato
Decidi tu quale energia utilizzare.
Iveco DAILY 60 kW
Gruppo accumulatori
Numero 72
Tipo Litio-Polimeri
Capacità 150 Ah/h
Posizione Retro autista
Prestazioni
Velocità max 80 km/h
Pendenza max 18 %
Tempo di ricarica 6/8 ore
Autonomia 100 km
Motore
Posizione Centrale
Funzionamento Asincrono AC
Potenza nominale 30 kW
Potenza effettiva 60 Kw
Regime 2500-5000 rpm
Coppia max 260 Nm
Inverter 270 V 350 A
Tensione nominale 12 V
Converter DC/DC CP3 6000W
Regime 2500-5000rpm
M3
80km/h
80km/h
N1
18%
18%
150Ah/h
8kWh
6/8 ore
4/6 ore
100km *
50km *
Coppia max 260Nm
Potenza nominale 30kW
15kW
Inverter In270 V 350 A
In270 V 350 A
Potenza effettiva 60Kw
30Kw
Tensione nominale 12 V
12 V
Converter DC/DC CP3 6000W
CP3 6000W
BM
BM
FE
FE
RE
RE
RE
Inverter
Converter DC/DC
IVECO DAILY BI-MODAL Data SheetKIT BI-MODAL
FIAT DOBLO’ BI-MODAL BI-MODAL KIT
FIAT DOBLO’ BI-MODE TECHNICAL DATA
TECHNICAL DATA
ENGINE
ENGINE
PERFORMANCE
PERFORMANCE
With the Bi-modal kit
it is possible to have a
hybrid vehicle, equipped with both electric
and combution engine,
at the same price and km
range of a tra-ditional diesel engine vehicle.
The internal combustion
ngine, will be used only when
necessary.
The hybrid version allows the user to have a completly indipendent vehicle when driving outside the city and in ristricted traffic areas. When entering a restricted traffic area it is possible to switch from the internal combustion engine to the full electric engine using the SWITCH comand o the vehicle control panel.
* Possibility to Increase the range.
* Possibility to Increase the range.
Vehicle Type
Vehicle Type
Slope max
Slope max
Speed max
Speed max
Power
Capacity
Capacity
Battery Type
Battery Type
Charging Time
Charging Time
Maximum Power
Range FE
Range FE
Tension
FE + Comb.engine
Power
Tension
Maximum Power
Lithium Battery
13
N1
M3
18%
18%
BIMODE
80km/h
80km/h
30W
60kW
4 ore
4/6 ore
60W
90kW
400kg50 Km *
50/60 Km *
70 Km
600 Km
20Wh a litio
27kWh10/204500/6100 Kg
FE
FE
RE
BM
FERE
The Range extender technology has the same advantages of a Hybridvehicle in efficency terms but only using a Full electric vehicle.
The hybrid version allows the user to have a completly indipendent vehicle when driving outside the city and in ristricted traffic areas. When entering a restricted traffic area it is possible to switch from the internal combu-stion engine to the full electric engine using the SWITCH comand o the vehicle control panel.
FIAT MINIBUS DUCATO BI-MODALBI-MODAL KIT
500 FULL ELECTRIC DATA SHEETFULL ELECTRIC/RANGE EXTENDED KIT
* Possibility to Increase the range.
* Possibility to Increase the range.
TECHNICAL DATA
TECHNICAL DATA
PERFORMANCE
PERFORMANCE
Vehicle Type
Vehicle Type
Slope max
Slope max
Seats
Electric Engine
Electric Engine
Speed max
Speed max
Power
Power
Charging Time
Charging Time
Maximum Power
Maximum Power
Range Full Electric
Range Full Electric
Battery Pack
Battery Pack
Hybrid Range
Hybrid Range
Weight
Weight
Alternating current three-phaseasynchronous
14
M3
18%
Full Electric
80km/h
60kW
4/6 ore
90kW
90/120 Km *
27kWh10/204500/6100 Kg
BM
FE
FE
RE
N° 22 Jolly per Medi Ambient, Barcellona
N° 1 Jolly 2000 per Aereoporto BruxellesN° 1 Jolly per AMSA, Milano
* Possibility to Increase the range.
TECHNICAL DATA
PERFORMANCE
MERCEDES SPRINT.FULL ELECTRIC KIT
I’M Green Vehicles company works.
Vehicle Type
Slope max
Electric Engine
Speed max
Power
Charging Time
Maximum Power
Range Full Electric
Battery PackSeatsWeight
15
398mm x 1295mm x 277mm
120-230V
120-230 Vac
44Kg
50Hz
16A
40A
IP65
CHARGING PLUG
The charging Pointis a product whichallows the user torecharge an electricvehicle. This deviceis not meant for any
other purpose.
The charging point structure is made of stainless steel and plexiglass. The structure is resistant and electricaly insulated. The elec-tronic wiring is protected by an IP65 container which garantees protection rom rain and any other atmospheric agent so that the item can be installed outside.
CHARGING POINT
Door Closed View
The fundamental com-ponents for the correctoperation of the Char-ging Point.
1- Two SCAME PLUGS for charging thevehicle.
2- The comand that unhooks the chargingpoint from electricity in case o emergency.
3- The led light which warns that the chargingpoint is supplying elec-tricity.
4-OPTIONAL: A display panel for the visuali-zation of the charging point status.
TECHNICAL DATA
Frequency
Corrent
Case Protection
Dimensions
Weight
Work tension
Tension supplyCurrentsupplyMaximum Current
Socket Type 2P+T+1AUX
Single phase
16
N° 26 Ecomile per l’AMA di Roma
n°1 Ducato Minibus per Comune Sant’Agata di Puglia
N° 6 Ecomile per Medi Ambient, Barcellona
I’M Green Vehicles company works.
17
I HOME is a company operating in the Energy efficiency sector tank to the production and the selling of storage systems. The company mission is to combine the storage and the domotic techno-logy with a focus on home electric systems and on the home consumption.
I-HOME Company Presentation
PVDevices
18
INFINITY 500
OUTPUT
210x150x53 mm; 1.5 kg1155x29x26 mm; 1.6 kg
120Wh-12V / 10Ah
28W
3-4h
1x 5V/ 2.1A (USB)1x 12V/ 5A (DC)1x 220V/90W (AC)
GPSCellular PhoneSmartphoneLed LightEco Save BulbHI-FINotebookFreezerFridgeComputerTape RecorderTelevisionClassic Light Bulb
77101.520304050507080100100
171712806432.42.41.71.51.31.3
DEVICES WATTS HOURS
1
1
2
2
28Pannello Fotovoltaicopieghevole
CONVERTITORE AC/AC220/110V
ER BULBSKit 5 Lampade 12V - 3W/cad con accensioni separate
KIT
120
50
DIMENSIONS AND WEIGHT
DATASHEET
Sockets
Pannel capacity
Battery capacity
BatteryPannel
Charging Time
BATTERY DURABILITY AND CHARGING DEVICES
Using electric current with the appropriate power supply which comes together with the INFINITY 120.
Threw the solar panel 28.
How To Use Your INFINITY
Available also the Infinity 50Wh
Dimensions (mm) 120x75x20Weight (kg) 0,350InputMicro USB 5 Vdc - 1000 mA MaxOutputUSB output 5 Vdc - 1000 mA MaxUSB output 5 Vdc - 2100 mA Max
Internal ComponentsBattery Li-IonBattery capacity 50 Wh - 13000 mAhLifetime (n° di cicli) Approx. 800-1000Class IIICharging Time ~10 h
19
INFINITY 500
OPTIONAL
1
1
2
2GPSCellular PhoneSmartphoneLed LightEco Save BulbHI-FINotebookFreezerFridgeComputerTape RecorderTelevisionClassic Light Bulb
77101.520304050507080100100
72725033425171210107755
255x210x235 mm; 9.2 kg992x850x36 mm; 11 kg
512 Wh-40V / 12.8 Ah
120W
3h
DEVICES WATTS HOURS
350
CONVERTITORE AC/DC220V/ 110V
OUTPUT
2x 12V/ 5A (DC)1x 12V/ 7A2x 5V/ 2.1A (USB)2x 220V/ 300W (AC)
INFINITY 500 is planned to supply electric current to stands, isolated cabins, gazebo and can light the environment and recharge many electric devices like tv, notebook, tablet and many more.
Available also the Infinity 350 lead gel with 350 Wh
120Solar Panel
CONFURTABLE BAGto carry the ER 500
ER BULBSKit 5 Lamps 12V-3W/cad
BATTERY DURABILITY AND CHARGING DEVICES
SOLAR POWER STATION
THE ENERGY YOU NEED
Using electric current with the appropriate power supply which comes together with the INFINITY 500.Threw the solar panel 120.
DIMENSIONS AND WEIGHT
DATASHEET
Sockets
Pannel capacity
Battery capacity
BatteryPannel
Charging Time
How To Use Your INFINITY
20
Vista Storage con Modulo FV Pieghevole
Vista ampia componenti elettrici
Vista uscite USB e 12V Vista Interruttori
Display di controlloConnettori fotovoltaici e uscita 220V
Visual E-Box Parts
Vista Storage con Modulo FV Pieghevole
Vista ampia componenti elettrici
Vista uscite USB e 12V Vista Interruttori
Display di controlloConnettori fotovoltaici e uscita 220V
Visual E-Box Parts
Vista Storage con Modulo FV Pieghevole
Vista ampia componenti elettrici
Vista uscite USB e 12V Vista Interruttori
Display di controlloConnettori fotovoltaici e uscita 220V
Visual E-Box Parts
E-BOX
OUTPUT
350x210x235 mm; 25 kg1200x850x36 mm; 3 kg
1kW
750W
4hIP66
GPSCellular PhoneSmartphoneLed LightEco Save BulbHI-FINotebookFreezerFridgeComputerTape RecorderTelevisionClassic Light Bulb
77101.520304050507080100100
140140100512503224202014141010
DEVICES WATTS HOURS
Vista Storage con Modulo FV Pieghevole
Vista ampia componenti elettrici
Vista uscite USB e 12V Vista Interruttori
Display di controlloConnettori fotovoltaici e uscita 220V
Visual E-Box Parts
Vista Storage con Modulo FV Pieghevole
Vista ampia componenti elettrici
Vista uscite USB e 12V Vista Interruttori
Display di controlloConnettori fotovoltaici e uscita 220V
Visual E-Box Parts
1kW
1kW
1
2 3
4 5
OPTIONAL
E-BOX is a storage system that allows you to accumulate the energy deriving it from PV panels. This energy can be used to recharge the home electric devices (es. TV, appliances, lights, ecc). Smartphone, tablets and other devices can be reload thanks to the USB connectors. The system is an IP66 storage and is planned on a trolley.
BATTERY DURABILITY AND CHARGING DEVICES
DIMENSIONS AND WEIGHT
DATASHEET
Sockets
Pannel capacity
Battery capacity
BatteryPannel
Charging TimeSorage
2x photovoltaic plugs1x 24V/ 7A2x 5V/ 2.1A (USB)2x 220V/ 300W (AC)
1-Display Rasberry view.2-24V e USB socket view.3-Switch view.4-220 V and PV sockets view.5-Ebox with panel.
HOW TO USE THE E-BOX
21
7.5W; 310x195x19mm; 0.6Kg
9W; 270x270x18mm; 0.6Kg
200 lumen-5 h
100% 300 lumen- 3h50% 150 lumen- 6h10% 30 lumen- 30h
4-5 h
4-5 h
ER LIGHT can light small flats, gazebo, sheds (cabins) stalls, vinery vans, closets, thanks to the sun. During the day you reload the lamps and you have the light in the night.
There are two light points, manageable by remo-te control. It has the ability to adjust the light intensity in three different degrees depending on the actual needs. This allows to better observe the battery. Thanks to the USB adapters, ER LIGHT can also recharge your smartphone.
The kit includes:-Photovoltaic panel;-2 LED bulbs with built-in batteries, shutdown button, hook;-Multiplug Connector;-3 Cables 5mt with snap connectors;-Remote control;-Adattatore USB power strip for portable de-vices;-2 fairleads for su-spension lamps;
SOLAR LIGHT KIT +2 LED Lamps 3W+ USB Cable
SOLAR LIGHT KIT3 LED Lamps 1.8W
ER-LIGHT DATASHEET
ER LIGHT + DATASHEET
Solar Panel
Solar Panel
3 LED 1.8W lamps each.
3 LED 1.8W lamps each.
1 Integrated lithium Battery 2600mAh each
1 Integrated lithium Battery 2600mAh each
Lamps
Lamps
Battery
Battery
Light Intensity
Light Intensity
Charging Time
Charging Time
22
Tempo di ricarica
PVStructures
23
SOLAR GENERATORCONTAINER DA 100 kWh
INVERTER
Max Power 20kW Total Energy 100kWhMax Voltage Input 1000Vcc Battery Batteries with no maintenanceOpen Circuit Voltage 2V
Voltage Range 300-800 Vcc
Battery
MPPT Cell Capacity 250AhTemperature Range -20+60°C Cicles 100%80%50% 1.700/2.100/3.300
Container Standard Alley container 20?, IP67Performance 98% Plugn’Play All the electronics are ready to use
The power station is already installed and ready to use, with two three-phase 400 VAC electrical outlets. Thanks to the snap in – mounting, both of the external structure of the solar panels, ER GENERATOR can be installed in a short time.The generator provides 100 kWh of energy storage through prewired tubular batteries with electrolyte gel, to reach up to 24 hours. It can generate high peak power up to 40 kW, for total energy autonomy in avery area of the world. Thanks to a double set of photovoltaic inverters, high efficiency polycrystalline panels, container IP67 and OPZV batteries (with more than 3.000 charge and discharge cycles), it is possible to reach ten years of use without any need for maintenance, making only simple control opera-tions and cleaning.
STORAGE
PV STRUCTURE
Power 20kW
Polycristalline PV 90 polycristalline 240W panels for a total of 21,6kW peak power
Output 400 Vac 50/60 Hz
Structure 6 alluminium structures 5 x 5m with steel joints
Connectors Standard fast MC4/Tyco with rail connection
Daily Output 100kWh
24
ACCESSORI: CONTROSOFFITTOIN LAMIERA VERNICIATA
- Protezione cablaggi- Perfetta tenuta all’acqua piovana
ACCESSORIPANNELLI RIGIDI PUBBLICITARI
Staffa di ancoraggioper cemento armato
Staffa di ancoraggioda n. 2 picchetti cad.per terreni compatti
Staffa di ancoraggioda n. 4 picchetti cad.per terreni compatti
Staffa di ancoraggioda n. 6 picchetti cad.per terreni compatti
DETTAGLI TECNICI
DETTAGLI TECNICI
DETTAGLI TECNICI
DETTAGLI TECNICI
ACCESSORI: CONTROSOFFITTOIN LAMIERA VERNICIATA
- Protezione cablaggi- Perfetta tenuta all’acqua piovana
ACCESSORIPANNELLI RIGIDI PUBBLICITARI
Staffa di ancoraggioper cemento armato
Staffa di ancoraggioda n. 2 picchetti cad.per terreni compatti
Staffa di ancoraggioda n. 4 picchetti cad.per terreni compatti
Staffa di ancoraggioda n. 6 picchetti cad.per terreni compatti
ACCESSORI: CONTROSOFFITTOIN LAMIERA VERNICIATA
- Protezione cablaggi- Perfetta tenuta all’acqua piovana
ACCESSORIPANNELLI RIGIDI PUBBLICITARI
Staffa di ancoraggioper cemento armato
Staffa di ancoraggioda n. 2 picchetti cad.per terreni compatti
Staffa di ancoraggioda n. 4 picchetti cad.per terreni compatti
Staffa di ancoraggioda n. 6 picchetti cad.per terreni compatti
ACCESSORI: CONTROSOFFITTOIN LAMIERA VERNICIATA
- Protezione cablaggi- Perfetta tenuta all’acqua piovana
ACCESSORIPANNELLI RIGIDI PUBBLICITARI
Staffa di ancoraggioper cemento armato
Staffa di ancoraggioda n. 2 picchetti cad.per terreni compatti
Staffa di ancoraggioda n. 4 picchetti cad.per terreni compatti
Staffa di ancoraggioda n. 6 picchetti cad.per terreni compatti
Giulio Barbieri S.r.l.www.giuliobarbieri.it
Via Ferrara, 41 44028 Poggio Renatico (FE) - Italy
[email protected]. (+39) 0532 821511 Fax (+39) 0532 821555
-The structure supports any PV panel size;-On requests, the solar carport can be equipped with a gutter;-The cover is modular and is suitable for parking of any size;-The asset allows a perfect balance and high resistances to the stresses caused by snow and wind. Warranty: 15 years.-The structures is composed of pro-files in silver anodized aluminum and stainless steel joints.
A solar carport structure can cover many parking spots until the max length of 600 cm.In these imagines you can see many versions, where it is shown the number of photovoltaic panels that can be installed in a horizontal orientation.
The structure has successfully passed the load test in which it was subjected, reacting to the maximum load required by the static calculations with no perma-nent deformation. Each beam weighed for four day two 200 Kg weigh, exerting maximum effort on the structure joints.
SOLAR CARPORT Description
Technical Data SOLAR CARPORT
The Customize PV Shelter
Joining Components-Reinforced concrete fixing structure.-Bracket + 2 pickets for hard grounds.-Bracket + 4 pickets for hard grounds.-Bracket + 6 pickets for hard grounds.
25
The photovoltaic lamp includes:
-MPPT Charge controller that manages the battery with solar energy produced during the day and the on/off/dimming of the night streetlight;-Wide input voltage range of the photovoltaic module (up to 100V);-Max power of the PV panel 225W, 12V ; 450W; 24V-Integrated blocking diode;-Auto-detect of 12V or 24V-Switch for selecting the battery type: hermetic of free acid;-Switch for the selection of battery distance 1mt or 10mt;-Integrated light sensor (via PV module);-Management of the activation of the lead with flow reduction;-Self management of the power –on hours;-Anti-reverse battery protection;-Low-battery protection-Overload and over temperature protection;-IP66 storage for outdoor use-Electric Cables
SOLAR ROAD LAMP DESCRIPTION
TECHNICAL DATA SOLAR ROAD LAMP
CHARGING CONTROLLER
The photovoltaic lamp post comes with:- 1 crystalline PV module;- Charging controller that manages the solar power production during day and the on / off / dimming of the lamp during the night;- Lead Batteries without maintenance;- Steel head pole holder with built-in battery com-partment to the rear opening with a fixed tilt;- Intelligent LED lamp;- Lamp arm Holder;- Pole (OPTIONAL)The post is designed to work up to 12 hours per night (with the possibility of working at reduced luminous flux of the battery charge function) with an autonomy in poor insolation conditions.
26
WATERTreatment Products
27
Acqua dolce 0-1.0001.000-5.0005.000-10.000
30.000
10.000-30.000Acqua altamente salinaAcqua marina
Acqua salmastraAcqua moderata-mente salina
The Desalinating water treatment of sea water and brackish water is a process that reduces the presence of organic, inorganic compo-nents and the salt in the water. Ships, islands and coast areas of certain countries require the application of desalination tecniques in order to create drinkable water.
DESALINATION Kit
• Sea Water supply system.• Microbial Pre-Treatment• Activated carbon filtration• Further Microbial Pre-Treatment• Ultrafiltration• Bacteria reduction • Dosing station• Reverse Osmosis
Advantages Dissalinating Container
Water Species
Technical Data
- Energy consumes reduced thanks to the special membra-nes, that are able to work on low pressures, and to the inverter for the pipe pressure modulation. - Energy saving and minor costs are garanteed.- Accurate Monitoring and Plant automation.- The system Operating Parameters are monitored in re-mote and local master.- Energy recovery system. The plants may be accompanied with a system of energy recovering in order to decrease energy consumption up to 70%.- Salt reduction acording to potable water standards by the OMS.- Automatic Switch from Bi-Osmosis to Mono-Osmosis.- Reduced space volume.
28
Drinkable Water Kit
- Chlorination department.- 90 μm filtration.- Adsorption activated carbon.- Micro Filtration.- Ultra Filtration.- Product dosage.- Reverse Osmosis filtration.- Treated water Accumulation.- Disinfection.
The drinkable water treatment system of brackish water from supplying sources, fountains and aqueduct ecc is based on the membrane filtration function. The vessels can accommo-date ultrafiltration membranes and reverse osmosis mem-branes acording to the “multibarriera” (multi lateral barriers)approach. The use of different filtration membranes grantees a high flexibility of the plant so that it can respond to diffe-rent treatments.Installed on a cargo trailer the plant is conformed in order to be moved on any type of road and it is provvided with an electrical generator.The plant is meant for:- Crude Water extraction.- Crude Water obtaining.
WATER ULTRAFILTRATION KITThe drinkable water treatment system of brackish water from supplying sources, fountains and aqueduct ecc is based on the membrane filtration function. The vessels can accommodate ultrafiltration membranes and reverse osmosis membranes acording to the “multibarriera” (multi lateral barriers)approach. The product comes in a 20 foot long container and the plant is easy to transport and can be mounted on to any flat surface.The plant is meant for:- Sedimentation- Crude Water treatment.- 90 μm filtration.
- Column filtration.- Safe Filtration, 5 μm- Flushing and cleaning system (Cleaning in Place)- Treated Water accumulation.
PROBLEM-Murkiness.-Organic compost and chlorinated.-Iron and magnesium.-Arsenic.
SOLUTION-Sand.-Adsorption activated carbon.-Iron reduction.-Arsenic reduction.
29
Water is essential in our life time but it can be also contagious in certain circunstances. Water quality laws are different in some countries and the OMS (Health World Organization). The European Union acor-ding to the OMS has stated a document which underlines the minimum requirements for potable water. So it is stated that water is not potable if it containes:- Metals.- Arsenic, antimony, boron and selenium.- Toxic organic material ( Organohalogen material, benzene, trihalome-thanes, ecc)To answer to the water consumption needs, special plants have been designed based on reverse osmosis technology, making sure of keeping the maintenance costs, the energy consumption and the loss of energy level.
iIn order to have potable water it is not always necessary to use a filter whith an appropriate filtering tool. Sometimes it is necessary to use advanced technologies on the market in emergency situations or after natural disasters. The reverse osmosis plants, are suitable in many ways for water potabiliza-tion. The advantage are:- Riducted Energy consumes. Thanks to the use of special membranes which are able to work at low pressiures, to inverters which control the pump pressures, energy saving, and cost reductions garanteded.- Accurate monitoring and plant automation.The operating parameters are controlled on the management controlling remote panel.
It is possible to set a threshold which predicts a series of auto-matic operations including sending the system in block.- Microbiologial parameter, chemi-cal and radioactive fulfillment.- Plant security. - Automatic transfer from bi-osmo-sis to mono-osmosis.- Collecting pipes in PVDF mate-rial.- Space capacity reduction.
Reverse osmosis plants are entirely assembled on to skid in order to help the carriage and the installation. To ensure maximum reliability and flexibility of the operation, each
plant is equipped with:• Activated Carbon Filtration• Filtration micron• Ultrafiltration• UV sterilization• Dosing system antiencrustation • Reverse Bi-Osmosis
• automatic flushing system ofmembranes• chemical washing of the membranes system
POTABLE WATER KIT
30
The system provides an automatic and continuous operation; the traceability register allows to control events occurred locally and remotely.
A dialysis patient comes into contact, weekly, with a large quantity of water that, therefore, must respond to high requirements for quality and purity. Specifically, the dialysis fluid must have:
The system comes complete with:• Pretreatment Micronic• Activated Carbon Filtration• Further filtration micron• Ultrafiltration• UV sterilization• Reverse Bi-osmosisThe system provides an automatic and continuous operation; the traceability register allows to control events occurred locally and remotely.
The advantages of the compact systems are:• Certified Medical Device, in accordance with the Euro-pean Directive 93/42 EEC. The entire process chain, from pretreatment to bi-osmosis, is certified Medical Device• Ultrafiltration. This low-pressure separation process is able to filter viruses, bacteria, sediments and colloidal substances by means of semi-permeable hollow fiber membranes having pores with a diameter between 0.01 and 0.1 microns. Ultrafiltration ensures sanitation of osmotic membranes, extending a 20% of their useful life and increasing its effectiveness.• UV lamp. The UV germicidal lamp guarantees the disin-fection of water in the ring return input line osmosis• Automatic switching to bi-osmosis mono-osmosis.• Programmed Turning on and off and easily manageable by PLC.• Collecting pipes made of PVDF• space-saving space.
- Proper electrolyte composition.- A low concentration or absence of organic and inorganic chemi-cal micropollutants.- A low concentration or absence of bacteria and endotoxins.
MEDICAL KIT
31
The water used in food production has to meet high health and safety standards for the protection of consumer health.Water is properly used when there is compliance with the quality parameters established by the regulations in force. In particular, the treatment of the waters process, shall ensure:- The prevention of contami-nation- The removal of harmful
substances such as pathogens (bacteria, phytoplasmas, viru-ses), pesticide residues, heavy metals, etc.- The satisfaction of organo-leptic parameters, microbiologi-cal and chemical.
Water treatment plants are designed in order to meet the needs of the different stages of production of the food in-dustry and beverage industry, in the respect laws of the environment and foods.The advantages are:• Energy savings and lower operating costs. Reduced energy consumption and low costs thanks to the use of special membranes, that work at low pressures, and inverter systems for the modulation of pressurization pumps.• Accurate monitoring and au-tomation system. The system operating parameters are monitored both locally and remotely framework. It is pos-
sible to set a threshold value which shall predict a series of automatic operations including the blocking of the system.• Compactness, plant flexibility and easy maintenance. The modularity of the system is well suited in every season of the year. It can also get the notice of necessary mainte-nance directly from the mana-gement controlling panel.• Plant safety.
The Directive 98/83 / EC which governs the quality of water intended for human consumption, including both for drinking water as well as those
used in food production, requi-res the application of innovati-ve technical solutions, capable of offering the best results in costs competitive.
HEALTH SOLUTION KIT
Water Treatment Products In Food Industry
32
WATERProducts
33
Prezzo 3.700€ (garanzia 10 anni)prezzo netto 200€ incluso PVprezzo netto 370€prezzo netto 200€prezzo netto 200€Totale 770€
7cent/litro
30 litri X 365 GIORNI= 10.950 litri
Kit filtro per 1 annoAmmortamento impiantoKit filtriKit batterie
Prezzo al litro
Water production per year
The product produces drinkable water without the need for con-nection to the water system.STEP 1: Air filtration. The first phase of electrostatic air filtration-removes dust, the pollens, molds and other contaminated agents suspended in the air that enters ER NEPTUNE.STEP 2: Condensation. The flow of air that enters the machine is cooled and brought to the point of condensation to allow any moisture contained in the air of passing from the gaseous state to the liquid state.STEP 3: Sterilization. After finishing the process of condensation, the water is filtered and stored in a tank in which develops a ste-rilization process using UV lamps.STEP 4: Purification. Without the use of batteries, water is send into a special filtration system that makes it pure and healthy.STEP 5: Dispensing. With a simple pressure on the panel’s button, it will be possible to have without any effort, potable and tasty water.
Production: 30 L / day at 28ºC with 80% RHDimensions: 80 x 60 x 100 cm (solar panel appart)Weight: 39.5 kg + 100 kg (fotovoltaic kit)Tank: 30 LMaterial: Stainless SteelPower supplier: Sun
Neptune KIT The Potable Water Generator
-Performance: producing up to 30 liters of water per day.-Purification water: of a 5-stage filtration process.-Purification air: washable filter for the removal of dust and other airborne particles Storage Capacity: 30 liters total water accumulation.-Electronic sensors: each critical-component of the system is equipped with an electronic sensor that ensures the proper operation and sends an alarm in case of any malfunction.energy -Saving: car of the capacitor being switched off in the event of raggiugimento the maximum water level in the tank in order to both reduce the consume of energy that preserve the battery life.-Multifunzionale: thanks to the air filtration and condensation dell’umitità, thanks to ER NEPTUNE, the air of the room in which it is bound will be more pure and less humid.-Easy maintenance: ER NEPTUNE is designed to be simple and for easy maintenance.
COSTS COMPARISONTECHNICAL DATA
TECHNICAL DESCRIPTION
COUNTING COSTS
34
OFFICINE DI TREVI Catalogo 2014
Kit Solare
3,5
3,0
2,1
2,8
3,5
3,0
2,8
3,6
Catalogo Catalogue 2014 OFFICINE DI TREVI
SOLARE 2
APPLICAZIONIPer il sollevamento dell’acqua da pozzi profondi in impianti alimen-tati da energia solare.
CARATTERISTICHEL’innovativo impianto si compone di tre elementi:• i pannelli fotovoltaici (non forniti)• il quadro di regolazione ad inverter• l’elettropompaL’inverter Solare 2 lavora in presen-za della tensione fornita daipannelli fotovoltaici, in assenza della quale l’impianto non funziona.Non necessita di batterie d’accumu-lo per l’energia elettrica in quanto, con questo sistema, l’acqua viene pompata e stoccata durante il gior-no, per l’eventuale utilizzo durante la notte.Per un corretto funzionamento l’in-verter Solare 2 deve essere alimen-tato a 320 Vcc o 560 Vcc.L’inverter, opportunamente installa-to e tarato, può spegnere l’elettro-pompa in caso di mandata chiusa, è dotato di marcia a secco e blocca il motore in caso di assorbimento ec-cessivo.L’elettropompa funziona con una tensione di lavoro trifase 230 V e trifase 400 V; ciò fa sì che gli assor-bimenti siano particolarmente con-tenuti.
CONDIZIONI DI LAVORO• L’inverter deve essere posizionato
in ambiente protetto e ventilato.• Temperatura di esercizio inverter:
min 5°C - max 50°C.• Liquido pompato: acqua pulita non
aggressiva, priva di sedimenti solidi.• La pompa non può girare a secco.• Corpo pompa sempre completa-
mente immerso.• Temperatura del liquido pompato:
min 5°C - max 30°C.• Posizione di funzionamento elettro-
pompa verticale.• Numero max avviamenti orari elet-
tropompa: 20.
Catalogo 2014 OFFICINE DI TREVI
Water supply from deep wells, ci-vil and industrial raising systems, rain and running irrigation, fire fighting systems, aqueducts.
• External pump case, deliveryhead, suction, shaft, impellersand diffusers in stainless steel.• The check valve made of stainless steel is installed inside the delivery head.
• Motor coupling meets NEMA standards. • 2 poles asynchronous motor, 50 Hz, 2850 rpm.• Class F insulation.• IP68 protection.• Working voltage: three-phase 400 V
• Pumped liquid: clean water, non aggressive, without solid particles.• The pump can not operate in dry conditions.• Pump body always completely submerged.• Temperature of pumped liquid:min 5°C - max 90°C.• Vertical operating position.• Maximum number of starts perhour: 20.
APPLICATIONS
WORKING CONDITIONSDATA
TECHNICAL DATA
35
OFFICINE DI TREVI Catalogo 2014
Kit Solare
3,5
3,0
2,1
2,8
3,5
3,0
2,8
3,6
Raising of clean water from deep wells and tanks, civil and industrial water raising system, rain and running irrigation, aqueducts.
. Multistage centrifugal electric submersible pumps for wells. . External pump case, delivery port, suction, motor shaft and others components in stainless steel. . Impellers, diffusers in special technopolymer. . The check valve made of stainless steel is installed inside the delivery head. . The pump is equipped with 30 m of H07RN-F electric cable.. External diameter: max 105 mm.
. 2 poles asynchronous motor, 50 Hz, 2850 rpm. . Class F insulation. . IP68 protection. . Working voltage: single-phase 230 V, three-phase 400 V. . The electric motor is cooled by non-toxic, non-polluting liquid.
. Pumped liquid: clean water, non aggressive, without solid particles. . The pump can not operate in dry conditions. . Pump body always completely submerged. . Temperature of pumped liquid: min 5°C - max 30°C. . Vertical operating position. . Maximum immersion depth: 10 m. . Maximum number of starts per hour: 20.
TECHNICAL DATA
APPLICATIONS
WORKING CONDITIONSDATA
36
Submersible pumps for clean water pumping from wells, cisterns and storage tanks. The pumps is long-life designed and is fully provided with control panel and built-in capacitor and thermal motor protection.
Stand-alone photovoltaic system for water pumping stations. Ecosolar P60 converts solar energy obtained from photovoltaic panels, into 230 Volts alternating current. The unused energy is stored in batteries. Unlike conventional inverter systems, which regulate motor speed according to irradiation available, Ecosolar P60, thanks to electric batteries, guarantees the operation of the electric pump at the highest regimes, even in the total absence of sunlight. Ecosolar P60 is also an electric power supply system in case of emer-gency, in fact, it is designed to be connected to the electrical network. In this way the system uses the current network as a priority, but during blackouts it uses the energy of the panels and batteries, ensuring the operation of the electric pump. Safe and reliable, it can be used to power any users at 230 Volts, with compatible power. The LCD display makes it intuitive and easy to use.
It’s designed for both continuous and intermittent working, it’s particularly sui-table for all installation in remote locations and for applications such as irriga-tion of fields and greenhouses, watering animals and pressurization generally.
-Max Flow rate: 20 m³/day-Max Head: 62 m (6,08 bar)
No periodic unlocking maintenance of the impeller.High performances.Horizontal and vertical working.Eco-friendly product (non-toxic paints and oils, recyclable packaging).
The Product once is submerge can be ready to use. It has a control panel, a protected engine and a 10 metre cable. It uses non toxic paints, certified to be in contact with edable products and recycable packagings.The product garantees High performances, low energy usage and a 2 year warranty.It can work indipendently using clean and renewable energy from the sun.
USE
USE
PERFORMANCEFUNCTION
ECOFRIENDLY
PERFORMANCE
37
PV Products
38
The solar cells used in our modules offer an high conversion efficiency of the sunlight. These property guarantee high yields. Our solar modules have only positive power tolerance of 0 + 5 W. These pledge a more stable production. The modules resist at the worst meteorological conditions and at extreme temperature
All Waris solar modules are optimazed for every type of PV system, from residential to industrial and PV plant.
Waris solar modules have a 12 years on product defects and a linear power output warranty:
•97% towards the nominal power* during the first life year and afterwards a maximum degradation not up at an annual 0,6%•92% towards the nominal power* within the first 10 years from the purchase•85% towards the nominal power* between the 11th and the 20th year from the purchase•83% towards the nominal power* between the 21st and the 25th year from the purchase
The modules FS Series 2 and Series 3 thin film highly develo-ped technology based on CdTe are distinguished by high effi-ciency even in different climatic conditions. The modules have an extraordinary performance even with low irradiation and a high temperature coefficient. The mo-dules provide verifiably advance the calculated yields coeffieciente with a very high performance.Frameless laminate is very du-rable, efficient, inexpensive and recyclable. The production is carried out in modern factories are mainly automated that are certified according to the ISO 9001 (quality) and ISO 14001 (environmental management). The modules are independently tested by leading European and Ameri-can institutions and reliability and safety certificates.
The photovoltaic modules of the series 2 and 3 are tested to a voltage of 1000 VDC limit and certified in accordance with IEC 61646 and Class II. First Solar provides the leaders in the field of photovoltaic project developers and system solutions in the integration of thin films at low cost for photovoltaic systems connected to large network. Their ap-plication engineers are able to offer comprehensive technical assistance, and to provide a detailed technical documenta-tion to support the design, installation and long-term use of photovoltaic systems with high efficiency.
The warranty for defects in materials and production is five (5) years. The power rating (Pmpp +/- 5%) during the first ten (10) years is 90% and 80% during twenty-five (25) years, subject to the conditions and terms of guarantee.The management of the lifecycle of the modules provides a pre-funded retirement and recycling program, which guaran-tees the owner the withdrawal and Free module recycling at the end of their lifespan.
APPLICATIONS
WARRANTY
TECHNICAL DATA
TECHNICAL DATA
WARRANTY
APPLICATIONS
MONOCRYSTALLINe72CELLS
POLICRYSTALLINE 72CELLS
39
During the first year the panel will increase the energy production around 7-9% of what it normaly produces. This advantage will increase in time, reaching up to further 20% of energy for the next 25 years.
Power (Pnom) 11 333 WPower Tolerance +5/–0%Media Module efficiency12 20,5%Power Tension (Vmpp) 54,7 VMaximum current power (Impp) 6,09 AOpen circuit current (Voc) 65,3 VShort circuit current (Isc) 6,46 AMax system Tension 1000 V IEC & 600 V ULMax fuse current 15 ACoeff. temp. power –0,38% / o CCoeff. temp. tension –176,6 mV / o CCoeff. temp. current 3,5 mA / o C
Temperature –40° C to +85° CImpact resistenceHailstorm diameter 25 mm each speed of 23 m/sA classSolar cells96 monocrystalline cells Maxeon of II generationTempered Glass of high transmissionContainer IP-65, Yukita (YS-254/YS-255)Weight 18,6 kgMaximum loadWind: 2400 Pa, 244 kg/m² front and backSnow: 5400 Pa, 550 kg/m² frontBlack Alluminium frame
Test standard13IEC 61215, IEC 61730, UL 1703 (fire resistent)Quality test ISO 9001:2008, ISO 14001:2004Compliance EHS RoHS, OHSAS 18001:2007, no lead, PV Cycle, REACH SVHC-163Environmental CompatibilityCradle to CradleAmmonia test IEC 62716Resistance test sand storms 10.1109/PVSC.2013.6744437Resistance test to salty water IEC 61701 (max level)Test PID Absence of degradation induced by voltage: 1000 V9
Mechanical Data
Electrical Data
Electrical Data
-Policrystalline cells 72 / 6 x 12-Efficiency 16%-IP 65-Alluminium Frame
Technical Data
40
DOTAZIONE
Connessione CC/CA
DisplayInterfacce
Garanzia
Relè multifunzione/Ingressi digitali
MC4,H4,SUNCLIX/spinaLCD a due righeRS485/WLAN/ETHERNET
15 anni
1/4
SAM INVERTER
2100W170V-400V/380
80V/110V14A1/1
1.000 VMPP 580-850 V1CC 6
230V/50Hz9.1A1
0,90
1/1
25.000 VA25.000 W
220V/230V/240V180V/277V50Hz/60Hz
96.8%/96.2%
333x425x147mm13,7kgIP65
<28dB0W
95%
- Free site selection due to IP65- Easy installation and maintenance due to “Plug & Play” connection- Interface selection-Ethernet,Wi-Fi and RS485 for more flexible configuration and system monitoring- Multi-lingual 2-line LCD display- Digital inputs for the economic connection of a ripple control receiver.- Configurable multi-function replay output.- Highest earnings through max.efficiency of 96.8%- Safe operation due to integrated DC-switch- No Fan design for low failure rate and longevi-ty.- Sturdy design due to High Accelerated Life Testing(HALT) and rigorous Multiple Environmental Over Stress Testing (MEOST).- Defeating shade effect by Global Peak Tracker
OUTPUT data
Range
Technical Data
Max Power
Power
Max Range/ European range
DimensionWeightProtection Grade
Noise
Topology
Nocturnal ConsumeCoolingHumidity
CA Power maxCA VoltageVoltage CA rangeFrequency CANetwork power VoltageCurrent max. exitPower Factor
Factor Range Power
Imission fase/connection fase
With out Tran-sformer
Convention
Voltage rangeCurrent input maxNumber of inputs MPP
Max Voltage inputGamma TensionNumber of MPPNumber of inputs
Max Voltage
Data INPUT
Technical Data
41
Electric current max
50Hz/60Hz (45-65Hz
<2,0 %
25.000 VA25.000 W
725x510x225mm35,7kgIP661CC/CA 2/3<1W-25/+60 °C0-100%2.000mCC 6X DC+ 6X DC-TERMINALI A VITE 2.5-16mmCA 5 poli AC terminali a vite 2.5-16mm 2
2
0-1 ind./cap.
3~NPE 380 V / 220 V o 3~NPE 400 V / 230 V (+20 % /- 30 %)
Minimum tension entranceStarting supply Tension Entrance TensionMax entrance TensionTension GammaN° of MPPNumber of entrancesExit generator power
Max electricity to the short circuit
44.2 A66.3 A
580 V650 V580 V1.000 VMPP 580-850 V1CC 637,8 kW di picco
PROTEZIONE INVERSIONE POLARITA’
The Inverter is designed to be used for high performance. The three-phase inverter of 25.0 and 27.okW of power is perfectly suitable for big PV plants. Thanks to it’s light weight this inverter without a transformer may be installed quickly indoor or outdoor. This Inverter is designed with a IP66 con-tainer. The voltage system of 1000V/dc and the MPP high range of 580 and 800 V/dc of power garantee maximum flexibility in the system and the string collection boxes aren’t no more necessary. The Fronius Inverters come in order to satisfy the needs of the future network. A series of smart functions, known as “Advanced Grid Features”, are integrated into the device and include controlling functions for monito-ring the relative and actual power. This functions are desig-ned for making the networks work stable even when the PV plant’s density is very high and to avoid further interruptions of the electricity supply and the loss of performance.
-INTERFACCE WLAN / Ethernet LAN.web, Modbus TCP SunSpec.-6 input o 4 input/output digital Interface to ripple control receiver.-USB (Presa Tipo A) Datalogging, inverter update via USB flash drive.-2 prese RJ45 (RS422)-Uscita segnale Energy management-Datalogger and Webserver Integrated-Input external Interfaccia S0-Meter/ Input, for over tenction, protection RS485 Modbus RTU SunSpec o meter connection.
Technical Data
Input Data
Out Data
PowerMax Exit powerNetwork connection
Gamma frequency
Distorsion FactorPower Factor
General data
DimensionsWeightDegree of protectionClass protectionOver tension categoryNight ConsumGamma temperatureAir umidity allowdMax. altitudeConnection
Connection
42
The product is a charge regulator for the charge of batteries from PV module; it has been special-ly designed for the use in offgrid PV lighting systems (PV street-lamp). SPB-LS is housed inside a metal box that is protected from water (IP66 degree); therefore it can be installed directly on the PV pole without having to add additional protections. The charge circuit from PV module has got an efficient algorithm for the search of the maximum power point (MPPT) that is capable of opera-ting over an extended field of voltages. It is allowed a maximum voltage on the PV module up to 100V. The regulator can charge either 12V Pb batteries or 24V Pb batteries. On power ON, SPB-LS automatically recognizes if the battery is at 12V or 24V and it automatically adjusts the charge thresholds. The regulator automatically manages the power on and off of the lamp.At dusk (when the voltage of the PV module drops below the Vnight threshold) the charge control-ler switches on the lamp and keeps it on for a number of hours that can be set by the user. You can also set some programs for lamp’s power on with working hours with reduced flux (dimmer). In this way you can check accurately the lamp consumption so to remain inside the dimensioning of the PV off-grid system.
- MPPT charge.- Wide range of input volta-geof the PV module (up to
100V).- Max power of PV module: 225W @ 12V and 450W @
24V.- Integrated blocking diode.
- 12/24V autodetect.- Switch for battery selection: sealed or flooded lead acid.
- Switch for selection of battery distance: 1mt or 10mt
(base of pole).- Switch for setting depth of
discharge (DoD) 30% or 70%.- Battery charge compensated
in temperature- Integrated light sensor
(through PV module).- Possible load activation with
flux reduction.- Switch to program the hours of load activation.
- Self-management for hours of lamp activation.
- Protection for battery pola-rity inversion.
- Overload and overtempera-ture protection.
- Low battery protection.- LEDs for the following indi-cations: 12/24V; on/off load; on/off flux reduction; current
from PV; protections.- IP66 metal box for outdoor
application.- Wires for outdoor electrical
cabling
Energy Production
Function description
43
The new generation is based on the successful platform which deli-vers maximum yields with no maintenance.Working hand-in-hand with our customers, we have further improved the devices, making them even more future-proof, user-friendly and reliable. Whether you add accumulators in future, integrate the PV system in smart grids or the regulations change – the new softwa-re means you‘re well equipped for the future. Plan and build your decentralized PV project flexibly. The simple layout can be rapidly multiplied, particularly with large systems. Partial systems connected to the grid during the construction phase provide early yields. The devices are designed for worldwide use, with special versions for North America (UL version) and Japan (JP version).POWER: 8-10-13-17-20-23kW
The Wave Storage is a compact, easy to install and allows you right away to save on your bill, because it maximizes the use of energy from the photovoltaic field. Its compact design allows you to have in a single product all the necessary components for the conversion and optimal energy manage-ment, monitoring and more precise assessment of what are the most efficient energy flow for maximum use of photovoltaic production and the while minimizing the demand from the net-work.
TECHNICAL DATAThe House Storage
For ItalyTechnical DescriptionEntering DC (FV)Max power (kWp) 6,6 (3,3 × 2)Max Voltage (V) 550MPPT / Voltage (V) 125÷500 / 400 per StringInput Voltage Min./Iniz. 125 / 150 per StringMax Current input ( A) 15 per StringN. Canali MPPT 2N. Di ingressi DC 2Connector type FV MC4Release ACPower (kVA) 4,6Voltage Power (Vac) 230Frequency (Hz) 50Release current AC (A) 20Loss in stand-by (W) 25Number of phases 1 / 1Efficiency EU Da FV a Rete (%) 95BatteriaTechnology lithium battery (Lithium Manganese Oxide)Power (kW) 2Capacity (kWh) 3,6 (DoD 90%, capacità utilizzabi-le: 3,24)AltroDimensions mm (L × P × A) 1.000 × 267 × 680Peso (kg) 95Temperature di esercizio (°C) -10÷40Umidità (%) Max. 95 (non condensante)Grado IP (IP) 21CE: IEC 62109-1 / 2, CEI 0-21, CEWarranty (Year) 5 (Product) / 10 (Performance)Energy Management SystemMonitoring (Device / Remote) Web, MobileUpdate Software Via Internet
REFUSOL INVERTER
44
REGOLATORE DI RICARICA 20
REGOLATORE DI RICARICA 60
REGOLATORE DI RICARICA 15
• PWM technology• Max module power 700W @12V, 1400W @24V,2800W @48V• Max load current 60A• Internal block diode• Pb-Lead acid, Pb-AGM, Pb-Gel batteries• Auto-detection battery voltage (12V - 24V - 48V)• 19 programs to manage the load• 48 signs LCD graphic display for user interface• Low battery protection• Over-temperature protection• Protection from inverted polarity of the battery• Output overload protection• IP20 metallic box
• PWM technology• Max module power 280W @12V and 560W @24V• Max load current 20A• Internal block diode• Pb-Lead acid, Pb-AGM, Pb-Gel batteries• Auto-detection battery voltage (12V - 24V)• 19 programs to manage the load• 48 signs LCD graphic display for user interface• Low battery protection• Over-temperature protection• Protection from inverted polarity of the battery• Output overload protection• IP20 metallic box
The product is charge controller for PV application with automatic charge management of two batte-ries, one primary and one secondary, with Blue-tooth connection for control with dedicated APP for Android and iOS mobile device. The USB port output can be used for direct smartphone, tablet and battery bank charge.
The charging regulators are characterized by their reliability and robustness due to the very low prices. The controller is designed to recharge, by means of photovoltaic panels, batteries of different types, therefore, ideal for the realization of small off-grid photovoltaic systems with a sy-stem voltage at 12V or 24V. The product in addition to performing the function of charge of the batteries, also performs the function of maintaining the overload avoiding battery is that the deep discharge so as to maintain unchanged the dell’accumolatore efficiency. The product detects the day / night on the basis of the panel voltage and is equipped with a large display for viewing all system parameters.
Technical Data
Technical Data
45
Portfolio
46
WIND POWER
47
The wind power struc-ture converses the
wind energy in electric energy, normally
thanks to wind gene-rators that produce
electric current throu-gh wind turbines and wind pump. The wind power is a clean and
renewable alternative compared to the fossil fuel. The kind of ener-
gy doesn’t produce GHG emissions and doesn’t need a big
area of building. Wind power (Minieolico) is a small plant, appro-priate for the dome-stic use and also can integrate the energy
use of small firms through the action of
single generators.These plants are
usually are made up of the horizontal axis type generators, with a rotor diameter from 3 mt up to 20mt and a freehub high from
10mt up to 20mt.Wind power (Minieo-lico) usually means a 20 kW-200 KW plant, Wind power (Micro-eolico) means 1kW-
20kW plant.These plants can
exploit soft and po-werful wind and can intercept the unex-
pected gusts.
48
Generatore
Control system
Hights available
Warranty
Monitoring system
Inverter
Sopravento
15,96m
Asincrono
PLC + Touch screen
24/27m
2 years which can be increased
Web App
60kW
Trifase, 4 poli,400 Vac
2199,99 m
7,5 m
YAW
60kW
60Rpm
III
12m/s
52,5m/s
25m/s
2500Kg
The wind generators send the feedback to the controlling station, where there is a data elaboration, which includes:-Reporting system;-Real time – monitoring;-Production;-Warnings;
Thanks to these tools we are able to constantly manage the turbines and supply a ready technical assistance. The webapp allows the user to access to the daily/weekly/
monthly pro-duction data, and to the esti-mated return. The wind generator is equipped with a support tower managed by a hydraulic lifting system, in order to obtain econo-mic advantages both during installation and ordinary and extraordinary maintenance, since all the operations are performed on the ground.The wind generators are directly connected to the power grid without inverter, in order to in-crease the ove-rall efficiency of the system and eliminate the failures.
The wind generator safety is guaranteed by braking devices the hydraulic brake makes it possible to adjust the braking avoiding mechanical stress, the aerodynamic brake is autonomous and limits the rotor overspeed.
WIND TURBINE Technical data
generator
Warranty
Wind structure Highht
Configuration
Power
Rotor Speed
Turbine Class IEC 61400-2
Wind speed
Max Wind speed
Max wind speed cut-off
Weight
Generator
Controllings
Rotor Diameter
Type
Power
Configuration
Area
Wind 1 pole of 3 lenght
Wind pole material
Power regulation
“Not inserted”
Fiberglass
Rotor
49
GEOTHERMAL ENERGY
50
The electricity produced by photovoltaic systems flats into the heat pumps. The air conditioning systems, mana-ged by an intelligent system, will have no operating costs and achieve the maximum environmental sustainability with remarkably low CO2 emission.All the energy produced will be used on site in a carbon neutral virtuous system.The geothermal plant is the easiest system to create air conditioning system from the power grid. The geother-mal plant will eliminate all the risks related to the use of gas-fired boilers and the thermal distribution is exploi-table for heating through the ceiling and the floor thanks to the panels.
51
“U” Spirale Spirale Spirale
32
-15-1
32
1060404,0
32
2060402,83
32
560404,83
FunzionamentoSonda Geotermica
VANTAGGISonda Geotermica
Geothermal energy is generated thanks to geological heat sources and can be considered as alternative and renewable energy. In Italy, the low enthalpy geothermal ener-gy is still not developed because of the lack of culture and high costs. ER Cool Heat has developed an innovative systems of production and utilization of geothermal energy with low enthalpy for air conditioning in residential, commercial and industrial buildings. The geothermail spiral is composed of a PEAD pipe assembled at the factory. The spiral can also be sited in metal cages used to achieve the
piles armor realizing an innovative “energy pile”.The spiral under construc-tion, storage and carry in the pipeline is compact, that is with all the joints close together, while stretching our during the laying for the entire length of the hole thanks to the simple gravitational effect.The maximum distance between the joints is limited by special spacers, which are also assem-bled in the factory. This technology is appropriate for the building integrated with any type of geother-mal pump.
ADVANTAGES:- Increasing dispersant area for each meter of the hole;- Increasing pipe length;- Decreasing cost of drilling;-Increasing speed of execution.
General Data
Technical Data
PE Pipe Diameter
Spiral StepHole DiameterDiametro SpiralCoefficient multiplier Cm
52
53
Pellets
Gusci di Nocciole
Gusci di Mandorle
Gusci di Prugne
Gusci di Pistacchio
Gusci di Pinoli
Gusci di Cucina
Osso di Pesca
Osso di Albicooca
Nocciolino di Oliva
Semi di UVA
MAIS
LEGNA
CIPPATO
SEGATURA
tRUCIOLI
TRONCHI DI SEGATURA
TRACCI DI POTATURA
INTRODUCTION
The term biomass refers to a collection of animal or vegetable organisms present in aquatic and terrestrial environments. The concept of biomass is often treated in a different way depending on the context. Biomass is important in the fields of renewable energy and ecology. The European regulations define biomass as “the biodegradable parts of products, waste and residues of biological origin from agriculture, forestry and related industries, including fishing, as well as the biodegradable fraction of munici-pal waste. The biomass, during the combustion , emit the same amount of CO2 absorbed previously by the plants during their growth process. The use of biomass for energy purposes not therefore causes the release of new co2 and, given their nature, biodegradability is a further advantage for the environment.
Biomass, however, have some disadvantages:-Biomass require large areas because of the low energy density- Biomass require the use of fertilizers;-There are problems of logistics for the supply of resources;-The annual output is not constant.
Estimate saving amount to create energy such as: METHANE, GPL (Liquified gas) GASOLINE.
WASTE USED IN THE BIOMASS INDUSTRY
54
Fitomassa
Zoomassa
Biomassa
BIOCARBURANTI
Thanks to the fermentation of plants, such as sugar cane, beet and corn, can be derived ethanol or ethyl alcohol. They can be used as fuel in lieu of gasoli-ne engines. The oilseed biomass are suitable for the generation of biodiesel as bioethanol, biomethanol, vegetable oils and synthetic hydrocarbons.There are some negative consequences resulting from biofuels:- arable land feed the machines, not people- the exploitation of biomass rising costs of raw materials- there is a risk of ruining the performance of the lands.
CLASS
The biomasses are classified by three criteria:- water content-origin-vitality
Depending on their origin, the biomass can be divided into:- phytomass: coming from plants- zoomassa: from animals- microbial biomass: from microorganisms.
Finally, according to the vitality, one can di-stinguish a living biomass, made up of living organisms, from a dead biomass consisting of dead organisms.
ENERGY PERFORMANCE WITH VEGETABLE BIOMASSES
The plants have the ability to convert the solar energy into chemical energy, thanks to photosynthesis (Water + CO2 + light + oxygen).The overall energy efficiency of carbohydrate formation is represented by the obtained biomass and the available solar energy.
ENERGY COMPOSITION
Biomass consists of dead or alive organisms and different elements. The most important elements are carbohydrates, fats and proteins.
BIOGAS
The cultivated plants, waste and animal sludge can be fermented. The deve-lopment of microorganisms generates biogas. It will be used as fuel for heating or cooling and for the production of electrical energy.
55
200kWe200kWt15kW185kWe
0kWt200kWt7.5001.088t4%37,8 kW di picco
The gasification technology consists in a cogeneration and trigeneration plant. The gasification of the combustible material takes place without combustion and without CO2 emissions. The temperature in the first reactor reaches 800 ° C and 1400 ° C in the second reactor. This gasification process does not allow the formation of dioxins. The process generates a combustible gas (syngas) combustion of which generates very low particulate emissions
ADVANTAGES COMPARED TO A INCINERATOR
- Elimination of direct emissions from combustion of materials- High production performance- High heat recovery performanceThe system is configurable in three power sizes: (1000 kWe, 500 kWe, 250kWe), and is able to gasify different types of materials: wood biomass, waste materials, agricultural processing, paper, plastic, tires RSU
INPUT DATA
TECHNICAL DATA
Electric power
Electricity Self consumeElectricity into the network
Thermal Self consumeThermal powerAnnual Hour functionFuel ConsumptionAsh ProductionAnnual ash quantity
Thermal Power
56
LIGHTNING
57
R-PLANE
OTTOCENTO
ApplicationsAvenues, roads, parks and gardens, historical centres, cycle paths.Suggested installation height: 3 - 7 m.
Technical Data• LED designed pressure fused aluminium body• High efficiency PMMA optics• Flat protective diffuser with 4 mm extra clear tempered glass for security (not available in 3D vers.)• Anodized aluminum treatment• Polyester powder painting, color “Dark Smoke” RAL 7016 embossed• Grade of protection IP66• Impact resistance IK10• Insulation Class I or II• TCS - Thermal Cooling System
• Full cut-off (not for 3D vers.)• Stainless steel or insulated screws• Photobiological safety refer to EN 62471:2008 and IEC/TI 62471:2009• Made in Italy - EU - CE mark• Dimensions: LANT33 = 300 x 300 x 650 mm. Weight: around 5.7kg LANT44 = 400 x 400 x 750 mm. Weight: about 8.8 kg
MountingQuadripode with nipples M24x3x40 mm and double nut AISI304 stainless steel included, other equipment on demand.On post or wall
ApplicationStreet lighting in suspended mode. Great range of mounting heights: 6 - 12 m..
Technical Data• Designed, under pressure fused aluminium and anodized aluminium chassis• Anodized aluminum treatment• Polyester powder paint colour: “Dark Smoke” and embossed RAL 7016 (“Silver” RAL 9006 colour is available on request) • High efficiency PMMA optics • Flat protective diffuser with 4 mm extra clear tempered glass • IP66 Grade of protection, mounted • Impact resistance: IK09 • Insulation Class I or II • TCS - Thermal Cooling System • Full cut-off • Stainless steel or insulated outside screws • Photobiological safety, refer to EN 62471:2008 and IEC/TI 62471:2009 • Made in Italy - EU - CE mark • Dimensions 350x350 mm, weight 5 Kg.
Advantages• Wide range of optics, power and colour • Driver is included in the body • Functional versions: OF - DM - DMP - TLC - VDC • Automatic temperature control • Dimmable/Programmable • Quick cleaning and minimal maintenance • Option of supplementary protection against line surges • Long life reliability
MountingWall/roof fixing by orientable bracket included
We Install thiese products only under commission or tenders or for startups.
58
2D SHEET
3D SHEET
ApplicationsRefitting of old fashioned lanterns or outdoor fixtures. Great range of mounting heights: 6 - 11 m.
Technical data• Designed, estruded and anodized aluminium chassis • High efficiency PMMA optics • Flat protective diffuser with 4 mm extra clear tempered glass • IP66 Grade of protection, mounted • Impact resistance: IK09 • Insulation Class I or II • TCS - Thermal Cooling System • Full cut-off • Stainless steel or insulated outside screws • Photobiological safety, refer to EN 62471:2008 and IEC/TI 62471:2009 • Made in Italy - EU - CE mark • Dimension: 220x270 mm plus interface plate, weight 8,5 Kg.
Advantages• The LED Module is completely closed and certified in order to make the light fitting a mechanical support without any electrical element • Conservation and preservation of historical and monumental heritage • Elegant black finish colour which adapts well to most existing lanterns/fittings • LED Module, optics and drivers are included in an iron-free body • Flexibility and the option to upgrade the existing structures with reduced investment costs
• Wide range of white tonality and high colour rendering: “Urban Renaissance by Litek” • Functional versions: OF - DM - DMP - TLC - VDC • Automatic temperature control • Dimmable/Programmable • Quick cleaning and minimal maintenance• Option of supplementary protection against line surges• Long life reliability.
MountingDig a furnished mechanical interface
ApplicationsRefitting of old fashioned outdoor lanterns or fixtures.Great range of mounting height 2 - 6 mt
Technical Data• Extruded anodized aluminum heat sink• High efficiency PMMA/PC street or intensive optics and diffuser• Grade of protection IP66• Impact resistance IK10• Insulation Class I or II
• TCS - Thermal Cooling System• Stainless steel or insulated outside screws• Photobiological safety refer to EN 62471:2008 and IEC/TI 62471:2009• Made in Italy - EU - CE mark• Dimensions: 100x100 mm minimum. Weight: 1/1,5 Kg
Advantages• Conservation and preservation of important historical heritage sites• Elegant black finish colour which easily adapts to most existing lanterns/fittings• Flexibility to upgrade the existing structures with reduced investment costs• Wide range of white tonality and high colour rende-ring: “Urban Renaissance by Litek”• Functional versions: OF - DM - DMP - TLC - VDC• Automatic temperature control• Dimmable/Programmable
• Specific scheduled maintenance suggested • Option of supplementary protec-tion against line surges • Long life reliability
MountingDig a furnished mechanical inter-face
We Install thiese products only under commission or tenders or for startups.
59
WIRE PLANE
SLIDE
QUALUCE
Caratteristiche tecniche-Dissipazione termica ottimale-Effetto luminoso uniforme-Driver incluso-Alta efficienza 120 lm/W
Tipologia-Apparecchio LED ad incassoe sospensione-Cornice-Alluminio laccato bianco-Schermo-Diffusore in policarbonato ad alta trasmittanza-Corpo In alluminio
Applicazione-Illuminazione hotel, uffici.
Tipologia-Apparecchio LED dedicatoper illuminazione stradale urbana-Corpo in pressofusione di allu-minio-Nano-ottiche in materiale acrilicotrasparente su ogni singolo LED.-Vetro piano trasparente di tipo extra-chiaro-Caricamento in sole sei ore per tre giorni di autonomia-Dimmerabilità automatica in base a condizioni di luce e presenza umana.-Installazione immediata
-Autoalimentato privo di connes-sione alla rete-Dissipazione termica ottimale
Caratteristiche tecniche• Batteria a litio• Regolatore di carica• Pannello fotovoltaico• Sensore Crepuscolare e di Presenza• Emissione LED
ApplicazioneIlluminazione pubblica, Aree pe-donali,
Aree residenziali, Esterni industriali
ApplictionsStreet lighting in suspended mode. Great range of mounting heights: 6 - 12 m.
Technical data• Designed, under pressure fused anodized aluminium chassis • Anodized aluminum treatment• Polyester powder paint colour: “Dark Smoke” and embossed RAL 7016 (“Silver” RAL 9006 colour is available on request)• High efficiency PMMA optics • Flat protective diffuser with 4 mm extra clear tempered glass• Suitable for support cable with diameter from 6 to 12 mm • IP66 Grade of protection, mounted • Impact resistance: IK09 • Insulation Class I or II • TCS - Thermal Cooling System • Full cut-off • Stainless steel or insulated outside screws
• Photobiological safety, refer to EN 62471:2008 and IEC/TI 62471:2009 • Made in Italy - EU - CE mark • Dimensions 350x350xh80 mm, weight 5 Kg.
Advantages • Wide range of optics, power and colour • Driver is included in the body • Functional versions: OF - DM - DMP - TLC - VDC • Automatic temperature control • Dimmable/Programmable • Quick cleaning and minimal main-tenance • Option of supplementary protection against line surges • Long life reliability
MontaggioFixing suspended to the steel cable by a furnished mechanical interface.
We Install thiese products only under commission or tenders or for startups.60
PIEDINO
ALUKS
ApplicationsHighways, Roads, Streets, Motorways, Parking lots, roundabouts, Industrial are-as, Storage areas.Suggested installation height: 6 - 12 m.
Technical Data• LED designed pressure fused aluminium body• High efficiency PMMA optics• Flat protective diffuser with 4 mm extra clear tempered glass for security• Anodized aluminum treatment• Polyester powder painting, color “Sil-ver” RAL 9006 embossed• Grade of protection IP66• Impact resistance IK09• Insulation Class I or II• TCS - Thermal Cooling System• Total cut-off• Stainless steel screws• CB international standards certification• Photobiological safety refer to EN 62471:2008 and IEC/TI 62471:2009
• Made in Italy - EU - CE mark• Overall dimensions: 580 x 270 x 70mm. Weight: 5 Kg
Advantages• High performance and maximum mana-gement benefits• Wide range of white tonality and high color rendering “Urban Renaissance by Litek”• Functional versions: OF - DM - DMP - TLC - VDC• Automatic temperature control• Dimmable/Programmable• Quick cleaning and minimal mainte-nance• Option of supplementary protection against power-line surges• Long-life reliability
MountingTop post d. 60/76 mmVertical or horizontalOn post or wall
ApplicationsHighways, Roads, Streets, Motorways, Parking lots, roundabouts, Industrial areas, Storage areas.Suggested installation height 6 - 11 m.
Technical Data• LED designed pressure fused aluminium body• High efficiency PMMA optics• Flat protective diffuser with 5 mm extra clear tempe-red glass for security• Anodized aluminum treatment• Polyester powder paint colour, “Silver” with embossed RAL 9006 (“Dark Smoke” RAL 7016 colour is available
on request)• Grade of protection IP65• Insulation Class I or II• TCS - Thermal Cooling System• Full cut-off• Stainless steel screws• Photobiological safety refer to EN 62471:2008 and IEC/TI 62471:2009• Made in Italy - EU - CE mark• Overall dimensions: 700 x 350 x 90 mm. Weight: 9.5 kg
Advantages• High performance and maximum management benefits• Wide range of white tonality and high color rendering “Urban Re-naissance by Litek”• Functional versions: OF - DM - DMP - TLC - VDC• Automatic temperature control
• Dimmable/Programmable• Self-cleaning and extremely reduced maintenance• Option of supplementary protection against power-line surges• Long-life reliability
MountingTop post d. 60/76 mmVertical or horizontalOn post or wall
We Install thiese products only under commission or tenders or for startups.61
62
63
M A R K E T I N G , R E S E A R C H A N D D E S I G N R & D D E PA R T M E N T
PAT E N T O F F I C E B U I S N E S S A N A LY S I S
The Cleantech Incubator is a buisness incubator that is born from the expe-rience of professionals dedicated to the world of cleantech technologies, from the sustainable mobility field, the production of renewable energy and its efficient use, home automation and web platforms for the marketing of eco-friendly products. The Incubator’s mission is to provide all necessary services to innovative business ideas through regular support, bureau-cratic and legal imperative to set up a start up. The professional skills of The Cleantech Incubator also ensure the growing of the start up by the provision of its offices to work in co-working, a room for development of prototypes and
I n P a r t n e r s h i p W i t h
the advice of profes-sionals and experts in the industry for equity research and training on team management techniques. The activi-ties of The Cleantech Incubator are not only addressed to customers, but for the effect of the experience gained in clean technologies. The incubator itself has patents and start-ups. The research, analyzes and studies carried out in the proposition of the goods and services of their innovative start-ups have so pushed the Cleantech Incubator to create partnerships with representatives of the eco-sector compa-nies, whose synergy has developed a range of products used to market on a large scale.
64
E N E R G Y P R O D U C T I O N b y r e n e w a b l e s o r s i m i l a r
H O M E A U T O M AT I O N A N D E N E R G Y E F F I C I E N C Y
D I G I TA L
P r o d u c t s f o r
P r o d u c t s f o r
P r o d u c t s a n d s e r v i c i e s
C L E A N M O B I L I T Y
E N E R G Y E F F I C I E N C Y U S E
E C O - S H O P P I N G
P r o d u c t s f o r
P r o d u c t s f o r
E - C o m m e r c e
65
66
67
ER International S.r.l.sSede operativaVia Ignazio Silone, 10
60035 Jesi (AN)C.F.|P.IVA: 02720540422
mail: [email protected]