Fiber Optic Products for Access Networkshexatronic.com/media/202200/fiber-optic-products-for...Fiber Optic Products for Access Networks Baltic Edition 2 HCI 28701-0008-A Passive fiber

Fiber Optic Products for Access Networks

Baltic Edition

http://www.hexatronic.com

2HCI 28701-0008-A

Passive fiber optic system solutions for Fiber To The Home – FTTH and Campus NetworksThis catalogue presents an overview of our Passive Fiber Infrastructure for Fiber To The Home and Campus Net-works. All products are designed and tested to meet the highest quality and environmental standards.

The catalogue covers the air blown fiber system Ribbonet® and the Hexatronic Micronet micro cable system is used for efficient installation of access networks including Fiber-to-the-Home (FTTH) and similar architectures.

For a more comprehensive selection of fiber optic system solutions, refer to the main catalogue Fiber Solutions for Access and Transport Networks or visit www.hexatronic.com

For immediate assistance with your queries, contact Hexatronic sales support: +46 (0) 10 - 453 02 00,[email protected]

Hexatronic Micronet and Ribbonet® – Flexible Fiber Optic Cable Systems for Broadband in Metropolitan and Access Networks

Online Catalogue

For the digital catalogue and more information about our products and services, please visit hexatronic.comHexatronic’s catalogues are also available online at issuu: issuu.hexatronicpartners.se


mailto:order%40hexatronic.com%20?subject=

3

Air Blown Fiber, Nano Cables and Micro Cables ..............................................................................................4

ApplicationsFiber To The Home ...............................................................6

Metro- and Campus Networks .............................................8

Business Access ....................................................................9

Fiber and Duct IdentificationFiber and Duct Identification ..............................................10

CablesMicro Cables .......................................................................11

Nano Cables .......................................................................11

Microducts for Direct Buried InstallationThick Walled Microducts, Single Tubes, 7/3,5 ....................12

Thick Walled Microduct Assemblies, 7/3,5 mm .................13

Thick Walled Microducts, Single Tubes, 14/10 mm ............14

Thick Walled Microduct Assemblies, 14/10 mm ................15

HDPE Ducts, 18/12 mm ......................................................16

Microducts for Installation in Exisiting ConduitsThin Walled Microduct Assemblies, 5/3,5 mm ...................17

Thin Walled Microducts, 12/10 mm ...................................18

Microducts for Indoor InstallationThin Walled Microduct Assemblies, 5/3,5 mm ...................19

Sealings, Connectors and End StopsDivisible Seals for Microducts, 5/3,5 and 7/3,5 mm ...........20

Divisible Seals for Microducts, 12/10,

14/10 and 18/12 mm ..........................................................20

Connectors for Thin Walled Ducts ......................................21

Connectors for Thick Walled Ducts ....................................21

Straight Connectors for Cable Ducts, 18 mm .....................21

End Stops for Thin Walled Ducts ........................................22

End Stops for Thick Walled Ducts ......................................22

Gas Block Connector 5 mm ...............................................22

Gas Block Connector 7-14 mm .........................................22

Training ............................................................................................23

CONTENTS

4

Air blown Fiber, Nano Cables and Micro Cables – The key to Success

Hexatronic Micronet and Ribbonet® ... Heatronic Micronet and Ribbonet® are flexible and cost-effective cabling systems for installation of optical fibers in all types of metropolitan and access networks. Built to last, they deliver unlimited bandwidth capacity as well as capacity to grow with user needs – and as new users are added.

Ribbonet® is Hexatronic´s established blown fiber and nano cable system, especially developed for access networks. When new users arrive, more optical fiber is simply blown into the existing channels, or ducts. Ribbonet’s® air blowing technique uses a patented handheld tool that reduces cable installation time to a minimum, compared to conventional techniques.

... the perfect complementsThe flexibility offered by air-blown technology is taken one step further – and into metropolitan networks – with Hexatronic´s Micronet system. One Ribbonet® fiber or nano cable contains from one up to 12 single fibers, whereas a single Micronet cable can hold up to 192 sing-le fibers. This supreme capacity potential makes Micro-net the preferred choice when installing metropolitan networks. Micronet is also a complement to Ribbonet®

in access networks, where future scalability is of utmost importance. In this case, Micronet is used for the first part of the access network, from the distribution node to intermediary splicing points, where Ribbonet® is used for the final section to the end users.

5

Why are Micronet and Ribbonet® more flexible than other systems?The ducts are installed separately and in advance, which means:• Installation of optical fiber may be incremental,

adapted to growth in end user demand.

• Unlike traditional cable pulling, the blown-in fiber is not affected by harsh treatment during installation.

• Minimization of splice points, which reduces installa-tion time.

• Easy network upgrade with more fiber or other types of fiber.

• Simplified network design.

The result is a future-proof network solution where ad-ditional bandwidth may be added at any time depen-ding on investment budgets and end user demand.

Micronet and Ribbonet® meet the demand for:• Nearly unlimited bandwidth, which creates a future-

proof network ready for tomorrow’s demanding applications.

• Cost-efficient roll-out and maintenance, which creates the opportunity for increasing broadband penetration and reaching out to new users.

Unique Micronet featuresMicronet is the most advanced micro cable solution on the market:• The micro cables’ minimal diameter enables multi-

fiber installation even in narrow channels.

• The minimal cable dimensions mean easy transport and handling.

• The Micronet cable is designed to maximize installa-tion lengths and to minimize cable jointing.

Unique Ribbonet® featuresRibbonet® is the most flexible and cost-effective fiber-blowing solution currently available on the market:• Hexatronic’s unique fiber-blowing tool is lightweight,

hand-held and easy-to-use and offers maximum pro-tection to the highly sensitive glass fiber. And with a capacity to blow up to 100 m of fiber per minute, it is also a whole lot faster than alternative methods.

• Pre-terminated fibers make installation of fiber from the end user faster and easier.

• The micro duct’s interior, with its innovative construc-tion design that reduces the friction between the fiber and the duct is designed to speed up the pas-sage of the fiber.

6

FIBER TO THE HOME

Applications

Fiber To The Home – Detached HousesFiber optic broadband connection of detached houses has never been so easy. With Hexatronic’s Micronet and Ribbonet® systems installation can be done at an un-beatably low cost.

An access node connecting the detached houses is placed in a suitable location near the premises and a point-to-point connection is established between each house and the acess node. Even though the installation of the entire fiber optic network is often not made at the same time in these types of areas, the whole area should be prepared with micro ducts in order to enable future fiber penetration and bandwidth increase.

Connection of the areas access nodes and links to a metropolitan network is preferably done using Hexatronic´s Micronet system. This makes for fast and easy network upgrades when more fiber is needed to connect new end users. Since Hexatronic Micronet and Ribbonet® can be co-located with existing power or water infrastructure, installation cost is further reduced.

Fiber optic connection of detached houses using Hexatronic´s Micronet and Ribbonet® systems gives a number of advantages:

Low initial investment cost• The solution means lower initial cost for optical fiber in-

stallation since fiber is only installed to paying end users.

• New end users are connected fast, easy and at low cost.

Flexibility• Combining Hexatronic Micronet and Ribbonet®

makes it easy to connect new end users. New fiber is simply installed in existing micro ducts using blown fiber or nano cables.

7

Fiber To The Home – Multi TenantFiber optic network expansion in multi-tenant housing is a prime example of the cost efficiency offered by the combined use of the Hexatronic´s Micronet and Ribbonet® technologies.

Ideally, the local access node should be centrally located within a multi-tenant housing block. Each building is then connected to the fiber optic net-work trough these nodes. Since the amount of fiber required between the access node and the building is often substantial, using Micronet is particularly beneficial for this application. By adding a spare micro duct at the time of installation, the amount of fiber may easily be expanded later without any interrup-tions to existing traffic.

When installing fiber in multi-storey buildings, the number of splice points in each property should be minimized in order to cut installation cost. Fiber splicing from each apartment and into the Micronet cables are normally done in a splicing cabinet in the basement or on the ground floor of the building.

Orginating from inside the splicing cabinet, a flame retardant micro duct is installed to each apartment. From each apartment, a pre-connected Ribbonet® fiber eliminates the time consuming mounting of connectors and fiber splicing inside apartments and allows for high-speed installations.

The combined system with Hexatronic Micronet and Ribbonet® technology offers these advantages:

Low installation cost

• Especially when using pre-connected fiber, the time consuming splicing and mounting of connectors is minimized.

• Apartments may be connected on demand.

Flexibility• Network expansion is done easily and quickly by

blowing new fiber into existing micro ducts

• Repair requirements and other network changes are easy to undertake.

8

METRO AND CAMPUS NETWORKS

Metropolitan NetworksThe fiber optic infrastructure that connects major cities to cities within a municipality is almost always built in a redundant ring or mesh structure with a number of nodes connecting fibers to fiber distribution frames for easy access. Networks in densely populated cities can contain fiber rings with hundreds of fibers, while a net-work connecting rural areas only contains few fibers. Despite the network´s design it is often hard to antici-pate future growth and bandwidth need.

Using traditional cabling technologies it is possible to expand network capacity to a certain extent, whereas larger expansions can mean that new cable ducts must be installed, which is very expensive.

Micronet is an ideal system for metropolitan networks. The micro cables’ minimal dimensions mean that it can be installed in very small micro ducts and a large number of micro ducts can be placed in a single, normal cable duct. The Micronet cables can then be installed (i.e. blown) when capacity and end user need so requires, giving large expansion possibilities.

Operational security is an important factor in metro-politan networks. Despite that many preventive measures are taken to enable secure and stable networks, many interruptions are caused by cables being damaged when civil work operations go wrong. In these cases it is important that the network is quickly restored. A Micronet based network can easily be re-established by blowing in new cables and outdoor jointing can in many cases be avoided. Using Hexatronic´s Micronet system in metropolitan networks gives a number of advantages:

Flexibility• Fiber count can be incrementally increased.

Expansion scalability is vast – major fiber increase is possible within existing channels

• Repair is swift and done with minimal interruptions

Low initial investment• Micronet minimizes initial investment cost because

excess fiber capacity is not needed to guarantee future demands

Campus Access – Companies, Hospitals and SchoolsA campus area is a well defined geographical region consisting of several buildings under the same autho-rity. A campus network is constructed in a redundant ring or mesh structure similar to a metropolitan network, although smaller in size. Access nodes are typically placed on the premises and are connected to neigh-boring nodes via optical fibers. Given the high fiber count in a campus network, Hexatronic’s Micronet system is an ideal choice to use when designing and installing campus networks.

Surrounding buildings should in certain cases be con-nected to the area’s campus network. Ribbonet® air blown fiber technology is the perfect solution to use to connect a number of smaller buildings and when initial fiber penetration is low.

In a campus network, each access node should typically contain a fiber distribution frame, usually with fiber optic connections to a joint cabinet in which micro ducts for Micronet or Ribbonet® blown fiber technology is terminated. In order to obtain physical redundancy, each building should be equipped with micro ducts from at least two ways.

Micronet is the most flexible and cost effective campus network system:

Flexibility• Capacity can be incrementally increased as the

campus area grows and new services are introduced. Fiber capacity can also easily be dramatically in-creased.

Low initial investment cost• The systems minimize the initial cost for installation

of optical fibers. The Micronet and the Ribbonet® options give the flexibility of installing fiber on demand, which minimizes initial installation costs.

9

BUSINESS ACCESS

Business Access – Offices and CompaniesThe distribution network in a business area should be designed to fulfill basic requirements such as scalability and redundancy. An access node is normally located on the premises or within the center of a business area. Access nodes are connected to neighboring nodes or to a metropolitan network with either Micronet cables or with Ribbonet® blown fiber installation. Micronet is the most favorable option when connecting access nodes for large business premises and when the number of fi-bers is assumed to be high.

A Ribbonet® installation is the preferred option when connecting several small and medium sized companies, or in business areas with low initial fiber penetration.

Each access node consists of optical distribution frames with optical connectors, normally connected to a splicing cabinet. The cabinet terminates the ducts for the air-blown installation of either the Micronet cable or

Ribbonet® fiber units. To enable physical redundancy, the building should be connected with ducts from at least two different directions.

Hexatronic´s Micronet and Ribbonet® systems are the most flexible and cost effective technologies on the market for construction of any business access network. Both solutions offer:

Flexibility• Bandwidth may be incrementally added as business

grows and new services are introduced.

Low initial investment cost• The systems minimize the initial cost for installation

of optical fibers. The Micronet and the Ribbonet® options give the flexibility of installing fiber on demand, which minimizes initial installation costs.

10

Fiber Identification in Cables according to FIN2012Fibers and secondary coatings (loose tubes) are color coded for easy identification. 12 different colors are used for fibers. For cable designs with more than 12 fibers in each tube the remaining fibers will be marked with an additional ring. The following color sequence is used for fiber colors and tube colors according to FIN2012:

1 - Blue 5 - Grey ´9 - Black2 - White 6 - Orange 10 - Violet3 - Yellow 7 - Brown 11 - Pink4 - Green 8 - Turquoise 12 - Red

Note that uncolored fillers can replace some of the tu-bes.

Duct Identification – Sheath ColorTo easily identify different microduct assemblies in the same trench it is advisable to install duct assemblies with different sheath color. The choice of colors is less important, but normally the following color sequence is used for sheath colors:

1 - Blue2 - White3 - Yellow4 - Green

Duct Identification – Microduct ColorTo identify individual microducts in an assembly, the microducts are provided in 12 different colors. The following color sequence is used for microducts:

1 - Blue 5 - Grey 9 - Black2 - White 6 - Orange 10 - Violet3 - Yellow 7 - Brown 11 - Pink4 - Green 8 - Turquoise 12 - Red

Duct number 1 is located at the center and the ducts are counted counterclockwise or clockwise depending on which end of the duct the projection is shown.

Fiber and Duct Identification

11

Micro cable based on a slim loose tube design with up to 12 tubes per cable. The design facilitates fiber preparation and mid-span access. The cable is suitable for long-distance, air blown installation in microducts, with an inner diameter downto 10 mm. The cable has excellent bend performance and extremely wide operational temperature range suitable for the harsh Nordic climate, down to -45 ºC.

design: Loose tube type: Dielectricdimensions: Ø5.7-7.9mmcapacity: 12-192 fibers

Micro Cables – The Micronet System

Hexatronic Product Number Description No of Fibers ø mm Length m

TOL4019031/12AL GNHLDV Micro Cable 12 12 (1x12) 5,7 2000, 4000, 6000



TOL4019031/96AL GNHLDV Micro Cable 96, 8 96 (8x12) 6,7 2000, 4000, 6000

TOL4019031/192AL GNHLDV Micro Cable 192, 8x24 192 (8x24) 7,9 2000, 4000, 6000

Hexatronic Product Number Description No of Fibers ø mm Length m

TOL4019051/2AL GAHLD Nano Cable 2 2 2,0 2000, 4000, 6000





Nano Cables – The Ribbonet® System

Nano Cables are extremely robust and slim ca-bles in The Ribbonet® system. The cables can be installed in all types of microducts with an inner diameter of 3,5 to 12 mm. The cable is normally installed by blowing up to 1 km or more, but short distances can easily be pus-hed by hand. This enables the nano cable to be blown to fiber optic access cabinets along roads. The connection from the cabinet to the end user can then in many cases be pushed by hand. This procedure enables huge cost savings since a lot of installation steps can be carried out quickly and easy. The cable has excellent bend performance and extremely wide operational temperature range suitable for the harsh Nordic climate, downto -45 ºC.

design: Acrylate coated fiber, G657A (1-8f), Loose tube (12-f)type: Dielectricdimensions: Ø2,0-2,4mmcapacity: 2-12 fibers

CABLES

12

Thick Walled Microducts, Single Tubes, 7/3,5 mm

Thick walled microducts, single tubes for installation of blown fiber or nano cables in the Ribbonet® system. The microducts have a solid, low-friction inner surface coating for best installation performance. The ducts can be installed direct buried (DB) or installed in existing conduits.

type: Direct buried installation or installation in existing conduitsdimensions: Ø7/3,5 mm

Hexatronic Product Number Description Length m

3/MPB30278/1T DB 7/3,5 + DOUBLE SHEATHED 500, 1000, 2000

MPB30284/BU1 DB 7/3,5mm BLUE 500, 1000, 2000

MPB30284/WH1 DB 7/3,5mm WHITE 500, 1000, 2000

MPB30284/YE1 DB 7/3,5mm YELLOW 500, 1000, 2000

MPB30284/GN1 DB 7/3,5mm GREEN 500, 1000, 2000

MPB30284/GY1 DB 7/3,5mm GREY 500, 1000, 2000

MPB30284/OG1 DB 7/3,5mm ORANGE 500, 1000, 2000

MPB30284/BN1 DB 7/3,5mm BROWN 500, 1000, 2000

MPB30284/TQ1 DB 7/3,5mm TURQUOISE 500, 1000, 2000

MPB30284/BK1 DB 7/3,5mm BLACK 500, 1000, 2000

MPB30284/VT1 DB 7/3,5mm VIOLET 500, 1000, 2000

MPB30284/PK1 DB 7/3,5mm PINK 500, 1000, 2000

MPB30284/RD1 DB 7/3,5mm RED 500, 1000, 2000

MICRODUCTS FOR DIRECT BURIED INSTALLATIONS

13

MICRODUCTS FOR DIRECT BURIED INSTALLATIONS


3/MPB30278/7T DB 7x7/3,5mm BLUE 500, 1000, 2000

5/MPB30278/7T DB 7x7/3,5mm WHITE 500, 1000, 2000

4/MPB30278/7T DB 7x7/3,5mm YELLOW 500, 1000, 2000

1/MPB30278/7T DB 7x7/3,5mm GREEN 500, 1000, 2000


3/MPB30278/2T DB 2x7/3,5mm BLUE 500, 1000, 2000

Thick Walled Microduct Assemblies, 7/3,5 mm

Thick walled microduct assemblies for instal-lation of blown fiber or nano cables in the Ribbonet® system. The microducts in the assemblies have a solid, low-friction inner surface coating for best installation perfor-mance. The ducts can be installed direct buried (DB) or installed in existing conduits.

type: Direct buried installation or installation in existing conduitsdimensions, microducts: Ø 7/3,5 mmcapcity: 1, 2, 4, 7, 12 -way

Assemblies with 2 microducts




3/MPB30278/4T DB 4x7/3,5mm BLUE 500, 1000, 2000

5/MPB30278/4T DB 4x7/3,5mm WHITE 500, 1000, 2000


3/MPB30278/12T DB 12x7/3,5mm BLUE 500, 1000, 2000

5/MPB30278/12T DB 12x7/3,5mm WHITE 500, 1000, 2000

4/MPB30278/12T DB 12x7/3,5mm YELLOW 500, 1000, 2000

1/MPB30278/12T DB 12x7/3,5mm GREEN 500, 1000, 2000


14

Thick Walled Microducts, Single Tubes, 14/10 mm

Thick walled microducts, single tubes for installation of Hexatronic Micronet micro ca-bles or nano cables in the Ribbonet® system.The microducts have a solid, low-friction in-ner surface coating for best installation per-formance. The ducts can be installed direct buried (DB) or installed in existing conduits.

type: Direct buried installation or installation in existing conduitsdimensions: Ø14/10 mm


MPB30285/BU1 DB 14/10mm BLUE 500, 1000, 2000

MPB30285/WH1 DB 14/10mm WHITE 500, 1000, 2000

MPB30285/YE1 DB 14/10mm YELLOW 500, 1000, 2000

MPB30285/GN1 DB 14/10mm GREEN 500, 1000, 2000

MPB30285/GY1 DB 14/10mm GREY 500, 1000, 2000

MPB30285/OG1 DB 14/10mm ORANGE 500, 1000, 2000

MPB30285/BN1 DB 14/10mm BROWN 500, 1000, 2000

15

Thick Walled Microduct Assemblies, 14/10 mm

Thick walled microduct assemblies for instal-lation of Hexatronic Micronet micro cables or nano cables in the Ribbonet® system. The microducts in the assemblies have a solid, low-friction inner surface coating for best installation performance. The ducts can be installed direct buried (DB) or installed in existing conduits.

type: Direct buried installation or installation in existing conduitsdimensions, micro ducts: Ø 14/10 mmcapacity: 2, 4, 7-way


3/MPB30277/7T DB 7x14/10mm BLUE 500, 1000

5/MPB30277/7T DB 7x14/10mm WHITE 500, 1000

4/MPB30277/7T DB 7x14/10mm YELLOW 500, 1000


3/MPB30281/2T DB 2x14/10mm BLUE 500, 1000





3/MPB30277/4T DB 4x14/10mm BLUE 500, 1000

5/MPB30277/4T DB 4x14/10mm WHITE 500, 1000

16


MPB30217/005BU1 DB 18/12mm BLUE 1900

MPB30217/005WH1 DB 18/12mm WHITE 1900

MPB30217/005YE1 DB 18/12mm YELLOW 1900

HDPE Ducts, 18/12 mm

HDPE ducts, single ducts and assemblies for installation of micro cables or traditional cables. The microducts in the assemblies have a solid, low-friction inner surface coa-ting for best installation performance. The ducts can be installed direct buried (DB).

type: Direct buried installation or installation in existing conduitsdimensions, microducts: Ø 18/12 mmcapacity: 1, 4-way

Single Tubes


3/MPB302/008T DB 4x18/12mm BLUE 1000

5/MPB302/008T DB 4x18/12mm WHITE 1000

Assemblies

17


3/MPB30213/7T TW 7x5/3,5mm BLUE 500, 1000

5/MPB30213/7T TW 7x5/3,5mm WHITE 500, 1000

4/MPB30213/7T TW 7x5/3,5mm YELLOW 500, 1000

1/MPB30213/7T TW 7x5/3,5mm GREEN 500, 1000


3/MPB30211/2T TW 2x5/3,5mm BLUE 500, 1000

Thin Walled Microduct Assemblies, 5/3,5 mm

Thin walled microduct assemblies for instal-lation of blown fiber or nano cables in the Ribbonet® system. The microducts in the assemblies have a solid, low-friction inner surface coating for best installation perfor-mance. The ducts are intended to be instal-led in existing conduits.

type: Installation in existing conduitsdimensions, microducts: Ø 5/3,5 mmcapacity: 1, 2, 4, 7, 12 -way





3/MPB30212/4T TW 4x5/3,5mm BLUE 500, 1000

5/MPB30212/4T TW 4x5/3,5mm WHITE 500, 1000


3/MPB30214/12T TW 12x5/3,5mm BLUE 500, 1000, 2000

5/MPB30214/12T TW 12x5/3,5mm WHITE 500, 1000, 2000

4/MPB30214/12T TW 12x5/3,5mm YELLOW 500, 1000, 2000

1/MPB30214/12T TW 12x5/3,5mm GREEN 500, 1000, 2000



MPB30220/BU1 TW 5/3,5mm BLUE 500, 1000, 2000

Single microduct

MICRODUCTS FOR INSTALLATION IN EXISTING CONDUITS

18

Thin walled microducts for installation of Hex-atronic Micronet micro cables or nano cables.The microducts have a solid, low-friction inner surface coating for best installation perfor-mance. The ducts are intended to be installed in existing conduits.

type: Installation in existing conduitsdimensions, microducts: Ø 12/10 mm


MPB30262/BU1 TW 12/10mm BLUE 1000, 2100

MPB30262/WH1 TW 12/10mm WHITE 1000, 2100

MPB30262/YE1 TW 12/10mm YELLOW 1000, 2100

MPB30262/GN1 TW 12/10mm GREEN 1000, 2100

MPB30262/GY1 TW 12/10mm GREY 1000, 2100

MPB30262/OG1 TW 12/10mm ORANGE 1000, 2100

MPB30262/BN1 TW 12/10mm BROWN 1000, 2100

MPB30262/TQ1 TW 12/10mm TURQUOISE 1000, 2100

MPB30262/BK1 TW 12/10mm BLACK 1000, 2100

MPB30262/VT1 TW 12/10mm VIOLET 1000, 2100

MPB30262/PK1 TW 12/10mm PINK 1000, 2100

MPB30262/RD1 TW 12/10mm RED 1000, 2100

Thin Walled Microducts, 12/10 mm

19

MICRODUCTS FOR INDOOR INSTALLATION


MPB30203/4 TW 4x5/3,5mm HFFR 500, 1000

MPB30203/7 TW 7x5/3,5mm HFFR 500, 1000

MPB30203/12 TW 12x5/3,5mm HFFR 500, 1000

Thin Walled Microduct Assemblies for Indoor Use, 5/3,5 mm

Thin walled microduct assemblies for instal-lation of blown fiber or nano cables in indoor environments. The microducts are made of halogen free flame retardant material. The microducts have a solid, low-friction inner surface coating for best installation perfor-mance.

type: Indoor installationdimensions, microducts: Ø 5/3,5 mmcapacity: 1, 2, 4, 7, 12 -way

Microduct Assemblies, flame retardant


MPB30202/1 TW Microduct 5/3, 5mm HFFR 500

MPB30201/1 TW Microduct 5/3, 5mm HFFR, double sheated 8mm 500

Single microduct, flame retardant


MPB30273/4 TW 4x12/10mm HFFR 500, 1000

MPB30273/7 TW 7x12/10mm HFFR 500, 1000

Thin Walled Microduct Assemblies for Indoor Use, 12/10 mm

Thin walled microduct assemblies for instal-lation of micro cables in indoor environme-nts. The microducts are made of halogen free flame retardant material. The micro-ducts have a solid, low-friction inner surface coating for best installation performance. type: Indoor installation

dimensions, microducts: Ø 12/10 mmcapacity: 1, 4, 7 -way

Microduct Assemblies, flame retardant


MPB30273/1 TW Microduct 12/10mm HFFR 500

Single microduct, flame retardant

20

The divisible seals for microducts provide a gas and watertight seal for open duct ends installed with nano cables or blown fiber. The seals are designed to be installed after the cable or fiber has been blown in to the microduct.

type: Divisible sealdimensions, microducts: Ø 5/3.5 and 7/3.5 mm

Divisible Seals for Microducts, 12/10, 14/10 and 18/12 mm

These divisible seals for microducts provide a gas and watertight seal for open duct ends installed with Hexatronic micro cables and nano cables. The seals are designed to be installed after the cable or fiber has been blown in to the microduct.

type: Divisible sealdimensions, microducts: Ø 12/10, 14/10and 18/12 mm

Divisible Seals for Microducts, 5/3.5 and 7/3,5 mm

SEALINGS, CONNECTORS AND END STOPS

Hexatronic Product Number Description Pack Qty.

MPB30608/12B 12 mm Divisible Seal, Size 5,0-6,5mm 25

MPB30608/12C 12 mm Divisible Seal, Size 6,5-8,0mm 25

MPB30608/12D 12 mm Divisible Seal, Size 7,0-8,5mm 25

MPB30608/12F 12 mm Divisible Seal, Size 1,5-2,5mm 25

MPB30608/14A 14 mm Divisible Seal, Size 5,8-6,5mm 25

MPB30608/14B 14 mm Divisible Seal, Size 8,0-10,0mm 25

MPB30608/14C 14 mm Divisible Seal, Size 6,5-7,5mm 25

MPB30608/14F 14 mm Divisible Seal, Size 1,5-2,5mm 25

MPB30608/18A 18 mm Divisible Seal, Size 8,0-10 mm 25

MPB30608/18B 18 mm Divisible Seal, Size 7,0-8,0 mm 25

MPB30608/18C 18 mm Divisible Seal, Size 5,0-6,5 mm 25


MPB30608/5A Divisible Seal, Size 1.0-2.0mm 500

MPB30608/5B Divisible Seal, Size 2,1-2,5mm 500

MPB30608/7A Divisible Seal, Size 1.0-2,0mm 500

MPB30608/7B Divisible Seal, Size 2,1-2,5mm 500

21

Microduct snap-in connectors for quick and easy splicing of microducts. The connectors are available for 7/3.5 mm and 14/10 mm ducts and can be direct buried. The con-nectors are equipped with integrated safety locks for accidental opening during installa-tion.

type: Straight Connectordimensions, microducts: Ø 7/3.5, 14/10 mm

Connectors for Thick Walled Ducts


MPB30601/13 CONNECTOR 5/3,5mm 100

MPB30601/15 CONNECTOR 12/10mm 100

MPB30603/6 REDUCER 14/10 -> 12/10 100

MPB30603/5 REDUCER 7/3,5 -> 5/3,5 100

Connectors for Thin Walled Ducts

Microduct snap-in connectors for quick and easy splicing of microducts. The connectors are available for 5/3.5 mm and 12/10 mm ducts and can be direct buried. The con-nectors are equipped with integrated safety locks for accidental opening during instal-lation.

type: Straight Connector or reducersdimensions, microducts: Ø 5/3,5 mm and 12/10mm


MPB30605/7 CONNECTOR 7/3,5mm 100


Cable duct snap-in connectors for quick and easy splicing of microducts. The connector is available for 18/12 mm ducts and can be direct buried.

type: Straight Connectordimensions, microducts: Ø 18/12 mm

Straight Connectors for Cable Ducts, 18 mm



22

End Stops for Thick Walled Microducts

Microduct snap-in end stop connectors for permanent or temporarily sealing of unused microducts to prevent water and dust get-ting into the duct. These end stops can be direct buried. The 7 and 14 mm end stops are equipped with integrated safety locks for unaccidental opening during installation.

type: End stopsdimensions, microducts: Ø 7 mm, 14 mm and 18mm

End Stops for Thin Walled Microducts

Microduct snap-in end stop connectors for permanent or temporarily sealing of unused microducts to prevent water and dust get-ting into the duct.

type: End stopsdimensions, microducts: Ø 5 mm and 12 mm


SXA1139137/13 END STOP 5/3,5mm 100

SXA1139137/15 END STOP 12/10mm 100


MPB30606/7 END STOP 7/3,5mm 100

MPB30606/14 END STOP 14/10mm 100

MPB30606/18 END STOP 18/12mm 100

Gas Block Connector 5 mm

The gas block microduct snap-in connector is normally used between indoor and out-door environments to prevent air flow that may result in condensed water getting into in ducts. After cable installation, the con-nector can be gas sealed by turning a ring on the body.

type: Gas block straight connectordimensions, microducts: 5/3.5 mm

Hexatronic-Product Number Description Pack Qty.

MPB30602 GAS BLOCK CONNECTOR 5/3.5 mm 1.0 - 1.6 mm 100

Gas Block Connector 7-14 mm

The gas block microduct snap-in connector is normally used between indoor and outdoor environments to prevent air flow that may re-sult in condensed water getting into in ducts. After cable installation, the connector can be gas sealed by Pushing the connector ends together. This version is intended for 7 mm thick walled ducts.

type: Gas block straight connectordimensions, microducts: 7/3.5, 10/8, 12/10 and 14/10 mm

Hexatronic-Product Number Description Pack Qty.

MPB30607/7 GAS BLOCK CONNECTOR 7/3.5 mm 1.0 - 1.6 mm 100

MPB30607/12A GAS BLOCK CONNECTOR 12/10 mm 5.5 - 6.6 mm 100

MPB30607/12B GAS BLOCK CONNECTOR 12/10 mm 6.5 - 7.2 mm 100

MPB30607/12C GAS BLOCK CONNECTOR 12/10 mm 7.2 - 8.2 mm 100

MPB30607/14A GAS BLOCK CONNECTOR 14/10 mm 6.5 - 7.2 mm 100

MPB30607/14B GAS BLOCK CONNECTOR 14/10 mm 7.6 - 8.2 mm 100

23

Ribbonet® and Hexatronic Micronet TrainingTogether with certified training companies, Hexatronic offers various training classes for the Ribbonet® and Hexatronic Micronet systems. The training is normally located at training centers in Finland and is scheduled. Certain training is held on request. The following training courses are offered:

Ribbonet® and Hexatronic Micronet Basic Installation Training2 day training course held at training facilities in Finland. This course gives an overview of how to install the Ribbonet® and Hexatronic Micronet systems. Focus is on practical installation in the field.

Ribbonet® Certified Installer TrainingThis 4 day course is a comprehensive overview of the Ribbonet® system. The successful student will be certi-fied as an approved Ribbonet® installer. The course is held on request.

Hexatronic Micronet Certified Installer TrainingThis 4 day course is a comprehensive overview of the Hexatronic Micronet system. The successful student will be certified as an approved Micronet installer. The course is held on request.

Network PlanningThis 2 day course fouses on network planning for the Ribbonet® and Hexatronic Micronet systems. The course is held on request.

TRAINING

linkedin.hexatronicpartners.se twitter.hexatronicpartners.se youtube.hexatronicpartners.se issuu.hexatronicpartners.se facebook.com/hexatronic

HCI 28701-0008-A© Hexatronic C&I AB 2016

Hexatronic Cables & Interconnect Systems AB, Kabelvägen 1, SE-824 82 HudiksvallTel +46 (0)10 453 02 00 [email protected] www.hexatronic.com

Industry Leading System Solutions for Fiber Optic Communications

Hexatronic Cables & Interconnect Systems develops, manufactures, markets and provides solutions within the fiber optic cable infra-structure, for telecom companies. Hexatronic Cables & Interconnect Systems manufacture fiber optic cable, duct, copper cable and net-work accessories. The company originates from the former Ericsson site in Hudiksvall. Our products are developed and manufactured by Swedish specialists, with many years of experience and unique expertise in fiber optics. The product portfolio includes the industry leading brands Ribbonet® and Micronet.

A part of Hexatronic GroupHexatronic Cables & Interconnect Systems is a part of Hexatronic which is an innovative Swedish technology group, specializing in fiber communications. The Group provides products and solutions for the fiber optic network and together, the five independent, entrepreneurial companies offer a full range of passive infrastructure. We combine our large corporate stability and resources with small company flexibility and speed.

Our customers are companies within the telecommunications industry such as communications and telecom suppliers, operators and net-work owners. The companies within The Group are Hexatronic Cables & Interconnect in Hudiksvall, Memoteknik in Skellefteå, Hexatronic Elektronik & Data in Gothenburg, The Blue Shift and Proximion in Stockholm, TD Fiberoptik in Örebro.

For more information about Hexatronic Group: www.hexatronicgroup.com


Documents

Fiber Optic Products for Access Networkshexatronic.com/media/202200/fiber-optic-products-for...Fiber Optic Products for Access Networks Baltic Edition 2 HCI 28701-0008-A Passive fiber