-
GRUNDFOS DATA BOOKLET
NBE80-160/147-127 AS-F2-A-BQQE Grundfos Pump 99106396
Thank you for your interest in our productsPlease contact us for
more information, or visit our
websitehttps://www.lenntech.com/grundfos/NBE00/99106396/NBE-80-160-147-127-AS-F2-A-E-BQQE.html
[email protected]. +31-15-261.09.00fax. +31-15-261.62.89
BE > THINK > INNOVATE
-
Printed from Grundfos Product Centre [2018.02.043]
Position Qty. Description1 NBE 80-160/147-127 AS-F2-A-E-BQQE
Note! Product picture may differ from actual product
Product No.: 99106396
Non-self-priming, single-stage, centrifugal volute pump designed
according to ISO 5199 withdimensions and rated performance
according to EN 733 (10 bar). Flanges are PN 16 with
dimensionsaccording to EN 1092-2. The pump has an axial suction
port, radial discharge port, horizontal shaft anda back pull-out
design enabling removal of the motor, motor stool, cover and
impeller without disturbingthe pump housing or pipework.
The unbalanced rubber bellows seal is according to DIN EN
12756.The pump is close-coupled to a fan-cooled, permanent-magnet
synchronous motor.The motor includes a frequency converter and PI
controller in the motor terminal box. This enablescontinuously
variable control of the motor speed, which again enables adaptation
of the performance toa given requirement.
Further product detailsThe product's minimum efficiency index
(MEI) is greater or equal to 0.70. This is by the
CommissionRegulation (EU) considered as an indicative benchmark for
best-performing water pump available onthe market as from 1 January
2013.
An external sensor can be connected if controlled pump operation
is required for flow, differentialpressure or temperature control.A
control panel on the motor terminal box enables setting of required
setpoint as well as setting ofpump to "Min." or "Max." operation or
to "Stop". The Grundfos Eye indicator on the control panelprovides
visual indication of pump status:
- "Power on": Motor is running (rotating green indicator lights)
or not running (permanently greenindicator lights)
- "Warning": Motor is still running (rotating yellow indicator
lights) or has stopped (permanentlyyellow indicator lights)
- "Alarm": Motor has stopped (flashing red indicator
lights).
Communication with the pump is possible by means of the Grundfos
GO Remote (accessory). Theremote control enables further settings
as well as reading out of a number of parameters such as"Actual
value", "Speed", "Power input" and total "Power consumption".
The back pull-out design means that the pump can be serviced by
a single person without disturbingthe pump housing or pipe
work.
The pump is to be secured to the foundation with bolts through
the motor feet. The pump is deliveredwith steel support blocks to
be fitted under the motor feet during installation, thus ensuring a
minimumclearence of 5 mm between the motor stool/motor flange and
the foundation.
http://product-selection.grundfos.com/product-detail.html?productnumber=99106396&freq=50&lang=ENU
-
Printed from Grundfos Product Centre [2018.02.043]
Cast-iron parts have an epoxy-based coating made in a cathodic
electro-deposition (CED) process. CED is ahigh-quality dip-painting
process where an electrical field around the products ensures
deposition of paint particlesas a thin, well-controlled layer on
the surface. An integral part of the process is a pretreatment. The
entire processconsists of these elements:
1) Alkaline-based cleaning.2) Zinc phosphating.3) Cathodic
electro-deposition.4) Curing to a dry film thickness 18-22 my m.The
colour code for the finished product is NCS 9000/RAL 9005.
PumpThe pump housing has both a priming and a drain hole closed
by plugs.The impeller is a closed impeller with double-curved
blades with smooth surfaces. The impeller isstatically balanced
according to ISO 1940-1 class G6.3 and hydraulically balanced to
compensate foraxial thrust.Wear rings used in pump housing and for
impeller are made of bronze/brass or cast iron.
Motor stool and pump cover are made of cast iron (EN-GJL-250).
Coupling guards are fitted to themotor stool. The pump cover is
provided with a manual air vent screw for venting of the pump
housingand the shaft seal chamber.
The pump is fitted with an unbalanced rubber bellows seal with
torque transmission across the springand around the bellows. Due to
the bellows, the seal does not wear the shaft, and the axial
movementis not prevented by deposits on the shaft.Primary seal:
- Rotating seal ring material: Silicon carbide (SiC)- Stationary
seat material: Silicon carbide (SiC)
This material pairing is used where higher corrosion resistance
is required. The high hardness of thismaterial pairing offers good
resistance against abrasive particles.Secondary seal material: EPDM
(ethylene-propylene rubber)EPDM has excellent resistance to hot
water. EPDM is not suitable for mineral oils.
MotorThe motor is a totally enclosed, fan-cooled motor with
principal dimensions to IEC and DIN standards.Electrical tolerances
comply with IEC 60034.
The motor efficiency is classified as IE5 in accordance with IEC
60034-30-2.The motor requires no external motor protection. The
motor control unit incorporates protection againstslow- and
quick-rising temperatures, e.g. constant overload and stalled
conditions.
The terminal box holds terminals for these connections:- one
dedicated digital input- two analog inputs, 0(4)-20 mA, 0-5 V, 0-10
V, 0.5 - 3.5 V- 5 V voltage supply to potentiometer and sensor- one
configurable digital input or open-collector output- Grundfos
Digital Sensor input and output- 24 V voltage supply for sensors-
two signal relay outputs (potential-free contacts)- GENIbus
connection- interface for Grundfos CIM fieldbus module.
Technical data
Liquid:Pumped liquid: WaterLiquid temperature range: -25 .. 120
°CLiquid temperature during operation: 20 °CDensity: 998.2
kg/m³
Technical:Speed for pump data: 3000 rpmRated flow: 167 m³/hRated
head: 17.8 mActual impeller diameter: 147-127 mmImpeller nom: 160
mm
-
Printed from Grundfos Product Centre [2018.02.043]
Position Qty. DescriptionPrimary shaft seal: BQQESecondary shaft
seal: NONECurve tolerance: ISO9906:2012 3B
Materials:Pump housing: Cast iron
EN-GJL-250ASTM A48-40 B
Impeller: Cast ironEN-GJL-200ASTM A48-30 B
Shaft: Stainless steel1.4301304
Rubber: EPDMWear ring mat.: High alloy brass(CuZn34Mn3AI2
Installation:Maximum ambient temperature: 50 °CMaximum operating
pressure: 16 barFlange standard: EN 1092-2Pump inlet: DN 100Pump
outlet: DN 80Pressure rating: PN 16
Electrical data:Motor type: 160MHIE Efficiency class: IE5Rated
power - P2: 11 kWMains frequency: 50 HzRated voltage: 3 x 380-500
VRated current: 20,3-16,0 ACos phi - power factor: 0,93-0,90Rated
speed: 360-4000 rpmEfficiency: 93,1%Number of poles: 2Enclosure
class (IEC 34-5): IP55Insulation class (IEC 85): FLubricant type:
Grease
Others:Minimum efficiency index, MEI ≥: 0.70ErP status: EuP
Standalone/Prod.Net weight: 127 kgGross weight: 148 kgShipping
volume: 0.509 m³
-
Printed from Grundfos Product Centre [2018.02.043]
99106396 NBE 80-160/147-127 50 HzH
[m]
0
5
10
15
20
25
30
Q [m³/h]0 20 40 60 80 100 120 140 160 180 200
eta[%]
0
20
40
60
80
100
NBE 80-160/147-127, 3*500 V
110 %
100 %
90 %
80 %
70 %
60 %
50 %
40 %
25 %20 %
P[kW]
0
2
4
6
8
10
12
NPSH[m]
0
10
20
30
40
50
60P1 (motor+freq.converter)
P2
-
Printed from Grundfos Product Centre [2018.02.043]
H[m]
0
5
10
15
20
25
30
Q [m³/h]0 50 100 150
eta[%]
0
20
40
60
80
100
NBE 80-160/147-127, 3*500 V
110 %
100 %
90 %
80 %
70 %
60 %
50 %
40 %
25 %20 %
P[kW]
0
2
4
6
8
10
NPSH[m]
0
10
20
30
40
50
P1 (motor+freq.converter)
P210
0
125
36880
225
210
254
108
160
139
173
173
317
237
406 140
350
14.5
185
182
8 x 19
1XM32+5XM208 x 19
3
15
8
26
23
25
24
7
21
20
22
B
Y
6
5
2
4
10
A
+24 V*
1
149
12
17
19
11
18+24 V*
OC DI
+24 V*
AI2
GDS RX
GDS TX
GND
GENIbus A
GENIbus B
+24 V
GND
GENIbus Y
GND
DI1
AI1
DI3/OC1
LiqTec
AI3
GND
DI2
LiqTec
GND
AO
Pt100/1000
Pt100/1000
DI4/OC2
GND
+24 V*OC DIGND
NC
C2
NO
NC
C1
NO
+24 V*+24 V* +24 V*/5 V*
L2
L1
L3
PE
L3
L2
L1
+24 V* +24 V*/5 V*+24 V*
+24 V*/5 V*
+5 V*
+5 V
+24 V
+5 V
+5 V*
Description ValueGeneral information:
Product name: NBE 80-160/147-127AS-F2-A-E-BQQE
Product No: 99106396EAN number: 5712606871742Technical:Speed for
pump data: 3000 rpmRated flow: 167 m³/hRated head: 17.8 mActual
impeller diameter: 147-127 mmImpeller nom: 160 mmPrimary shaft
seal: BQQESecondary shaft seal: NONEShaft diameter: 24 mmCurve
tolerance: ISO9906:2012 3BPump version: ASMaterials:Pump housing:
Cast iron
EN-GJL-250ASTM A48-40 B
Impeller: Cast ironEN-GJL-200ASTM A48-30 B
Shaft: Stainless steel1.4301304
Material code: ARubber: EPDMCode for rubber: E
Wear ring mat.: High alloybrass(CuZn34Mn3AI2
Installation:Maximum ambient temperature: 50 °CMaximum operating
pressure: 16 barFlange standard: EN 1092-2Connect code: F2Pump
inlet: DN 100Pump outlet: DN 80Pressure rating: PN 16Wear ring(s):
neckring(s)Liquid:Pumped liquid: WaterLiquid temperature range: -25
.. 120 °CLiquid temperature during operation: 20 °CDensity: 998.2
kg/m³Electrical data:Motor type: 160MHIE Efficiency class: IE5Rated
power - P2: 11 kWMains frequency: 50 HzRated voltage: 3 x 380-500
VRated current: 20,3-16,0 ACos phi - power factor: 0,93-0,90Rated
speed: 360-4000 rpmEfficiency: 93,1%Number of poles: 2Enclosure
class (IEC 34-5): IP55Insulation class (IEC 85): FMotor protec:
YESMotor No: 99306732Mount. design. acc. IEC 34-7: IM B35Lubricant
type: GreaseControls:Control panel: HMI300 - Advanced
12536880
210
108
139
317
406140
14.5
182
8 x 19
1XM32+5XM208 x 19
http://product-selection.grundfos.com/product-detail.html?productnumber=99106396&freq=50&lang=ENU
-
Printed from Grundfos Product Centre [2018.02.043]
Description ValueFunction Module: 300Others:Minimum efficiency
index, MEI ≥: 0.70ErP status: EuP Standalone/Prod.Net weight: 127
kgGross weight: 148 kgShipping volume: 0.509 m³Config. file no:
99100723
-
Printed from Grundfos Product Centre [2018.02.043]
99106396 NBE 80-160/147-127 50 Hzcos phi
eta
0.0
0.2
0.4
0.6
0.8
P2 [kW]0 1 2 3 4 5 6 7 8 9 10
I[A]
0
4
8
12
16
NBE80-160/147-127 + 160MH 11 kW 3*500 V, 50 Hz
eta
cos phi
I
n[rpm]
0
1000
2000
3000
P1[kW]
0
4
8
n
P1 (motor+freq.converter)
n = 109 %
-
Printed from Grundfos Product Centre [2018.02.043]
99106396 NBE 80-160/147-127 50 Hz
Note! All units are in [mm] unless others are stated.Disclaimer:
This simplified dimensional drawing does not show all details.
100
125
368
80
225
210
254
108
160
139
173 173
317
237
406
140
350
14.5
185
182
8 x
19
1XM
32+5
XM20
8 x
19
-
Printed from Grundfos Product Centre [2018.02.043]
99106396 NBE 80-160/147-127 50 Hz
Note! All units are in [mm] unless others are stated.
3
15
8
26
23
25
24
7
21
20
22
B
Y
6
5
2
4
10
A
+24 V*
1
14
9
12
17
19
11
18+24 V*
OC DI
+24 V*
AI2
GDS RX
GDS TX
GND
GENIbus A
GENIbus B
+24 V
GND
GENIbus Y
GND
DI1
AI1
DI3/OC1
LiqTec
AI3
GND
DI2
LiqTec
GND
AO
Pt100/1000
Pt100/1000
DI4/OC2
GND
+24 V*OC DIGND
NC
C2
NO
NC
C1
NO
+24 V*+24 V* +24 V*/5 V*
L2
L1
L3
PE
L3
L2
L1
+24 V* +24 V*/5 V*+24 V*
+24 V*/5 V*
+5 V*
+5 V
+24 V
+5 V
+5 V*
-
Disclaimer: The information about the Grundfos pump in this
document may be outdated.Data may be subject to alterations without
further notice.Please contact us to verify the data above is still
accurate/up-to-date.
All information is copyright Grundfos.
[email protected]. +31-15-261.09.00fax.
+31-15-261.62.89
