28
Doc No. FM0411 issue J Page 1 Advent xt Warden Call System ______________________________________________________________________________________________________________ Programming Guide Tynetec operates a policy of continual product improvement and reserves the right to modify the specification of its products. If any variation to the details in this document are suspected please contact Tynetec’s Technical Support on 01670 352371. Tynetec, a business unit of Legrand Electric Ltd Unit 10 Cowley Road, Blyth Riverside Business Park, Blyth Northumberland, NE24 5TF. Tel: 01670 352 371 Fax: 01670 362 807 Email: [email protected] Web: www.tynetec.co.uk

FM0411 J-Advent xt Programming Guide - Tynetec...Doc No. FM0411 issue J Page 1 Advent xt Warden Call System Programming Guide Tynetec operates a policy of continual product improvement

  • Upload
    others

  • View
    4

  • Download
    0

Embed Size (px)

Citation preview

  • Doc No. FM0411 issue J Page 1 

    Advent xt  Warden Call System  

    ______________________________________________________________________________________________________________ 

         

       Programming Guide  

         

                        

    Tynetec operates a policy of continual product improvement and reserves the right to modify the specification of its products.   

    If any variation to the details in this document are suspected please contact Tynetec’s Technical Support on 01670 352371.

            

    Tynetec, a business unit of Legrand Electric Ltd Unit 10 Cowley Road, Blyth Riverside Business Park, Blyth 

    Northumberland, NE24 5TF. Tel: 01670 352 371 Fax: 01670 362 807 Email: [email protected]  Web: www.tynetec.co.uk 

  • Doc No. FM0411 issue J Page 2 

      INDEX    

    SECTION  TOPIC PAGE  

    1  SLIP Interface Set‐up 32  Data Back‐up/Restore Function 33  To Enter/Exit Program Mode 44  System Defaults 55  Speech Defaults 66  Remote Trigger Defaults 77  Alarm Type Routing Defaults  88  General Set‐up 99  Tenants Unit Identity 1010  Tenants Unit Volume 1111  Tenants Unit Messages 1212  Custom Speech Messages 1 ‐ 128 1313  Custom Speech Messages 129 ‐ 256 1414  Tenants Unit Alarms 1515  Device Location Codes 1616  DTMF Relays 1717  Local Offsite Set‐up 1818  Remote Offsite Set‐up 1919  System Timers 2020  Audio & Data Set‐up 2121  Tunstall Protocol 2222  System Fault Codes 2323  Door Entry Set‐up  2524  Zoning Set‐up  2625  Alarm Type Routing  2726  IP & SIP Setup  28 

                 

               

  • Doc No. FM0411 issue J Page 3 

     1. SLIP INTERFACE SET‐UP  The Advent xt system is programmed using a Laptop PC connected to the main CPU board via a standard 9 pin male/female serial data cable (Tynetec Part No. EH0190). If the Laptop does not have a 9 pin serial port then a USB‐serial converter will be required (Tynetec Part No. W01150).   

    The Laptop must have a Windows 98, 2000 or Xp Operating System with its Serial Port configured for “Serial Line Interface Protocol” (SLIP). A separate manual is available (Tynetec Doc No. FM0446) detailing the set‐up of a SLIP interface on Windows 98 & Xp operating systems.   

    For Laptops with Windows 7 there is a Microsoft application available that runs Windows 7 in Xp mode thereby allowing the SLIP connection to work. Note: this application is only compatible with 64 bit Windows 7 professional, Enterprise or Ultimate Editions. Contact Tynetec’s Customer Support Dept for a copy of the software and the instruction guide (Tynetec Doc No. FM0692).  Advent xt Firmware  

    The programmable features described in this manual are only available if the Advent xt Controller has the following A00380 motherboard PCB issues and firmware versions (or later);    

    Firmware No.  Function  A00380 PCB Issue Firmware Version 

    A00380 PCB Issue 

    Firmware Version 

     

    EE1600  Main Processor  A‐G  V3.01A  H  V4.04A EE1605  Co‐Processor  A‐G V3.00B H V4.00A EE1610  Digital Speech Processor  A‐G  V3.00A  H  V4.01A 

     Contact Tynetec’s Customer Support Department for details of latest upgrades available.    

     2. DATA BACK‐UP/RESTORE FUNCTION  All system programming can be stored on a removeable 32MB Data Flash Card (Tynetec P/No. A00480) provided the controller has an A00380 issue “C” motherboard with V2.0 firmware onwards. The Flash Card should be left in the controller at all times so all changes are stored.  

    Data can be backed‐up manually using special codes via the Managers handset (default) or automatically every time changes are made. See the General Setup page to Enable Auto Back‐up.  Automatic Back‐up  

    This will occur every time you exit programming mode ‐ it can take up to 10 seconds to copy all the system data to the card. Radio devices are also automatically stored on the card as devices are added or removed.  Manual Back‐up  

    Press the RESET button on the controller motherboard, you have 60 seconds to use the following codes via the Managers handset (onsite mode only);  

    8010Copy all system configuration data and special messages to the Flash Card   

    8020Copy all radio device data to the Flash Card  Manual Restore  

    If the controller motherboard is replaced for whatever reason, data can be restored from your existing Flash Card onto the new board.   

    Fit the new motherboard, plug‐in your existing Flash Card, power‐up and press the RESET button. You have 60 seconds to use the following codes via the Managers handset (onsite mode only);  

    9010Transfer system configuration data and special messages from Flash Card to system memory  

    9020Transfer radio device data from Flash Card to system memory         

  • Doc No. FM0411 issue J Page 4 

     3. TO ENTER/EXIT PROGRAM MODE  To Enter Advent xt Programming Mode  

    Connect a Laptop PC (with a SLIP interface set‐up) to the main CPU local programming port CON1 using a serial data cable (Tynetec P/No. EH0190).  Double click on the Internet Explorer icon.  Make sure the SLIP Connection is selected in the Dial‐up Connection window and then click on Connect.  The main programming window will open as below;  

      Click on the System menu and record details about the installation and maintenance company.  Click on the Programming menu and select the mode required from the list.  Click on the Diagnostics menu to view details of all calls.  To Exit Advent xt Programming Mode  

    Close Internet Explorer by clicking on the cross in the top right corner.  If a disconnection box appears click on “disconnect” otherwise right click on the connection icon in the task bar and click on disconnect. Unplug the serial data cable from the Advent xt controller and test the system.                     

  • Doc No. FM0411 issue J Page 5 

     4. SYSTEM DEFAULTS  From the Programming menu, select “System Defaults” if you want to restore all factory settings;  

       Click “Submit” to load system defaults.  This will clear all programming except custom speech messages and radio triggers.                                 

  • Doc No. FM0411 issue J Page 6 

     5. SPEECH DEFAULTS  From the Programming menu, select “Speech Defaults” if you want to restore all factory speech settings;  

       Click “Submit” to load speech defaults.  This will clear all custom speech messages leaving all other programming unaffected.                                 

  • Doc No. FM0411 issue J Page 7 

     6. REMOTE TRIGGER DEFAULTS  From the Programming menu, select “Remote Trigger Defaults” if you want to clear all radio triggers devices from the system;  

      Click “Submit” to load remote trigger defaults.  This will clear all radio trigger devices leaving all other programming unaffected.                                  

  • Doc No. FM0411 issue J Page 8 

     7. ALARM TYPE ROUTING DEFAULTS  From the Programming menu, select “Alarm Type Routing Defaults” if you want to set all alarm types back to report in the current operating mode;                               Click “Submit” to load alarm type routing defaults.  Any alarm types that were set to report in a specific operating mode will be cleared.                            

  • Doc No. FM0411 issue J Page 9 

     8. GENERAL SET‐UP  From the Programming menu, select “General Set‐up” to set the system type, number of network devices, enable PBX and all call/fire tone features;    Enter the following;  

    System Type: choose standard Advent xt = 01.  

    Subunits: set the total number of intercom units on the site,  01 to 255 (includes Lift units and Manager units ‐ but not digital door panels).  

    Subunit Fault Report: must be 01 for normal operating mode. Only set to 00 during installation to turn intercom fault monitoring off (ie. if radio pendant coverage is required before the intercoms are fitted).  

    Network Receiver Units: set the total number of network receivers (standard + zoned) on the site; 00 to 16 (00 = none). See the Zoning Set‐up page to enable zoned network receivers (max 12 per site).  

    Network Exchange Units: must be 00 for Talkswitch/Fortivoice (i.e. Kirk DECT). Only set to 01 for Panasonic PBX with BT Diverse DECT.  

    Network Keyswitch Units: 00 = not fitted or 01 to enable a Status Module.   

    PBX Ring Enable: 00 = no PBX or 01 if Talkswitch/Fortivoice/Matrix is fitted.  

    All Call Enable: 00 = no All Call or 01 if All Call fitted.  

    Fire Tone Enable: 00 = no Fire Tone sounded through intercoms, 01 = Fire Tone enabled.  

    BT Line Monitor Enable: 00 = BT line monitoring disabled or 01 = BT line monitoring enabled.  

    Warden Attack Alarm: 00 = disabled. If attack pendants or panic buttons are being used then the method of reporting these alarms must be set; 01 = onsite, 02 = local offsite, 03 = remote offsite.  

    Auto Back‐up Enable: 00 = manual back‐up enabled or 01 = automatic back‐up enabled. All system configuration data and radio devices can be stored on the controller Flash Memory Card.  

    Park Character 5, 8 or 9: 5F = onsite park enabled (single 5 to park), change to 55 (for double 5 to park), or 8F/88 or 9F/99.  FF = onsite park disabled.  

    Onsite Ring Cycle Enable: 00 = Kirk (or BT) base station or 01 = Distybase ONLY  

    Duty Change Alarm Enable: 00 = normal, 01 = automatic call control centre when system is switched between onsite/remote offsite and vice versa.  

    Onsite DTMF Decode Mode: 01 = normal, 00 = Geemark Jupiter Desk Telephone Only  

    Manager Panel Enable: default 00 = Manager Panel disabled, set to 01 if a Manager’s Panel is connected.  

    DECT Disconnect Enable: default 01 for Fortivoice IP PBX (i.e. drop line before ring to reset), 00 for no reset before ring.  

    Priority Alarm Type: default FF for no alarm type priority (i.e. alarms reported in the order they are received), or enter the Tynetec code of the alarm type you want to take priority (e.g. 43 = smoke alarms). See list of Tynetec codes on page 15.   

    Click “Submit” to enter any changes.   

  • Doc No. FM0411 issue J Page 10 

     9. TENANTS UNIT IDENTITY  From the Programming menu, select “Tenants Unit Identity” to program the flat numbers to the intercoms;  

      Enter the flat numbers in the boxes provided (numeric only).  

    Add Lift/Manager callpoint ID’s after the flat numbers (if applicable).  

    Finally add digital door panel ID’s (if applicable).  It is recommended that the digital door panel ID’s run sequentially from 600 to 615 (door 1 to Door 16). Other ID’s can be used e.g. Anchor Housing 704 (front door) & 705 (rear door).  The number of digital door panels must be set in the “Door Entry Set‐up” menu ‐ see page 24.  Custom speech messages should be created to identify door panel locations ‐ see page 12.  

    Leave unused channels set as FFFF.  

    Click “Submit” to enter any changes.  

    Click “Next” to view the next page of ID’s (65 ‐ 128) etc.                        

  • Doc No. FM0411 issue J Page 11 

     10. TENANTS UNIT VOLUME  From the Programming menu, select “Tenants Unit Volume” to set the default volume level for each intercom;                             Enter the volume level for each flat; 00 = mute to 04 highest.  

    Leave unused channels set as default 02.  

    Click “Submit” to enter any changes.  

    Click “Next” to view the next page of ID’s (65 ‐ 128) etc.                             

  • Doc No. FM0411 issue J Page 12 

     11. TENANTS UNIT MESSAGE  From the Programming menu, select “Tenants Messages” to set custom speech messages for each intercom;  

       A custom speech message can be created for any intercom or door panel by entering numbers from the tables on the following pages (max 8 words per flat).   

    For no custom speech message leave all boxes set as 00.  

    Click “Submit” to enter any changes.  

    Click “Next” to view the next page of ID’s (16 ‐ 32) etc.                             

  • Doc No. FM0411 issue J Page 13 

     12. CUSTOM SPEECH MESSAGES 1‐128    

    MESSAGE NUMBER  SPEECH MESSAGE 

    MESSAGE NUMBER SPEECH MESSAGE 

     

    1  One  65 Incorrect Entry2  Two  66 Please Try Again3  Three  67 Time4  Four  68 Date5  Five  69 Start Time6  Six  70 Stop Time7  Seven  71 Please Enter8  Eight  72 Intruder Mode9  Nine  73 Activity Mode10  Ten  74 Day and Year11  Eleven  75 Client Wandering12  Twelve  76 Enuresis13  Thirteen  77 Enable14  Fourteen  78 Disable15  Fifteen  79 Telephone Number16  Sixteen  80 Onsite Mode17  Seventeen  81 Remote Offsite Mode18  Eighteen  82 Local Offsite Mode19  Nineteen  83 Pill Dispenser20  Twenty  84 Bed Occupancy21  Thirty  85 Network22  Fourty  86 Receiver23  Fifty  87 PBX24  Sixty  88 Interface25  Seventy  89 Keyswitch26  Eighty  90 Door Panel27  Ninety  91 Message28  Hundred  92 Please Wait29  Thousand  93 Office30  Zero  94 Wardens31  And  95 Scheme Manager32  Short Circuit  96 Front33  Intercom  97 Rear34  Pendant  98 Corridor35  Pullcord  99 Common Room36  Smoke  100 Lounge37  Open Circuit  101 Guest Room38  Activity  102 Bungalow39  Intruder  103 Toilet40  System  104 Lift41  Alarm  105 Shower42  Fault  106 North43  Low Temperature 107 East44  High Temperature 108 South45  Inactivity  109 West46  Gas  110 Emergency Lights47  Parked  111 Library48  Carbon Monoxide 112 Hobby49  Remote Trigger Low Battery 113 Hairdresser50  Ready  114 Telephone51  Fail  115 Dining52  Site  116 Area53  Fall  117 Laundry54  Flat  118 Gents55  System 24 Volt Fuse Blown 119 Ladies56  Flood  120 Bathroom57  System Battery Low 121 Lobby58  System 12 Volt Fuse Blown 122 Foyer59  System Mains Fail 123 Stairs60  System Mains Restored 124 Bedroom61  System BT Line Fault 125 Assistant62  System BT Line Restored 126 Kitchen63  Fire Alarm  127 Keysafe64  Enter  128 Control Rack

        

  • Doc No. FM0411 issue J Page 14 

     13. CUSTOM SPEECH MESSAGES 129‐256    

    MESSAGE NUMBER  SPEECH MESSAGE 

    MESSAGE NUMBER SPEECH MESSAGE 

     

    129  Bin Store  193 Attic130  Boiler  194 Living131  Quiet Room  195 Shed132  Conservatory  196 Entrance133  Sequence  197 Up134  Door  198 Down135  House  199 Study136  Manager  200 Ground137  Test  201 Movement Sensor138  Room  202 Telehealth139  Games  203 Intercom Faults140  T.V.  204 System faults141  Staff  205 Weekend142  Meeting  206 Door Contact143  A  207 Boundary144  B  208 Chair Occupancy145  C  209 Electrical Monitoring Unit146  D  210 Tamper147  E  211 Tenants Check148  F  212 No Response149  Gate  213 Zone150  Community Room 214 Offsite151  Cooker Isolated 215 RSSI152  Auxiliary  216 Print‐out153  Changing  217 Attenuation Value154  Drugs Cabinet  218 Annunciate155  First  219 Mode156  Second  220 Tenant OK157  Third  221 Plant158  Fourth  222 Internal159  Fifth  223 Minutes160  Sixth  224 Away Mode161  Reception  225162  I.T.  226163  Computer  227164  Wheel Chair  228165  Fire Exit  229166  Floor  230167  Smoking  231168  Shop  232169  Physiotherapy  233170  Fitness  234171  Privacy  235172  Transfer  236173  Busy  237174  Test Mode  238175  Epilepsy  239176  Attack  240177  Bathroom Occupancy 241178  Back Up  242179  Location Code  243180  Hallway  244181  Landing  245182  Garage  246183  Workshop  247184  Outbuilding  248185  Garden  249186  Local Unit  250187  Ulility  251188  Heat  252189  Radio Device  253190  Redirect  254191  Basement  255192  Cellar  256

        

  • Doc No. FM0411 issue J Page 15 

     14. TENANTS UNIT ALARMS  From the Programming menu, select “Tenants Unit Alarms” to set the 4 hardwired alarm input types on each intercom. Note; these inputs are only available on intercoms without a telephone connected.  

    The 4 programmable inputs are shown on the web page in the following order:  

     

    INPUT 1 (47K on terminal 19) default 42 = Low Temp  

      

     

    INPUT 2 (18K on terminal 19) default 34 = Door Exit 

      

     

    INPUT 3 (47K on terminal 18) default 44 = Gas 

      

     

    INPUT 4 (18K on terminal 18) 

    default 49 = CO   

     All input devices must provide N/O clean contacts which close on alarm. Use the contacts to switch 0V with the correct value (18K/47K) series resistor.                              Enter the Tynetec Code for each device type from the list below;  12 = Ceiling Pullcord 30 = Inactivity Alarm (PIR) 33 = Bed Occupancy Alarm 34 = Door Exit (default INPUT 2) 41 = High Temperature Sensor 42 = Low Temperature Sensor (default INPUT 1) 43 = Smoke Detector 44 = Gas Detector (default INPUT 3) 48 = Heat Detector 49 = Carbon Monoxide Detector (default INPUT 4) 50 = Intruder Alarm (PIR) 80 = Flood Detector  Click “Submit” to enter any changes.      

  • Doc No. FM0411 issue J Page 16 

     15. DEVICE LOCATION CODES  From the Programming menu, select “Device Location Codes” to set the location in the dwelling where each input device is located. The 8 programmable locations per flat are entered in the following order:  

    Intercom Unit 

    Ceiling Pullcord 

    Smoke Detector 

    PIR Detector 

    Input 1 (Low Temp) 

    Input 2 (Door Exit) 

    Input 3 (Gas) 

    Input 4 (CO) 

     Note; the last 4 locations (I/P 1‐4) are only available on intercoms without a telephone connected.                              

    Device Location Codes can range from 00 to 99 ‐ see list below;  

    00  Not Assigned  20  Toilet (downstairs) 40 Common Room (main) 01  Local Unit  21  Toilet (other) 41 Common Room (other) 02  Hallway (downstairs)  22  Kitchen (main) 42 Lift (main)03  Hallway (upstairs)  23  Kitchen 2 43 Lift 204  Stairs (main)  24  Kitchen Area (other) 44 Lift (other)05  Stairs (2nd)  25  Utility Room (main) 45 Front Gate06  Landing  26  Utility Room (other) 46 Rear Gate07  Bedroom 1 (master)  27  Entrance/Lobby 47 Outbuilding (main)08  Bedroom 2  28  Front Door (main) 48 Shed09  Bedroom 3 (other)  29  Front Door (other) 49 Outbuilding/Shed 10  Bedroom 4 (guest)  30  Back Door (main) 50 Garden (front)11  Living Room (main)  31  Back Door (other) 51 Garden (rear)12  Living Room 2  32  Garage (main) 52 Garden (other)13  Living Area (other)  33  Garage (other) 53 Basement/Cellar14  Dining Room (main)  34  Workshop 54 Ground Floor15  Dining Room 2  35  Laundry (main) 55 Bin Store16  Dining Area (other)  36  Laundry (other) 56 Boiler Room17  Bathroom (main)  37  Office (main) 57 Attic18  Bathroom 2  38  Study/Office (other) 5819  Toilet (upstairs)  39  Games Room 59

     Location Voice Reporting; default = 01 for onsite /local offsite speech message. 00 to disable.  Click “Submit” to enter any changes.    

  • Doc No. FM0411 issue J Page 17 

     16. DTMF RELAYS  From the Programming menu, select “DTMF Relays” to set the DTMF characters used to activate the system relay outputs and the time duration each output remains energised;  

       Enter the following;  Subunit DTMF Char: enter the DTMF key used to activate the relay in an intercom during speech, default = 03, can be changed to 04, 07, 08 or 09 only.  

    Subunit Relay Time: set the time for which the intercom relay remains energised, 01 to 99 seconds.  

    DTMF Char Channel 001: leave as FF and output relay 1 will activate for the duration of any alarm, or enter the DTMF key used to activate output 1 ‐ can be set to 03, 04, 07, 08 or 09 only.   

    DTMF Char Channel 002: leave as FF and output relay 2 will energise for the same duration input 4 is activated (used to release the door lock with Fire Alarm input), or enter the DTMF key used to activate output 2 ‐ can be set to 03, 04, 07, 08 or 09 only.   

    DTMF Char Channel 003: leave as FF and output relay 3 will control the BT Line Selector (ZXT330) when enabled on the “Remote Offsite” screen, or enter the DTMF key used to activate output 3 ‐ can be set to 03, 04, 07, 08 or 09 only.   

    DTMF Char Channel 004: leave as FF and output relay 4 will energise for the duration of a BT Line Fault, or enter the DTMF key used to activate output 4 ‐ can be set to 03, 04, 07, 08 or 09 only.   

    Relay Time Channel 001: enter the time for which the controller output relay 1 remains energised if set as a DTMF character, default = 10, can be 01 to 99 seconds.   

    Repeat as above for Relay Times on Channels 002, 003 & 004.  Click “Submit” to enter any changes.             

  • Doc No. FM0411 issue J Page 18 

     17. LOCAL OFFSITE SET‐UP  From the Programming menu, select “Local Offsite Set‐up” to set the dial attempts and up to 6 telephone numbers for Local Offsite mode;     Enter the following;  Dial Attempts: enter the number of times each number will be dialled if not answered, default 03, can be changed from 01 to 06.  

    Park Character 5, 8 or 9: 5F = local offsite park enabled (single 5 to park), change to 55 (for double 5 to park), or 8F/88 or 9F/99.  FF = local offsite park disabled.  

    GSM Line Enable: 00 = disabled. Set to 01 if a Burnside GSM base station is being used instead of a land line.  

    Telephone Number 001: enter the Local Offsite telephone number ‐ 2 digits per box.  

    Repeat for up to 6 Local Offsite telephone numbers.  

    Leave unused telephone number locations set as FF.  

    Click “Submit” to enter any changes.  Note; the numbers will be dialled in sequential order unless a specific order is set via the DECT handset ‐ see the Operators Manual (Tynetec Doc No. FM0420).                  

  • Doc No. FM0411 issue J Page 19 

     18. REMOTE OFFSITE SET‐UP  From the Programming menu, select “Remote Offsite Set‐up” to set the protocol type, dial attempts, site ID, park character, audio switching mode and up to 3 telephone numbers for Remote Offsite mode;                              Enter the following;  Protocol Type*: choose what data format the control centre uses, TT New = 01, BS7369 = 02, BS8521 = 03 and TT92 = 04.  

    Dial Attempts: set the number of times each number will be dialled if not answered, default 03, can be changed from 01 to 06.  

    Site Identity: enter the unique site identity number issued by the control centre, max 4 digits.  

    Park Character: default FF = remote offsite park disabled. If required; set the DTMF character used by the control centre to park faulty intercoms, normally  05 (can be 00 to 09).  

    Audio Vox Enable: simplex = 01 (default) or Vox = 02. Simplex means speak/listen control is toggled manually by the operator, Vox is automatic (voice switched).   

    Telephone Number 001: enter the Remote Offsite telephone number ‐ 2 digits per box.  

    Repeat for up to 3 Remote Offsite telephone numbers.  

    Leave unused locations set as FF.  

    Secondary BT Line Enable: normally set to 00. Only set to 01 if the Advent xt system has 2 BT lines connected (main and secondary) via a BT Line Selector Unit (P/No. ZXT330). If set to 01 the DTMF channel 003 must be set to FF on the “DTMF Channels” screen.  Click “Submit” to enter any changes.  *Note: Protocol Types TT New = 01 and BS7369 = 02 were removed in V4.01A firmware (21 April 2017) and re‐instated in V4.04A firmware (23 February 2018) onward.          

  • Doc No. FM0411 issue J Page 20 

     19. SYSTEM TIMERS  From the Programming menu, select “System Timers” to set the time‐out periods for calls in all operating modes and the repeat time for Extracare intercoms;                            Enter the following;  Onsite Timeout: the maximum time a call can remain unanswered in onsite mode before being automatically switched offsite, default = 0360, can be changed from 0001 to 9999 seconds.  

    Onsite Audio Timer: the maximum speech time for a call in Onsite mode, default = 0360, can be changed from 0001 to 9999 seconds.  

    L‐Offsite Hold Timer: the maximum time a Local Offsite call will wait to be answered, default 0050, can be changed from 0001 to 9999 seconds.  

    L‐Offsite Audio Timer: the maximum speech time for a call in Local Offsite mode, default = 0120, can be changed from 0001 to 9999 seconds.  

    R‐Offsite Hold Timer: the maximum time a Remote Offsite call will wait to be answered, default 0050, can be changed from 0001 to 9999 seconds.  

    R‐Offsite Audio Timer: the maximum speech time for a call in Remote Offsite mode, default = 0360, can be changed from 0001 to 9999 seconds.  

    R‐Offsite Callback Timer: the maximum speech time when a control centre calls a resident back in Remote Offsite mode, default = 0360, can be changed from 0001 to 9999 seconds.  

    Dial in Line Hold Timer: the maximum time the system will wait between a control centre ringing‐in and calling a resident back in Remote Offsite mode, default = 0360, can be changed from 0001‐ 9999 secs.  

    BT Line Fault Timer: the delay before telephone line fault is reported, default = 120, can be changed from 0001 to 9999 seconds  

    Extracare Repeat Time: the maximum time between cancelling an Extracare call via the DECT handset and visiting the intercom to perform a manual reset, default 15 mins, can be changed from 01‐30 mins.  

    BS7369  (mS): 0600 delay between data packets for 21CN compatibility on BS7369 protocol. Not used in V3.01A/V4.01A onwards.  

    Onsite Duty Start Time: FFFF = disabled, enter time for the system to automatically select onsite mode. Use 24 hour clock and enter leading zero’s, eg. 0800 (8 AM).  

    R Offsite Duty Start Time: FFFF = disabled, enter time for the system to automatically select remote offsite mode. Use 24 hour clock and enter leading zero’s, eg. 1700 (5 PM).  

    Click “Submit” to enter any changes.   

  • Doc No. FM0411 issue J Page 21 

     20. AUDIO & DATA SET‐UP  From the Programming menu, select “Audio/Data Set‐up” to set the BT line gain and volume levels;  

       Enter the following;  BT Tone TX Gain: the gain of tones to line, default = 01, can be changed from 00 to 02. Only change when advised by Tynetec.  

    Vox Sensitivity Level: the audio signal level at which voice switching occurs, default = 01, can be changed from 00 to 02. Only change when advised by Tynetec.  

    Volume to Onsite Warden: default = 02, enter the audio to warden volume level during onsite mode,  01 lowest to 03 highest.  

    Volume to Offsite Warden: default = 02, enter the audio to warden volume level during either offsite mode, 01 lowest to 03 highest.  

    PA Volume Onsite: default = 02, enter the All Call speech volume when activated during Onsite mode, 01 lowest to 03 highest.  

    PA Volume Offsite: default = 02, enter the All Call speech volume when activated during either Offsite mode, 01 lowest to 03 highest.  

    Fire Tone Volume: default = 02, enter the All Call Fire Tone volume, 01 lowest to 03 highest.  

    Offsite Status Tones: default = 01 to enable, 00 to disable. Only disable when advised by Tynetec.  Click “Submit” to enter any changes.                 

  • Doc No. FM0411 issue J Page 22 

     21. TUNSTALL PROTOCOL  From the Programming menu, select “Tynetec to TT New Alarm Codes” to set‐up a conversion table for Tynetec Codes to Tunstall DTMF characters. Not used in V3.01A/V4.01A onwards.                               Enter the TT92 codes which the control centre requires in the box alongside the relevant Tynetec Code 000 to 099.  

    TT92 Codes; 00 = auxiliary alarm, 01 = intercom integral button, 02 = pullcord/pendant, 03 = smoke,  04 = equipment fault, 05 = low battery (pendant/sensor), 06 = environmental alarm, 07 = inactivity, 09 = intruder, 15 = speech unit fault  Click “Submit” to enter any changes.                         

  • Doc No. FM0411 issue J Page 23 

     22. SYSTEM FAULT CODES  From the Programming menu, select “System Fault Identities” to set the codes which report system faults;                              Note, these codes will NOT normally need to be changed;  System Fault Code 001: Mains Restored, default 4798 System Fault Code 002: Mains Failed, default 4799 System Fault Code 003: Low Battery, default 4793 System Fault Code 004: 12V/24V Fuse Blown, default 4794 System Fault Code 005: Not Used, default 4795 System Fault Code 006: Fire Alarm Activated, default 3999 System Fault Code 007: BT Line Failed, default 4797 System Fault Code 008: BT Line Restored, default 4796 System Fault Code 009: Daily Alarm, default 4785 System Fault Code 010: Not Used, default 0000  Duty Change Code 001: default 4901 = switched to onsite mode  

    Duty Change Code 002: default 4902 = switched to remote offsite mode  Click “Submit” to enter any changes.  

    Click “Next” to view Network Receiver Fault Codes, default 4800 to 4815.  

    Click “Next” to view Network PBX Interface Fault Codes, default 4816 to 4823.  

    Click “Next” to view Network Status Module Fault Codes, default 4824 to 4827.  

    Click “Next” to view Network Door Panel Fault Codes, default 4828 to 4843.          

  • Doc No. FM0411 issue J Page 24 

     23. DOOR ENTRY SET‐UP  From the Programming menu, select “Door Entry Set‐up” to set the number of door panels, speech/lock timers, access codes, trade times, call transfer on/off time period, print‐out enable and fast busy;      Enter the following;  

    Number of Door Panels: enter the total number of digital door panels, 00 = none to 16 = max.  Note; digital door panels have fixed ID’s from 600 to 615 (door 1 to Door 16) ‐ these must be entered after the flat numbers in the “Tenants Unit Identity” menu. See page 9 of this manual.   

    BST Adjustment: default = 01 for automatic adjustment of daylight saving time, 00 = no adjustment.  

    Speech Time: enter the maximum speech time for a door entry call, default 60 seconds, can be changed from 0000 to 0255 seconds. (Timer terminated after lock release or phone hung‐up).  

    Lock Time: enter the maximum lock release time, default 10 seconds, can be changed from 0000 to 0255 seconds. (Timer terminated when door opened if door status contact is connected).  

    Privacy Time: enter the telephone privacy time, default 60 minutes, can be changed from 0000 to 0999 minutes (0000 = on/off privacy).  

    Access Code 001 to 004: enter access codes 1 to 4, default FFFF = disabled, any 4 digit number.  

    Ring Cycles: enter the number of telephone ring cycles before the digital door panel displays “Not Available ‐ Please Try Later”. Default = 08, can be changed from 00 to 99.  

    Door Open LED Enable: default = 01 to illuminate the green door open LED on all telephones when the door is opened (must have door status contact fitted). 00 disables the green door open LED.  

    Timed Coded Access Enable: default = 00 disables timed access codes (ie. codes will operate any time). 01 allows access codes to function during specific time periods only.  

    Timed Access Code 001 to 004: enter timed access codes 1 to 4, default FFFF = disabled, any 4 digit number. See below for setting the time periods these codes can be used.  

    Access Code On Time 001 to 004: enter up to 4 on times per day using 24 hour clock format and enter leading zero’s, eg. 0700, 1300, 1630. Default FFFF = disabled  

    Access Code Off Time 001: enter up to 4 off times per day using 24 hour clock format and enter leading zero’s, eg. 0700, 1300, 1630. Default FFFF = disabled  

    Trade On Time 000 to 020: enter up to 3 on times per day, 000‐002 = Monday, 003‐005 = Tuesday etc. Default FFFF = disabled, use 24 hour clock and enter leading zero’s, eg. 0700, 1300, 1630.   

  • Doc No. FM0411 issue J Page 25 

     23. DOOR ENTRY SET‐UP ‐ CONTINUED                               Trade Off Time 000 to 020: enter up to 3 off times per day, 000‐002 = Monday, 003‐005 = Tuesday etc. Default FFFF = disabled, use 24 hour clock and enter leading zero’s, eg. 0700, 1300, 1630.  

    Note; trade on and off times must be within the same day; 0000 to 2359.  

    Call Transfer Time On: default FFFF to allow door entry calls to be made 24 hours/day. To disable calls during evening/night enter call transfer start time using 24 hour clock eg. 2000 (8 PM).    

    Call Transfer Time Off: default FFFF to allow door entry calls to be made 24 hours/day. To disable calls during evening/night enter call transfer end time using 24 hour clock eg. 0800 (8 AM).  

    Door Entry Print Enable: default = 01 to print all door entry call activity, 00 disables door entry printing.  

    Fast Busy On/Off Enable: default = 01 sends global “busy” command for use with door panel firmware EE0640 V3.00A onwards. Must be set to 00 for earlier versions of door panel firmware.   Click “Submit” to enter any changes.                    

  • Doc No. FM0411 issue J Page 26 

     24. ZONING SET‐UP   From the Programming menu, select “Zoning Set‐up” to enable zoned calling and zoned network receivers;  

    Zoned calling allows each intercom to call different extensions during the day/night. Zoned calling is only possible with a Panasonic KX‐TDA30 PBX. For details on Panasonic programming please contact Tynetec’s Customer Support Dept.  

    Zoned Network Receivers (NTR’s) allow the Advent xt system to identify the area of the building where a radio pendant has been activated. A maximum of 12 zoned NTR’s can be fitted per site.        Enter the following;  

    Zoning Enable: 00 = zoned calling disabled, 01 = zoned calling enabled.  

    Night Time Start Time: FFFF to disable. Enter night time start time using 24 hour clock eg. 2200 (10 PM).  

    Night Time Stop Time: FFFF to disable. Enter night time stop time using 24 hour clock eg. 0600 (6 AM).  

    Radio Zoning Enable: 00 = zoned NTR’s disabled, 01 = zoned NTR’s enabled.  

    Radio Zoning Print Enable: No Function (printing is enabled/disabled using telephone code 7004)  

    NTR Id Zone 001 ‐ NTR Id Zone 012: Enter the ID’s of zoned NTR’s only*  

    *Note; standard NTR’s and zoned NTR’s must be set‐up with unique ID’s starting from 01 and running sequentially to a max of 16.  A max of 12 zoned NTR ID’s are entered here and the total number of NTR’s fitted on site must be entered on the General Set‐up page. The difference between the total number of NTR’s and the number of zoned NTR ID’s entered here determines the number of standard NTR’s on the system.   Click “Submit” to enter any changes.          

  • Doc No. FM0411 issue J Page 27 

     25. ALARM TYPE ROUTING   From the Programming menu, select “Alarm Type Routing” to set the mode in which each different alarm type is reported.  

                                 Enter the following;  

    Tynetec Code XXX: FF = default operating mode, 00 = onsite mode, 01 to 06 = local offsite telephone number, 07 to 09 = remote offsite telephone number.  

    Note; if a call remains un‐answered in the set mode the Advent xt will revert to the default operating mode and dial sequence.  Tynetec Codes  000 = Oximeter      036 = Epilepsy      059 = Man Down 001 = Blood Pressure    037 = Bathroom Occupancy    060 = Keyswitch/NTR Failure 002 = Weight      038 = Chair Occupancy    063 = Mains Power Failure 003 = Blood Glucose    039 = Heart Rate      064 = System Power Supply Fault 011 = Intercom Alarm    041 = High Temperature    065 = System Low Battery 012 = Ceiling Pullcord    042 = Low Temperature    069 = Mains Power Restore 020 = Personal Pendant    043 = Smoke Detector    071 = Ceiling Pullcord Fault 022 = Fall Detector      044 = Gas Detector     073 = Intercom Fault 024 = Personal Attack    046 = Fire Alarm      074 = Telephone Line Failure 030 = Inactivity      048 = Heat Detector    075 = Telephone Line Restored 031 = Pill Dispenser     049 = CO Detector      080 = Flood Detector 032 = Enuresis      050 = Intruder      092 = Carer Attendance 033 = Bed Occupancy    051 = Electric Usage Monitor 034 = Door Exit      058 = Door Open  Click “Submit” to enter any changes.    

  • Doc No. FM0411 issue J Page 28 

     26. IP & SIP SETUP  From the Programming menu, select “IP & SIP Setup” to set the Digital Communicator/ARC IP Addresses and SIP Account details.  

      Enter the following;  

    IPv4 Address Details  

    The information below will need to be provided by the buildings IT Dept...  

    IP Address:  Sub Net Mask:  Gateway:  Primary DNS:  Secondary DNS:   SIP Account Details  

    The information below will need to be provided by the Alarm Receiving Centre (ARC)...  

    Description:  Display Name:  Primary Domain: Secondary Domain: Username:  Proxy Username:  Proxy Password:  Primary ARC Username:  Secondary ARC Username:  Primary Heartbeat Username:  Secondary Heartbeat Username:   Click “Submit” to enter any changes.  Notes:  

    1. the Site ID must still be entered on the Remote Offsite Setup page 2. if IP & SIP settings are entered the IP ARC will be the primary Remote Offsite contact 3. if the IP connection fails for whatever reason the PSTN ARC will be used as a secondary back‐up