Embed Size (px)
Citation preview
Dr. Daniyan Ilesanmi Afolabi
I am Daniyan Ilesanmi Afolabi, a Postdoctoral Research Fellow in the Department of Industrial Engineering. Teaching and Research Fields
Production Engineering, Advanced and Additive Manufacturing, Reconfigurable Manufacturing Systems, Automation and Robotics as well as Renewable Energy Production Engineering:
It deals with development (design, fabrication and performance evaluation) of cost effective systems and products using the combination of various manufacturing techniques and appropriate technologies that satisfies the users’ demand in the most smoothest and judicious way. Advanced and Additive Manufacturing
This deals with reconfiguration of machines and systems. It also involve the use of innovative technology to improve products or processes. Simulation and various modelling tools are often employed to optimize production processes with a focus on increasing productivity. Research in this area also involves advances in Industry 4.0 in line with the broader 4th Industrial Revolution. Automation and Robotics
This deals with the development of smarts systems for effective delivery, monitoring and control. Since manufacturing industries are profit oriented and are concerned with the precision and productivity per worker of their plants, automatic systems offers the solution of high productivity and effective control without sacrificing precision and accuracy. This include; the Artificial Neural Network (ANN), The Distributed Control System (DCS); Supervisory Control and Data Acquisition (SCADA), Instrumentation, Robotics and Artificial Intelligence (AI) Renewable Energy
This is in line with the global quest for increased energy security as well as the mandate of Clean Air Act of the US Environmental Protection Agency and United Nations International Conferences on Climate change. Research in this area is geared towards development of safe and sustainable energy system in order to the energy crisis which is assuming a global dimension.
CURRICULUM VITAE Name in full (surname in capital letters): Dr. DANIYAN, Ilesanmi Afolabi
(B.Tech.; M.Eng.; Ph.D; COREN)
Place and Date of Birth: Ikare Akoko, Ondo State; 9th December, 1983
Marital Status: Married
Numbers and Ages of Children: Nil
Nationality at Birth: Nigerian
Present Nationality: Nigerian
Permanent Address: Zethushof Flat 711, 620 Park Street, Arcadia 0083, Pretoria,
South Africa.
Phone: +27815164149
e-mail: [email protected]; [email protected]
Contact Address: Department of Industrial Engineering, Tshwane University
of Technology, Staastartillerie Road, Private
Bag X680, Pretoria 0001, South Africa
Name and Address of Next of Kin: Mrs Oluwatoyin Esther Daniyan (Spouse): +27727021931
Department of Accounting, Tshwane University of Technology,
Pretoria, South Africa
ORCID Identifier: 0000-0002-7238-9823
Educational Institutions Attended with Dates:
Federal University of Technology Akure, Ondo State, Nigeria (2013-2017)
Federal University of Technology Akure, Ondo State, Nigeria (2010-2012)
Ladoke Akintola University of Technology Ogbomoso, Oyo State, Nigeria (2002-2007)
Unity Secondary School, Owo, Ondo State, Nigeria (1994-2000)
Aunty Bisi Nursery & Primary School, Ugbe Akoko, Ondo State, Nigeria (1987-1994)
Academic Qualifications obtained with Dates and Class of Degrees:
Doctor of Philosophy
Ph.D Mechanical Engineering; Production Engineering & Renewable Energy Option: (2017)
Master of Engineering
M. Eng. Mechanical Engineering; Production Engineering Option: (Ranked first) (2012)
Bachelor of Technology
B. Tech. Chemical Engineering: Second Class Lower Division: (2008)
West African Senior School Certificate: (2001)
Foreign Qualification Evaluation
MIE (2018)
South African Qualification Authority (SAQA) (2018)
Professional Qualification:
Professional Engineer & Member, Council for the Regulation of Engineering in Nigeria (COREN:
R. 25,184) (2013)
Associate Member, Southern Africa Institute of Industrial Engineering, 5001 (2019)
Area of Specialization
Mechanical Engineering; (Production Engineering, Advanced and Additive Manufacturing,
Automation and Robotics, Renewable Energy
Previous Employment with year
Bofoat Model College, Ikare Akoko, Ondo State, Nigeria. (2009)
Ikare City Polytechnic, Ikare Akoko, Ondo State, Nigeria. (2011-2012)
Afe Babalola university, Ado Ekiti, Nigeria (2012-2018)
Senior Lecturer, (Level 05, Step 2). Department of Mechanical & Mechatronics
Engineering, Afe Babalola University Ado Ekiti, Nigeria. (2012-2018)
Lecturer I, (Level 04, Step 9). Department of Mechanical & Mechatronics
Engineering, Afe Babalola University Ado Ekiti, Nigeria. (2015-2017)
Lecturer II, Department of Mechanical & Mechatronics Engineering, Afe
Babalola University Ado Ekiti, Nigeria. (2012-2015)
Present Appointment:
Postdoctoral Fellow. Department of Industrial Engineering, Tshwane University of
Technology, Pretoria, South Africa (2018-till date)
Responsibilities and Job Description
1. Preparing lectures, teaching and grading of departmental specific and general college courses
at undergraduate and post graduate level
2. Curriculum development and review for both the undergraduate and post graduate levels
3. Conducting of tutorials, seminars of tutorials and assignments
4. Supervision of undergraduate and post graduate projects in the department
5. Coordination of undergraduate course practical’s with help of laboratory technologist and
technicians
6. Coordination and participation in curriculum development, departmental academic,
administrative and research activities
7. Member, students’ advisory committee
8. Serving as member of various project committee within and outside the school
9. Member, Energy and Production Technologies Research Group.
10. Carrying out research on the reconfiguration of jigs and fixtures for welding operations during
rail car manufacturing.
11. Development of indigenous technology for revamping the railcar sector in South Africa.
Administrative Experience
Academic Officer, Department of Mechanical & Mechatronics Engineering, Afe Babalola
University, Ado Ekiti, Nigeria (2013-2018)
Editorial Member, International Journal of Science and Research (IJSR) (2013-till date)
Editorial Member, AR Research Publication and Conference World (2013-till date)
Reviewer Panel Member, International Journal of Scientific Engineering and Research (2013-
till date)
Commendations and Honours:
Runner-Up: Best SAIIE Industrial Engineering Practitioner (Employer’s choice) (2019)
Best Lecturer, Department of Mechanical & Mechatronics Engineering (2017, 2016 & 2015)
Best Graduating Student: 2011 M. Eng. Mechanical Engineering Class
(Ranked first with CGPA of 4.83)
Certificate of Commendation, National Youth Service Corps (NYSC); 2009.
Professional Accomplishments:
Member, Council for the Regulation of Engineering in Nigeria (COREN) R. 25,184 (2013)
Associate Member, Southern Africa Institute of Industrial Engineering, (SAIIE) 5001 (2019)
Professional Engineer, Engineering Council of South Africa (In view)
Research Grants with dates: Gibela Postdoctoral Fellowship Grant (2018)
Gibela Postdoctoral Fellowship Grant (2018-2020)
2018-2019 (R220,000) per anum (Principal Investigator) 2019-2020 (R220,000) per anum (Principal Investigator) Total sum received (R440,000)
Teaching and Research Experience:
Tshwane University of Technology, Pretoria, South Africa (2018-till date)
External Examiner, School of Mechanical, Industrial and Aeronautical Engineering University
of the Witwatersrand, Johannesburg (2019-till date)
Afe Babalola University, Ado Ekiti, Nigeria (2012-2018)
Ikare City Polytechnic, Ikare Akoko, Ondo State: (2011)
Bofoat Model College, Ikare Akoko, Ondo State : (2009)
Comprehensive College, Ijer, Buruku, Benue State: (2008)
Industrial Experience
Jof Industry Nigeria Limited, Owo, Ondo State, Nigeria: SWEP Trainee (May-July, 2004)
Jof Industry Nigeria Limited, Owo, Ondo State, Nigeria: SWEP Trainee (May-July, 2005)
Falcons Chemicals, Limited, Ikeja, Lagos, Nigeria: SIWES Trainee (March-Sept. 2006)
Tshwane University of Technology, Pretoria, South Africa: Postdoctoral Research Fellow
(March 2018-till date)
Courses taught at Undergraduate Level
[1] MEE 322: Fluid Mechanics II (3 Units)
[2] ENG 214: Basic Fluid Mechanics (3 Unit)
[3] MCT 308: Electromechanical Machines (3 Units)
[4] MEE 526: Maintenance Management (2 Units)
[5] ENG 235: Engineering Thermodynamics (2 Units)
[6] MEE 411 Mechanical Vibrations (2 Units)
[7] MEE 313: Strength of Materials II (3 Units)
[8] MEE 413: Production Engineering I (2 units)
[9] MEE 521: Turbo Machinery (3 Units)
[10] MEE 571 & MEE 572: Assigned Project (6 Units)
Courses taught at Post Graduate Level
[1] MEE 721: Advanced Turbo Machinery (3 Units)
[2] MEE 805: Systems Engineering (3 Units)
[3] MME 823: Control Systems Engineering (3 Units)
[4] MEE 826: Maintenance Management (3 Units)
[5] MEE 802: Computational Fluid Dynamics (3 Units)
Major Research, Project and Inventions (30)
1. Development of an Autonomous Ground Vehicle for Environmental Characterization
(Ongoing)
2. Development of Reconfigurable Jigs and Fixture for Welding Operations during Rail Car
Manufacturing (Ongoing)
3. Development of a Wind Turbine for Electricity Generation (Ongoing)
4. Development of a Smart Biogas Plant for Energy Generation from Animal Waste (2018)
5. Development of an Automated Irrigation System (2018)
6. Development of a Humidifier Cooler for Room Ventilation (2018)
7. Development and Optimization of Wood Gasifier for Energy Generation (2018)
8. Development and Simulation of a Reconfigurable Fixture Assembly Using Pneumatic Control
(2018)
9. Development of a Remote Controlled Alert System for Human Access into Premises (2018)
10. Development of Energy Efficient Multi-Crop Tray Dryer (2018)
11. Development of a Multi Feedstock Biodiesel Plant. Ph. D Research work, Completed at The
Federal University of Technology, Akure, Ondo State, Nigeria. (2017)
12. Development and Optimization of a Smart Biogas Plant for Energy Generation from Food
Waste (2017)
13. Development and Optimization of a Small Scale Biodiesel Processor (2017)
14. Emission Characteristics of Diesel and Biodiesel Blends (2017)
15. Development of a Smart Diabetes Monitoring Device (2017)
16. Development of a Mixer for Concrete Production (2016)
17. Development of a Prototype Test Rig for Oil Leakages Detection in Pipelines (2016)
18. Development of a Remote Controlled Alert System for Automobile Access into Premises
(2016)
19. Development of a Multi-Feed Pelletizer for the Production of Organic Fertilizer (2016)
20. Development of Machinery for the Production of Organic Fertilizers (2016)
21. Development of a Belt Conveyor for Small Scale Industries (2016)
22. Development of a Plastic Recycling Machine (2016)
23. Development of a Cassava Peeling Machine (2015)
24. Optimal Design of Micro Hydro Turbine (Archimedes Screw Turbine) in Arinta Water Fall in
Ekiti State, Nigeria (2015)
25. Development of Indigenous Engineering and Technology in Nigeria for Sustainable
Development through Promotion of SMES (Case of Design of Manually Operated Paper
Recycling Plant). (2015)
26. Distillation Characteristics of Rubber Seed Oil, Biodiesel and Blend with Diesel (2014)
27. Photovoltaic Modules Performance Loss Evaluation for Nsukka South East Nigeria and
Mitigable Designs. (2014)
28. Production of 30,000 tons of Caustic Potash Per Anum from Cocoa Pod Husk (2013)
29. Correlation of Vapour-Liquid Equilibrium Data Using Neural Network for Hydrocarbon ternary
system. (2013)
30. Development of a Processor for Producing Biodiesel from used and unused vegetable oil.
M.Eng. Research work, Completed at The Federal University of Technology, Akure, Ondo State,
Nigeria. (2012)
Publications
Articles [104]
[1] Daniyan, I. A., A. O. Adeodu, O. M. Dada, and A. A. Aribidara (2013): Design of a Small Scale
Biodiesel Processor.
Published in Journal of Emerging Trends in Engineering and Applied Sciences (JETEAS)
4(4)576-580.
[2] Daniyan, I. A., A. O. Adeodu, O. O. Omitola, O. L. Daniyan, and A. S. Yusuff (2013).
Use of Artificial Neural Network for Correlation of Vapour-Liquid Equilibrium Data for
Hydrocarbon ternary system. (Ethane-n-Butane-Pentane). (Published in the International
Journal of Scientific and Engineering Research. Volume 4, Issue 8). pp. 1980-1898.
[3] Bello, E. I., I. A. Daniyan, A. O. Akinola, and T. I. Ogedengbe (2013): Development of a Biodiesel
Processor.
Published in Research Journal of Engineering and Applied Sciences (RJEAS) 2(3)182-186.
[4] Yusuff, A. S., L. T. Popoola, O. O. Omitola, A. O. Adeodu and I. A. Daniyan (2013): Mathematical
Modeling of Fixed Bed Adsorption Column for Liquid Plate Solute: Effect of Operating
Variables. (Published in the International Journal of Scientific and Engineering Research,
IJSER Vol. 4, Issue 8). pp. 811-822.
[5] Adeodu, A. O., I. A. Daniyan and A. S. Yusuff (2013): Assessment of Soil, Water and Plant
Pollution by Heavy Metals from Petroleum and Petrochemical Companies in Nigeria. (A Case
Study of Eleme Petrochemicals, Warri Refinery, Atlas cove depot, Mosimi depot, Ilorin depot,
Ibadan depot, Ejigbo depot, Ore depot). (Published in the International Journal of Scientific
and Engineering Research. Volume 4, Issue 7. pp. 2401-2412
[6] Anyaeche, C.O., A. O. Adeodu and I. A. Daniyan (2013): Anthropometry as an Ergonomic
Design Factor in an Open Plan Selected Computer Operator Work Station: Cyber Cafés
Perspectives. (Published in the International Journal of Scientific and Engineering Research.
Volume 4, Issue 7). pp. 2379-2390.
[7] Anyaeche, C. O., A. O. Adeodu and I. A. Daniyan (2013): Acoustic as an Ergonomic Design
Factor in an Open Plan Selected Computer Operator Work Station: Cyber Cafés Perspectives.
(Published in the International Journal of Scientific and Engineering Research. Volume 4,
Issue 8). pp. 1904-1913.
[8] Daniyan, I. A., A. O. Adeodu and O. O. Adaramola (2013). Correlation of Vapour-Liquid
Equilibrium Data Using Neural Network for Hydrocarbon Ternary Sytem. (Ethane-n-Pentane-
n-Hexane). Journal of Emerging Trends in Engineering and Applied Sciences, JETEAS 4(6) 763-
768.
[9] Oguntuase, O. B., I. A. Daniyan and A. O. Adeodu (2013). Design and Fabrication of Burglary
and Assembly of Aluminium Window Frame. (Students’ Work Experience Programme SWEP,
Afe Babalola University, Ado Ekiti, Nigeria). International Journal of Innovative Research in
Science and Engineering Technology. IJIRSET 2(12) 7930-7940.
[10] Daniyan, I. A., A. O. Adeodu and O. M. Dada (2014). Design of Material Handling Equipment:
Belt Conveyor System for Crushed Limestone Using 3 Roll Idlers. Journal of Advancement in
Engineering and Technology. 1(1) 1-7.
[11] Adeodu, A. O., I. A. Daniyan and O. M. Dada (2014). An Assessment of Physical Strain
Experienced by Manual Workers in Bricklaying Operation: A Case Study in Nigeria. Journal of
Computation in Biosciences and Engineering. 1(1) 1-6.
[12] Daniyan, I. A., A. O. Adeodu and O. L. Daniyan (2014). Prediction of Vapour-Liquid Equilibrium
Data Using Neural Network for Hydrocarbon Ternary System (Ethane-Pentane-n-Butane).
Journal of Computation in Biosciences and Engineering 1(1) 1-7.
[13] Daniyan, I. A., O. L. Daniyan, A. O. Adeodu and A. A. Aribidara (2014). Towards Sustainable
Development in the Third World: Design of a Large Scale Biodiesel Plant. Journal of
Bioprocessing and Chemical Engineering. 1(1)1-9.
[14] Adeodu, A. O., I. A. Daniyan and O. O. Adaramola (2014). Anthropometry Evaluation Using
Analytical Hierarchical Process and Independent Test Method for Hospital Bed Design: A Case
Study in Nigeria. Journal of Computation in Biosciences and Engineering 1(1) 1-7.
[15] Bello, E. I., I. A. Daniyan and F. Otu (2014). Distillation Characteristics of Rubber Seed Oil,
Biodiesel and Blend with Diesel. Research Journal in Engineering and Applied Sciences 3(2)
114-117.
[16] Daniyan, I. A., A. O. Adeodu and D. F. Adewumi (2014). Design of a Processor for the
Production of 30,000 Tons of Caustic Potash Per Anum from Cocoa Pod Husk. Int’l Journal of
Science and Research (IJSR) 3(3):691-700
[17] Adewumi, D. F., Daniyan, I. A. and A. O. Adeodu (2014). Determination of Heavy Metals in
Water, Fish and Soil Samples from Antau River in Keffi, Nasarawa State, Nigeria: A Case Study
of Antau River in Keffi, Nasarawa North Central Nigeria. Int’l Journal of Science and Research
(IJSR) 3(3):701-705.
[18] Adewumi, D. F., Daniyan, I. A. and A. O. Adeodu (2014). Physico-Chemical Properties of Ala
River, Akure, Ondo State, Nigeria. (A Case Study of Ala River in Akure, South Western Nigeria).
Journal of Physical and Chemical Sciences 1(2):1-6.
[19] Adeodu A. O., Daniyan I. A., Adaramola O. O., (2014). Anthropometry as Ergonomic
Consideration for a Hospital Bed design in Nigeria. International Journal of Scientific and
Engineering Research. Vol. 5, Issue 5 pp. 485-492.
[20] Olateju I. I., Adeodu A. O., and Daniyan I. A., (2014). Assessment of Adsorption Kinetics in a
Quaternary Liquid phase System using Activated Carbon derived from Oil palm empty fruit
bunch. Journal of Bioprocessing and Chemical Engineering. 1(3)1-6.
[21] Olateju I. I., Adeodu A. O., and Daniyan I. A., (2014). Isotherms study of equilibrium adsorption
of a Quaternary system unto activated Carbon derived from Oil palm empty fruit bunch.
Journal of Bioprocessing and Chemical Engineering. Vol. 1, Issue 3, pp.1-6.
[22] Daniyan, O. L and I. A. Daniyan (2014). Towards Sustainable Solar Power System in Nigeria:
The Planning and Budgeting Considerations. International Journal of Scientific and
Engineering Research. Vol. 5, Issue 7. pp. 348-352.
[23] Daniyan, O. L., I. A. Daniyan, B. I. Okere, N. Aliyu and E. E Ezema (2014). Photovoltaic Modules
Performance Loss Evaluation for Nsukka South East Nigeria and Mitigable Designs. Journal of
Engineering Research and Applications. Vol. 4, Issue 8, pp. 90-92.
[24] Daniyan, I. A., A. O. Adeodu and O. M. Oladunjoye (2015). Effects of Catalyst Variation on
Biodiesel Yield. Journal of Advancement in Engineering and Technology. Vol., 3 Issue 1, pp.
1-3.
[25] Akinnuli, B. O., I. A. Daniyan, A. O. Adeodu and I. E. Elemure (2015). Development of a Model
for Lathe Machine’s Installation, Completion Time and Due Dates Prediction. Int’l Journal of
Innovative Research in Science, Engineering and Technology. Vol., 4, Issue 5, pp.3768-3776.
[26] Akinnuli, B. O., I. A. Daniyan, A. O. Adeodu and I. E. Elemure (2015). Procedural Steps for
Effective Delivery, Installation and Commissioning of Drilling Machine. Journal of
Advancement in Engineering and Technology. Vol., 2 Issue 4, pp. 1-5.
[27] Adeodu, A. O., I. A. Daniyan, T. M. Azeez and C. U. Omohimoria (2015). Effect of Microwave
Curing on the Tensile Property of Particulate Reinforced Polymer Matrix Composites. Journal
of Advances in Materials. Vol., 4, Issue 3 pp. 67-74.
[28] Dada, O. M., I. A. Daniyan and O. O. Adaramola (2015). Optimal Design of Micro Hydro Turbine
(Archimedes Screw Turbine) in Arinta Water Fall in Ekiti State, Nigeria. Research Journal in
Engineering and Applied Sciences, Vol., 4, Issue 2 pp. 34-38.
[29] Daniyan, I. A., A. O. Adeodu, O. M. Dada and D. F. Adewumi (2015). Effects of Reaction Time
on Biodiesel Yield. Journal of Bioprocessing and Chemical Engineering. Vol., 3, Issue 2, pp. 1-
3.
[30] Adeodu, A. O., I. A. Daniyan, C. U. Omohimoria and S. O. Afolabi (2015). Development of
Indigenous Engineering and Technology in Nigeria for Sustainable Development through
Promotion of SMES (Case of Design of Manually Operated Paper Recycling Plant). Int’l Journal
of Science, Technology and Society Vol., 3, Issue 4 pp. 124-131.
[31] Adewumi, D. F., I. A. Daniyan, K. A. Adigun and A. O. Adeodu (2015). Determination Trace
Metals in Fish, Water, and Sediments of Some Ponds in Ado, Ikere and Iyin Ekiti, Ekiti State,
Nigeria. Journal of Physical and Chemical Sciences. Vol., 3, Issue 2, pp. 1-4.
[32] Oladapo, B. I., Balogun, V. A., Adeoye, A. O. M., Ijagbemi, C. O., Afolabi, S. O., Daniyan, I. A.,
Esoso, A. A. and Asanta, S. P. (2016). Model Design and Simulation of Automatic Sorting
Machine Using Proximity Sensor. Engineering Science and Technology, an International
Journal. 19(3):1452-1456. Scopus Indexed.
[33] Bello, E. I., Ogedengbe, T. I., Lajide, L. and I. A. Daniyan (2016). Optimization of Process
Parameters for Biodiesel Production Using Response Surface Methodology. American Journal
of Energy Engineering. 4(2):8-16.
[34] Daniyan, I. A., Adeodu, A. O., Azeez, T. M., Dada, O. M. and Olafare, A. O. (2016). Optimization
of Peeling Time and Operational Speed for Cassava Peeling Using Central Composite Design
and Response Surface Methodology. International Journal of Engineering Sciences and
Research Technology. 5(9):630-639.
[35] Dada, O. M. Daniyan, I. A., Azeez, T. M. and Adaramola, O. O. (2016). Audit of Electricity
Generation in University of Lagos, Nigeria. International Journal of Energy and Power
Engineering. 5(2):29-33.
[36] Oladapo, B. I., Balogun, V. A., Oyegoke, S. O. Adeoye, A. O. M., Ijagbemi, C. O., Afolabi, S. O.,
Daniyan, I. A., Akinola, S. O. Asanta, S. P. and I. D. Uchegbu (2016). Experimental Analytical
Design of CNC Machine Tool SCFC based on Electro-pneumatic System. Engineering Science
and Technology, an International Journal. 19(4)1958-1965. Available at
http://dx.doi.org/10.1016/j.jestch.2016.08.010. Scopus Indexed.
[37] Oladapo, B. I., Balogun, V. A., Adeoye, A. O. M., Ijagbemi, C. O., Afolabi, S. O., Daniyan, I. A.,
and Asanta, S. P. (2016). Model Design and Simulation of Automatic Sorting Machine Using
Proximity Sensor. Engineering Science and Technology, an International Journal.
19(2016):1452-1456. Scopus Indexed.
[38] Daniyan, I. A., Bello, E. I., Ogedengbe, T. I., Lajide, L. and Mogaji, P. B. (2017). Development of
a Model for Predicting the Yield of Biodiesel during Biodiesel Production. FUTA Journal of
Engineering and Engineering Technology. 11(1):68-72.
[39] Daniyan, I. A. and Akhere, O. M. (2017). Development of a Multi-Feed Pelletizer for the
Production of Organic Fertilizer. American Journal of Mechanical and Materials Engineering.
1(3):44-48.
[40] Daniyan, I. A., Aderoba A. A., Jimmy, D. N., Rominiyi, O. L. and Adewumi, D. F. (2017).
Development of a Mixer for Concrete Production. Applied Engineering; 1(4)90-94.
[41] Daniyan, I. A., Omokhuale, A. M., Aderoba, A. A. and Ikumapayi, O. M. (2017). Development
and Performance Evaluation of Organic Fertilizer Machinery. Journal of Cogent Engineering.
DOI: http://doi.org/10.1080/23311916.2017.1364044. Scopus Indexed.
[42] Daniyan, I. A., Daniyan, O. L., Mayungbe, O. E. and Oguntuase, O. B. (2017). Development of
a Belt Conveyor for Small Scale Industry. Journal of Advancement in Engineering and
Technology, 5(3)1-5.
[43] Daniyan, I. A., Adeodu, A. O. and Adewumi, D. F. (2017). A Review of Strategic Management
of Water Resources. Journal of Physical and Chemical Sciences 5(4)1-6.
[44] Daniyan, I. A., Adeodu, A. O., Onibokun, W. O. and Adewumi, D. F. (2017). Development of a
Plastic Recycling Machine. Journal of Advancement in Engineering and Technology, 5(3)1-5.
[45] Adeodu, A. O., Daniyan, I. A., Babalola, S. A., Okojie, F. and Aderoba, A. A. (2017).
Development of a 30 kg Aluminium Oil-Fired Crucible Furnace Using Locally Sourced Materials.
American Journal of Mechanics and Applications, 5(3)15-21. doi:
10.11648/j.ajma.20170503.11
[46] Daniyan, I. A., Adeodu, A. O., Kayode, J. F., Asibe, J. and Aderoba, A. A. (2017). Development
of a Remote Controlled Alert System for Automobile Access into Premises. Journal of
Automation, Control and Intelligent Systems 5(5)61-66.
[47] Daniyan, O. L., Daniyan, I. A. and Ale, F. (2017). A New Optimized Radio Telescope Receiver
Architecture. Journal of Advancement in Engineering and Technology, 5(4)1-5.
[48] Igelegbai, E. E., Alo, O. A., Adeodu, A. O. and Daniyan, I. A. (2017). Evaluation of
Mechanical and Microstructural Properties of α-Brass Alloy Produced from Scrap Copper and
Zinc Metal through Sand Casting Process. Journal of Minerals and Materials Characterization and
Engineering, 5:18-28.
[49] Daniyan, I. A. (2018). Comparative Analysis of Production of Biodiesel from Used Oil via Heterogeneous Transesterification. International Journal of Academic and Applied Research (IJAAR) ISSN: 2000-005X 2(4), pp. 1-5. http://www.ijeais.org/ijaar
[50] Daniyan, I. A. and Umakhihe, A. (2018). Development of a Deionizer for Water Purification. International Journal of Academic Engineering Research (IJAER) ISSN: 2000-001X. 2 (4), pp. 1-8. www.ijeais.org/ijaer
[51] Daniyan, I. A. and Cookey-Gam, R. S. (2018). Development of a Paint Mixing Machine. International Journal of Academic Engineering Research (IJAER) ISSN: 2000-001X. 2(4) pp. 9-
16. [52] Adeodu, A. O. and Daniyan, I. A. (2018). Development and Optimisation of Drying Parameters
for Low-Cost Hybrid Solar Dryer Using Response Surface Method. Journal of Sustainable Bioenergy Systems, (8): 23-35.
[53] Daniyan, I. A., Aderoba, A. A. Atamunotoru, D. A. and Rominiyi, O. L. (2018). Development and Performance of a Livestock Feed Mixer. MOJ App Bio Biomech.; 2(4):242‒245.
[54] Daniyan, I. A., Ahwin, A. K., Aderoba, A. A. and O. L. Daniyan (2018). Development of a Smart Digester for the Production of Biogas. Petroleum and Coal, 60(5):804-821. Scopus Indexed.
[55] Daniyan, I. A., Daniyan, O. L., Adeodu, A. O., Ojaokomo, F. and Mpofu, K. (2018). Development of Controlled Alert System for Human Access into Premises. Journal of Emerging Trends in Engineering and Applied Sciences (JETEAS) 9(3): 140-149.
[56] Daniyan, I. A., Dada, O. M., Adeodu, A. O., Uchegbu, I .D., Isijola, O. O. and Mpoku, K. (2018). Development and Performance Evaluation of a Humidifier for Room Ventilation. Journal of Emerging Trends in Engineering and Applied Sciences (JETEAS) 9(3): 123- 128.
[57] Daniyan, I. A., Mpofu, K. and Osadare, D. F. (2018). Design and simulation of a controller for an active suspension system of a rail car. Cogent Engineering, 5: 1545409, pp. 1-15. DOI:
http://dx.doi.org/10.1080/23311916.2018.1545409. Scopus Indexed. [58] Daniyan, I. A., Daniyan, O. L., Adeodu, A. O., Azeez, T. M. and Ibekwe, K. S. (2018). Design and
Simulation of a Wind Turbine for Electricity Generation. International Journal of Applied Engineering Research, 13 (23):16409-164717. Scopus Indexed.
[59] Daniyan, I. A., Daniyan, O. L., Adeodu, A. O., Uchegbu, I. D. and Abiona, O. H. (2018). Development and Optimization of a Smart System for Biogas Production using Animal Waste. International Journal of Applied Engineering Research, 13 (23):16394-16408. Scopus Indexed.
[60] Daniyan, I. A., Ahwin, K. A., Aderoba, A. A., Daniyan, O. L. and Mpofu, K. (2018). Development and Optimization of a Smart Digester for the Production of Biogas. Proceedings of the International Conference on Industrial Engineering and Operations Management Pretoria / Johannesburg, South Arica, October 29 – November 1, 2018. pp. 1456-1459. Scopus Indexed.
[61] Daniyan, I. A., Mpofu, K., Daniyan, O. L., and Adeodu, A. O. (2018). Design and Simulation of a PID Controlled Active Suspension System of a Rail Car. Proceedings of the International Conference on Industrial Engineering and Operations Management Pretoria / Johannesburg, South Arica, October 29 – November 1, 2018. pp. 1470-1480. Scopus Indexed.
[62] Daniyan, I. A., Mpofu, K. and Adeodu, A. O. (2019). Optimization of Welding Parameters using Taguchi and Response Surface Methodology for Rail Car Bracket Assembly. The International Journal of Advanced Manufacturing Technology.100:2221-2228. https://doi.org/10.1007/s00170-
018-2878-9. Scopus Indexed.
[63] Daniyan, I. A., Mpofu, K. and Adeodu, A. O. (2019). Investigating the effect of carbon steel STKM 13a thermal and electrical properties during welding assembly of the lower brackets of a rail car. Int. Journal of Advanced Manufacturing Technology, 102:43–53. Scopus Indexed.
[64] Daniyan, I. A., Adeodu, A. O., Oladapo, B. I., Daniyan, O. L. and Ajetomobi, O. R. (2019).
Development of a reconfigurable fixture for low weight machining operations. Cogent Engineering, 6: 1579455, pp. 1-17. https://doi.org/10.1080/23311916.2019.1579455. Scopus Indexed.
[65] Tlhabadira, I., Daniyan, I. A., Machaka, R. , Machio, C ., Masu, L. and VanStaden L. R. (2019). Modelling and Optimization of Surface Roughness during AISI P20 Milling Process using Taguchi Method. Int. Journal of Advanced Manufacturing Technology, 102(9-12):3707-3718. https://doi: 10.1007/s00170-019-03452-4. Scopus Indexed.
[66] Daniyan, I. A., Mpofu, K., Daniyan, O. L. and Adeodu, A. O. (2019). Dynamic Modelling and Simulation of Rail car Suspension Systems using Classic Controls. Cogent Engineering. 6:1602927. http://doi:10.108/23311916.2019.1602927. Scopus Indexed.
[67] Daniyan, I. A., Bello, E.I., Ogedengbe, T. I. and Mogaji, P. B. (2019). Gas Chromatography and Fourier Transform Infrared Analysis of Biodiesel from Used and Unused Palm Olein Oil. International Journal of Engineering Research in Africa, 42:47-64. http://doi:10.4028/www.scientific.net/JERA.42.47. Scopus Indexed.
[68] Daniyan, I.A., Dahunsi, O. A, Oguntuase, O. B., Daniyan O. L., and Mpofu, K. (2019). Development of a Prototype Test Rig for Leak Detection in Pipelines. Procedia CIRP, 80:524-529. Scopus Indexed.
[69] Daniyan, I. A., Mpofu, K. and Adeodu, A. O. (2019). Investigating the Effect of Carbon Steel STKM13a Thermal Properties during Welding Assembly of Rail Car Suspension System. Procedia CIRP, 81:886-891. Scopus Indexed.
[70] Daniyan, O. L., Ezechi, N., Daniyan, I. A., Okere, B. (2019). Development and Optimization of an Automated Irrigation System. Journal of Automation, Mobile Robotics & Intelligent Systems, 13(1):37-45. DOI: 10.14313/JAMRIS_1-2019/5. Scopus Indexed.
[71] Daniyan, I. A., Daniyan, O. L., Mpofu, K. and Ramatsetse, B. I. (2019). Development and Performance Evaluation of Automated Irrigation System. Published Proceedings of the SAUPEC/RobMech/PRASA Conference Bloemfontein, South Africa, January 28-30, 29. Added to IEEE Xplore, 978-1-7281-0369-3/19. pp. 12-16. Scopus Indexed.
[72] Daniyan, I. A., Mpofu, K., Adeodu, A. O. and Daniyan, O. L. (2019). Model Design, Simulation and Control of Rail car Suspension System. Published Proceedings of the 2019 IEEE 10th International Conference on Mechanical and Intelligent Manufacturing Technologies (ICMIMT 2019). IEEE 978-1-5386-7972-2/19. pp. 37-42. Scopus Indexed.
[73] Adeodu, A. O., Bodunde, O. P., Daniyan, I. A., Omitola, O. O., Akinyoola, J. O. and Adie, U. C. (2019). Development of an Autonomous Mobile Plant Irrigation Robot for Semi Structured Environment. Procedia Manufacturing 35:9–15. Scopus Indexed.
[74] Daniyan I. A., Mpofu K., Adeodu A. O. and Azeez T. M. (2019). Investigating the Quality and Conformity of Carbon Steel AISI 1035 under Varying Heat Treatment Conditions. Procedia Manufacturing 35:1111–1116. Scopus Indexed.
[75] Daniyan, I. A., Daniyan, O. L., Adeodu, A. O. Uchegbu, I. D. and Mpofu, K. (2019). Performance Evaluation of Smart Multi feedstock Plant. Procedia Manufacturing 35: 1117–1122. Scopus Indexed.
[76] Daniyan, I. A., Daniyan, O. L., Abiona, O. H. and Mpofu, K. (2019). Development and Optimization of a Smart System for the Production of Biogas using Poultry and Pig Dung. Procedia Manufacturing 35:1190–1195. Scopus Indexed.
[77] Giovani M. M., Mpofu, K. and Daniyan, I. A. (2019). Statistical Analysis of Determinant Factors and Framework Development for the Optimal and Sustainable Design of Municipal Solid
Waste Management Systems in the Context of Industry 4. 0. Procedia CIRP 84:245–250. Scopus Indexed.
[78] Daniyan, I. A., Mpofu, K., Daniyan, O. L., Adeodu, A. O. and Uchegbu, I. D. (2019). Design and Modelling of Automated Reactor for the Production of Caustic Potash from Cocoa Pod Husk. Procedia CIRP 84:960–965. Scopus Indexed.
[79] Phokobye, S.N., Daniyan, I. A., Tlhabadira, I. A., Masu, L. and Van Staden, L. R. (2019). Model Design and Optimization of Carbide Milling Cutter for Milling Operation of M200 Tool Steel. Procedia CIRP 84:954–959. Scopus Indexed.
[80] Daniyan, I. A., Mpofu K., Fameso, F. O., Adeodu, A. O. and Bello, K. A. (2019). Development and Simulation of Isotropic Hardening for AISI 1035 for Weld Stress Prediction during Design and Welding Assembly of the Lower Bracket of Rail Cars. Procedia CIRP 84:916–922. Scopus Indexed.
[81] Tlhabadira, I. A., Daniyan, I. A., Masu, L. and Van Staden, L. R. (2019). Process Design and Optimization of Surface Roughness during M200 TS Milling Process using the Taguchi Method. Procedia CIRP 84:868–873. Scopus Indexed.
[82] Daniyan, I. A., Tlhabadira, I., Daramola, O. O. and Mpofu K. (2019). Design and Optimization of Machining Parameters for Effective AISI P20 Removal Rate during Milling Operation. Procedia CIRP 84:861–867. Scopus Indexed.
[83] Daramola, O. O., Tlhabadira, I. , Olajide, J. L., Daniyan, I. A., Sadiku, E. R. and Masu, L. (2019). Process Design for Optimal Minimization of Resultant Cutting Force during the Machining of Ti-6Al-4V: Response Surface Method and Desirability Function Analysis. Procedia CIRP 84:854–860. Scopus Indexed.
[84] Oyesola, M. O., Mpofu, K. Mathe, N. R. and Daniyan, I. A. (2019). Development of an Integrated Design Methodology Model for Quality and throughput of Additive Manufacturing processes. Procedia CIRP 84:688–693. Scopus Indexed.
[85] Daniyan, I. A., Tlhabadira, I., Phokobye, S. N., Siviwe, M. and Mpofu K. (2019). Modelling and Optimization of the Cutting Forces during Ti6Al4V Milling Process Using the Response Surface Methodology and Dynamometer. MM Science Journal: pp. 3353-3363. Scopus Indexed.
[86] Adeodu, A. O., Daniyan, I. A., Raji, O. R., Bello, K. A. and Oloyede, O. R. (2019). Development of a Small-Scale Vertical Axis Wind Turbine for Generation of Compressed Air for Pneumatic Systems. Journal of Physics: Conference Series, 1378 (022005):1-13. doi:10.1088/1742-6596/1378/2/022005. Scopus Indexed.
[87] Adeodu, A. O., Akinola, S. O., Daniyan, I. A., Akinlosola, D. O., Oloyede, O. R. and Alufa, O. O. (2019). Development and Performance Evaluation of Thermostat Controlled Rotary Dryer for Agricultural Produce. Journal of Physics: Conference Series, 1378 (022028):1-18. doi:10.1088/1742-6596/1378/2/022028. Scopus Indexed.
[88] Oladapo, B. I., Daniyan, I. A., Ikumapayi, O. M., Malachi, O. B. and Malachi, I. O. (2020). Microanalysis of Hybrid Characterization of PLA/cHA Polymer Scaffolds for Bone Regeneration. Journal of Polymer Testing, 83:106341. Scopus Indexed.
[89] Zeferino, E. F. S., Mpofu, K. Makinde, O. A. Ramatsetse, B. I. and Daniyan, I. A. (2020). FR/CoG Multi-attribute-based Comparison Methods for Selection of the Location of a Research Institute. Journal of Facility Management, 18(1):20-35. Scopus Indexed.
[90] Daniyan, I. A., Mpofu, K. Fameso, F. O. and Adeodu, A. O. (2020). Numerical Simulation and Experimental Validation of the Welding Operation of the Railcar Bogie Frame to prevent Distortion. The International Journal of Advanced Manufacturing Technology. https://doi.org/10.1007/s00170-020-04988-6. Scopus Indexed.
[91] Daniyan, I. A., Mpofu, K. Adeodu, A. O. and Rominiyi, O. L. (2020). Investigation of Distortion, Stress and Temperature Distribution during Assembly of the Suspension System of a Rail Car. Procedia Manufacturing, 38:1792-1800. Scopus Indexed.
[92] Adesina, O. T., Jamiru, T., Daniyan, I. A., Sadiku, E. R., OgunbiyI, O. F., Adesina, O. S. and Beneke, L. W. (2020). Mechanical Property Prediction of SPS Processed GNP/PLA Polymer
Nanocomposite using Artificial Neural Network. Cogent Engineering, 7(1720894):1-17. Scopus Indexed.
[93] Daniyan, I. A., Balogun, V., Mpofu, K. and Omigbodun, F. T. (2020). An Interactive Approach towards the Development of an Additive Manufacturing Technology for Railcar Manufacturing. International Journal on Interactive Design and Manufacturing, 14:651–666,
DOI: 10.1007/s12008-020-00659-8. Scopus Indexed. [94] Daniyan, I. A., Tlhabadira, I., Mpofu, K. and Adeodu, A. O. (2020). Process design and
optimization for the milling operation of aluminum alloy (AA6063 T6), Materials Today: Proceedings, https://doi.org/10.1016/j.matpr.2020.02.396. Scopus Indexed.
[95] Letwaba, L. J., Tlhabadira, I., Daniyan, I. A., Seerana, M., Sadiku, E. R., Masu, L. (2020). Development and Microstructural Analysis of beta-SiAlONs produced by Spark Plasma Sintering. Materials Today: Proceedings, https://doi.org/10.1016/j.matpr.2020.03.127. Scopus Indexed.
[96] Daniyan, I. A., Mpofu, K., Adeodu, A. O. and Bello, K. A. (2020). The Use of Adaptive Fuzzy-PID for Vibration Control in the Suspension System of a Railcar. 2020 IEEE 11th International Conference on Mechanical and Intelligent Manufacturing Technologies. Added IEEE Xplore, pp. 130-134. Scopus Indexed.
[97] Daniyan, I. A., Tlhabadira, I., Phokobye, S. N., Mrausi, S., Mpofu, K. and Masu, L. (2020). Modelling and Optimization of the Cutting Parameters for the Milling Operation of Titanium Alloy (Ti6Al4V). 2020 IEEE 11th International Conference on Mechanical and Intelligent Manufacturing Technologies (ICMIMT 2020). Added to IEEE Xplore, pp. 68-73. Scopus Indexed.
[98] Daniyan, I. A., Mpofu, K., Adeodu, A. O. and Momoh, O. (2020). Development of a 12 kW-
Capacity Gasifier for Domestic and Experimental Applications. 2020 Southern African
Universities Power Engineering Conference/Robotics and Mechatronics/Pattern Recognition
Association of South Africa (SAUPEC/RobMech/PRASA). Added to IEEE Xplore, pp. 68-73.
DOI: 10.1109/SAUPEC/RobMech/PRASA48453.2020.9040963 Scopus Indexed. [99] Tlhabadira, I., Daniyan, I. A., Masu, L. and Mpofu, K. (2020). Development of a Model for the
Optimization of Energy Consumption during the Milling Operation of Titanium Alloy (Ti6Al4V). Materials Today: Proceedings, https://doi.org/10.1016/j.matpr.2020.03.477. Scopus Indexed.
[100] Adeodu, A. O., Adeleke, A. O., Adediran, A. A., Ikubanni, P. P., Daniyan, I. A. (2020). Effect of silver nanoparticle (AgNp) on mechanical and microstructural properties of aluminium 6063 alloy. Materials Today: Proceedings, https://doi.org/10.1016/j.matpr.2020.03.153. Scopus Indexed.
[101] Daniyan, I. A., Mpofu, K., Daniyan, O. L., Fameso, F. and Oyesola, M. (2020). Computer Aided Simulation and Performance Evaluation of Additive Manufacturing Technology for Component Parts Manufacturing. The International Journal of Advanced Manufacturing Technology, https://doi.org/10.1007/s00170-020-05340-8. Scopus Indexed.
[102] Daniyan, I. A., Mpofu, K., Oyesola, M., Ramatsetse, B. I. and Adeodu, A. O. (2020). Artificial
Intelligence for Predictive Maintenance in the Railcar Learning Factories. Procedia Manufacturing, 45:13-18.
[103] Daniyan, I. A., Mpofu, K., Adeodu, A. O. and Adesina, O. (2020). Development of Carbon
fibre Reinforced Polymer Matrix Composites and Optimization of the Process Parameters for
Railcar Applications. Materials Today: Proceedings, https://doi.org/
10.1016/j.matpr.2020.03.480. Scopus Indexed.
[104] Adeodu, A. O., Mudashiru, L., Daniyan, I. A. and Awodoyin, A. (2020). Effect of Silver
Nanoparticle (AgNp) mixed with Calcium Carbonate on Impact, Hardness and Tensile strength
Properties of Aluminium 6063. Journal of Composite Materials, 1–9. DOI:
10.1177/0021998320923141. Scopus Indexed.
Book Published [1]
[1] Omitola, O. O., Daniyan, I. A., Okafor, C. O. Awofadeju, O. A. and Olagbende (2014). New
Generation Basic Science and Technology for Junior Secondary Schools. New Generation
Books and Communication Publishing, Ibadan, Nigeria.
Book Chapter [3]
[1] Daniyan, I. A., Oyesola, M. O. Mpofu, K. and Nwankwo, S. (2019). Application of the Fourth Industrial Revolution for High Volume Production in the Rail Car Industry: Mass Production
Processes: Anil Akdogan (Ed.) Publisher: IntechOpen, Ltd., UK. http://dx.doi.org/10.5772/intechopen.88703. pp. 1-15. ISBN 978-1-83880-216-5.
[2] Daniyan, I. A. and Mpofu, K. (2019). Vibration Analysis and Control in the Rail Car
System Using PID Controls “Noise and Vibrations Control: From Theory to Practice”
Ehsan Noroozinejad Farsangi (Ed.) Publisher: IntechOpen, Ltd., UK. ISBN 978-1-78984-771-0.
[3] Daniyan, I. A. and Mpofu, K. (2018). Design for Manufacture and Assembly: Development of a Multi feedstock Biodiesel Processor. “Application of Design for Manufacturing and Assembly” Ancuta Carmen Păcurar (Ed.), Publisher: IntechOpen, Ltd., UK, DOI: intechopen.75475. pp. 1-23.
Technical Reports [3]
[1] Daniyan, I. A., Adetoro, K. A., Oluwaremi, E. M. and Oladejo, G. A. (2010). Assessment of the
Quality of Cables Produced at Denki Wires and Cables Limited, Akure, Ondo State. [2] Daniyan, I. A. (2013). Development of a Processor for Biodiesel Production. Submitted to the
Council for the Regulation of Engineering in Nigeria (COREN). [3] Oguntuase, O. B., I. A. Daniyan and A. O. Adeodu (2014). Design and Fabrication of Burglary
and Assembly of Aluminium Window Frame. Students’ Work Experience Programme, Afe Babalola University, Ado Ekiti. Published in Int’l Journal of Innovative Research in Science, Engineering and Technology. Vol., 2, Issue 12 pp. 7930-7940.
Conference Proceedings [65]
[1] Madavha, L., Laseinde, O. T., Daniyan, I. A. and Mpofu, K. (2020). Functional design and
performance evaluation of a metal handheld detector for land mines detection. 30th CIRP Design
Conference, Held between 5th-8th May, 2020 in Pretoria, South Africa.
[2] Adeodu, A. O., Daniyan, I. A., Omitola, O. O., Ejimuda, C. Esoso, A. Akinola, O. (2020). An adaptive
Industrial Internet of things (IIOts) based technology for prediction and control of cavitation in
centrifugal pumps30th CIRP Design Conference, Held between 5th-8th May, 2020 in Pretoria, South
Africa.
[3] Daniyan, I. A., Tlhabadira, I., Adeodu, A. O., Phokobye, S. N. and Mpofu, K. Process design and
modelling for milling operation of titanium alloy (Ti6Al4V) Using the Taguchi method. 30th CIRP
Design Conference, Held between 5th-8th May, 2020 in Pretoria, South Africa.
[4] Tlhabadira, I., Daniyan, I. A., Masu, L. and Mpofu, K. (2020). Process Design and Modelling for
Effective Milling Operation of Titanium Alloy (Ti6Al4V). 30th CIRP Design Conference, Held between
5th-8th May, 2020 in Pretoria, South Africa.
[5] Daniyan, I. A., Mpofu, K., Oyesola, M. O., Adeodu, A. O. and Ramatsetse, B. I. (2020). Artificial
intelligence for predictive maintenance in the railcar learning factories. 10th Conference on Learning
Factories, Graz, Austria. Held between 16th-17th April, 2020 in Graz, Austria
[6] Daniyan, I. A., Mpofu, K., Adeodu, A. O. and Momoh, O. (2020). Development of a 12 kW-Capacity
Gasifier for Domestic and Experimental Applications. 2020 Southern African Universities Power
Engineering Conference/Robotics and Mechatronics/Pattern Recognition Association of South
Africa (SAUPEC/RobMech/PRASA). Held at University of Cape Town, South Africa, between
29-31 January 2020.
[7] Daniyan, I. A., Tlhabadira, I., Phokobye, S. N., Mrausi, S., Mpofu, K. and Masu, L. (2020). Modelling
and Optimization of the Cutting Parameters for the Milling Operation of Titanium Alloy (Ti6Al4V).
2020 IEEE 11th International Conference on Mechanical and Intelligent Manufacturing
Technologies (ICMIMT 2020) Held between 20-23rd January at Cape Town, South Africa.
[8] Daniyan, I. A., Mpofu, K., Adeodu, A. O. and Bello, K. (2020). The use of Adaptive Fuzzy-PID for
Vibration Control in the Suspension System of a Railcar. 2020 IEEE 11th International Conference
on Mechanical and Intelligent Manufacturing Technologies (ICMIMT 2020) Held between 20-23rd
January at Cape Town, South Africa.
[9] Daniyan, I. A., Adeodu, A. O. and Mpofu K. (2019). Use of Central Composite Design and Artificial
Neural Network for Predicting the Yield of Biodiesel. 4th CIRP Conference on Biomanufacturing held
between Dec. 12-15, 2019 at Guangzhou, China.
[10] Daniyan, I. A., Balogun, A. V., Adeodu, A. O., Jacobs, K., Oyesola, M. and Mpofu K. (2019).
Development of a Robot for Lawn Mowing. 8th International Conference on Through-Life
Engineering Services. TESConf 2019. Held between October 27-29, Cleveland, Ohio, USA.
[11] Oyesola, M., Mpofu K., Mathe, N. R. Daniyan, I. A. (2019). Hybrid-additive manufacturing cost
model: A sustainable Through-Life Engineering support for Maintenance Repair Overhaul in the
Aerospace. 8th International Conference on Through-Life Engineering Services. TESConf 2019. Held
between October 27-29, Cleveland, Ohio, USA.
[12] Daniyan, I. A. and Mpofu, K. (2019). The Development of the Rail Industry with the Application of
the Elements of the 4th Industrial Revolution. Presented at the University of South Africa, South
Africa Industrial Engineering and Robotics Symposium hosted by UNISA’s Department of
Mechanical and Industrial Engineering between 23-24 October, 2019.
[13] Tlhabadira, I. A., Daniyan, I. A. Phokobye, S. N., Siviwe, M. and Mpofu, K. (2019). Process Design
for Effective Milling Operations of Titanium Alloy (Ti6Al4V). Presented at the University of South
Africa, South Africa Industrial Engineering and Robotics Symposium hosted by UNISA’s Department
of Mechanical and Industrial Engineering between 23-24 October, 2019.
[14] Daniyan, I. A., Tlhabadira, I., Phokobye, S. N., Siviwe, M. and Mpofu K. (2019). Process Design,
Modelling and Simulation of Cutting Force during the Milling Operation of Titanium alloy Ti6Al4V.
Conference of High Speed Machining held in Czech Republic between October 7-10, 2019.
[15] Daniyan, I. A., Mpofu K., Fameso, F. O., and Adeodu, A. O. Simulation of Kinematic Hardening
Models for Carbon Steel AISI 1035 Weld Stress Prediction during Welding Assembly of a Rail Car.
17th Global Conference on Sustainable Manufacturing held in Shanghai China, between October 9-
11, 2019.
[16] Mozambe, G. M., Mpofu, K. and Daniyan, I. A. (2019). Comparative Analysis of Optimization
Models Application in Household Waste Management Systems. Conference of the Southern African
Institute of Industrial Engineering, Held in Port Elizabeth Between 30 September- 2 October 2019.
[17] Daniyan I. A., Mpofu, K. and Adeodu, A. O. (2019). The Use of Analytical Hierarchy Process (AHP)
for Welding Process Selection during Rail Car Manufacturing. Conference of the Southern African
Institute of Industrial Engineering, Held in Port Elizabeth Between 30 September- 2 October 2019.
[18] Daniyan I. A., Adeodu, A. O., Idris, K. and Mpofu, K. (2019). Development and Performance
Evaluation of the Humidity Measurement Bench. Conference of the Southern African Institute of
Industrial Engineering, Held in Port Elizabeth Between 30 September- 2 October 2019.
[19] Daniyan, I. A., Mpofu, K. and Adeodu, A. O. Simulation and Control of the Oscillatory Response of
Railcar Suspension System using Advance Controls. Presented at the 6th SA-UNESCO Engineering
Science and Technology Conference held at the North West University, Mafikeng Campus between
26-27th September, 2019.
[20] Tlhabadira, I., Daniyan, I. A., Phokobye, S. N., Siviwe, M. and Mpofu K. (2019). Process Design,
and Optimization for Effective Milling Operation of Titanium alloy Ti6Al4V. Presented at the 6th SA-
UNESCO Engineering Science and Technology Conference held at the North West University,
Mafikeng Campus between 26-27th September, 2019.
[21] Daniyan, I. A., Tlhabadira, I., Daramola, O. O., Phokobye, S. N., Siviwe, M. and Mpofu, K. (2019).
Measurement and Optimization of Cutting Forces during M200 TS Milling Process Using the
Response Surface Methodology and Dynamometer. Presented at the 13th CIRP International
Conference on Intelligent Computation in Manufacturing Engineering. Held between 17-19th July,
2019, Naples, Italy.
[22] Adeodu, A. O., Akinola, S. O., Daniyan I. A., Oloyede O. R., Akinlosola D. O. and Alufa O. O. (2019).
Development and Performance Evaluation of Thermostat Controlled Rotary Dryer for Agricultural
Produce. 3rd Int’l Conference on Engineering for a Sustainable World (ICESW, 2019). Held between
July 3-5, 2019 at Covenant University, Otta, Ogun State, Nigeria.
[23] Adeodu A. O., Daniyan, I. A., Raji O. R., Bello K. A. and Oloyede O. R. (2019). Development of a
Small-scale Vertical-axis Wind Turbine for Generation of Compressed Air for Pneumatic Systems. .
3rd Int’l Conference on Engineering for a Sustainable World (ICESW, 2019). Held between July 3-5,
2019 at Covenant University, Otta, Ogun State, Nigeria.
[24] Daniyan, I. A., Mpofu, K., Adeodu, A. O. and Rominiyi, O. L. (2019). Investigation of Distortion,
Stress and Temperature Distribution during Assembly of the Suspension System of a Rail Car. 29th
International Conference on Flexible Automation and Intelligent Manufacturing (FAIM2019), June
24-28, 2019, Limerick, Ireland.
[25] Daniyan, I. A., Mpofu, K. and Adeodu, A. O. (2019). Investigating the Effect of Carbon Steel
STKM13a Thermal Properties during Welding Assembly of Rail Car Suspension System. 52nd CIRP
Manufacturing Systems Conference 2019, Slovenia between 12-14th June, 2019.
[26] Daniyan, I. A., Mpofu, K. and Adeodu, A. O. (2019). Development of a Framework for Improving
the Quality and conformity of Carbon Steel AISI 1070 for Railcar Applications. Presented at the 2nd
African Operations Management Conference, University of South Africa, held between 4- 6th June,
2019.
[27] Daniyan, I. A., Mpofu, K. and Akinbowale E. O. (2019). Design and Optimization of Process
Parameters for the Production of Caustic Potash from Cocoa Pod Husk. Presented at the 2nd African
Operations Management Conference, University of South Africa, held between 4-6th June, 2019.
[28] Daniyan, I. A., Akinbowale E. O. and Mpofu, K. (2019). Development of Mathematical Models for
Effective Supply Chain Management in the Railcar Industry. Presented at the 2nd African
Operations Management Conference, University of South Africa, held between 4-6th June, 2019.
[29] Daniyan, I.A., Dahunsi, O. A, Oguntuase, O. B., Daniyan O. L., and Mpofu, K. (2019). Development
of a Prototype Test Rig for Leak Detection in Pipelines. Presented at the 26th CIRP Life Cycle
Engineering (LCE) Conference, Purdue University, USA, 8-10th May, 2019.
[30] Tlhabadira, I., Daniyan, I. A., Masu, L. and VanStaden L. R. (2019). Process Design and
Optimization of Surface Roughness during M200 TS Milling Process using the Taguchi Method.
Presented at the 29th CIRP Design Conference, 8-10 May, 2019, Póvoa de Varzim, Portugal.
[31] Phokobye, S. N., Daniyan, I. A. Tlhabadira, I., Masu, L. and VanStaden L. R. (2019). Model Design
and Optimization of Carbide Milling Cutter for Milling Operation of M200 Tool Steel. Presented at
the 29th CIRP Design Conference, 8-10 May, 2019, Póvoa de Varzim, Portugal.
[32] Daniyan, I. A., Tlhabadira, I., Daramola, O. O. and Mpofu K. (2019). Design and Optimization of
Machining Parameters for Effective AISI P20 Removal Rate during Milling Operation. Presented at
the 29th CIRP Design Conference, 8-10 May, 2019, Póvoa de Varzim, Portugal.
[33] Daniyan, I. A., Mpofu K. , Fameso, F. O., Adeodu, A. O. and Bello, K. A.(2019). Development and
Simulation of Isotropic Hardening for AISI 1035 Weld Stress Prediction during Design and Welding
Assembly of Lower Brackets of Rail Cars. Presented at the 29th CIRP Design Conference, 8-10 May,
2019, Póvoa de Varzim, Portugal.
[34] Daniyan, I. A. Mpofu, K., Daniyan, L. and Adeodu, A. O. (2019). Design and Optimization of
Automated Reactor for the Production of Caustic Potash from Cocoa Pod Husk. . Presented at the
29th CIRP Design Conference, 8-10 May, 2019, Póvoa de Varzim, Portugal.
[35] Daramola, O.O., Tlhabadira, I., Olajide, J.L., Daniyan, I.A, Sadiku, E.R., Masu, L. d, VanStaden L. R.
(2019). Process Design for Optimal Minimization of Resultant Cutting Force during the Machining
of Ti-6Al-4V: Response Surface Method and Desirability Functional Analysis. Presented at the 29th
CIRP Design Conference, 8-10 May, 2019, Póvoa de Varzim, Portugal.
[36] Oyesola, M. O., Mpofu, K., Mathe, N. and Daniyan, I. A. (2019). Development of an Integrated
Design Methodology Model for Quality and throughput of Additive Manufacturing Processes.
Presented at the 29th CIRP Design Conference, 8-10 May, 2019, Póvoa de Varzim, Portugal.
[37] Monzambe, G. M., Mpofu, K. and Daniyan, I. A. (2019). Statistical Analysis of Determinant Factors
for the Optimal and Sustainable Design of Municipal Solid Waste Management Systems in the
Context of Industry 4.0. Presented at the 29th CIRP Design Conference, 8-10 May, 2019, Póvoa de
Varzim, Portugal.
[38] Daniyan, I. A. Daniyan, O. L., Abiona, O. H. and Mpofu, K. (2019). Development and Optimization
of a Smart System for the Production of Biogas using Poultry and Pig Dung. First International
Conference on Sustainable Materials Processing and Manufacturing, SMPM 2019, Sun City Resort,
South Africa, 08 – 10 March 2019.
[39] Daniyan, I. A., Daniyan, O. L., Adeodu, A. O., Uchegbu, I. D. and Mpofu, K. (2019). Performance
Evaluation of a Smart Multi feedstock Biodiesel Plant. International Conference on Sustainable
Materials Processing and Manufacturing, SMPM 2019, Sun City Resort, South Africa, 08 – 10 March
2019.
[40] Daniyan, I. A., Mpofu, K. Adeodu, A. O. and Azeez, T. M. (2019). Investigating the quality and
conformity of carbon steel AISI 1035 under varying heat treatment conditions. First International
Conference on Sustainable Materials Processing and Manufacturing, SMPM 2019, Sun City Resort,
South Africa, 08 – 10 March 2019.
[41] Adeodu, A. O., Bodunde, O. P., Daniyan, I. A., Omitola, O. O., Akinyoola, J. O., and Adie, U. C.
(2019). Development of an Autonomous Mobile Plant Irrigation Robot for Semi-Structured
Environment. First International Conference on Sustainable Materials Processing and
Manufacturing, SMPM 2019, Sun City Resort, South Africa, 08 – 10 March 2019.
[42] Daniyan, I. A., Mpofu, K. Adeodu, A. O. and Daniyan O. L. (2019). Model Design, Simulation and
Control of Rail car Suspension System. 2019 IEEE 10th International Conference on Mechanical and
Intelligent Manufacturing Technologies (ICMIMT 2019) Held between 15-17th February at Cape
Town, South Africa.
[43] Daniyan, I. A., Daniyan, O. L., Mpofu, K. and Ramatsetse, B. (2019). Development and
Performance Evaluation of Automated Irrigation System. 2019 SAUPEC/ROBMEC/PRASA SAIEEE
International Conference Held at Central University of Technology, Bloemfontein, Free State, South
Africa between 28th-30th January, 2019.
[44] Daniyan, I. A. and Mpofu, K. (2018). Investigating the Effect of Carbon Steel SKTM13a Thermal
Properties during Welding Assembly of Rail Car Suspension System. Presented at the CIE48
Proceedings, 2-5 December 2018, The University of Auckland, New Zealand.
[45] Daniyan, I. A., Mpofu, K., Adeodu, A. O. and Azeez, T. M. (2018). Design of Efficient Welding
Process for Rail Car Bracket Assembly using Taguchi and Response Surface Methodology. Presented
at the 8th International Conference on Appropriate Technology held between 22nd-25th
November, 2018 at Songhaï Center, Songhaï Center, Porto-Novo, Benin Republic.
[46] Daniyan, I. A., Uchegbu, I. D., Ibekwe, K. S., Daniyan, O. L. and Mpofu, K. (2018). Development of
Energy Efficient Multi-Crop Tray Dryer. Presented at the 8th International Conference on
Appropriate Technology held between 22nd-25th November, 2018 at Songhaï Center, Songhaï
Center, Porto-Novo, Benin Republic.
[47] Daniyan, I. A., Bello, E. I., Ogedengbe, T. I., Mogaji, P. B. and Mpofu, K. (2018). Development of a
Smart Multi Feedstock Biodiesel Plant. Presented at the 8th International Conference on
Appropriate Technology held between 22nd-25th November, 2018 at Songhaï Center, Songhaï
Center, Porto-Novo, Benin Republic.
[48] Daniyan, I. A., Ikuponiyi, S., Daniyan, O. L. and Adeodu, A. O. (2018). Development of a Smart
Diabetes Monitoring Device. Presented at the 8th International Conference on Appropriate
Technology held between 22nd-25th November, 2018 at Songhaï Center, Songhaï Center, Porto-
Novo, Benin Republic.
[49] Daniyan, I. A., Ahwin, K. A., Aderoba, A. A., Daniyan, O. L. and Mpofu, K. (2018). Development
and Optimization of a Smart Digester for the Production of Biogas. Presented at the First African
International Conference on Industrial Engineering and Operations Management. Held between
29th-31st October, 2018 in Pretoria, South Africa.
[50] Daniyan, I. A., Daniyan, O. L. and Mpofu, K. (2018). Design and Simulation of a Controller for
Active Suspension System of a Rail Car. Presented at the First African International Conference on
Industrial Engineering and Operations Management. Held between 29th-31st October, 2018 in
Pretoria, South Africa.
[51] Daniyan, I. A., Adeodu, A. O., Daniyan, O. L. Ajetomobi, O. R. and Mpofu, K. (2018). Development
of a Reconfigurable Assembly Fixture. Presented at the First African International Conference on
Industrial Engineering and Operations Management. Held between 29th-31st October, 2018 in
Pretoria, South Africa.
[52] Daniyan, I. A. and Mpofu, K. (2018). Design and Simulation of a Reconfigurable Hydraulic Press
Brake. 11th ICEBE & 7th ICIE & PEESA Ill International Conference on Engineering and Business
Education, Innovation and Entrepreneurship and Capacity Building in Higher Education, Held
between 15th -19th October, 2018 at University of Szczecin, Poland.
[53] Daniyan, I. A., Akinbowale, O. E. and Mpofu, K. (2018). Use of Automated Systems and ICT in
Combating Corruption in the Manufacturing Industries. Presented at the ASSAf Annual Young
Scientist Conference 2018. Held between 13th -14th September, 2018 at OR Tambo Gauteng, South
Africa.
[54] Daniyan, I. A. and Mpofu, K. (2018). Investigation of Distortion and Temperature Distribution
during Assembly of Suspension Arm of a Rail Car. Proceedings of the 6th International of Conference
on Capacity Building for National Sustainable Development (CBNSD). Held between 29th -31st
August, 2018, at Multimedia University, Nairobi, Kenya. pp. 651-657.
[55] Daniyan, I. A., Dada, O. M., Adeodu, A. O., Uchegbu, I .D., Isijola, O. O. and Mpoku, K. (2018).
Development and Performance Evaluation of a Humidifier Cooling System for Room Ventilation.
Proceedings of the 6th International of Conference on Capacity Building for National Sustainable
Development (CBNSD). Held between 29th -31st August, 2018, at Multimedia University, Nairobi,
Kenya. pp. 478-484.
[56] Daniyan, I. A., Daniyan, O. L., Adeodu, A. O., Ojaokomo, F. and Mpofu, K. (2018). Development of
Smart Alert System for Human Access into Premises. Proceedings of the 6th International of
Conference on Capacity Building for National Sustainable Development (CBNSD). Held between
29th -31st August, 2018, at Multimedia University, Nairobi, Kenya. pp. 531-542.
[57] Adeodu, A. O., Daniyan, I. A., Ebimoghan, T. S. and Akinola, A. O. (2018). Development of an
Embedded Obstacle Avoidance and Path Planning Autonomous Solar Grass Cutting Robot for Semi-
Structured Environment. Proceedings of the 7th IEEE International Conference of Adaptive Science
and Technology. Held between August 22-24, 2018 at University of Ghana, Accra, Ghana.
[58] Daniyan, I. A., Daniyan, O. L., Adeodu, A. O., Uchegbu, I. D., Ibekwe, K. S. and Mpofu, K. (2018).
Design and Simulation of a Wind Turbine for Electricity Generation. Proceedings of International
Conference on Topical Transcends in Science, Technology & Management and Sai Vidya Institute of
Technology and Institute for Exploring Advances in Engineering. Held between 17th and 18th
August, 2018, at Bengaluru, India.
[59] Daniyan, I. A., Bello, E. I., Ogedengbe, T. I. and Mogaji, P. B. (2018). Gas Chromatography of Used
Frying Oil and Its Biodiesel. Proceedings of the FUTA SEET Int’l Conference held between 17th - 19th
July, 2018 at The Federal University of Technology, Akure, Nigeria. pp. 23.
[60] Daniyan, I. A. and Oguntuase, O. B. (2018). Production of Biodiesel from Palm Olein Oil Using
Heterogeneous Transesterification Method. Proceedings of the FUTA SEET Int’l Conference held
between 17th -19th July, 2018 at The Federal University of Technology, Akure, Nigeria. pp. 22.
[61] Daniyan, I. A., Bello, E. I., Ogedengbe, T. I., Lajide, L. and Mogaji, P. B. (2017). Emission
Characteristics of Diesel and Biodiesel Blends: A Review. Proceedings of the FUTA SEET Int’l
Conference held between 11th -13th July, 2017 at The Federal University of Technology, Akure,
Nigeria. pp. 94-105.
[62] Daniyan, I. A., Bello, E. I., Ogedengbe, T. I., Lajide, L. and Mogaji, P. B. (2017). “Use of Artificial
Neural Network for Correlating the Process Parameters and Prediction of Biodiesel Yield”.
Proceedings of the 7th Annual and International Conference of the Renewable and Alternative
Energy Society of Nigeria (RAESON). Held between 15th -18th August, 2017 At The Federal
University of Technology, Akure, Nigeria.
[63] Daniyan, I. A., Bello, E. I., Ogedengbe, T. I., Lajide, L. and Mogaji, P. B. (2016). Development of a
Model for Predicting the Yield of Biodiesel during Biodiesel Production. Proceedings of the FUTA
SEET International Conference Held between 16th -18th August, 2016 at The Federal University of
Technology, Akure, Nigeria.
[64] Daniyan, I. A., Daniyan, O. L. and Adeodu, A. O. (2014). e- Learning in Manufacturing Industries.
Presented at the 9th Engineering Conference: e-Learning in Education. Held between 12-15th
August, 2014 at Federal Polytechnic, Ado Ekiti, Nigeria.
[65] Bello, E. I., Ogedengbe, T. I. and Daniyan, I. A. (2012): Development of a Processor for Biodiesel
Production. (ICERD 12003). Presented at the Fourth International Conference of Engineering
Research and Development: Advances in Engineering, Science and Technology, (ICERD 2012). Held
between 4th-6th June, 2012 at University of Benin, Benin City, Nigeria.
LECTURES AS GUEST SPEAKER [3]
[1] Daniyan, I. A. (2018). Use of Automated Systems and ICT in Combating Corruption in the
Manufacturing Industries. Presented at the ASSAf Annual Young Scientist Conference 2018. Held
between 13th -14th September, 2018 at OR Tambo Gauteng, South Africa.
[2] Daniyan, I. A. (2019). Helping Rail People and Companies Learn, Transmit and Develop by
Promoting Innovation and Careers In the Railway Sector. Lecture delivered at 2019 African Rail
Conference and Exhibition, held Johannesburg, South Africa on 20th June, 2019.
[3] Daniyan, I. A. (2019). Supply Chain Security and Managing Third Part Risk in the Rail Industry.
Lecture delivered at 2019 African Rail Conference and Exhibition, held at Johannesburg, South
Africa on 20th June, 2019.
Seminar/Colloquium
[1] Daniyan, I. A. (2018). Development of a Controller for the Active Suspension System of a Rail Car.
Presented at Department of Industrial Engineering GROWS seminar, Tshwane University of
Technology on 15th June, 2018.
[2] Daniyan, I. A. (2017). Development and Optimization of a Multi Feedstock Biodiesel Plant.
Presented at The Federal University of Technology, Akure, Ondo State, Nigeria on 2nd February,
2017.
[3] Daniyan, I. A. (2016). Development of a Multi Feedstock Biodiesel Plant. Ph. D Final Seminar
Presented at The Federal University of Technology, Akure, Ondo State, Nigeria on 4th August, 2016.
Certification
[1] National Instrument Certification (LABVIEW core I & II) (2014).
Boards and Committee
[1] Academic Director, Department of Mechanical & Mechatronics Engineering, Afe Babalola
University, Ado Ekiti, Nigeria. (2013-2018)
[2] Member, Thermofluids Laboratory Committee, Department of Mechanical & Mechatronics
Engineering, Afe Babalola University, Ado Ekiti, Nigeria. (2013-2018)
[3] Editorial Member, International Journal of Science and Research (IJSR) (2013 till date)
[4] Reviewer Panel Member, International Journal of Scientific Engineering and Research
(2003–till date).
[5] Member, Production Engineering Lab Committee, Department of Mechanical & Mechatronics
Engineering, Afe Babalola University, Ado Ekiti, Nigeria. (2014-2018)
[6] Member, Committee for Development of Machinery for Organic Fertilizer Production, Department
of Mechanical & Mechatronics Engineering, Afe Babalola University, Ado Ekiti, Nigeria.
(2015-2018)
[7] Member, Committee for Small Scale Refinery Plant, Directorate for Technological Development,
Afe Babalola University, Ado Ekiti, Nigeria. (2016-2018)
[8] Member, Energy Research Committee, Department of Mechanical & Mechatronics Engineering,
Afe Babalola University, Ado Ekiti, Nigeria. (2017-2018)
[9] Editorial Member, AR Research Publication and Conference World (2017 till date)
[10] Editorial Board Member, Journal of Mechanical Engineering (2018 till date)
[11] Member, Research team on Reconfiguration. Department of Industrial Engineering, Tshwane
University of Technology, Pretoria, South Africa (2018-till date)
[12] Member, Scientific and Review Committee, CIRP Procedia (2018-till date)
[13] Member, Local Organizing Committee, CIRP Design 2020 (2019-till date)
[14] Member, Local organizing Committee, International Conference on Appropriate Technology (ICAT
2020) (2019-till date)
[15] Member, organizing Committee, International Conference on Electronics and Electrical
Engineering, ICEEE, Seoul, 2020 (2019-till date)
Bachelor (B. Eng.) Under graduate Supervision (18)
S/N Name of Student Project Title Status Supervision role
1. ELEMURE, Ifeoluwa
Emmanuel
Development of a Model for Predicting
the Due Dates for Effective Machine
Delivery, Installation and Commissioning
of Machine Tools
2015;
Completed
Co- supervisor
2. OLAFARE, Ayomide
Oluwatosin
Development of Cassava Peeling Machine 2015;
Completed
Co- supervisor
3. OSADARE, Dapo
Fiyinfoluwa
Development of a Controller for Quarter-
car Active Suspension System
2015;
Completed
Co- supervisor
4. AKHERE,
Omokhuale Marcus
Development of Machinery for the
Production of Organic Fertilizers
2016;
Completed
Major
Supervisor
5. ONIBOKUN, Adedeji
William
Development of a Plastic Recycling
Machine
2016;
Completed
Major
Supervisor
6. MAYUNGBE, Elijah
Tomiwa
Development of a Belt Conveyor for Small
Scale Industries
2016;
Completed
Major
Supervisor
7. OGUNTUASE,
Oluwaseye Bolaji
Development of a Prototype Test Rig for
Oil Leakages Detection in Pipelines
2016;
Completed
Co- supervisor
8. AHWIN, Kevin
Akporode
Development and Optimization of a Smart
Biogas Plant
2017;
Completed
Major
Supervisor
9. COOKEY, Senibo Development and Optimization of a Paint
Production Machine
2017;
Completed
Co- supervisor
10. IKUPONIYI, Smart Development of a Smart Diabetes
Monitoring Device
2017;
Completed
Major
Supervisor
11. ADELABU, George Development and Optimization of a Small
Scale Biodiesel Processor
2017;
Completed
Major
Supervisor
12. UMAKHIHE, Arnold Development of a Deionizer for Water
Purification
2017;
Completed
Major
Supervisor
13. ABIONA, Hezekiah
Olufisayo
Development of a Smart Biogas Plant for
Energy Generation from Animal Waste
2018;
Completed
Major
Supervisor
14. MOMOH, Osazele Development and Optimization of Wood
Gasifier for Energy Generation
2018;
Completed
Major
Supervisor
15. IBEKWE, Samuel
Kelechi.
Development of a Multi-Crop Tray Dryer 2018;
Completed
Major
Supervisor
16. AJETOMOBI, Rufus
Olukunle
Development and Simulation of a
Reconfigurable Fixture Assembly Using
Pneumatic Control
2018;
Completed
Major
Supervisor
18. OJAOKOMO, Francis Development of a Remote Controlled Alert
System for Human Access into Premises
2018;
Completed
Major
Supervisor
Post graduate Supervision (10): Masters’ (M.Eng)
S/N Name of Student Project Title Status Supervision role
1. ADEBIYI, Adeola
Stephen
Development of an Autonomous Ground
Vehicle for Environmental
Characterization
2019;
Completed
Major
Supervisor
2. GIOVANI, Magbiti Monzambe
Conceptual Modelling for the optimal design of Municipal Solid Waste Transfer Station: A case study
2020;
Completed
Co-Supervisor
6. LE Madavha Detection Performance Analysis of the Midas Handheld Metal Detector Upgrades in Military Applications
2020;
Completed
Co-Supervisor
3. SJ Mthembu “Assembly Line Balancing: Improving Throughput and Reliability Delivery in Small Business.”
2018;
Ongoing
Co-Supervisor
4. RC Saka Customizing of Reconfigurable Assembly Fixture to Suite Small, Medium, Micro-enterprises in the Rail Industries.
2018;
Ongoing
Co-Supervisor
5. AY Magodi Effects of Quality Management System implementation on a small enterprise
2018;
Ongoing
Co-Supervisor
7. TP TSIRI Development of a Continuous Improvement Framework for the South
2019;
Ongoing
Co-Supervisor
African Mint Company
8. SN Phokobye Comparative Investigation Of The Cutting Performance Of SiAlON Ceramic Cutting Tool Developed By Spark Plasma Sintering And Injection Moulding Techniques
2019;
Ongoing
Co-Supervisor
9. KE Basitere Neural Network in Predetermined Time Standards.
2020;
Ongoing
Major-
Supervisor
10. QA Mokoena Framework For Improving Regulations for Commercial Drones in South Africa
2020;
Ongoing
Co-Supervisor
REFEREES
1. Dr. P. B. Mogaji (+2348033560260)
Associate Professor, Department of Mechanical Engineering
The Federal University of Technology, Akure, Nigeria.
E mail: [email protected]
2. Dr. Adefemi Adeodu (+2348036443415)
Senior Lecturer,
Department of Mechanical & Mechatronics Engineering, Afe Babalola University, Ado Ekiti,
Nigeria
E mail: [email protected]
3. Mr. Isaac Tlhabadira (+27670360861)
Director, Technology & Innovation
Tshwane University of Technology, Pretoria, South Africa
E mail: [email protected]
Date: 13th April, 2020 Signature:
