GRAFIK Eye QS Wireless Control Unit SPEC (369313) mm orol 369313f 1 05.26.17 ® Job Name: Job Number: Model Numbers: SPECIFICATION SUMITTAL Page Wireless Control Unit GRAFIK Eye QS

Preset Dimming Controls

369313f 1 05.26.17

®

Job Name:

Job Number:

Model Numbers:

PageSPECIFICATION SUBMITTAL

Wireless Control Unit

GRAFIK Eye QS Wireless Control UnitGRAFIK Eye QS Wireless is the premier energy-saving light and shade control. The GRAFIK Eye QS control unit includes an astronomic timeclock, intuitive lighting presets, and direct shade control. Now with wireless technology, you can use the GRAFIK Eye QS Wireless control unit to seamlessly integrate with a variety of Lutron wireless products and systems, including RadioRA 2, Radio Powr Savr occupancy, vacancy, and daylight sensors, Sivoia QS Wireless shades, Pico wireless controls, and other GRAFIK Eye QS Wireless control units. Additionally, the GRAFIK Eye QS Wireless is compatible with all Lutron wired QS products and systems, including Quantum.

Mechanical Dimensions

Fits into a 4-gang U.S. backbox, 31⁄2 in (90.4 mm) deep (Lutron P/N 245254) or 3 in (76.2 mm) deep (Lutron P/N 241400)

Front View Side View

93⁄8 in (239 mm)

2 in (51 mm)

3/8 in (10 mm)

411⁄16 in (119 mm)

LUTRON

1

2

3

4

Off

Preset

Close

Open


369313f 2 05.26.17

®

Job Name:

Job Number:

Model Numbers:



System TopologiesThe GRAFIK Eye QS Wireless control unit can be specified in four different system topologies. Examples of each are shown below.

30 ft (10 m) wireless range; 60 ft (20 m) in open air

Example of Wired System

LUTRONLUTRON

LUTRON LUTRON

LUTRON

LUTRON LUTRON

LUTRON

LUTRON

LUTRON

LUTRONLUTRON

LUTRON LUTRON

LUTRON

LUTRON LUTRON

LUTRON

LUTRON

LUTRON

QSE-CI-NWK-E

Sivoia QS shade

seeTouch QS wallstation

seeTouch QS wallstation

Wired occupancy sensor

GRAFIK Eye QS wireless control unit


Wired QS link

Quantum® processor

QS sensor module

Energi Savr Node unit

Example of GRAFIK Eye-centric Wireless System

LUTRONLUTRON

LUTRON LUTRON

LUTRON

LUTRON LUTRON

LUTRON

LUTRON

LUTRON

LUTRONLUTRON

LUTRON LUTRON

LUTRON

LUTRON LUTRON

LUTRON

LUTRON

LUTRON

Wireless Sivoia QS

shadeWireless occupancy sensor



Pico wireless control

Wireless daylight sensor

Example of Mixed GRAFIK Eye-centric Wired/Wireless System

LUTRONLUTRON

LUTRON LUTRON

LUTRON

LUTRON LUTRON

LUTRON

LUTRON

LUTRON

LUTRONLUTRON

LUTRON LUTRON

LUTRON

LUTRON LUTRON

LUTRON

LUTRON

LUTRON

Wireless Sivoia QS

shade

Wired QS link

Wired occupancy

sensor

seeTouch QS walstations Wireless

occupancy sensor


Pico wireless control

Wireless daylight sensor

Refer to RadioRA 2 documentation (www.lutron.com/radiora2) for specification information.

Note: Wired QS link is disabled when the GRAFIK Eye QS control unit is added to a RadioRA 2 system.

Example of Wireless System with Main Repeater (RadioRA 2)

LUTRONLUTRON

LUTRON LUTRON

LUTRON

LUTRON LUTRON

LUTRON

LUTRON

LUTRON

LUTRONLUTRON

LUTRON LUTRON

LUTRON

LUTRON LUTRON

LUTRON

LUTRON

LUTRON

Wireless occupancy

sensor

Main repeater

RadioRA 2 dimmer

RadioRA 2 keypad



369313f 3 05.26.17

®

Job Name:

Job Number:

Model Numbers:



Features•LutronproprietaryClearConnectRFtechnology.

Operates in the 434 MHz band.

•Pushbuttonrecalloffourpresetlightingscenes,plus Off.

•Sixteen(16)totalavailablescenes,plusOffscene.

•Zonescancontrolmanylightsourcetypesdirectlyor through power modules.

•Optionalintegratedshadecontrolbuttons,whichcan also be added to the unit after installation.

•Masteroverridebuttonstoraiseandloweralllights.

•Allowssetupoflightingscenesandshadepresetsusing buttons on the control unit.

•Built-ininfrared(IR)receiver.

•ExternalIRconnection.

•Built-inastronomictimeclock.

• Infoscreenshowszonelightlevelpercentage,energy savings, zone labeling, and programming.

•Lockoutoptionpreventsaccidentalchanges.

•Occupancysensorinputand24V- power for one occupancy sensor.

•QScommunicationlinkforseamlessintegrationoflights, motorized window treatments, occupancy sensors, wallstations, and integration interfaces.

•CompatiblewithallLutronQSsystemcomponents.

•Wirelesscommunicationforseamlessintegrationwith a variety of Lutron wireless products and systems, including RadioRA 2, Radio Powr Savr occupancy, vacancy, and daylight sensors, Sivoia QS wireless shades, Pico wireless controls, and other GRAFIK Eye QS wireless control units.

•Backlitbuttonswithengravingmakeuniteasytolocate and operate.

•Availableinavarietyofcolorsandfinishes.

LUTRON

OK

1 2 3 4 5 6

MiniBMicro

Zonecontrol

Optional shade control keypad

Info screen

Infrared receiver

Lighting control keypad

1

2

3

4

Off

Off

Preset

Close

1

2

3

4

Open

Preset

Close

Open

Note: General Engraving (-EGN) shown.

orUSBreceptacle(oneonly):


369313f 4 05.26.17

®

Job Name:

Job Number:

Model Numbers:



Zonescanalsocontrolthefollowinglightingsourceswithasmooth, continuous square law dimming curve or on a full conduction non-dim basis through separate Lutron power modules:

•Electroniclow-voltagetransformers(useELVorPhase-Adaptive power module)

•Lutron3-wirecontrolledelectronicfluorescentdimmingballasts (use fluorescent 3-wire power module)

•Lutron3-wirecontrolledLEDdrivers•Non-dim(useswitchingmodule)•0–10V- (use ten-volt interface)

Note: A zone may be programmed to control only one load type at a time.

Key Design Features•RFmeetsFCCPart15ClassB.•LightningstrikeprotectionmeetsANSI/IEEEstandard

62.41-1980. Can withstand voltage surges of up to 6000 V~ and current surges of up to 3000 A.

•Testedtowithstand16kVelectrostaticdischargewithoutdamage or memory loss.

•RTISS Equipped: Compensates in real time for incoming linevoltagevariations(novisibleflickerwith+/–2%changeinRMSvoltagepercycle,and+/–2%Hzchangeinfrequency per second).

•Powerfailurememoryretainsprogrammingandlightlevelsettings for up to 10 years in the event of a power loss.

•TheGRAFIKEyeQScontrolunitsupplies3PowerDrawUnits(PDUs)ontheQSlink. Forcompleteinformation,see“PowerDrawUnitsontheQS Link,” Lutron P/N 369405.

•Faceplateishingedatthetopandbottom,andstaysopenat 180° for ease of access.

Scene and Shade Buttons•Large,roundedbuttonsareeasytouse.•Backlitbuttonswithoptionalengravingmakeiteasyto

find and to operate the control unit in low light conditions (backlight can be disabled).

•Optionalbuttonengravingisangleduptotheeyeforeasyreading.

•Predefinedlabelstickersareincludedforfieldlabeling.•4presetlightingscenes,plusOff,areaccessiblefromthe

front of the control unit.•12additionalscenesarestoredinthecontrolunitand

are accessible from the integral timeclock, seeTouch QS wallstations, and QS interfaces.

•Lightlevelsfadesmoothlybetweenscenes.Fadetimecan be set differently for each scene: 0 to 59 seconds, or 1 to 60 minutes. Maximum fade time from Scene Off is 3 seconds.

Input Power•120–127V~ 50/60 Hz•220–240V~ 50/60 Hz

Listings (120 – 127 V~)•ULR Listed•CSA•NOM•CEC(Title24)•FCCPart15ClassB• ICRSS-210•SCT

Environment•32to104°F(0to40°C)•Relativehumiditylessthan90%non-condensing

Lighting Sources/Load Types•ZonesonEnergiSavrNodeproductswiredtothesame

QS link –ZonesonEnergiSavrNodewithSoftswitch –ZonesonEnergiSavrNodefor0–10V- –ZonesonEnergiSavrNodewithEcoSystemPleasereferto“RemoteZoneMapping”forimportantinformation.

•DMXchannel(s)throughDMXoutputinterface (QSE-CI-DMX).Pleasereferto“AccessoryControls:DMXOutput Interface”

Zonescanalsocontrolthefollowinglightingsourceswithasmooth, continuous square law dimming curve or on a full conduction non-dim basis:

•Cree LR4/6, 120 V~ fixtures (for loading capacities, please refertotheLEDreportcardlocatedat www.lutron.com/LEDtool)

•DimmableLEDBulbs(foracompletelistofapproveddimmableLEDspleasecall1.800.523.9466orvisit www.lutron.com/dimcflled)

• Incandescent•Halogen•Magneticlow-voltagetransformer•LutronTu-Wireelectronicfluorescentdimmingballast•AdvanceMarkX® electronic dimming ballast•Neonandcoldcathode•Non-dim(incandescent,magneticlow-voltage,Tu-Wire,or

neon/cold cathode) Please refer to “Capacities” for more information.

Specifications


369313f 5 05.26.17

®

Job Name:

Job Number:

Model Numbers:



Astronomic Timeclock• Integraltoallunits.•7dailyschedulesavailable.•Oneavailableholidayscheduleisprogrammablebydate

up to one year in advance.•25eventsperdaymaximum.•Timeclockeventsareprogrammabletocontrolscenesthat

affect any Energi Savr Node unit connected on the QS link without changing the local scene on the GRAFIK Eye QS control unit .

•Astronomictimesareprogrammablebyintegralcity database or by entering latitude and longitude. Sunrise/Sunset times automatically adjust throughout the year based on location.

•AutomaticallyadjustsforDaylightSavingTime(DST); DSTisprogrammable.

•Localtimeclockeventscanactivateanyofthefollowingfeatures:

–Scenes1to16andOff –Anyavailableshadepresets –StartandEndafterhoursmode –EnableandDisabledaylightingforallzones/groups –EnableandDisableoccupancyforoccupancy/vacancy

sensors –EnableandDisableoccupiedeventsforalloccupancy

sensors

System Communications and Capacities•Low-voltagetypeIECPELV/NEC® Class 2 wiring connects

control units, wallstations, motorized shades, and control interfaces.

•AQSsystemcanhaveupto100devicesand100zones.•AQSsystemcanhaveupto30wirelessdevices.

Infrared• Infrared(IR)receiverallowsinfraredtransmitterstoselect

8 scenes, raise/lower lighting zones, or raise/lower shades.•Transmitterbuttonsimitatebuttonsonfaceplate.•50ft(15m)lineofsightrange.•Terminalblockinfraredinputforconnectiontoawired

IR input from third-party equipment.• IRcanbedisabledviaprogramming.•WorkswithLutronGRX-ITandGRX-8ITinfraredremote

controls.

Shade Control•TheGRAFIKEyeQScontrolunitcanincludeupto3 shade

button columns. Each column has backlit open, preset, close, and raise/lower buttons.

•Eachshadebuttoncolumncanbeprogrammedtooperateone shade or a group of shades. (Shades may be assigned to more than one shade button column).

•Faceplatesareavailablewith1,2,and3shadebuttoncolumns.

Wireless shade limitations:•AccesstotheSivoiaQSWirelesselectronicdriveunit(EDU)

is required to associate shades with the GRAFIK Eye QS control unit and set their raise/lower limits.Exception: Sivoia QS Wireless cellular shades allow limit setting from the GRAFIK Eye QS wireless control unit.

•Wiredandwirelessshadesmaynotbeprogrammedintothe same shade button column; however, both may be used on the same GRAFIK Eye QS control unit.

•Scenecommandsthataffectwirelessshadesacrossmultiple shade button columns will have a 1-second delay from column to column. This does not occur in RadioRA 2 systems.

Zone Control•Eachzonehasadedicatedraiseandlowerbuttonto

adjust the zone.•Eachzonehasadedicated7-LEDbargraphforlevel

status. Percentage of light level and energy saved is displayed on the info screen.

•AllzoneinformationhasbluebacklitLEDs.Backlightturnsoff when idle for 30 seconds.

•High-endandlow-endtrimsettingsareadjustableperzone(highendfrom99to55%;lowendfrom45to1%). Note: Trim for remote zones must be adjusted locally on the Energi Savr Node unit.

•Eachzoneisprogrammabletoonlyoneloadtypeatatime.

Info Screen•OLED(organicLED)screenisviewablefromallangles.•Screenturnsoffwhenidlefor30seconds.•Programmablezonelabels.•Programmablescenelabels.•Statusofreal-timezonepercentageandenergysavings.•Programmabletimeclockschedules.•Programmableshadelabels.•Selectabledisplaylanguages: –English –Spanish –French –Italian –German –Portuguese

Specifications (continued)


369313f 6 05.26.17

®

Job Name:

Job Number:

Model Numbers:



Accessory Controls: seeTouch QS Wallstations (QSWS2)

•WiredseeTouchQSwallstationsprovidethefollowingfeatures:

–Accesstooneormoreofthe16scenesontheGRAFIK Eye QS Wireless control unit

–Zonetoggle,partitioning,sequencing,finetune,panicmode, and timeclock enable/disable

–Contactclosureinputs –Certainfunctionsareonlyavailableonspecificwallstation

configurations. Refer to the seeTouch QS specification submittal.

Wireless RF Compatibility•FeaturesLutronproprietaryClearConnectRFTechnology•Operatesinthe434MHzband•CompatiblewithotherLutronwirelessproducts/systems,

such as: –Picowirelesscontrol(P/NQSR4PorMRF2) –RadioPowrSavroccupancy/vacancy/daylightsensors

(P/N LRF2-) –RadioRA2wirelesssystem –SivoiaQSwirelessproducts –OtherGRAFIKEyeQSwirelesscontrolunits

(P/N QSGRJ-)

Accessory Controls: Pico Wireless Control (PJ models)

•ThePicoWirelessControlisbatterypowered.ItcancontrolGRAFIK Eye QS wireless control units within a 30 ft (10 m) range (60 ft [20 m] in open air). It provides the following features:

–ControlofoneormorezonesontheGRAFIKEyeQSWireless control unit: turns zone(s) on or off, raises/lowers zone(s), allows programmable light levels for each button, and goes to user-programmable preset level

–ControlofoneormorescenesontheGRAFIKEyeQS Wireless control unit: the Pico wireless control can access any three sequential scenes (1 through 16), or any two sequential scenes and Off; and can raise and lower lighting levels.

Note: “Unaffected” is not a valid level for Pico zone programming.

Accessory Controls: QS Sensor Module (QSM2)•TheQSSensorModuleprovidesameanstolinkwired

or wireless occupancy sensors or daylight sensors, Pico controls, and wired infrared sensors to a GRAFIK Eye QS control unit via the wired QS link.

–Occupancysensorswired(orwirelesslylinked)toa QS Sensor Module can be used by one or more GRAFIK Eye QS control units on the wired link.

–Daylightsensorswired(orwirelesslylinked)toa QS Sensor Module can be used by one or more GRAFIK Eye QS control units on the wired link.

–Picowirelesscontrolscancontroleitheroneormorezones or scenes on the GRAFIK Eye QS control unit.

–Picowiredcontrolscanbeused,whenconnectedtoa QS Sensor Module, to control one or more zones or scenes on the GRAFIK Eye QS control unit.

–Infraredsensorscancontroleitheroneormorezonesorscenes on the GRAFIK Eye QS control unit. Functionality varies; refer to the documentation for the QS Sensor Module for details.

Accessory Controls: Contact Closure Input/Output Interface (QSE-IO)

•Recallspresetlightlevelsforthefollowingsetofscenesonthe GRAFIK Eye QS control unit: –Scenes1–4andOff –Scenes9–12andOff –Scenes5–8andOff –Scenes13–16andOff

•Sequencescenes5–16,Enable/DisableZoneLockout,Enable/DisableSceneLockout,Enable/DisablePanicMode,Enable/DisableTimeclock.

•OccupancySensors.Anindividualinputcountsas1 occupancy sensor for the GRAFIK Eye QS control unit. Each input can be assigned to either Scene Control or ZoneControl(pleaserefertotheOccupancySensor(s)section of this guide).

• ZoneToggle.Allowsaninputtotoggleoneormorezonesbetween programmable preset level(s) and off.

•ShadeOutputmode.AShadeColumnontheGRAFIKEyeQScontrolunitcanbelinkedtocontroloutputs1–3and/oroutputs4–5ontheQSE-IO.

Accessory Controls: DMX Output Interface (QSE-CI-DMX)

•AnyzoneontheGRAFIKEyeQScontrolunitcanbemappedtoanysingleDMX512Channel.

•AnyzoneontheGRAFIKEyeQScontrolunitcanbesimultaneouslymappedtoanythreeDMX512channels(providingRGB/CMYcontrol).

•DMXloadscannotbeusedwithdaylighting.



369313f 7 05.26.17

®

Job Name:

Job Number:

Model Numbers:



Accessory Controls: Ethernet and RS232 Interface (QSE-CI-NWK-E)

•Allowsformonitoringandcontroloftheoutputsandlocalscenes of the GRAFIK Eye QS control unit.

Accessory Controls: QS Keyswitch Wallstations (QSWS2-KS)

•RecallspresetlightlevelsforanytwoscenesincludingOff•Allowsfine-tuning(raise/lowerlevel)ofazoneorgroupof

zones•Starts/Stopsscenesequencing(Scenes1–4or Scenes5–16)

•Enables/DisablesTimeclock•Enables/Disablesoccupancysensors•Enables/Disableddaylightsensors•AllowstoggleofZone(s)toapresetlevelandoff•Enables/Disablespanicmode•Starts/Stopsafterhoursmode

Other Accessory Controls and Devices•EnergiSavrNodeQS(ESN).SeetheSpecification

Submittal for complete details.

Occupancy Sensor(s)•TheGRAFIKEyeQScontrolunitworkswithoccupancy

sensors through either: –Scene Control: Up to 16 sensors activate user-selected

occupancy and vacancy scenes.* –ZoneControl:Uptofoursensorsperzoneactivate

user-selected occupancy and vacancy zone levels. •Occupancysensorsmayinclude: –ContactclosuresensorswiredtoCCIinputonbackof

the GRAFIK Eye QS control unit –WirelessRadioPowrSavroccupancyorvacancysensors

(model numbers starting with LRF2) –WiredorwirelesssensorsconnectedQSSensorModule

(QSM)• Ifanysensorinagroupdetectsoccupancy,thenthe

GRAFIK Eye QS control unit will go to the designated occupancy scene or zone level.

• Ifallsensorsinagroupdetectvacancy,thentheGRAFIK Eye QS control unit will go to the designated vacancy scene or zone level.

•Lowbattery:theDiagnosticsscreenwilldisplayalowbattery symbol when applicable.

• IftheGRAFIKEyeQScontrolunitdoesnotreceiveasignalfrom an occupancy sensor on the link (usually due to a dead battery), the lights associated with that sensor will go to the occupied level.

Daylight Sensor(s)•TheGRAFIK Eye QS control unit allows daylight sensors to

control one or more lighting zones to adjust electric light levels based on measured daylight levels.

•Daylightsensorsmayinclude: –Wireless Radio Powr Savr (model numbers starting with

LRF2) –Wired or wireless sensors connected to a QS sensor

module (QSM)•AdaylightsensorcancontroloneormoreGRAFIK Eye QS

zones: –Each zone can be calibrated to target light levels –A zone can be controlled by no more than one daylight

sensor•Daylightcontrolcanbeenabledordisabledona

scene-by-scene basis –Bydefault,daylightcontrolisenabledinallscenes

Note:DaylightcontrolthroughtheGRAFIKEyeQScontrolunit only affects select lighting loads. Shade groups cannot becontrolledbydaylightsensors.DaylightingdoesnotaffectDMXorRGB/CMYDMXloads.

DaylightingofRemoteZoneslinkedtoEnergiSavrNodezones must be configured at the Energi Savr Node unit or through the Energi Savr Node app for iPod.


iPod is a trademark of Apple Inc. registered in the U.S. and other countries.

* Applicable only to units that ship with firmware version 9.002 and higher. Previous versions support up to 4 sensors.


369313f 8 05.26.17

®

Job Name:

Job Number:

Model Numbers:



Contact Closure Input (CCI) with Power Supply Output•EachGRAFIK Eye QS control unit has one contact closure

input (Terminal A). –The attached device must provide a dry contact closure

or solid-state output. – Input is miswire-protected up to 36 V-.•Thecontactclosureiscapableofacceptingthefollowing

types of inputs: –Maintained(default):TheGRAFIKEyeQScontrolunitwill

act on both a contact closure and a contact open/release event.

–Momentary:TheGRAFIKEyeQScontrolunitwillactononly contact closure events.

•EachGRAFIK Eye QS control unit can supply 50 mA maximum at 24 V-.

–Useful for powering occupancy sensors. –An auxiliary power supply must be used if the device

requires more than 50 mA.•TheCCIiscapableofoperatinginthefollowingmodes –Occupancy: If an occupancy sensor is wired directly to

the GRAFIK Eye QS control unit, choose this setting so that the occupancy sensor will work correctly.

–Emergency: This setting allows the GRAFIK Eye QS to work with a LUT-ELI. When an emergency situation is detected, all lights will go to full on, and no operations will be allowed until the emergency signal is cleared.

–Afterhours: Allows the CCI to start and end the afterhours mode.

–Timeclock: Allows the CCI to enable and disable the timeclock.

–Scene Lockout: Prevents the user from making any changes to the control unit. The current scene will stay on until the CCI enables normal operation.

–Never Save: Prevents any changes from being saved while the CCI is being used.

–DisableCCI:TheCCIwillhavenoeffectonthesystemand will not appear on the list of available sensors.

Security Lockout Password•A4-digitpassword(usingcharactersAtoZand0to9)

can be enabled/disabled to lock out access to the Programming Menu.

•BydefaultthereisnopasswordenabledontheGRAFIK Eye QS control unit.

• Ifcasethe4-digitpasswordisforgotten,contactLutronCustomer Assistance to regain access.

Specifications (continued)Remote Zone Mapping

•MapaGRAFIKEyeQSzonedirectlytoanEnergiSavr Node output so that programmed scenes in the GRAFIK Eye QS control unit will directly control the output levels of the Energi Savr Node.

•Adjusthigh-endandlow-endtrimforremotezonesthroughthe Energi Savr Node or Energi Savr app software.

•ChangeloadtypesofremotezonesthroughtheEnergi Savr Node or Energi Savr app software.

•ConfiguredaylightingforremotezonesthroughtheEnergi Savr Node or Energi Savr app software.

•Required: –GRAFIKEyeQScontrolunitwithfirmwareversion

7.000 or higher –EnergiSavrNodeunitwithfirmwareversion6.000or

higher –EnergiSavrappversion6.0.0orhigher(requiredonlyif

the Energi Savr Node unit has been configured using the app)

Partitioning•Whenpartitionisopen,creatingonelargespace,

automatically combines lighting preset functions for multiple GRAFIK Eye QS control units.

•Whenpartitionisclosed,creatingtwoormoresmallerspaces, lighting preset functions become independent.

•RequiresoneQSWS2-2Bwallstation,aGRX-IRPSinfraredtransmitter/receiverpair,andaGRX-12VDCpowersupplyfor operation.

• Ifoccupancysensorsarerequiredinapartitionedspace,note that each room’s occupancy sensor(s) will operate independent of the partition status.


369313f 9 05.26.17

®

Job Name:

Job Number:

Model Numbers:



220 – 240 V~ 50 / 60 Hz 120 V~ 50 / 60 HzUnit Capacity (watts) 3000 2000MLV 3000 VA / 2400 W 2000 VA / 1600 WZone Capacity (watts) 40–1200 25–800MLV 40–1200VA/40–960W 25–800VA/25–600W

Load Type Notes•Allelectroniclow-voltage(ELV)lightingusedwithaninterfacemustberatedforreversephasecontroldimming.Before

installing an ELV light source, verify with the manufacturer that their transformer can be dimmed. When dimming, an ELV interface(suchasthePHPM-PA-DV-WH)mustbeusedwiththecontrolunit.

•Notallzonesmustbeconnected;however,connectedzonesmusthaveaminimumloadasspecifiedabove.•Maximumtotallightingloadforamagneticlow-voltage(MLV)variesbyinputvoltage: –120–127V~: 800 VA / 600 W –220–240V~: 1200 VA / 960 W•MaximumtotallightingloadforLutronTu-WireandAdvanceMarkX® electronic dimming ballasts (120 to 127 V~ only) must

not exceed 6 A per zone or 16 A per unit.•Nozonemaybeloadedwithmorethanthecapacityspecifiedabove.Forhigherwattageapplications,orfor277V~ applications,useLutronpowermodulePHPM-PA,PHPM-WBX,PHPM-PA-DV,PHPM-SW,orPHPM-WBX-DV.

•Forcontrollinglow-wattageloads(CFL,LED)inanon-dimapplication,contactLutronCustomerAssistancefortheappropriate solution.

System Limits•TheQSwiredcommunicationlinkislimitedto100devicesor100zones.

Capacities

XJO


369313f 10 05.26.17

®

Job Name:

Job Number:

Model Numbers:



GRAFIK Eye QS Wireless Control UnitStandard Model Numbers

•Seefollowingpagesfororderingcustom(non-standard)modelnumbers•SeeStandardColorCombinationspageforfaceplate,stripe,andbuttoncolors

QSGRJ– P– WH

Number ofZones

3 = 3 zones4 = 4 zones6 = 6 zones

Phase Control Triac

Prefix

Number of Shade Columns

Omit = none1 = 1 shade

column

Omit = WhiteT = Translucent

TopDoorColor

White (standard color)

Example:QSGRJ-6P-1TWH6-zone standard white unit with 1 shade column and translucent top door.

Unit will ship unengraved with engraving certificate that customer can redeem at no charge.

Important Note:For any non-standard units, you must order bothaBaseUnitandaFaceplateKit.Please see the Custom Ordering Information on the following pages.

3 ZonesQSGRJ-3P-WHQSGRJ-3P-TWHQSGRJ-3P-1WHQSGRJ-3P-1TWH



Available Standard Model Numbers


369313f 11 05.26.17

®

Job Name:

Job Number:

Model Numbers:



GRAFIK Eye QS Wireless Control Unit (continued)Custom Color Options and Model Numbers

•YoumustorderaBaseUnitandaFaceplateKit•SeeStandardColorCombinationspageforfaceplate,stripe,andbuttoncolors

Base Unit

QSGRJ– P

Number ofZones

3 = 3 zones4 = 4 zones6 = 6 zones

Phase Control Triac

Prefix

Example:QSGRJ-6P6-zone base unit.

QSGFP– – Number of

Shade Columns

Omit = none1 = 1 column2 = 2 columns3 = 3 columns

Faceplate Prefix

Architectural Matte Finishes (standard) (ship in 48 hours)White WHIvory IVBeige BEGray GRBrown BRBlack BLAlmond ALLight Almond LA

Architectural Metal FinishesBrightBrass BBBrightChrome BCBrightNickel BNSatinBrass SBSatin Chrome SCSatin Nickel SNAntiqueBrass QBAntiqueBronzeQZ

Anodized Aluminum FinishesClear CLABlack BLABrass BRA

Satin Color Matte FinishesSnow SWBiscuit BIEggshell ESTaupe TPMidnight MNLimestone LSStone STDesertStone DSTerracotta TCHot HTGoldstone GSPalladium PDPlum PLTurquoise TQBluestone BGSea Glass SGGreenbriar GBSienna SIMerlot MRMocha Stone MS

Omit = Same as unit

T = Translucent

Faceplate Custom Color/Finish Code

TopDoorColor

Example:QSGFP-2IV-EGNIvory faceplate kit with 2 shade columns and general engraving.

Faceplate Kit (includes coordinating stripe and buttons)

Keypad Engraving Code

Omit = Unengraved Ships with engraving certificate that customer can redeem at no charge

EGN = General Engraving

NST = Non-Standard Text Engraving Visit the GRAFIK Eye QS website at: www.lutron.com/grafikeyeqs for custom engraving forms. Submit completed form with order and unit will ship engraved as specified by customer

OK

1 2 3 4 5 69 10 11 12 13 14 7 815 16

9-161-8

1

2

3

4

Off

OK

1 2 3 4 5 69 10 11 12 13 14 7 815 16

9-161-8

Open

Preset

Close

Lighting keypad

Shade column


369313f 12 05.26.17

®

Job Name:

Job Number:

Model Numbers:



GRAFIK Eye QS Wireless Control Unit (continued)Custom Options and Model Numbers

•SeepreviouspagesforStandardandOtherCustomModelNumbers•SeeStandardColorCombinationspageforfaceplate,stripe,andbuttoncolors

Custom Button Kit

QSGS– Stripe Kit

Prefix

Example:QSGS-WHStripe kit with white stripe.

QSGB– – – ButtonConfiguration

3BRL=3-buttonwithraise/lower (shade column)

5B=5-button(lightingkeypad

Custom ButtonKit

Prefix

Architectural Matte FinishesWhite WHIvory IVBeige BEGray GRBrown BRBlack BLAlmond ALLight Almond LA

Satin Color Matte FinishesSnow SWBiscuit BIEggshell ESTaupe TP

ButtonKitCustomColor/FinishCode

Example:QSGB-5B-WH-EGNWhite 5-button, lighting keypad button kit with general engraving.

Custom Stripe Kit

Keypad Engraving Code

Omit = Unengraved Ships with engraving certificate that customer can redeem at no charge

EGN = General Engraving

NST = Non-Standard Text Engraving Visit the GRAFIK Eye QS website at: www.lutron.com/grafikeyeqs for custom engraving forms. Submit completed form with order and unit will ship engraved as specified by customer

OK

1 2 3 4 5 69 10 11 12 13 14 7 815 16

9-161-8

1

2

3

4

Off

OK

1 2 3 4 5 69 10 11 12 13 14 7 815 16

9-161-8

Open

Preset

Close

Lighting keypad

Shade column

Architectural Matte FinishesWhite WHIvory IVBeige BEGray GRBrown BRBlack BLAlmond ALLight Almond LA

Architectural Metal FinishesBrightBrass BBBrightChrome BCBrightNickel BNSatinBrass SBSatin Chrome SCSatin Nickel SNAntiqueBrass QBAntiqueBronzeQZ

Anodized Aluminum FinishesClear CLABlack BLABrass BRA

Satin Color Matte FinishesSnow SWBiscuit BIEggshell ESTaupe TPMidnight MNLimestone LSStone STDesertStone DSTerracotta TCHot HTGoldstone GSPalladium PDPlum PLTurquoise TQBluestone BGSea Glass SGGreenbriar GBSienna SIMerlot MRMocha Stone MS

Stripe Custom Color/Finish Code


369313f 13 05.26.17

®

Job Name:

Job Number:

Model Numbers:



GRAFIK Eye QS Wireless Control Unit Standard Color Combinations

•SeepreviouspagesforStandardandCustomModelNumbersFaceplate is comprised of a top and bottom. The bottom will always be the color indicated under “faceplate.” The top may be the same color or translucent. Use the chart for faceplates that have the same color top and bottom. If a translucent lid is chosen, the stripe will automatically be the same color as the bottom lid.

Example:If you order QSGRJ-4P-1WH, your GRAFIK Eye QS with 4 lighting zones and 1 shade zone will have a white faceplate (both top and bottom), gray stripe, and white buttons.

LUTRON

1

2

3

4

Off

Preset

Close

Open

F (faceplate)

S (stripe)

B(buttons)

F (faceplate)

Suffix Faceplate (F) Stripe (S) Button (B)Architectural MatteWH White Gray WhiteIV Ivory Beige IvoryBE Beige Ivory BeigeGR Gray Black GrayBR Brown Black BrownBL Black Gray BlackAL Almond Light Almond AlmondLA Light Almond Almond Light AlmondArchitectural MetalBB BrightBrass Black BlackBC BrightChrome Black BlackBN BrightNickel Black BlackSB SatinBrass Black BlackSC Satin Chrome Black BlackSN Satin Nickel Black BlackQB AntiqueBrass Black BlackQZ AntiqueBronze Black BlackAnodizedCLA Clear Black BlackBLA Black Black BlackBRA Brass Black BlackSatin MatteMN Midnight Gray BlackTP Taupe Gray TaupeSW Snow Gray SnowES Eggshell Beige EggshellBI Biscuit Eggshell BiscuitLS Limestone Gray GrayST Stone Gray GrayDS DesertStone Taupe TaupeTC Terracotta Taupe TaupeBG Bluestone Gray GrayHT Hot Taupe TaupeMR Merlot Taupe TaupeSI Sienna Brown BrownGB Greenbriar Gray GraySG Sea Glass Gray GrayMS Mocha Stone Taupe TaupeGS Goldstone Ivory IvoryPD Palladium Gray GrayPL Plum Taupe TaupeTQ Turquoise Gray Gray


369313f 14 05.26.17

®

Job Name:

Job Number:

Model Numbers:



Wiring DiagramsTerminations

12

34

12

AB

C

123456LN

Load wiring

Communication link

Occupancy sensor/contact closure input and 24 V- power

IR input


369313f 15 05.26.17

®

Job Name:

Job Number:

Model Numbers:



Power Group Wiring Example•OntheQSlink,therearedevicesthatsupplypoweranddevicesthatconsumepower.EachdevicehasaspecificnumberofPowerDrawUnits(PDUs)iteithersuppliesorconsumes.APowerGroupconsistsofonedevicethatsuppliespowerandone or more devices that consume power; each Power Group may have only one power-supplying device. Refer to the QS LinkPowerDrawUnitsspecificationsubmittal(LutronP/N369405)formoreinformationconcerningPDUs.

•WithinPowerGroupsontheQSlink,connectall4terminals(1,2,3,and4),shownbytheletterAinthediagram.BetweendevicesontheQSlinkthatsupplypower,connectonlyterminals1,3,and4(NOTterminal2),shownbytheletterBonthediagram.

•WiringcanbeT-tappedordaisy-chained.

LUTRON

LUTRON

LUTRON

LUTRON

LUTRONLUTRON

Power Group 1

Power Group 2

Power Group 3

(Donotconnectterminal2:24V-)



GRAFIK Eye QS control unit SuppliesPDUs

Energi Savr Node QS unit SuppliesPDUs

QS Power Supply SuppliesPDUs

Control Interfaces ConsumePDUs

Control Interfaces ConsumePDUs

Quantum Processor SuppliesPDUs

Wallstations ConsumePDUs



QS Sensor Module with wired Occupancy SensorConsumesPDUs

Wireless Occupancy SensordoesnotconsumePDUs

A

A

A

B

B

B

AConnect all 4 terminals within a power group:1: Common 2: 24 V- 3 and 4: Data

BConnect only 3 terminals between power groups:1: Common 2: 24 V-Donot connect 3 and 4: Data


369313f 16 05.26.17

®

Job Name:

Job Number:

Model Numbers:



Mounting

•Fitsintoa4-gangU.S.backbox,3½in(90.4mm)deep(LutronP/N245254)or3in(76.2mm)deep(LutronP/N241400)

Line Voltage Wiring

•Pullpowerwiringfromdistributionpanelandtolightfixtures.•Eachlinevoltageterminalcanacceptone12AWG(4.0mm2) wire.•ConsultLutronfornon-dimrelaywiringand/orloadsideemergencytransferwiring.

GRAFIK Eye® QS control unit

Hinged top lid

Mounting screws (4)

Hinged bottom lid

Distribution Panel

120 – 127 V~ 50/60 Hzor

220 – 240 V~ 50/60 Hz

1 2 3 4 5 6 L N

To Load 1

To Load 2

To Load 3

To Load 4

To Load 5

To Load 6

L N D

Rear of QS control unit

Line voltage (Hot/Live) is labeled L


369313f 17 05.26.17

®

Job Name:

Job Number:

Model Numbers:



IEC PELV/NEC® Class 2 QS System Wiring

•Wiringcanbedaisy-chainedorT-tapped.•Wiringmustberunseparatelyfromline/mainsvoltage.•Totallengthofcontrollinkmustnotexceed2000ft(610m).

Wire Sizes (check compatibility in your area)

QS Link Wiring Length Wire Gauge Lutron Cable Part Number

Less than 500 ft (153 m)

Power (terminals 1 and 2)1 pair 18 AWG (1.0 mm2) GRX-CBL-346S(non-plenum)

GRX-PCBL-346S(plenum)Data(terminals3and4)1 twisted, shielded pair 22 AWG (0.5 mm2)

500 to 2000 ft (153 to 610 m)Power (terminals 1 and 2)1 pair 12 AWG (4.0 mm2) GRX-CBL-46L(non-plenum)

GRX-PCBL-46L(plenum)Data(terminals3and4)1 twisted, shielded pair 22 AWG (0.5 mm2)

Daisy-Chain Wiring Example

T-Tap Wiring Example

LUTRON

LUTRON

LUTRON

LUTRONLUTRON

LUTRON

LUTRON

LUTRON

LUTRON

LUTRON

LUTRON LUTRON LUTRON

LUTRON

GRAFIK Eye QS Control Unit

Sivoia QS Shade

seeTouch QS Wallstations

Sivoia QS Smart PanelLUTRON

LUTRON

LUTRON

LUTRONLUTRON

LUTRON

LUTRON

LUTRON

LUTRON

LUTRON

LUTRON LUTRON LUTRON

LUTRON

Sivoia QS Smart Panel

GRAFIK Eye QS Control Unit

Sivoia QS Shade

seeTouch QS Wallstations

)Lutron, Lutron, GRAFIK Eye, Pico, Sivoia, Quantum, seeTouch, Softswitch, RTISS Equipped, Clear Connect, Tu-Wire, and EcoSystem are trademarks of Lutron Electronics Co., Inc., registered in the U.S. and other countries.

Radio Powr Savr, RadioRa 2, and Energi Savr Node is a trademark of Lutron Electronics Co., Inc.

NEC is a registered trademark of National Fire Protection Association, Quincy, Massachusetts.

UL is a trademark of UL LLC.

AdvanceandMarkXareregisteredtrademarksofPhilipsElectronicsNorth America Corporation.

Documents

GRAFIK Eye QS Wireless Control Unit SPEC (369313) mm orol 369313f 1 05.26.17 ® Job Name: Job Number: Model Numbers: SPECIFICATION SUMITTAL Page Wireless Control Unit GRAFIK Eye QS