Upload
phunganh
View
220
Download
0
Embed Size (px)
Citation preview
Feel the differenceFordFusionOwner's handbook
The information contained in this publication was correct at the time of going to print. In theinterest of development the right is reserved to change specifications, design or equipmentat any time without notice and without incurring any obligations. This publication, or partthereof, may not be reproduced nor translated without our approval. Errors and omissionsexcepted.
© Ford Motor Company 2007
All rights reserved.
Part number: 8S6J-19A321-BDA (CG3441en) 11/2007 20071112092528
IntroductionAbout this handbook........................5Symbols glossary..............................5Parts and accessories......................5
Quick startQuick start..........................................8
Child safetyChild seats........................................19Booster cushions............................20Child seat positioning......................21Child safety locks............................22
Occupant protectionPrinciple of operation.....................23Fastening the seat belts................26Seat belt height adjustment..........26Using seat belts during
pregnancy.....................................27Disabling the passenger
airbag.............................................27
Keys and remotecontrols
General information on radiofrequencies..................................29
Programming the remotecontrol...........................................29
Changing the remote controlbattery...........................................30
LocksLocking and unlocking...................32
Engine immobiliserPrinciple of operation.....................34Coded keys.....................................34Arming the engine immobiliser.....34Disarming the engine
immobiliser...................................34
AlarmArming the alarm.............................35Disarming the alarm........................35
Steering wheelAdjusting the steering wheel.........36Audio control...................................36
Wipers and washersWindscreen wipers.........................38Windscreen washers.....................39Rear window wiper and
washers........................................39Adjusting the windscreen washer
jets.................................................40Checking the wiper blades...........40Changing the wiper blades............41
LightingLighting control................................42Front fog lamps...............................43Rear fog lamps................................44Headlamp levelling..........................44Hazard warning flashers................45Direction indicators.........................45Interior lamps...................................45Removing a headlamp...................46Changing a bulb..............................47
1
Table of contents
Bulb specification chart..................52
Windows and mirrorsElectric windows.............................53Exterior mirrors................................53Electric exterior mirrors..................54Interior mirror...................................55
InstrumentsGauges.............................................56Warning lamps and indicators.......57
Information displaysGeneral information.........................61Personalised settings.....................63Information messages...................63
Climate controlPrinciple of operation......................67Air vents............................................67Manual climate control...................68Automatic climate control..............70Heated windows and mirrors........72Auxiliary heater................................72Sunroof.............................................73
SeatsSitting in the correct position.........74Manual seats....................................74Rear seats........................................76Head restraints................................76Heated seats....................................77Front seat armrest..........................78
Convenience featuresSun visors.........................................79Cigar lighter......................................79Glove box.........................................79Storage compartments.................79Rear seat armrest............................81
Starting the engineGeneral information........................82Ignition switch..................................82Starting a petrol engine..................82Starting a diesel engine..................84Switching off the engine................84
Fuel and refuellingSafety precautions..........................85Fuel quality - Petrol.........................85Fuel quality - Diesel.........................85Catalytic converter.........................85Fuel filler flap.....................................86Refuelling..........................................86Fuel consumption...........................86Technical specifications.................87
TransmissionManual transmission.......................88Automatic transmission - 4-Speed
Automatic Transmission(4F27E)..........................................89
BrakesPrinciple of operation.....................92Hints on driving with ABS...............92Parking brake..................................93
2
Table of contents
Stability controlPrinciple of operation.....................94Using stability control......................95
Parking aidPrinciple of operation.....................96Using the parking aid......................96
Load carryingGeneral information........................98Luggage covers..............................98Roof racks and load carriers.........98
TowingTowing a trailer................................99Detachable tow ball........................99
Driving hintsGeneral driving points...................103Running-in......................................103
Status after acollision
Fuel cut-off switch.........................104Inspecting safety system
components...............................105
FusesChanging a fuse............................106Fuse labels......................................106Fuse box locations........................108
Vehicle recoveryTowing points.................................109
Towing the vehicle on fourwheels.........................................109
MaintenanceGeneral information........................111Opening and closing the
bonnet..........................................112Engine compartment overview -
1.25L Duratec-16V (Sigma)/1.4LDuratec-16V (Sigma)/1.6LDuratec-16V (Sigma)..................113
Engine compartment overview -1.4L Duratorq-TDCi (DV)Diesel............................................115
Engine compartment overview -1.6L Duratorq-TDCi (DV)Diesel............................................117
Engine oil check.............................118Engine coolant check....................119Brake and clutch fluid check.......120Power steering fluid check..........120Washer fluid check........................121Technical specifications................122
Vehicle careCleaning the exterior....................125Cleaning the interior......................126Repairing minor paint damage.....126
Vehicle batteryBattery care....................................127Using booster cables....................127
Wheels and tyresGeneral information......................129Changing a road wheel................129Tyre repair kit..................................133
3
Table of contents
Tyre care.........................................139Using winter tyres..........................139Using snow chains........................139Technical specifications................140
TelephoneGeneral information......................142Telephone setup...........................142Bluetooth setup.............................144Telephone controls.......................145Using the telephone - Vehicles
Without: Navigation System.....146Using the telephone - Travel Pilot
EX.................................................149
Voice controlPrinciple of operation....................152Using voice control.......................153Audio unit commands..................153Telephone commands.................158Navigation system
commands.................................163Climate control commands.........163
Vehicle identificationVehicle identification plate............166Vehicle identification number
(VIN).............................................166Engine number..............................166
Technical specific-ations
Weights...........................................167Dimensions.....................................169
Type approvalsType approvals...............................173
AppendicesElectromagnetic compatibility.....176Type approvals...............................177
4
Table of contents
ABOUT THIS HANDBOOK
Thank you for choosing Ford. Werecommend that you take some timeto get to know your vehicle byreading this handbook. The more thatyou know about it, the greater thesafety and pleasure you will get fromdriving it.
Note: This handbook describesproduct features and optionsavailable throughout the range,sometimes even before they aregenerally available. It may describeoptions not fitted to your vehicle.
Note: Always use and operate yourvehicle in line with all applicable lawsand regulations.
Note: Pass on this handbook whenselling your vehicle. It is an integralpart of the vehicle.
SYMBOLS GLOSSARY
Symbols in this handbook
WARNING
You risk death or serious injuryto yourself and others if you do
not follow the instructions highlightedby the warning symbol.
CAUTION
You risk damaging your vehicleif you do not follow the
instructions highlighted by the cautionsymbol.
Symbols on your vehicle
When you see these symbols, readand follow the relevant instructionsin this handbook before touching orattempting adjustment of any kind.
PARTS ANDACCESSORIES
Now you can be sure thatyour Ford parts are Fordparts
Your Ford has been built to thehighest standards using high qualityFord Original Parts. As a result, youcan enjoy driving it for many years.
Should the unexpected occur and amajor part needs replacing, werecommend that you accept nothingless than Ford Original Parts.
The use of Ford Original Partsensures that your vehicle is repairedto its pre-accident condition andmaintains its maximum residual value.
Ford Original Parts match Ford'sstringent safety requirements andhigh standards of fit, finish andreliability. Quite simply, they representthe best overall repair value, includingparts and labour costs.
5
Introduction
Now it is easier to tell if you havereally been given Ford Original Parts.The Ford logo is clearly visible on thefollowing parts if they are FordOriginal Parts. If your vehicle has tobe repaired, look for the clearly visibleFord branding and make sure thatonly Ford Original Parts have beenused.
Look for the Ford logo onthe following parts
Sheet metal
• Bonnet• Wings• Doors• Tailgate
E89937
Bumper and radiator grille
• Radiator grille• Front and rear bumper
Glass
• Rear window• Side glass• Windscreen
E89939
Lighting
• Rear lamps• Headlamp
6
Introduction
E89940
7
Introduction
QUICK START
Instrument panel overview - LHD
A
V T R MNOPQSU
B D F G HE KJI LC
E89017
Window demister.A
Air vent.B
Luggage compartment release.C
Main beam, direction indicators, headlamp flasher and informationdisplay controls.
D
Instrument cluster.E
Wiper lever.F
Heated windscreen switch.G
Heater rear window switch.H
Storage tray.I
8
Quick start
Hazard warning flasher switch.J
Stability control switch or coin holder.K
Airbag deactivated warning lamp or coin holder.L
Audio or navigation unit. See separate handbook.M
Climate controls.N
Interior temperature sensor.O
Ignition switch.P
Horn.Q
Steering wheel adjustment lever.R
Audio controls.S
Storage compartment.T
Headlamp levelling control.U
Lighting controls.V
9
Quick start
Instrument panel overview - RHD
A
V T R MNOPQSU
B D F G HE KJI LC
E89018
Stability control switch or coin holder.A
Airbag deactivated warning lamp or coin holder.B
Hazard warning flasher switch.C
Storage tray.D
Heated windscreen switch.E
Heater rear window switch.F
Main beam, direction indicators, headlamp flasher and informationdisplay controls.
G
Instrument cluster.H
Wiper lever.I
Luggage compartment release.J
10
Quick start
Air vent.K
Window demister.L
Lighting controls.M
Headlamp levelling control.N
Storage compartment.O
Ignition switch.P
Steering wheel adjustment lever.Q
Horn.R
Audio controls.S
Interior temperature sensor.T
Climate controls.U
Audio or navigation unit. See separate handbook.V
Adjusting the steeringwheel
E70358
WARNING
Never adjust the steering wheelwhen the vehicle is moving.
Engine idle speed afterstarting
The engine may idle at a higherspeed than normal immediately afterstarting from cold. See Startingthe engine (page 82).
Warning lamps andindicators
ABS warning lamp
Airbag warning lamp
Brake system warning lamp
11
Quick start
Direction indicator
Door open warning lamp
Engine warning lamp
Engine and transmissionwarning lamp
Front fog lamp indicator
Frost warning lamp
Glow plug indicator
Headlamp indicator
Ignition warning lamp
Low fuel level warning lamp
Main beam indicator
Oil pressure warning lamp
Overdrive indicator
Power steering warninglamp
Powertrain warning lamp
Rear fog lamp indicator
Stability control (ESP)warning lamp
Information displays
Type 1 information display
E91003
E D
A
BC
Distance to empty or clockA
TripmeterB
OdometerC
Select buttonD
Reset buttonE
Press the select button to scrollthrough the displays.
12
Quick start
Type 2 information display
A
F
BC
E
E91005
D
Selected gearA
Clock, radio station or CDtrack
B
Outside air temperatureC
TripmeterD
OdometerE
Message indicatorF
E70436
Press the button to scroll through thedisplays and hold the button to rest,select a submenu or change asetting. The information display willtell you whether a short press of thebutton or long press of the button isrequired for the various options.
Personalised settings
You can change the settings ofvarious functions through theinformation display.• Unlocking the doors with the
remote control.• Direction indicators.• Audio display.• Hazard warning flashers.• Audible warnings.• Language.
Defrosting and demistingthe windscreen
Vehicles with manual climatecontrol
E90447
If necessary, switch the heatedwindows on.
13
Quick start
E72506
E72507
Vehicles with automaticclimate control
E70446
Cooling the interior quickly
Vehicles with manual climatecontrol
E90451
Vehicles with automaticclimate control
E72153
Locking and unlocking thedoors with the remotecontrol
E87379
A B C
UnlockA
LockB
Luggage compartment lidunlock
C
Locking the doors
Press button B once.
Double locking the doors
Press button B twice within threeseconds.
14
Quick start
Unlocking the luggagecompartment lid
Press button C twice within threeseconds.
Audio unit
Automatic volume control(AVC)
When available, automatic volumecontrol (AVC) adjusts the volumelevel to compensate for engine noiseand road speed noise.
1. Press the MENU buttonrepeatedly until an AVC displayappears.
2. Use the left or right arrow button,to adjust the AVC setting.
Changing the date and time
1. Press the CLOCK button todisplay the date and time.
2. Use the left or right arrow buttonto select the date or time valuethat you wish to change. Theselected value will flash in thedisplay.
3. Turn the volume control tochange the selected date or timevalue.
4. Use the left or right arrow buttonto select additional date or timevalues that you wish to change.
5. Turn the volume control tochange the selected date or timevalue.
6. Press the CLOCK button to exitand save the new date and time.
Autolamps
E72162
Note: If you have switchedautolamps on, you can only switchthe main beam on when autolampshas switched the headlamps on.
The headlamps will come on and gooff automatically depending on theambient light.
Home safe lighting
Vehicles without autolamps
Switch the headlamps on and thenswitch them off within two seconds.
Vehicles with autolamps
a. Switch autolamps on and thenswitch them off within twoseconds.
b. Switch autolamps off and thenswitch them on within twoseconds.
15
Quick start
Welcome lighting
The side and tail lamps will come onwhen you unlock the doors with theremote control. They will switch offautomatically after a short time.
Autowipers
E72173
2
High sensitivity1
Low sensitivity6
Electric folding mirrors
E72184
Automatic folding
The mirrors will fold automaticallywhen you lock the vehicle with theremote control. The mirrors will unfoldwhen you unlock the vehicle with thekey or the remote control.
Glove box
E91002C
BB
A
Card holderA
Coin holdersB
Pen or pencil clipC
16
Quick start
Creating a level load floor
E91009
1 2 3
1. Lift the seat cusion.
2. Pull the locking lever and push theseatback forwards.
3. Press the rear of the seatbackdownwards.
Storage box
E91010
2
1
3
A storage box is located under thepassenger seat cushion.
17
Quick start
Storage pockets
E91011
A
B
Driver seatA
Rear seatB
18
Quick start
CHILD SEATS
E68916
WARNINGSSecure children that are lessthan 150 centimetres tall or less
than 12 years of age in a suitable,approved child restraint, in the rearseat.
Original text according to ECER94.01: Extreme Hazard! Do not
use a rearward facing child restrainton a seat protected by an air bag infront of it!
Read and follow themanufacturer’s instructions
when you are fitting a child restraint.
Do not modify child restraints inany way.
Do not hold a child on your lapwhen the vehicle is moving.
Do not leave unattendedchildren in your vehicle.
WARNINGSIf your vehicle has been involvedin an accident, have the child
restraints checked by properlytrained technicians.
Note: Mandatory use of childrestraints varies from country tocountry.
A choice of ECE approved childrestraints which have beenspecifically tested and approved foryour vehicle are available from yourDealer.
Child restraints for differentmass groups
Use the correct child restraint asfollows:
Baby safety seat
E68918
Secure children that weigh less than13 kilogrammes in a rearward facingbaby safety seat in the rear seat.
19
Child safety
Child safety seat
E68920
Secure children that weigh between13 and 18 kilogrammes in a childsafety seat in the rear seat.
BOOSTER CUSHIONS
WARNINGSDo not install a booster seat ora booster cushion with only the
lap strap of the seat belt.
Do not install a booster seat ora booster cushion with a seat
belt that is slack or twisted.
Do not put the seat belt underyour child’s arm or behind its
back.
Do not use pillows, books ortowels to boost your child’s
height.
Make sure that your children sitin an upright position.
WARNINGSSecure children that weigh morethan 15 kilogrammes but are
less than 150 centimetres tall in abooster seat or a booster cushion.
Booster seat
E70710
We recommend that you use abooster seat that combines acushion with a backrest instead of abooster cushion only. The raisedseating position will allow you toposition the shoulder strap of theadult seat belt over the centre of yourchild’s shoulder and the lap straptightly across its hips.
20
Child safety
Booster cushion
E68924
CHILD SEATPOSITIONING
WARNING
When using a forward facingchild seat on the rear seat,
always remove the head restraintfrom that seat.
Mass group categoriesSeating positions
IIIIII0+0
22 - 36kg
15 - 25kg
9 - 18 kgUp to 13kg
Up to 10kg
U¹U¹U¹XXFront passengerseat with airbag ON
UUUUUFront passengerseat with airbag OFF
UUUUURear seats
X Not suitable for children in this mass group.
U Suitable for universal category child restraints approved for use in this massgroup.
U¹ Suitable for universal category child restraints approved for use in this massgroup. However, we recommend that you secure children in a governmentapproved child restraint, in the rear seat.
21
Child safety
CHILD SAFETY LOCKS
WARNING
You cannot open the doorsfrom inside if you have put the
child safety locks on.
E73697
A
B
LockA
UnlockB
22
Child safety
PRINCIPLE OFOPERATION
Airbags
WARNINGSDo not modify the front of yourvehicle in any way. This could
adversely affect deployment of theairbags.
Original text according to ECER94.01: Extreme Hazard! Do not
use a rearward facing child restrainton a seat protected by an airbag infront of it!
Wear a seat belt and keepsufficient distance between
yourself and the steering wheel. Onlywhen you use the seat belt properly,can it hold you in a position thatallows the airbag to achieve itsoptimum effect. See Sitting in thecorrect position (page 74).
Have repairs to the steeringwheel, steering column, seats,
airbags and seat belts carried out byproperly trained technicians.
Keep the areas in front of theairbags free from obstruction.
Do not affix anything to or over theairbag covers.
Do not poke sharp objects intoareas where airbags are fitted.
This could damage and adverselyaffect deployment of the airbags.
Use seat covers designed forseats with side airbags. Have
these fitted by properly trainedtechnicians.
Note: You will hear a loud bang andsee a cloud of harmless powderyresidue if an airbag deploys. This isnormal.
Note: Only wipe airbag covers witha damp cloth.
The restraint system comprises:• a driver airbag• a front passenger airbag• side airbags• curtain airbags• a driver seat belt pretensioner• a front passenger seat belt
pretensioner• crash sensors• an airbag warning lamp• a seat belt reminder• an electronic control and
diagnostic unit.
You can also have your vehicle fittedwith:
• an airbag deactivation switch• an airbag deactivation warning
lamp.
23
Occupant protection
Driver and front passengerairbags
E74302
The driver and front passengerairbags will deploy during significantfrontal collisions or collisions that areup to 30 degrees from the left or theright. The airbags will inflate within afew thousandths of a second anddeflate on contact with theoccupants, thus cushioning forwardbody movement. During minor frontalcollisions, overturns, rear collisionsand side collisions, the driver andfront passenger airbags will notdeploy.
Side airbags
E72658
Side airbags are fitted inside theseatback of the front seats. A labelindicates that side airbags are fittedto your vehicle.
The side airbags will deploy duringsignificant lateral collisions. Only theairbag on the side affected by thecollision will deploy. The airbags willinflate within a few thousandths of asecond and deflate on contact withthe occupants, thus providingprotection for the chest and shoulderareas. During minor lateral collisions,overturns, front collisions and rearcollisions, the side airbags will notdeploy.
24
Occupant protection
Curtain airbags
E75004
Curtain airbags are fitted inside thetrim panels over the front and rearside windows. Moulded badges inthe B-pillar trim panels indicate thatcurtain airbags are fitted to yourvehicle.
The curtain airbags will deploy duringsignificant lateral collisions. Only theairbag on the side affected by thecollision will deploy. The airbag willinflate within a few thousandths of asecond and deflate on contact withthe occupants, thus providingprotection for the head. During minorlateral collisions, front collisions, rearcollisions, or overturns the curtainairbags will not deploy.
Seat belts
WARNINGSWear a seat belt and keepsufficient distance between
yourself and the steering wheel. Onlywhen you use the seat belt properly,can it hold you in a position toachieve its optimum effect. SeeSitting in the correct position(page 74).
Never use a seat belt for morethan one person.
Use the correct buckle for eachseat belt.
Do not use a seat belt that isslack or twisted.
Do not wear thick clothing. Theseat belt must fit tightly around
your body to achieve its optimumeffect.
Position the shoulder strap ofthe seat belt over the centre of
your shoulder and position the lapstrap tightly across your hips.
The driver and front passenger seatbelt retractors are fitted with a seatbelt pretensioner. Seat beltpretensioners have a lowerdeployment threshold than theairbags. During minor collisions, it ispossible that only the seat beltpretensioners will deploy.
25
Occupant protection
FASTENING THE SEATBELTS
WARNING
Insert the tongue into the buckleuntil you hear a distinct click.
You have not fastened the seat beltproperly if you do not hear a click.
E74124
E85817
Pull the belt out steadily. It may lockif you pull it sharply or if the vehicle ison a slope.
Press the red button on the buckleto release the belt. Let it retractcompletely and smoothly.
SEAT BELT HEIGHTADJUSTMENT
E87511
Note: Lifting the slider slightly whilepressing the locking button makes iteasier to release the lockingmechanism.
To raise or lower, press the lockingbutton on the adjuster and move asnecessary.
26
Occupant protection
USING SEAT BELTSDURING PREGNANCY
E68587
WARNING
Position the seat belt correctlyfor your safety and that of your
unborn child. Do not use only the lapstrap or the shoulder strap.
Position the lap strap comfortablyacross your hips and low beneathyour pregnant abdomen. Position theshoulder strap between your breasts,above and to the side of yourpregnant abdomen.
DISABLING THEPASSENGER AIRBAG
WARNING
Make sure that the passengerairbag is disabled when using a
rearward facing child restraint on thefront passenger seat.
E71313
Fitting the passengerairbag deactivation switch
WARNING
If you need to fit a child restrainton a seat protected by an
operational airbag in front of it, havea passenger airbag deactivationswitch fitted. Ask your dealer forfurther information.
Note: The key switch is located inthe glove compartment with anairbag deactivation lamp in theinstrument panel.
If the airbag warning lamp illuminatesor flashes when you are driving, thisindicates a malfunction. SeeWarning lamps and indicators(page 57). Remove the child restraintand have the system checkedimmediately.
27
Occupant protection
Disabling the passengerairbag
A BE71312
DisabledA
EnabledB
Turn the switch to position A.
When you switch the ignition on,check that the passenger airbagdeactivation warning lamp illuminates.
Enabling the passengerairbag
WARNING
Make sure that the passengerairbag is enabled when you are
not using a child restraint on the frontpassenger seat.
Turn the switch to position B.
28
Occupant protection
GENERAL INFORMATIONON RADIO FREQUENCIES
CAUTION
The radio frequency used byyour remote control can also be
used by other short distance radiotransmissions (e.g. amateur radios,medical equipment, wirelessheadphones, remote controls andalarm systems). If the frequencies arejammed, you will not be able to useyour remote control. You can lockand unlock the doors with the key.
Note: You could unlock the doors ifyou press the buttons on the remotecontrol unintentionally.
The operating range between yourremote control and your vehiclevaries depending on theenvironment.
PROGRAMMING THEREMOTE CONTROL
A maximum of four remote controls(including the ones supplied with thevehicle) can be programmed.
E72191
To programme a new remotecontrol:
• Turn the ignition key to position IIfour times within six seconds.
• Switch off the ignition. A tonesounds to indicate that it is nowpossible to programme a newremote control.
• Press any button on a newremote control. A tone will soundas confirmation. Repeat this laststep for all of your remotecontrols, including the original.
• Switch the ignition back on or waitfor ten seconds withoutprogramming another remotecontrol to end remote controlprogramming. Only the remotecontrols which you have justprogrammed are now able to lockand unlock your vehicle.
29
Keys and remote controls
Re-programming theunlocking function
You can change the unlockingfunction so that pressing the unlockbutton once deactivates the centrallocking or double locking, disarmsthe anti-theft alarm system andunlocks the driver’s door. Pressingthe unlock button twice within threeseconds also unlocks thepassengers’ doors.
If you want the tailgate to be lockedwhile driving, press the locking buttonon the driver’s door to activatecentral locking.
E72190
In order to re-programme thefunction, press and hold the unlockand lock buttons simultaneously forat least four seconds with the ignitionswitched off. The direction indicatorswill flash twice to indicate that theunlocking function has beensuccessfully re-programmed.
Pressing and holding both buttonssimultaneously for at least fourseconds again will change thefunction back.
CHANGING THE REMOTECONTROL BATTERY
If the range of the transmitter in thekey decreases gradually, the battery(type 3V CR 2032) should bereplaced.
E68726
• Carefully seperate the transmitterunit from the key using a flatobject (e.g. a screwdriver) at therecess on the back.
• Carefully prise out the battery withthe flat object. Fit the new batterybetween the contacts with the +sign facing downwards.Reassemble the transmitter unitin reverse order.
E68727
• Open the transmitter unit byseperating the retaining clips onthe sides with the flat object.
30
Keys and remote controls
E68729
• Carefully prise out the battery withthe flat object. Fit the new batterybetween the contacts with the +sign facing downwards.Reassemble the transmitter unitin reverse order.
31
Keys and remote controls
LOCKING ANDUNLOCKING
Central locking
You can only centrally lock the doorsif they are all closed.
Double locking
WARNINGSDo not activate double lockingwhen persons or animals are
inside the vehicle.
You will not be able to unlockthe doors from the inside if you
have double locked them.
Double locking is a theft protectionfeature that prevents someone fromopening the doors from the inside.You can only double lock the doorsif they are all closed.
Locking and unlockingconfirmation
When you unlock the doors, thedirection indicators will flash once.
When you lock the doors, thedirection indicators will flash twice.
Note: If your vehicle has doublelocking, the direction indicators willonly flash twice once you haveactivated double locking.
Locking and unlocking thedoors with the key
B
E71962
A
B
A
UnlockA
LockB
Double locking the doors withthe key
Turn the key to the unlock positionand then the lock position within twoseconds.
32
Locks
Locking and unlocking thedoors with the remotecontrol
E87379
A B C
UnlockA
LockB
Luggage compartment lidunlock
C
Locking the doors with theremote control
Press button B once.
Double locking the doors withthe remote control
Press button B twice within threeseconds.
Unlocking the luggagecompartment lid
Press button C twice within threeseconds.
Automatic relocking
The doors will relock automatically ifyou do not open a door within 45seconds of unlocking the doors withthe remote control. The door locksand the alarm will return to theirprevious state.
Reprogramming theunlocking function
You can reprogram the unlockingfunction so that only the driver's dooris unlocked or all doors are unlocked.Press the lock and unlock buttons onthe remote control at the same timefor four seconds with the ignitionswitched off. The direction indicatorswill flash twice as confirmation.
33
Locks
PRINCIPLE OFOPERATION
The engine immobiliser is a theftprotection system that preventssomeone from starting the enginewith an incorrectly coded key.
CODED KEYS
Note: Do not shield your keys withmetal objects. This may prevent thereceiver from recognising your keyas a valid one.
Note: Have all of your remainingkeys erased and recoded if you losea key. Ask your dealer for furtherinformation. Have replacement keysrecoded together with your existingkeys.
If you lose a key, you can obtain areplacement from your Ford Dealer.If possible, provide them with the keynumber from the tag provided withthe original keys. You can also obtainadditional keys from your FordDealer.
ARMING THE ENGINEIMMOBILISER
The engine immobiliser is armedautomatically a short time after youhave switched the ignition off.
The indicator in the instrument clusterwill flash to confirm that the systemis operating.
DISARMING THE ENGINEIMMOBILISER
Switching on the ignition disarms thesystem if the correct code isrecognised. The indicatorilluminates for approximately threeseconds and then extinguishes.
If the indicator illuminates constantlyfor one minute or flashes forapproximately one minute and thenrepeatedly at irregular intervals, thesystem did not recognise the keycode or a system fault is present.Remove the key and try again.
If the engine does not start, a systemmalfunction has occurred. Have thesystem checked by an expertimmediately.
34
Engine immobiliser
ARMING THE ALARM
The system is armed as soon as thevehicle is locked and acts as adeterrent to unauthorised personswho attempt to open the doors,bonnet or luggage compartment, orremove the audio system.
Automatic arming delay
The 20 seconds arming delay beginswhen the bonnet, luggagecompartment and all doors areclosed and locked.
Alarm
The alarm sounds for 30 seconds ifan unauthorised person opens adoor, the load compartment or thebonnet. The hazard warning flasherswill flash for five minutes.
Any attempt to start the engine or toremove the audio system sounds thealarm again.
DISARMING THE ALARM
Disarm and silence the alarm byunlocking either of the front doors orluggage compartment with the key.
35
Alarm
ADJUSTING THESTEERING WHEEL
E70358
WARNING
Never adjust the steering wheelwhen the vehicle is moving.
Release the locking lever to adjustthe height of the steering wheel andits distance from the driver.
Return the lever to its original positionto secure the wheel.
See Sitting in the correctposition (page 74).
AUDIO CONTROL
Select radio, CD or cassette modeon the audio unit.
The following functions can beoperated with the remote control:
Volume
E70361
Volume up: Pull the VOL+ switchtowards the steering wheel.
Volume down: Pull the VOL− switchtowards the steering wheel.
Seek
E70362
Move the SEEK switch towards thesteering wheel or the instrumentpanel:
• In radio mode, this will locatethe next radio station up or downthe frequency band.
• In CD mode, it will select thenext or previous track.
36
Steering wheel
Mode
E70363
Briefly press the button on the side:
• In radio mode, this will locatethe next pre-set radio station.
• In CD mode, this will select thenext CD if a CD changer is fitted.
• In all modes to abort a trafficmessage during broadcasting.
Press and hold the button on theside:
• In radio mode, to change thewaveband.
37
Steering wheel
WINDSCREEN WIPERS
A
B
C
D
E72172
Single wipeA
Intermittent wiping orautowipers
B
Normal wipingC
High speed wipingD
Intermittent wiping
E72173
2
Select wipe interval with rotaryswitch: 1 = Short time interval. 6 =Extended time interval.
Autowipers
WARNINGSIn icy conditions, make sure thatthe windscreen has been fully
defrosted before selectingautowipers.
Switch off the autowipersfeature before entering a car
wash.
Replace the wiper blades assoon as they begin to leave
bands of water and smears or whenthey do not completely remove waterfrom the windscreen. If the bladesare not replaced, the rain sensor willcontinue to detect water on thewindscreen. This will result in thewipers continuing to operatealthough the majority of thewindscreen is dry.
Note: The autowipers feature isintended for use during wet weatherconditions only and is very sensitiveto anything which touches thewindscreen near to the rain sensor.Objects such as dirt, mist or flieshitting the windscreen in this locationmay cause the wipers to wipe eventhough the windscreen is mostly dry.
Note: The autowipers feature shouldnot be selected when it is snowing,foggy or when the roads have beensalted. In these weather conditions,select an alternative position ifnecessary.
38
Wipers and washers
When autowipers is selected, thewipers will cycle once regardless ofwhether the windscreen is wet or dry.Thereafter, or when the ignition isswitched on with autowipersselected, the wipers will not cycleuntil water is detected on thewindscreen. Alternatively, move thelever to another position and thenselect autowipers, or operate thewasher.
The rain sensor will continuouslymeasure the amount of water on thewindscreen and adjust the speed ofthe front wipers automatically (singlewipe, intermittent, normal or highspeed wiping).
E72173
2
The sensitivity of the rain sensor isset using the rotary control:
1 = High sensitivity: The wipers willwipe even if only a small amount ofwater is detected on the windscreen.
6 = Low sensitivity: The wipers willonly wipe when a larger amount ofwater is detected on the windscreen.
WINDSCREEN WASHERS
E72174
WARNING
Do not operate the windscreenwasher for more than 10
seconds or when the reservoir isempty.
REAR WINDOW WIPERAND WASHERS
Intermittent wiping
E72175
Pull the lever towards the steeringwheel.
Reverse gear wipe
The rear wiper will be activatedautomatically when selecting reversegear, if
39
Wipers and washers
• the rear wiper is not alreadyswitched on,
• the wiper lever is in position C, orD
• in position B and the front wipersare operating.
The rear wiper will follow the frontwiper interval (at intermittent ornormal speed).
Washer
E72176
WARNING
Do not operate the washer formore than 10 seconds at a time,
and never when the reservoir isempty.
Pull the lever fully towards thesteering wheel and hold it to operatethe washer.
The washer will operate inconjunction with the wipers.
The washer jet for the rear windowis located on the roof above the rearwindow.
ADJUSTING THEWINDSCREEN WASHERJETS
E73425
The eye ball jets can be adjustedprecisely using a pin.
CHECKING THE WIPERBLADES
E66644
Run the tip of your fingers over theedge of the blade to check forroughness.
Clean the wiper blade lips with waterapplied with a soft sponge.
40
Wipers and washers
CHANGING THE WIPERBLADES
E66645
5
2
43
1
Lift the wiper arm and position thewiper blade at a right angle to thewiper arm. To remove, press theretaining clip in the direction of thearrow, disengage the wiper bladeand pull it off the arm in the oppositedirection.
41
Wipers and washers
LIGHTING CONTROL
Lighting control positions
AB
C
E72161
OffA
Side and tail lampsB
HeadlampsC
Autolamps
E72162
Note: If you have switchedautolamps on, you can only switchthe main beam on when autolampshas switched the headlamps on.
The headlamps will come on and gooff automatically depending on theambient light.
Home safe lighting
You can switch home safe lighting onup to 10 minutes after you haveswitched the ignition off.
Vehicles without autolamps
Switch the headlamps on and thenswitch them off within two seconds.
Vehicles with autolamps
a. Switch autolamps on and thenswitch them off within twoseconds.
b. Switch autolamps off and thenswitch them on within twoseconds.
Welcome lighting
The side and tail lamps will come onwhen you unlock the doors with theremote control. They will switch offautomatically after a short time.
42
Lighting
Main/dipped beam
E72168
Pull the lever fully towards thesteering wheel to switch betweenmain and dipped beam.
Headlamp flasher
E72168
Pull the lever slightly towards thesteering wheel.
FRONT FOG LAMPS
E72163
Note: It is not possible to switch onthe front fog lamps when the lightingswitch is set to AUTO. To switch onthe front fog lamps, switch off theautolamps feature.
Switch on the headlamps 1 and pullout the control switch one position2.
The front fog lamps should be usedonly when visibility is considerablyrestricted by fog, snow or rain.
43
Lighting
REAR FOG LAMPS
1
2E72164
WARNING
The rear fog lamps may only beused when visibility is restricted
to less than 50 m and must not beused when it is raining or snowing.
Note: On vehicles not equipped withfront fog lamps the control switchcan be pulled out only one position.
Note: It is not possible to switch onthe rear fog lamps when the lightingswitch is set to AUTO. To switch onthe rear fog lamps, switch off theautolamps feature.
Switch on the exterior lamps 1 andpull out the control two positions 2.
HEADLAMP LEVELLING
E65990
You can adjust the level of theheadlamp beams according to thevehicle load.
Recommended headlamp levelling switch positions
Switch positionLoad in luggagecompartment
Load
Second rowseats
Front seats
0--1-2
1-31-2
1.5Max131-2
2Max1-1
1 See Weights (page 167).
44
Lighting
HAZARD WARNINGFLASHERS
Note: Depending on applicable lawsand regulations in the country forwhich your vehicle was originally built,the hazard warning flashers may flashif you brake heavily.
E71943
For item location: See Quick start(page 8).
DIRECTION INDICATORS
E72167
Briefly tap the lever up or down andthe direction indicators will flash threetimes.
INTERIOR LAMPS
Courtesy lamp
CBA
E71945
OffA
Door contactB
OnC
E91006
A B C
A B C
OffA
Door contactB
OnC
45
Lighting
If you set the switch to position B, thecourtesy lamp will come on when youunlock or open a door or the tailgate.If you leave a door open with theignition switch off, the courtesy lampwill go off automatically after sometime to prevent the vehicle batteryfrom discharging. To switch it backon, switch on the ignition for a shorttime.
The courtesy lamp will also come onwhen you switch off the ignition. It willgo off automatically after a short timeor when you start or restart theengine.
If you set the switch to position Cwith the ignition switch off, thecourtesy lamp will come on. It will gooff automatically after a short time toprevent the vehicle battery fromdischarging. To switch it back on,switch on the ignition for a short time.
Reading lamps
E71946
A
B
E72900
OffA
OnB
REMOVING A HEADLAMP
1. Open the bonnet. See Openingand closing the bonnet (page112).
E90592
4
51
2
3
2. Remove the screws.
46
Lighting
3
E90593
CAUTION
Do not pull the bumper morethan 10 mm from its original
position.
3. Carefully pull the bumper towardsthe front of the vehicle andremove the screw.
4. Disconnect the electricalconnector and remove theheadlamp.
CAUTION
When fitting the headlamp, takecare not to damage the locating
points.
Note: When fitting the headlamp,make sure that you fully engage theheadlamp in the fixing points.
CHANGING A BULB
WARNINGSSwitch the lights and the ignitionoff.
Let the bulb cool down beforeremoving it.
CAUTIONSDo not touch the glass of thebulb.
Only fit bulbs of the correctspecification. See Bulb
specification chart (page 52).
Note: The following instructionsdescribe how to remove the bulbs.Fit replacement in the reverse orderunless otherwise stated.
Headlamp main and dippedbeam
1. Remove the headlamp. SeeRemoving a headlamp (page46).
E91017
47
Lighting
2. Remove the cover.
3. Disconnect the electricalconnector.
4. Release the clip and remove thebulb.
Side lamps
1. Remove the headlamp. SeeRemoving a headlamp (page46).
E91018
2. Remove the cover.
3. Carefully prise out the bulb holder.
4. Remove the bulb.
Front direction indicators
1. Remove the headlamp. SeeRemoving a headlamp (page46).
E91016
2. Turn the bulb holder anticlockwiseand remove it.
3. Gently press the bulb into the bulbholder, turn it anticlockwise andremove it.
Side repeaters
2
13
E78869
1. Carefully remove the siderepeater.
2. Hold the bulb holder, turn thehousing anticlockwise andremove it.
3. Remove the bulb.
48
Lighting
Front fog lamps
E91019
1. Disconnect the electricalconnector.
2. Turn the bulb holder anticlockwiseand remove it.
Rear lamps
1. Open the tailgate.
E91020
2. From inside the luggagecompartment, remove the wingnut on the back of the rear lamp.
3. Remove the screws and removethe rear lamp assembly.
4. Release the clips and remove thebulb holder.
A
B
CD
E91021
5. Gently press the bulbs into thebulb holder, turn themanticlockwise and remove them.
49
Lighting
Central high mounted stoplamp
2 3
4
E90600
1. Open the tailgate.
2. Remove the rubber grommet.
3. Release the clips using aflat-bladed screwdriver andremove the lamp.
4. Unclip the bulb holder and removethe bulb.
Number plate lamp
E90601
1. Loosen the screws and removethe lamp.
2. Remove the bulb.
Interior lamp
E73091
1
2
50
Lighting
E73092
3
1. Carefully prise out the lamp.
2. Remove the lens.
3. Remove the bulb.
Reading lamps
E73938
1
2
E73939
3
1. Carefully prise out the lamp.
2. Turn the bulb holder anticlockwiseand remove it.
3. Remove the bulb.
Luggage compartmentlamp
E72784
1. Carefully prise out the lamp.
2. Remove the bulb.
51
Lighting
BULB SPECIFICATION CHART
Rating (watt)SpecificationBulb
21PY21WFront direction indicator
5Side lamp
55/60H4Headlamp
5Side repeater
55H11Front fog lamp
5P21/5WBrake and tail lamp
21P21WRear direction indicator
21P21WReversing lamp
21P21WRear fog lamp
16Central high mountedstop lamp
5ZW5Number plate lamp
10Interior lamp
5Reading lamp
5Luggage compartmentlamp
52
Lighting
ELECTRIC WINDOWS
WARNING
Do not operate the electricwindows unless they are free
from obstruction.
Note: If you operate the switchesoften during a short period of time,the system might become inoperablefor a certain time to prevent damagedue to overheating.
E93505
Switch on the ignition to operate theelectric windows.
To open the driver’swindow automatically
Press the switch to the second actionpoint and release it. Press it again tostop the window.
EXTERIOR MIRRORS
Convex mirrors
E71042
WARNING
Do not overestimate thedistance of the objects that you
see in the convex mirror. Objectsseen in convex mirrors will appearsmaller and further away than theyactually are.
Folding mirrors
E71043
Make sure that you fully engage themirror in its support when returningit to its original position.
53
Windows and mirrors
ELECTRIC EXTERIORMIRRORS
E66485
A
B
C
Left-hand mirrorA
OffB
Right-hand mirrorC
Electric exterior mirrors are fitted witha heating element that will defrost ordemist the mirror glass. They willswitch on automatically when youswitch the heated rear window on.
Mirror tilting positions
E66486
A
B
C
D
upA
rightB
downC
leftD
Electric folding mirrors
E72184
Automatic folding
The mirrors will fold automaticallywhen you lock the vehicle with theremote control. The mirrors will unfoldwhen you unlock the vehicle with thekey or the remote control.
54
Windows and mirrors
INTERIOR MIRROR
E71272
Dip the mirror to reduce glare whendriving at night.
55
Windows and mirrors
GAUGES
E89015
BA C D
TachometerA
Engine coolant temperature gaugeB
Fuel gaugeC
SpeedometerD
Information displayE
Engine coolant temperaturegauge
All vehicles
Shows the temperature of the enginecoolant. At normal operatingtemperature, the needle will remainin the centre section.
CAUTION
Do not restart the engine until thecause of overheating has been
resolved.
56
Instruments
If the needle enters the red section,the engine is overheating. Stop theengine, switch the ignition off anddetermine the cause once theengine has cooled down.
Vehicles with an informationdisplay
In addition, a warning message willappear in the display.
Fuel gauge
The arrow adjacent to the fuel pumpsymbol tells you on which side ofyour vehicle the fuel filler cap islocated.
WARNING LAMPS ANDINDICATORS
The following warning lamps andindicators will come on briefly whenyou switch the ignition on to confirmthat the system is operational:• ABS warning lamp• Airbag warning lamp• Brake system warning lamp• Door open warning lamp• Engine warning lamp• Frost warning lamp• Ignition warning lamp• Oil pressure warning lamp• Power steering warning lamp• Powertrain warning lamp.• Stability control (ESP) warning
lamp
If a warning lamp or indicator doesnot come on when you switch theignition on, this indicates amalfunction. Have the systemchecked as soon as possible.
ABS warning lamp
The ABS warning lamp willflash when the system isoperating. If it comes on
when you are driving, this indicatesa malfunction. You will continue tohave normal braking (without ABS)but have this checked as soon aspossible.
Airbag warning lamp
If the airbag warning lampcomes on or flashes whenyou are driving, this indicates
a malfunction. Have this checked assoon as possible.
Brake system warning lamp
WARNING
Reduce your speed gradually.Use your brakes with great care.
Do not step on the brake pedalabruptly.
The brake system warninglamp will stay on until yourelease the parking brake. If
it comes on when you are driving, thisindicates a malfunction in one of thebrake circuits. Check the brake fluidlevel. See Maintenance (page 111).
57
Instruments
WARNING
Have this checked immediately.
If the brake system warning lampcomes on with the ABS warning lampor the stability control warning lamp,this indicates a malfunction. Stop yourvehicle as soon as it is safe to do soand have this checked beforecontinuing you journey.
Direction indicator
The direction indicator willflash when you use thedirection indicators. A
sudden increase in the rate offlashing warns of a failed bulb.
Door open warning lamp
The door open warninglamp will come on if a door,the tailgate or the bonnet is
open.
Engine warning lamp
If the engine warning lampcomes on when the engineis running, this indicates a
malfunction. If it flashes when you aredriving, reduce the speed of yourvehicle immediately. If it continues toflash, avoid heavy acceleration ordeceleration. The engine will continueto run but it will have limited power.Have this checked immediately.
Front fog lamp indicator
The front fog lamp indicatorwill come on when youswitch the front fog lamps
on.
Frost warning lamp
The frost warning lamp willcome on and glow orangewhen the outside air
temperature is between 4ºC and 1ºC.It will glow red when the temperatureis below 1ºC.
Glow plug indicator
See Starting a dieselengine (page 84).
Headlamp indicator
The headlamp indicator willcome on when you switchthe headlamp dipped beam
or the side and tail lamps on.
Ignition warning lamp
If the ignition warning lampcomes on when you aredriving, this indicates a
malfunction. Switch off allunnecessary electrical equipmentand have this checked immediately.
Low fuel level warning lamp
If the low fuel level warninglamp comes on, refuel assoon as possible.
58
Instruments
Main beam indicator
The main beam indicator willcome on when you switchthe headlamp main beam
on. It will flash when you use theheadlamp flasher.
Oil pressure warning lamp
CAUTION
Do not resume your journey if theoil pressure warning lamp comes
on despite the oil level being correct.Have this checked immediately.
If the oil pressure warninglamp comes on when youare driving, this indicates a
malfunction. Stop your vehicle assoon as it is safe to do so and switchthe engine off. Check the engine oillevel. See Maintenance (page 111).
Overdrive indicator
The overdrive indicator willcome on when you switchoverdrive off.
Power steering warninglamp
If the power steeringwarning lamp comes onwhen you are driving, this
indicates a malfunction. You willcontinue to have normal steering(without assistance) but have thischecked as soon as possible. Youwill have to use greater force to turnthe steering wheel.
Powertrain warning lamp
Vehicles with an automatictransmission
If the powertrain warninglamp comes on when theengine is running, this
indicates either a malfunction or ahigh transmission temperature. Stopyour vehicle as soon as it is safe todo so and carry out the following:
1. Select P or N and allow theengine to idle for 10 minutes.
2. Switch the ignition off and restartthe engine.
If the powertrain warning lampcomes on, switch the ignition off andhave the transmission checkedbefore continuing your journey.
If the powertrain warning lamp doesnot come on, continue your journeyand have the transmission checkedas soon as possible.
Vehicles with a 5-speedmanual transmission orDurashift EST
If the powertrain warninglamp comes on when theengine is running, this
indicates a malfunction. The enginewill continue to run but it will havelimited power. Have this checked assoon as possible.
59
Instruments
If the powertrain warning lampflashes when the engine is running,this indicates a malfunction. Stop yourvehicle as soon as it is safe to do so.Have this checked before continuingyour journey.
Rear fog lamp indicator
The rear fog lamp indicatorwill come on when youswitch the rear fog lamps
on.
Stability control (ESP)warning lamp
Note: If the ESP systemmalfunctions, it will switch offautomatically.
The ESP warning lamp willflash when system isoperating. If it does not flash
or it comes on when you are driving,this indicates a malfunction. Have thischecked as soon as possible.
If you switch ESP off, the warninglamp will come on. The lamp will goout when you switch the systemback on or when you switch theignition off.
60
Instruments
GENERAL INFORMATION
WARNING
Do not operate the informationdisplay controls when the
vehicle is moving.
Note: The information display willremain on for several minutes afteryou switch off the ignition.
Note: If Sh on or SHIP ON isdisplayed, the vehicle shipping modeis switched on. Have your dealerswitch off the vehicle shipping mode.
Type 1 information display
E91003
E D
A
BC
Distance to empty or clockA
TripmeterB
OdometerC
Select buttonD
Reset buttonE
Press the select button to scrollthrough the displays.
Setting the time
E91004
Note: You can only set the timethrough the audio unit on somevehicles. See separate handbook.
1. Press the select button until thetime flashes in the display.
2. Press the select button to set thetime.
61
Information displays
Type 2 information display
A
F
BC
E
E91005
D
Selected gearA
Clock, radio station or CDtrack
B
Outside air temperatureC
TripmeterD
OdometerE
Message indicatorF
You can change the settings ofvarious functions through theinformation display. The informationdisplay also provides informationmessages.
E70436
Press the button to scroll through thedisplays and hold the button to rest,select a submenu or change asetting. The information display willtell you whether a short press of thebutton or long press of the button isrequired for the various options.
Message indicator
The message indicator will come onto supplement some messages. Itwill be red or amber depending onthe severity of the message and willremain on until the cause of themessage has been rectified.
Display definitions
Distance to empty
Indicates the approximate distancethat your vehicle will travel on the fuelin the fuel tank.
Average speed
Indicates the average speed of yourvehicle since the last reset.
Average fuel
Indicates the average fuelconsumption of your vehicle sincethe last reset.
Fuel economy
Indicates the current fuelconsumption of your vehicle.
62
Information displays
PERSONALISEDSETTINGS
You can change the settings ofvarious functions through theinformation display.
Unlocking the doors withthe remote control
You can set the unlocking functionto unlock the driver side front dooronly or to unlock all of the doors.
Direction indicators
You can set the direction indicatorsto flash only three times when youtap the direction indicator level.
Audio display
You can set the information displayto display certain audio unitinformation.
Hazard warning flashers
You can set the hazard warningflashers to flash automatically whenyou brake heavily.
Audible warnings
You can switch off some of theaudible warnings.
Language
You can set the display to yourpreferred language.
INFORMATIONMESSAGES
E70436
Press the button to acknowledgeand remove some messages fromthe information display. Othermessages will be removedautomatically after a short time.Messages will remain active until thecause has been rectified.
63
Information displays
MeaningMessage indic-ator
Message
This indicates a malfunction in one ofthe brake circuits. Check the brakefluid level. See Maintenance (page111). If the ABS warning lamp or thestability control warning lamp alsocome on, this indicates a malfunction.Stop your vehicle as soon as it is safeto do so and have this checkedbefore continuing you journey.
RedLOW BRAKEFLUID LEVEL
The engine is overheating. Stop theengine, switch the ignition off anddetermine the cause once theengine has cooled down.
RedHIGH ENGINETEMPERATURE
The transmission system hasmalfunctioned. Vehicles with anautomatic transmission: Stopyour vehicle as soon as it is safe to doso. Select P or N and let the engineidle for 10 minutes. Switch the ignition
RedTRANSMISSIONMALFUNCTION
off and then restart the engine. If themessage is still displayed, switch theignition off and have this checkedbefore continuing your journey. If themessage is no longer displayed, youcan continue your journey and havethis checked as soon as possible.Vehicles with a Durashift ESTtransmission: Stop your vehicle assoon as it is safe to do so. Switch theignition off and have this checkedbefore continuing your journey.
64
Information displays
MeaningMessage indic-ator
Message
The transmission system hasmalfunctioned. Avoid heavy accelera-tion or deceleration. The transmissionwill continue to operate but you willnotice some unusual conditions. Havethis checked as soon as possible.
AmberTRANSMISSIONMALFUNCTION
The power steering system hasmalfunctioned. You will need to usegreater force to turn the steeringwheel. Have this checked as soon aspossible.
RedSTEERING ASSISTFAILURE
The engine system has malfunc-tioned. Stop your vehicle as soon asit is safe to do so. Switch the ignitionoff and have this checked beforecontinuing your journey.
RedENGINE SYSTEMFAULT
The engine system has malfunc-tioned. Avoid heavy acceleration ordeceleration. The engine will continueto run but it will have limited power.Have this checked as soon aspossible.
AmberENGINE SYSTEMFAULT
The outside air temperature is below1ºC.
RedLOW OUTSIDETEMPERATURE
The outside air temperature isbetween 4ºC and 1ºC.
AmberLOW OUTSIDETEMPERATURE
Vehicles with an automatictransmission: The transmission isoverheating. Stop your vehicle assoon as it is safe to do so. Select P orN and let the engine idle for 10minutes. Switch the ignition off and
AmberTRANSMISSIONHOT MODE
then restart the engine. If the
65
Information displays
MeaningMessage indic-ator
Message
message is still displayed, switch theignition off and have this checkedbefore continuing your journey. If themessage is no longer displayed, youcan continue your journey and havethis checked as soon as possible.
A left-hand side indicator bulb hasfailed.
AmberLEFT INDICATORBULB FAILURE
A right-hand side indicator bulb hasfailed.
AmberRIGHT INDIC-ATOR BULBFAILURE
The driver side front door is open.AmberDRIVER DOOROPEN
The driver side rear door is open.AmberDRIVER SIDEREAR DOOROPEN
The passenger side front door isopen.
AmberPASSENGERDOOR OPEN
The passenger side rear door is open.AmberPASSENGER SIDEREAR DOOROPEN
The tailgate is open.AmberBOOT OPEN
The bonnet is open.AmberBONNET OPEN
The remote control battery is low.Have this checked as soon aspossible.
AmberREMOTE KEYBATTERY LOW
Autolamps or autowipers havemalfunctioned. Have this checked assoon as possible.
FAILURE AUTOLAMP/WIPER
66
Information displays
PRINCIPLE OFOPERATION
Outside air
Keep the air intakes forward of thewindscreen free from obstruction(snow, leaves etc.) to allow theclimate control system to functioneffectively.
Recirculated air
CAUTION
Prolonged use of recirculated airmay cause the windows to mist
up. If the windows mist up, follow thesettings for defrosting and demistingthe windscreen.
The air currently in the passengercompartment will be recirculated.Outside air will not enter the vehicle.
Heating
Heating performance depends onthe temperature of the enginecoolant.
Air conditioning
Note: The air conditioning operatesonly when the temperature is above4ºC (39ºF).
Note: If you use the air conditioning,the fuel consumption of your vehiclewill be higher.
Air is directed through the evaporatorwhere it is cooled. Humidity isextracted from the air to help keepthe windows free of mist. Theresulting condensation is directed tothe outside of the vehicle and it istherefore normal if you see a smallpool of water under your vehicle.
General information oncontrolling the interiorclimate
Fully close all the windows.
Warming the interior
Direct the air towards your feet. Incold or humid weather conditions,direct some of the air towards thewindscreen and the door windows.
Cooling the interior
Direct the air towards your face.
AIR VENTS
E71942
67
Climate control
MANUAL CLIMATECONTROL
Blower
E90444
OffA
Note: If you switch the blower off,the windscreen may mist up.
Temperature control
E90445
ColdBlue
WarmRed
Air distribution control
E90446
WindscreenA
Footwell and windscreenB
Face levelC
68
Climate control
Face level and footwellD
FootwellE
Face level, windscreen andfootwell
F
You can set the air distribution controlto any position between the symbols.
A small amount of air is alwaysdirected towards the windscreen.
Defrosting and demistingthe windscreen
E90447
If necessary, switch the heatedwindows on. See Heatedwindows and mirrors (page 72).
Ventilation
E90448
Heating the interior quickly
E90449
Switching the airconditioning on and off
If you turn the blower off, the airconditioning will turn off. When youturn the blower on again, the airconditioning will come onautomatically.
Recirculated air
Cooling with outside air
E90450
69
Climate control
Cooling the interior quickly
E90451
Reducing interior airhumidity
E90452
AUTOMATIC CLIMATECONTROL
E72153
The system controls thetemperature, amount and distributionof the air flow automatically andadjusts them according to the drivingand weather conditions. Pressing theAUTO button once switches on theauto mode.
Note: Avoid adjusting the settingswhen the vehicle interior is extremelyhot or cold. The automatic climatecontrol adjusts to the currentcircumstances automatically. For thesystem to function properly, the sideand centre vents should be fullyopen.
Note: The sunload sensor is locatedon top of the instrument panel. Donot cover the sensor with anyobjects.
Note: At low outside temperatures,when the system is in auto mode, theair stream will be directed to thewindscreen and the side windows aslong as the engine is cold.
Setting the temperature
E72154
Reduces temperatureBlue
Increases temperatureRed
70
Climate control
You can set the temperaturebetween 16ºC and 28ºC in steps of0.5ºC. In position LO (below 16ºC) thesystem will switch to permanentcooling, in HI (above 28ºC) topermanent heating, and not regulatea stable temperature.
Blower
Use the buttons to adjustthe blower speed. Theblower setting is indicated
in the display. To return to automode, press the AUTO button.
Air distribution
E70308
A B C
FootwellA
Face levelB
WindscreenC
Note: When you select windscreendefrosting and demisting, A, B andC switch off automatically and the airconditioning switches on. Outside airwill flow into the vehicle. You cannotselect recirculated air.
Windscreen defrosting anddemisting
Press the windscreendefrosting and demistingbutton. Outside air will flow
into the vehicle. Air conditioning isautomatically selected. As long as theair distribution is set to this position,you cannot select recirculated air.
The blower speed and thetemperature control operateautomatically and cannot be adjustedmanually. The blower is set to highspeed and the temperature to HI.
When you select windscreendefrosting and demisting, the heatedscreens switch on automatically andswitch off after a short time.
Press the windscreen defrosting anddemisting button again to return tothe previous settings.
Switching the airconditioning on and off
Press the A/C button toturn the air conditioning onand off.
Recirculated air
Press the recirculated airbutton to toggle betweenoutside air and recirculated
air.
71
Climate control
Note: When the system is in automode and the interior and exteriortemperatures are quite hot, thesystem selects recirculated airautomatically to maximise cooling ofthe interior. Once the selectedtemperature is reached, the systemwill reselect outside air automatically.
Switching the automaticclimate control on and off
E72157
Press the OFF button.
When switched off, the heating,ventilation and air conditioningsystem is switched off andrecirculated air is selected.
HEATED WINDOWS ANDMIRRORS
Heated windows
Use the heated windows to defrostor demist the windscreen or rearwindow.
Note: The heated windows operateonly when the engine is running.
Heated windscreen
E72506
Heated rear window
E72507
Heated exterior mirrors
Electric exterior mirrors are fitted witha heating element that will defrost ordemist the mirror glass. They willswitch on automatically when youswitch the heated rear window on.
AUXILIARY HEATER
Diesel auxiliary heater(depending on country)
The diesel auxiliary heater (PTCelectrical heater) aids in warming theengine and the interior compartmenton vehicles with diesel engines. It isswitched on or off automaticallydepending on the outsidetemperature, the coolanttemperature and the alternator load.
72
Climate control
SUNROOF
E90558
E72189
73
Climate control
SITTING IN THECORRECT POSITION
E68595
WARNINGSDo not adjust the seats whenthe vehicle is moving.
Only when you use the seat beltproperly, can it hold you in a
position that allows the airbag toachieve its optimum effect.
When you use them properly, theseat, head restraint, seat belt andairbags will provide optimumprotection in the event of a collision.We recommend that you:
• sit in an upright position with thebase of your spine as far back aspossible.
• do not recline the seatback morethan 30 degrees.
• adjust the head restraint so thatthe top of it is level with the top ofyour head and as far forwards aspossible, remaining comfortable.
• keep sufficient distance betweenyourself and the steering wheel.We recommend a minimum of254 millimetres (10 inches)between your breastbone and theairbag cover.
• hold the steering wheel with yourarms slightly bent.
• bend your legs slightly so that youcan press the pedals fully.
• position the shoulder strap of theseat belt over the centre of yourshoulder and position the lap straptightly across your hips.
Make sure that your driving positionis comfortable and that you canmaintain full control of your vehicle.
MANUAL SEATS
Moving the seatsbackwards and forwards
1
22
E74816
74
Seats
WARNING
Rock the seat backwards andforwards after releasing the
lever to make sure that it is fullyengaged in its catch.
Adjusting the height of thedriver’s seat
E68895
Adjusting the angle of theseatback
E74819
Folding the passenger seatforwards
WARNINGSDo not drive with the passengerseat folded forwards if the rear
seat directly behind it is occupied.
Do not drive with items on thefolded seatback.
E68896
1. Fold the seat forwards.
E91008
2. Turn the wheel until the seatbackis horizontal.
75
Seats
Pull the locking lever to return theseatback to the vertical position.Make sure that the seatback issecurely latched in position.
REAR SEATS
WARNINGSMake sure that the seats andthe seatbacks are secure and
fully engaged in their catches.
When folding the seatbacksdown, take care not to get your
fingers caught between the seatbackand seat frame.
CAUTION
Lower the head restraints.
Folding the seatbacksdown
1
2
1
E86611
1. Pull the unlock levers.
2. Push the seatback forwards.
Creating a level load floor
E91009
1 2 3
1. Lift the seat cusion.
2. Pull the locking lever and push theseatback forwards.
3. Press the rear of the seatbackdownwards.
HEAD RESTRAINTS
E75767
76
Seats
E81584
Adjusting the head restraint
WARNING
Raise rear head restraint whenthe rear seat is occupied by a
passenger or a child restraint.
Adjust the head restraint so that thetop of it is level with the top of yourhead.
Removing the headrestraint
Press the locking buttons andremove the head restraint.
HEATED SEATS
Driver side
E90906
Passenger side
E90907
CAUTION
Operating the heated seats withthe engine off will drain the
battery.
The heated seats will operate whenthe ignition switch is in position II.
77
Seats
FRONT SEAT ARMREST
Adjusting the armrest
E91007
1
2
3
1. Lift the armrest past the verticalposition.
2. Push the armrest fullydownwards.
3. Slowly lift the armrest to thedesired height.
78
Seats
SUN VISORS
E72973
CIGAR LIGHTER
E78055
WARNING
Never hold the lighter in as thiswill result in damage. Always
remove the lighter as a precautionwhen children are left alone in thevehicle.
To use the lighter, press it in and waituntil it pops out automatically. Thelighter will also operate when theignition is switched off.
Other appliances can be connectedto the cigar lighter power point.
When connecting appliances, useonly specified connectors from theFord Accessory range or connectorsfor use with SAE standard sockets.
GLOVE BOX
E91002C
BB
A
Card holderA
Coin holdersB
Pen or pencil clipC
STORAGECOMPARTMENTS
Storage box
A storage box is located under thepassenger seat cushion.
79
Convenience features
E91010
2
1
3
Storage pockets
E91011
A
B
Driver seatA
Rear seatB
80
Convenience features
REAR SEAT ARMREST
Activity console
Installing the activity console
E91012
1. Remove the centre seat cusion.
E91013
2. Install the activity console.
Removing the activity console
E91014
1. Pull the handle and remove theactivity console.
E91015
2. Install the centre seat cushion.
81
Convenience features
GENERAL INFORMATION
General points on starting
If the battery has been disconnectedthe vehicle may exhibit some unusualdriving characteristics for approx. 8kilometres (5 miles) afterreconnecting the battery.
This is because the enginemanagement system must realignitself with the engine. Any unusualdriving characteristics during thisperiod may be disregarded.
Starting the engine bytowing or pushing
WARNING
To prevent damage you mustnot push or tow start your
vehicle. Use booster cables and abooster battery. See Usingbooster cables (page 127).
IGNITION SWITCH
Ignition switch positions
Position 0
WARNING
Never return the key to the 0position when the vehicle is in
motion.
Ignition off. When the key is removedfrom the ignition switch, the steeringcolumn lock will be activated as soonas the steering wheel is turned.
Position I
Steering unlocked. Ignition and allmain electrical circuits are disabled.The ignition key should not be left inthis position for too long to avoiddischarging the battery.
Positon II
Ignition switched on, all electricalcircuits operational. Warning andindicator lamps illuminate. This is thekey position when driving, and mustalso be selected when being towed.
Postion III
Starter motor activated. Release thekey as soon as the engine starts.
STARTING A PETROLENGINE
Note: You can only operate thestarter for a maximum of 30 secondsat a time.
Cold or hot engine
All vehicles
CAUTION
When the temperature is below-20ºC (-4ºF), switch the ignition
on for at least one second beforestarting the engine. This will makesure that the maximum fuel pressureis established for starting the engine.
82
Starting the engine
Vehicles with manualtransmission
Note: Do not touch the acceleratorpedal.
1. Fully depress the clutch pedal.
2. Start the engine.
Vehicles with automatictransmission
Note: Do not touch the acceleratorpedal.
1. Select park or neutral.
2. Fully depress the brake pedal.
3. Start the engine.
All vehicles
If the engine does not start within 15seconds, wait for a short period andtry again.
If the engine does not start afterthree attempts, wait 10 seconds andfollow the Flooded engineprocedure.
If you have difficulty starting theengine when the temperature isbelow -25ºC (-13ºF), press theaccelerator pedal between ¼ to ½of its travel and try again.
Flooded engine
Vehicles with manualtransmission
1. Fully depress the clutch pedal.
2. Fully depress the acceleratorpedal and hold it there.
3. Start the engine.
Vehicles with automatictransmission
1. Select park or neutral.
2. Fully depress the acceleratorpedal and hold it there.
3. Fully depress the brake pedal.
4. Start the engine.
All vehicles
If the engine does not start, repeatthe Cold or hot engineprocedure.
Engine idle speed afterstarting
The speed at which the engine idlesimmediately after starting will varydepending on the enginetemperature.
If the engine is cold then the idlespeed will automatically be increased.
The idle speed will slowly decreaseto the normal level as the enginewarms up.
83
Starting the engine
STARTING A DIESELENGINE
Cold or hot engine
All vehicles
Note: When the temperature isbelow -15ºC (5ºF), you may need tocrank the engine for up to 25seconds. If you consistently operatethe vehicle in such temperatures, werecommend that you have an engineblock heater fitted.
Note: Continue cranking the engineuntil it starts.
Note: You can only operate thestarter for a maximum of 30 secondsat a time.
Switch the ignition on andwait until the glow plugindicator goes off.
Vehicles with manualtransmission
Note: Do not touch the acceleratorpedal.
1. Fully depress the clutch pedal.
2. Start the engine.
Vehicles with automatictransmission
1. Select park or neutral.
2. Fully depress the brake pedal.
3. Start the engine.
SWITCHING OFF THEENGINE
Vehicles with aturbocharger
CAUTION
Do not switch the engine offwhen it is running at high speed.
If you do, the turbocharger willcontinue running after the engine oilpressure has dropped to zero. Thiswill lead to premature turbochargerbearing wear.
Release the accelerator pedal. Waituntil the engine has reached idlespeed and then switch it off.
84
Starting the engine
SAFETY PRECAUTIONS
WARNINGSStop refuelling after the fuelnozzle stops the second time.
Additional fuel will fill the expansionspace in the fuel tank which couldlead to fuel overflowing. Fuel spillagecould be hazardous to other roadusers.
Do not use any kind of flamesor heat near the fuel system.
The fuel system is under pressure.There is a risk of injury if the fuelsystem is leaking.
FUEL QUALITY - PETROL
Note: We recommend that you useonly high quality fuel without additivesor other engine treatments.
CAUTION
Do not use leaded petrol orpetrol with additives containing
other metallic compounds (e.g.manganese-based). They coulddamage the emission system.
Use minimum 95 octaneunleaded petrol that meets thespecification defined by EN 228, orequivalent.
FUEL QUALITY - DIESEL
Note: We recommend that you useonly high quality fuel without additivesor other engine treatments.
WARNING
Do not mix diesel with oil, petrolor other liquids. This could cause
a chemical reaction.
CAUTION
Do not add kerosene, paraffin orpetrol to diesel. This could cause
damage to the fuel system.
Note: We do not recommend theprolonged use of additives intendedto prevent fuel waxing.
Use diesel that meets thespecification defined by EN 590, orequivalent.
You can use diesel that contains upto 5% RME (bio diesel).
CATALYTIC CONVERTER
Driving with a catalyticconverter
CAUTIONSAvoid running out of fuel.
Do not crank the engine for longperiods.
Do not run the engine when aspark plug lead is disconnected.
Do not push-start or tow-startyour vehicle. Use booster cables.
See Using booster cables (page127).
Do not switch the ignition offwhen driving.
85
Fuel and refuelling
Parking
WARNING
Do not park your vehicle overdry leaves or dry grass. The
exhaust will continue to radiate aconsiderable amount of heat afteryou have switched the engine off.This is a potential fire hazard.
FUEL FILLER FLAP
E75775
A
A
B
B
REFUELLING
CAUTION
Do not attempt to start theengine if you have filled the fuel
tank with the incorrect fuel. This coulddamage the engine. Have the systemchecked by a properly trainedtechnician immediately.
FUEL CONSUMPTION
The CO2 and fuel consumptionfigures are derived from laboratorytests according to EEC Directive80/1268/EEC and subsequentamendments and are carried out byall vehicle manufacturers.
They are intended as a comparisonbetween makes and models ofvehicles. They are not intended torepresent the real world fuelconsumption you may get from yourvehicle. Real world fuel consumptionis governed by many factorsincluding; driving style, high speeddriving, stop/start driving, airconditioning usage, the accessoriesfitted and towing etc.
Your Ford dealer can give you adviceon improving your fuel consumption.
86
Fuel and refuelling
TECHNICAL SPECIFICATIONS
Fuel consumption figures
CO2 emis-sionsCombinedExtra-
urbanUrban
Variant
g/kml/100 km(mpg)
l/100 km(mpg)
l/100 km(mpg)
1526.4 (44.1)5.1 (55.4)8.6 (32.8)1.25L Duratec
1546.5 (43.3)5.3 (53.3)8.5 (33.2)1.4L Duratec, 5-speedmanual transmission
1486.2 (45.6)5.2 (54.3)8 (35.3)1.4L Duratec, DurashiftEST
1576.6 (42.8)5.3 (53.3)8.9 (31.7)1.6L Duratec, 5-speedmanual transmission
1817.6 (37.2)6.1 (46.3)10.3 (27.4)1.6L Duratec, automatictransmission
1164.4 (64.2)3.9 (72.4)5.3 (53.3)1.4L Duratorq-TDCi, 5-speed manual transmis-sion, Stage III
1224.6 (61.4)4 (70.6)5.7 (49.6)1.4L Duratorq-TDCi, 5-speed manual transmis-sion, Stage IV
1144.3 (65.7)3.9 (72.4)5.1 (55.4)1.4L Duratorq-TDCi,Durashift EST
1194.5 (62.8)4 (70.6)5.5 (51.4)1.6L Duratorq-TDCi
87
Fuel and refuelling
MANUAL TRANSMISSION
5-speed manualtransmission
CAUTION
Do not apply any undue lateralforce to the gear lever when
changing from 5th to 4th gear. Thiscould lead to the inadvertentselection of 2nd gear and can causedamage to the transmission.
Selecting reverse gear
E75050
CAUTION
Do not engage reverse gearwhen the vehicle is moving. This
can cause damage to thetransmission.
Note: Fully depress the clutch pedaland wait for three seconds beforeyou select reverse gear.
Durashift EST
Selector lever positions
E90581
ReverseR
NeutralN
Drive (automated)D
Drive (manual)+/-
Drive modeA
WARNINGSApply the brakes before movingthe selector lever and keep
them applied until you are ready tomove off.
Select reverse only when yourvehicle is stationary and the
engine is at idle speed.
Note: A cold engine has a higher idlespeed. This will increase thetendency for your vehicle to creepwhen you have selected a drive gear.
The selected gear will be shown inthe information display. If it flashes,apply the brakes or press theaccelerator pedal to move off.
88
Transmission
Push the lever to the left (drive mode)to select manual drive or automateddrive.
Moving off
1. Release the parking brake.
2. Release the brake pedal andpress the accelerator pedal.
Stopping
1. Release the accelerator pedal andpress the brake pedal.
2. Apply the parking brake.
Kickdown
Press the accelerator pedal fully toselect the next highest gear foroptimum performance. Release theaccelerator pedal when you nolonger require kickdown.
AUTOMATICTRANSMISSION - 4-SPEED AUTOMATICTRANSMISSION (4F27E)
Selector lever positions
E83164
ParkP
ReverseR
NeutralN
DriveD
2nd Gear2
1st Gear1
WARNING
Apply the brakes before movingthe selector lever and keep
them applied until you are ready tomove off.
Note: A cold engine has a higher idlespeed. This will increase thetendency for your vehicle to creepwhen you have selected a drive gear.
89
Transmission
Press the button on the selector leverto select reverse and park.
The selector lever position will beshown in the information display.
Park
WARNINGSSelect park only when yourvehicle is stationary.
Apply the parking brake andselect park before leaving your
vehicle. Make sure that the selectorlever is latched in position.
Note: An audible warning will soundif you open the drivers door and youhave not selected park.
In this position, power is nottransmitted to the drive wheels andthe transmission is locked. You canstart the engine with the selectorlever in this position.
Reverse
WARNING
Select reverse only when yourvehicle is stationary and the
engine is at idle speed.
Neutral
In this position, power is nottransmitted to the drive wheels butthe transmission is not locked. Youcan start the engine with the selectorlever in this position.
Drive
Select drive to shift automaticallythrough the forward gears.
2nd Gear
Select 2, the transmission willautomatically shift between 2nd and1st gears only.
1st Gear
Select 1, the transmission will select1st gear only.
Hints on driving with anautomatic transmission
Moving off
1. Release the parking brake.
2. Release the brake pedal andpress the accelerator pedal.
Stopping
1. Release the accelerator pedal andpress the brake pedal.
2. Apply the parking brake.
Kickdown
Press the accelerator pedal fully withthe selector lever in the drive positionto select the next highest gear foroptimum performance. Release theaccelerator pedal when you nolonger require kickdown.
Overdrive
Note: The transmission is normallyin overdrive when drive is selected.
90
Transmission
E83165
When you are travelling in slowmoving traffic or climbing steepgradients there may be a tendencyfor the transmission to continuallyshift between 4th and 3rd gears. Ifthis condition should arise switch theoverdrive function off.
Note: The transmission will onlyselect between 1st, 2nd and 3rdgears if the overdrive function hasbeen switched off.
Drive modes
The transmission will select theappropriate gear for optimumperformance based on ambienttemperature, road gradient, vehicleload and driver input.
Emergency park positionrelease lever
Use the lever to move the selectorlever from the park position in theevent of an electrical malfunction orif your vehicle has a flat battery.
E83166
1. Remove the cover.
2. Insert a flat-bladed screwdriverinto the slot.
3. Push downwards on thescrewdriver to release the leverand move the selector lever fromthe park position.
4. Install the cover.
91
Transmission
PRINCIPLE OFOPERATION
Dual circuit braking system
E71353
WARNING
If a brake circuit fails, you willnotice a softer feel to the brake
pedal. Press the brake pedal firmlyand allow for increased stoppingdistances. Stop and have thischecked immediately. Do notcontinue your journey.
Your vehicle is fitted with a diagonallysplit, dual circuit brake system. If abrake circuit fails, the other remainsoperational.
Disc brakes
E71354
Wet brake discs result in reducedbraking efficiency. Dab the brakepedal when driving from a car washto remove the film of water.
ABS
WARNING
The ABS does not relieve you ofyour responsibility to drive with
due care and attention.
The ABS helps you to maintain fullsteering and directional stability whenyou brake heavily in an emergency,by preventing the road wheels fromlocking. The ABS monitors the speedof each road wheel and varies thepressure to each brake. The ABSoptimizes the tyre-to-road adhesionwhen you brake heavily.
HINTS ON DRIVING WITHABS
E71355
When the ABS is operating, the brakepedal will pulse. This is normal.Maintain pressure on the brakepedal.
92
Brakes
The ABS will not eliminate thedangers inherent when:• you drive too close to the vehicle
in front of you.• the vehicle is aquaplaning.• you take corners too fast.• the road surface is poor.
PARKING BRAKE
Applying the parking brake
E66567
WARNING
Make sure that the parkingbrake is applied before you
release the lever.
Note: Do not press the releasebutton when you apply the parkingbrake.
1. Press the brake pedal firmly.2. Pull the parking brake lever
upwards to its fullest extent.
Parking on a hill
If you have to park facing uphill, selectfirst gear and turn the front wheelsaway from the kerb. If you have topark facing downhill, select reversegear and turn the front wheelstowards the kerb.
Releasing the parkingbrake
1. Press the brake pedal firmly.2. Pull the parking brake lever
upwards slightly, press the releasebutton and push the leverdownwards.
93
Brakes
PRINCIPLE OFOPERATION
Electronic stabilityprogramme (ESP)
WARNING
ESP does not relieve you of yourresponsibility to drive with due
care and attention.
E72903
A A
AB
B
B
B
without ESPA
with ESPB
The ESP supports stability when thevehicle starts to slide away from yourintended path. This is performed bybraking individual wheels andreducing engine torque as needed.
The system also provides anenhanced traction control functionby reducing engine torque if thewheels spin when you accelerate.This improves your ability to pull awayon slippery roads or loose surfaces,and improves comfort by limitingwheel spin in hairpin bends.
Stability control (ESP) warninglamp
The ESP warning lamp will flash whenthe system is operating. SeeWarning lamps and indicators(page 57).
Emergency brake assist
WARNING
Emergency brake assist doesnot relieve you of your
responsibility to drive with due careand attention.
Emergency brake assist will detectwhen you brake heavily by measuringthe rate at which you press the brakepedal. It will provide maximumbraking efficiency as long as youpress the pedal. Emergency brakeassist can reduce stopping distancesin critical situations.
94
Stability control
USING STABILITYCONTROL
E94885
Press and hold the switch for onesecond. The switch will illuminate.
Press the switch again to turn thesystem on. The system will beswitched on automatically every timeyou switch the ignition on.
For item location: See Quick start(page 8).
95
Stability control
PRINCIPLE OFOPERATION
WARNING
The parking aid does not relieveyou of your responsibility to
drive with due care and attention.
CAUTIONSThe sensors may not detectobjects in heavy rain or other
conditions that cause disruptivereflections.
The sensors may not detectobjects with surfaces that absorb
ultrasonic waves.
The sensors may not detectobjects that are close to the
vehicle (approximately 30centimetres [11 inches] to the rearand above or below the sensors).
If you use a high pressure sprayto wash your vehicle, only spray
the sensors briefly from a distancenot less than 20 centimetres (8inches).
Note: The parking aid may emit falsetones if it detects a signal using thesame frequency as the sensors or ifthe vehicle is fully laden.
Note: The outer sensors may detectthe side walls of a garage. If thedistance between the outer sensorand the side wall remains constantfor three seconds, the tone willswitch off. As you continue, the innersensors will detect rearward objects.
USING THE PARKING AID
Note: Keep the sensors free fromdirt, ice and snow. Do not clean withsharp objects.
Switching the parking aidon and off
Note: The parking aid switches offautomatically when you start theengine or when you exceed 16 km/h(10 mph).
Note: Vehicles fitted with a trailertow module not approved by us maynot correctly detect obstacles.
Note: On vehicles fitted with a towball arm, the rear sensors aredeactivated automatically when anytrailer lamps (or lighting boards) areconnected to the 13-pin socket via atrailer tow module we haveapproved. On vehicles fitted with atrailer tow module not approved byus, you have to switch the parkingaid off using the switch.
Note: The front and rear sensors arealways activated or deactivatedtogether.
Note: On vehicles fitted withautomatic transmission, the parkingaid will not operate in position P.
The parking aid is per default off. Toswitch the parking aid on, press theswitch in the instrument panel orselect reverse gear.
The light in the switch illuminateswhen the parking aid is activated.
To turn it off, press the switch again.
96
Parking aid
Manoeuvring with theparking aid
E72902
CAUTIONSThe parking aid does not detectobstacles moving away from the
vehicle. They will only be detectedshortly after they start to movetowards the vehicle again.
Take particular care whenreversing with a tow ball arm or
rear fitted accessories e.g. a bicyclecarrier, as the rear parking aid will onlyindicate the distance from thebumper to the obstacle.
Note: If a high pitch warning tonesounds for three seconds and thelight in the switch is flashing, itindicates a malfunction. The systemwill be disabled. Have the systemchecked by properly trainedtechnicians.
You will hear an intermittent tone ata distance of up to 180 centimetres(71 inches) between the obstacle andrear bumper, 80 centimetres (31inches) between the obstacle andfront bumper and 60 centimetres (24inches) to the side. Decreasing thedistance accelerates the intermittenttone. A continuous tone will start ata distance of less than 30centimetres (11 inches).
You will hear an alternating tone fromthe front and rear if obstacles arecloser than 30 centimetres (11 inches)to the front and rear bumpers.
97
Parking aid
GENERAL INFORMATION
WARNINGSUse load securing straps to anapproved standard, e.g. DIN.
Make sure that you secure allloose items properly.
Place luggage and other loadsas low and as far forward as
possible within the luggage orloadspace.
Do not drive with the tailgate orrear door open. Exhaust fumes
may enter the vehicle.
Do not exceed the maximumfront and rear axle loads for your
vehicle.
LUGGAGE COVERS
CAUTION
Do not place objects on theluggage cover.
E72512
1. Release the straps from thetailgate.
2. Pull the luggage cover towardsyou and remove it.
ROOF RACKS AND LOADCARRIERS
Roof rack
WARNINGSIf you use a roof rack, the fuelconsumption of your vehicle will
be higher and you may experiencedifferent driving characteristics.
Read and follow themanufacturer’s instructions
when you are fitting a roof rack.
Switch stability control (ESP) on.
Inflate the tyres to the standardpressures. See Technical
specifications (page 140).
CAUTION
Do not exceed the maximumpermissible roof load. See
Weights (page 167).
Check the security of the roof rackand tighten its fittings as follows:
• before starting• after driving 50 kilometres (30
miles)• at 1 000 kilometres (600 miles)
intervals.
98
Load carrying
TOWING A TRAILER
WARNINGSDo not exceed the maximumvehicle and trailer weight stated
on the vehicle identification plate. SeeVehicle identification (page 166).
ST vehicles are not approvedfor trailer towing.
Note: Not all vehicles are suitable orapproved to have tow bars fitted.Check with your dealer first.
Place loads as low and central to theaxle(s) of the trailer as possible. If youare towing with an unladen vehicle,the load in the trailer should beplaced toward the nose, within themaximum nose load, as this gives thebest stability.
Note: The maximum trailer noseweight can be found on themanufacturers data plate on the towbar.
The stability of the vehicle to trailercombination is very much dependanton the quality of the trailer.
In high altitude regions, the stipulatedmaximum permitted gross trainweight must be reduced by 10% forevery 1 000 metres (3 281 feet).
Steep gradients
WARNING
The overrun brake on a trailer isnot controlled by ABS.
Change down a gear before youreach a steep downhill gradient.
DETACHABLE TOW BALL
WARNINGSNever leave the detached towball arm unsecured inside the
vehicle. This would increase the riskof injury in an accident.
Take special care when fittingthe tow ball arm as the safety of
the vehicle and the trailer dependson this.
E71328
A 13-pin trailer socket and the towball arm seat are providedunderneath the rear bumper. Turnthe trailer socket down through 90degrees until it engages in the endposition.
When not in use, always transportthe tow ball arm securely fastened inthe luggage compartment. Insert theplug into its seat.
99
Towing
Unlocking the tow ball armmechanism
WARNING
Do not use any tools formounting or dismounting the
tow ball arm. Do not modify the trailercoupling. Do not disassemble orrepair the tow ball arm.
E71329
2
1
3
1. Remove the protecting cap. Insertthe key and turn clockwise tounlock.
2. Hold the tow ball arm. Pull thehandwheel out and turn itclockwise until it clicks.
3. The red mark on the handwheelmust align with the green mark onthe tow ball.
4. Release the handwheel. The towball arm is unlocked.
Inserting the tow ball arm
1
2E71330
WARNING
The tow ball arm may only beinserted when completely
unlocked.
1. Pull out the plug.
2. Insert the tow ball arm verticallyand press it upwards until itengages (1). Do not hold yourhand near the handwheel.
3. The green mark on thehandwheel must align with thegreen mark on the tow ball.
4. To lock, turn the key anticlockwiseand remove the key (2).
5. Pull the protecting cap from thekey bow and press it onto thelock.
100
Towing
Driving with a trailer
E71331
A
B
WARNING
If any of the below conditionscannot be met, do not use the
tow bar and have it inspected by anexpert.
Before starting your journey, ensurethe tow ball arm is properly locked.Check that:
• the green marks are aligned• the handwheel (A) is correctly
fitted to the tow ball arm.• you have removed the key (B).• the tow ball arm is securely
positioned. It must not movewhen jerked.
Removing the tow ball arm
3
1E71332
2
Note: Unhitch the trailer.
1. Remove the protecting cap. Pressthe cap into the key bow. Insertthe key and unlock.
2. Hold the tow ball arm. Pull thehandwheel out and turn itclockwise against the stop.
3. Remove the tow ball arm.
4. Release the handwheel.
When unlocked in this way, the towball arm can be reinserted at anytime.
101
Towing
Driving without a trailer
WARNING
To avoid risk of injury, neverunlock the tow ball arm with the
trailer attached.
1. Remove the tow ball arm.
2. Insert the plug into its seat.
Maintenance
WARNING
Remove the tow ball arm andprotect the seat with the plug
before steam cleaning your vehicle.
Keep the system clean. Periodicallylubricate bearings, sliding surfaces,and locking balls with resin-freegrease or oil and the lock withgraphite.
Keep a note of the key number. Incase of loss, replacement keys areavailable from the manufacturer bystating the 4-digit key number.
102
Towing
GENERAL DRIVINGPOINTS
Vehicles with a dieselengine
If the low fuel level warning lampcomes on, refuel as soon as possible.If you continue driving withoutrefuelling, the engine will start to rununevenly. This indicates that you areabout to run out of fuel. Refuelimmediately.
RUNNING-IN
Tyres
WARNING
New tyres need to be run-in forapproximately 500 kilometres
(300 miles). During this time, you mayexperience different drivingcharacteristics.
Brakes and clutch
WARNING
Avoid heavy use of the brakesand clutch if possible for the first
150 kilometres (100 miles) in townand for the first 1 500 kilometres (1000 miles) on motorways.
Engine
CAUTION
Avoid driving too fast during thefirst 1 500 kilometres (1 000
miles). Vary your speed frequentlyand change up through the gearsearly. Do not labour the engine.
103
Driving hints
FUEL CUT-OFF SWITCH
Vehicles with a Duratecengine
Left-hand drive
E90981
Right-hand drive
E90982
The fuel supply may be cut off as aresult of an accident or suddenvibrations (e.g. collision whenparking).
The switch is located behind theglove box. Open the glove box andempty the contents. Press the sidesinwards and swivel the glove boxdownwards.
Resetting the switch
WARNING
Do not reset the fuel cut-offswitch if you see or smell leaking
fuel.
1. Turn the ignition switch to position0.
2. Check fuel system for leaks.
104
Status after a collision
3. If no fuel leak is apparent, resetthe switch by pushing in thebutton.
4. Turn the ignition switch to positionII. After a few seconds return thekey to position I.
5. Make a further check for leaks inthe fuel system.
INSPECTING SAFETYSYSTEM COMPONENTS
Seat belts
Belts subjected to strain, as a resultof an accident, should be renewedand the anchorages checked by aproperly trained technician.
105
Status after a collision
CHANGING A FUSE
WARNINGSDo not modify the electricalsystem of your vehicle in any
way. Have repairs to the electricalsystem and the replacement ofrelays and high current fuses carriedout by a properly trained technician.
Switch the ignition and allelectrical equipment off before
touching or attempting to change afuse.
CAUTION
Fit a replacement fuse with thesame rating as the one you have
removed.
Note: You can identify a blown fuseby a break in the filament.
Note: All fuses, except high currentfuses, are a push fit.
Note: A fuse puller is located in theengine compartment fuse box.
FUSE LABELS
E90985
A B
CD
Fuse numberA
Circuits protectedB
Location (L = left and R =right)
C
Fuse rating (Amperes)D
See Owner's handbook
Airbag
ABS
Headlamp dipped beam
Headlamp main beam
106
Fuses
Fog lamps
Lighting control
Windscreen wipers
Rear window wiper
Heated windscreen
Heated rear window
Heated exterior mirrors
Electric exterior mirrors
Electric windows
Not used
Heated seats
Blower motor
Air conditioning
Cigar lighter
Horn
Daytime running lamps
Automatic transmission orDurashift EST
Engine management(diesel) or catalyticconverter
Starter motor
Audio system anddiagnostic connector
Engine management orelectronic module
Fuel pump
Auxiliary heater, glow plugsand fuel injection pump relay
Battery and charging system
Instrument cluster, batterysaver, number plate lamp,generic electronic module
(GEM)
Side and tail lamps
Central locking and alarmhorn
107
Fuses
Hazard warning flashers anddirection indicators
Ignition
Trailer towing module
Durashift EST
Brake lamps
Reversing lamp
FUSE BOX LOCATIONS
Central fuse box
The central fuse box is locatedbehind the glove box. Open the glovebox and empty the contents. Pressthe sides inwards and swivel theglove box downwards.
108
Fuses
TOWING POINTS
Front towing eye
E87280
The screw-in towing eye is attachedto the vehicle jack in the luggagecompartment. Keep the towing eyewith the vehicle at all times.
CAUTION
The screw-in towing eye has aleft-hand thread. Turn it
anticlockwise to install it.
Prise off the cover and install thetowing eye.
TOWING THE VEHICLEON FOUR WHEELS
All vehicles
WARNINGSSwitch the ignition on when yourvehicle is being towed. The
steering lock will engage and thedirection indicators and brake lampswill not work if you do not.
The brake servo and the powersteering pump do not operate
unless the engine is running. Pressthe brake pedal harder and allow forincreased stopping distances andheavier steering.
CAUTIONSToo much tension in the towrope could cause damage to
your vehicle or the vehicle that istowing.
Do not use a rigid tow bar on thefront towing eye.
Drive off slowly and smoothly withoutjerking the vehicle that is towing.
Vehicles with a DurashiftEST
CAUTION
Select neutral when your vehicleis being towed.
109
Vehicle recovery
Vehicles with an automatictransmission
CAUTIONSDo not tow your vehicle fasterthan 50 km/h (30 mph) or further
than 50 kilometres (30 miles).
If a speed of 50 km/h (30 mph)and a distance of 50 kilometres
(30 miles) is to be exceeded the drivewheels must be lifted clear of theground.
In the event of a mechanicalfailure of the transmission the
drive wheels must be lifted clear ofthe ground.
Do not tow your vehiclebackwards.
Select neutral when your vehicleis being towed.
110
Vehicle recovery
GENERAL INFORMATION
Have your vehicle serviced regularlyto help maintain its roadworthinessand resale value. There is a largenetwork of Ford Authorised Repairersthat are there to help you with theirprofessional servicing expertise. Webelieve that their specially trainedtechnicians are best qualified toservice your vehicle properly andexpertly. They are supported by awide range of highly specialised toolsdeveloped specifically for servicingyour vehicle.
In addition to regular servicing, werecommend that you carry out thefollowing additional checks.
WARNINGSSwitch the ignition off beforetouching or attempting
adjustment of any kind.
Do not touch the electronicignition system parts after you
have switched the ignition on orwhen the engine is running. Thesystem operates at high voltage.
Keep your hands and clothingclear of the engine cooling fan.
Under certain conditions, the fan maycontinue to run for several minutesafter you have switched the engineoff.
Daily checks
• Exterior lamps.• Interior lamps.• Warning lamps and indicators.
Check when refuelling
• Engine oil level. See Engine oilcheck (page 118).
• Brake fluid level. See Brake andclutch fluid check (page 120).
• Washer fluid level. See Washerfluid check (page 121).
• Tyre pressures (when cold). SeeWheels and tyres (page 129).
• Tyre condition. See Wheels andtyres (page 129).
Monthly checks
• Engine coolant level (engine cold).See Engine coolant check(page 119).
• Pipes, hoses and reservoirs forleaks.
• Power steering fluid level. SeePower steering fluid check(page 120).
• Air conditioning operation.• Parking brake operation.• Horn operation.• Tightness of wheel nuts. See
Wheels and tyres (page 129).
111
Maintenance
OPENING AND CLOSINGTHE BONNET
Opening the bonnet
E90413
1
1. Pull the lever.
2
E90414
2. Raise the bonnet slightly and pullthe catch towards you.
E78143
5
4
3. Open the bonnet and support itwith the strut.
Closing the bonnet
Note: Make sure that the bonnet isclosed properly.
Lower the bonnet and allow it to dropfrom under its own weight for the last20 – 30 centimetres.
112
Maintenance
ENGINE COMPARTMENT OVERVIEW - 1.25LDURATEC-16V (SIGMA)/1.4L DURATEC-16V(SIGMA)/1.6L DURATEC-16V (SIGMA)
A B C D FE
GHJ IE90583
Engine coolant reservoir*: See Engine coolant check (page 119).A
Brake and clutch fluid reservoir (right-hand drive)*: See Brake andclutch fluid check (page 120).
B
Engine oil filler cap*: See Engine oil check (page 118).C
113
Maintenance
Engine compartment fuse box. See Fuses (page 106).D
Brake and clutch fluid reservoir (right-hand drive)*: See Brake andclutch fluid check (page 120).
E
Battery: No maintenance necessary.F
Windscreen and rear window washer fluid reservoir: See Washerfluid check (page 121).
G
Air cleaner: No maintenance necessary.H
Engine oil dipstick*: See Engine oil check (page 118).I
Power steering fluid reservoir: See Power steering fluid check(page 120).
J
* The filler caps and the engine oil dipstick are coloured for easy identification.
114
Maintenance
ENGINE COMPARTMENT OVERVIEW - 1.4LDURATORQ-TDCI (DV) DIESEL
A B C D FE
GHJ IE90585
Engine coolant reservoir*: See Engine coolant check (page 119).A
Brake and clutch fluid reservoir (right-hand drive)*: See Brake andclutch fluid check (page 120).
B
Engine oil filler cap*: See Engine oil check (page 118).C
Engine compartment fuse box. See Fuses (page 106).D
115
Maintenance
Brake and clutch fluid reservoir (right-hand drive)*: See Brake andclutch fluid check (page 120).
E
Battery: No maintenance necessary.F
Windscreen and rear window washer fluid reservoir: See Washerfluid check (page 121).
G
Air cleaner: No maintenance necessary.H
Engine oil dipstick*: See Engine oil check (page 118).I
Power steering fluid reservoir: See Power steering fluid check(page 120).
J
* The filler caps and the engine oil dipstick are coloured for easy identification.
116
Maintenance
ENGINE COMPARTMENT OVERVIEW - 1.6LDURATORQ-TDCI (DV) DIESEL
A B C D FE
GHJ IE90586
Engine coolant reservoir*: See Engine coolant check (page 119).A
Brake and clutch fluid reservoir (right-hand drive)*: See Brake andclutch fluid check (page 120).
B
Engine oil filler cap*: See Engine oil check (page 118).C
Engine compartment fuse box. See Fuses (page 106).D
117
Maintenance
Brake and clutch fluid reservoir (right-hand drive)*: See Brake andclutch fluid check (page 120).
E
Battery: No maintenance necessary.F
Windscreen and rear window washer fluid reservoir: See Washerfluid check (page 121).
G
Air cleaner: No maintenance necessary.H
Engine oil dipstick*: See Engine oil check (page 118).I
Power steering fluid reservoir: See Power steering fluid check(page 120).
J
* The filler caps and the engine oil dipstick are coloured for easy identification.
ENGINE OIL CHECK
CAUTION
Do not use oil additives or otherengine treatments. Under certain
conditions, they could damage theengine.
Note: The oil consumption of newengines reaches its normal level afterapproximately 5 000 kilometres (3000 miles).
Checking the oil level
1.25L, 1.4L and 1.6L Duratec
E87452
1.4L Duratorq-TDCi
E90411
118
Maintenance
1.6L Duratorq-TDCi
E90412
Note: Check the oil level beforestarting the engine.
Note: Make sure the vehicle is onlevel ground.
Note: Oil expands when it is hot. Thelevel may therefore extend a fewmillimetres beyond the MAX mark.
Remove the dipstick and wipe it witha clean, lint free cloth. Replace thedipstick and remove it again to checkthe oil level.
Make sure that the oil level isbetween the MIN and the MAXmarks. If it is, you do not need to topup. If it is at the MIN mark, top upimmediately.
Topping up the oil
E73940
WARNING
Do not remove the oil filler capwhen the engine is running.
Remove the oil filler cap.
WARNING
Do not top up further than theMAX mark.
Top up with oil that meets the Fordspecification. See Technicalspecifications (page 122).
Replace the oil filler cap. Turn it untilyou feel a strong resistance.
ENGINE COOLANTCHECK
Checking the coolant level
E73703
CAUTION
Make sure that the coolant levelis between the MIN and the
MAX marks.
119
Maintenance
Note: Coolant expands when it ishot. The level may therefore extendbeyond the MAX mark.
Topping up the coolant
WARNING
Do not remove the coolantreservoir cap when the engine
is hot. Wait for the engine to cooldown.
Unscrew the cap slowly. Anypressure will escape slowly as youunscrew the cap.
WARNINGSOnly add coolant when theengine is cold. If the engine is
hot, wait 10 minutes for the engine tocool down.
Do not allow coolant to touchyour skin or eyes. If this
happens, rinse the affected areasimmediately with plenty of water andcontact your doctor.
CAUTION
Do not spill coolant on any partof the engine.
Only add coolant that meets the Fordspecification. See Technicalspecifications (page 122).
BRAKE AND CLUTCHFLUID CHECK
WARNING
Do not allow brake fluid to touchyour skin or eyes. If this
happens, rinse the affected areasimmediately with plenty of water andcontact your doctor.
The brake and clutch systems aresupplied from the same reservoir.
Make sure that the brake fluid levelis between the MIN and the MAXmarks.
POWER STEERING FLUIDCHECK
E69130
Switch off the engine. With thesteering system at normal operatingtemperature, the fluid level shouldcome up to the MAX mark.
If it drops below the MIN mark, topup with the specified fluid.
120
Maintenance
WASHER FLUID CHECK
E73230
The front and rear washer systemsare supplied from the same reservoir.
Refit the washer fluid reservoir capsecurely after topping up.
Washer jets
To ensure the system functionsproperly, keep the washer jets freeof snow and ice.
121
Maintenance
TECHNICAL SPECIFICATIONS
Vehicle fluids
SpecificationRecommended fluidItem
WSS-M2C913-BFord or MotorcraftFormula E SAE 5W-30
Engine Oil1
Engine oil
WSS-M2C195-AFord or MotorcraftPower Steering Fluid
Power steering fluid
WSS-M97B44-DMotorcraft SuperPlusAntifreeze
Antifreeze
CAUTION
Do not use oils which do not meet the specifications or requirements.Use of unsuitable oil may lead to engine damage which is not covered by
the Ford Warranty.
1 You can use an alternative SAE 5W-30 engine oil, providing it meets thespecification defined by WSS-M2C913-B.
Note: If you operate your vehicle in temperatures below -20°C, you mustnot use SAE 10W-40 engine oil.
Topping up the oil: If you are unable to find an oil that meets thespecification defined by WSS-M2C913-B, you must use SAE 5W-30(preferred), SAE 5W-40 or SAE 10W-40 that meets the specification definedby either ACEA A1/B1 (preferred) or ACEA A3/B3. Using these oils can resultin longer engine cranking periods, reduced engine performance, reducedfuel economy and increased emission levels.
Capacities
Capacity in litres(gallons)ItemVariant
MAX markPower steering systemAll
2.5 (0.5)Windscreen and rearwindow washer systemAll
45 (9.9)Fuel tankPetrol
122
Maintenance
Capacity in litres(gallons)ItemVariant
43 (9.5)Fuel tankDiesel
3.75 (0.8)Engine lubricationsystem - including the oilfilter (EFL500)
1.25L Duratec
3.8 (0.8)Engine lubricationsystem - including the oilfilter (EFL10)
1.25L Duratec
3.5 (0.8)Engine lubricationsystem - excluding theoil filter
1.25L Duratec
5 (1.1)Engine cooling system1.25L Duratec
3.75 (0.8)Engine lubricationsystem - including the oilfilter (EFL500)
1.4L Duratec
3.8 (0.8)Engine lubricationsystem - including the oilfilter (EFL10)
1.4L Duratec
3.5 (0.8)Engine lubricationsystem - excluding theoil filter
1.4L Duratec
5 (1.1)Engine cooling system1.4L Duratec
4.1 (0.9)Engine lubricationsystem - including the oilfilter (EFL10)
1.6L Duratec
4.25 (0.9)Engine lubricationsystem - including the oilfilter (EFL600)
1.6L Duratec
3.75 (0.8)Engine lubricationsystem - excluding theoil filter
1.6L Duratec
5 (1.1)Engine cooling system1.6L Duratec
123
Maintenance
Capacity in litres(gallons)ItemVariant
3.8 (0.8)Engine lubricationsystem - including the oilfilter
1.4L Duratorq-TDCi
3.4 (0.8)Engine lubricationsystem - excluding theoil filter
1.4L Duratorq-TDCi
5.5 (1.2)Engine cooling system1.4L Duratorq-TDCi
3.85 (0.8)Engine lubricationsystem - including the oilfilter
1.6L Duratorq-TDCi
3.45 (0.8)Engine lubricationsystem - excluding theoil filter
1.6L Duratorq-TDCi
6 (1.3)Engine cooling system1.6L Duratorq-TDCi
124
Maintenance
CLEANING THEEXTERIOR
WARNING
If you use a car wash with awaxing cycle, make sure that
you remove the wax from thewindscreen.
CAUTIONSSome car wash installations usewater at high pressure. This
could damage certain parts of yourvehicle.
Remove the aerial before usingan automatic car wash.
Switch the heater blower off toprevent contamination of the
fresh air filter.
We recommend that you wash yourvehicle with a sponge and lukewarmwater containing a car shampoo.
Cleaning the headlamps
CAUTIONSDo not scrape the headlamplenses or use abrasives or
chemical solvents to clean them.
Do not wipe the headlampswhen they are dry.
Cleaning the rear window
CAUTION
Do not scrape the inside of therear window or use abrasives or
chemical solvents to clean it.
Use a clean, lint free cloth or a dampchamois leather to clean the insideof the rear window.
Cleaning the chrome trim
CAUTION
Do not use abrasives or chemicalsolvents. Use soapy water.
Body paintworkpreservation
CAUTIONSDo not polish your vehicle instrong sunshine.
Do not allow polish to touchplastic surfaces. It could be
difficult to remove.
Do not apply polish to thewindscreen or rear window. This
could cause the wipers to becomenoisy and they may not clear thewindow properly.
We recommend that you wax thepaintwork once or twice a year.
125
Vehicle care
CLEANING THE INTERIOR
Seat belts
WARNINGSDo not use abrasives, orchemical solvents to clean
them.
Do not allow moisture topenetrate the seat belt retractor
mechanism.
Clean the seat belts with interiorcleaner or water applied with a softsponge. Let the seat belts drynaturally, away from artificial heat.
Instrument cluster screens,LCD screens, radioscreens
WARNING
Do not use abrasives, orchemical solvents to clean
them.
REPAIRING MINOR PAINTDAMAGE
CAUTION
Remove apparently harmlesslooking substances from the
paintwork immediately (e.g. birddroppings, tree resins, insectremains, tar spots, road salt andindustrial fall out).
You should repair paintwork damagecaused by stones from the road orminor scratches as soon as possible.A choice of products is available fromyour Ford Dealer. Read and followthe manufacturer’s instructions.
126
Vehicle care
BATTERY CARE
The battery requires very littlemaintenance. The fluid level ischecked regularly during the routineservice inspections.
USING BOOSTERCABLES
CAUTIONSConnect batteries with only thesame nominal voltage.
Always use booster cables withinsulated clamps and adequate
size cable.
Do not disconnect the batteryfrom the vehicle’s electrical
system.
To connect the boostercables
A
B
D C
E90587
Flat battery vehicleA
Booster battery vehicleB
127
Vehicle battery
Positive connection cableC
Negative connection cableD
Vehicles with a petrol engine
CAUTIONSDo not connect to thenegative (–) terminal of the
flat battery.
Make sure that the jump leadsare clear of any moving parts.
1. Position the vehicles so that theydo not touch one another.
2. Switch off the engine and anyelectrical equipment.
3. Connect the positive (+) terminalof vehicle A with the positive (+)terminal of vehicle B (cable C).
4. Connect the negative (-) terminalof vehicle B to the engine blockor engine mount of vehicle A(cable D), as far from the batteryas possible.
Vehicles with a diesel engine
CAUTIONSDo not connect to thenegative (–) terminal of the
flat battery.
Make sure that the jump leadsare clear of any moving parts.
1. Position the vehicles so that theydo not touch one another.
2. Switch off the engine and anyelectrical equipment.
3. Connect the positive (+) terminalof vehicle A with the positive (+)terminal of vehicle B (cable C).
4. Connect the negative (-) terminalof vehicle B to the turbochargerof vehicle A (cable D).
To start the engine
1. Run the engine of vehicle B atmoderately high speed.
2. Start the engine of vehicle A.
3. Run both vehicles for a minimumof three minutes beforedisconnecting the leads.
CAUTION
Do not switch on the headlampswhen disconnecting the cables.
The peak voltage could blow thebulbs.
Disconnect the cables in the reverseorder.
128
Vehicle battery
GENERAL INFORMATION
CAUTIONSUse only approved wheel andtyre sizes. Using other sizes
could damage the vehicle and willmake the National Type Approvalinvalid.
If you change the diameter of thetyres from that fitted at the
factory, the speedometer may notdisplay the correct speed. Take thevehicle to your dealer to have theengine management systemreprogrammed.
A decal with tyre pressure data islocated in the driver’s door openingat the B-pillar.
Check and set the tyre pressure atthe ambient temperature in whichyou are intending to drive the vehicleand when the tyres are cold.
Comfort tyre pressures
WARNING
If the vehicle is used with a roofload, is fully laden or is driven at
speeds in excess of 160 km/h (100mph) the tyres must be set to thestandard tyre pressure settings.
Driving at comfort tyre pressures willimprove ride comfort; however it willalter the driving characteristics andfuel consumption of the vehicle.
For optimum dynamic performancestandard pressure settings arerecommended.
CHANGING A ROADWHEEL
Spare wheel
If the spare wheel differs from theother fitted wheels, these rules mustbe followed:
WARNINGSDo not exceed 80 km/h (50mph).
Drive the shortest possibledistances before having the
spare wheel changed.
Do not fit more than one sparewheel on your vehicle at any
one time.
Do not use snow chains on thistype of wheel.
Note: The spare wheel is locatedunder the floor cover in the luggagecompartment.
Locking wheel nuts
You can obtain a replacement lockingwheel nut key and replacementlocking wheel nuts from your dealerusing the reference numbercertificate.
Vehicle jack
WARNINGSThe vehicle jack supplied withyour vehicle should only be used
when changing a wheel inemergency situations.
129
Wheels and tyres
WARNINGSBefore using the vehicle jack,check that it is not damaged or
deformed and that the thread islubricated and free from foreignmatter.
Never place anything betweenthe jack and the ground, or the
jack and the vehicle.
Your vehicle jack and wheel braceare located in the spare wheel well.
Note: Vehicles with a tyre repair kitor run flat tyres are not equipped witha vehicle jack or a wheel brace.
It is recommended to use aworkshop type hydraulic jack forchanging between summer andwinter tyres.
Note: Use a jack with a minimumlifting capacity of 1.5 tonnes and alifting plate with a minimum diameterof 80 millimetres (3.1 inches).
Jacking and lifting points
CAUTION
Use only the specified jackingpoints. If you use other positions,
you may damage the body, steering,suspension, engine, braking systemor the fuel lines.
E92658
A
B
130
Wheels and tyres
Emergency use onlyA
MaintenanceB
E93184
A
Indentations in the sills A show thelocation of the jacking points.
E92932
E93020
Note: If your vehicle is fitted with sideskirts, remove the cover beforepositioning the vehicle jack.
Removing a road wheel
WARNINGSPark your vehicle in such aposition that neither the traffic
nor you are hindered or endangered.
Set up a warning triangle.
Make sure that the vehicle is onfirm, level ground with the
wheels pointing straight ahead.
Switch off the ignition and applythe parking brake.
If your vehicle has a manualtransmission, select first or
reverse gear. If it has an automatictransmission, select park.
131
Wheels and tyres
WARNINGSIf your vehicle is fitted with aDurashift EST transmission,
select a gear before switching off theignition.
Have the passengers leave thevehicle.
Secure the diagonally oppositewheel with an appropriate block
or wheel chock.
Do not work underneath thevehicle when it is supported only
by a jack.
Make sure that the jack isvertical to the jacking point and
the base is flat on the ground.
CAUTION
Do not lay alloy wheels facedown on the ground, this will
damage the paint.
1. Insert the flat end of the wheelbrace between the rim and thehub cover and carefully removethe hub cap or cover.
E90922
2. Install the locking wheel nut key.
3. Fully extend the wheel brace ifapplicable.
4. Slacken the wheel nuts.
5. Jack up the vehicle until the tyreis clear of the ground.
6. Remove the wheel nuts and thewheel.
Installing a road wheel
WARNINGSUse only approved wheel andtyre sizes. Using other sizes
could damage the vehicle and willmake the National Type Approvalinvalid. See Technicalspecifications (page 140).
132
Wheels and tyres
WARNINGSMake sure that the arrows ondirectional tyres point in the
direction of rotation when the vehicleis moving forwards. If you have to fita spare wheel with the arrowspointing in the opposite direction,have the tyre refitted in the correctdirection by a properly trainedtechnician.
CAUTION
Do not install alloy wheels usingwheel nuts designed for use with
steel wheels.
Note: Make sure the wheel and hubcontact surfaces are free fromforeign matter.
Note: Make sure that the cones onthe wheel nuts are against the wheel.
1. Install the wheel.
2. Install the wheel nuts finger tight.
E90922
3. Install the locking wheel nut key.
1 2
3
4
E90589
4. Partially tighten the wheel nuts inthe sequence shown.
5. Lower the vehicle and remove thejack.
6. Fully tighten the wheel nuts in thesequence shown. SeeTechnical specifications(page 140).
7. Install the hub cap or cover usingthe ball of your hand.
WARNING
Have the wheel nuts checkedfor tightness and the tyre
pressure checked as soon aspossible.
TYRE REPAIR KIT
Your vehicle may not have a sparetyre. In this case it will have anemergency tyre repair kit that can beused to repair one flat tyre.
The tyre repair kit is located in thespare wheel well.
133
Wheels and tyres
General information
WARNINGSDepending on the type andextent of tyre damage, some
tyres can only be partially sealed ornot sealed at all. Loss of tyrepressure can affect vehicle handling,leading to loss of vehicle control.
Do not use the tyre repair kit ifthe tyre has already been
damaged as a result of being drivenunder inflated.
Do not try to seal damage otherthan that located within the
visible tread of the tyre.
Do not try to seal damage to thetyre’s sidewall.
The tyre repair kit seals most tyrepunctures [with a diameter of up tosix millimetres (1/4 inch)] totemporarily restore mobility.
Observe the following rules whenusing the kit:
• Drive with caution and avoidmaking sudden steering ordriving manoeuvres,especially if the vehicle is heavilyloaded or you are towing a trailer.
• The kit will provide you with anemergency temporary repair,enabling you to continue yourjourney to the next vehicle or tyredealer, or to drive a maximumdistance of 200 kilometres(125 miles).
• Do not exceed a maximumspeed of 80 km/h (50 mph).
• Keep the kit out of the reach ofchildren.
• Only use the kit when the ambienttemperature is between –30°C(-22°F) and +70°C (+158°F).
Using the tyre repair kit
WARNINGSCompressed air can act as anexplosive or propellant.
Never leave the tyre repair kitunattended while in use.
CAUTION
Do not keep the compressoroperating for more than 10
minutes.
Note: Use the tyre repair kit only forthe vehicle with which it was supplied.
• Park your vehicle at the roadsideso that you do not obstruct theflow of traffic and so that you areable to use the kit without beingin danger.
• Apply the parking brake, even ifyou have parked on a level road,to make sure that the vehicle willnot move.
• Do not attempt to remove foreignobjects like nails or screwspenetrating the tyre.
134
Wheels and tyres
• Leave the engine running whilethe kit is in use, but not if thevehicle is in an enclosed or poorlyventilated area (for example,inside a building). In thesecircumstances, switch thecompressor on with the engineturned off.
• Replace the sealant bottle with anew one before the expiry date(see top of bottle) is reached.
• Inform all other users of thevehicle that the tyre has beentemporarily sealed with the tyrerepair kit and make them awareof the special driving conditions tobe observed.
Inflating the tyre
WARNINGSCheck the sidewall of the tyreprior to inflation. If there are any
cracks, bumps or similar damage, donot attempt to inflate the tyre.
Do not stand directly beside thetyre while the compressor is
pumping.
WARNINGSWatch the sidewall of the tyre.If any cracks, bumps or similar
damage appear, turn off thecompressor and let the air out bymeans of the pressure relief valve B.Do not continue driving with this tyre.
The sealant contains naturalrubber latex. Avoid contact with
skin and clothing. If this happens,rinse the affected areas immediatelywith plenty of water and contact yourdoctor.
If the tyre inflation pressure doesnot reach 1.8 bar (26 psi) within
seven minutes, the tyre may havesuffered excessive damage, makinga temporary repair impossible. In thiscase, do not continue driving with thistyre.
CAUTION
Screwing the bottle onto thebottle holder will pierce the seal
of the bottle. Do not unscrew thebottle from the holder as the sealantwill escape.
135
Wheels and tyres
E94973
B
J
I
F
E
C
KA
G
HD
Protective capA
Pressure relief valveB
HoseC
Orange capD
136
Wheels and tyres
Bottle holderE
Pressure gaugeF
Power plug with cableG
Compressor switchH
LabelI
Bottle lidJ
Sealant bottleK
1. Open the lid of the tyre repair kit.
2. Peel off the label I showing themaximum permissible speed of80 km/h (50 mph) from the casingand attach it to the instrumentpanel in the driver’s field of view.Make sure the label does notobscure anything important.
3. Take the hose C and the powerplug with cable G out of the kit.
4. Unscrew the orange cap D andthe bottle lid J.
5. Screw the sealant bottle Kclockwise into the bottle holder Efully tight.
6. Remove the valve cap from thedamaged tyre.
7. Detach the protective cap A fromthe hose C and screw the hoseC firmly onto the valve of thedamaged tyre.
8. Make sure that the compressorswitch H is in position 0.
9. Insert the power plug G into thecigar lighter socket or auxiliarypower socket. See Cigarlighter (page 79). See Cigarlighter (page 79).
10. Start the engine.
11. Move the compressor switch Hto position 1.
12. Inflate the tyre for no longer thanseven minutes to an inflationpressure of minimum 1.8 bar(26 psi) and a maximum of3.5 bar (51 psi). Move thecompressor switch H to position0 and check the current tyrepressure with pressure gaugeF.
13. Remove the power plug G fromthe cigar lighter socket orauxiliary power socket.
14. Quickly unscrew the hose Cfrom the tyre valve and replacethe protective cap A. Fasten thevalve cap again.
15. Leave the sealant bottle K in thebottle holder E.
16. Make sure the kit, the bottle lidand the orange cap are storedsafely, but still easily accessiblein the vehicle. The kit will berequired again when you checkthe tyre pressure.
137
Wheels and tyres
17. Immediately drive approximatelythree kilometres (two miles) sothat the sealant can seal thedamaged area.
Note: When pumping in the sealantthrough the tyre valve, the pressuremay rise up to 6 bar (87 psi) but willdrop again after about 30 seconds.
WARNING
If you experience heavyvibrations, unsteady steering
behaviour or noises while driving,reduce your speed and drive withcaution to a place where it is safe foryou to stop the vehicle. Recheck thetyre and its pressure. If the tyrepressure is less than 1.3 bar (19 psi)or if there are any cracks, bumps orsimilar damage visible, do notcontinue driving with this tyre.
Checking the tyre pressure
1. Stop the vehicle after drivingapproximately three kilometres(two miles). Check, and wherenecessary, adjust the pressure ofthe damaged tyre.
2. Attach the kit and read the tyrepressure from the pressure gaugeF.
3. If the pressure of the sealant-filledtyre is 1.3 bar (19 psi) or more,adjust it to the specified pressure.See Technical specifications(page 140).
4. Follow the inflation procedureonce again to top up the tyre.
5. Check the tyre pressure againfrom the pressure gauge F. If thetyre pressure is too high, deflatethe tyre to the specified pressureusing the pressure relief valve B.
6. Once you have inflated the tyre toits correct tyre pressure, movethe compressor switch H toposition 0, remove the powerplug G from the socket, unscrewthe hose C, fasten the valve capand replace the protective cap A.
7. Leave the sealant bottle K in thebottle holder E and store the kitaway safely in its original location.
8. Drive to the nearest tyre specialistto get the damaged tyre replaced.Before the tyre is removed fromthe rim, inform your tyre dealerthat the tyre contains sealant.Renew the kit as soon as possibleafter it has been used once.
Note: Remember that emergencyroadside tyre repair kits only providetemporary mobility. Regulationsconcerning tyre repair after usage oftyre repair kit may differ from countryto country. You should consult a tyrespecialist for advice.
WARNING
Before driving, make sure thetyre is adjusted to the
recommended inflation pressure.See Technical specifications(page 140). Monitor the tyre pressureuntil the sealed tyre is replaced.
138
Wheels and tyres
Empty sealant bottles can bedisposed of together with normalhousehold waste. Return remains ofsealant to your dealer or dispose ofit in compliance with local wastedisposal regulations.
TYRE CARE
E70415
To make sure the front and rear tyresof your vehicle wear evenly and lastlonger, we recommend that youswap the tyres from front to rear andvice versa at regular intervals ofbetween 5 000 and 10 000 km (3000 and 6 000 miles).
CAUTION
Do not scrub the sidewalls of thetyres when you are parking.
If you have to mount a kerb, do soslowly and approach it with thewheels at right-angles to the kerb.
Examine the tyres regularly for cuts,foreign objects and uneven wear ofthe tread. Uneven wear could meanthat the wheel alignment is outsidespecification.
Check the tyre pressures (includingthe spare) when cold, every twoweeks.
USING WINTER TYRES
CAUTION
Make sure that you use thecorrect wheel nuts for the type
of wheel the winter tyres are fitted to.
If winter tyres are used, make surethat the tyre pressures are correct.See Technical specifications(page 140).
USING SNOW CHAINS
WARNINGSDo not exceed 50 km/h(30 mph).
Do not use snow chains onsnow-free roads.
Only fit snow chains to 14 x 5.5inch steel wheels with 185/60 R
14 winter tyres.
CAUTION
If your vehicle is fitted with wheeltrims, remove them before fitting
snow chains.
Note: The ABS will continue tooperate normally.
Only use small link snow chains.
Only use snow chains on the frontwheels.
139
Wheels and tyres
TECHNICAL SPECIFICATIONS
Wheel nut torque
Specification Nm (lb-ft)Variant
90 (66)All
Tyre pressures (cold tyres)
Up to 80 km/h (50 mph)
Tyre pressures
Full loadNormal load
Tyre sizeVariant RearFrontRearFront
bar(lbf/in²)
bar(lbf/in²)
bar(lbf/in²)
bar(lbf/in²)
3 (43)3 (43)3 (43)3 (43)175/65 R 14All
4.2 (61)4.2 (61)4.2 (61)4.2 (61)T125/80 R 15All
Comfort pressures - Up to 160 km/h (100 mph)
Tyre pressures
Full loadNormal load
Tyre sizeVariant RearFrontRearFront
bar(lbf/in²)
bar(lbf/in²)
bar(lbf/in²)
bar(lbf/in²)
2.8 (41)2.5 (36)1.8 (26)2 (29)195/60 R 15All
2.8 (41)2.5 (36)1.8 (26)2 (29)195/55 R 16All
140
Wheels and tyres
Standard pressures - All speeds
Tyre pressures
Full loadNormal load
Tyre sizeVariant RearFrontRearFront
bar(lbf/in²)
bar(lbf/in²)
bar(lbf/in²)
bar(lbf/in²)
2.8 (41)2.5 (36)2.2 (32)2.4 (35)185/60 R 14All
2.8 (41)2.5 (36)2.2 (32)2.4 (35)195/60 R 15All
2.8 (41)2.5 (36)2.2 (32)2.4 (35)195/55 R 16All
141
Wheels and tyres
GENERAL INFORMATION
This section describes the functionsand features of the Bluetooth mobilephone and voice control system.
The section covers the followingvariations:
• a mobile phone with a mobilephone cradle without voicecontrol
• a Bluetooth and voice controlsystem with a mobile phonecradle
• a Bluetooth and voice controlsystem without a mobile phonecradle.
The Bluetooth mobile phone part ofthe system provides interaction withthe audio or navigation system andyour mobile phone. It allows you touse the audio or navigation systemto make and receive calls withouthaving to use your mobile phone.
The voice control part of the systemcan be used to control:
• mobile phone calls• audio system functions• vehicle climate control functions.
Note: The mobile phone does notswitch off immediately after theignition key is turned off: the powerdown delay is preset to 10 minutes.The time period can be adjusted tobetween 0 and 60 minutes. This,depending on your mobile phone,can be achieved by creating aphonebook entry on your mobilephone with the name Timer and therequired delay as it's number.
If the Bluetooth and voice control isused for an extended period of timewhen the vehicle is stationary, makesure that the engine is running toavoid draining the battery
TELEPHONE SETUP
Requirements for cradleconnection
Your phone must be fitted in a mobilephone holder before it can be usedas a cradle phone with yourhandsfree/voice control system. Youwill be able to purchase the correctholder for your phone from yourdealer.
Placing your phone in thecradle
Note: Your phone must be fitted ina mobile phone holder to allow youto connect the phone to the cradle.
Connect your phone to the cradle.
1. Place the base of the phone in thecradle connection.
Note: Make sure that the phone ispushed fully rearwards in the cradle.
142
Telephone
2. Push the phone downwards untila click is heard.
2
1
E87688
Note: The connection to the systemwill be displayed on your phone.
Phonebook
After start up access to thephonebook can be delayed for up totwo minutes.
Phonebook categories
Depending on your phonebook entry,different categories can be displayedin the audio or navigation unit.
For example:
MobileM
OfficeO
HomeH
FaxF
Note: Entries may be displayedwithout a category attachment.
The category can also be indicatedas an icon:
Phone
Mobile
Home
Office
Fax
Making a phone an activephone
When using the system for the firsttime, no phone is connected to thesystem.
After switching on the ignition thecradle phone and the Bluetoothphone are recognized differently bythe system.
Bluetooth phone
After bonding a Bluetooth phone tothe system, this becomes the activephone. For further information referto the phone menu.
However, in some cases theBluetooth phone has to be activatedby pressing the appropriate stationbutton on the audio or navigationunit.
Turning the ignition back on again,the last active phone is picked up bythe system.
143
Telephone
Bond another Bluetoothphone
Note: Before another Bluetoothphone can be bonded, the existingactive Bluetooth connection has tobe deactivated by the mobile phone.
Bond a new Bluetooth phone asdescribed in the requirements for aBluetooth connection.
Phones stored in the system areaccessible by using the phone list onthe audio or navigation unit.
Note: If six (five Bluetooth phonesfor cradle phone system) Bluetoothphones have been bonded, one ofthese has to be deleted in order tobond a new phone.
Cradle phone
With your phone fitted in the mobilephone cradle this does notautomatically become the activephone.
In these cases refer to Changingthe active phone in theappropriate section which describesthe system fitted to your vehicle.
BLUETOOTH SETUP
Before you can use your telephonewith your vehicle it must be bondedto the vehicle telephone system.
Handling of phones
A phone can be connected to thevehicle system by using either acradle connection or a Bluetoothconnection.
On vehicles with a mobile phonecradle, up to five Bluetooth phonescan be bonded to the vehicle system.
On vehicles without a mobile phonecradle, up to six Bluetooth phonescan be bonded to the vehicle system.
Note: If there is an ongoing callwhen the phone in use is selected asthe new active phone, the call istransferred to the vehicle audiosystem.
Note: Even if connected to the carsystem, your phone can still be usedin the usual way.
Requirements for Bluetoothconnection
The following are required before aBluetooth phone connection can bemade.
1. The Bluetooth feature must beactivated on the phone and onthe audio unit. For additionalinformation, refer to your phoneuser guide
2. The private mode must not beactivated on the Bluetooth phone.
3. Search for audio device.4. Select Ford Audio.5. The Bluetooth PIN number 0000
must be entered on the phonekeypad.
144
Telephone
Note: A phone call will bedisconnected if the audio/navigationsystem is switched off. If the ignitionkey is turned to the off position thephone call will remain in progress.
Compatibility of phones
CAUTION
As no common agreementexists, mobile phone
manufacturers are able to implementa variety of profiles in their Bluetoothdevices. Because of this, anincompatibility can occur betweenthe phone and hands-free system,which in some cases may significantlydegrade the system performance.To avoid this situation, onlyrecommended phones should beused. Please contact your dealer formore details regarding the currentcompatibility list.
Phones with Symbianoperating system
Note: Certain phones require aspecial file to be installed to enablefull phonebook access via Bluetooth.This is referred to as a SIS file and willbe available via the Ford website.Please consult your dealer for fulldetails.
TELEPHONE CONTROLS
Ending or rejecting calls
By pressing one of several functionbuttons on the audio or navigationunit (example: AM/FM,CD/AUX)active calls can be ended or incomingcalls can be rejected.
Remote control
One of several different types ofremote control may be fitted to yourvehicle:
Voice and mode button
1
2
E87661
Voice button1
Mode button2
Incoming calls can be accepted bypressing the MODE button once orended by pressing twice.
145
Telephone
Voice and accept/reject button
1 2
E87662
Voice button1
Accept/Reject button2
The VOICE button is used to activateor switch off the Voice control.
On vehicles with an accept/rejectbutton, phone calls can be acceptedand rejected by pressing theappropriate button.
Note: Some audio units have theaccept/reject buttons on the frontbezel. These operate in the sameway.
Mode button on the steeringwheel
E87663
Mode button only
E87664
On vehicles without a VOICE button,the MODE button on the remotecontrol is used to activate or switchoff the voice control.
Note: You will not be able to use theMODE button to activate the voicecontrol during an incoming or activecall.
You will not be able to use the MODEbutton to control the audio system.
USING THE TELEPHONE- VEHICLES WITHOUT:NAVIGATION SYSTEM
This chapter describes the phonefunctions of the audio unit.
Note: Refer to your audio guide fordetails of the controls.
An active phone must be present.
Even if connected to the audio unit,your phone can still be used in theusual way.
Note: You can exit the phone menuby pressing any source button CD,AM/FM or AUX.
146
Telephone
Making a call
Dialling a number
You can access your phone addressbook either with the phone dockedin the cradle or via Bluetooth. Theentries will appear in the audio unitdisplay.
1. Press the PHONE or the callaccept button.
2. Press the MENU button.
3. Keep pressing the MENU buttonuntil PHONEBOOK appears.
4. Press the seek buttons to selectthe desired phone number.
Note: Press and hold the seekbutton to skip to the next letter in thealphabet.
5. Press the PHONE or the callaccept button to dial the selectedphone number.
If you have an audio unit with atelephone keypad (buttons 0-9, * and#), you can also direct dial by enteringthe number on the radio display viathe keypad and pressing the callaccept button:
1. Press the call accept button.
2. Dial the number using thetelephone keypad on the audiounit.
3. Press the call accept button.
Note: If you enter an incorrect digitwhilst entering a phone number,press the seek down button to erasethe last digit. A long press will erasethe complete string of digits.
Press and hold 0 to enter a + digit.
Ending a call
Calls can be ended by either:
• pressing one of the followingbuttons on the audio unit:PHONE, CD, AM/FM orON/OFF
• pressing the MODE button onthe remote control
• pressing the call reject button.
Note: If you have an audio unit witha telephone keypad you can end acall only with the call reject button.
Redialling a number
1. Press the PHONE or the callaccept button.
2. Press the MENU button.
3. Select the CALL OUT list or theCALL IN list.
Note: If the active phone does notprovide a call out list, the lastoutgoing call number/entry isdisplayed.
4. Press the seek button on theaudio unit.
5. Press the PHONE or the callaccept button to dial the desiredphone number.
Redialling the last diallednumber
Note: This applies to only audio unitswith a telephone keypad
1. Press the call accept button.
147
Telephone
2. Press the call accept button againto display the last dialled number.
3. Press the call accept button athird time to dial the number.
Receiving an incoming call
Accepting an incoming call
Incoming calls can be accepted byeither:
• pressing the PHONE button• pressing the MODE button on
the remote control• pressing the call accept button.
Rejecting an incoming call
Incoming calls can be rejected byeither:
• pressing the call reject button• pressing the CD button• pressing the AM/FM button.
Note: If you have an audio unit witha telephone keypad you can onlyreject a call with the call reject button.
Note: You cannot reject an incomingcall using the remote control.
Handling a secondincoming call
Note: The second incoming callfunction must be activated in yourphone.
If there is an incoming call whilst thereis an ongoing call, a beep will beheard and you will have the option toend the active call and to accept theincoming call.
Accepting a second incomingcall
Second incoming calls can beaccepted by either:
• pressing the call accept button• pressing the MODE button on
the remote control• pressing the PHONE button.
Note: This will cancel the ongoingcall.
Rejecting a second incomingcall
Second incoming calls can berejected by pressing either:
• pressing the call reject button• pressing the CD button• pressing the AM/FM button.
Note: If you have an audio unit witha telephone keypad you can onlyreject a call with the call reject button.
Changing the active phone
Note: Phones must be bonded tothe system before they can be madeactive.
Using the station storagebutton
1. Press the PHONE button on theaudio unit.
2. Press the preset number required(using the station preset buttons1 - 6).
Note: This process is only for audiounits without a telephone keypad.
148
Telephone
Using the audio unit menu
1. Press the PHONE or call acceptbutton.
2. Press the MENU button on theaudio unit.
3. Select the ACTIVE PHONEoption on the audio unit.
4. Scroll through the different storedphones by using the seek buttonsto display the bonded phones.
5. Press the MENU button to selectthe phone which is to be theactive phone.
Note: After bonding a Bluetoothphone to the system, this becomesthe active phone.
Debonding a bonded phone
A bonded phone can be deletedfrom the system at any time, unlessa phone call is in progress.
1. Press the PHONE or call acceptbutton.
2. Press the MENU button on theaudio unit.
3. Select the DEBOND option onthe audio unit.
4. Scroll through the differentphones by using the seek buttonsand display the phone to bedebonded.
5. Press the MENU button to selectthe phone which is to bedebonded.
USING THE TELEPHONE- TRAVEL PILOT EX
This chapter describes the phonefunctions of the Navigation SystemTravelPilot EX.
Note: Refer to your NavigationSystem TravelPilot EX guide fordetails of the controls.
An active phone must be present.
Even if connected to the NavigationSystem TravelPilot EX, your phonecan still be used in the usual way.
Making a call
Dialling a number - cradlephone
Using the cradle phone allows you toaccess your mobile phone addressbook. The entries will appear in theTravelPilot EX display.
1. Press the PHONE button on theaudio unit.
2. Using the PHONEBOOK optionin the menu.
3. Choose one of the letter areas.
4. Turning the right rotary entrycontrol, select the desired phonenumber.
5. By pressing the INFO button thedetails of the phonebook entrycan be displayed.
6. Press the right rotary entry controlbutton.
149
Telephone
Dialling a number - Bluetoothphone
Using the Bluetooth phone, phonenumbers can be dialled using voicecontrol, refer to the Voice controlchapter.
Ending a call
Calls can be ended by either:
• pressing the reject button• pressing the MODE button on the
remote switch• pressing the off button on the
navigation system• pressing the right rotary entry
control button.
Redialling a number - cradlephone
1. Press the PHONE button on theaudio unit.
2. Press the MENU button.
3. Select the CALL OUT list, CALLIN list or REDIAL.
4. Press the PHONE button on theaudio unit to dial the desiredphone number.
Redialling a number -Bluetooth phone
1. Press the PHONE button on theaudio unit.
2. Press the MENU button.
3. Select REDIAL.
4. Press the PHONE button on theaudio unit to dial the phonenumber.
Handling an incoming call
Accepting an incoming call
Incoming calls can be accepted byeither:
• pressing the accept button• pressing the MODE button on the
remote control• pressing the PHONE button on
the audio unit• using the ACCEPT option in the
menu.
Rejecting an incoming call
Incoming calls can be rejected byeither:
• pressing the reject button• pressing one of the following
buttons on the audio unit: CD,AM/FM
• using the REJECT option in themenu.
Note: You cannot reject an incomingcall using the remote control MODEbutton.
Handling a secondincoming call
Note: The second incoming callfunction must be activated in yourphone.
If there is an incoming call, whilstthere is an ongoing call, a beep willbe heard and you will have the optionto end the active call and to acceptthe incoming call.
150
Telephone
Accepting a second incomingcall
Second incoming calls can beaccepted by either:
• Pressing the accept button.• Pressing the MODE button on the
remote control.• Pressing the PHONE button on
the audio unit.• Using the ACCEPT option in the
menu.
Note: This will cancel the ongoingcall.
Rejecting a second incomingcall
Second incoming calls can berejected by pressing either:
• The teject button• one of the following buttons on
the audio unit: CD, AM/FM.
Changing the active phone
Note: Phones must be bonded tothe system before they can be madeactive.
1. Press the PHONE button on theaudio unit.
2. Using the ACTIVE PHONEoption in the menu, select theactive phone from the list usingthe preset buttons.
Debonding a bonded phone
A bonded phone can be deletedfrom the system at any time, unlessa phone call is in progress.
1. Press the PHONE button on theaudio unit.
2. Select the DEBOND option in themenu.
3. Select the phone from the list byusing the preset buttons.
Note: After bonding a Bluetoothphone to the system, this becomesthe active phone.
However, in some cases theBluetooth phone has to be activatedby pressing the appropriate stationbutton on the audio or navigationunit.
151
Telephone
PRINCIPLE OFOPERATION
Voice recognition enables operationof the audio system without the needto divert your attention from the roadahead in order to change settings, orreceive feedback from the system.
Whenever you issue one of thedefined commands with the systemactive, the voice recognition systemconverts your command into acontrol signal for the audio system.Your inputs take the form ofdialogues or commands. You areguided through these dialogues byannouncements or questions.
Please familiarise yourself with thefunctions of the audio system beforeusing voice recognition.
Note: If the Bluetooth and voicecontrol is used for an extendedperiod of time when the vehicle isstationary, make sure that the engineis running to avoid draining thebattery.
Supported commands
The voice control system allows youto control the following vehiclefunctions:
• phone
• radio
• CD Player
• climate control
• navigation system.
Note: The voice control system islanguage specific. If you require thesystem to operate in anotherlanguage please consult your dealer.
System response
As you work through a voice sessionthe system will prompt you with abeep tone each time the system isready to proceed.
Do not try to give any commandsuntil the beep tone has been heard.The voice control system will repeateach spoken command back to you.
If you are not sure how to continuesay "HELP" for assistance or"CANCEL" if you do not wish tocontinue.
The "HELP" function provides only asubset of the available voicecommands. Detailed explanations ofall possible voice commands can befound on the following pages.
Voice commands
All voice commands should be givenusing a natural speaking voice, as ifspeaking to a passenger or on thephone. Your voice level should bedependant on the surrounding noiselevel inside or outside the vehicle butdo not shout.
Name tag
The name tag functionality cansupport the phone, audio andnavigation features by using the"STORE NAME" function.
152
Voice control
• Store up to 20 name tags perfunction.
• The average recording time foreach name tag is approximately2-3 seconds.
USING VOICE CONTROL
System operation
The order and content of the voicecontrols are given in the followinglists. The tables show the sequenceof user voice commands and systemresponses for each available function.
<> indicates a number or storedname tag to be inserted by the user.
Short cuts
There are a number of voicecommand short cuts available, whichallow you to control some vehiclefeatures without having to follow thecomplete command menu. Theseare:
• phone: "MOBILE NAME"1, "DIALNUMBER", "DIAL NAME" and"REDIAL"
• CD player: "DISC" and "TRACK"• climate control: "TEMPERATURE",
"FAN", "AUTO MODE","DEFROSTING/DEMISTING ON"and "DEFROSTING/DEMISTINGOFF"
• radio: "TUNE NAME"• navigation: "ZOOM" and "ROUTE
SETTING".
1) Only when the mobile phone isfitted with Bluetooth and voicecontrol
Start communicating with thesystem
Before you can start talking to thesystem you first have to press theVOICE or MODE button for eachoperation and wait until the systemanswers with a beep.
E87665
AUDIO UNIT COMMANDS
CD Player/CD Changer
You can choose a disc or trackdirectly by voice control.
153
Voice control
Overview The overview below shows theavailable voice commands foroperating your CD player. Thefollowing lists will give furtherinformation about the completecommand menu.
"CD"
"HELP"
"DISC"a
"TRACK"b
a) Can only be used with a CD changer.
b) Can be used as a shortcut.
Disc
If you have a CD changer you canchoose the disc number.
System answerUser saysSteps
"CD""CD"1
"DISC NUMBER PLEASE""DISC"a2
"DISC <number>""<a number between 1 and 6>"3
a) Can be used as a shortcut.
Track
You can also choose a track on yourCD directly.
System answerUser saysSteps
"CD""CD"1
154
Voice control
System answerUser saysSteps
"TRACK NUMBER PLEASE""TRACK"a2
"TRACK <number>""<a number between 1 and99>"
3
a) Can be used as a shortcut.
Radio
The radio voice commands supportthe functionality of the radio and allowyou to tune radio stations by voicecontrol.
Overview
The overview below shows theavailable voice commands foroperating your radio. The followinglists will give further information aboutthe complete command menu.
"RADIO"
"HELP"
"AM"
"FM"
"TUNE NAME"a
"DELETE NAME"
"DELETE DIRECTORY"
"PLAY DIRECTORY"
"STORE NAME"
a) Can be used as a shortcut.
Tune frequency
This function allows you to tune yourradio by voice commands.
155
Voice control
System answerUser saysSteps
"RADIO""RADIO"1
"FREQUENCY PLEASE""AM"2
"FREQUENCY PLEASE""FM"
"TUNE <frequency>""<frequency>"3
Store name
If you have tuned a radio station, youcan store it with a name in thedirectory.
System answerUser saysSteps
"RADIO""RADIO"1
"STORE NAME""STORE NAME"2"NAME PLEASE"
"REPEAT NAME PLEASE""<name>"3
"STORING NAME""<name>"4"<name> STORED"
Tune name
This function allows you to call up astored radio station.
System answerUser saysSteps
"RADIO""RADIO"1
"NAME PLEASE""TUNE NAME"a2
"TUNE <name>""<name>"3
a) Can be used as a shortcut.
156
Voice control
Delete name This function allows you to delete astored radio station.
System answerUser saysSteps
"RADIO""RADIO"1
"NAME PLEASE""DELETE NAME"2
"DELETE <name>""<name>"3"CONFIRM YES OR NO"
"DELETED""YES"4
"COMMAND CANCELLED""NO"
Play directory
This function allows you to let thesystem tell you all of the stored radiostations.
System answerUser saysSteps
"RADIO""RADIO"1
"PLAY <DIRECTORY>""PLAY DIRECTORY"2
Delete directory
This function allows you to delete allstored radio stations at once.
System answerUser saysSteps
"RADIO""RADIO"1
"DELETE DIRECTORY""DELETE DIRECTORY"2"CONFIRM YES OR NO"
"RADIO DIRECTORY DELETED""YES"3
"COMMAND CANCELLED""NO"
157
Voice control
TELEPHONE COMMANDS
Phone
Your phone system allows you tocreate an additional phonebook. Thestored entries can be dialled by voicecontrol. Phone numbers stored byusing voice control are stored on thevehicle system and not in yourphone.
Overview
The overview below shows theavailable voice commands of thephone system. The following lists willgive further information about thecomplete command menu.
"PHONE"
"HELP"
"MOBILE NAME"a, b
"DIAL NUMBER"a
"DIAL NAME"a
"DELETE NAME"
"DELETE DIRECTORY"
"PLAY DIRECTORY"
"STORE NAME"
"REDIAL"a
"ACCEPT CALLS"
"REJECT CALLS"
a) Can be used as a shortcut.
b) Only possible on mobiles which are connected by Bluetooth and fitted withvoice control and stored name tags.
158
Voice control
Create a phonebook
Store name
New entries can be stored with the"STORE NAME" command. Thisfeature can be used to dial a numberby calling up the name instead of thefull phone number.
System answerUser saysSteps
"PHONE""PHONE"1
"STORE NAME""STORE NAME"2"NAME PLEASE"
"REPEAT NAME PLEASE""<name>"3
"STORING NAME""<name>"4"<name> STORED""NUMBER PLEASE"
"<phone number>""<phone number>"5
"STORING NUMBER""STORE"6"<phone number>"
"NUMBER STORED"
Delete name
Stored names can also be deletedfrom the directory.
System answerUser saysSteps
"PHONE""PHONE"1
"NAME PLEASE""DELETE NAME"2
"DELETE <name>""<name>"3"CONFIRM YES OR NO"
"<name> DELETED""YES"4
"COMMAND CANCELLED""NO"
159
Voice control
Play directory Use this function to let the system tellyou all stored entries.
System answerUser saysSteps
"PHONE""PHONE"1
"PLAY DIRECTORY""PLAY DIRECTORY"2
Delete directory
This function allows you to delete allentries in one go.
System answerUser saysSteps
"PHONE""PHONE"1
"DELETE DIRECTORY""DELETE DIRECTORY"2"CONFIRM YES OR NO"
"PHONE DIRECTORYDELETED"
"YES"3
"COMMAND CANCELLED""NO"
Phone functions
Mobile name
This function allows you to accessphone numbers stored with a nametag in your mobile phone.
System answerUser saysSteps
"PHONE""PHONE"1
"MOBILE NAME" "<phonedependent dialogue>"
"MOBILE NAME"a, b2
a) Can be used as a shortcut.
160
Voice control
b) Only when the mobile phone is fitted with Bluetooth and voice control(dependant on the mobile phone).
Dial number
Phone numbers can be dialled aftergiving the name tag voice command.
System answerUser saysSteps
"PHONE""PHONE"1
"NUMBER PLEASE""DIAL NUMBER"a2
"<phone number>"<phone number>"3CONTINUE?"
"DIALLING""DIAL"4
"<repeat last part of number>"CORRECTION"CONTINUE?"
a) Can be used as a shortcut.
Dial name
Phone numbers can be dialled aftergiving the name tag voice command.
System answerUser saysSteps
"PHONE""PHONE"1
"NAME PLEASE""DIAL NAME"a2
"DIAL <name>""<name>"3"CONFIRM YES OR NO"
"DIALLING""YES"4
"COMMAND CANCELLED""NO"
a) Can be used as a shortcut.
161
Voice control
Redial This function allows you to redial thelast dialled phone number.
System answerUser saysSteps
"PHONE""PHONE"1
"REDIAL""REDIAL"a2"CONFIRM YES OR NO"
"DIALLING""YES"3
"COMMAND CANCELLED""NO"
a) Can be used as a shortcut.
DTMF (Tone dialling)
This function transfers spokennumbers into DTMF tones, i.e. tomake a remote enquiry to your homeanswering machine.
Note: DTMF can only be used duringan ongoing call. Press the VOICEbutton or the MODE button and waitfor the system prompt.
System answerUser saysSteps
"NUMBER PLEASE"1
"<numbers 1 to 9, zero, hash,star>"
2
Main settings
Accept and reject calls
Calls can be accepted or rejectedusing the Voice Control.
System answerUser saysSteps
"PHONE""PHONE"1
"ACCEPT CALLS""ACCEPT CALLS"2
162
Voice control
System answerUser saysSteps
"REJECT CALLS""REJECT CALLS"
NAVIGATION SYSTEMCOMMANDS
Please refer to your separateNavigation handbook for details ofthe command menus.
CLIMATE CONTROLCOMMANDS
Climate
The climate voice commandssupports the functionality of the fanspeed, temperature and modesettings. Not all functions areavailable on all vehicles.
Overview
The overview below shows theavailable voice commands foroperating your climate controlsystem. The following lists will givefurther information about thecomplete command menu.
"CLIMATE"
"HELP"
"FAN"a
"DEFROSTING/DEMISTING ON"a
"DEFROSTING/DEMISTING OFF"a
"TEMPERATURE"a
"AUTO MODE"a
a) Can be used as a shortcut. On vehicles fitted with an English languagemodule the "FAN" shortcut is not available.
163
Voice control
Fan This function allows you to adjust thefan speed.
System answerUser saysSteps
"CLIMATE""CLIMATE"1
"FAN SPEED PLEASE""‘FAN"a2
"FAN MINIMUM""MINIMUM"
3 "FAN <number>""<a number between 1 and 7>"
"FAN MAXIMUM""MAXIMUM"
a) Can be used as a shortcut. On vehicles fitted with an English languagemodule the "FAN" shortcut is not available.
Defrosting/Demisting
System answerUser saysSteps
"CLIMATE""CLIMATE"1
"DEFROSTING/DEMISTING ON""DEFROSTING/DEMISTING
ON"a
2"DEFROSTING/DEMISTING
OFF""DEFROSTING/DEMISTING
OFF"a
a) Can be used as a shortcut.
Temperature
This function allows you to adjust thetemperature.
System answerUser saysSteps
"CLIMATE""CLIMATE"1
"TEMPERATURE PLEASE""TEMPERATURE"a2
164
Voice control
System answerUser saysSteps
"TEMPERATURE MINIMUM""MINIMUM"
3 "TEMPERATURE <number>"
"<a number between 15 and29 °C with 0.5 increments>" or"<a number between 59 and
84 °F>"
"TEMPERATURE MAXIMUM""MAXIMUM"
a) Can be used as a shortcut.
Auto mode
System answerUser saysSteps
"CLIMATE""CLIMATE"1
"AUTO MODE""AUTO MODE"a2
a) Can be used as a shortcut. Can be deactivated by selecting a differenttemperature or fan speed.
165
Voice control
VEHICLE IDENTIFICATIONPLATE
E85610C
B
E D
A
Vehicle identification numberA
Gross vehicle weightB
Gross train weightC
Maximum front axle weightD
Maximum rear axle weightE
The vehicle identification number andmaximum weights are shown on aplate located on the lock side of thepassenger door aperture at thebottom.
VEHICLE IDENTIFICATIONNUMBER (VIN)
E87496
The vehicle identification number isstamped into the floor panel on theright-hand side, beside the front seat.It is also shown on the left-hand sideof the instrument panel.
ENGINE NUMBER
The engine number is stamped onthe engine block near the gearboxon the front left-hand side facing theradiator.
166
Vehicle identification
WEIGHTS
Vehicle weight (kg)
Permiss-ible roof
rackweight
Permiss-ible gross
weight
PayloadEC kerbweight
Variant
25160544811571.25L Duratec
25160544911561.4L Duratec, 5-speedmanual transmission
25160544311621.4L Duratec, DurashiftEST
25160544611591.6L Duratec, 5-speedmanual transmission,without stability assist(ESP)
50160044111591.6L Duratec, 5-speedmanual transmission,with stability assist (ESP)
25163046611641.6L Duratec, automatictransmission
25164048311571.4L Duratorq-TDCi, 5-speed manual transmis-sion, without stabilityassist (ESP)
50163547811571.4L Duratorq-TDCi, 5-speed manual transmis-sion, with stability assist(ESP)
25164047811621.4L Duratorq-TDCi,Durashift EST
25167551011651.6L Duratorq-TDCi, 5-speed manual transmis-sion, without stabilityassist (ESP)
167
Technical specifications
Permiss-ible roof
rackweight
Permiss-ible gross
weight
PayloadEC kerbweight
Variant
50167050511651.6L Duratorq-TDCi, 5-speed manual transmis-sion, with stability assist(ESP)
168
Technical specifications
DIMENSIONS
Vehicle dimensions
E91022
D
E
C
A
B
169
Technical specifications
Dimension in mm(inches)
Dimension descriptionItem
4013 (158)Maximum lengthA
1950/19631
(76.8/77.31)Overall width including exterior mirrorsB
1512 - 1543 (59.5 -60.7)Overall height at EC kerb weightC
2486 (97.9)WheelbaseD
1477 - 1487 (58.1 -58.5)Front trackE
1435 - 1445 (56.5 -56.9)Rear trackE
1Vehicles with electric exterior mirrors
170
Technical specifications
Towing equipment dimensions
C
G
F
D
E
B
A
E90357
Dimension in mm(inches)
Dimension descriptionItem
133 (5.2)Bumper – end of tow ballA
12 (0.5)Attachment point – centre of tow ballB
171
Technical specifications
Dimension in mm(inches)
Dimension descriptionItem
869 (34.2)Wheel centre – centre of tow ballC
493 (19.4)Centre of tow ball – side memberD
986 (38.8)Inner side of side memberE
436 (17.2)Centre of tow ball - centre 1. attachment pointF
721 (28.4)Centre of tow ball - centre 2. attachmentpoint
G
172
Technical specifications
TYPE APPROVALS
Remote control
Note: We recommend that you usethe remote control only in thecountries listed.
If the type approval of your remotecontrol is inspected, refer to thefollowing table.
E72068
173
Type approvals
Engine immobiliser
If the type approval of your engineimmobiliser is inspected, refer to thefollowing tables.
E72069
174
Type approvals
E72070
175
Type approvals
ELECTROMAGNETICCOMPATIBILITY
WARNINGSYour vehicle has been testedand certified to European
legislations relating toelectromagnetic compatibility(2004/104/EC). It is your responsibilityto ensure that any equipment youhave fitted complies with applicablelocal legislations. Have anyequipment fitted by properly trainedtechnicians.
WARNINGSRadio frequency (RF) transmitterequipment (e.g. cellular
telephones, amateur radiotransmitters etc.) may only be fittedto your vehicle if they comply with theparameters shown in the table below.There are no special provisions orconditions for installations or use.
Do not mount any transceiver,microphones, speakers, or any
other item in the deployment path ofthe airbag system.
Do not fasten antenna cablesto original vehicle wiring, fuel
pipes and brake pipes.
Keep antenna and powercables at least 100mm from any
electronic modules and airbags.
E85998
6
7
1 2 3 8
4
5
176
Appendices
Antenna PositionsMaximum output powerWatt (Peak RMS)
FrequencyBand MHz
3, 850 W1 – 30
2, 350 W30 – 54
1, 2, 3, 4, 550 W68 – 87.5
1, 2, 3, 4, 550 W142 – 176
1, 2, 3, 4, 550 W380 – 512
1, 2, 3, 4, 5 (61, 71)10 W (2 W1)806 – 940
210 W1200 – 1400
1, 2, 3, 4, 5 (61, 71)10 W (1 W1)1710 – 1885
1, 2, 3, 4, 5 (61, 71)10 W (1 W1)1885 – 2025
All positions0.1 W2400 – 25001Only for GSM/3G cellular phones, with a patch antenna installed inside of thefront windscreen.
Note: After the installation of RFtransmitters, check for disturbancesfrom and to all electrical equipmentin the vehicle, both in the standby andtransmit modes.
Check all electrical equipment:• with the ignition ON• with the engine running• during a road test at various
speeds.
Check that electromagnetic fieldsgenerated inside the vehicle cabin bythe transmitter installed do notexceed human exposure limitsspecified in EU directive 2004/40/EC.
TYPE APPROVALS
Bluetooth/voice recognitionsystem - declaration ofconformity
We, the party responsible forcompliance, declare under our soleresponsibility that the HandsetIntegration product RX-1C is inconformity with the provisions of thefollowing Council Directive:1999/5/EC. A copy of the Declarationof Conformity can be found at:
www.nokia.com/phones/declaration_of_conformity
177
Appendices
The Bluetooth word mark and logosare owned by the Bluetooth SIG, Inc.and any use of such marks by FordMotor Company is under license.Other trademarks and trade namesare those of their respective owners.Nokia Corporation Keilalahdentie 4,02150 Espoo, Finland
178
Appendices
AA/C
See: Climate control............................67About this handbook........................5ABS
See: Brakes..........................................92ABS driving hints
See: Hints on driving with ABS..........92Accessories
See: Parts and accessories.................5Adjusting the steering wheel.........36Adjusting the windscreen washer
jets...................................................40Air conditioning
See: Climate control............................67Air vents............................................67Alarm.................................................35Appendices....................................176Arming the alarm.............................35
Alarm......................................................35Automatic arming delay.....................35
Arming the engine immobiliser.....34Audio control...................................36
Mode......................................................37Seek.......................................................36Volume..................................................36
Audio unit commands..................153CD Player/CD Changer.....................153Radio....................................................155
Automatic climate control..............70Air distribution........................................71Blower....................................................71Recirculated air.....................................71Setting the temperature.....................70Switching the air conditioning on and
off.........................................................71Switching the automatic climate
control on and off.............................72Windscreen defrosting and
demisting............................................71
Automatic transmission......................Drive modes..........................................91Emergency park position release
lever....................................................91Hints on driving with an automatic
transmission.....................................90Selector lever positions......................89
Auxiliary heater................................72Diesel auxiliary heater (depending on
country).............................................72
BBattery care....................................127Bluetooth setup.............................144
Compatibility of phones....................145Handling of phones...........................144Requirements for Bluetooth
connection......................................144Bonnet lock
See: Opening and closing thebonnet..............................................112
Booster cablesSee: Using booster cables...............127
Booster cushions............................20Booster cushion...................................21Booster seat.........................................20
Brake and clutch fluid check.......120Brakes...............................................92
Principle of operation..........................92Bulb changing
See: Changing a bulb..........................47Bulb specification chart..................52
CCar wash
See: Cleaning the exterior................125Catalytic converter.........................85
Driving with a catalytic converter......85Parking..................................................86
179
Index
Changing a bulb..............................47Central high mounted stop lamp......50Front direction indicators....................48Front fog lamps....................................49Headlamp main and dipped
beam..................................................47Interior lamp..........................................50Luggage compartment lamp.............51Number plate lamp.............................50Reading lamps......................................51Rear lamps............................................49Side lamps............................................48Side repeaters......................................48
Changing a fuse............................106Changing a road wheel................129
Installing a road wheel.......................132Jacking and lifting points...................130Locking wheel nuts............................129Removing a road wheel....................131Spare wheel........................................129Vehicle jack.........................................129
Changing the remote controlbattery............................................30
Changing the wiper blades............41Checking the wiper blades...........40Child safety.......................................19Child safety locks............................22Child seat positioning......................21Child seats........................................19
Child restraints for different massgroups................................................19
Cigar lighter......................................79Cleaning the exterior....................125
Body paintwork preservation...........125Cleaning the chrome trim.................125Cleaning the headlamps...................125Cleaning the rear window................125
Cleaning the interior......................126Instrument cluster screens, LCD
screens, radio screens..................126Seat belts............................................126
Climate control................................67Principle of operation..........................67
Climate control commands.........163Climate.................................................163
Coded keys.....................................34Convenience features....................79Coolant check
See: Engine coolant check...............119
DDetachable tow ball........................99
Driving with a trailer.............................101Driving without a trailer......................102Inserting the tow ball arm.................100Maintenance.......................................102Removing the tow ball arm...............101Unlocking the tow ball arm
mechanism.....................................100Dimensions.....................................169
Towing equipment dimensions........171Vehicle dimensions............................169
Direction indicators.........................45Disabling the passenger
airbag..............................................27Disabling the passenger airbag.........28Enabling the passenger airbag.........28Fitting the passenger airbag
deactivation switch..........................27Disarming the alarm........................35Disarming the engine
immobiliser.....................................34Driving hints....................................103
EElectric exterior mirrors..................54
Electric folding mirrors........................54Mirror tilting positions..........................54
Electric windows.............................53To open the driver’s window
automatically.....................................53
180
Index
Electromagnetic compatibility.....176Engine compartment overview.........Engine coolant check....................119
Checking the coolant level................119Topping up the coolant.....................120
Engine immobiliser..........................34Principle of operation..........................34
Engine number..............................166Engine oil check.............................118
Checking the oil level.........................118Topping up the oil...............................119
Exterior mirrors................................53Convex mirrors....................................53Folding mirrors.....................................53
FFastening the seat belts................26Front fog lamps...............................43Front seat armrest..........................78
Adjusting the armrest..........................78Fuel and refuelling...........................85
Technical specifications......................87Fuel burning heater
See: Auxiliary heater............................72Fuel consumption
See: .......................................................87Fuel consumption...........................86Fuel cut-off switch.........................104
Vehicles with a Duratec engine.......104Fuel filler flap.....................................86Fuel quality............................................Fuse box locations........................108
Central fuse box.................................108Fuse labels......................................106Fuses...............................................106
GGauges.............................................56
Engine coolant temperaturegauge.................................................56
Fuel gauge............................................57Gearbox
See: Transmission...............................88General driving points...................103
Vehicles with a diesel engine...........103General information on radio
frequencies....................................29Glove box.........................................79
HHandbrake
See: Parking brake..............................93Hazard warning flashers................45Headlamp levelling..........................44
Recommended headlamp levellingswitch positions...............................44
Head restraints................................76Adjusting the head restraint...............77Removing the head restraint.............77
Heated seats....................................77Heated windows and mirrors........72
Heated exterior mirrors......................72Heated windows..................................72
HeatingSee: Climate control............................67
Hints on driving with ABS...............92
IIgnition switch..................................82
Ignition switch positions......................82Immobiliser
See: Engine immobiliser.....................34Information displays........................61
General information.............................61Information messages...................63
181
Index
Inspecting safety systemcomponents................................105Seat belts............................................105
Instruments......................................56Interior lamps...................................45
Courtesy lamp......................................45Reading lamps.....................................46
Interior mirror...................................55Introduction........................................5
JJump starting
See: Using booster cables...............127
KKeys and remote controls.............29
LLighting control................................42
Autolamps.............................................42Headlamp flasher................................43Home safe lighting..............................42Main/dipped beam..............................43Welcome lighting.................................42
Lighting.............................................42Load carriers
See: Roof racks and load carriers.....98Load carrying...................................98
General information.............................98
Locking and unlocking...................32Automatic relocking............................33Central locking.....................................32Double locking.....................................32Locking and unlocking
confirmation......................................32Locking and unlocking the doors with
the key...............................................32Locking and unlocking the doors with
the remote control..........................33Reprogramming the unlocking
function..............................................33Locks................................................32Luggage covers..............................98
MMaintenance....................................111
General information.............................111Technical specifications....................122
Manual climate control...................68Air distribution control.........................68Blower...................................................68Cooling the interior quickly.................70Cooling with outside air......................69Defrosting and demisting the
windscreen.......................................69Heating the interior quickly.................69Recirculated air....................................69Reducing interior air humidity............70Switching the air conditioning on and
off.......................................................69Temperature control...........................68Ventilation..............................................69
182
Index
Manual seats....................................74Adjusting the angle of the
seatback............................................75Adjusting the height of the driver’s
seat.....................................................75Folding the passenger seat
forwards............................................75Moving the seats backwards and
forwards............................................74Manual transmission.......................88
5-speed manual transmission...........88Durashift EST........................................88
Message centreSee: Information displays....................61
MirrorsSee: Heated windows and mirrors....72See: Windows and mirrors.................53
NNavigation system
commands...................................163
OOccupant protection......................23
Principle of operation..........................23Oil check
See: Engine oil check.........................118Opening and closing the
bonnet...........................................112Closing the bonnet.............................112Opening the bonnet...........................112
PParking aid........................................96
Principle of operation..........................96Parking aid
See: Using the parking aid.................96
Parking brake..................................93Applying the parking brake................93Parking on a hill....................................93Releasing the parking brake..............93
Parts and accessories......................5Look for the Ford logo on the
following parts ....................................6Now you can be sure that your Ford
parts are Ford parts...........................5Personalised settings.....................63
Audible warnings.................................63Audio display........................................63Direction indicators..............................63Hazard warning flashers.....................63Language..............................................63Unlocking the doors with the remote
control................................................63Power steering fluid check..........120Programming the remote
control............................................29Re-programming the unlocking
function..............................................30
QQuick start..........................................8
RRear fog lamps................................44Rear seat armrest............................81
Activity console.....................................81Rear seats........................................76
Creating a level load floor...................76Folding the seatbacks down.............76
Rear window wiper andwashers..........................................39Intermittent wiping...............................39Reverse gear wipe..............................39Washer..................................................40
Refuelling..........................................86Remote control battery
183
Index
See: Changing the remote controlbattery...............................................30
Remote control programmingSee: Programming the remote
control................................................29Removing a headlamp...................46Repairing minor paint
damage........................................126Roof racks and load carriers.........98
Roof rack...............................................98Running-in......................................103
Brakes and clutch..............................103Engine..................................................103Tyres.....................................................103
SSafety precautions..........................85Seat belt height adjustment..........26Seats.................................................74Sitting in the correct position.........74Snow chains
See: Using snow chains....................139Stability control................................94
Principle of operation..........................94Stability control
See: Using stability control.................95Starter switch
See: Ignition switch..............................82Starting a diesel engine..................84
Cold or hot engine...............................84Starting a petrol engine..................82
Cold or hot engine...............................82Engine idle speed after starting........83Flooded engine....................................83
Starting the engine.........................82General information.............................82
Status after a collision...................104Steering wheel................................36Storage compartments.................79
Storage box..........................................79Storage pockets..................................80
Sunroof.............................................73Sun visors.........................................79Switching off the engine................84
Vehicles with a turbocharger.............84Symbols glossary..............................5
Symbols in this handbook....................5Symbols on your vehicle.......................5
TTechnical specifications................167Telephone commands.................158
Create a phonebook.........................159Main settings......................................162Phone...................................................158Phone functions.................................160
Telephone controls.......................145Ending or rejecting calls....................145Remote control..................................145
Telephone setup...........................142Bond another Bluetooth phone......144Making a phone an active phone.....143Phonebook.........................................143Phonebook categories.....................143Placing your phone in the cradle.....142Requirements for cradle
connection......................................142Telephone.......................................142
General information...........................142Telephone
See: Using the telephone.......................See: Using the telephone.......................
Towing a trailer................................99Steep gradients...................................99
Towing points.................................109Front towing eye................................109
Towing the vehicle on fourwheels...........................................109All vehicles...........................................109Vehicles with a Durashift EST...........109Vehicles with an automatic
transmission.....................................110
184
Index
Towing..............................................99Transmission....................................88Type approvals.......................173, 177Tyre care.........................................139Tyre repair kit..................................133
Checking the tyre pressure.............138General information...........................134Inflating the tyre..................................135Using the tyre repair kit.....................134
TyresSee: Wheels and tyres......................129
UUsing booster cables....................127
To connect the booster cables.......127To start the engine.............................128
Using seat belts duringpregnancy......................................27
Using snow chains........................139Using stability control......................95Using the parking aid......................96
Manoeuvring with the parkingaid.......................................................97
Switching the parking aid on andoff.......................................................96
Using the telephone............................Changing the active phone...............151Debonding a bonded phone............151Handling an incoming call.................150Handling a second incoming call.....150Making a call.......................................149
Using voice control.......................153System operation..............................153
Using winter tyres..........................139
VVehicle battery...............................127Vehicle care....................................125Vehicle identification number
(VIN)...............................................166
Vehicle identification plate............166Vehicle identification......................166Vehicle recovery............................109Ventilation
See: Climate control............................67Vents
See: Air vents........................................67VIN
See: Vehicle identification number(VIN)..................................................166
Voice control..................................152Principle of operation........................152
WWarning lamps and indicators.......57
ABS warning lamp...............................57Airbag warning lamp...........................57Brake system warning lamp..............57Direction indicator................................58Door open warning lamp...................58Engine warning lamp..........................58Front fog lamp indicator.....................58Frost warning lamp..............................58Glow plug indicator.............................58Headlamp indicator.............................58Ignition warning lamp..........................58Low fuel level warning lamp...............58Main beam indicator...........................59Oil pressure warning lamp.................59Overdrive indicator..............................59Power steering warning lamp...........59Powertrain warning lamp...................59Rear fog lamp indicator......................60Stability control (ESP) warning
lamp...................................................60Washer fluid check........................121
Washer jets..........................................121Washers
See: Wipers and washers..................38Washing
See: Cleaning the exterior................125
185
Index
Weights...........................................167Wheels and tyres..........................129
General information...........................129Technical specifications....................140
Windows and mirrors.....................53Windscreen washers.....................39Windscreen wipers.........................38
Autowipers...........................................38Intermittent wiping...............................38
Winter tyresSee: Using winter tyres.....................139
Wipers and washers.......................38
186
Index
Feel the difference
8S6J-19A321-BDA(C
G3441en)