Embed Size (px)
Citation preview
Volume 2 • Issue 1 • 1000104J Chem Eng Process Technol ISSN: 2157-7048 JCEPT, an open access journal
Research Article Open Access
Priya et al. J Chem Eng Process Technol 2011, 2:1 DOI: 4172/2157-7048.1000104
Research Article Open Access
Degradation Studies of Tannery Effluents using Electro Flotation TechniqueP. Gomathi Priya*, V. Ramamurthi and Prabhu Anand
Department of Chemical Engineering, A.C. College of Technology, Anna University, Chennai- 600 025, India
Keywords: Electro flotation; Flocculent; Surfactant; Chemicaloxygen demand; Tannery effluent
IntroductionIndustrialization has its effect on environment by causing pollution,
among which water pollution is contributed by the industries, the nature of effluents from industries are varied and is industry specific. Especially the leather industry has been facing a major threat regarding the ecological problems caused by their waste streams [1]. In tanneries the conversion of the raw hide into leather necessitate different mechanical and chemical treatments e.g. soaking, liming, deliming, bathing, pickling, skin degreasing and tanning, etc. The low efficiency of the chemical operations generates large quantities of effluents like 30 -35 L kg-1 of raw materials processed [2]. The commonly used technology for effluent treatment was physicochemical followed by units of biological treatment, and activated sludge or aerated lagoon systems [3]. Generally these conventional treatments are unable to reduce all of the polluting parameters like COD, chlorides, sulphates and ammonia [4,5]. The tanning of hides and skins to convert them into leather has been an important activity.
The tannery effluent is a mixture of biogenic matter and large variety of organic and inorganic chemicals. These may contains high concentrations of chlorides, aliphatic sulphonates, sulfates, aromatic and aliphatic ethoxylates, sulfonated poly-phenols, acrylic acid condensates, fatty acids, dyes, proteins, soluble carbohydrates and Na2S. Conventional physio-chemical treatment of tannery effluents consists of pretreatment, coagulation/flocculation, sedimentation and sludge handling. In addition to chemical coagulation treatment, secondary and tertiary treatment methods such as biological filters, activated sludge etc. are being practiced. If nitrogen content is high, an additional step involving de nitrification is essential. The fats and proteins are partially hydrophobic they can be easily separated by floatation rather than sedimentation. Separation by flotation is relatively simple and faster compared to the other process. Hence removal of such pollutants by floatation could be more appropriate. Water treatments based on the electro flotation technique have been recently proved to circumvent most of these problems, while being also economically attractive [6-8,8-12]. In this work industrial effluent was carried out using electro floatation.
Electro flotation is a process of removing dispersed particles from liquid using gas bubbles. The gas bubbles are obtained through the
*Corresponding author: P. Gomathi Priya, Department of Chemical Engineering, A.C. College of Technology, Anna University, Chennai- 600 025, India, Tel: +91 44 22359138; E-mail: [email protected]
Received January 24, 2011; Accepted March 11, 2011; Published March 15, 2011
Citation: Priya PG, Ramamurthi V, Anand P (2011) Degradation Studies of Tannery Effluents using Electro Flotation Technique. J Chem Eng Process Technol 2:104. doi:10.4172/2157-7048.1000104
Copyright: © 2011 Priya PG, et al. This is an open-access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.
AbstractThis study reveals that the treatment of tannery effluent samples by electro flotation. In this system, the various
parameters like effect of pH, current density, COD, total solids, addition of surfactant and flocculent were investigated. It was found that maximum degradation was at the current density of 0.14A/cm2 and at a pH of 6.0. Under the same experimental conditions the removal efficiency of chemical oxygen demand (COD) and total solids were found to be approximately 66.3% and 80% respectively. The current density was the most significant factor in the suspended solids elimination by the addition of surfactant and flocculent concentration. The addition of surfactant increases the COD removal and it also enhances the total solids removal. The flocculent also enhanced electro flotation and this technique was found to be effective in removing total solids and reducing COD from tannery effluents. These results intend an important role of these parameters in electrochemical process for removing tannery effluents.
electrolysis of water, which produces hydrogen and oxygen gas. The electrodes are arranged at the bottom of a tank filled with the solution containing the dispersed solids. During the electro flotation process, current is passed through the electrodes and producing bubbles of hydrogen and oxygen gas. Where the bubbles float on the tank may colloid with particles suspended in the water. Adhere to them and float them to the surface of the water. Dispersed foam was skimmed off the surface of the tank with a bladed transport system or skimmer.
Overall process of electro flotation
The basic principle of such process lies on water electrolysis subsequently. It may be determined among other variables on pH and temperature. The electrochemical reactions at the cathode and the anode are hydrogen evolution and oxygen evolution respectively.
At Anode:
Fe(s) → Fe 2+ +2e (1)
Fe (aq) +2OH- (aq) Fe (OH) 2 (s) (2)
At Cathode:
2 H2O+2e- → H 2+2OH-(aq) (3)
Overall:
Fe(S) + 2H2O (l) →Fe (OH) 2(s) +H2 (g) (4)
The protonated water shows to be equivalent in both consumption and generation of positively charged species. Half reaction (first reaction) is proposed to be achieved in the anode while the second
Journal of Chemical Engineering & Process TechnologyJournal
of C
hem
ical E
ngineering & Process Technology
ISSN: 2157-7048
Page 2 of 4
Citation: Priya PG, Ramamurthi V, Anand P (2011) Degradation Studies of Tannery Effluents using Electro Flotation Technique. J Chem Eng Process Technol 2:104. doi:10.4172/2157-7048.1000104
Volume 2 • Issue 1 • 1000104J Chem Eng Process Technol ISSN: 2157-7048 JCEPT, an open access journal
at the cathode. From the literature [13] the author has performed a complete analysis about the experimental consequences of producing gas through electrolysis.
One of the gases (oxygen or hydrogen) is preferably used to perform the electro flotation, the aqueous speciation will change. The current density influences directly the number and size of bubbles [14]. If the current density is significantly low, both convective and diffusive mechanisms lead to gas to be dissolved and there may not even a bubble to occur. The latter will happen even at high current density which represents a waste of energy. Besides, this problem comes in addition to the inherent chemical irreversibility of both electrode reactions which set the voltage applied be significant. From the process point of view, during gas nucleation, other mechanisms start to work such as bubble coalescence. This mechanism makes bubbles to coarse and produce bubbles of larger size decreasing the bubbling surface available and inevitably an inefficient global process.
Materials and MethodsThe tannery effluents were collected from KAS leathers, Erode,
Tamil Nadu in India. These effluents were taken in a way to respect the standards of sampling and were stored in the cold storage before experimental works were started. The characterization of the effluent was carried out. The electrolytic cell is comprised of a sheet of mild steel as anode and a sheet of stainless steel as cathode each having the dimensions of 7.5cm X 4cm with the porosity of 0.5mm in both the electrodes. The Triton –X and the FeCl3 was added as surfactant and flocculent during the experiment. The electrodes were connected to a digital DC regulated power supply unit (0-30V, 0-12A). A peristaltic pump was used to take away the treated effluent at different time intervals.
The number of colony forming units can be found using equation (5)
No. of colony forming units (CFU) (Per ml of sample) = No. of colonies X Dilution factor of the plate counted. (5)
Experimental procedure
The electro flotation was carried out in an electrolytic cell having the capacity of one liter effluent solution. The distance between the electrodes maintained was 1.5cm. Before the experiment the electrodes were washed with diluted hydrochloric acid to remove surface grease, rust, oil and other impurities on the steel surfaces and then dried. The effluent was taken in the electrolytic cell and electro flotation was carried out at different time intervals. During the electro flotation reaction the effluents were taken out and analyzed for COD and Total Solids content. The various effects of the surfactant Triton –X (0.1ml/100ml) and the flocculent FeCl3 (0.5g/L) during the experiment were also discussed.
Results Effect of current density
To carry out the optimum current density to the removal percentage of COD of tannery waste water was represented in Figure 1. The experiments were conducted using the tannery waste water at pH of 6. During the experiment, the current densities ranging from 0.035A/Cm2, 0.07 A/Cm2, 0.105 A/Cm2 to 0.14 A/Cm2 were adjusted. The current density significantly affects the efficiency of electro flotation. It showed that the COD removal efficiency was increased with increasing the current density 63% to 65.9%. The rate of reduction of COD increases with different current densities but the increase is not linear then it may be concluded that the process is controlled by diffusion.
In electro flotation, COD reduction is associated with three factors,
1. Direct oxidation of organic residue on electrode
2. Removal of material particles by gas bubbles
3. Indirect oxidation through reactive species
During the electro flotation batch experiments, the magnitude of the current density had a significant effect on COD and the total solids removal. The total solids removal efficiency was increased with increasing the current passed through the electrodes. The removal rate of COD assumed to be obeying first order kinetics; hence the rate equation is given as [15]
( ) ( )d COD K CODdt
= − (6)
The rate constant was calculated for all the current density and using the above equation the K was calculated for each value of current density and at each time interval and averaged.
From the Figure 1 it was observed that the total solids removal was reached maximum at the same current density after 60 minutes of electro flotation. The raw effluent was subjected to electro flotation and was observed for bacterial colonies by standard plate count method. The major part of the procedure deals with a series of successive dilutions of the tannery waste water in sterile bottle with sterile water. The diluted waste water samples of before and after electro flotation was taken. Then it was poured into Petri dishes containing nutrient agar. The numbers of colonies were counted after incubation for 48 hours at 37oC. The disinfection involves two mechanisms like due to oxidation and precipitation with Fe (OH)3.
The chlorides ions present in the effluent also contribute disinfection. i.e. in electro flotation the anodic oxidation causes chloride ions to form hypo chlorites ions which could be used as disinfectant.
It was observed at the crude sample after series of dilution had contained 7200000 (approximately) that is 72 prominent colonies. Bacteria of mixed culture per ml. after subjecting to electro flotation for various time intervals from 5-60 minutes at 0.14A/Cm2 of current density the colonies were found to be eliminated to the extent of 86.6% shown in the Figure 1.
Effect of pH
It has been found that the influence of pH is an important parameter for the performance of the electrochemical process [16,17]. In the electro flotation process the pH of the solution is known to play an important role in the removal efficiency of pollutants. To examine the pH on the tannery effluent was adjusted to the desired pH with diluted sodium hydroxide or hydrochloric acid. The experiments were conducted for pH ranges from 3 to 10 by keeping the current density constant at 0.035A/Cm2 for the same electro flotation time of 60 minutes. The experiment results shows in Figure 2, and it was observed that the total solids removal efficiency and COD decreased for pH below 4 and above 9, this is due to an extent of the reduction of Fe3+ is favored. At the pH range of 5-9, hydrolysis and reduction takes place and it forms mononuclear or poly nuclear ferrous complexes as Fe (OH)
3, Fe (OH) 2+. Which are effective pollutants but at high pH solutions
that dominant species was Fe (OH) 4– which does not coagulate with the
pollutants [18]. From this result it may be concluded that the pH of the experiment was further followed at 6.
Effect of surfactant
Total solids were removed using electro flotation and the process
Page 3 of 4
Citation: Priya PG, Ramamurthi V, Anand P (2011) Degradation Studies of Tannery Effluents using Electro Flotation Technique. J Chem Eng Process Technol 2:104. doi:10.4172/2157-7048.1000104
Volume 2 • Issue 1 • 1000104J Chem Eng Process Technol ISSN: 2157-7048 JCEPT, an open access journal
was further enhanced by adding the surfactant Triton –X. In the Figure 3, it was observed that the addition of surfactants enhances the total solids removal. In the process of electro flotation alone the removal percentage was found to be 66% but when this process was improved with surfactant and the removal percentage of total solids has been reached to 78%. From the same Figure, it may be concluded that, an addition of surfactant initially increases the COD value due to the release of a new organic compound in the waste water. During electro flotation, these surfactants also gets removed along with the low density colloidal particles by formation of surfactant – particulate - bubble composite and reduction of COD removal percentage is slightly decreased when surfactant is used in normal electro flotation process the removal percentage was 71% when surfactants are added the value
of percentage removal has been increased to 80%.
Effect of flocculating agent
The well known flocculating agent known as FeCl3 was added to the waste water and its effect in removal of total solids and COD has been studied. FeCl3 was used in most of the tannery waste water treatment due to its efficiency and low cost [19]. The flocculating agents are polymers of high molecular weight; they have property to be adsorbed with solid –liquid or liquid –liquid interface which allows the aggregation of the colloidal particles by formation of bridges between the dispersed particles. The metal ions present in the coagulant causes coagulation of the colloidal organic matter and the suspended solids resulting in the formation of rather larger particles (flocs) which are attached to the surface of the gas bubbles and are collected at the top of the electro flotation bath [20].
The removal efficiency of Total Solids has been increased up to 80% within 60 minutes of electro flotation at the current density of 0.14A/Cm2. The COD removal percentage has also been increased up to 64% with the addition of FeCl3 this is explained by the oxidation of dissolved organic substance due to the presence of both fine oxygen bubbles and the chlorine as a strong oxidizing agent in the medium. The Chlorine was the oxidation product in the secondary electrochemical anodic reaction during electrolysis [21]. From the Figure 4, it was found that Total Solids removal efficiency and COD removal efficiency increased with the addition of flocculent to the electro flotation unit.
DiscussionTannery effluent samples were treated by electro flotation technique
0102030405060708090
100
0 10 20 30 40 50 60 70 80Time (min)
Rem
oval
(%)
COD Total Solids Bacteria
Figure 1: Effect of current density as a function of electrolysis time on COD, Total solids and Bacteria removal percentage.
0
10
20
30
40
50
60
70
0 10 20 30 40 50 60 70 80Time (min)
COD
rem
oval
(%
)
0.035A/cm2
0.07 A/cm2
0.105A/cm2
0.14 A/cm2
Figure 5: Effect of current density on COD removal.
0
10
20
30
40
50
60
70
80
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14
pH
Rem
oval
(%)
COD Total Solids
Figure 2: Effect of pH on COD and Total solids removal.
Figure 3: Effect of surfactant and Flocculants as a function of electrolysis time on Total solids removal.
0
10
20
30
40
50
60
70
80
90
0 5 10 15 20 30 40 50 60Time (min)
Tota
l sol
ids
rem
oval
(%)
With surfactant With floculant Without surfactant Without floculant
Figure 4: Effect of Flocculants and surfactant as a function of electrolysis time on COD.
0
10
20
30
40
50
60
70
80
0 10 20 30 40 50 60Time(min)
CO
D re
mov
al (%
)
With surfactant Without surfactant With floculant Without floculant
Page 4 of 4
Citation: Priya PG, Ramamurthi V, Anand P (2011) Degradation Studies of Tannery Effluents using Electro Flotation Technique. J Chem Eng Process Technol 2:104. doi:10.4172/2157-7048.1000104
Volume 2 • Issue 1 • 1000104J Chem Eng Process Technol ISSN: 2157-7048 JCEPT, an open access journal
and found to be effective for the removal of total solids and COD using mild steel as anode and stainless steel sheet as cathode. During the process the increase in removal of total solids and COD was found to be increasing with the different applied current densities. The addition of surfactant increases the COD removal as well as it increases the total solids removal from 66.3% to78%. The flocculants FeCl3 enhanced electro flotation was found to be more effective in removing Total solids and COD from tannery effluent. After the electro flotation process COD removal was reached to about 66% and pathogenic bacteria could be eliminated to the extent of 86.6%References
1. Swaminathan G, Muralidharan C, Rangasamy T, John Sundar V, Sivakumar V (2005) Management of total dissolved solids in tanning process through improved techniques. Journal of Cleaner Production 13: 699-703.
2. Rajamani S, Ravindranath E, Chita T, Umamaheswari B, Ramesh T, et al. (2004) Membrane application for recovery and reuse of water from treated tannery wastewater. Desalination 164: 151-156.
3. Moura Alencar MCP, Castro Dantas TN, Dantas Neto AA (2004) Evaluation and optimization of chromium removal from tannery effluent by micro emulsion in the Morris extractor. J Hazard Mater 114: 115-122.
4. Molinari R, Drioli E, Cassano A (1997) Recovery and reuse of chemical in unhearing, degreasing and chromium tanning processes by membranes. Desalination 113: 251-261.
5. Molinari R, Drioli E, Cassano A, Romano M (2001) Treatment of aqueous effluents of the leather industry by membrane processes. J Memb Sci 181: 111-126.
6. Alinsafi A, Khemis M, Pons MN, Leclerc JP, Yaacoubi A, et al. (2005) Electro coagulation of reactive textile dyes and textile waste water. Chem Eng Process 44: 461-470.
7. Daneshvar N, Oladegaragoze A, Djafarzadeh N (2006) The use of artificial neural networks (ANN) for modeling of decolorization of textile dye solution containing C. I. Basic Yellow 28 by electro coagulation process. J Hazard Mater 129: 116-122.
8. Bayramoglu M, Eyvaz M, Kobya M (2007) Treatment of the textile wastewater by electro coagulation Economical evaluation. Chemical Engineering Journal 128: 155-161.
9. Kobya M, Can OT, Bayramoglu M (2003) Treatment of textile wastewaters by electro coagulation using iron and aluminum electrodes. J Hazard Mater 100: 163-178.
10. Bayramoglu M, Kobya M, Can OT, Sozbir M (2004) Operating cost analysis of electro coagulation of textile dye wastewater, Separation and Purification Technology 37: 117-125.
11. Can OT, Kobya M, Demirbas E, Bayramoglu M (2006) Treatment of the textile wastewater by combined electro coagulation. Chemosphere 62: 181-187.
12. Kobya M, Demirbas E, Can OT, Bayramoglu M (2006) Treatment of levafix orange textile dye solution by electro coagulation. J Hazard Mater 132: 183-188.
13. Ketkar DR, Mallikajunan R, Venkatachalam S (1991) Electro flotation of quartz fins. International journal of miner Proc 31: 127-138.
14. Fukui Y, Yuu S (1985) Removal of colloidal particles in electro flotation. AIChE J 31: 201-208.
15. Laviron, Maja (1972) Influence of the adsorption of the depolarizer or of a product of the electrochemical reaction or polarographic current: XVII theoretical study of a reversible surface reaction followed by a first order chemical reaction in linear potential sweep voltammetry. J Electro anal Chem 35: 333-342.
16. Lin SH, Chen ML (1997) Treatment characteristics of textile wastewater and removal of heavy metals using the electro flotation technique. Water Res 31: 868-876.
17. Chen X, Chen G, Yue PL (2000) Separation of pollutants from restaurant wastewater by electro coagulation. Sep Purif Technol 19: 65-76.
18. Chig-Ta –Wang (2009) Removal of COD from laundry wastewater by electro coagulation/ electro flotation. J Hazard Mater 164: 81-86.
19. Aboulhassan MA, Souabi S, Yaacoubi A (2007) Pollution reduction and biodegradability index improvement of tannery effluents. Int J Environ Sci Tech 5: 11-16.
20. Jiantuan Ge, Jiuhui Qu (2004) New bipolar electro coagulation-electro flotation process for the treatment of laundry wastewater. Separation and Purification Technology 36: 33-39.
21. Ben mansour L (2007) Treatment of wastewaters of paper industry by coagulation –electro flotation. Desalination 208: 34-41.
