Do-It-Yourself P3 Arc Flash Analysis Software _ Arc Flash Engineering

30/10/2015 Do-It-Yourself P3 Arc Flash Analysis Software | Arc Flash Engineering

http://arcflashengineering.com/arc-flash-analysis-software 1/12

Arc Flash EngineeringArc Flash Compliance Made Easy! Call 1-800-381-4389

About ITU Arc FlashNews

Free StuffContact Us

Free Quote

HomeWhat is an Arc Flash?

Electrical InjuriesElectrical injury in the workplace

Arc Flash AnalysisIs an Arc Flash Hazard Analysis Required?What is NFPA 70E?Arc Flash Warning LabelsCertificate of ComplianceDo-It-Yourself Arc Flash Analysis SoftwareArc Flash Analysis Report

Our Recent Arc Flash Analysis ClientsGet a Quote

Arc Flash PPE RequirementsHazard Risk Category 1Hazard Risk Category 2Hazard Risk Category 3Hazard Risk Category 4

NFPA 70E Electrical Safety TrainingNFPA 70E Training OnlineGet a QuoteTraining Equipment

Arc Flash Analysis Terms

FAQ’s

http://arcflashengineering.com/


http://arcflashengineering.com/about-itu-arc-flash

http://arcflashengineering.com/news

http://itudownloads.com/

http://arcflashengineering.com/contact-us

http://arcflashengineering.com/free-arc-flash-quote


http://arcflashengineering.com/what-is-an-arc-flash

http://arcflashengineering.com/electrical-injuries

http://arcflashengineering.com/electrical-injury-in-the-workplace

http://arcflashengineering.com/arc-flash-analysis

http://arcflashengineering.com/is-an-arc-flash-analysis-required

http://arcflashengineering.com/the-nfpa-70e

http://arcflashengineering.com/arc-flash-warning-labels

http://arcflashengineering.com/certificate-of-compliance

http://arcflashengineering.com/arc-flash-analysis-software

http://arcflashengineering.com/arc-flash-analysis-report

http://arcflashengineering.com/arc-flash-analysis-recent-clients


http://arcflashengineering.com/arc-flash-ppe-requirements

http://arcflashengineering.com/hazard-risk-caterory-1

http://arcflashengineering.com/hazard-risk-category-2



http://arcflashengineering.com/nfpa-70e-electrical-safety-training

http://www.workersed.com/


http://trainingpanels.com/

http://arcflashengineering.com/arc-flash-analysis-terms

http://arcflashengineering.com/faqs



Arc Flash / Arc FaultHazard Risk Analysis

Electrical Safety StandardsPersonal Protective Equipment (PPE)

Safety Grounds

Approach BoundariesEnergized Electrical Work Permit

Electrical Safety EquipmentLockout-Tagout

VoltmetersElectrical Maintenance Terminology

Do-It-Yourself Arc Flash Analysis Software…

ITU provides a way to assist you in doing your own Arc Flash Analysis (Arc Flash Risk Assessment) to help you save money!

Our Arc Flash Analysis Software is an excellent way for electrical contractors and installers to leave behind a job that is in compliance with NFPA 70E and

OSHA 1910 Arc Flash Warning Regulations and Standards.

We provide this easy-to-use P3 Power Planner Arc Flash Analysis (Arc Flash Risk Assessment) Software at nocharge.

Fill out the form below for instant access to the P3 Program.

Your Name *

Business Phone *

http://arcflashengineering.com/arc-flash-arc-fault

http://arcflashengineering.com/hazard-risk-analysis

http://arcflashengineering.com/electrical-safety-standards

http://arcflashengineering.com/personal-protective-equipment-ppe

http://arcflashengineering.com/safety-grounds

http://arcflashengineering.com/approach-boundaries

http://nfpasafety.com/

http://arcflashengineering.com/electrical-safety-equipment

http://arcflashengineering.com/lockout-tagout

http://arcflashengineering.com/voltmeters

http://arcflashengineering.com/electrical-maintenance-terminology



Email *

Country *

State *

Alabama

Check the box if you agree to terms of use. *

-Terms of Use- ITU's P3 Arc Flash Analysis (Arc Flash Risk Assessment) Software is for use only in conjunction with ITU's Arc Flash Engineering service. Any

other use of this software is prohibited.

Questions or Concerns?

United States

Canada

Mexico

Other

I agree to the terms below.



For security purposes enter the code in the text box below.

Submit

This Arc Flash Analysis Software Program enables Plant and Facility Managers and Personnel to drastically reduce the cost of getting in compliance with these

new OSHA and NFPA70E standards.

ITU’s exclusive “Power Planner” Arc Flash Analysis software program (P3) allows you to enter your electrical system in an easy WYSIWYG work surface,

meaning just choose from the common elements on the toolbar and drag each item into your drawing. Double-click on each item and enter the needed dataabout the item. You’ll enter the starting point such as the utility transformer feeding your facility, the main breaker data, the wire sizes, lengths, and types. Enter

the system that you are wanting to do an Arc Flash Analysis on. Then click “submit” and the data is sent to ITU’s Professional Engineering group to conduct an

analysis on. This is a very fast, effective, and low cost way to conduct and analysis on small to mid-sized electrical systems. ITU will send you a detailed Arc

Flash Analysis report and print labels for each of your electrical panels. Or, give you the information you need to print your own labels if you have a label printer.In some cases, ITU’s engineering group can provide “Same Day Service”. This is great for electricians and contractors who need to do an analysis on

installations at a clients facility, or maintenance groups in facilities who add-on or make changes in facility electrical systems, and need to keep the facility in

compliance with the Arc Flash Regulations.

Power Planner software is a tool that allows almost anybody who is familiar with electrical equipment to gather the correct information needed for ITU Engineersto conduct an Arc Flash Analysis (Arc Flash Risk Assessment).

Simply use the software to click and drag the items into the drawing. Then enter the information that the software asks for. Do this for each item in your electrical

system. Once you’re done, submit the file to ITU and our engineers will go right to work conducting the study.

Meets NFPA and OSHA Standards

The Arc Flash Analysis (Arc Flash Risk Assessment) is conducted based on NFPA 70E and IEEE 1584 standards and exceeds the OSHA requirements. Weuse the state of the art ETAP platform to accurately and effectively model your entire electrical system based on the information you enter into the ITU Power

Planner software.

You do the leg work… We do the Engineering!When we’re done, here’s what you get:

A Comprehensive Arc Flash Analysis Report.



An Electrical One Line Diagram (DXF).OSHA & ANSI approved Warning Labels.

PPE Requirement Reports.Ability to easily stay in compliance.

Call a Project Coordinator today to get started…

Toll Free: 1-800-381-4389

More Information about the Arc Flash Regulations:

Short Circuit Fault Current and Arc Flash Hazard Analysis (Arc Flash Risk Assessment)

The National Fire Protection Association ( NFPA ) requires that every Non-Dwelling facility have conducted an Arc Flash Analysis to determine the level ofIncident Energy that a worker would be exposed to, should a short circuit or ground fault occur causing an arc blast while that worker is servicing the equipment.

OSHA cfr29 1910 using the NFPA publications such as the NFPA 70E and the NFPA 70 NEC (or better known as The National Electrical Code) as an“Industry Consensus” indicates that OSHA will use those regulations to determine if an employer acted properly during an investigation.

Deadline for OSHA compliance:

OSHA’s VCP or Voluntary Compliance Program members have been told that they have until November 2008 to get into compliance with these regulations.

The National Electrical Safety Code (NESC) states that all non-dwelling facilities have the arc flash analysis completed no later than January 1, 2009. Don’t letanother day pass without putting safety 1st in your facility. Call us today at 866-851-9993 or use our online form to request a quotation for an arc flash analysis

at your facility.

Here’s what we do:

ITU engineers have conducted IEEE 1584 and NFPA 70E based Arc Flash Analysis on thousands of electrical distribution panels at facilities all across theUnited States. Our unique process allows us to conduct the entire process with little or no interruptions to your facility or manufacturing. Our process gives us

several huge advantages. Those advantages are:

Faster Completion



Lower CostHigher AccuracyLess Interruptions

These all add up to a much safer and complete project, while allowing you more insight and control over what we are doing. Call and ask our client support teamabout how we do this… we won’t publish our methods here in view of our competition.

Arc Flash Hazards Study (Arc Flash Risk Assessment):

The arc flash study itself provides the data and information necessary to determine the level of hazard at each electrical panel or enclosure. NFPA requires thatthe following enclosures be surveyed and labeled:

Breaker Panels

Fuse PanelsMain Switch GearDistribution Panels

Branch DisconnectsMotor Control Buckets

Motor Control Panels

And any panel likely to be serviced by a worker

Each of these must be labeled with a label that meets the ANSI Z535 Standard ( American National Standards Institute ). These requirements require the label

to meet certain size, layout, content, and reliability standards.

One of the major compliance failures is that some companies are installing labels that do not meet the size requirement. Our process meets and exceeds thosestandards.

Our engineers use state of the art computer modeling to perform an accurate and comprehensive analysis. By gathering the physical data of your utility feeders,electrical distribution and protection systems, the on-site engineer will generate an interactive computer model of your entire system. The software that we utilizeis the most up-to-date software designed specifically for electrical engineering purposes and is the only software approved by AACET (American Association of

Certified Engineers and Trainers). We’ve invested tens of thousands of dollars in these computer based systems to provide you with the most accurate andcomplete services. In addition, our on-site Electrical Engineers are certified and trained specifically for this purpose.



Arc Flash Warning Labels:

Our permanent Arc Flash Warning Labels are designed to make understanding and reading the information easy! The layout and design are simple and straight to

the point.

Our Arc Flash Warning Label includes the indication that an arc flash hazard is present, what corrective action to take, the risk hazard category, the incidentenergy, the arc flash boundary distance in inches, exactly what Personal Protection Equipment (PPE) that the worker must wear, the voltage that is present in the

enclosure, the limited approach boundary, the restricted approach boundary, the prohibited approach boundary, the class of Personal Protection Equipment(PPE) to wear for voltage protection along with the actual voltage protection requirement. For more about Arc Flash Warning Labels… Click Here…

Fill out the form above to receive the Full Version Download for FREE!

800-381-4389

ITU's Turn-Key Arc Flash Analysis (Arc Flash Risk Assessment) and Labeling Service includes:

No hidden charges, One Quote… That’s the price!

http://arcflashengineering.com/arc-flash-warning-labels



Our own employees do the work. No hired contractors.We label your required electrical panels. (Yes, we put the labels on for you.. turnkey!)

We provide you with a Complete Arc Flash Analysis Report and Updated Electrical One Line Drawings.Most common facilities completed in about a week.

Analysis conducted by experienced Electrical Engineers.Free Safety Training to educate your workers about your new safety program!

Why is ITU so successful? We make it easy for you… No Headaches, No Hassles, from start to finish. We make it easy!

We offer the most effective, NFPA. IEEE, and OSHA approved process to get your company in compliance with NFPA70e and OSHA cfr29-1910, AND wedo it at the lowest possible cost to you!

Give us a call Toll Free: 800-381-4389 or click the button to get a free quote!

FREE Safety Downloads

10 Steps of an Effective Arc Flash Analysis




Click to Download

PPE Category Level Chart Toolbox Poster

http://itudownloads.com/10-steps-to-an-arc-flash-safety-program.html

http://itudownloads.com/10-steps-to-an-arc-flash-safety-program.html



Click to Download

Arc Flash Approach Boundaries

http://itudownloads.com/ppe-category-chart.html

http://itudownloads.com/ppe-category-chart.html



Click to Download

Energized Electrical Work Permit

http://itudownloads.com/approach-boundaries.html

http://itudownloads.com/approach-boundaries.html



Click to Download

Arc Flash | Arc Flash Analysis, Studies and SurveysCopyright © 2015 All Rights Reserved

Arc Flash Engineering by ITUTerms and Conditions

http://itudownloads.com/energized-electrical-work-permit-eewp.html

http://itudownloads.com/energized-electrical-work-permit-eewp.html


http://www.goitu.com/

http://arcflashengineering.com/terms-and-conditions

Documents

Do-It-Yourself P3 Arc Flash Analysis Software _ Arc Flash Engineering