HAWLE-E3Gate valve

NEW

2 | HAWLE

O-ring carrier with double bayonet

Duplex stainless steel spindle

Extended edge protection

Wedge and wedge nut fully vulcanized. Form fit wedge – wedge nut connection with elastomer embedding > flexible, vibration damping and free from backlash

100% corrosion protection

Stainless steel allen screws

Extended edge protection

Bonnet

Spindle bearing

O-ring carrierwith double bayonet

Wedge nut

Duplex stainless steel spindle

Wiper ring

O-rings

Sliding discs

Bonnet gasket made of elastomer enlaces stainless steel screws

Wedge guide ensures least wear and lowest torque actuation

Body

Full straight bore

Wedge with vulcanized

elastomer all-over

HAWLE-E3 Cutting-edge gate valve technology

E3 bonnets are entirely compatible with all E2 bodies and accessories

Full straight bore - suitable for pigging

Spindle O-rings replaceable under operating pressure

All components made in Austria, incl. ductile cast iron parts

ADVANTAGES HAWLE-E3 GATE VALVE

The Hawle-E3 gate valve is the consequent advancement of the successful E2 gate valve. The O-ring carrier is connected to the allover epoxy powder-coated bonnet by a double bayonet. Load optimized POM wedge guides ensure least wear and lowest torque actuation. The form-fit wedge to wedge nut linkage with elastomer embedding is flexible, vibration damping and free from backlash. The use of Duplex stainless steel spindles in conjunction with 30 years of experience with the epoxy powder-coating process results in maximum corrosion resistance and durability without compromising the Hawle typical low torque actuation.

HAWLE-QUALITY WARRANTYMedium: Water, seawater, gas

In accordance to EN 1074-1 and -2

All illustrations, technical data, dimensions (in mm) and weights (all weights specified in kg) are non-binding. Subject to change.

HAWLE | 3

E3 valve types DN MOP (PN)

Flanged ends*EN 558-1 GR 14 EN 558-1 GR 15

50 - 200 *(250 - 600)

10, 16, 25

Reduction valve flanged ends

100 - 200 *(- 300)65 - 200 *(- 250)

10, 16

Spigot ends Spigot ends with loose flanges

50 - 200 *(- 400) 10, 16

System 2000 System 2000 / System 2000Flanged end / System 2000

50 - 200 *(- 300) 10, 16

PE-welding endsFlange / PE-welding end

50 - 200 10, 16

Socket systemsVRS Socket endBAIO Socket / BAIO SocketBAIO Socket / BAIO spigot end

80 - 200 *(- 300) 10, 16

Combi T Flanged endsSystem 2000System BAIO sockets

65 - 20050 - 15080 - 200

10, 16

Combi III Flanged endsSystem BAIO sockets

80 - 200 100- 200

10, 16

Combi IV Flanged ends

80 - 200 10, 16

VERSIONS AND DIMENSIONS

*in preparation

All illustrations, technical data, dimensions (in mm) and weights (all weights specified in kg) are non-binding. Subject to change.

Prin

ted

on re

cycl

ed, c

hlor

ine-

free

blea

ched

pap

er a

nd a

ging

..

Art

.-N

r.: Z

A3N

00E

302

E

ditio

n 05

.201

8

Your distributor:

E. Hawle Armaturenwerke GmbHWagrainer Straße 13 A-4840 Vöcklabruck

Tel.: +43 (0) 7672 72576 0 Fax: +43 (0) 7672 78464

E-Mail: hawle@hawle.atwww.hawle.at

Hand-wheel

No. 7800

Extension spindlesNo. 9000E2, No. 9500E2

Surface boxesNo. 1750, No. 2050

No. 2051K

Base plateNo. 3481K

Actuator No. 9920

Position indicator

No. 2170E2

Limit switch No. 2190E2

E2 Adapter No. 8630E2

Operating capNo. 2156, No. 2157

No. 2158

HAWAK-Pillar No. 9894, No. 9895

Additional extension spindleNo. 7820, No. 7825

Nut and BoltNo. 8810, No. 8830

No. 8840

Flat gasketNo. 3390, No. 3470

HAWLE ACCESSORIES FOR GATE VALVES

INDUFLOW Agerhatten 16 A 8DK-5220 Odense, Denmark Tel: (+45) 63 10 00 36 • Fax: (+45) 63 10 00 37 E-post: john.ronhave@induflow.dkwww.induflow.dk