Forage Harvester · Forage Harvester ~ ~ .[Q1 ~ (g). ~ J . I . W . SERVICE PARTS MANUAL . l!J . Mr. Dealer: When ordering service parts, specify the correct part number, full description,

Form No.

902734 .

~ Forage Harvester ~

~ .[Q1

~ (g).

~

J I W

SERVICE PARTS MANUAL l!J

Mr. Dealer:

When ordering service parts, specify the correct part number, full description, quantity required, the unit model number and serial number.

The model number and serial number for this unit are on a decal located on the Main Frame below the right Quickswitch Yoke.

"Right" and "Left" are determined from a l?osit~on standing behind the unit and facing toward the dlrectlOn of travel. From this position, the Bevel Gearbox and Drive Line are on the "Left" side.

GEHL Company reserves the right to make changes or improvements in the design or construction of any part of the unit without incurring the obligation to install such changes on any unit previously delivered.

NOTE: On original Tire replacement, Company policy prohibits the sale of replacement tires for all original GEHL machinery. Replacement Wheel Sets are available and tire size information is calledout with the Wheel Sets to facilitate replacement tire selection. ALL REPLACEMENT TIRES MUST BE PURCHASED LOCALLY.

NOTE: Common hardware, such as nuts, cap screws, etc. are listed in the parts list but NOT illustrated. Hardware listed, is for mounting

purposes and NOT included when the pC'rt is ordered for replacement. For the part numbers of common hardware, refer to the attaching hardware table located inside the back cover.

Standard hardware torques appear in a chart at the end of the manual.

Unless otherwise specified, all Cap Screws or Bolts are Grade 5, cadmium or zinc plated; Hexagon Nuts for Grade 5 Cap Screws or Bolts are Grade B; Hexagon Nuts for other Cap Screws or Bolts are Grade A.

The following abbreviations are used in this manual:

CB - Carriage Bolt HHCS - Hexagon Head Cap Screw HTFS - Hexagon Thread Fastening Screw PB - Plow Bolt RHMS - Round Head Machine Screw SHSS - Socket Head Set Screw SQHSS - Square Head Set Screw HJN - Hexagon Jam Nut HLN - Hexagon Lock Nut HN - Hexagon Nut SN - Slotted Nut WN - Wing Nut LW - Lock Washer PW - Plain Washer T - Tooth PTO - Power Take Off

TABLE OF CONTENTS

Page Introduction ........................................................................ Inside Front Cover Table of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 1

Guards, Covers, Shields & Troughs ................................................................ 10-11

Hydraulics .................................................... 30

Decal Locations ................................................................................... 2-3 Main Frame ........................................................................................ 4-5 Implement Drive Line .............................................................................. 6-7 Cutting Mechanism ................................................................................ 8-9

Deflector & Cap ................................................................................. " 12 Blower ...................... , ................... , .............................................. 13-15

Blower Drive .................................................................................. " 13 Blower Housing & Fan ................................................................•........ 14-15

Spinner & Drive ................................................................................. 16-17 Feed Rolls ...................................................................................... 18-21

Rolls, Sheets & Roll Drives ..................................................................... 18-19 Stationary.. & Supporting Parts .................................................................. 20-21

Electrical Controls ... '.' .......................................................................... 22-23 3-Switch 'Control Box .............................................................................. 24 Bevel Gearbox. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 25 Length-of-Cut Transmission ....................................................................... 26-27 Knife Sharpener ................................................................................. 28-30

Main Unit .................................................................................... 28-29 P •••••••••••••••••••••••••••••••••

Universal Drives ................................................................................. 31-33

Standard Hardware Torque Specifications .............................................. Inside Back Cover Attaching Hardware Table ............................................................ Inside Back Cover

Upper Feed Roll Drive ........................................................................... 31 Lower Feed Roll Drive ........................................................................... 31 Tubular Main Drive .............................................................................. 32 1-3/8" Telescoping Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 32 1-3/4" Telescoping Drive .......................................................................... 33 1-3/4" PTO Drawbar Extension ................................. , ................................. 33

Hitchjack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 34 Toolbox Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 35 Options ..................................................... ; .. ,................................. 36-37

Tandem Axles & Wheel Sets ...................................................................... 36 Single Wheel Axle Set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 37 Wheel Sets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 37

Accessories ...................................................................................... 38-44 Horizontal Deflector Extension Kits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 38 I-Ft Vertical Deflector Extension Kit ............................................................... 39 2-Ft Vertical Deflector Extension Kit ............................................................... 39 Tripod Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • . . . . .. 40 Hydraulic Controls Kit ........................................................................... 41 Deflector Tripod Extension ....................................................................... 41 Electric Tractor Extension Controls ................................................................ 42 Auxiliary Lift Spring Kit ......................................................................... 42 Hydraulic Deflector Cylinder & Hose Kit ........................................................... 42 Deflector Liner Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 43 Knife Torque Wrench ............................................................................ 43 Electric Remote 3-Switch Control Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 43 Length-of-Cut Gear Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 43 I" Slotted Silage Screen Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 44 Square Hole Screens ............................................................................. 44 Wet Crop Deflector Kit ........................................................................... 44

Numerical Index ................................................................................. 45-48

CB1250 - DECAL LOCATION

DECAL LOCATIONS Decal Locations are shown to assist in application of new decals in the event of damage to the Decal or refinishing of the machine . Check listing for information and the illustrations for their location.

Surfaces MUST be free from dirt. dust . grease and other foreign material before applying the new Decal. To apply. remove the smaller portion of the decal backing paper and apply this part of the exposed adhesive backing to the clean surface while maintaining proper position and alignment. Peel the other portion of the backing paper off slowly while applying hand pressure to smooth out Decal surface. .

NOTE: Discard Decals NOT required for this machine. Always order Decals by set number. DO NOT order Decals separately.

A WARNING: Always Observe Safety Rules Shown on Decals. If Decals become damaged, or if unit is repainted, replace

Decals.

NOTICE

Order paint for refinishing machines from this list:

901225 One Gallon Blaze Paint 901226 One Gallon Maize Paint 610239 6 (12 oz.) Cans Blaze Spray Paint 610240 6 (12 oz.) Cans Maize Spray Paint

The Decal Set Number for the CB J250 is 07 J850. The Set includes the following Decals:

1 -071718 WARNING - Rotating Guard 2 - 072148 DANGER - Avoid Electrical Contact 3 - 069273 Decal ~ Hitch Clip Set-up 4 - 065771 Decal - Shear Bolts (2 Places) 5 - 061187 Decal - Grease Fitting Symbol (7 Places) 6 - 071712 CAUTION - General Safety 7 - 071713 CAUTION - Read Operator's Manual 8 - 061202 GEHL 19 x 4 9 - 065232 Decal - RNF (Shift Indicator)

10 - 072058 CAUTION - Close or Replace Guard (4 Places)

11 - 071837 1250 (Vertical) 12 - 072150 WARNING - Keep Hands Out (2 Places) 13 - 060150 Decal - NO Step 14 - 072159 DANGER - Rotating Component

(3* Places) 15 - 062836 Decal - Spiral Symbol 16 - 062843 Decal - Keep RPM Up in Chute 17 - 067493 Red Reflector Strip (2 Places) 18 - 061204 GEHL 30 x 6 19 - 071834 1250 (Horizontal) 20 - 055375 Decal - Keep Tightened Down 21 - 069272 Decal - ' Cover Latches 22 - 067899 Decal - Tractor Horsepower Restriction 23 - 071576 Decal - Cutterbar Adjustment 24 - 065269 Decal - Knife Sharpener Operation

2

25 - 072257 WARNING - Remove PTO 26 - 072279 WARNING - Wear Goggles 27 - 058392 Decal - Shutoff Valve 28 - 056470 Decal - Attachment Drive Sprocket 29 - 071859 Decal - Wiring Diagram 30 - 062899 Decal - Length-of-Cut Chart 31 - 069469 Decal - Lift/Sharpener 32 - 071662 Decal - Prevent Overloads - Reverse at Idle 33 - 071860 Decal - Switch Wiring 34 - 072885 WARNING - Drawbar Extension

(1-3/4 PTO Models Only)

* One 072159 Decal also on 2 ft Vertical Extension

_______________ CB1250 - DECAL LOCATION

3

CB1250 - MAIN FRAME _________________

1M PORTA NT: Order by Part Number - DO NOT use Illustration Reference \I umbers.

4

CB1250 - MAIN FRAME

Ref. Part No. Ref. Part No. No. No. Part Name Req. No. No. Part Name Req.

I 9H300t Lock Pin 2...................... 9 33 062553 Axle Extension Spacer - Outside . 2 H6094 Hose Clamp ................... 2 650767 HHCS 1/2 x 3/4 .............. 4

650453 HHCS 1/2 x 1-1/2 ............ 2 (4) 1/2 LW (2) 1/2 HLN 34 062673 Lift Crank .....................

3 H8353A Gatherer Idler Spacer ........... 4 (Includes (2) 062545 Plastic 4 D9117A Frame Washer ................. 1 Bearings) 5 B11201A Take.;up Control Screw .......... 1 35 062906 Bracket Reinforcement .......... 1

(2) 5/8 HN - (2) PW 650486 HHCS 5/16 x 3/4 ............. 2 6 B11245 Hair Pin Cotter ................ 2 (2) 5/16 HN - (2) LW - (4) PW 7 R13245 Control Cord Bracket ........... 1 36 063667 Lift Crank Arm ................ 1

650246 HHCS 1/4 x 1-1/4 ............ 1 650490 HHCS 3/8 xl .... ~ ........... 2 (1) 1/4 HLN (2)3/8 HN - (2) LW

8 041881 OilSeal ...............•....... 2 37 063668 Lift Crank Pin ................. 1 9 044777 Roll Pin 5/16 x 2 ............... 2 38 064519 PTO Bearing Housing - Front. ... 1

10 045026 Retaining Ring ................. 8 39 065251 Lift Cylinder Link .............. 1 11 046777t Quick-switch Pin ............... 2 40 065838 Drawbar Roller ................ 1 12 050270 Roll Pin 3/16 x 1-1/4 ........... 1 570014 Grease Fitting ................. 1 13 058778t Hitch Control Cord - 5/16 X 16' .. 1 41 065847 Indexer Lever .................. 1 14 060587t Hitch Pin 1..................•... 1 42 065850 Spring ........................ 15 061838 Lift Roller 4..................... 2 43 066696 Spacer ........................

570014 Grease Fitting ................. 2 44 068124 Shield Support ................. 1 650695 HHCS 5/8 x 3-1/2 ............ 2 45 068134 Shaft Bearing Support .......... 1

(2) 5/8 HN - (2) LW 46 069766 Hitch Plate .................... 1 16 061839 Lift Roller Journal 4............. 2 650744 HHCS 1/2 x4 ................ 17 061930 Hex. Tap Plain Bolt ............ 1 (8) 1/2 HN 18 062463 Drawbar Roller Pin 1............. 1 47 070483 Drawbar Clip - Upper ...........

650533 HHCS 3/8 x 1-1/2 2............ 1 650499 HHCS 5/8 x 5-1/2 ............ . (1) 3/8 HLN 650486 HHCS 5/8 x 6 ................ 2

19 062488 Bearing Retainer ............... 2 (4) 5/8 HN - (4) LW 650811 CB 1/2 x 1 ................... 4 48 070484 Drawbar Clip - Lower ........... 1

(4) 1/2 HN - (4) LW 49 070485 Drawbar Spacer ................ 1 20 062490 Retaining Ring 1................. 1 50 071117A Hitchjack ...................... 21 062491 Drive Shaft Sleeve 1.............. 1 51 071236 Spring (PTO Support) •......... 22 062511 Lift Tube ...................... 1 52 071307 Drawbar ...................... 1

570019 Grease Fitting ................. 2 53 071338 PTO Bearing Support ........... 1 650495 HHCS 1/2 x 1-1/4 ............ 2 650453 HHCS 1/2 x 1-1/2 ............ 4 650503 HHCS 1/2 x 2-1/2 ............ 2 (4) 1/2 HLN

(4) 1/2 HN - (4) LW 54 071449 Main Frame ................... 1 23 062531 Lift Spring .................... 1 650486 HHCS 5/16 x 3/4 ............. 2 24 062532 Lift Spring Nut ................ 1 650956 SQHSS 1/2 x 1-1/2 ........... 1 25 062533 Lift Bearing .................... 1 (2) 5/16 HN - (2) LW - (4) PW

054813 Grease Fitting ................. 1 (1) 1/2 HN 26 062539 Lift Adjustment Stud ........... 1 55 071663t Hitch Pole Pivot Pin ............ 1 27 062540 Lift Link 1...................... 2 655030 Cotterpin 1/2 x 2 .............. 28 062542 Lift Pin 2....................... 3 56 072256 Cylinder Pin .................... 29 062543 Lift Adjustment Block .......... 1 57 520098 Ball Bearing ................... 2

650416 HHCS 3/4 x 2-1/2 ............ 1 58 520099 Bearing Collar ................. 1 (1) 3/4 HN - (1) LW

30 062544 Lift Stop Bar .................. 1 t Stored in Harvester's Toolbox. 31 062545 Plastic Bearing ................. 2 A See the Hitchjack Assembly illustration for Jack 32 062546 Lift Crank Shaft ............... 1 Service Parts.

5

CB1250 - IMPLEMENT DRIVE LINE

40

) IMPORTANT: Order by Part Number - DO NOT use Illustration Reference Numbers .

. 22

27 ~ ~. ~\17

26 ~ 23

6

_____________ CB1250 - IMPLEMENT DRIVE LINE


1 9H300 Lock Pin ...................... 2 31 062783B Bevel Gearbox ................. 1 2 17H361 Safety Flange Washer ........... 1 650495 HHCS 1/2 x 1-1/4 ............ 4

-3 H6073F Clutch Cover .................. 1 (4) 1/2 LW - (3) PW 650741 HHCS 5/16 x 3-1/4 ........... 6 32 062824c Gear (22T) .....................

(6) 5/16 HN - (6) LW and 4 H6075 Clutch Spring .................. 062829c Gear (26T) ..................... 5 D9130 Idler Sprocket (17T) ............ or

650644 HHCS 1/2 x 3 ................ 062890 Gear (28T) ..................... (I) 1/2 HN - (4) PW - (I) LW and (1) 5/8 PW 062891 Gear (20T) .....................

6 Bl1l62B Shim Washer .................. 4 33 062834 Chain (#60H) of 78 Links Including 7 M12361 Belt Support Spring ............ 1 One (500160) Connector Link ... 8 041489 Chain (#50) of 97 Links Including 34 062911 t Chain (#60H) of 64 Links Including

One (500057) Connecting Link and Three (047801) Connector and One One (500058) Offset Link ...... 1 (047807) Offset Link ..........

9 042856 Clutch Hub .................... 1 35 0652520 Cutting Cylinder - Assembled .... 570002 Grease Fitting ................. 1 (9 Blade)

10 043020 Clutch Drive Hub .............. 1 36 065658 Idler Bracket ................... 1 11 043684 Ball Bearing ................... 1 650490 HHCS 3/8 xl ................ 4 12 051948 Retaining Ring ................. 1 (4)3/8 HN - (4) LW 13 052884 Sprocket (30T) ................. 1 37 068127A Tubular Drive Shaft w/Universal

650206 SHSS 5/16 x 1/2 .............. 1 Joint ......................... 655533 Woodruff Key 5/16 x 1 .,. ...... 1 (I) 1/2 LW

14 055021t Hose Clamp ................... I 38 068280 Clutch Dog .................... 061872 HTFS 5/16 x 3/4 ............. 1 39 069431E Length-of-Cut Transmission

IS 056468 Attachment Drive Sprocket (17T). I Assembled .................... I or 40 070613 Extension Spring ............... 2

056283A Attachment Drive Sprocket (20T). 41 071443 Idler yoke ..................... 1 16 056640 Retaining Ring ................. 42 071446 Yoke Strip ..................... 1 17 057557 Washer........................ 1 43 071447 Idler Yoke Key ................. 1 18 057617 Washer. ................. As Req'd. 44 071508 Idler Sprocket (1ST) ............ 1 19 059084 Adjustment Cover .............. 1 650572 HHCS 5/8 x 2-3/4 ............ 1

20 061872

059085 HTFS 5/16 x 3/4 .............

Adjustment Cover Gasket ....... 2 1

(1) 5/8 HN - (1) LW - (7) PW

21 060279A Universal Joint ................. 1 45 071743 Main Drive Shaft ............... 22 23 24 25

060979 061006 062225 062227

HHCS 1/2 x 1-1/4 ............. Joint Wire ..................... Idler Lock ..................... Guide Wire ....................

1 1 2 1 46

650542 071745

(Shaft includes part numbers 068127,071745 &071746)

HHCS 1/4 x 1/2 .............. Bolt Lock .....................

4 2

26 062499A

071691A

Universal Joint w/Sq. Shaft 1-3/8 PTO ....................

Universal Joint w/ Sq. Shaft 47

650542 071746

HHCS 1/4 x 1/2 .............. Flange Retainer ................

4 2

1-3/4 PTO .................... t Stored in Harvester's Toolbox. 27 062500A Universal Joint w/Sq. Tube A See the Universal Drive Joint illustrations for Univer

071692A 1-3/8 PTO ...........•........

Universal Joint w/Sq. Tube sal Joint and Shaft Service Parts.

B See the Bevel Gearbox Assembly illustration for 1-3/4 PTO .................... 1 Transmission Service Parts.

28 062614 Spinner Drive Sprocket (17T) .... I c Attached to back of Toolbox. 655533 Woodruff Key 5/16 x 1 ........ 1 0 See the Cutting Mechanism illustration for Cylinder 650212 SHSS 3/8 x 3/8 ............... 2 Service Parts.

29 062643 Retaining Ring ................. 1 E See the Length-of-Cut Transmission illustration for 30 062667 Clutch Dog Pin 5/8 x 1-1/2 ..... 1 Transmission Service Parts.

7

CB1250 - CUTTI G MECHANISM ______________

21 ~34

V 29

:7'31 /~~ 4~'PM/28 /~/.! 33'"if /// I 25 11

/~ 27 : 26

I I I I

1 IMPORTANT: Order by Part Number - DO I NOT use Illustration Reference Numbers.

",tV30

CB1250 - CUTTING MECHANISM


1 9H300 Lock Pin ...................... 2 20 068901 Shear Bar Nut ................. 1 2 046864 Cam Bolt ...................... 6 21 071287 Cutterbar ...................... I 3 046866 Screen Adjustment Cam ......... 6 22 071448 Shield Bracket - Front .......... 1

(6) 1/2 HN - (6) LW 650710 HHCS 5/8 x 2-1/4 ............ 2 4 046873 Washer ........................ 2 (2) 5/8 HN - (2) LW 5 061267 Knife Bolt ..................... 27 23 071482 Cutterbar Guide ................ 6 061840 Knife ....................... '.. 9 24 071486 Cutterbar Adjustment'Stud ...... 7 062597 Knife Head .................... 3 (2) 3/4 HJN - (2) PW 8 062601 Washer ........................ 27 25 071487 Slot Baffle - Left ............... 9 062602 SQHSS 1/2 x 1-1/4 ............ 18 26 071488 Pivot .........................

10 062603 Square Nut - 3/4 ............... 27 27 071495 V-Bolt .................... '..... 11 062604 Bearing Housing ............... 2 (2) 3/8 HN - (2) LW - (2) PW

570002 Grease Fitting ................. 2 28 071503 Plunger ....................... 650710 HHCS 5/8 x 2-1/4 ............ 6 650551 Cotterpin 3/32 x 3/4 ...........

(6) 5/8 HN - (6) LW ~9 071504 Plunger Guide ................. 12 062607 Scraper ....................... I (1) 3/4 HJN

650527 CB 1/2 x 1-1/4 ................ 2 30 071505 Push Rod Nut ................. 1 (2) 1/2 HN - (2) PW - (2) LW 31 071507 Belleville Washer ............... 10

13 062774 Cylinder Tie ................... 1 32 071569 Cutterbar Adjustment Rod ...... 1 061872 HTFS 5/16 x 3/4 ............. 4 650490 HHCS 3/8 xl ................. 2

14 062844 Cylinder Cover ................. 1 650527 CB 1/2 x 1-1/4 ................ 1 15 062870 Knife Set-up Bar ............... I (1) 1/2 HN - (I) PW - (I) LW 16 065213 Cutterbar Slot Baffle ............ I (2) 3/8 LW 17 065252 Cylinder Assembled .............

(Cylinder includes part numbers 061267,061840,062597,062601, 062603, 065253 & 068740).

I 33 071773 V-Bolt ........................

655006 Cotterpin 1/8 xl .............. (2) 1/2 SN

1 2

18 065253 Cylinder Shaft ................. I 34 072082 Tapered Cap ................... 1 19 068740 Knife Head Key 7 fl6 x 3 ........ 2 35 520103 Ball Bearing ................... 2

9

36 ~

,~/32 f ~MPORTANT: Order by Part Number - DO NOT use Illustration Reference Numbers.

30

31

10

27

CB1250 - GUARDS, COVERS, SHIELDS & TROUGHS

Ref. Part No. Ref. Part No. No. 1\0. Part Name Req. No. No. Part Name Req.

I 9H300 Lock Pin ...................... 1 26 066641 Shield Support - Rear Upper. .... 2 044116 Latch ......................... 6 (2) 5/16 HN - (2) LW - (2) PW

650812 RHMS #1224 x 1/2 ............ 12 27 066642 Shield - Left Rear .............. 1(12) #1224 HN - (12) LW - (2) PW 061872 HTFS 5/16 x 3/4 ............... 33 047269 Slow-moving Vehicle Emblem 28 066643 Rear Shield - Left Upper ........ IBracket ........................ 1 650486 HHCS 5/16 x 3/4 ............. 4650754 CB 5/ 16 x 1 / 2 ................ 2 (4) 5/16 HN - (4) LW - (8) PW (2)5/16 Hl\ -(2) LW 29 066644 Rear Shield - Left Lower ........ I4 055021 Hose Clamp ................... 650486 HHCS 5/16 x 3/4 ............. 2650486 HHCS 5/16 x 3/4 ........... " (2) 5/16 HN - (2) LW (J ) 5/16 HN - (l) L W 30 068130 Shaft Cover .................... 1

5 055690 Latch Handle .................. 2 31 068132 Shield - Lower ................. I6 055691 La tch Spring ................... 2 32 068133 Hose Side Cover ............... I7 055692 Latch Clip ..................... 2 33 069087 Tunnel Cover .................. I8 059075 Vinyl Hose Clamp .............. I 34 069423 Hinge ......................... I 9 059272 Shear Bolt Holder .............. 2 650486 HHCS 5/16 x 3/4 ............. 4

IO 059971t Shear Bolt 3/8 x 1-3/4 .......... 4 (4) 5/16 HN - (4) LW 11 060258 Grommet ...................... 2 35 069424 Hinge ......................... I12 062493 Drive J oint Guard .............. 2 650448 HHCS 1/4 x 3/4 .............. 2

061872 HWHS 5/16 x 3/4 ............ 4 (2) 1/4 HN - (2) LW - (2) PW13 062594 Shield Support - Lower ......... 1 14 062642 Front Shield Support - Rear ..... 1 36 070516 Hose Top Cover ................ 1

(2) 5/16 HN - (2) LW 650486 HHCS 5/16 x 3/4 ............. 5 15 062782 Front Chute ................... 1 (5) 5/16 LW - (5) PW

650486 HHCS 5/16 x 3/4 ............. 4 37 071351 Left Shield .................... 1 (4) 5/16 HN - (4) LW - (2) PW 650486 HHCS 5/16 x 3/4 ............. 6

16 062798 Toolbox ....................... I (6) 5/16 HN - (6) LW 650835 HHCS 1/4 xl ................ 2 38 071354 Left Front Side Shield .......... I

(2) 1/4 HN - (2) LW - (4) PW 650486 HHCS 5/16 x 3/4 ............. 5 650486 HHCS 5/16 x 3/4 ............. 3 (5) 5/16 HN - (5) LW

(3) 5/16 HN - (3) LW - (3) PW 39 071355 Front Shield ................... I 17 062886 Spinner Shield Cover ........... 2 650486 HHCS 5/16 x 3/4 ............. 6

(2) 5/16 WN - (2) HLN (6) 5/16 HN - (4) PW - (6) LW 18 062887 Transmission Shield Support. .... I 40 071356 Shield - Right Rear ............. I

061872 HTFS 5/16 x 3/4 ............. 4 41 071357 Bottom Shield Bracket .......... 1 19 062898 Shield - Top Rear .. " .......... I 650487 HHCS 5/16 x I ............... 1 20 062900 Slot Cover ..................... I 650578 HHCS 5/16 x 5 ............... 2

650486 HHCS 5/16 x 3/4 .............. 2 (3) 5/16 HN - (3) PW - (3) LW (2) 5/16 HN - (2) LW 42 071358 Rear Shield ....................

21 062901 Tripod Slot Cover .............. I 43 071359 S pinner Drive Shield ............ 650486 HHCS 5/16 x 3/4 .............. . 4 061872 HTFS 5/16 x 3/4 ................ 3

(4) 5/16 HN - (4) LW 44 071366 Chute ......................... I 22 062907 Cylinder Drive Shield ........... 1 650486 HHCS 5/16 x 3/4 ............. 1

061872 HTFS 5/16 x 3/4 ................. 2 650687 CB 5/ 16 x 3/4 ................ 4 (2) 5/16 HN - (2) LW - (2) PW (5) 5/16 HN - (5) LW - (2) PW

23 065528 Feed Roll Shield ............... 1 45 071369 Chute Cover ................... I 650486 HHCS 5/16 x 3/4 ................ 4 46 071573 Feed Roll Shield - Right ........ 1

(4) 5/16 HN - (4) LW 47 071579 Shield Handle .................. I 24 066638 Shield Handle - Rear ........... 2 650448 HHCS 1/4 x 3/4 .............. 2 25 066640 Shield Hook - Rear ............. 2 (2) 1/4 HN - (I) PW - (2) LW

Stored in Harvester's Toolbox. t

11

CB1250 - DEFLECTOR & CAP

IMPORTANT: Order by Part Number - DO NOT use Illustration Reference Numbers. 3

B

8

Ref. Part No. No. No. Part Name Req.

I 6HI30 Cap Spacer .............. '" . .. 2 2 040860 Ludwig Clip .. . . . . . . . . . . . . . . . . . 4

650548 RHMS #lO24 x 1/2............ 4 (4)#lO24 HN -(4)#10 LW

3 056336t Cap Spring.................... 1 4 063680 C1eanout Extensin Cover . . . . . . . . I 5 065268 Deflector Cleanout Cover. . . . . . . . 1 6 070378 Deflector Cap. . . . . . . . . . . . . . . . . . I

650453 HHCS 1/2 x 1-1/2 ............ 2 (2) 1/2 HN - (2) LW - (2) PW

7 070393 Deflector Liner. . . . . . . . . . . . . . . . . 1 650541 PB 5/ 16 xl. . . . . . . . . . . . . . . . . . 6

(6) 5/16 HN - (6) LW - (6) PW 8 071326 Deflector. . . . . . . . . . . . . . . . . . . . . . I

650453 HHCS I/2x 1-1/2 ............ 2 650527 CB 1/2 x 1-1/4 ................ 4

(6) 1/2 HN - (6) LW - (6) PW

t Stored in Harvester's Toolbox.

. 12

CB1250 - BLOWER BLOWER DRIVE

--

IMPORTANT: Order by Part Number - DO NOT use Illustration Reference Numbers.

15 13

6

21

Ref. No.

Part No. Part Name

No. Req.

Ref. No.

Part No. Part Name

No. Reg.

1 2 3 4 5 6

7 8 9

10 11

12

H6075 Clutch Spring ................... 054174 Bearing Cap Shim (.005) .. As Req'd. 054175 . Bearing Cap Shim (.0075) . As Req'd. 054176 Bearing Cap Shim (.020) .. As Req'd. 055746 Shim Washer .................. 1 062252 Idler Spring .................... 1

650453 H H CS 1 /2 x 1-1/2 ............ 1 (1) 1/2 HLN

062665 Blower Sheave (15.20 Dia.) .. '" . 062666 Blower Clutch Hub ............. 062667 Clutch Dog Pin ................ 062668 Sheave Bearing Cap ............. 062671 Clutch Blower Sheave ...........

(Sheave includes part numbers H6075, 054174, 054175, 054176, 055746,062665,062666,062667,

062668, 070074, 520105 & 520188)

570002 Grease Fitting ................. 1 062804 Idler Support Rear ............ 1

650533 HHCS 3/8 x 1-1/2 ............ 2 (4) 3/8 HN - (4) LW - (4) PW

13

14 15 16

17 18 19 20

21 22 23 24

25 26 27

062805 Idler Support - Front .......... . 650650 HHCS 1/2 x 3-1/2 ........... .

(I) 1/2 HLN 062806 Idler Arm .................... . 062810 Idler Pivot. ................... . 062811 Idler Strap .................... .

650503 HHCS 1/2 x 2-1/2 .......... .. (1) 1/2 HLN

062812 Belt Idler Retainer Strap ....... . 062908 Powerband Belt ............... . 065059 Shim.................... As Req'd. 068117 Drive Sheave (10.30 Dia.) ....... 1

650453 HHCS 1/2 x 1-1/2 ............ 4 (4) 1/2 LW

068118 Shear Flange .................. . 068280 Clutch Dog ................... . 068734 Tapered Key 3/8 x2 .......... .. 069298 Idler Pulley (5" Dia.) ........... .

650498 HHCS 1/2 x6 ............... . (1) 1/2 HN - (I) LW - (10) PW

070074 BoH Lock ..................... 3 520 I 05 Ball Bearing ................ . . . I 520188 Ball Bearing .. . . . . . .. . .. .. .. .. . I

13

25

CB1250 - BLOWER BLOWER HOUSING & FAN

T· Order by Part l\ urn ber - DO IMPORTAN . . Reference Numbers.l\ OT use IllustratIOn

14

CB1250 - BLOWER


1 3H55A Washer ........................ 5 18 065373 Blower Channel - Front ......... 1 2 UlOllO Washer ........................ 3 650533 HHCS 3/8 x 1-1/2 ............ 2 3 041499 Ball Bearing ................... 1 (3) 3/8 HN - (3) LW - (3) PW 4

5

043178 Fan Adjustment Cover .......... (9) 5/16 WN

055447 Washer ........................

3

1

19 20 21

066681 066684 070170

Blower Arm - Front ............ Blower Arm - Rear ............. Fan Plate ......................

6 6 6

6 056338 Blower Channel Shim ........... 5 650527 CB 1/2 x 1-1/4 ................ 24 7 057617 Washer"........................ 2 (24) 1/2 HN - (24) LW 8 061809 Bearing Housing ............... 1 (24)7/16 PW

570023 Grease Fitting ................. 1 22 071329 Blower Fan .................... (4) 3/8 HN - (4) LW (Fan includes part numbers 062617

9 10

11 12 l3

14

15 16

Blower Disc ...................062617 062635 Blower Channel - Rear ..........

650533 H H CS 3/ 8 x 1-1 / 2 ............ (3) 3/8 HN - (3) LW - (3) PW

062643 Retaining Ring ................. 062659 Rim Sheet ..................... 062663 Toggle ........................

650895 HHCS 5/8 x 8 ................ (2) 1/2 HN (2) 5/8 HN

062680 Channel Extension - Front. ...... 650569 HHCS 1/2 x 1-3/4 ............

(4)3/8 HN - (4) LW (4) 1/2 HN - (4) LW

062835 Air Intake Grate ............... 065368 Bearing Housing - Front ........

570019 Grease Fitting ................. (4) 1/2 HLN

1 1 2

1 2

23 24

25

26

27

28

and 071330) 650532 HHCS 5/8 x 1-1/2 ............

(12) 5/8 HN - (12) LW 071330 Blower Paddle ................. 071331 Blower Shaft ...................

650494 HHCS 1/2 xl ................ (1) 1/2 LW

071332 Side Sheet - Rear ............... 650687 CB 5/16 x 3/4 ................

(2) 5/16 HN - (2) LW - (2) PW 071334 Side Sheet - Front ..............

650786 CB 3/8 x 1-1/4 ................ (2) 3/8 HN - (2) LW

071432 Blower Outlet .................. 650541 PB 5/16 x 1 .................. 650786 CB 3/8 x 1-1/4 ................

(3) 5 16 HN - (3) LW (4) 3 8 HN - (4) LW

072258 Spacer ........................

12

6 1 1

1 2

1 2

1 3 4

17 065369 Tapered Hardened Key 3/8 x 2-1/2 ........ " .........

29 30 31

520093 520098 520099

Bearing Lock Collar ............ Ball Bearing ................... Bearing Lock Collar ............

15

NNER & DRIVECB1250 - SPI hee _ DO

. Part Num .NT Order by Numbers.IMPORTA .. n Reference NOT. use lllustratlo

22 1~

y~

16

CB1250 - SPINNER & DRIVE

Ref. Part No. Ref. Part No. No. No. Part Name Req. No. "10. Part Name Req.

H193A Bearing Retainer ............... 1 31 062871 Foam Pad ..................... I 650790 CB 3/8 x 3/4 ................. 3 32 0638728 Nut ........................... 2 650704 CB 3/8 xl ................... 6 33 065230 Bearing Housing ............... 1

(6) 3/8 HN - (6) L W - (3) PW (3) HLN 570011 Grease Fitting ................. I 2 HI95A Bearing Retainer ............... 3 650860 CB 3/8 x 1-3/4 ................ 3

650704 CB 3/8 x I ................... 3 (3) 3/8 HN - (3) LW 650860 CB 3/8 x 1-3/4 ................ 3 34 065640 Baffle Liner .................... 1

(6) 3/8 HN - (6) LW 650486 HHCS 5/16 x 3/4 ............. 3 3 H8224 Drive Sprocket Spacer .......... (3) 5/16 HN - (3) LW - (6) PW 4 R13007C Transmission Cap .............. 35 065641 Spinner Pan ................... I

061872 HTFS 5/16 x 3/4 ............. 4 650486 HHCS 5/16 x 3/4 ............. 10 5 R13113 Bearing Cap Gasket. ............ 1 650545 HHCS 5/16 x 1-1/4 .....•..... 2 6 045818 Shim Washer (12 Gauge) ., As Req'd. (12) 5/16 HN - (12) LW 7 045819 Shim Washer (16 Gauge) .. As Req'd. 36 065642 Snub Bushing .................. 8 046145 Shim Washer ............ As Req'd. 37 065646 Spinner Rotor Plate ............ 9 046526 Plate .......................... 1 (Rotor Plate Only)

10 046673 Bellville Washer ................ 1 38 065647 Bearing Plate .................. II 046847 Clutch Facing .................. 2 650486 HHCS 5/16 x 3/4 ............. 4 12 046848 Needle Bearing ................. 1 (4) 5/16 HN - (4) LW 13 049371 Roll Pin 5/16 x 1-3/4 ........... 1 39 068190 Horizontal Spinner Shaft ........ 14 050270 Roll Pin 3fl6 x 1-1/4 ........... 3 40 068198 Slip Clutch Assembly ........... 15 053719 Ball Bearing ................... 4 (Slip Clutch includes part numbers 16 054333 Nut ........................... 1 046526,046673,046847,054333, 17 054559 Bevel Gear (14 T) ............... 2 068199 & 068200). 18 054586 Latch ......................... 2 41 068199 Hub ..........................

650448 HHCS 1/4 x 3/4 .............. 4 42 068200 Sprocket Assembly (36T) ........ (4) 1/4 HN - (4) PW - (4) LW (Includes (1) Needle Bearing

19 056272 Cover Lock Knob .............. 2 046848). 20 056273 Cover Lock Rod ............... 2 43 069869c 62 mm Bearing Retainer .........

655006 Cotterpin 1/8 x 1 ~ ............. 2 44 070105 Rotor Hub .................... 21 057586 Bearing Retainer ............... 1 45 070108 Verticle Driven Shaft ........... 22 059548 Hole Plug ..................... 2 46 070112c Clip Retainer .................. I 23 061843A Angle Snap-on Coupler ......... 2 071703 3/8 HLN TW ................. 3 24 061845A Straight Connector ............. 4 47 070116c Grease Cup .................... 1 25 061847 Bulkhead Adapter .............. 2 48 071321 Spinner Rotor Assembly ........ 1

570019 Grease Fitting ................. 2 (Spinner Rotor includes part no's. 26 061848 Bulkhead Adapter Nut .......... 2 062583,062585,065646 & 070105). 27 062569 Spinner Shaft Shield ............ 1 49 071361 S pinner Lid .................... 28 062583 ' Spinner Paddle ................. 6

650490 HHCS 3/8 xl ................ 12 650491 HHCS 3/8 x 1-1/4 ............ 6

(18) 3/8 HN - (18) LW A To repair a broken or damaged Grease Line, order 29 062585 Low Wiper .................... 6 Tubing Kit 065185. (Instructions for Grease Line re30 062586 Spinner Shaft Shield ............ 1 pair are included with the kit).

650486 HHCS 5/16 x 3/4 ............. 8 B Use Nut if self-threading holes are damaged. 061872 HTFS 5/16 x 3/4 ............. 4 c For Replacement, order Spinner Bottom Cap Kit

(6) 5/16 HN - (8) LW 071328.

17

CB1250 - FEED ROLLS ROLLS, SHEETS & ROLL DRIVES


18

CB1250 - FEED ROLLS


1 H6208 Universal .I oint Washer. ......... 2 18 069416 Sprocket (32T) ................. 2 054042 Washer ........................ 2 19 069443e Universal Joint w/Sq. Tube ...... 3 055494 Transmission Shim ....... As Req'd. 20 070870 Extension Spring ............... 4 062738 Sleeve Bearing ................. 2 21 070874 Clear Plastic Hose ..............

650744 HHCS 1;2 x 4 ................ 1 22 0712778 Lower Universal Drive .......... (1) 1/2 HN - (2) PW (Drive includes part numbers

5 .062775 Chain (#50) of 45 Links including 063567, 069443 &. 071278) one (500058) Offset Link and one 650733 HHCS 5jI6 x 2-1/2 .; ......... 2 (500057) Connector Link ...... 1 (1) 5jI6 HJ\ - (1) LW - (1) HLN

6 062777 Idler Bracket ................... 1 23 0712788 Universal Joint wi Sq. Shaft ..... 650490 HHCS 3/8 xl ................ 4 (2) 5/16 HLN

(4) 3/8 HN - (4) LW 24 071280c Upper Universal Drive .......... 7 062778

650786 Idler Bar ...................... CB 3/8 x 1-1/4 ................

I 2

(Drive includes part numbers 063567,071281 &071283)

(2) 3/8 HN - (2) PW - (2) LW 650448 HHCS 1/4 x 3/4 .............. 8 063567tA Shear Bolt 5/16 x 1-1/2 ......... 4 (1) 1/4 HN

(1) 5/16-18 HLN - (2) PW 650733 HHCS 5jI6 x 2-1/2 ........... 2 9 066369 Gate Lock Arm Bushing ......... 2 (2) 5/16 HN

10 069372 Side Plate - Right .............. 1 25 071281c Universal Joint wjSpline Tube ... 650486 HHCS 5/16 x 3/4 ............. 2 26 071283c Universal Joint w/Spline Shaft ... 650487 HHCS 5/16 xl ............... 5 (1) 5/16 HLN - (2) LW 650545 HHCS 5/16 x 1-1/4 ........... 1 27 071322 Idler Arm ..................... 2

(8) 5/16 HN - (8) LW - (5) PW 650569 HHCS 1/2 x 1-3/4 ............ 4 650533 HHCS 3/8 x 1-1/2 ............ 3 (6) 1/2 HN - (2) PW - (6) LW

(3) 3/8 HN - (3) LW 28 071324 Spacer ........................ 11 069378 Side Plate - Left ..... ; .......... 1 29 071325 Torsion Spring. " " ........... ,

650486 HHCS 5fl6 x 3/4 ............. 2 30 071559+0 Clutch Link .................... 650487 H H CS 5/16 x I ............... 5 31 500078 Chain (#50) of 59 Links including 650545 HHCS 5/16 x 1-1/4 ........... 1 one (500057) Connecting Link and

(8) 5/16 HN - (8) LW - (5) PW one (500058) Offset Link ...... 650533 HHCS 3/8 x 1-1/2 ............ 3

(3) 3/8 HN - (3) LW 12 069391 Lower Front Roll .............. + Stored in Harvester's Toolbox. I

650494 HHCSI/2 xl ................ A For Replacement of Shear Bolts, order only Kit (1) 1/2 LW 900014 (Containing 8 Shear Bolts).

13 069394 Lower Rear Roll ............... I 8 For Components, see Lower Feed Roll Drive 14 069400 Sprocket (29T) ................. 1 illustration. 15 069402 Sprocket (16T) ................. 2 c For Components, see Upper Feed Roll Drive 16 069408 Upper Rear Roll ............... 1 illustration. 17 069411 Upper Front Roll ............... 1 0 For Replacement order Kit 071734 containing (1)

650494 HHCS 1/2 xl ................ 1 071559 Clutch Link,(1 )071701 5( 16 HLN, (I ),1/4 PW (1) 1/2 LW and instruction to install.

19

CB1250 - FEED ROLLS STATIONARY & SUPPORTING PARTS

.. e

bv ar , ber - DOP t Num IMPORTA NT'.OrderReferenceJ Numbers. ~OTu~ IllustratIOn .

41

42

20

CB1250 - FEED ROLLS

Ref. Part No. Ref. Part No. No. No. Part Name Req. No. No. Part Name Reg.

1 9H363 Hub Bushing... .... .. . . . ... .. .. 2 31 069388 Arm Guide ................ . . .. 2 2 S16215 Bearing Retainer - Inside . . . . . . . . 5 32 069389 72 mm Flangette ............... 2

650704 CB 3/8 xl. .. . . . . . . . . . .. . . . .. 3 33 069399 Bearing Retainer - Double. . . . . . . 1 650786 CB 3/8 x 1-1/4................ 9 650790 CB 3/8 x 3/4 ................. 3 652053 CB 3/8 x 2 ................... 3 (3) 3/8 HN - (3) LW

(18) 3/8 HN - (3) PW - (12) LW 34 069403 Retainer Shim ................. 4 3 042657 Lift Spring .................... 2 35 069404 Bearing Support Plate - Right. . . . 1 4 042658 Spring Nut. .. . . . . .. . . . . . .. . . .. 2 650502 HHCS 1/2 x 2-1/4 ............ 2 5 047621 Bearing Retainer - Outside....... 6 (2) 1/2 HN - (2) LW 6 048028 Spacer ..............•......... 4 36 069406 Spacer. . . . . . . . . . . . . . . . . . . . . . . . 1

. 7 051525 Bearing Retainer - Inside. . . . . . . . I 37 069407 Bearing. . . . . . . . . . . . . . . . . . . . . . . 2 650488 HHCS 3/8 x 3/4.............. 3 5700 II Grease Fitting. . . . . . . . . . . . . . . .. 4

(3) 3/8 LW 650486 HHCS 5/16 x 3/4.... ..... .... 4 8 055582 Sleeve Spacer. . . . . . . . . . . . . . . . .. 3 (4) 5/16 LW 9 059075 Tubing Clamp ................. I 38 069414 Bearing Support - Left. . ... . . . . . I

650487 HHCS 5/16 xl. . . . . . . . . . . . . . . I 650502 HHCS I 2 x 2-1/4 ............ 2 (I) 5/16 HN - (1) LW - (I) PW (2) 1/2 HN - (2) LW

10 060186 Shim Washer ............ As Req'd. 39 069422 Side Sheet Cover. . . . . . . . . . . . . . . I II 061843A Angle Snap-on Coupler. .. ...... 7 650448 HHCSI/4x3/4 .............. 2 12 061845A Tube Connector. . . . . . . . . . . . . . . . 3 (2) 1/4 HN - (2) PW 13 061847 Bulkhead Ada pter . . . . . . . . . . . . . . 2 40 069425 Feed Roll Stabilizer. . . . . . . . . . . . . I

570019 Grease Fitting. . . . . . . . . . . . . . . . . 2 570002 Grease Fitting. . . . . . . . . . . . . . . . . 2 14 061848 Bulkhead Adapter Nut ......... , 3 41 069635 Arm Guide- Right. . . . . . . . . . . . . . 1 15 062738 Feed Roll Sleeve Bearing. . . . . . . . 6 650490 HHCS 3/8 x I ................ 2

650585 HHCSI/2x2 ................ 6 650491 HHCS 3/8 x 1-1/4 ............ 1 (6) 1/2 HN -(6) LW (3) 3/8 HN - (3) LW - (1) PW

16 062740 Stabilizer Strap.. .. . . . . . . . . . . .. 4 42 069636 Arm Guide - Left. . . . . . . . . . . . . . . I 17 062750 Feed Roll Bearing Sheet. . . . . . . .. 2 650490 HHCS 3/8 x I ................ 2 18 062753 Wear Sheet Spacer. .. . . .. . . .... 2 650491 HHCS 3/8 x 1-1/4 ............ 1 19 062754 Feed Roll Wear Sheet. . . . . . . . . . . 2 (3) 3/8 HN - (3) LW - (I) PW

061872 HTFS 5/16 x 3/4 ............. 6 43 070062 Roll Guide Plate - Left. . . . . . . . . . I 20 062756 Spring Pin 3/8 x 2.............. I 44 070069 Roll Guide Plate - Right ........ I 21 062776 Spring Spacer............ .. .. .. 2 45 071118 Spring Strap................... 4 22 065254 Cylinder Tie Baffle - Front ...... 1 46 071167 Roll Stop - Right Rear. . . . . . . . . . 1 23 065527 Side Sheet Tie ........ ~ .... " . . 1 650573 CB 5/16 x I .................. 2

650486 HHCS 5/16 x 3/4 ......... .. .. 5 (2) 5/16 HN - (2) LW - (2) PW 650545 HHCS 5/16 x 1-1/4 ........... 2 47 071169 Roll Stop - Left Rear....... .... 1

(7) 5/16 HN - (7) LW 650573 CB 5/ 16 x I .................. 2 650492 HHCS 3/8 x 2-1/2 ........... . (2) 5/16 HN - (2) LW - (2) PW

(2) 3/8 HN 48 071171 Guide Stop Plate - Front. . . . . . .. 2 24 065624 Right Angle Adapter. . . . . . . . . . . . I 650745 CB 5/16 x 1-1/4............... 2

570019 Grease Fitting................. 1 (2) 5/16 HN - (2) LW 25 066549 Take-up Bolt 5/8 x 5 ........... 2 49 071571 Shaft Shield.. ...... ........... 1 26 066612 Stalk Guide - Right. . . . . . . . . . . . . 1 652053 CB 3/8 x 2 .. ................. 3

27

650490 HHCS 3/8 x I ................ (2) 3/8 LW

066614 Stalk Guide - Left. . . . . . . . . . . . . .

2

1 50 51

(3) 3/8 PW 520153 Bearing Lock Collar. ......... .. 540022 Retaining Ring. . . . . . . . . . . . . . . ..

7 2

650491 HHCS 3/8 x 1-1/4 ............ 2 (2) 3/8 LW

28 067833 Bearing Housing ............... 2 A To repair a broken or damaged Grease Line, order 29 069370 Hardened Washer. . . . . . . . . . . . .. 2 Tubing Kit #065185. (Instructions for Grease Line re30 069387 Ball Bearing ................... 8 pair are included with Kit)

21

CB1250 - ELECTRICAL CONTROLS _____--;-,__---::--____ ". - ..........

.... . .... ,,/,.)

,//~"""""";.-::.~ /" ',;;::/ ~ /,' ~?.., -'........'...-..._ / / /..".../)..-J . 5

/,' ~" /"}r.~--?:" ." ..::;~ ,',;-- ,'\ 10

,,' ....~...- .. -- ~ , ~~ , "-~ ,,

, ," ,::;" , ,,' ,~... ... ~-IMPORTANT: Order by Part Number - DO

~~

/ ' ~?~, , / h~7NOT use Illustration Reference Numbers. // ..::;-?' /" (fjI

// /;' " " ~ 9l

,/' ~ , "'i ""5

,

,',.,' ~ / ' ::" ,'/ //P ,/ . "";"~,/ /

" :!. ..." ,,', ,

" ," /' "

,.:' .:,: " :

21

22

45

CB1250 - ELECTRICAL CONTROLS

Ref. Part No. Ref. Part 1\ o. No. No. Part Name Req. No. No. Part Name Relj.

1 13E24 Roll Pin 1/4 x 1-1/2 ............ 1 31 070466 Worm Bearing ................. 2 2 6H154 Shim Washer .................. 4 32 070467 Cap Motor Mount. ............. 1 3 H8365 Bearing Retainer ............... 2 33 070468 Spool ......................... 1

650758 CB 1/4 x 3/4 ................. 4 34 071053A 3-Switch Control Box - Assembled I (4) 1/4 HN - (4) L W 35 071077 Receptacle Clamp .............. 1

4 17H386 Take-up Angle ................. 1 (2) 5fl6 HLN 5 B11433A S-Hook ....................... 3 36 071078 Receptacle Bracket ............. I 6 RI3178 Bushing ....................... I 650487 HHCS 5/16 xl ............... 4 7 056061 Wire Clamp .......... ,. ........ 1 (4) 5/16 HN - (2) LW - (2) PW 8 058357 Spacer ........................ 2 37 071079 Universal Bushing .............. 1 9 058368 Bushing ....................... 2 38 0710808 Cap Control Motor ............. 1

10 058539 Pulley (1" Dia.) ................ 2 39 071082 Barrier Terminal Board ......... I 11 059050 Roll Pin - 3fl6 x Iljl6 ......... 1 650815 RHMS #1024 x 3/4 ............ 2 12 059053 Mounting Bracket .............. 2 (2) #1024 HN - (2) #10 LW

650663 HHCS 1/4 x 5/8 .............. 6 40 071083 Terminal Board Cover .......... I (6) 1/4 HN - (6) LW - (4) PW 650637 RHMS #1024 x 1-3/4 .......... 2

13 059074 Open-Closed - Bushing .......... 1 (2) #1024 HN - (2) WN - (2) #10 LW 14 059075 Vinyl Hose Clamp .............. 5 41 071084 Backing Plate .................. 1 15 059313 Actuator Mount. ............... 1 42 071085 Wiring Harness ........ ,. ....... 1

650486 HHCS 5fl6 x 3/4 ............. 1 43 071087 Shaft Coupler .................. I 650545 HHCS 5jl6 x 1-1/4 ........... I 650579 HHCS 3/8 x 1-3/4 ............ 2

(3) 5fl6 HN - (2) LW - (3) PW (2) 3/8 HN - (2) LW 650494 HHCS 1/2 xl ................ 3 44 071089 Worm Shaft ...................

(3) 1/2 HN - (3) LW - (3) PW 45 071090 Worm Control Assembled ....... 16 059321 Bushing ....................... (Worm Control includes part num17 060369 Actuator ...................... ber's 13E24, 6H154, H8365,

650503 HHCS 1/2 x 2-1/2 ............ 070454,070463,070466 & 650585 HHCS 1/2 x 2 ................ 071089)

(2) 1/2 HLN 650938 Woodruff Key 3/16 x 5/8 ...... I 18 060974 Cap Control Cable ............. I 650490 HHCS 3/8 xl ................ 4 19 063646 Shift Arm ..................... 1 (4) 3/8 HN - (4) LW - (4) PW

650203 SHSS 5/16 x 3/8 .............. I 46 071166 Tractor Plug Cap ............... 20 063649 Pivot Bracket .................. 1 47 071209 Gear Guard .................... 21 064238 yoke .......................... 1 48 071210 Belt Guard Angle ............... 22 064239 Yoke Pin ...................... 1 49 071234 Gear Motor Guard Assembled ... 23 068120 Shifter Link ................... I (Gear Motor Guard includes part

24 650553

069245 Cotterpin I /8 x 3/4 ............

Motor Cap .................... 1 1

numbers 071209,071210 & 071235)

25 070449 Deflector Pilot ................. 2 650486 HHCS 5/16 x 3/4 ............. 3 650585 HHCS 1/2 x 2 ................ 4 (3) 5/16 HLN

(4) 1/2 HLN 50 071235 Guard Plate ................... 26 070450 Deflector Clamp ................ 4 51 071336 Transmission Cable ............. 27 070452 Deflector Gear ................. 2 52 071574 Shift Indicator .................

650585 HHCS 1/2 x 2 ................ 4 650814 HHCS 5/16 x 4 ............... (4) 1/2 HLN (1) 5/16 HLN

28 070453 Support Channcl ............... 2 53 072199 Gear Motor .................... 650490 HHCS 3/8 xl ................ 2 650938 Woodruff Key 3/16 x 5/8 ......

(2) 3/8 HN - (2) LW - (2) PW 650495 HHCS 1/2 x 1-1/4 ............ 2 A For Components, see 3-Switch Control Box

(2) 1/2 HN - (2) LW - (2) PW illustration. 29 070454 Worm Mount .................. 8 For Cap Motor repairs, order (as required) 062354 30 070463 Deflector Worm ................ Shaft Repair Kit or 062359 Gear Repair Kit.

23

CB1250- 3-SWITCH CONTROL BOX

IMPORTANT: Order by Part Number - DO NOT use Illustration Reference 1\umbers.

1------- --- ---1 I I

.e TO T"-ACTQFI GROUND

I -7---="--'~v---""'----'--,

~o "Jolt'I fUSE : (i ,,,co,, ""'" I

I lr 10 TRACTOR I~VDCI I

I I I I __________ -1

I "-CONTROLI BOX

I I 3 2 WIRING

HARNESS1"------: /' I 1:» : .~.d I f~~ii~L- \~ I r-t+H+-h

5 3 L

TERMINAL -1J1]~~~~BLOCK ::

Ref. Part No. Ref. Part No. No. No. Part Name Req. No. "\0. Part Name Req.

071053 3~Switch Control Box - Assembled 8 071068 Switch Cap Plate ............... 1 Consists of: 650702 RHSMS #6 x 3/8 ..................... 3

9 071069 Fuse Holder ................... 1 10 071070 Ferrule Fuse ................... I II 071071 Back Plate ..................... 1

1 057781 Bushing ....................... 1 650702 RHSMS #6 x 3/8 ............. 3 2 059064 Yellow Cable .................................... 4 12 071072 Strain Relief Bushing ........... 1 3 059065 Red Cable ..................... 2 13 071073 Wiring Harness .............................. 1 4 059066 White Cable ................... 2 14 071257 Power Supply Wire ............. I 5 059299 Toggle Switch .................. 3 15 071736 Ground Wire .................................... I 6 060972 Toggle Guard .................. 1 16 071737 Switch Wire (Red) .............. 2 7 071054 Deflector Control Box .......... I 17 071738 Fuse Wire ..................... I

24

CB1250 - BEVEL GEARBOX

iMPORTANT: Order by Part Number - DO NOT use Illustration Reference Numbers.


062783 Transmission Assembled ......... 21 056640 Retaining Ring ................. 1 Consists of: 22 058889 Cylinder Drive Spacer ... . ....... I

1 C354 Shim Washer ... .. . .. .. . . As Req'd. 650214 SHSS 3/ 8 x 1/ 2 ............... 2 2 R13077 Transmission Shim ( .005) . . As Req'd. 23 059489 Shim Washer .......... . .. . .... 1 3 RI3078 Transmission Shim (.007) . . As Req'd. 24 062287 Bevel Gear ............ . ... , .... 2 4 R13079 Transmission Shim (.020) .. As Req'd. 25 062784 Transmission Housing ........... 1 5 041916 Bearing Lock Nut . ........... . . 1 26 062785 Output Shaft .................. . 1 6 041917 Lock Washer ....... . .. . ....... 1 27 062786 Drive Sprocket (18T) . .......... I 7 042158 Spacer .... . ... . .. . ....... . ... . I 28 062788 Oil Seal . .. . .............. . . .. , I 8 04281 I Cover . ...... . ................. I 29 062789 Thru Shaft ................. ... I

650491 HHCS 3/ 8 x 1-1 / 4 .. . ......... 4 655521 Tapered Key 3/ 8 x 2 ........... ]

(4) 3/ 8 LW 30 062790 Shaft Spacer . . ......... . ....... ]

9 042813 Transmission Shim (.005) .. As Req'd. 3] 06279] Retaining Ring ............... . . 2 IO 042814 Transmission Shim (.007) .. As Req'd. 32 062792 Shaft Spacer ...... . . . .. . . .. .... ]

II 042815 Transmission Shim (.020) .. As Req'd. 33 062793 Bearing Cone ......... .. ....... ]

12 043836 Bearing Cup . ...... .. ...... . ... 3 34 062794 Bearing Cup ... . .......... . .... ]

13 043837 Bearing Cone ... . . . ....... .. ... 3 35 062795 Bearing Cap ... " .... . .... ' .' .. . ]

]4 043838 Oil Seal ................... .. . . I 650491 HHCS 3/ 8 x 1-1 / 4 ............ 4 15 043841 Retaining Ring .... . ......... . . . 2 (4) 3/ 8 LW 16 045668 Relief Fitting ... ............... I 36 062796 Cover Gasket .. . . .. . . . .. . ..... . I 17 049367 Cap .... . ........ . ............. I 37 062797 Transmission Cover ............. ]

18 055281 Oil Seal . .......... .. .. . ....... I 650490 HHCS 3/ 8 x ] ................ 6 19 055284 O-Ring .. . ........ .. ........ .. .. I (6) 3/ 8 LW 20 055449 Shim Washer ......... .. . As Req'd. 38 660004 Pipe Plug . . . ....... . ... . . . . . .. .

25

CB1250 - LENGTH-OF-CUT TRANSMISSION _________

J.z.) 2 37

~&i1di~ 54';1

'~ ~~ 14 I; ------~ .

~- - ------- '1 3 ~ {j1J 38 f:lJ (jjtJGi /,.\--------. -- J'?,' 37 )I",.,~ .' , . 52 -6. ~O{ . 53 7/ I! 1_3~ ~---J-t?;'J~ 1IJ.------E34 \ 18 5 10 45

56 7 U~Cu 5 I r - 28 I ~<oS"" 6

30 ---. 32?,~~t> 1 I 't fj48~. 27 I &!..-39 44 !~I,.,I

I 24 11 35 '/j)~30-q: ~ I 49 36 '/ r;t(!J 21 , -- -- -- :::: jJ~~ <::>. 33 1 f I (~ -. -- B

, . / . t)~ 7 56 r~~ (). _ 42 28 22 10 15 ' / ~ _ 34

I ~ / Itb£ 46 j@}b01J(1tJ-- ~Q)ej 2~3.31 29 2 6 VIF tk~7 ~- (i ~r, '_ /~i756 9 11 6 ~ ---A

, 26 ----- -- ~~. '. J ,_ 55 .~ .'. 9 56 ---- -~. C ({f) /~/ ': 2

]0 a/; /.\ (7t.J

~~, 40E--. ..' JI\ i· 20

··.~~.O/ - .. l ". /---- A IMPORTANT: Order by Part Number - DO~J~ .. NOT use Illustration Reference l\' umbers.

----8~.II

/ --......... C T:l

-/_______. ---- D 57

26

CB1250 - LENGTH-Of-CUT TRANSMISSION


069431 Transmission Assembled ........ . Consists of:

1 3H55A Washer. ...................... . 2 H267 A Washer. ................. As Req'd. 3 H275 Bearing Retainer ............... -2

650573 CB 5jl6 xl.................. 3 (3) 5/16 HN - (3) LW

4 041881 Oil Seal....................... 1 5 042864 Washer. . . . . . . . . . . . . . . . . . . . . . .. 2 6 043690 Ball Bearing ...... . . . . . . . . . . . .. 5 7 043691 Ball Bearing ...... . . . . . . . . . . . .. 4 8 043692 Oil Seal . . . . . . . . . . . . . . . . . . . . . .. 2 9 043693 Oil Seal. . . . . . . . . . . . . . . . . . . . . .. 2

10 043694 Retaining Ring. . . . . . . . . . . . . . . . . 2 11 044110 Retaining Ring.. .. .. .. .. .. .. ... 5 12 045668 Relief Fitting .................. 1 13 048512 Retaining Ring.. .. .. .. .. .. .. .. . 1 14 049344 Cover Gasket.................. 1 15 049366 Gear (l5T).... . . . .... .. .. .. .. .. . 1

655533 Woodruff Key 5/ 16 xl. . . . . . . . 1 16 056249 Bearing ....................... 1 17 056282 Oil Seal . . . . . . . . . . . . . . . . . . . . . . . 1 18 056341 Spacer. . . . . . . . . . . . . . . . . . . . . . . . 1 19 056352 Ball Bearing . . . . . . . . . . . . . . . . . . . 1 20 059548 Plug .. .. .. .. . .. .. .. . .. .. .. . .. . 1 21 060154 Transmission Clutch. . . . . . . . . . . . 1 22 060160 Gear (29T). . . . . . . . . . . . . . . . . . . . . 1

(Includes (1) 060161 Bushing) 23 060161 Bushing. . . . . . . . . . . . . . . . . . . . . .. 2 24 060164 Shifter . . . . . . . . . . . . . . . . . . . . . . . . 1

(2) 1/2 PW 25 060167 Sprocket (20T) ................ .

(Includes (1) 060161 Bushing) 26 060170 Bearing Housing Gasket. . . . . . . .. 2 27 060171 Wheel Spacer. . . . . . . .. . . . . . . . . . 2 28 060172 Washer........................ 3 29 060173 Spacer.. . . . .. .. . . . . . ... . ...... 1 30 060175 Shifter Wheel. . . . . . . . . . . . . . . . . . 2

Ref. Part No. No. No. Part Name Reg.

31 060176 Washer. ................. As Req'd. 32 060180 Sprocket (12T) . . . . . . . . . . . . . . . . . 1 33 060183 Gear (29T). . . . . . . . . . . . . . . . . . . . . 1 33 060183 Gear (29T). . . . . . . . . . . . . . . . . . . . . 1 34 060184 Bearing Shield Cap.. .. .. .. .. ... 2 35 060185 Set Collar . . . . . . . . . . . . . . . . . . . . . 1

650202 SHSS 5/16 x 5/16.... .. ....... 2 36 060186 Washer .................... " . . 1 37 060187 Spacer.... . ...... .... .. ....... 2 38 060188 Set Collar .. . . . . . . . . . . . . . . . . . . . I

650202 SHSS 5/16 x 5/16 .......... '" 2 39 060192 Chain (#60) of 28 Links Including

One (500208) Connector Link. . . I 40 060194 Transmission Housing...... .... . I 41 062823 Gear (l9T).. .. .. .. .... .. .. .. .. . I 42 062825 Clutch Shaft. . . . . . . . . . . . . . . . . . . I 43 062830 Bearing Housing ............... I 44 062831 Drive Shaft. . . . . . . . . . . . . . . . . . . . 1

655533 Woodruff Key 5/ 16 xl. . . . . . .. 3 45 062832 Gear (27T). . . . . . . . . . . . . . . . . . . . . 1 46 062833 Drive Shaft. . . . . . . . . . . . . . . . . . . . 1

655533 Woodruff Key 5/ 16 x I ........ 1 47 063446 HHCS 5/16 x 1-1/4 ............ 6

(6) 5/16 LW 48 063971 HLN 1/2..... ....... .......... 2 49 065064 Gear (l5T)................... .. 1 50 065264 Bumper . . . . . . . . . . . . . . . . . . . . . . . 1 51 065621 Transmission Cover. . . . . . . . . . . . . 1

650486 HHCS 5/16 x 3/4 ........ .. ... 4 (4) 5/16 LW

52 065626 Gasket. . . . . . . . . . . . . . . . . . . . . . .. 3 53 069432 Roller Drive Shaft. . . . . . . . . . . . . . 1

655533 Woodruff Key 5/16 xl........ I 54 069433 Roller Drive Shaft. . . . . . . . . . . . . . 1

655533 Woodruff Key 5/ 16 xl. . . . . . . . 1 55 530008 Oil Seal. . . . . . . . . . . . . . . . . . . . . . . 1 56 540006 Retaining Ring. . . . . . . . . . . . . . . .. 4 57 660004 Pipe Plug. . . . . . . . . . . . . . . . . . . . . . 1

27

CB1250 KNIFE SHARPENER MAIN UNIT

21 N ber _ DOb Part umTAl\'T Order Y Numbers.IMPOR . ton ReferenceNOT use Illustra I

40

28

CB1250 - KNIFE SHARPENER


H488 Cam .......................... 29 062702 Stone Guard ................... I 650545 HHCS 5/16 x 1-1/4 ........... 650486 HHCS 5/16 x 3/4 ............. 2

(1) 5/16 LW - (1) PW (2) 5/16 LW - (1) PW 2 B11069 V-Bolt ........................ 2 30 063472 Knob ......................... 1

(4) 5/16 HN - (4) LW 31 064346 Grease Fitting .................. 1 3 042656 Bronze Bushing ................ 1 32 065073 Ball Bearing ................... 2 4 050270 Roll Pin 3/16 x 1-1/4 ........... 1 33 065075 Knife Guide Spring - Right ...... 1 5 051200 Shim (1/32) .................... 12 (2) 5fl6 HJN 6 051206 Oil Seal ....................... 4 34 065076 Knife Guide Spring - Left ....... 7 051207t Safety Goggles ................. 1 (2) 5j16 HJN 8 051208 Ball Bushing ................... 2 35 065087 Pivot Pin ...................... 2 9 051365 Shim (1/8) ..................... 8 36 065095 Spring Plate - Right ............ 1

10 052044t Dressing Stick ................. 1 650448 H H CS 1/4 x 3/4 .............. 3 11 054886 Washer ........................ 1 (2) 1/4 HN - (3) LW - (1) PW 12 057622 Motor Support. ................ 1 650545 HHCS 5/16 x 1-1/4 ...........

570009 Grease Fitting ................. 1 (1) 5(16 HJN (Includes (2) 059300 Bronze 37 065096 Spring Plate - Left. ............. 1

Bushings) 650448 HHCS 1/4 x 3/4 .............. 3 13 057628t Knife Template .. , .............. (2) 1/4 HN - (3) LW - (1) PW 14 057630 Motor Adjustment Link ......... 650545 HHCS 5/16 x 1-1/4 ...........

650487 HHCS 5/16 xl ............... (1) 5/16 HJN (1) 5/16 LW 38 065367 Grinder Traveler ............... 1

15 057631 Shim.......................... 4 570009 Grease Fitting ................. 3 16 057634 Roll Pin 1/8 x 1-1/4 ............ 1 650196 SHSS 1/4 x 5/16 .............. 2 17 057637 Bellville Washer ................ 6 39 065520 Traverse Rod .................. 1 18 057640 Adjustment Screw .............. 1 (I ncludes (1) 042656 Bronze

650553 Cotterpin 1/8 x 3/4 ............ 1 Bushing) (1) 5/16 PW 40 065523 Rail Support - Left .............

19 058484 Grinding Wheel ................ 1 41 065534 Torque Arm ................... 650488 HHCS 3/8 x 3/4 .............. 4 (1) 1/2 HN - (I) L W

(4) 3/8 LW 42 065535 Hair Pin Clip .................. 1 20 058885 Nut ........................... 1 43 065536 V-Bolt ... ..................... 2 21 059300 Bronze Bushing ................ 2 (4) 5/16 HN - (4) LW 22 060240 Knife Guide Arm ............... 1 44 065538 Washer ........................ 2 23 060260 Knife Guide .... ,,"""""""",,",,"" " 1 45 072240 Stone Hub ..................... 24

25

060268 Radial Bearing ................. (2) 1/4 HN - (2) LW - (3) PW (Narrow)

062373 Front Sharpener Rail ...........

2

1

650692 HHCS 5fl6 x 1-3/4 (1) 1/4 LW

...........

26 062374 Rear Sharpener Rail ............ 1 27 062681 Rail Support - Right ............ 1 28 062691 Guide Arm Support ............ 1

650545 HHCS 5/16 x 1-1/4 ........... 2 650692 HHCS 5/16 x 1-3/4 ........... 1 t Stored in Harvester's Toolbox.

(3) 5/16 LW

29

CB1250 - KNIFE SHARPENER _______________ HYDRAULICS

7

IMPORTANT' Order by Part Number - DO r-.; OT use Illustration Reference r-.; umbers.


1 055021 Hose Clamp .................... 2 15 062241 Velocity Fuse..... .... ...... ... 1 2 055648 Wire Tie ...................... 2 16 064645 Service Tee.. .. .... ... .... .. ... 1 3 056080 Male Quick Disconnect ......... 4 l7 064660 Control Knob.................. 1 4 056081 Female Quick Disconnect.. . . . . .. 2 18 064674 Selector Valve.... .............. 1 5 057635 Motor Mount. . . . . . . . . . . . . . . . . . I 650692 HHCS 5/16 x 1-3/4 ........... 2 6 057636 Spacer.......... . .... .... ..... 1 (1) 5jl6 PW - (2) LW 7 057647 Hose (3/8 x 40) ................ 1 19 064930 Discharge Auger Hose (l / 2 x 44) . 1 8 057648 Ball Valve..................... 1 20 069466 Hose (3/8 x 130) ............... I 9 057649 U-Bolt .......... . .. ...... ..... 1 21 069467 Valve Bracket .............. , . . . 1

10 057654 Needle Valve ................... I 650486 HHCS 5/16 x 3/4 ........ ..... 2 11 057796 Tractor Hose (3/8 x 170) '" .. ... 2 650692 HHCS 5/16 x 1-3/4 ........... 2 12 058654 90° Elbow - 1/2.. ............ .. 3 (2) 5/16 HN - (4) LW - (1) PW 13 060626 Cylinder - 3/8 Dia. ............. 1 22 069468 Hose (3/8 x 62) .............. .. 14 062238A Hydraulic Motor (MTE) ........ 1 23 660062 Close Nipple - 3/8 ............. .

650789 HHCS 5/16 x 4-1/2 ........... 4 (4) 5/16 HN - (4) LW A For Seal Kit, order(1 )063593. For Motor replacement

0660778 Hydraulic Motor (Barnes) ..... . . 1 (I) 057636 Spacer MUST be used. 650545 HHCS 5(16 x 1-1/4 ........... 4 8 For Seal Kit, order(l )066078. For Motor replacement

(4) 5/16 HN - (4) LW (I) 057636 Spacer MUST be used.

30

CB1250 - UNIVERSAL DRIVES UPPER FEED ROLL DRIVE


..f)~f1

- -- Ref. Part!_ No.

1 No. No. Part Name Req.

1 060120 Ball (5/16) .................... . 2 069437 Yoke - 1-1/8 Bore ............. . 3 069439 Yoke - 1-3/8 Bore ............. . 4 071281 Universal Joint wi Spline Tube .. . 5 071282 Splined Yoke Tube ............ .

570004 Grease Fitting ................ . 6 071283 Universal Joint wi Spline Shaft .. . 7 071286 Yoke and Spline Shaft

w / Shear Flange . . . . . . . . . . . . . . . 1 570004 Grease Fitting. . . . . . . . . . . . . . . . . 1

8 510263 Center Cross Kit ............... 2

LOWER FEED ROLL DRIVE

IMPORTANT': Order by Part Number - DO 1\ OT use 1l1ustrat ion Reference N umbers.

//~7/-.-O't.~Ref. Part No.

No. No. Part 'Jame Req.

1 1 060120 Ball(5/16) ..................... I 2 063890 Shear Yoke and Flange ......... 1

570002 Grease Fitting. . . . . . . . . . . . . . . . . 1 3 063892 Yoke (Square Hole) ............. 1 4 069437 Yoke. ... .. . . .. ................ 1 5 069439 Yoke. .. . .... . .... .......... ... 1 6 069443 Universal Joint w/Sq. Hole...... 1 7 071278 Universal Joint w/Sq. Shaft..... 1 8 071279 Square Shaft and Shear Flange. . . I 9 510263 Center Cross Kit ............... 2

31

CB1250 - UNIVERSAL DRIVES TUBULAR MAIN DRIVE

6

NOTE: MAXIMUM OPERATING SPEED: 1170 RPM

IMPORTANT: Order by Part Number - DO NOT use Illustration Reference \lumbers.

1-3/8" TELESCOPING DRIVE


059971A Shear Bolt 3/8 x 1-3/4. ......... (2) 3/8 HLN - (2) PW

2 063894 Yoke w/Spline Shaft. .......... . 3 068127 Universal Joint w/Spline Shaft .. . 4 068128 Flange Yoke .................. .

570002 Grease Fitting ................ . 5 071744 Shear Hub .................... .

570002 Grease Fitting ................ . 6 510197 Center Cross Kit .............. .

A For Replacement Shear Bolts, order only kit 900092 (Containing 8 Shear Bolts)

1

~0 2

NOTE: MAXIMUM OPERATING SPEED: 1200 RPM

IMPORTANT: Order bv Part Number - DO NOT use Illustration Re'ference Numbers.

Part No.

I 047523 2 047524 3 047538 4 062499 5 062500 6 063898 7 063899 8 063900 9 063901

10 063902 II 510197

:r\ o. Part Name Req.

Nylon Bearing ................. 4 Bearing Retainer ............... 4 Guard (Male) ..... .. . ... . ... . .. I Universal Joint w/Spline Shaft... I Universal Joint wi Spline Tube .. . yoke ......................... . Universal Joint w/Spline Shaft .. . U nviersal Joint & Spline Tube .. , Guard (Female) ............... . yoke ......................... . Center Cross Kit .............. .

32

2

CB1250 - UNIVERSAL DRIVES 1-3/4" TELESCOPING DRIVE

IMPORTANT: Order bv Part Number - DO NOT use Illustration Reference Numbers.

1-3/4" PTO DRAWBAR EXTENSION

1~

Ref. Part No. 9 No. No. Part Name Req.

1 047523 Nylon Bearing. . ... ....... . . . .. 4 2 047524 Bearing Retainer .......... . . . . . 4 3 063902 yoke.......................... 1 4 063903 yoke.......................... 1 5 063904 Universal Joint w/Spline Shaft... 1 6 063905 Guard (F~male) .. . . . . . . . . . . . . . . 1 7 063906 Guard (Male) ....... .. .... ..... 1 8 063907 Universal Joint & Spline Tube. . . 1 9 071691 Universal Joint w/Spline Shaft... 1

10 071692 Universal Joint w/Spline Tube... 1 11 510197 Center Cross Kit ............... 2

IMPORTANT: Order bv Part Number - DO NOT use Illustration Re'ference Numbers.

Part No. No. Part Name Req.

1 H8353A Washer. ....................... 2 2 071304 Drawbar Extension ............. 1

650162 HHCS 5/8 x 6-1/2 ............ 2 (2) 5/8 HN - (2) LW

3 071689A Universal Drive - 1-3/4" PTO .... 1 650859 HHCS 5/8 x 3-1/4 ............ 2

(2) 5/8 HN - (2) LW

A See the Universal Drives illustration for the Drive breakdown of service parts.

33

CB1250 - HITCHJACK

IMPORT ANT: Order by Part Number - DO NOT use Illustration Reference Numbers.

5

4

I I I I I I I3 I ~

"

Ref. No.

Part No. Part Name

No. Reg.

Ref. No.

Part No. Part Name

No. Reg.

1 2 3

071117

055682 061276 061341

Hitchjack - Assembled

Consists of: Crank Assembly ............... . Pin & Chain .................. . Inside TUbe ................... .

4 5

061342 071271

Outside TUbe ................. . Jack Repair Kit ............... .

(Includes a Crank Pin, Pushnut, Thrust Washer, Ball & Cage

Bearing Felt Spacer and a Support Washer)

34

CB1250 - TOOLBOX SUPPLIES

TOOLBOX SUPPLIES

NOTE: The following listing identifies all of the parts which are furnished in the Harvester Toolbox when shipped from the factory. The listing is separated into parts used for Set-up & Assembly and parts used for Field Operation.

Set-up & Assembly Parts

Part No. No. Part Description Req. Where Used

055021 Hose Clamp ..................... . As required 056336 Cap Spring ..................... . Deflector to Cap connection 058778 Hitch Control Cord .............. . Drawbar Latch to tractor connection 061872 HTFS 5/16 x 3/4 ................ . Secure 055021 Hose Clamp 071663 Hitch Pole Pivot Pin ............. . Drawbar to Frame connection

Field Operation Parts*

Part No. No. Part Description Req. Where Used

lJH300 Lock Pin............... ......... 2 Secure Quick Switch Pins 046777 Quick Switch Pin. . . . . . . . . . . . . . . . . 2 Attachment to Harvester connection 051207 Safety Goggles ................... I For Sharpening Knives 052044 Dressing Stick. . . . . . . . . . . . . . . . . . . . I For Knife Sharpener Stone 057628 Knife Template. . . . . . . . . . . . . . . . . . . I For checking Knife bevel 059971 Shear Bolt 3/8 x 1-3/4 ............ 4 Installed in Shear Bolt Holder 060587 Hitch Pin. ... . . . . . . . . . . . . . . . . . . . . 1 Drawbar to tractor connection 062911 Chain (#60H) of 64 Links. . . . . . . . . . I Attachment to Harvester Drive connection 063567 Shear Bolt 5jl6 x 1-1/2 ........... 4 Installed in Shear Bolt Holder 063592 Wire Tie............ .. .. . ... ..... 2 As required 071734 Clutch Link Kit .................. I Spare assembly for Feed Roll Drives

*What Customer would normally place back into Toolbox sometime during Harvester use

35

CB1250 - OPTIONS 801937

TANDEM AXLES & WHEELS SET

9

10

Ref. Part No. Ref. Part No. No. No. Part Name Req. No. No. Part 0:ame Reg.

801937 Tandem Axles, Wheels & Tires Set 1 Consists of: 11 069213 Bearing Cup ................... 4

I H8055A Shim Washer .................. 4 12 069214 Bearing Cone .................. 4 2 042161 Wheel Hub Assembled .......... 4 13 069215 Grease Seal .................... 2

(Includes one 042162 & one 520054 14 069216 Pivot Shaft Nut ................ 2 Bearing Cup) 650577 HHCS 5/16 x 1-1/2 ........... 2

3 042162 Bearing Cup ................... 4 15 069217 Housing Cover ................. 2 4 042163 Bearing Cone .................. 4 650542 HHCS 1/4 x 1/2 .............. 12 5 045581 Valve Stem .................... 4 (12) 1/4 LW 6 048059 Axle Seal ...................... 4 16 069218 Spindle Hub Assembled ......... 4 7 048060 Wheel 15 x 8 ................... 4 (Hub includes part numbers

(For 9.5 x 15 6-Ply Tire) H8055A, 042161,042163,048059, 8 069195 Axle Extension ................. 2 520201,550041,550075 & 9 069199 Wheel Beam - Right ............ 1 653102)

655025 Cotter Pin 3/16 x 2-1/2 ........ I 17 069219 Spindle ........................ 4 650767 HHCS 1/2 x 3/4 .............. 3 18 069225 Spacer ........................ 2 650453 H H CS 1/2 x 1-1/2 ............ 12 19 520054 Bearing Cup ................... 4

(12) 1/2 LW - (12) PW 20 520201 Bearing Cone .................. 4 10 069210 Wheel Beam - Left .............. I 21 550041 Wheel Bolt .................... 24

655025 Cotter Pin 3/16 x 2-1/2 ........ 1 22 550075 Dust Cap ...................... 4 650453 HHCS 1/2 x 1-1/2 ............ 12 23 653102 Slotted Nut - 7/8 ................ 4

(12) 1/2 LW - (12) PW 655014 Cotter Pin 1/8 x 2 ............. 4

36

CB1250 - OPTIONS 802089

SINGLE WHEEL AXLE SET

I M PORT ANT: Order by Part N um ber - DO NOT use Illustration Reference l\umbers.

Ref. Part No. Ref. Part No. No. Part Name Req. No. No.

802089 Single Wheel & Axle Set Consists of:

........ I 8 063621

042161 Wheel Hub Assembled .......... 2 (Includes one 042162 Cup & one

520054 Cup) 2 042162 Bearing Cup ................... 2 3 042163 Bearing Cone .................. 2 9 070514 4 047890 Axle Spacer ................... 2 10 520054 5 048059 Oil Seal ....................... 2 11 520201 6 052501 Washer ........................ 2 12 550041 7 062554 Adjustable Spindle .............. 2 13 550075

650453 HHCS 1/2 x 1-1/2 ............ 8 14 653102 (8) 1/2 HN - (8) LW 655014

WHEEL SETS (Use only with Single Wheel Axles.)

Ref. Part No. No.

1 045581 850195r 2 048060

1 801092

No. Part Name Req.

Wheel Spindle Assembly ........ (Hub includes part numbers

042161,042163,047890,048059, 520501,062554,520201,550041,

550075 & 653102)

2

Axle Extension ................. 2 Bearing Cup ................... 2 Bearing Cone .................. 2 Wheel Bolt .................... 12 Hub Cap ...................... 2 Axle Nut ...................... 2 Cotter Pin 1/8 x 2 ............. 2

No. Part Name Req.

Valve Stem. . . ... . .. . . ... .. . . . . 2 Wheel Set .................... .

Consists of: Wheel 15 x 8.00 ............. ... 2 (For 10 x 15 or 11 L x 15 8-Ply Tires)

Wheel Set .................... .

2 042165 Consists of:

Wheel 15 x 10.00 . . . . . . . . . . . . . .. (For 12.5L x 15 8-Ply Tires)

2

37

CB1250 - ACCESSORIES

HORIZONTAL DEFLECTOR EXTENSION KITS 3-1/2 Ft Horizontal Extension 802176* 5-1/2 Ft. Horizontal Extension 802177* ./"

*Both Kits include Tripod ~it 802133 & Hydraulic ~ '. Controls Kit 802132 /" / ........::)~( Q) • ~./ 3

~ /"

/"

/ /

/ /" / /"

/ /" / /"

/ / /

/ /

/

/" 7/

/ /

/

/

:

4

J IMPORTANT: Order by Part Number - DO NOT use Illustration Reference Numbers.

Ref. Part No. Ref. Part No. No. No. Part l\ame Reg. No. No. Part :"lame Req.

I BI1433A S-Hook....................... I 7 063679 Extension Tie. . . . . . . . . . . . . . . . . . I 2 040860 Ludwig Clip. . . . . . . . . . . . . . . . . .. 2 650943 STHMS 1/4 x 1/2..... . ....... 2

650548 RHMS #1024 x 1/2............ 2 (2) 1/4 HN - (2) LW (2) #1024 HN - (2) LW 8 063680 Clean-out Cover. . . . . . . . . . . . . . . . I

3 056061 Wire Rope Clamp 1/8".... ...... 2 9 070416 Deflector Brace ................ 1 4 058539 Pulley. .... . .... . . . . . .. ... . . . . . I 650495 HHCS 1/2 x 1-1/4 ............ 4 5 060974 Cap Control Cable ............. I 650496 HHCS 1/2 x 5 .......... ...... 2 6 063674 Horizontal Extension (3-1/2 Ft) . . I (6) 1/2 HN - (6)LW - (4) PW

650943 STHMS 1/4 x 1/2............. 2 10 071256 Horizontal Extension Bracket. . . . I (2) 1/4 HK - (2) LW

063681 Horizontal Extension (5-1/2 Ft) . . 1 650949 650950

STHMS 5/16 x 3/4 ............ STHMS 5/16 x I..............

10 7

650943 STHMS 1/4 x 1/2............. 2 650952 STHMS 5/16 x 1-1/2.. . . .... .. I (2) 1/4 HN - (2) LW (18) 5/16 HN - (18) LW - (4) PW

38


802071 802072 1-FT VERTICAL DEFLECTOR EXTENSION KIT 2-FT VERTICAL DEFLECTOR EXTENSION KIT

., ., ..... ~-----tV., IMPORTANT: Order by Part Number - DO NOT use IIIustration Reference Numbers.

ef. Part No. o. No. Part Name Req.

Ref. 802071 I-Ft Vertical Deflector No.

Extension Kit ............... . Consists of:

I 9 H363 Spacer ....................... . 8 2 070411 I-Ft Vertical Extension ......... . I

650502 HHCS 1/2 x 2-1/4 .......... . 8 I (8) 1/2 HLN 2

3

4 5 6

7

8

IMPORTANT: Order by Part Number - DO NOT use IIIustration Reference Numbers.

i

, r, ~ .~ : ~

!./f~ ~\~ \..- > /".,.[~, 1.j"'- "--_~r:-~-<


802072 2-Ft Vertical Deflector Extension Kit ................

Consists of: 9H363 Idler Crank Hub ............... 8 811069 V-Bolt ................... , I

(2) 5Jl6 HLN 044116 Latch ......................... I

650812 RHMS #1224 x 1/2 ........... 2 (2) #1224 HN - (2) LW - (2) PW

057440 Cover ......................... 1 059721 Cable Guide ................... I 070414 2-Ft Vertical Extension .......... I

650502 HHCS 1/2 x 2-1/4 ........... 8 (8) 1/2 HLN

071086 Cap Motor Bracket ............. 1 650486 HHCS 5fl6 x 3/4 ............ 2

(2) 5Jl6 HN - (2) LW 071228 Cable Guide Bracket ... , ........

39


802133 TRIPOD KIT

~'-

Ref. No.

2

3

4

5 6

7 8

9

\ 9

7

IMPORTANT: Order by Part Number - DO NOT use lJIustration Reference Numbers.


046866 Cam .......................... 2 650502 HHCS 1/2 x 2-1/4 ............ 2

(2) 1/2 HN - (2) LW 063695 Tripod Brace - Side .............

650744 HHCS 1/2 x 4 ................ (2) 1/2 HN - (2) PW

063698 Brace Support - Front .......... 1 650502 HHCS 1(2 x 2-1/4 ............ 2

(2) 1/2 HN 063699 Tripod Brace - Front. ...........

650585 HHCS 1/2 x 2 ................ (2) 1(2 HN - (2) PW

065623 Washer ........................ 2 068073 Tripod Stand - Vertical. ......... 1

650744 HHCS 1/2 x 4 ................ 2 (2) 1/2 HN

070400 Spacer ........................ 070401 Deflector Pivot .................

650454 HHCS 1/2 x 3-3/4 ............ (1) 1/2 HLN

650532 HHCS 5/8 x 1-1/2 ............ 4 (4) 5/8 HN

071343 Deflector Bracket. ..............

40


7

8 IMPORTANT: Order by Part Number - DO NOT use lIlustration Reference Numbers.

Ref. Part No. Ref. Part l'\o. No. No. Part Name Req. No. No. Part Name Req.

I M12413 Cylinder Pin. .. .. .. .. .. .. .. .. .. I 5 070449 Deflector Pivot ................ . 4 2 055021 Hose Clamp ................... 2 650569 HHCS 1/2 x 1-3/4 .......... .. 4

650487 HHCS 5/16 xl............... 2 650585 HHCS 1/2 x 2 ............... . 4 (2) 5/16 HN - (2) LW (8) 1/2 HLN

6 070450 Deflector Clamp ............... . 23 056338 Blower Channel Shim. . . . . . . . . . . 2 7 070451 Deflector Cylinder Bracket ...... . 24 058757 Swivel Adapter Union... . . .. . . .. 2 8 071297 Cylinder Support .............. . 1

9 071303 Cylinder Bracket Support. ...... . I

802134 DEFLECTOR TRIPOD EXTENSION


802134 Deflector Tripod Extension ..... . Consists of:

063707 Tripod Extension. . . . . . . . . . . . . . . I 650744 HHCS 1/2 x 4................ 2

(4) 1/2 HN

41


802090 ELECTRIC TRACTOR EXTENSION CONTROLS

IMPORTANT: Order by Part Number - DO NOT u'" IlIu,"";o" R,f","" Numb",. ~1

Ref. No.

Part No. Part Name

No. Reg.

I 2 3

802090

B11433A 058539 068209

Electric Tractor Extension Controls Kit .................

Consists of: S-Hook ~ ...................... Pulley ......................... Pulley Cord ....................

802172 AUXILIARY LIFT SPRING KIT


I H8353A Washer ....................... . 2 BI1201 A Take-up Bolt 5/8 x 7 .......... . 3 062531 Lift Extension Spring .......... . 4 062532 Lift Spring Nut ............... .

6

Ref. Part No. No. 1'\ o. Part Name Re<.].

4 071077 Receptacle Clamp ............. . (2)5/16 HLN

5 071078 Receptacle Bracket ............. I 650487 HHCS 5fl6 xl. ..... . . . . . . .. 4

(4) 5/16 HN - (2) LW - (2) PW 6 071092 Wiring Harness Extension ...... .

801136 HYDRAULIC DEFLECTOR CYLINDER & HOSE KIT

Ref. Part No. No. No. Part 1\arne Req.

801136 Hydraulic Cylinder & Hose Kit. .. Consists of:

I 060626 Hydraulic Cylinder ............. I 2 0610 lOA Hose (1/2 x 276) ............... 2 3 072256 Cylinder Pin ................... 1

655020 Cotterpin 3/16 x 1-1/2 ......... 2

A Two (058757) 90° Swivel Adapter Unions, that attach to the Hoses, are NOT included in Kit; but are furnished with the Toolbox parts or Electrical Controls illustration.

42


070393 802079 DEFLECTOR LINER KIT ELECTRIC REMOTE 3-SWITCH CONTROL BOX

(For Service Only)


Ref. No.

Part No. Part Name

No Req

070393

070393 650541

Deflector Liner Kit ............ . Consists of:

Deflector Liner ................ . PB 5/16 x I ................ .

(6) 5/16 HN - (6) LW - (6) PW

046442 KNIFE TORQUE WRENCH


046442 Knife Torque Wrench .......... . Consists of:

046442 Torque Wrench ............... .

~.

2 /~ ~~4

6


802079 Electric Remote 3-Switch Control Box ......................... .

Consists of: 059053 Mounting Bracket. . . . . . . . . . . . .. 2

650663 HHCS 1/4 x 5/8 .............. 6 (6) 1/4 HN - (6) LW - (4) PW

2 059074 Open-Closed - Bushing ......... . 3 071053A 3-Switch Control Box - Assembled 4 071077 Receptacle Clamp ............. .

(2) 5/16 HLN 5 071078 Receptacle Bracket ............. 1

650487 HHCS 5/16 xl. .............. 4 (4) 5/16 HN - (2) LW - (2)PW

6 071079 Universal Bushing ............. . 7 071166 Tractor Plug Cap ............. ..

A For Components, see 3-Switch Control Box illustration.

063663 LENGTH-OF-CUT GEAR KIT

2


063663 Length-of-Cut Gear Kit ..... . . . . 1 Consists of:

061700 Shear Bolt 5/16 x 1-3/4 (Gr. 2) .. 4 (Not IIIustra ted)

1 063664 Gear (l4T) .............. , ..... . 2 063665 Gear (34T) .................... .

43


801159 1" SLOTTED SILAGE SCREEN KIT

Ref. Pan No. No. No. Part Name Reg.

801159 I" Slotted Silage Screen Kit. ..... Consists of:

I 058707 Adjustable Eccentric ............ 3 2 064387 Partial Head Carriage Bolt

1/2x2-1/4 ................... 4 (4) 1/2 HN - (4) LW

3 067894 I" Slotted Silage Screen ......... I 650791 CB 1/2 x 1-3/4 ................ 3

(3) 1/2 HN 4 067895 Screen Bracket ................. I

650740 CB 1/2 x 2-1/4 ................ 2 (2) 1/2 HN - (2) LW

SQUARE HOLE SCREENS

Size Part No.

3/4" 063643 I" 063640 I-I 4" 063637 I-I 2" 063634 2" 063631 3" 063628 4" 063622

071230 WET CROP DEFLECTOR KIT

Ref. Part No. No. No. Part ~ame Reg.

071230 Wet Crop Deflector Kit ........ . Consists of:

071231 Wet Crop Baffle ............... .

44

CB1250 - NUMERICAL INDEX

Part No. Page No. Part No. Page No. Part No. Page No. Part No. Page No.

13E24 ............ 23 042814 ........... 25 052044 ........... 29 057796 ........... 30 3H55A ........ 15,27 042815 ........... 25 052501 ........... 37 058357 ........... 23 6H130 ............ 12 042856 .........•.. 7 052884 ............ 7 058368 ........... 23 6H154 ............ 23 042864 ........... 27 053719 ........... 17 058484 ........... 29 H193A ........... 17 043020 ............ 7 054042 ........... 19 058539 ...... 23,38,42 HI95A ........... 17 043178 ........... 15 054174 ........... 13 058654 ........... 30 H267A ........... 27 043684 ............ 7 054175 ........... 13 058707 ........... 44 H275 ............. 27 043690 ........... 27 054176 ........... 13 058757 ........ 4 1,42 9H300 ....... 5,7,9,1 I 043691 ........... 27 054333 ........... 17 058778 ............ 5 C354 '" .......... 25 043692 ........... 27 054559 ........... 17 058885 ........... 29 17H361 ............ 7 043693 ........... 27 054586 ........... 17 058889 ........... 25 9H363 ......... 21,39 043694 ........... 27 054886 ........... 29 059050 ........... 23 17H386 ........... 23 043836 ........... 25 055021 .... 7,11,30,41 059053 ........ 23,43 H488 ............. 29 043837 ........... 25 055281 ........... 25 059064 ........... 24 H6073F ........... 7 043838 ........... 25 055284 ........... 25 059065 ........... 24 H6075 ........ : .. 7,13 043841 ........... 25 055447 ........... 15 059066 ........... 24 H6094 ............. 5 044110 ........... 27 055449 ........... 25 059074 ........ 23,43 H6208 ............ 19 044 I 16 ........ 11,39 055494 ........... 19 059075 ...... I 1,2 1,23

044777 ............ 5H8055A .......... 36 055582 ........... 21 059084 ............ 7 045026 ............ 5H8224 ............ 17 055648 ........... 30 059085 ............ 7 045581 ........ 36,37H8353A ...... 5,33,42 055682 ........... 34 059272 ........... 1 I

H8365 ............ 23 045668 ........ 25,27 055690 ........... I I 059299 ........... 24 D9117A ........... 5 045818 ........... 17 055691 ........... 11 059300 ........... 29

045819 ........... 17D9130 ............. 7 055692 ........... 1 I 059313 ........... 23 VIOl 10 ........... 15 046145 ........... 17 055746 ........... 13 059321 ........... 23

046442 ........... 43BI1069 ........ 29,39 056061 ........ 23~8 059489 ........... 25 046526 ........... 17BII162B ........... 7 056080 .... '" .... 30 059548 ........ 17,27

BI120IA ........ 5,42 046673 '" ........ 17 056081 ........... 30 059721 ........... 39 BI1245 ............ 5 046777 ............ 5 056249 ........... 27 059971 ........ I 1,32 B11433A ..... 23,38,42 046847 ........... 17 056272 ........... 17 060000

046848 ........... 17MI2361 ........... 7 056273 ........... 17 060 I 20 ..........• 3 I 046864 ............ 9MI2413 .......... 41 056282 ........... 27 060154 ........... 27

R13007C ......... 17 056283 ............ 7 060160 ........... 27046866 ......... 9,40 R13077 ........... 25 046873 ... ; ........ 9 060161 ........... 27056336 ........... 12

056338 ........ 15,41R13078 ........... 25 047269 ........... I I 060164 ........... 27 R13079 ........... 25 047523 ........ 32,33 056341 ........... 27 060167 ........... 27 R13113 ........... 17 047524 ........ 32,33 056352 ........... 27 060170 ........... 27 R13178 ........... 23 047538 ........... 32 056468 ............ 7 060171 ........... 27 R13245 ............ 5 047621 ........... 21 056640 ......... 7,25 060172 ........... 27 SI6215 ........... 21 047890 ........... 37 057440 ........... 39 060173 ........... 27

040000 048028 ........... 21 057557 ............ 7 060175 ........... 27 040860 ........ 12,38 048059 ........ 36,37 057586 ........... 17 060176 ........... 27 041489 ............ 7 048060 ........ 36,37 057617 ......... 7,15 060180 ........... 27 041499 ........... 15 048512 ........... 27 057622 ........... 29 060183 ........... 27 041881 ......... 5,27 049344 ........... 27 057628 ........... 29 060184 ........... 27 041916 ........... 25 049366 ........... 27 057630 ........... 29 060185 ........... 27 041917 ........... 25 049367 ........... 25 05763 I .......... '. 29 060 I 86 ........ 2 I ,27

049371 ........... 17042158 ........... 25 057634 ........... 29 060187 ........... 27 042161 ........ 36,37 050000 057635 ........... 30 060188 ........... 27 042162 ........ 36,37 050270 ....... 5,17,29 057636 ........... 30 060192 ........... 27 042163 ........ 36,37 051200 ........... 29 057637 ........... 29 060194 ........... 27 042165 ........... 37 051206 ........... 29 057640 ........... 29 060240 ........... 29 042656 ........... 29 051207 ........... 29 057647 ........... 30 060258 ........... 1 I 042657 ........... 21 051208 ........... 29 057648 ........... 30 060260 ........... 29 042658 ........... 21 051365 ........... 29 057649 ........... 30 060268 ........... 29 042811 ........... 25 051525 ........... 21 057654 ........... 30 060279 ............ 7 042813 ........... 25 051948 ............ 7 057781 ........... 24 060369 ........... 23

45

CB1250 - NUMERICAL INDEX _______________


060587 ............ 5 062601 ............ 9 062825 ........... 27 064238 ........... 23 060626 ........ 30,42 062602 ............ 9 062829 ............ 7 064239 ........... 23 060972 ........... 24 062603 ............ 9 062830 ........... 27 064346 ........... 29 060974 ........ 23.38 062604 ............ 9 062831 ........... 27 064387 ........... 44 060979 ............ 7 062607 ............ 9 062832 ........... 27 064519 ............ 5 061006 ............ 7 062614 ............ 7 062833 ........... 27 064645 ........... 30 061010 ........... 42 062617 ........... 15 062834 ............ 7 064660 ........... 30 061267 ............ 9 062635 ........... 15 062835 ........... 15 064674 ........... 30 061276 ........... 34 062642 ........... II 062844 ............ 9 064930 ........... 30 061341 ........... 34 062643 ......... 7,15 062870 ............ 9 065059 ........... 13 061342 ........... 34 062659 ........... 15 062871 ........... 17 065064 ........... 27 061700 ........... 43 062663 ........... 15 062886 ........... II 065073 ........... 29 061809 ........... 15 062665 ........... 13 062887 ........... II 065075 ........... 29 061838 ............ 5 062666 ........... 13 062890 ............ 7 065076 ........... 29 061839 ............ 5 062667 ......... 7,13 062891 ............ 7 065087 ........... 29 061840 ............ 9 .062668 ........... 13 062898 ........... 11 065095 ........... 29 061843 ........ 17,21 062671 ........... 13 062900 ........... J 1 065096 ........... 29 061845 ........ 17,21 062673 ............ 5 062901 ........... 11 065185 ........ 17,21 061847 ........ 17,21 062680 ........... 15 062906 ............ 5 065213 ............ 9 061848 ........ 17,21 062681 ........... 29 062907 ........... 11 065230 ........... 17 061872 ........ 11,17 062691 ........... 29 062908 ........... 13 065251 ............ 5 061930 ............ 5 062702 ........... 29 062911 ............ 7 065252 .......... 7.9 062225 ............ 7 062738 ........ 19,21 063446 ........... 27 065253 ............ 9 062227 ............ 7 062740 ........... 21 063472 ........... 29 065254 ........... 21 062238 ........... 30 062750 ........... 21 063567 ........... 19 065264 ........... 27 062241 ........... 30 062753 ........... 21 063593 ........... 30 065268 ........... 12 062252 ........... 13 062754 ........... 21 063621 ........... 37 065367 ........... 29 062287 ........... 25 062756 ........... 21 063646 ........... 23 065368 ........... 15 062354 ........... 23 062774 ............ 9 063649 ........... 23 065369 ........... 15 062359 ........... 23 062775 ........... 19 063663 ........... 43 065373 ........... 15 062373 ........... 29 062776 ........... 21 063664 ........... 43 065520 ........... 29 062463 ............ 5 062777 ........... 19 063665 ........... 43 065523 ........... 29 062488 ............ 5 062778 ........... 19 063667 ............ 5 065527 ........... 21 062490 ............ 5 062782 ........... 11 063668 ............ 5 065528 ........... II 062491 ............ 5 062783 ......... 7,25 063674 ........... 38 065534 ........... 29 062493 ........... 11 062784 ........... 25 063679 ........... 38 065535 ........... 29 062499 ......... 7,32 062785 ........... 25 063680 ........ 12,38 065536 ........... 29 062500 ......... 7,32 062786 ........... 25 063681 ........... 38 065538 ........... 29 062511 ............ 5 062788 ........... 25 063695 ........... 40 065621 ........... 27 062531 ......... 5,42 062789 ........... 25 063698 ........... 40 065623 ........... 40 062532 ......... 5,42 062790 ........... 25 063699 ........... 40 065624 ........... 21 062533 ............ 5 062791 ........... 25 063707 ........... 41 065626 ........... 27 062539 ............ 5 062792 ........... 25 063872 ........... 17 065640 ........... 17 062540 .. , ......... 5 062793 ........... 25 063890 ........... 31 065641 ........... 17 062542 ............ 5 062794 ........... 25 063892 ........... 31 065642 ........... 17 062543 ............ 5 062795 ........... 25 063894 ........... 32 065646 ........... 17 062544 ............ 5 062796 ........... 25 063898 ........... 32 065647 ........... 17 062545 ............ 5 062797 ........... 25 063899 ........... 32 065658 ............ 7 062546 ............ 5 062798 ........... 11 063900 ........... 32 065838 ............ 5 062553 ............ 5 062804 ........... 13 063901 ........... 32 065847 ............ 5 062554 ........... 37 062805 ........... 13 063902 ........ 32,33 065850 ............ 5 062569 ........... 17 062806 ........... 13 063903 ........... 33 066077 ........... 30 062583 ........... 17 062810 ........... 13 063904 ........... 33 066078 ........... 30 062585 ........... 17 062811 ........... 13 063905 ........... 33 066369 ........... 19 062586 ........... 17 062812 ........... 13 063906 ........... 33 066549 ........... 21 062594· ........... 11 062823 ........... 27 063907 ........... 33 066612 ........... 21

. 062597 ............ 9 062824 ............ 7 063971 ........... 27 066614 ........... 21

46

_______________ CB1250 - NUMERICAL INDEX


066638 ........... 11 069403 ........... 21 070870 ........... 19 071326 ........... 12 066640 ........... 1 I 069404 ........... 21 07C~74 ........... 19 071328 ........... 17 066641 ........... 11 069406 ........... 21 071053 ...... 23,24,43 071329 ........... 15 066642 ........... 1 I 069407 ........... 21 071054 .......... 24 071330 ........... 15 066643 ........... 11 069408 ........... 19 071068 ........... 24 071331 ........... 15 066644 ........... 11 06941 I ........... 19 071069 ........... 24 071332 ........... 15 066681 ........... 15 069414 ........... 21 071070 ........... 24 071334 ........... 15 066684 ........... 15 069416 ........... 19 071071 ........... 24 071336 ........... 23 066696 " .......... 5 069422 ........... 21 071072 ........... 24 071338 ............ 5 067833 ........... 21 069423 ........... 11 071073 ........... 24 071343 ........... 40 067894 ........... 44 069424 ........... 11 071077 ...... 23,42,43 071351 ........... 11 067895 ........... 44 069425 ........... 21 071078 ...... 23,42,43 071354 ........... 11 068073 ........... 40 069431 ......... 7,27 071079 ........ 23,43 071355 ........... II 068117 ........... 13 069432 ........... 27 071080 ........... 23 071356 ........... II 068118 ........... 13 069433 ........... 27 071082 ........... 23 071357 ........... II 068120 ........... 23 069437 ........... 31 071083 ........... 23 071358 ........... 11 068124 ............ 5 069439 ........... 31 071084 ........... 23 071359 .... : ...... 11 068127 ......... 7,32 069443 ........ 19,31 071085 ........... 23 071361 ........... 17 068128 ........... 32 069466 ........... 30 071086 ........... 39 071366 ........... II 068130 ........... 11 069467 ........... 30 071087 ........... 23 071369 ........... 11 068132 ........... I I 069468 ........... 30 071089 ........... 23 071432 ........... 15 068133 ........... 11 069635 ........... 21 071090 ........... 23 071443 ............ 7 068134 ............ 5 069636 ........... 21 071092 ........... 42 071446 ............ 7 068190 ........... 17 069766 ....... , .... 5 071117 ......... 5,34 071447 ............ 7 068198 ........... 17 069869 ........... 17 071118 ........... 21 071448 ............ 9 068199 ........... 17 070000 071166 ........ 23,43 071449 ............ 5 068200 ........... 17 070062 ........... 21 071167 ........... 21 071482 ............ 9 068209 ........... 42 070069 ........... 21 071169 ........... 21 071486 ............ 9 068280 ......... 7,13 070074 ........... 13 071171 ........... 21 071487 ............ 9 068734 ........... 13 070105 ........... 17 071209 ........... 23 071488 ............. 9 068740 ............ 9 070108 ........... 17 071210 ........... 23 071495 ............ 9 068901 ............ 9 070112 ........... 17 071228 ........... 39 071503 ............ 9 069087 ........... 11 070116 ........... 17 071230 ........... 44 071504 ............ 9 069195 ........... 36 070170 ........... 15 071231 ........... 44 071505 ............ 9 069199 ........... 36 070378 ........... 12 071234 ........... 23 071507 ............ 9 069210 ........... 36 070393 ........ 12,43 071235 ........... 23 071508 ............ 7 069213 ........... 36 070400 ........... 40 071236 ............ 5 071559 ........... 19 069214 ........... 36 070401 ........... 40 071256 ....... , ... 38 071569 ............ 9 069215 ........... 36 070411 ........... 39 071257 ........... 24 071571 ........... 21 069216 ........... 36 070414 ........... 39 071271 ........... 34 071573 ........... 11 069217 ........... 36 070416 ........... 38 071277 ........... 19 071574 ........... 23 069218 ........... 36 070449 ........ 23,41 071278 ........ 19,31 071579 ........... 11 069219 ........... 36 070450 ........ 23,41 071279 ........... 31 071663 ............ 5 069225 ........... 36 070451 ........... 41 071280 ........... 19 071689 ........... 33 069245 ........... 23 070452 ........... 23 071281 ........ 19,31 071691 ......... 7,33 069298 ........... 13 070453 ........... 23 071282 ........... 31 071692 ......... 7,33 069370 ........... 21 070454 ........... 23 071283 ........ 19,31 071703 ........... 17 069372 ........... 19 070463 ........... 23 071286 ........... 31 071734 ........... 19 069378 ........... 19 070466 ........... 23 071287 ............ 9 071736 ........... 24 069387 ........... 21 070467 ........... 23 071297 ........... 41 071737 ........... 24 069388 ........... 21 070468 ........... 23 071303 ........... 41 071738 ........... 24 069389 ........... 21 070483 ............ 5 071304 ........... 33 071743 ............ 7 069391 ........... 19 070484 ............ 5 071307 ............ 5 071744 ........... 32 069394 ........... 19 070485 ............ 5 071321 ........... 17 071745 ............ 7 069399 ........... 21 070514 ........... 37 071322 ........... 19 071746 ............ 7 069400 ........... 19 070516 ........... I I 071324 ........... 19 071773 ............ 9 069402 ........... 19 070613 ............ 7 071325 ........... 19 072082 ............ 9

41

CB1250 - NUMERICAL INDEX _______________


072199 · ...... , ... 23 072240 ........... 29 072256 ......... 5,42 072258 ........... 15

500000 500057 ........... 19 500058 ........... 19 500078 ........... 19 510 197 ........ 32,33 510263 · .......... 31 520054 ........ 36,37 520093 · .......... 15 520098 ......... 5,15 520099 ......... 5,15 520103 ............ 9 520105 ........... 13 520153 · .......... 21 520188 · .......... 13 520201 ........ 36,37 530008 · .......... 27 540006 ........... 27 540022 ........... 21 550041 ........ 36,37 550075 ........ 36,37 570002 ... 7,9,13,21,31 570004 · .......... 31 570009 ........... 29 570011 · -....... 17,21 570014 ............ 5 570019 .... 5,15,17,21 570023 ........... 15

600000 660004 ........ 25,27 660062 ........... 30 653102 ........ 36,37

800000 801136 ........... 42 801159 ........... 44 801160 ........... 44 801161 ........... 44 801163 ........... 44 801164 ........... 44 801165 ........... 44 801166 ........... 44 801937 · .......... 36 802071 ........... 39 802079 ........... 43 802089 ........... 37 802090 ........... 42 802134 ........... 41 850195 · .......... 37

900000 900014 ........... 19 900092 · .......... 32

48

TORQUE SPECIFICATIONS FOR STANDARD MACHINE HARDWARE

SIZE SAE GRADE #2 0 SAE GRADE #5 0 SAE GRADE #8 0-/DRY LUB. DRY LUB. DRY LUB.

·8 - 32 19 In. Lbs. 14 In. Lbs. 30 In. Lbs. 22 In. Lbs. 41 In. Lbs. 31 In. Lbs. 8 - 36 20 " 15 " 31 " 23 " 43 " 32 " 10 - 24 27 " 21 " 43 " 32 " 60 " 45 " 10 - 32 31 " 23 " 49 " 36 " 68 " 51 " 1/4 - 20 66 " 50 " 9 Ft. Lbs. 75 " 12 Ft. Lbs. 9 Ft. Lbs. 1/4 - 28 76 " 56 " 10 " 86 " 14 " 10 " 5/16 - 18 11 Ft. Lbs. 9 Ft. Lbs. 17 " 13 Ft. Lbs. 25 " 18 " 5/16 - 24 12 " 9 " 19 " 14 " 25 " 20 " 3/8 - 16 20 " 15 " 30 " 23 " 45 " 35 " 3/8 - 24 23 " 17 " 35 " 25 " 50 " 35 "

7/16 - 14 32 " 24 " 50 " 35 " 70 " 55 " 7/16 - 20 36 " 27 " 55 " 40 " 80 " 60 " 1/2 - 13 50 " 35 " 75 " 55 " 110 " 80 " 1/2 - 20 55 " 40 " 90 " 65 " 120 " 90 " 9/16 - 12 70 " 55 " 110 " 80 " 150 " 110 " 9/16 - 18 80 " 60 " 120 " 90 " 170 " 130 "

5/8 - 11 100 " 75 " 150 " 110 " 220 " 170 " 5/8 - 18 110 " 85 " 180 " 130 " 240 " 180 " 3/4 - 10 175 " 130 " 260 " 200 " 380 " 280 " 3/4 - 16 200 " 150 " 300 " 220 " 420 " 320 " 7/8 - 9 170 " 125 " 430 " 320 " 600 " 460 "

7/8 - 14 180 " 140 " 470 " 360 " 660 " 500 "

1 - 8 250 " 190 " 640 " 480 " 900 " 680 " 1 - 12 270 " 210 " 710 " 530 " 1000 " 740 "

Multiply In. Lbs. by (8.890) or Ft. Lbs. by (1.383) for metric Nm

NOTE: These torque values are to be used for all GEHL hardware excluding: locknuts, self-tapping screws, thread forming screws, and sheet metal screws. Unless otherwise noted, all torque values must meet this specification.

Attaching Hardware Table

Size & Part Size & Part Size & Part Size & Part Description Number Description Number Description Number Description Number

#10-24 650550 1/4PW 654002 3/8LW 654026 5/8HN 653021 #1OLW 650549 5j16HN 653007 3/8PW 654006. 5/8LW 654032 # !OWN 650937 5/16HLN 070701 1/2HN 653018 5/8PW 654012 #12-24HN 650627 5fl6WN 653094 1/2HJN 653044 3/4HN 653026 #12LW 650813 5/16LW 654024 1/2HLN 071706 3/4HJN 650857 #12PW 650854 5/16PW 654004 1/2SN 653081 3/4LW 654034 1/4HN 653005 3/8HN 653010 1/2LW 654030 3/4PW 654014 Ij4LW 654022 3/8HLN 071703 1/2PW 654009

FARM EQUIPMENT GEHL COMPANY WEST BEND, WISCONSIN 53095 U.S.A.

902734/2.5M1 P381 Printed in U.S.A.

Documents

Forage Harvester · Forage Harvester ~ ~ .[Q1 ~ (g). ~ J . I . W . SERVICE PARTS MANUAL . l!J . Mr. Dealer: When ordering service parts, specify the correct part number, full description,