Talha Ansari,Technical Approach/VHDL implementation

Heather Garnell, Technical Approach/VHDL implementation

Anamika Shams, Testing Requirements/Implementation

• Image morphing is a useful and widely recognized visualization technique.  Thus there is interest in and research conducted in this area.

• Image morphing techniques can generate compelling 2-D transitions between images and thus will add an element to fun to the entire project development process.

• To implement image morphing on the ML507 test board using both the xilinx FPGA and the PPC 440

• From Iowa State CprE583 Fall 2011 lecture 12

• The final product will include two similar images and a final morphed image similar to the images you see below.

• The concept of Barycentric Coordinates can be used in an image morphing application

http://www.cs.washington.edu/homes/ankit/course_projects/files/DIP/A2_web/marked6.jpg

compute_ABCts

find_bary_coordinate

compute_alpha

main

write

bary

read

compute_gamma

compute_beta get_tri_area

•Compute_ABCts: This function compute time interpolation of ABC_0 and ABC_1 for AtBtCt triangle •by looping through 8 triangle, 3 points of each triangle and the 2 coordinate of the each triangle•Get_Tri_Area: This method is getting the area of the corresponding point P1, P2 and P3 of the new •triangle.•Compute_Alpha: This function compute the new triangle area in regards to ABC triangle and PBC •triangle•Compute_Beta: This function compute the new triangle area in regards to ABC triangle and PAC•triangle•Compute_Gamma: This function compute the new triangle area in regards to ABC triangle and PAB•triangle.•Find_Bary_Coordinate: This function find two coordinate points x and y from the ABC triangle area.•Bary: This method is computing the morphed triangle at time t where due to the affine invariant •property, the corresponding point Po in triangle AoBoCo and PI in triangle A,BICI are Po = atAo + •BtBo + YtCO and PI = atA I + BtBI + YtC" respectively. If the colors of Po and PI are I0 and I1,•respectively, the color at Pt will be computed same as simply using this function It = (l-t)Io + tIl. •Therefore, every pixel of triangle AtBtCt is interpolated from its initial color in triangle AoBoCo and its•final color in triangle AIBICI.•Read: This method open the bmp file and read the header and the color of two images files and then•close the file.•Write: This function open the final morphed image file and write the morphed image.

• To reuse MP3 architecture as much as possible• Offload PPC with pixel morphing

• Load 120 bits (5 pixels) from each picture in two consecutive loads• Take average of each pixel element• Send modified data back to PPC

• Step 1: Design C code on local computer and test out• Step 2: Design VHDL merging function and test out• Step 3: Integrate C code on PPC• Step 4: Integrate VHDL code by offloading pixel merging to

FPGA• Step 5: Test system out

• Complete C code implementation

alpha = compute_alpha(ABC_t, uv); beta = compute_beta (ABC_t, uv); gamma = compute_gamma(ABC_t, uv);

// Let Pt be a point of triangle AtBtCt. // Its barycentric coordinate with respect to triangle AtBtCt, can be found as // Pt = ætAt + ßtBt + YtCt where æt/=0, ßt/=0, Yt/=0, æt+ßt+Yt=1 Pt = find_bary_coordinate(alpha, beta, gamma, ABC_t); // From the coordinate (æt, ßt, Yt) of point Pt, due to the affine // invariant property, the corresponding point // P0 in triangle AøBøCø = ætAø + ßtBø + YtCø // P1 in triangle A1B1C1 = ætA1 + ßtB1 + YtC1 P0 = find_bary_coordinate(alpha, beta, gamma, ABC_0); P1 = find_bary_coordinate(alpha, beta, gamma, ABC_1);

// If the colors of P0 and P1 are I0 and I1, respectively, // the color at Pt is simply: It = (1-t)I0 + tI1

// Compute It for red, green, and blue pixels temp_red = (1.0-t)*(float)(I0.red) + t*(float)(I1.red); // Red temp_grn = (1.0-t)*(float)(I0.grn) + t*(float)(I1.grn); // Green temp_blu = (1.0-t)*(float)(I0.blu) + t*(float)(I1.blu); // Blue SINGLE_PIXEL It = { (int)(temp_red), (int)(temp_grn), (int)(temp_blu) };

It is important for images to be the same size and orientation.

Source images were chosen because they met this criteria.

• Each of the two input images broken into eight triangles

Final morphed image based on the previous slide’s two images

• VHDL implementation complete

• Currently at this step of integration• Minor issues with integration of current c code into out echo.c

• Next step

• This is where magic happens!!!

Ching-Kuang Shene. "Barycentric Coordinates and Morphing,” Department of Computer Science. Michigan Technological University. April 19, 2003.- This is a practical guide for implementing barycentric coordinates into an image morphing application.  T. Balercia, A. Zitti, H. Francesconi, S. Orcioni and M. Conti. "FPGA Implementations of a Simplified Retinex Image Processing Algorithm." IEEE 2006.

• Resolve issue with final morphing of pixel data within c code• as this the morphing algorithm itself was not the purpose of the

project, we chose to resolve this between now and final submission

• Complete integration effort

• Modify documentation based on any recent changes to project design or implementation

• Complete writing the final report

• Set times when the entire group can meet to discuss topics proved to be difficult with work schedules and family issues.

• Use of chat programs was very helpful to keep communication lines open

• Use of tools to keep documentation in a common location was helpful (Google docs and Google sites)

• Check for integration issues early on is important

Thank you!