Fokker Dr.I

F36

1.5mmx175mm Carbon Rod

F46 F15F13

F12

F35

F37

F38F39

1.5mmx250mmCarbon Rod

F41

F44

F45

F17

F16

F22F40 F22-1

F21F43

F20

F19

F18

F5 F7

F6

F3

Ａ5

Ａ3

Ａ2

Ａ7

Ａ1

Ａ6

Ａ4

Ａ8

C5

C3

C3 C1C2

C6

C7

C4

C8

1.5mmx155mmCarbon Rod

C2C1

C7

W10

W9W71.5mmx347mm

Carbon Rod

W11

W43W3

W6

W18

W36

W37

W7

W39W40

W34W29

W34 W29

W30W30

W30

W29

W29

W29W42

W41W29

W29W30

W39-1

W21

W22

W6

W12

W13

W2W4

W3

W1

Outer：6x50mm Carbon TubeInner：3x98mm Carbon Tube

Install the aileron onto the upper wing by paper hinges.

3. Assemble the upper wing

1.Assemble the Fuselage 2.Assemble the wing of landing gear

3.1. Assemble the Aileron

BALSA WOOD AIRPLANEInstruction Manual

F25F8

F10

F11 F30

F32

F8

F9

F4F48

F35

F33

F26

F47

F23F1F22

F29

F34

F28

F2

F8-1

SpecificationWingspan：770mmLength：630mmNet weight：≈650g

Suggested EquipmentMotor： 2212 800-1000KVESC：20AServo：2.5g *2 & 5g *2 Propeller：7-8 inchBattery：2-3S 1300-1800mAh Radio≥3CH

W11

W14

W15

W7W6

W35W31

W31

W31

W31

W49

W57

W51

W52

W57

W29

W29

W29

W29

W29

W29

W29 W47

W48W46

W44W45

W7

W23

W20

W33

W32

W19

W29 W28W9

W10 W7

Inner：6x37mm Carbon Tube

Outer：3x77mm Carbon Tube

1.5mmx327mmCarbon Rod

W11

W10

W9

W8

W36W29

W29

W29

W29

W29

W29

W29

W29

W29

W55

W31

W31

W31W31

W31

W31

W56

W54

W25W24

W53

W26

W7

W16

W17

W27W7

W58

W50W50

Inner：6x37mm Carbon Tube

Outer：3x77mm Carbon Tube

1.5mmx294mmCarbon Rod

T7

T2

T6

T5

T4

T3

T1

T10

T14 T15T15

T17

T20T20

T17

T16

T18T18T18 T18T19T19

T11 T11

T12 T12

T13 T13

6.2. Assemble the wing

6.3 Install the landing gear and wing of langing gear.

6.3.3 Assemble and install the wheel.

6.3.1 Install the landing gear onto the fuselage.

6.3.2 Assemble the wing of landing gear.

Insert the steel wire rod

6.4 Assemble the cowling and scale parts.

7.1 Assemble the motor and motor mounting base.7.2 Assemble the servo and push rod for aileron.

7.3 Assemble the elevator rudder.

7.4 Assemble the servo horn and push rod for elevator and rudder.

8. Adjust the C.G

6.2.1. Plug and assemble together the middle wing,then install onto the fuselage.

Fix the horizontal tail with glue.

Glue the reinforcing bar here. Assemble the vertical tail onto the fuselage by paper hinges.

6.2.3. Plug and assemble together the lower wing,then install onto the fuselage.

6.2.4. Connect the upper,middle and lower wing by aluminum rod (as▲marked)

6.1Install the horizontal and vertical tail onto the fuselage.

5.1. Assemble the horizontal tail

screw

screw

screw

screwscrew

▲Insert through the preserve slots and fix with glue.

screw

screw

screwscale machine gun

rubber ring//wind shield

scale engine

cowling

carbon rod

Carbon fiber strip+screw

wheel stopper

7. Assemble the power system

B3

B2

B4

Diagram for push rod inside the fuselage

4. Assemble the middle wing

5. Assemble the lower wing

5.2. Assemble the vertical tail

6. Assemble the other components

T8

T9

6.2.2. Plug and assemble together the upper wing,then install onto the fuselage by aluminum rod and fix with screws.

125mmC.G