Quick Start Guide Gen-II ELD/EOBR

FOR SUPPORT, PLEASE CONTACT TECHNICAL SUPPORT @ 800-327-1342 ext. 8223

Ensure the harness is securely attached into the ELD/EOBR.

Secure the ELD/EOBR in a position where the driver can see the lights, but is out of the way. Use the adhesive strips provided (or if you choose, place screws through the 2 bracket mounts on either side of the ELD/EOBR) to mount the ELD/EOBR.

You may mount the handheld device within the vehicle as well.

Your installation is complete! Your vehicle is now ready to take advantage of the many features of KellerMobile™.

21

22

23

24

“EOBR Disconnected” instead of “EOBR ### Online”: a. Verify harness is securely connected. • Select “EOBR Disconnected” icon. Follow step 12 through step 13. b. Is the device battery low? c. Is Bluetooth turned on?

Unable to Login: a. Verify username/password. b. Requires network connectivity if logging in for the first time.

Prompt for location at a duty-status change: a. Driver manually enters location once prompted. b. Verify connection between device and ELD/EOBR. c. Verify network connectivity.

Cannot successfully submit logs: a. Is there a network connection? b. If not, wait until the next time the driver logs in, then Submit. Cannot view driver activity within Encompass: a. Is the driver logged into the KellerMobile™ application? b. Is the driver connected to the ELD/EOBR? c. Is there a network connection?

D Completing the Setup

E Troubleshooting

Quick Start Guide Gen-II ELD/EOBR

FOR SUPPORT, PLEASE CONTACT TECHNICAL SUPPORT @ 800-327-1342 ext. 8223

1

2

3

4

5

A What’s In The Box

B Connecting The Hardware

ElectronicLogging Device

(ELD/EOBR)

WiringHarnesses

6-pin 9-pin

OBD

Bit, Alcohol Swab,Adhesive Strips

Locate the diagnostic port in vehicle & detach existing cable from port.

Using your vehicle-specific 6-pin, 9-pin or OBD wiring harness, plug the male end of the Y-connector harness into the now open diagnostic port.

Route the wiring harness to ELD/EOBR installation location.Plug your vehicle’s diagnostic cable into the female end of the Y-connector.

Connect the “fastener” end of the harness (with locking screw) to the ELD/EOBR.

If you’re receiving power, the lights on the ELD/EOBR will flash. If you are not receiving power at all, ensure harness is securely connected.

Example: 9-pin Harness (Your vehicle may have a 6-pin or OBD harness)

1

Male Female

Fastner

2 3

4

Diagnostic Port

505936 (Rev. 01/14)

On EOBR Configuration screen: a. Enter your vehicle number in the “Tractor Number” field. b. Select “AUTO DETECT DATABUS” in the “Engine Data Bus” field and select “OK.”

You may be prompted to “Pair” to this new Tractor Number, select “OK.”

Enter “Trailer Number” & “Shipment Information”, select “OK.”

On Odometer Calibration screen, enter dashboard odometer number. The engine must be ON to perform this step.

On application Home screen, you will see your name, location, current status and date/time in the green banner at the top. You should also see “EOBR ### ONLINE” in lower left.

Once ONLINE, go to “Menu,” “System Menu,” “Diagnostics,” “Read EOBR Data.” a. Ensure that odometer and GPS coordinates are valid. If these are not valid, there is a chance that either the Engine Data Bus is configured incorrectly and/or the ELD is not receiving a GPS signal. b. If you do not see valid stats for speedometer, odometer, and tachometer, then go to “Menu,” “System Menu,” “Diagnostics,” “Set EOBR Config” and perform this step again. Verify that EOBR Data is accurate.

Once data is verified, select the “Log Off” button, and then select “Submit.”

Quick Start Guide Gen-II ELD/EOBR

FOR SUPPORT, PLEASE CONTACT TECHNICAL SUPPORT @ 800-327-1342 ext. 8223

14

15

16

17

18

19

20

C Completing the Setup

FOR SUPPORT, PLEASE CONTACT TECHNICAL SUPPORT @ 800-327-1342 ext. 8223

Start vehicle. Engine must be ON for diagnostic port detection.

Turn on handheld device (with KellerMobile™ software loaded).

Pair/connect via Bluetooth to the ELD/EOBR.

Launch KellerMobile™ application.

Enter Activation Code, select “Activate.”

On the Login screen, enter username and password, and select “OK.”

On Perform EOBR Discovery screen, select “Discover.” You may be prompted to ‘Pair’ with your ELD/EOBR, select “OK.” Select drop down menu to choose your ELD/EOBR (serial number).

If handheld device will typically be connected to this ELD/EOBR, choose “Set Default EOBR” checkbox. Select “Activate.”

6

7

8

10

11

12

13

9