Upload
vuonglien
View
241
Download
1
Embed Size (px)
Citation preview
29
KugelhähneTrinkwasser-Kugelhähne
Heizungs- und Gas-Kugelhähne
Ball Valves Drinking Water Ball Valves
Heating and Gas Ball Valves
30
Art.-Nr./Bezeichnung
Art.-No./Article
Abmessung
Dimension
Baulänge
Length
Art.-Nr. 1446
Kugelhahn UNIWATER, DIN EN 13828
aus Messing CW 617 N, mit Tefl on®-Dichtung
beiderseits Innengewinde, mit ISO-T-Griff, grün
mit vollem Durchgang, mit zylindrischer Bohrung
PN 10, mit DVGW-Zulassung
Ball valve UNIWATER, DIN EN 13828
hot pressed brass CW 617 N, with Tefl on®-seal
female thread both ends, with ISO-T handle, green
full passage with cylindric drilling
PN 10, with DVGW-approval
1/2“
3/4“
1“
1 1/4“
1 1/2“
2“
75
80
90
110
120
140
Gewicht g
Weight g
230
380
560
990
1.590
2.670
Trinkwasser-Kugelhähne
Drinking Water Ball Valves
Art.-Nr. 1447
Kugelhahn UNIWATER, DIN EN 13828
aus Messing CW 617 N, mit Tefl on®-Dichtung
beiderseits Innengewinde, mit Flügelgriff, grün
mit vollem Durchgang, mit zylindrischer Bohrung
PN 10, mit DVGW-Zulassung
Ball valve UNIWATER, DIN EN 13828
hot pressed brass CW 617 N, with Tefl on®-seal
female thread both ends, with butterfl y handle, green
full passage with cylindric drilling
PN 10, with DVGW-approval
1/2“
3/4“
1“
1 1/4“
220
350
550
980
75
80
90
110
Art.-Nr. 1442
System-Kugelhahn UNIWATER, DIN EN 13828
aus Messing CW 617 N, mit Tefl on®-Dichtung
beiderseits Außengewinde, mit Stahlhebel, grün
ohne Entleerung, mit vollem Durchgang,
mit zylindrischer Bohrung, PN 10, mit DVGW-Zulassung
System-ball valve UNIWATER, DIN EN 13828
hot pressed brass CW 617 N, with Tefl on®-seal
male thread both ends, with steel lever, green
without discharge, full passage with cylindric drilling
PN 10, with DVGW-approval
3/4“
1“
1 1/4“
1 1/2“
1 3/4“
2 3/8“
75
85
98
115
127
151
250
380
640
960
1.610
2.620
Art.-Nr. 1443
System-Kugelhahn UNIWATER, DIN EN 13828
aus Messing CW 617 N, mit Tefl on®-Dichtung
beiderseits Außengewinde, mit ISO-T-Griff, grün
ohne Entleerung, mit vollem Durchgang,
mit zylindrischer Bohrung, PN 10, mit DVGW-Zulassung
System-ball valve UNIWATER, DIN EN 13828
hot pressed brass CW 617 N, with Tefl on®-seal
male thread both ends, with ISO-T handle, green
without discharge, full passage with cylindric drilling
PN 10, with DVGW-approval
75
85
98
115
127
151
240
400
650
940
1.550
2.610
Art.-Nr. 1449
Kugelhahn UNIWATER, DIN EN 13828
aus Messing CW 617 N, mit Tefl on®-Dichtung
beiderseits Innengewinde, mit Stahlhebel, grün
mit vollem Durchgang, mit zylindrischer Bohrung
PN 10, 1/2“ bis 2“ mit DVGW-Zulassung
Ball valve UNIWATER, DIN EN 13828
hot pressed brass CW 617 N, with Tefl on®-seal
female thread both ends, with steel lever, green
full passage with cylindric drilling
PN 10, 1/2“-2“ with DVGW-approval
3/8“
1/2“
3/4“
1“
1 1/4“
1 1/2“
2“
2 1/2“
3“
4“
60
75
80
90
110
120
140
185
210
250
160
250
370
570
1.030
1.580
2.650
4.420
7.440
13.200
DN 15 x
DN 20 x
DN 25 x
DN 32 x
DN 40 x
DN 50 x
3/4“
1“
1 1/4“
1 1/2“
1 3/4“
2 3/8“
DN 15 x
DN 20 x
DN 25 x
DN 32 x
DN 40 x
DN 50 x
31
Art.-Nr. 1444
System-Kugelhahn UNIWATER, DIN EN 13828
aus Messing CW 617 N, mit Tefl on®-Dichtung
beiderseits Außengewinde, mit Flügelgriff, grün
ohne Entleerung, mit vollem Durchgang,
mit zylindrischer Bohrung, PN 10, mit DVGW-Zulassung
System-ball valve UNIWATER, DIN EN 13828
hot pressed brass CW 617 N, with Tefl on®-seal
male thread both ends, with butterfl y handle, green
without discharge, full passage with cylindric drilling
PN 10, with DVGW-approval
75
85
98
115
230
360
620
920
Art.-Nr./Bezeichnung
Art.-No./Article
Abmessung
Dimension
Baulänge
Length
Art.-Nr. 1437
System-Kugelhahn UNIWATER, DIN EN 13828
aus Messing CW 617 N, mit Tefl on®-Dichtung
beiderseits Außengewinde, mit Stahlhebel, grün
mit Entleerung, mit vollem Durchgang,
mit zylindrischer Bohrung PN 10, mit DVGW-Zulassung
System-ball valve UNIWATER, DIN EN 13828
hot pressed brass CW 617 N, with Tefl on®-seal
male thread both ends, with steel lever, green
with discharge, full passage with cylindric drilling
PN 10, with DVGW-approval
75
85
98
115
127
151
Gewicht g
Weight g
280
420
670
990
1.640
2.660
Art.-Nr. 1438
System-Kugelhahn UNIWATER, DIN EN 13828
aus Messing CW 617 N, mit Tefl on®-Dichtung
beiderseits Außengewinde, mit ISO-T-Griff, grün
mit Entleerung, mit vollem Durchgang,
mit zylindrischer Bohrung PN 10, mit DVGW-Zulassung
System-ball valve UNIWATER, DIN EN 13828
hot pressed brass CW 617 N, with Tefl on®-seal
male thread both ends, with ISO-T handle, green
with discharge, full passage with cylindric drilling
PN 10, with DVGW-approval
280
440
690
980
1.530
2.620
75
85
98
115
127
151
Art.-Nr. 1439
System-Kugelhahn UNIWATER, DIN EN 13828
aus Messing CW 617 N, mit Tefl on®-Dichtung
beiderseits Außengewinde, mit Flügelgriff, grün
mit Entleerung, mit vollem Durchgang,
mit zylindrischer Bohrung PN 10, mit DVGW-Zulassung
System-ball valve UNIWATER, DIN EN 13828
hot pressed brass CW 617 N, with Tefl on®-seal
male thread both ends, with butterfl y handle, green
with discharge, full passage with cylindric drilling
PN 10, with DVGW-approval
75
85
98
115
270
400
650
950
Art.-Nr. 4215-4254
System-Kugelhahn UNIWATER, DIN EN 13828
aus Messing CW 617 N, mit Tefl on®-Dichtung
mit beidseitigem Außengewinde
mit 2 x Viega-Profi press®-Verschraubungen
ohne Entleerung, mit Stahlhebel, grün
System-ball valve UNIWATER, DIN EN 13828
hot pressed brass CW 617 N, with Tefl on®-seal
male thread both ends
with 2 x Viega-Profi press®-Screws
without discharge, with steel lever, green
Trinkwasser-Kugelhähne
Drinking Water Ball Valves
3/4“
1“
1 1/4“
1 1/2“
DN 15 x
DN 20 x
DN 25 x
DN 32 x
3/4“
1“
1 1/4“
1 1/2“
1 3/4“
2 3/8“
DN 15 x
DN 20 x
DN 25 x
DN 32 x
DN 40 x
DN 50 x
3/4“
1“
1 1/4“
1 1/2“
1 3/4“
2 3/8“
DN 15 x
DN 20 x
DN 25 x
DN 32 x
DN 40 x
DN 50 x
3/4“
1“
1 1/4“
1 1/2“
DN 15 x
DN 20 x
DN 25 x
DN 32 x
140
162
179
201
241
255
390
590
960
1.370
2.270
3.690
3/4“
1“
1 1/4“
1 1/2“
1 3/4“
2 3/8“
DN 15 x
DN 20 x
DN 25 x
DN 32 x
DN 40 x
DN 50 x
32
Art.-Nr. 4415-4435
System-Kugelhahn UNIWATER, DIN EN 13828
aus Messing CW 617 N, mit Tefl on®-Dichtung
mit beidseitigem Außengewinde
mit 2 x Viega-Profi press®-Verschraubungen
ohne Entleerung, mit Flügelgriff, grün
System-ball valve UNIWATER, DIN EN 13828
hot pressed brass CW 617 N, with Tefl on®-seal
male thread both ends
with 2 x Viega-Profi press®-Screws
without discharge, with butterfl y handle, green
Art.-Nr./Bezeichnung
Art.-No./Article
Abmessung
Dimension
Baulänge
Length
Gewicht g
Weight g
Trinkwasser-Kugelhähne
Drinking Water Ball Valves
Art.-Nr. 3715-3754
System-Kugelhahn UNIWATER, DIN EN 13828
aus Messing CW 617 N, mit Tefl on®-Dichtung
mit beidseitigem Außengewinde
mit 2 x Viega-Profi press®-Verschraubungen
mit Entleerung, mit Stahlhebel, grün
System-ball valve UNIWATER, DIN EN 13828
hot pressed brass CW 617 N, with Tefl on®-seal
male thread both ends
with 2 x Viega-Profi press®-Screws
with discharge, with steel lever, green
Art.-Nr. 3815-3854
System-Kugelhahn UNIWATER, DIN EN 13828
aus Messing CW 617 N, mit Tefl on®-Dichtung
mit beidseitigem Außengewinde
mit 2 x Viega-Profi press®-Verschraubungen
mit Entleerung, mit ISO-T-Griff, grün
System-ball valve UNIWATER, DIN EN 13828
hot pressed brass CW 617 N, with Tefl on®-seal
male thread both ends
with 2 x Viega-Profi press®-Screws
with discharge, with ISO-T handle, green
Art.-Nr. 3915-3935
System-Kugelhahn UNIWATER, DIN EN 13828
aus Messing CW 617 N, mit Tefl on®-Dichtung
mit beidseitigem Außengewinde
mit 2 x Viega-Profi press®-Verschraubungen
mit Entleerung, mit Flügelgriff, grün
System-ball valve UNIWATER, DIN EN 13828
hot pressed brass CW 617 N, with Tefl on®-seal
male thread both ends
with 2 x Viega-Profi press®-Screws
with discharge, with butterfl y handle, green
Art.-Nr. 4315-4354
System-Kugelhahn UNIWATER, DIN EN 13828
aus Messing CW 617 N, mit Tefl on®-Dichtung
mit beidseitigem Außengewinde
mit 2 x Viega-Profi press®-Verschraubungen
ohne Entleerung, mit ISO-T-Griff, grün
System-ball valve UNIWATER, DIN EN 13828
hot pressed brass CW 617 N, with Tefl on®-seal
male thread both ends
with 2 x Viega-Profi press®-Screws
without discharge, with ISO-T handle, green
140
162
179
201
241
255
390
590
960
1.370
2.270
3.690
3/4“
1“
1 1/4“
1 1/2“
1 3/4“
2 3/8“
DN 15 x
DN 20 x
DN 25 x
DN 32 x
DN 40 x
DN 50 x
140
162
179
201
370
580
930
1.340
3/4“
1“
1 1/4“
1 1/2“
DN 15 x
DN 20 x
DN 25 x
DN 32 x
140
162
179
201
241
255
400
610
960
1.390
2.270
3.740
3/4“
1“
1 1/4“
1 1/2“
1 3/4“
2 3/8“
DN 15 x
DN 20 x
DN 25 x
DN 32 x
DN 40 x
DN 50 x
140
162
179
201
241
255
410
640
1.020
1.400
2.250
3.740
3/4“
1“
1 1/4“
1 1/2“
1 3/4“
2 3/8“
DN 15 x
DN 20 x
DN 25 x
DN 32 x
DN 40 x
DN 50 x
140
162
179
201
390
610
970
1.380
3/4“
1“
1 1/4“
1 1/2“
DN 15 x
DN 20 x
DN 25 x
DN 32 x
33
Art.-Nr./Bezeichnung
Art.-No./Article
Abmessung
Dimension
Baulänge
Length
Art.-Nr. 1440
Gas-Kugelhahn, matt verchromt
DIN EN 331, Gehäuse aus Messing CW 617 N
Schwer-Modell MOP 5
Stahlhebel, verzinkt, mit gelbem Kunststoffüberzug
mit DVGW-Zulassung
Gas ball valve, rough chrome-plated
DIN EN 331, body hot pressed brass MS 58
heavy type MOP 5
galvanized steel lever, yellow plastic coated
with DVGW-approval
3/8“
1/2“
3/4“
1“
1 1/4“
1 1/2“
2“
59
59
67
80
96
106
131
Gewicht g
Weight g
170
200
300
500
740
1.140
1.860
Art.-Nr. 1450
Kugelhahn aus Pressmessing MS 58, matt verchromt
Schwer-Modell, mit vollem zylindrischen Durchgang
Stahlhebel, formgepresst, rot lackiert
PN 50
Ball valve, hot pressed brass MS 58, rough chrome-plated
heavy type, with full cylindric passage
profi led steel lever, red
PN 50
1/4“
3/8“
1/2“
3/4“
1“
1 1/4“
1 1/2“
2“
2 1/2“
3“
4“
38
38
56
68
80
90
100
125
135
170
195
140
140
220
360
560
780
1.210
2.020
3.790
5.370
9.250
Art.-Nr. 1452
Kugelhahn UNIVERS, matt verchromt
Normal-Modell aus Pressmessing MS 58
mit vollem zylindrischen Durchgang
Stahlhebel, verzinkt, mit rotem Kunststoffüberzug
PN 30
Ball valve UNIVERS, rough chrome-plated
standard type, hot pressed brass MS 58
with full cylindirc passage
galvanized steel lever, red plastic coated
PN 30
41
50
56
66
74
88
102
127
144
120
180
270
430
570
850
1.360
2.430
3.670
Art.-Nr. 1454
Kugelhahn UNIVERS, matt verchromt
Normal-Modell aus Pressmessing MS 58
mit vollem zylindrischen Durchgang
mit Flügelgriff
PN 30
Ball valve UNIVERS, rough chrome-plated
standard type, hot pressed brass MS 58
with full cylindric passage
with butterfl y handle
PN 30
3/8“
1/2“
3/4“
1“
1 1/4“
41
50
56
66
74
90
150
230
380
510
3/8“
1/2“
3/4“
1“
1 1/4“
1 1/2“
2“
2 1/2“
3“
Heizungs- und Gas-Kugelhähne
Heating and Gas Ball Valves
34
Art.-Nr. 1455
Kugelhahn aus Pressmessing MS 58, matt verchromt
mit vollem Durchgang
einerseits Innengewinde, andererseits Außengewinde
Stahlhebel, formgepresst, rot lackiert
PN 30
Ball valve, hot pressed brass MS 58, rough chrome-plated
with full passage
female thread/male thread, profi led steel lever, red
PN 30
1/4“
3/8“
1/2“
3/4“
1“
1 1/4“
1 1/2“
2“
51
39
50
58
67
78
92
107
100
130
190
260
430
590
840
1.390
Art.-Nr. 1485
Kugelhahn aus Pressmessing MS 58, matt verchromt
mit vollem Durchgang
einerseits Innengewinde, andererseits Außengewinde
mit Flügelgriff
PN 30
Ball valve, hot pressed brass MS 58, rough chrome-plated
with full passage
female thread/male thread
with butterfl y handle
PN 30
3/8“
1/2“
3/4“
1“
1 1/4“
39
50
58
67
78
Art.-Nr. 1456
Kugelhahn aus Pressmessing MS 58, matt verchromt
mit Anschlussverschraubung
einerseits Innengewinde, andererseits Außengewinde
mit Flügelgriff
Ball valve, hot pressed brass MS 58, rough chrome-plated
with connection union
female thread/male thread
with butterfl y handle
1/2“
3/4“
1“
1 1/4“
70
80
89
130
190
300
630
680
Art.-Nr. 1457
Kugelhahn aus Pressmessing MS 58, matt verchromt
mit vollem Durchgang, mit Entleerung
Stahlhebel, verzinkt, mit rotem Kunststoffüberzug
PN 30
Ball valve, hot pressed brass MS 58, rough chrome-plated
with full passage
with discharge
galvanized steel lever, red plastic coated
PN 30
54
60
74
82
93
108
230
320
480
630
1.000
1.430
Art.-Nr. 1467
Kugelhahn aus Pressmessing MS 58, matt verchromt
mit vollem Durchgang, mit Entleerung
mit Flügelgriff
PN 30
Ball valve, hot pressed brass MS 58, rough chrome-plated
with full passage
with discharge
with butterfl y handle
PN 30
1/2“
3/4“
1“
1 1/4“
54
60
74
82
200
290
460
680
110
160
290
360
560
1/2“
3/4“
1“
1 1/4“
1 1/2“
2“
Art.-Nr./Bezeichnung
Art.-No./Article
Abmessung
Dimension
Baulänge
Length
Gewicht g
Weight g
Heizungs- und Gas-Kugelhähne
Heating and Gas Ball Valves
35
Art.-Nr./Bezeichnung
Art.-No./Article
Abmessung
Dimension
Baulänge
Length
Gewicht g
Weight g
Art.-Nr. 1460
Mini-Kugelhahn, verchromt
aus Sechskant-Stangenmaterial
mit 2 x Innengewinde
mit Flügelgriff
PN 10
Mini-ball valve, chrome-plated
hexagon brass
female threads
with butterfl y handle
PN 10
1/4“
3/8“
1/2“
39
40
45
110
110
120
Art.-Nr. 1465
Mini-Kugelhahn, verchromt
aus Sechskant-Stangenmaterial
mit 1x Innen- und 1x Außengewinde
mit Flügelgriff
PN 10
Mini-ball valve, chrome-plated
hexagon brass
female thread/male thread
with butterfl y handle
PN 10
1/4“
3/8“
1/2“
39
40
45
Art.-Nr. 1470
Kugelhahn aus Pressmessing MS 58, matt verchromt
mit reduziertem Durchgang
Hebel aus Alu-Druckguss
PN 20
Ball valve, hot pressed brass MS 58, rough chrome-plated
with reduced passage
lever, Alu-diecasting
PN 20
3/8“
1/2“
3/4“
1“
1 1/4“
1 1/2“
2“
2 1/2“
3“
4“
50
46
53
62
70
82
93
115
139
157
130
120
180
280
420
540
880
2.290
3.380
6.360
Art.-Nr. 1471
Kugelhahn aus Pressmessing MS 58, matt verchromt
mit reduziertem Durchgang
mit Flügelgriff
PN 20
Ball valve, hot pressed brass MS 58, rough chrome-plated
with reduced passage
with butterfl y handle
PN 20
Art.-Nr. 1472
Lötkugelhahn aus Pressmessing MS 58, matt verchromt
mit vollem Durchgang, zum Weichlöten für Kupferrohr
Stahlhebel, verzinkt, mit rotem Kunststoffüberzug
Ball valve, hot pressed brass MS 58, rough chrome-plated
with full passage, with soldering ends for soft soldering
for copper tubes
galvanized steel lever, red plastic coated
15 mm
18 mm
22 mm
28 mm
35 mm
53
60
70
85
98
180
210
350
480
720
100
90
110
3/8“
1/2“
3/4“
1“
50
46
53
62
130
120
180
300
Heizungs- und Gas-Kugelhähne
Heating and Gas Ball Valves
36
Art.-Nr. 1473
Lötkugelhahn aus Pressmessing MS 58, matt verchromt
mit vollem Durchgang, zum Weichlöten für Kupferrohr
mit Flügelgriff
Ball valve, hot pressed brass MS 58, rough chrome-plated
with full passage, with soldering ends for soft soldering
for copper tubes
with butterfl y handle
15 mm
18 mm
22 mm
28 mm
53
60
70
85
140
170
280
430
Art.-Nr. 1475
Pumpenkugelhahn
zum Direktanschluss an die Umwälzpumpe
10 Bar, 120°
Ball valve for heating pumps
for direct assembly at the circulating pump
10 bar, 120°
1“ 47
Art.-Nr. 1476
Pumpenkugelhahn, matt verchromt
Gehäuse aus Pressmessing MS 58
ohne Schwerkraftbremse
Ball valve for heating pumps, rough chrome-plated
body hot pressed brass MS 58
without integrated check valve
1“ 76 320
Art.-Nr. 1482
Kugelhahn mit Press-Enden, aus Pressmessing MS 58
mit vollem Durchgang, mit Stahlhebel
zum Direktverpressen von Kupfer- bzw. Edelstahlrohren
PN 30
Ball valves with direct press ends, hot pressed brass MS 58
with full passage, with steel lever
suitable for copper or stainless steel tubes
PN 30
15 mm
18 mm
22 mm
28 mm
82
84
100
105
150
190
240
440
200
Art.-Nr./Bezeichnung
Art.-No./Article
Abmessung
Dimension
Baulänge
Length
Gewicht g
Weight g
Art.-Nr. 1477
Pumpenkugelhahn, matt verchromt
Gehäuse aus Pressmessing MS 58
mit Schwerkraftbremse
Ball valve for heating pumps, rough chrome-plated
body hot pressed brass MS 58
with integrated check valve
1“ 76 340
Heizungs- und Gas-Kugelhähne
Heating and Gas Ball Valves
37
15 mm
18 mm
22 mm
28 mm
82
84
100
105
140
170
290
430
Art.-Nr. 1458
ISO-T-Kugelhahn aus Pressmessing MS 58
mit verlängertem T-Griff, rot
voll isolierbar
PN 30, 120°C
ISO-T-ball valve, hot pressed brass MS 58
with extended T-handle, red
complete isolation possible
PN 30, 120°C
3/8“
1/2“
3/4“
1“
1 1/4“
1 1/2“
2“
41
49
56
67
74
88
103
Art.-Nr. 1478
ISO-T-Pumpenkugelhahn aus Pressmessing MS 58
mit verlängertem T-Griff, rot
voll isolierbar
PN 30, 120°
ISO-T-ball valve for heating pumps
hot pressed brass MS 58
with extended T-handle, red
complete isolation possible
PN 30, 120°
1‘‘
1 1/4‘‘
1 1/4“ x 1“
93
101
91
530
750
560
Art.-Nr. 1480
Bimetall-Thermometer
passend zu ISO-T-Kugelhähne
mit Clip zum nachträglichen Einbau
(geeignet ab 1“)
Bimetal-Thermometer
suitable for ISO-T-ball valves
with clip for later assembly
(suitable from 1“onwards)
30
110
160
270
400
500
830
1.280
Art.-Nr./Bezeichnung
Art.-No./Article
Abmessung
Dimension
Baulänge
Length
Gewicht g
Weight g
Art.-Nr. 1479
ISO-T-Pumpenkugelhahn aus Pressmessing MS 58
mit verlängertem T-Griff, rot
voll isolierbar
mit Schwerkraftbremse, mit Aufstellvorrichtung
PN 30
ISO-T-ball valve for heating pumps
hot pressed brass MS 58
with extended T-handle, red
complete isolation possible
with integrated check valve, with open position fi xture
PN 30
92
110
93,5
530
760
580
Art.-Nr. 1488
Kugelhahn mit Press-Enden, aus Pressmessing MS 58
mit vollem Durchgang, mit verlängertem T-Griff
zum Direktverpressen von Kupfer- bzw. Edelstahlrohren
PN 30
Ball valves with direct press ends, hot pressed brass MS 58
with full passage, with extended T-handle
suitable for copper or stainless steel tubes
PN 30
1‘‘
1 1/4‘‘
1 1/4“ x 1“
Heizungs- und Gas-Kugelhähne
Heating and Gas Ball Valves
38
Gehäuse: Messing CW 617 N mit vollem Durchgang
Kugel: Messing CW 614 N, verchromt
mit vollem zylindrischen Durchgang
Dichtungen: PTFE (an Kugel und Spindel)
Spindel: Messing CW 614 N roh
mit nachziehbarer Stopfbuchse
Griff: Stahlhebel / ISO-T-Griff / Flügelgriff grün,
auch in rot und blau erhältlich
Temperatur: bis 150°C (siehe Diagramm)
Druck: bis 50 bar (siehe Diagramm)
Body: brass CW 617 N with full passage
Ball: brass CW 614 N, chrome plated
full passage with cylindric drilling
Seals: PTFE (at ball and spindle)
Spindle: brass CW 614 N raw
with adjustable packing box
Handle: steel lever / ISO-T handle / butterfl y handle, green,
also available in red and blue
Temerature: up to 150°C (see diagram)
Pressure: up to 50 bar (see diagram)
Abmessung
Dimension
3/8“
1/2“
3/4“
1“
1 1/4“
1 1/2“
2“
2 1/2“
3“
4“
DN
10
15
20
25
32
40
50
65
80
100
PN
50
50
40
40
40
40
40
20
20
20
L
60
75
80
90
110
120
140
185
210
250
LM
30
37,5
40
45
55
60
70
95
105
125
H
36
46
50
55
72
75
85
100
114
120
LH
84
84
84
100
117
136
136
163
225
225
Gewicht g
Weight g
160
235
350
560
1.000
1.590
2.700
4.460
7.390
13.200
SW
21
25
31
38
48
54
66
82
97
125
GT
12
15
16
20
21
24
27
33
38
40
LH
SW
H
GT
LM
L
DN
Technisches Datenblatt Art.-Nr. 1449
DIN EN-Kugelhahn UNIWATER
gemäß DIN EN 13828
Technical data sheet Art.-No. 1449
DIN EN ball valve UNIWATER
according to DIN EN 13828
Druck/Temperatur-Diagramm
Pressure/temperature diagram
Druckverlust-Diagramm
Pressure loss diagram
Technische Änderungen und Irrtümer vorbehalten. Technical changes and errors reserved.
39
Gehäuse: Messing CW 617 N mit vollem Durchgang
Kugel: Messing CW 614 N, verchromt
mit vollem zylindrischen Durchgang
Dichtungen: PTFE (an Kugel und Spindel)
Spindel: Messing CW 614 N roh
mit nachziehbarer Stopfbuchse
Griff: Stahlhebel / ISO-T-Griff / Flügelgriff grün,
auch in rot und blau erhältlich
Temperatur: bis 150°C (siehe Diagramm)
Druck: bis 50 bar (siehe Diagramm)
Body: brass CW 617 N with full passage
Ball: brass CW 614 N, chrome plated
full passage with cylindric drilling
Seals: PTFE (at ball and spindle)
Spindle: brass CW 614 N raw
with adjustable packing box
Handle: steel lever / ISO-T handle / butterfl y handle, green,
also available in red and blue
Temerature: up to 150°C (see diagram)
Pressure: up to 50 bar (see diagram)
Abmessung
Dimension
3/4“
1“
1 1/4“
1 1/2“
1 3/4“
2 3/8“
DN
15
20
25
32
40
50
PN
50
40
40
40
40
40
L
75
85
98
115
127
151
H
46
50
56
72
75
86
LH
84
84
98
117
137
137
Gewicht g
Weight g
280
420
670
990
1.640
2.660
Technisches Datenblatt Art.-Nr. 1442
System-Kugelhahn UNIWATER
Der Universelle für alle Pressverbindungen
Technical data sheet Art.-No. 1442
System ball valve UNIWATER
The universal for all press fi ttings
Druck/Temperatur-Diagramm
Pressure/temperature diagram
Druckverlust-Diagramm
Pressure loss diagram
Technische Änderungen und Irrtümer vorbehalten. Technical changes and errors reserved.
40
Technisches Datenblatt Art.-Nr. 1458/1478/1479
ISO-T-Kugelhahn
Technical data sheet Art.-No. 1458/1478/1479
ISO-T ball valve
Gehäuse: Messing MS 58
Kugel: Messing MS 58 verchromt
Dichtungen Kugel: PTFE
Spindel: Messing MS 58 verchromt
mit nachziehbarer Stopfbuchse
Spindelabdichtung: PTFE
Griff: Kunststoff rot mit weißem Clip
Abmessung
Dimension
3/8“
1/2“
3/4“
1“
1 1/4“
1 1/2“
2“
1“ x 1“
1 1/4“ x 1“
1 1/4“ x 1 1/4“
1“ x 1“
1 1/4“ x 1“
1 1/4“ x 1 1/4“
d
10
14
20
24
30
35
47
24
23
30
24
24
30
L
41
49
56
67
74
88
103
93
91
101
92
93,5
110,5
GT
9
14
13
14
15
17
18
16
15
17
15
15
18
V
61
61
83
83
83
100
100
83
83
82
83
83
83
H
52
56
74
78
82
93
99
78
78
88
81
80
83
h
39
44
54
60
66
78
77
62
65
70
61
61
67
Gewicht g
Weight g
110
160
270
400
500
830
1.280
530
560
750
530
580
760
SW
20
26
31
39
48
54
69
39
48
47
38
48
48
Art.-Nr. 1458
Art.-Nr. 1478
Art.-Nr. 1479
V
dD
L
h
H
GT
SW
V
dD
L
h
H
GT
SW
V
dD
L
h
H
GT
SW
1458 1478 1479
Body: brass MS 58
Ball: brass MS 58 chrome plated
Seals at ball: PTFE
Spindle: brass MS 58 chrome plated
with adjustable packing box
Seal of spindle: PTFE
Handle: plastic red with white clip
Technische Änderungen und Irrtümer vorbehalten. Technical changes and errors reserved.
41
ISO-T-Kugelhahn 1458
■ verlängerter Bedienungsgriff
■ voll isolierbar
■ Eignung für Heizungsanlagen
■ beständig für Kalt- und Warmwasser,
Mineralöle u.v.m.
■ temperaturbeständig bis 120°C
■ druckbeständig bis 30 bar
ISO-T-Pumpenkugelhahn 1478
■ zum direkten Anschluss
an die Umwälzpumpe
■ ohne Schwerkraftbremse
ISO-T-Pumpenkugelhahn 1479
■ zum direkten Anschluss an die Umwälzpumpe
■ mit Schwerkraftbremse (SKB)
■ mit Aufstellvorrichtung
Der Pumpenkugelhahn mit SKB muss vor
der Umwälzpumpe eingebaut werden.
NEU: Die Verstellung der Schwerkraftbremse erfolgt
über die Kugelverstellung. Bei Hebelstellung 45°
öffnet sich die Schwerkraftbremse, dadurch ist die
Verstellschraube nicht mehr erforderlich.
ISO-T-Pumpenkugelhahn-Set
Das ISO-Pumpenkugelhahn-Set beinhaltet alle
notwendigen Komponenten, die für die Installation
einer Heizungspumpe erforderlich sind – inklusive
Überwurfmuttern und Dichtungen:
1 ISO-T-Pumpenkugelhahn 1478
Abmessung 1“ x 1“
1 ISO-T-Pumpenkugelhahn 1479
Abmessung 1“ x 1“
1 ISO-T-Kugelhahn 1458
Abmessung 1“
2 Bimetall-Thermometer 1480
2 TG-Überwurfmuttern
Abmessung 1“ x 1 1/2“
2 Dichtungen
Abmessung 1 1/2“
ISO-T-Ball Valve Set
The ISO-T-ball valve set comprises all necessary
components that are needed for installation of a
circulation pump – including malleable iron screwed
caps and seals:
1 ISO-T-pump ball valve 1478
dimension 1“ x 1“
1 ISO-T-pump ball valve 1479
dimension 1“ x 1“
1 ISO-T-ball valve 1458
dimension 1“
2 bimetal thermometers 1480
2 malleable iron screwed caps
dimension 1“ x 1 1/2“
2 seals
dimension 1 1/2“
Bimetall-Thermometer 1480
■ Bimetall-Thermometer mit Clip
■ zum nachträglichen Einbau
ISO-T-Ball Valve 1458
■ extended operating handle
■ fully isolable
■ suitable for heating systems
■ resistant for cold and hot water, mineral oil
and others
■ temperature resistant up to 120°C
■ pressure resistant up to 30 bar
ISO-T-Pump Ball Valve 1478
■ for direct connection to the circulation pump
■ without non return valve
ISO-T-Pump Ball Valve 1479
■ for direct connection to the circulation pump
■ with adjustable non return valve
The pump ball valve with non return valve must be
mounted in front of the circulation pump.
NEW: The adjusting of the non return valve is made
by ball adjusting. At handle position 45°, the non
return valve opens, so the adjusting screw is not
necessary.
Bimetal Thermometers 1480
■ bimetal thermometers with clip
■ for additional mounting
Technische Änderungen und Irrtümer vorbehalten. Technical changes and errors reserved.
42
Technisches Datenblatt Art.-Nr. 1440
Gas-Kugelhahn, Schwermodell
Technical data sheet Art.-No. 1440
Gas ball valve, heavy type
■ vielfältige Einsatzmöglichkeiten in Industrie und Handwerk
■ Eignung für Gasanlagen
■ Kennzeichnung nach DVGW-G DIN EN 331
Gehäuse (1): Messing CW 617 N
Einschraubteil (2): Messing CW 617 N
Kugel (3): Messing CW 614 N
Dichtungen (4): PTFE
Spindel (5): Messing CW 614 N
O-Ringe (6): Viton
Befestigungsschraube (7): Messing CW 614 N
Hebel (8): Stahl verzinkt
mit gelbem Kunststoffüberzug
Temperatur: von -20°C bis 60°C
Druckklasse: MOP 5
■ versatile applications for industry and trade
■ suitable for gas-systems
■ marking according to DVGW-G DIN EN 331
Body (1): brass CW 617 N
Screw-in part (2): brass CW 617 N
Ball (3): brass CW 614 N
Seals (4): PTFE
Spindle (5): brass CW 614 N
O-Rings (6): Viton
Fixing screw (7): CW 614 N
Lever (8): steel galvanised
with yellow plastic coating
Temperatur: from -20°C up to 60°C
Pressure class: MOP 5
Abmessung
Dimension
3/8“
1/2“
3/4“
1“
1 1/4“
1 1/2“
2“
I
19
16
18
19
24
24
29
L
59
59
67
80
96
106
131
A
96
96
96
125
125
151
151
H
36
40
45
56
63
79
88
B
25
30
38
46
57
70
88
Gewicht g
Weight g
160
200
300
500
760
1.140
1.860
SW
21
25
31
38
47
54
86
Technische Änderungen und Irrtümer vorbehalten. Technical changes and errors reserved.
43
Technisches Datenblatt Art.-Nr. 1450
Kugelhahn aus Messing MS 58
Technical data sheet Art.-No. 1450
Ball valve, brass MS 58
■ vielfältige Einsatzmöglichkeiten in Industrie und Handwerk
■ Eignung für Heizungs- und Druckluftanlagen
■ Kennzeichnung nach TÜV-Vorschrift
■ beständig für Kalt- und Warmwasser, Dampf, Mineralöle u.v.m.
Gehäuse: Messing MS 58 mit vollem Durchgang
Kennzeichnung nach AD-Merkblatt
Kugel: Messing MS 58, verchromt
mit vollem zylindrischen Durchgang
Dichtungen: an Kugel und Spindel PTFE
Spindel: Messing MS 58, verchromt
mit nachziehbarer Stopfbuchse
Griff: Stahlblech, rot einbrenn-lackiert
Temperatur: bis 180°C
Druck: bis 50 bar
Abmessung
Dimension
1/4“
3/8“
1/2“
3/4“
1“
1 1/4“
1 1/2“
2“
2 1/2“
3“
4“
D
9,5
10
15
20
25
32
40
50
65
80
100
I
10
10
14
16,1
18
21
20
25
21
32
26
L
46
46
56
68
80
90
100
125
135
170
195
A
77
77
85
100
117
117
138
160
225
247
315
H
37
37
41
51
59
65
78
89
125
135
165
B
25
25
32
40
48
58
72
80
112
131
172
bar
50
50
50
40
40
40
40
40
25
14
12
SW
19
21
25
32
38
47
54
66
85
96
127
■ versatile applications for industry and trade
■ suitable for heating and compressed-air systems
■ marking according to TÜV regulation
■ resistant for cold and warm water, steam, mineral oils and others
Body: brass MS 58 with full passage
marking according to AD-data sheet
Ball: brass MS 58, chrome-plated
full passage with cylindrical drilling
Seals: at ball and spindle PTFE
Spindle: brass MS 58, chrome-plated
with adjustable packing box
Handle: steel plate, red enamelled
Temperature: up to 180°C
Pressure: up to 50 bar
Druck/Temperatur-Diagramm
Pressure/temperature diagram
Druckverlust-Diagramm
Pressure loss diagram
Technische Änderungen und Irrtümer vorbehalten. Technical changes and errors reserved.
44
■ vielfältige Einsatzmöglichkeiten in Industrie und Handwerk
■ Eignung für Heizungs- und Druckluftanlagen
■ Kennzeichnung nach TÜV-Vorschrift
■ beständig für Kalt- und Warmwasser, Dampf, Mineralöle u.v.m.
Gehäuse: Messing MS 58 mit vollem Durchgang
Kennzeichnung nach AD-Merkblatt
Kugel: Messing MS 58, verchromt
mit vollem zylindrischen Durchgang
Dichtungen: an Kugel und Spindel PTFE
Spindel: Messing MS 58, verchromt
mit nachziehbarer Stopfbuchse
Griff: Stahlblech verzinkt, mit rotem Kunststoffüberzug
bzw. Flügelgriff, Alu-Druckguss (Art.-Nr. 1454)
Temperatur: bis 180°C
Druck: bis 30 bar
Abmessung
Dimension
3/8“
1/2“
3/4“
1“
1 1/4“
1 1/2“
2“
2 1/2“
3“
DN
10
15
20
25
32
40
50
65
80
L
41
50
56
66
74
88
102
127
144
GT
10
11
13
15
15
18
19
24
26
LH
85
98
101
126
126
136
130
205
247
H
38
40
46
55
62
72
81
108
123
D
34
29
36
44
53
63
79
98
117
SW
20
25
31
38
47
54
67
82
96
Gewicht g
Weight g
120
180
270
430
570
850
1.360
2.430
3.670
Druck/Temperatur-Diagramm
Pressure/temperature diagram
Druckverlust-Diagramm
Pressure loss diagram
■ versatile applications for industry and trade
■ suitable for heating and compressed-air systems
■ marking according to TÜV regulation
■ resistant for cold and warm water, steam, mineral oils and others
Body: brass MS 58 with full passage
marking according to AD-data sheet
Ball: brass MS 58, chrome-plated
full passage with cylindrical drilling
Seals: at ball and spindle PTFE
Spindle: brass MS 58, chrome-plated
with adjustable packing box
Handle: steel plate, galvanized with red plastic coating
resp. butterfl y handle, Alu-diecasting (Art.-No. 1454)
Temperature: up to 180°C
Pressure: up to 30 bar
Technisches Datenblatt Art.-Nr. 1452/1454
Kugelhahn UNIVERS aus Messing MS 58
Technical data sheet Art.-No. 1452/1454
Ball valve UNIVERS, brass MS 58
In den Dimensionen 3/8“ bis 1 1/4“
auch mit Flügelgriff lieferbar (Art.-Nr. 1454)
Dimensions 3/8“ up to 1 1/4“
also available with butterfl y handle (Art.-No. 1454)
Technische Änderungen und Irrtümer vorbehalten. Technical changes and errors reserved.
8080
Besuchen Sie unsere WebsiteAlle Informationen rund um unser Sortiment mit der Möglichkeit zum Download
von Prospekten und Daten fi nden Sie auf unserer Website.
Visit our websiteAll information concerning our product range, downloading of brochures and all
data you fi nd on our website.
www.hse-armaturen.de
Technische Änderungen und Irrtümer vorbehalten Technical changes and errors reserved