CMU200 User Manual R&S English

Edited by Foxit Reader Copyright(C) by Foxit Software Company,2005-2008 For Evaluation Only.

Test and Measurement Division

Operating Manual

Software Options:

GSM400/850/900/1800/1900-MS for CMU-B21B(Board) :hardware card

R&S CMU-K20/-K21/-K22/-K23/-K24K(Kit) software kit1115.5900.02/6007.02/6107.02/6207.02/6307.02 Including the following extensions:

GPRS/EGPRS Software Extensionfor all GSM Software Packages

R&S CMU-K42/-K431115.4691.02/1115.6907.02

AMR GSM for CMU 200R&S CMU-K451150.3100.02

Printed in the Federal Republic of Germany

1115.6088.12-13-

1

Dear Customer,throughout this manual, CMU-K20 to CMU-K24 and CMU-K42/-43/-K45 is generally used as an abbreviation for software options R&S CMU-K20 to R&S CMU-K24 and R&S CMU-K42/-K43/-K45. The Universal Radio Communication Tester R&S CMU 200 is abbreviated as CMU200.


CMU-K20/-K21/-K22/-K23/-K24

Contents

Tabbed Divider Overview

Safety Instructions Certificate of Quality List of R&S Representatives Contents of Manuals for Universal Radio Communication Tester CMU

Tabbed Divider

1 2 3 4 5 6 7 10

Chapter 1: Chapter 2: Chapter 3: Chapter 4: Chapter 5: Chapter 6: Chapter 7: Index

Installation Getting Started Manual Operation Functions and their Application Remote Control Basics Remote Control Commands Remote Control Program Examples

1115.6088.12

RE

E-3

CMU-K20/-K21/-K22/-K23/-K24

List of Figures

List of FiguresFig. 4-1 Fig. 4-2 Fig. 4-3 Fig. 4-4 Fig. 4-5 Fig. 4-6 Fig. 4-7 Fig. 4-8 Fig. 4-9 Fig. 4-10 Fig. 4-11 Fig. 4-12 Fig. 4-13 Fig. 4-14 Fig. 4-15 Fig. 4-16 Fig. 4-17 Fig. 4-18 Fig. 4-19 Fig. 4-20 Fig. 4-21 Fig. 4-22 Fig. 4-23 Fig. 4-24 Fig. 4-25 Fig. 4-26 Fig. 4-27 Fig. 4-28 Fig. 4-29 Fig. 4-30 Fig. 4-31 Fig. 4-32 Fig. 4-33 Fig. 4-34 Fig. 4-35 Fig. 4-36 Fig. 4-37 Fig. 4-38 Fig. 4-39 Fig. 4-40 Fig. 4-41 Fig. 4-42 Fig. 4-42 Fig. 4-43 Fig. 4-44 Fig. 4-45 Fig. 4-46 Measurement menu Analyzer/Generator (example: P/t Norm. GMSK) .................................4.3 Measurement menu Power P/t Norm. GMSK .....................................................................4.9 Trigger slot offset and slot count (for Trig. Slot Offset = 3) ..................................................4.18 Display of results (Power P/t Norm. GMSK)......................................................................4.20 Display of results (Power P/t Norm. 8PSK) .......................................................................4.22 Display of results (Power P/t Multislot) ..............................................................................4.23 Display of results (Power P/Frame)...................................................................................4.25 Display of results (Power P/Slot menu).............................................................................4.26 Display of results (Power P/Slot Table) .............................................................................4.27 Power Configuration Control .............................................................................................4.28 GSM power/time template for normal and access bursts with GMSK modulation...............4.33 GSM power/time template for normal bursts with 8PSK modulation ...................................4.34 GSM power/time template for multislot configurations.........................................................4.34 Power Configuration Limit Lines........................................................................................4.35 Measurement menu Modulation Ext. Phase Err. GMSK...................................................4.39 Display of results (Modulation Ext. Phase Err. GMSK) .....................................................4.41 Modulation errors in the I/Q vector diagram .........................................................................4.44 Modulation errors in the I/Q constellation diagram...............................................................4.44 Measurement menu Modulation Overview 8PSK..............................................................4.45 Display of results (Modulation Overview) ..........................................................................4.47 Display of results (Modulation EVM / Phase Error / Magn. Error) .....................................4.48 Modulation Configuration Control......................................................................................4.51 Modulation Configuration Limits ........................................................................................4.52 Spectrum due to modulation and switching transients in time domain representation ........4.55 Measurement menu Spectrum due to Modulation ...............................................................4.56 Display of results (spectrum due to modulation) ..................................................................4.58 Display of results (spectrum due to switching) .....................................................................4.60 Spectrum Configuration Control ........................................................................................4.62 Spectral mask as specified for GSM mobile stations...........................................................4.65 Spectrum Configuration Limit Lines ..................................................................................4.66 Spectrum Configuration Limits ..........................................................................................4.68 Spectrum Configuration Meas X .......................................................................................4.69 Connection Control Analyzer (softkey) ..............................................................................4.72 Bit structure of a GSM normal burst.....................................................................................4.74 Connection Control Analyzer (table)..................................................................................4.76 Connection Control Generator (softkey)............................................................................4.79 Connection Control Generator (table) ...............................................................................4.83 Connection Control AF/RF connectors..............................................................................4.84 Connection Control Synchronization .................................................................................4.86 Connection Control Trigger ...............................................................................................4.89 Connection Control I/Q-IF .................................................................................................4.91 Signalling states of the CMU (circuit switched mode) ..........................................................4.94 Connection Control Connection (Signal Off) .....................................................................4.95 Connection Control Connection (Signal On) .....................................................................4.97 Overview of settings and measurements .............................................................................4.99 Measurement menu Power P/t Normal GMSK ...............................................................4.102 Display of measurement results (P/t Normal GMSK menu)...............................................4.109

1115.6088.12

3

E-13

List of FiguresFig. 4-47 Fig. 4-48 Fig. 4-49 Fig. 4-50 Fig. 4-51 Fig. 4-52 Fig. 4-53 Fig. 4-54 Fig. 4-55 Fig. 4-56 Fig. 4-57 Fig. 4-58 Fig. 4-59 Fig. 4-60 Fig. 4-61 Fig. 4-62 Fig. 4-63 Fig. 4-64 Fig. 4-65 Fig. 4-66 Fig. 4-67 Fig. 4-68 Fig. 4-69 Fig. 4-70 Fig. 4-71 Fig. 4-72 Fig. 4-73 Fig. 4-74 Fig. 4-75 Fig. 4-76 Fig. 4-77 Fig. 4-78 Fig. 4-79 Fig. 4-80 Fig. 4-81 Fig. 4-82 Fig. 4-83 Fig. 4-84 Fig. 4-85 Fig. 4-86 Fig. 4-87 Fig. 4-88 Fig. 4-89 Fig. 4-90 Fig. 4-91 Fig. 6-1 Fig. 6-2

CMU-K20/-K21/-K22/-K23/-K24

Display of results (Power P/t Norm. 8PSK) .....................................................................4.111 Display of results (Power P/t Multislot) ............................................................................4.112 Display of measurement results (P/PCL menu) .................................................................4.112 Display of measurement results (P/t Access Burst menu).................................................4.113 Power Configuration Limits .............................................................................................4.117 Measurement menu Modulation.........................................................................................4.118 Display of results (modulation menu) .................................................................................4.119 Measurement menu Spectrum (application Modulation)....................................................4.120 Signal paths for BER measurements .................................................................................4.124 52-multiframe for PDCH.....................................................................................................4.126 Comparison between BLER and DBLER: CS4 (left diagram) and CS1.............................4.127 Single-limit confidence BER ...............................................................................................4.131 Dual-limit confidence BER..................................................................................................4.132 Receiver Quality (BER) ......................................................................................................4.133 Display of test settings and measurement results (BER)...................................................4.136 Display of test settings and measurement results (BLER).................................................4.139 Receiver Quality Control..................................................................................................4.145 Receiver Quality Configuration Limits .............................................................................4.150 Connection Control Connection (Synchronized) .............................................................4.153 Connection Control Connection (Alerting).......................................................................4.154 Connection Control Connection (Call Established) .........................................................4.155 Connection Control Handover (destination selection) .....................................................4.159 Connection Control Handover (Call Pending) .................................................................4.160 Connection Control MS Signal (panel, single slot) ..........................................................4.162 Connection Control MS Signal (panel, multislot).............................................................4.164 Connection Control MS Signal (table) .............................................................................4.167 Connection Control BS Signal (panel, single slot)...........................................................4.169 Connection Control BS Signal (panel, multislot) .............................................................4.172 Connection Control BS Signal (table)..............................................................................4.174 Connection Control Network parameters (panel)............................................................4.177 Connection Control Network parameters (table).............................................................4.180 Connection Control AF/RF connectors............................................................................4.187 Connection Control Trigger .............................................................................................4.188 Connection Control Input level ........................................................................................4.191 Meas. slot and slot count (for Meas. Slot = 3)....................................................................4.192 Connection Control Misc. ................................................................................................4.193 GPRS signalling states.......................................................................................................4.197 Connection Control Connection (Signal Off) ...................................................................4.199 Connection Control Connection (Idle) .............................................................................4.203 Connection Control Connection (Attached).....................................................................4.204 Connection Control Connection (TBF Established).........................................................4.205 Connection Control MS Signal (table) .............................................................................4.206 Connection Control BS Signal (table)..............................................................................4.207 Connection Control Network ...........................................................................................4.209 Connection Control Network parameters (AMR).............................................................4.214 Signalling states of the CMU and transitions including handover ......................................6.191 GPRS signalling states of the CMU and transitions ...........................................................6.229

1115.6088.12

4

E-13

CMU-K20/-K21/-K22/-K23/-K24

List of Tables

List of TablesTable 3-1 Table 4-1 Table 4-2 Table 4-3 Table 4-4 Table 4-5 Table 4-6 Table 4-7 Table 4-8 Table 4-9 Table 4-10 Table 4-11 Table 4-12 Table 4-13 Table 4-8 Table 4-9 Table 4-10 Table 4-11 Table 4-12 Table 4-13: Table 4-14: Table 4-15 Table 5-1 Table 5-2 Table 5-3 Table 5-4 Table 5-5 Table 6-1 Table 6-2 Table 6-3 Table 6-4 Measurement groups in Signalling and Non Signalling mode .........................................3.4 GSM tolerances for spectrum due to modulation ...........................................................4.64 GSM tolerances for spectrum due to modulation (absolute) ..........................................4.65 GSM tolerances for spectrum due to switching plus modulation effects:.......................4.67 GSM channels in uplink direction ...................................................................................4.73 GSM channels in downlink direction...............................................................................4.80 I/Q-IF scenarios and path settings..................................................................................4.92 GSM Power classes .....................................................................................................4.116 GSM Power control levels (PCL) ..................................................................................4.116 BLER and DBLER measurement settings....................................................................4.125 Frame structure for Main Service: Circuit Switched .....................................................4.127 Frame structure for Main Service: Packet Data, Service Selection: Red. Sig. EGPRS sym................................................................................................4.128 Frame structure for Main Service: Packet Data, Service Selection: Red. Sig. EGPRS asym..............................................................................................4.128 Frame structure for Main Service: Packet Data, any other Service Selection..............4.128 Definition of RX Level ...................................................................................................4.141 Definition of RX Quality.................................................................................................4.142 Definition of Sign. Var. ..................................................................................................4.143 Definition of Mean BEP.................................................................................................4.143 Definition of CV BEP.....................................................................................................4.144 MS multislot classes .....................................................................................................4.156 MS multislot classes .....................................................................................................4.201 AMR Rate Set according to the conformance test specification ..................................4.213 Measurement objects in Signalling and Non Signalling mode..........................................5.3 Repetition mode in remote control....................................................................................5.5 Limits and limit check .......................................................................................................5.6 Meaning of the bits used in the STATus:OPERation:CMU:SUM1|2:CMU sub-registers assigned to GSMxxx-MS Non Signalling ....................................................5.7 Meaning of the bits used in the STATus:OPERation:CMU:SUM1|2:CMU sub-registers assigned to GSMxxx-MS Signalling............................................................5.7 Remote control commands: Non Signalling .................................................................6.244 Remote control commands: Signalling mode...............................................................6.263 Remote control commands: Non Signalling mode .......................................................6.291 Remote control commands: Signalling mode...............................................................6.304

1115.6088.12

5

E-13


CMU-K20/-K21/-K22/-K23/-K24

Manuals

Contents of Manuals for Universal Radio Communication Tester CMUThe user documentation for the R&S CMU 200/300 is divided in an operating manual for the basic instrument (including options CMU-B41, CMU-B17) and separate manuals for individual software and hardware options. The complete documentation is available on CD-ROM, stock no. PD 0757.7746.2x. The latest revisions of all manuals are also posted on the CMU Customer Web on GLORIS.

Operating Manual CMU-K20/-K21/-K22/-K23/-K24 Setting up OptionSoftware Kit (Software Options: GSM400/900/1800/1900/850-MS for CMU-B21)The present operating manual describes the application of CMU for GSM mobile tests including the GPRS/EGPRS and AMR software extensions. It gives comprehensive information about the installation of the required software options and about manual and remote control of the instrument. Typical measurement tasks are explained in detail using the functions offered by the graphical user interface and a selection of program examples. The manual is organized as follows: Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 5 Chapter 6 Describes the steps necessary for installing the software and putting the instrument into operation. Gives an introduction to the application of the CMU for GSM mobile station tests and presents typical measurement examples. Gives an overview of the user interface and describes the concepts of measurement control and instrument configuration. Represents the reference chapter providing detailed information on all functions of the user interface and their application. Describes the basics of remote control of the instrument for GSM base station tests. Lists all remote control commands for GSM mobile station tests. At the end of the chapter the commands are grouped together according to their function (measurement groups or configurations) and sorted in alphabetical order. Contains program examples. Contains an index for the operating manual.

Chapter 7 Chapter 10

Operating Manual CMU200/CMU300In the operating manual for CMU basic unit you will find everything that is needed to make yourself familiar with your Universal Radio Communication Tester CMU. This includes information about the technical specifications of the CMU, the controls and connectors on the front and rear panel, necessary steps for putting the instrument into operation, the basic operating concept, manual and remote control. Typical measurement tasks are explained in detail using the functions of the user interface and program examples. In addition, the operating manual lists the most important warnings and error messages which may be output by the instrument. General concepts of CMU control are described in the operating manual CMU and not repeated in the manuals for the individual software options.

1115.6088.12

0.1

E-13


Manuals Service Manual Instrument

CMU-K20/-K21/-K22/-K23/-K24

The service manual instrument informs on how to check compliance with rated specifications, on instrument function, repair, troubleshooting and fault elimination. It contains all information required for the maintenance of CMU by exchanging modules.

Service Manual ModulesThe service manual modules is not delivered with the instrument but may be obtained from your R&S service department using the order number 1100.4903.91. Service manual modules contains information about the individual modules of CMU. This comprises the test and adjustment of the modules, fault detection within the modules and the interface description.

Further Operating Manuals for Network TestsThe operating manuals listed in the following table describe the test of mobile phones supporting different standards by means of the CMU and the appropriate software and hardware options. The network test operating manuals are organized like the present GSM-MS operating manual.For Options Manual Operating Manual CMU-K27/-K28 Operating Manual CMU-K29 Operating Manual CMU-K30/-K31/K32/-K33/-K34 Order Number 1115.6688.12 1115.6888.12 1115.4185.12 Type CMU-K27 CMU-K28 CMU-K29 CMU-K30 CMU-K31 CMU-K32 CMU-K33 CMU-K34 CMU-K39 CMU-K41 Operating Manual CMU-K53 Operating Manual CMU-K65/-K66 Operating Manual CMU-K75/-K76 Operating Manual CMU-K81/-K82 Operating Manual CMU-K83/-K84/ -K85/-K87 Operating Manual CMU-K88 1115.5081.12 1115.4962.12 1150.3398.12 CMU-K53 CMU-K65 CMU-K66 CMU-K75 CMU-K76 CMU-K81 CMU-K82 CMU-K83 CMU-K84 CMU-K85 CMU-K86 CMU-K88 Description TDMA800-MS for CMU-B21 TDMA1900-MS for CMU-B21 AMPS-MS for CMU-B21 GSM400-BS for CMU-B21 GSM900-BS for CMU-B21 GSM1800-BS for CMU-B21 GSM1900-BS for CMU-B21 GSM850-BS for CMU-B21 MOC/MTC EDGE for CMU-K30/31/32/33 Bluetooth for CMU WCDMA UE TX Test (3GPP/FDD) WCDMA (3GPP/FDD, DL) Generator WCDMA Node B TX Tests WCDMA Generator (3GPP/FDD, Release 99, Uplink) CDMA800-MS (IS95) for CMU-B81 CDMA1900-MS (IS95) for CMU-B81 CDMA2000-MS (450 MHz band) CDMA2000-MS (cellular band) CDMA2000-MS (PCS band) CDMA2000-MS (IMT-2000 band) 1xEV-DO for CMU-B88 Stock No. 1115.6607.02 1115.6707.02 1115.6807.02 1115.4004.02 1115.4104.02 1115.4204.02 1115.4304.02 1115.4404.02 1115.4791.02 1115.4604.02 1115.5000.02 1115.4962.12 1115.5100.02 1150.3200.02 1150.3300.02 1115.5500.02 1115.5600.02 1150.3500.02 1150.3600.02 1150.3700.02 1150.3800.02 1150.3998.12

1115.5581.12 1150.0382.12

1150.3900.02

The GSM base station tests described in operating manual CMU-K30/-K31/-K32/-K33/-K34 and the WCDMA Node B tests described in operating manual CMU-K75/-K76 require a CMU300 (Universal Radio Communication Tester for BTS). Bluetooth tests can be performed with model CMU200, var. 02 or 53. All other radio communication equipment is tested with model CMU200, var.02.

1115.6088.12

0.2

E-13

CMU-K20/-K21/-K22/-K23/-K24

Manuals

What's new in this Revision...This operating manual describes version V3.50 of the GSM-MS firmware package. Compared to previous versions, this new firmware provides numerous extensions and improvements. The new features described in this manual are listed below.New Features Non Signalling: Aux TX Description The additional RF generator (option R&S CMU-B95) is available in Non Signalling mode. Refer to... Chapter 4, GSM Module Tests (Non Signalling) Generator Settings Chapter 4, GSM Module Tests (Non Signalling) Spectrum Measurements Chapter 4, GSM Mobile Tests (Signalling) Receiver Quality Measurements

Spectrum

Improved Spectrum measurement in Non Signalling and Signalling mode: Time domain measurement at off-carrier frequencies, auto-detection of modulation scheme. Extended Receiver Quality measurement: New results (long term throughput, false USF detection), configurable downlink resources, receiver reports for GPRS and EGPRS. Automatic activation of DL and UL slots in multislot packet data mode according to the multislot class of the MS and the needs of the measurement. Inter-cell handover from WCDMA to GSM supported.

BER/BLER

Auto Slot Config.

Chapter 4, GSM Mobile Tests (Signalling) Connection Control See operating manual for WCDMA UE test option (R&S CMU-K65//69), Chapter 4 Handover Chapter 4, GSM Mobile Tests (Signalling) Handover Network Parameters

WCDMA to GSM handover

WCDMA to GSM handover

GSM prepare session with GSM-specific RF signal and network settings. New parameters: Alerting, Cell Synchronization. The WCDMA neighbor cell description is sent to the mobile in order to prepare the handover. New Service Selections: Test mode A and B for EGPRS channels, symmetric and asymmetric EGPRS loopback mode An ACTIVATE PDP CONTEXT REQUEST message from the mobile can be either accepted or rejected

EGPRS extensions

Chapter 4, GSM Mobile Tests (Signalling) GPRS Signalling and EGPRS Chapter 4, GSM Mobile Tests (Signalling) GPRS Signalling and EGPRS Chapter 2, Application example on Multislot Measurements with mixed modulation schemes

PDP Context Activation

Power Mulislot

Simultaneous measurement and display of GMSK and 8PSK modulated burst in P/t Multislot.

1115.6088.12

0.3

E-13

Manuals Frequently Used AbbreviationsAB Abs. ACK AGC AMR AOC Atten. Aux TX BA Bandw. BCC BCCH BCCH BER BLER BS BS BS-AG-BLKS-RES BS-PA-MFRMS BTS Chan. CRC DBLER Disp. Err. EVM Ext. Ext. FAC FACCH FER Freq. GPRS GSM IF IMEI IMSI Lev. Magn. Max. Max./Min. MCC MNC MOC MS MSIN MTC NB Ovw. PCL PDTCH PDU PRBS PSR PTP RACH RBER Rcv. Ref. Rel. RF RMS SDCCH Seq. SMS SNR SVN TAC TBF

CMU-K20/-K21/-K22/-K23/-K24

Access Burst Absolute Acknowledged mode Automatic Gain Control Adaptive Multi-Rate (codec) Advice of Charge Attenuation Additional RF generator (signal) BCCH Allocation Bandwidth Base Transceiver Station Color Code Broadcast Control Channel Broadcast Control Channel Bit Error Rate Block Error Ratio Base (Transceiver) Station Base (Transceiver) Station Basic Services Access Grant Blocks Reserved Basic Service Paging Blocks Available per Multiframes Base Transceiver Station Channel Cyclic Redundancy Check Data Block Error Rate Display (Mode) Error Error Vector Magnitude Extended (phase error measurement) External Final Assembly Code Fast Associated Control Channel Frame Erasure Rate Frequency General Packet Radio Service Global System for Mobile Communication, Groupe Spcial Mobile Intermediate Frequency International Mobile Equipment Identity International Mobile Subscriber Identity Level Magnitude Maximum (e.g. Level) Maximum/Minimum Mobile Country Code Mobile Network Code Mobile Originated Call Mobile Station Mobile Subscriber Identity Number Mobile Terminated Call Normal Burst Overview Power Control Level Packet switched Data Traffic Channel Protocol Data Unit Pseudo Random Bit Sequence Pseudo Random Point to Point (GPRS services) Random Access Channel Residual Bit Error Rate Receiver Reference (marker) Relative Radio Frequency Root Mean Square (averaging) Stand-alone Dedicated Channel Sequence Short Message Service Serial Number Software Version Number Type Approval Code Temporary Block Flow

1115.6088.12

0.4

E-13

CMU-K20/-K21/-K22/-K23/-K24TDMA TLLI Trg. TSC USF Vect. Time Division Multiple Access Temporary Link Level Identity Trigger Training Sequence (Code) Update State Flag Vector

Manuals

1115.6088.12

0.5

E-13

CMU-K20/-K21/-K22/-K23/-K24

Contents of Chapter 1

Contents1 Installation and First Steps.................................................................................. 1.1Software Installation or Update...................................................................................................... 1.1 Creating a new Software Configuration ........................................................................................ 1.4 Enabling Software Options............................................................................................................. 1.6

1115.6088.12

I-1.1

E-6


CMU-K20/-K21/-K22/-K23/-K24

Software Installation or Update

1 Installation and First StepsThis chapter describes how to install, update or enable software options GSM400/850/900/1800/1900MS for the Universal Radio Communication Tester CMU200. Before proceeding to perform any of the steps described in this manual, please make sure that the instrument is properly connected and put into operation according to the instructions given in chapter 1 of the CMU200 manual. The hardware and software options available are shown in the Startup menu. The status of the software options required for GSM mobile tests is indicated in the lines CMU-K20 GSM400MS, CMU-K21 GSM900-MS, CMU-K22 GSM1800-MS, CMU-K23 GSM1900-MS, CMU-K24 GSM850MS, and CMU-K42 GPRS for GSM MS: If a version number is indicated, the CMU is ready to perform GSM mobile tests. In this case you may skip this chapter, except if you wish to update the current software version or activate another version. If disabled is indicated, the software option must be enabled using a key code; see section Creating a new Software Configuration on page 1.4. If not installed is indicated, the software must be installed via the PCMCIA interface or the floppy disk drive, see below.

Software Installation or UpdateThe CMU is always delivered with the latest software version available. New CMU software versions are available for download on the R&S Lotus Notes Service board. To be loaded via the PCMCIA interface, the software must be copied to one or several flash disks/memory cards or PCMCIA hard disks. An appropriate memory card CMU-Z1, order no. 1100.7490.02, can be obtained from Rohde & Schwarz. Note: If your CMU is equipped with a floppy disk drive (option CMU-U61), a set of installation floppy disks must be generated instead of a flash disk. All other steps do not depend on the storage medium.

The five software options GSM400/850/900/1800/1900-MS and the supplementary option GPRS for GSM MS (CMU-K42) are part of a single software package termed GSM MS, so they must be installed or updated together. They can be enabled and operated separately, see section Enabling Software Options on page 1.6. To install the GSM MS software proceed as follows: Switch off the CMU. Insert the flash disk into one of the two slots of the PCMCIA interface. Switch on the CMU. The installation is started automatically while the CMU performs its start-up procedure. To this end the VersionManager is called up (for a detailed description of the VersionManager refer to chapter 1 of the CMU operating manual or to the on-line help accessible via Info):

1115.6088.12

1.1

E-6


CMU-K20/-K21/-K22/-K23/-K24

Softkey no. 5 on the left softkey bar, Install software..., is used to install new software from an external storage medium. The CMU automatically recognizes the storage medium and indicates the corresponding slot number: Slot 0 or 1 denotes the left or right slot of the PCMCIA interface. If a floppy disk is used the menu option reads Install software version from floppy. Press left softkey no. 5 (Install software...) to start the installation. If your storage medium contains several installation versions, the software version selection dialog is opened:

Use the rotary knob or the cursor keys to scroll the list and select the GSM MS version you intend to install. Press Install to start the installation. The installation is started. To be operable on your instrument, a network option must be combined with a compatible version of the CMU base software. Any base software version installed on the CMU hard disk can be combined with one or several network options to form an independent software configuration. If none of the configurations is compatible to the new GSM MS option, the VersionManager displays an error message and takes you back to the software selection dialog; see section Creating a new Software Configuration on page 1.4. Otherwise, the following upgrade selection dialog is opened:

1115.6088.12

1.2

E-6

CMU-K20/-K21/-K22/-K23/-K24


The upgrade selection dialog displays a list of base software versions that can be combined with the new GSM MS software. Select the appropriate base version and press Upgrade. The new GSM MS option is added to the configuration or updates the previous GSM MS version of the configuration. To indicate that the storage medium must be changed the CMU issues the Change volume message:

Change volume

Process next volume ExitReplace the current disk with the disk requested. Use the cursor up/down keys to select Process next volume (default setting). Press ENTER to confirm that the new disk has been inserted and to continue the installation. After processing the last disk the CMU displays the following screen:

If you wish to install or upgrade other software versions, press left softkey no 4 or 5 (Install next software...) or insert new storage medium into the PCMCIA slot or floppy disk drive and press Change disks. To finish the installation, remove all disks from the drive and press Finish installation.

1115.6088.12

1.3

E-6

Creating a new Software Configuration

CMU-K20/-K21/-K22/-K23/-K24

The VersionManager is closed and the CMU is rebooted. The new firmware options are now operational and listed in the Menu Select menu together with their version number. Besides, the last software configuration installed is automatically taken as the active one in the next measurement session.

Creating a new Software ConfigurationThe CMU handles base software versions and network options on a separate basis. Different versions of the base software can be combined with different options to create new firmware configurations. For example, it is possible to update the base software without affecting the associated network options or vice versa. Moreover, the same base software version can be installed several times and combined with different network options (and vice versa), so it may enter into several firmware configurations. If no compatible base software version can be found on the hard disk, then the CMU will refuse to install a new GSM MS software option selected in the software selection dialog (see previous section). Instead, it displays the following error message:

Press Back to installation to return to the software version selection dialog.

Select a base software version that is compatible to your GSM MS software option and press Install. Note: As a rule, firmware versions for the base system and for network options are compatible if they differ only in the last digit. GSM firmware versions 3.10 to 3.19 (if available) can be run together with base system version 3.10 to 3.19 (if available).

With a new base software version, it is possible to either update an existing configuration or create a new one. A dialog selecting between the two alternatives is opened: 1115.6088.12 1.4 E-6

CMU-K20/-K21/-K22/-K23/-K24

Creating a new Software Configuration

Note:

This dialog is skipped if the new base software version is not compatible with any of the existing configurations. An incompatible new base software must be installed as a new base software.

If you wish to add a new configuration to your hard disk, press Install as new base. To upgrade an existing configuration with the selected base software version in order to make it compatible to the new GSM MS software option, press Upgrade existing version. The existing version to be upgraded must be selected in an additional dialog. The installation is performed as described in section Software Installation or Update. After adding the new base software as a new configuration or updating the existing configuration, the CMU displays the following screen:

Press left softkey no 4 or 5 (Install next software...) and proceed as described in section Software Installation or Update to install the new GSM MS version and assign it to the new configuration.

1115.6088.12

1.5

E-6

Enabling Software Options

CMU-K20/-K21/-K22/-K23/-K24

Enabling Software OptionsA new CMU software option purchased is ready to operate after it is enabled by means of a key code supplied with the option. This key code is to be entered into the Option Enable popup window which in turn can be opened via from the Setup Options menu. For details refer to Chapter 4 of the CMU200/300 operating manual. Note: The five software options GSM400/850/900/1800/1900-MS and the supplementary options GPRS and EGPRS for GSM MS (CMU-K42/-K43) are part of a single software package termed GSM MS, so they must be installed or updated together. However, they must be enabled and operated separately. Software installation and enabling of software options are completely independent from each other.

1115.6088.12

1.6

E-6

CMU-K20/-K21/-K22/-K23/-K24


Contents2 Getting Started .................................................................................................... 2.1Preparing a GSM Mobile Phone Test..............................................................................................2.2 Non Signalling Mode ........................................................................................................................2.6 Signalling Mode ..............................................................................................................................2.14 Call Setup and Signalling Parameters....................................................................................2.14 Receiver Reports and Power Measurements ........................................................................2.20 Receiver Quality Measurements ............................................................................................2.22 Multislot Measurements with Mixed Modulation Schemes.....................................................2.24

1115.6088.12

I-2.1

E-11

CMU-K20/-K21/-K22/-K23/-K24

Preparing a GSM Mobile Phone Test

2 Getting StartedThe following chapter presents a sample GSM mobile test with the universal radio communication tester CMU. It is intended to provide a quick overview of the function groups GSM400/850/900/1800/1900-MS Non Signalling and GSM400/850/900/1800/1900-MS Signalling and their functionality and to lead through some basic tests that are commonly performed on GSM mobile phones. Before starting any measurement with the CMU, please note the instructions given in chapter 1 of the operating manual for the CMU basic unit for putting the instrument into operation. In chapters 2 to 4 of that manual you will also find information on customizing the instrument and the display according to your personal preferences. For installation instructions for the GSM400/850/900/1800/1900 software (CMU-K21/-K22/-K23) refer to chapter 1 of the present manual. The tests reported below include Connection of the phone and selection of the GSM function group, Power and modulation measurements in Non Signalling mode, Selection and measurement of signalling parameters, BER tests. The steps to perform are explained on the left side of each double-page together with the results obtained on the CMU screen. On the right side, additional information is given. We also point out alternative settings and related measurements which could not be reported in detail. The principles of manual operation are discussed in chapter 3. For a systematic explanation of all menus, functions and parameters including GSM background information refer to the reference part in chapter 4.

1115.6088.12

2.1

E-11


CMU-K20/-K21/-K22/-K23/-K24

Preparing a GSM Mobile Phone TestThis chapter describes how to use the CMU for GSM mobile phone tests. As a prerequisite for starting the session, the instrument must be correctly set up and connected to the AC power supply as described in chapter 1 of the operating manual for the CMU basic unit. Furthermore, the GSM software must be properly installed following the instructions given in chapter 1 of the present manual.

Step 1o I

Switch on the CMU using the mains switch at the rear. Check the operating mode of the instrument at the ON/STANDBY key on the front panel.

UNIVERSAL RADIO COMMUNICATION TESTER . CMU 200FUNCTIONMENU SELECT DATA CTR LHELP

1100.0008.02SYSTEMSETUP PRINT

Step 2Connect the bi-directional RF connector RF 2 of the CMU to the antenna connector of the mobile phone.M

DATAabc

VARIATIONG/n mV A

7 4 1 0

de f

8 5 2

ghi

9

DATA 1

jk l

m no

pqr

6

M/ B V W

DATA 2stu vwx yz

3 -

C k/m dBV F *1 D dBm dB U NIT...

_

*.

E

#

AUX 3

m ar k

s ym b

ON / OFFEXP/CMP

ENTERCON T/HALT

SPEECH

CONTROLCLR

1 AUX 1 AUX 2ABC

2

3GI H

DE F 5 8VW . S

4INS DEL

69XYZ

7STU

VOL

AUTO

AF IN

AF OUT

RF4 IN

RF 3 OUT

RF 2

RF 10 RCL

C

ESCAPE

INFO

RESET13 dBmMAX 13 dBmMAX 2 W MAX 50 W MAX

Supply the mobile phone with the correct operating voltage (battery or power supply).

Step 3Switch on the CMU by means of the ON/STANDBY key on the front panel.

The startup menu is displayed while the CMU performs a power-up test. After a few seconds the CMU displays the last menu used in the previous session. Press the RESET key to open the Reset popup menu. Select Reset and press the ENTER key. In the popup window opened, select Yes to confirm the instrument reset. The CMU indicates that it performs a general reset of all device settings and is then ready to carry out the following steps. The Reset popup menu is closed automatically.

1115.6088.12

2.2

E-11

CMU-K20/-K21/-K22/-K23/-K24 Additional Information...

Preparing a GSM Mobile Phone Test Alternative Settings and Measurements

... on Step 1Mains switch on the rear panel When the mains switch at the rear is set to the OFF position, the complete instrument is disconnected from the power supply. When it is set to the ON position, the instrument is in standby mode or in operation, depending on the position of the ON/STANDBY key on the front panel. ON/STANDBY key on the front panel The ON/STANDBY key at the front of the instrument determines whether the instrument is in standby mode or in operation. Standby mode: Only the reference frequency oscillator is supplied with operating voltage, and the orange LED (STANDBY) is illuminated. Operation: The green LED (ON) is illuminated and all modules of the instrument are supplied with operating voltage. chapter 1 of CMU manual

... on Step 2RF connection of the mobile phone A high-quality cable should be used for this connection, ideally with an attenuation of less than 0.5 dB. For portable phones, the car installation set supplied by telephone manufacturers can be used. Power supply for the mobile phone In case the mobile phone is operated from an external power supply, make sure that it is capable of supplying the maximum peak current required. As GSM mobile phones generate pulse-like RF signals, they often feature a pulse-shaped current consumption. Problems may arise if power supplies are used which cannot provide such currents with a constant voltage. The CMU provides two bidirectional RF connectors RF1 and RF2 differing by their permissible input and output levels. RF1 is the recommended standard connector for GSM mobile phones, RF2 for handheld phones (see data sheet). The unidirectional connectors RF4 IN and RF3 OUT are intended for connection of modules requiring high input levels or modules with low RF output levels. RF4 IN and RF3 OUT can also be used to connect GSM mobiles off the air via antennas. Input and output connectors can tab of be selected in the RF the Connect. Control menu. Startup menu The startup menu displays the following information: The startup procedure (Process) Instrument model, serial number and version of the CMU base software (Info) Installed hardware and software options and equipment (Options). Available software options are listed with their version numbers. Progress of the startup procedure (Startup bar graph). chapter 4 of CMU manual That chapter also contains information on customizing the CMU.

... on Step 3

1115.6088.12

2.3

E-11


CMU-K20/-K21/-K22/-K23/-K24

MENU SELECT

Step 4Press the Menu Select key to open the Menu Select menu.

The Menu Select menu indicates the function groups available. If a function group is selected the corresponding modes and measurement menus are indicated. Select the GSM900-MS function group. Select the Non-Signalling mode Select the Analyzer/Generator menu. Press the Enter key to activate the measurement selected and open the Analyzer/Generator menu.

1115.6088.12

2.4

E-11


Preparing a GSM Mobile Phone Test Alternative Settings and Measurements

... on Step 4Menu Select menu The Menu Select menu shows all function groups installed on your CMU. All function groups GSMxxx-MS are subdivided in the two measurement modes Non Signalling and Signalling, each containing a number of measurement menus. chapter 3 chapter 4 Frequently used measurement menus can be stored together with their function group and mode and assigned to one of the eight hotkeys. When needed for the next time, they can be called up by a single keystroke. See also chapter 4 of the CMU manual.

1115.6088.12

2.5

E-11

Non Signalling Mode

CMU-K20/-K21/-K22/-K23/-K24

Non Signalling ModeIn the Non Signalling mode, a GSM-specific RF signal can be generated and a RF signal with GSM characteristics can be analyzed. Compared to the Signalling mode test times may be reduced considerably. Moreover, the measurements are not restricted to the specified channel and MS output power ranges of the network. The most common application is module test and test of mobiles in a special test mode. In our example we use the GSM signal generated by the CMU itself to demonstrate the main features of the Non Signalling mode. This is analogous to the RF measurement example in the CMU operating manual.

Step 1The Analyzer/Generator menu contains softkeys and hotkeys to configure the RF generator signal of the CMU and to define the RF analyzer settings. Moreover, the current measurement results for power, frequency and phase errors of the received signal are displayed. At present, all parameters are set to default values. They can be directly changed by means of the softkeys and hotkeys. Userdefined parameters will be saved to the non-volatile RAM for later sessions when the CMU is switched off.

Proceed as outlined in section RF Non Signalling Measurements, chapter 2 of CMU200 operating manual to connect RF1 to RF2 via a coax cable. Open the Connection Control menu and perform the appropriate RF input and output settings. Adapt the Analyzer Settings Frequency setting to the expected input signal frequency (default generator frequency). Press Generator RF Level and the ON/OFF key to switch on the generator. The analyzer adapts itself to the RF input level (autoranging).

The measurement results are indicated in the P/t Norm. GMSK and Ext. Phase Error GMSK output fields. Select (press) the Power/t Norm. GMSK softkey.

1115.6088.12

2.6

E-11


Non Signalling Mode Alternative Settings and Measurements

... on Step 1Analyzer/Generator menu The Analyzer/Generator menu contains three with associated hotkeys used to Define the RF input signal path and the trigger settings (Analyzer Level) Set the CMU RF analyzer (Analyzer Settings) and determine the RF input signal that can be measured Control the RF generator (Generator) and define the parameters of the RF output signal generated. Selecting a definite training sequence (TSC) or bit modulation or transmission mode in the Generator Modulation panel implies that signals with these characteristics are generated. Selecting a definite TSC in the Analyzer Settings panel implies that only signals with this TSC are analyzed. chapter 4, p. 4.2 ff. The Analyzer/Generator settings are also provided in the Analyzer and Generator tabs of the Connection Control menu. See also notes on Softkeys and hotkeys on p. 2.11.

The assignment between carrier frequency and channel number is according to GSM specifications. As the CMU simulates a base station, the generator signal corresponds to the downlink (signal direction from the base station towards the mobile station), the signal analyzed corresponds to the uplink (signal direction from the mobile station towards the base station). The channel/frequency assignment changes accordingly. The RF frequency can be set in multiples of 200 kHz. With an additional Frequency Offset, an RF signal with an arbitrary frequency that is in the range supported by the tester can be generated and analyzed. In general, the RF generator level is set to be different for the used timeslot and unused timeslots. The level of the unused timeslots is defined relative to the level in the used timeslot. Measurement and Generator State The state of the Power/t Norm. GMSK measurement is indicated in the corresponding softkey (measurement control softkey) and above the output fields for the results. The state of the RF generator is indicated in the Generator RF Level softkey. For ongoing measurements, the results in the output fields are constantly updated. All measured quantities refer to the current burst. The default tolerance template for the power ramp is defined according to GSM specifications. For various reasons, an output field may fail to show a valid measurement result (indication "---"): The analyzer settings do not match the properties of the input signal. The input signal is missing. The measurement is switched off (OFF is indicated in the softkey controlling the measurement).

The current options for the measurement status are ON (default) and OFF. A third state, HLT, occurs after a single-shot measurement is terminated (see below). Once selected, the Power or Modulation measurement can be switched off and on again by means of the toggle key ON/OFF. Generators may also be switched on (state ON) and off (state OFF) by means of the ON/OFF key.

Max. Level The autoranging mechanism adjusts the RF input path to the applied signal. Alternatively, the expected signal level (for GMSK-modulated GSM signals, the average RF input level plus an appropriate margin of a few dB) can be set via Analyzer Level RF Max. Level.

Chapter 4, p. 4.72 ff. The permissible range Max. Level depends on the RF connector and the external attenuation used.

1115.6088.12

2.7

E-11

Non Signalling Mode

CMU-K20/-K21/-K22/-K23/-K24

Step 2Press the selected Power/t Norm. GMSK softkey again to call up the Power Configuration menu.

In the Control tab, the Power Configuration menu defines the scope of the Power measurement. The settings offered in this menu are discussed in section General Settings in chapter 3. We pick just one example, limiting the number of bursts measured. Press the ON/OFF key or the rotary knob to expand the table. Select Single Shot in the Repetition line. Press the ESCAPE key or the Power softkey again to close the Power Configuration menu and return to the main menu.

The Power measurement is stopped after one statistic count. The status indication next to the Power softkey is set to HLT.

Step 3Press the Power hotkey to switch over to the graphical menu Power.

The Power menu shows the power of the current burst as a function of time. Together with the burst power, a tolerance template as specified in the GSM standard (here: for GMSK-modulated normal bursts) is displayed. Settings (at present, the default settings) and scalar results are displayed in two parameter lines above the diagram and in a message box positioned in the center of the diagram. Various tools allowing to take a closer look at the measurement results are provided in the graphical measurement menu.

1115.6088.12

2.8

E-11



... on Step 2Power Configuration menu The Power Configuration menu contains three tabs defining Measurement control and statistical settings (Control), The tolerance template for the burst (Limit Lines), PCL-dependent limits for the average burst power (Limits) chapter 3. Settings made in the Power Configuration menu apply to power measurements only. Settings made in the Connect. Control menus apply to the entire function group and mode GSM900-MS Non Signalling. chapter 3. The Statistic Count is defined in the Control tab of the Power Configuration menu. The stop condition On Limit Failure should be selected if the limit check represents the main purpose of the measurement. The limits can be modified in the Limit Lines tab of the Power Configuration menu. CMU manual See the sections on measurement control in chapter 3 and 5.

Repetition mode and Stop Condition If no stop condition is imposed (Stop Condition = None), the Repetition mode determines whether the measurement is Continued until explicitly stopped by the operator (Continuous), Stopped after one statistic count (Single Shot).

By default, a statistic count comprises 100 bursts. With Stop Condition = On Limit Failure, the measurement is stopped after the first burst which is out of tolerance.

Measurement in the HLT state The average and peak power of the last burst measured is indicated in the output fields Average and Peak. In contrast, the modulation measurement is still running. The results for the frequency and phase errors are periodically updated.

... on Step 3Power menu The diagram in the Power menu, application Power/t Norm. GMSK shows a normal burst with a length of 148 bits (plus a guard period of 8.25 bits). The time scale of the diagram ranges from 10 bits to 156 bits covering the useful part, the rising and falling edges of the burst. The ordinate ranges from 80 dB to +10 dB, the 0-dB reference level is equal to the carrier power. Note that settings made previously (Power Configuration menu) are preserved in the whole measurement group. Accordingly, the status of the measurement is still HLT. The diagram is fixed showing the last burst measured. chapter 4, p. 4.9 ff. The GSM power template is defined relative to the carrier power. For low signal powers, a looser absolute limit is to be applied at the beginning and the end of the power ramp (areas 1, 2, 7, and 8). This yields the distorted template that we observe in the present example.

1115.6088.12

2.9

E-11

Non Signalling Mode

CMU-K20/-K21/-K22/-K23/-K24

Step 4Press the Marker/Display softkey twice to change the hotkeys displayed below the diagram.

Press the Display Area hotkey to open a window offering a list of different zoom areas. If you select Left Upper Corner the CMU zooms in on the left upper corner of the burst. Press the Display/Marker softkey twice and the Ref R hotkey. Enter an abscissa value (in bits) to position a reference marker onto the trace. The coordinates (time and burst power) of the reference marker are displayed in the second parameter line. For the next step we'll take advantage of the fact that the configuration menu is accessible from the graphical menu as well.

Step 5Press the Power/t Norm. GMSK softkey twice to reopen the Power Configuration menu.

Press ENTER or the rotary knob to expand the table. Select Continuous from the Repetition field to restart the measurement and confirm with ENTER or by pressing the rotary knob. From the Display Mode field, select Maximum. Press ESCAPE or the P/t Norm. GMSK softkey again to close the configuration menu. Instead of the current burst power, the diagram shows the maximum burst power measured at each time. As no stop condition is set, the measurement will be running until it is explicitly terminated.

1115.6088.12

2.10

E-11



... on Step 4Softkeys and hotkeys To enlarge the diagram area of the graphical measurement menus the left softkey column is suppressed. The functionality of each softkey on the right side is extended by hotkeys assigned to the softkeys. These hotkeys are displayed across the hotkey bar below the diagram when the softkey is selected. Some of the softkey/hotkey combinations offer settings that can be also accessed via configuration menus. For example, the Analyzer Level settings are equivalent to the settings in the Input Level and Trigger section in the Analyzer tab of the Connection Control menu. Identical settings overwrite each other; the last value entered is valid for the whole function group and test mode. Markers Markers are a graphical tool used to locate points on a trace and read out their coordinates. A reference marker and two delta markers may be defined in the Power menu. measures the absolute level of the The reference marker trace, the delta markers and measure the absolute level or (if set to relative) the distance between their position and the reference marker. chapter 4, p. 4.9 ff. The Analyzer Level softkey configures the input level and external attenuation as well as the trigger settings. The Analyzer Settings softkey determines which kind of RF signal can be analyzed. The Generator Settings softkey determines the RF signal generated.

The Marker/Display softkey sets markers and D-lines and determines the display area. chapter 4, p. 4.9 ff. In addition to markers, a D-line can be used to measure a particular level in the diagram.

... on Step 5Display mode If the measurement extends over several bursts the CMU calculates four different traces one of which can be selected in the Display Mode field. The purpose of the four traces is to give an overview of the range and arithmetic mean of the levels detected at any point on the time axis. The following traces can be displayed: Current Current burst level Maximum Maximum of all burst levels measured Minimum Minimum of all burst levels measured Average Weighted average of all burst levels measured, see averaging prescription in chapter 3. The Statistic Count input field defines how many evaluation periods form a statistics cycle. For GSMxxx-MS Non Signalling measurements an evaluation period is equal to the propagation time of a normal burst (this definition holds even if a continuous carrier signal is transmitted). In our example the statistics cycle comprises 100 bursts (default value). chapter 3. To refine the statistical evaluation, a suitable combination of the statistic count, repetition mode, stop condition and display mode can be selected. chapter 4, p. 4.28 ff. In addition to the Power/t Norm. GMSK measurement, several test applications assessing the behavior of the average burst power over several timeslots (P/Slot Graph, P/Slot Table) or frames (P/Frame) can be selected (softkey Application).

1115.6088.12

2.11

E-11

Non Signalling Mode

CMU-K20/-K21/-K22/-K23/-K24

ESCAPE

Step 6Press the ESCAPE key to close the Power Configuration menu and return to the main menu.

The trace is now continuously measured and updated in the display. With the display mode Maximum, which is indicated in the upper right corner of the diagram, trace values will be replaced only if a current measured value at a particular test point exceeds all values measured before at the same test point.

Step 7Press the Menus softkey to display the measurement groups available in the hotkey bar. Press the Modulation hotkey to open the Modulation menu.

The Modulation menu displays the results of the phase and frequency error measurement. The trace represents the phase error of the current burst as a function of time. Below, a table displays the extreme value of the phase error and the RMS phase error, the origin offset, the I/Q imbalance, and the frequency error. The detected training sequence (TSC), average power of the current burst and the statistic count are shown in addition.

1115.6088.12

2.12

E-11



... on Step 7Phase and frequency errors GSM equipment can use different modulation schemes; the basic scheme is GMSK modulation, which is a constantenvelope, binary, differential phase-shift keying scheme. It is important that the modulation scheme is adhered to as strictly as possible. GSM specifies a peak phase error of max. 20, a RMS-weighted phase error of max. 5 and a frequency error of max. 0.05 ppm of the transmit frequency. The limits may be modified in the Limits tab of the Modulation Configuration Menu which is opened by pressing the selected Ext. Phase Err. GMSK softkey once again. The Modulation Configuration menu is analogous to the Power Configuration menu explained on the previous pages. According to the requirements of the measurements the two configuration menus differ in two points: Phase errors are relevant within the useful part of the burst. Therefore, a fixed upper and lower limit for the phase error is specified. It is not necessary to discriminate below). between different areas of the burst (see item The absolute value of the phase error is a measure of the quality of modulation, whereas the sign is of secondary interest. This is why the display modes Minimum and Maximum can not be selected separately, the CMU displays the extreme values instead (display mode Minimum/Maximum). Measurement curve The diagram in the Modulation menu shows the useful part of a normal burst with a length of 148 bits, The time scale of the diagram, ranging from 0 bits to 146 bits, is thus shorter than in the Power/t Norm. GMSK diagram. The ordinate is symmetric around 0 , ranging from 20 dB to +20 dB. Statistical quantities The table below the phase error diagram gives an overview of the phase error averaged over the current burst (Phase Error RMS), the extreme value of the current phase error (Phase Error Peak), the current Origin Offset and I/Q Imbalance, the current frequency error, and the statistical distribution of these three quantities. The values in the three columns are calculated as follows: The Current column contains the frequency error, RMSaveraged phase error and peak (Max./Min.) phase error for the current burst. The Average column contains the three quantities averaged over the last statistics cycle. The Maximum column contains the extreme values of the three quantities within all bursts measured. chapter 4, p. 4.41 ff. chapter 4, p. 4.38 ff. The measurement principle for phase and frequency errors is explained at the beginning of section Measurement Menu (Modulation GMSK). For configuration settings see section Measurement Configurations (Modulation Configuration). As a second modulation scheme, the CMU supports 8PSKmodulated traffic channels (in the so-called EDGE channels).

chapter 3. In this chapter a comprehensive description of measurement control and on the definition of statistical quantities is given. chapter 4, p. 4.41 ff. As a last measurement group in Non Signalling mode, the Spectrum measurement assesses the off-channel power due to the modulation and due to switching.

1115.6088.12

2.13

E-11

Signalling Mode

CMU-K20/-K21/-K22/-K23/-K24

Signalling ModeIn the Signalling mode the CMU first transmits a control channel signal to which the mobile is able to synchronize. A call can then be established from either the CMU or the mobile. The measurement must be synchronized to the signal transmitted by the mobile; an external trigger signal can not be used.

Call Setup and Signalling ParametersThe signalling processes and configurations are controlled via the Connection Control popup menu. A control channel signal is switched on and the second of several Connection tabs contained in the Connection Control popup menu is automatically displayed when the Connection test mode is selected (see Menu Select menu on page 2.4; for the following examples, GSM1800-MS Signalling Meas. with the Overview menu was selected, and another RESET was performed).

Step 1The Connection (Signal On) tab indicates the current signalling states, the characteristics of the mobile phone and those of the and the signals generated by the CMU MS under test. In addition the network identity and the characteristics of the input and output connectors are shown. The softkeys on the right side of the menu lead to other signalling states. The Main Service and Network Support softkeys are for switchover to GPRS signalling tests.

The Wideband Power softkey shows the current status of the wideband peak power measurement and its ratio to the maximum input power (Max. Level) set in the MS Signal tab menu. At present, the wideband power measurement is switched on, however, no signal is received because no call connection with the mobile phone has been established.

credit card format

Step 2Insert a test SIM card of the appropriate size into the phone and switch on.1ABC 2

GSM TEST SIMCRT-Z2 1039.9005.02

3GI H

DEF 5 8VW . S

4 7STU 0 RCL

69XY Z

plug-in format

C M

If requested, enter the PIN number followed by #. (PIN No. of Rohde & Schwarz test SIM card: 0000). Make sure that your mobile is connected to RF 2 (default input/output).

1115.6088.12 2.14 E-11


Signalling Mode Alternative Settings and Measurements

... on Step 1BS Signal The CMU is able to generate two different RF carrier signals (traffic channel and BCCH control channel) which can be configured separately. This allows a complete simulation of what happens in a real GSM network. chapter 4, p. 4.168 ff. The control and traffic channels are configured in the BS Signal tab of the Connection Control menu. To access this card press the associated hotkey. chapter 4, p. 4.176 ff. The network identity and other parameters characterizing the network are configured in the Network tab of the Connection Control menu. To access this card press the associated hotkey (see below). Input/output connectors and external attenuations are configured tab. in the RF /

Network Identity, RF The network is identified by the three code numbers MCC (mobile country code), MNC (mobile network code) and NCC (national color code). These codes are transmitted to the mobile station on the control channel. The CMU uses the default settings shown in the diagram on the left side. Input/output connectors suitable for the type of measurements and signal levels must be chosen see section RF connection on page 2.3. An external input/output attenuation value can be specified in order to compensate for known attenuations of the input/output signal like those caused by cables.

GPRS signalling With option CMU-K42 the CMU is also able to set up a TBF connection to a GPRS mobile phone and perform transmitter and receiver tests in a GPRS test mode.

chapter 4, p. 4.195 ff.

... on Step 2SIM card, test SIM Two types of SIM card are specified for use in the GSM system, one the size of a credit card and the considerably smaller plug-in SIM of about 15 x 20 mm. One SIM card must be inserted in the mobile phone in order to set up a call. However, it is also possible to make an emergency call without any card by entering 112. Most mobile phones require a socalled test SIM card in order to test the sensitivity (bit error rate and related quantities) in a test mode. A test SIM card is available from Rohde & Schwarz with the designation CRT-Z2 (id. no. 1039.9005.02). It features credit card size and can be easily converted to "plug-in" format.

Pin number Use care when entering the PIN number as only three false tries are allowed before the card is automatically blocked. It can be unblocked by entering the PUK number which is either known or can be obtained from the company that issued the card. See also the appropriate section in the operating manual of your mobile phone.

1115.6088.12

2.15

E-11

Signalling Mode

CMU-K20/-K21/-K22/-K23/-K24

Step 3Press the Network hotkey. The Network tab is displayed.

The Network tab defines a variety of parameters concerning the network and the operating mode of the mobile station. The purpose of these settings is to simulate the operating conditions of a mobile station in the GSM network as realistically as possible. Many of the settings have a direct impact on the speed of the Signalling measurements. Press the Connection hotkey to return to the Connection (Signal On) tab.

Step 4Press the Connect Mobile softkey.

The header message Paging in progress is displayed. When the mobile has synchronized to the BS signal and starts ringing, the Connection (Alerting) tab is displayed. The Connection (Alerting) tab indicates the most important parameters characterizing the mobile phone (MS Capabilities).

1115.6088.12

2.16

E-11



... on Step 3Network parameters The purpose of network parameter settings in the mobile test can be rather different from the original purpose (in the real GSM network). We illustrate this with two examples: The BA list (base station allocation list) informs the mobile about the channels available in a given area. The mobile uses the BA list to determine to which RF channel it will receive the next handover request. The CMU uses the BA list to test a mobile when the synthesizer is jumping continuously from channel to channel and the software has to organize this, to evaluate and report the results. In the DTX (discontinuous transmission) mode the mobile transmits traffic channel frames only when there is voice or data to be transmitted. This mode is used mainly in order to save mobile battery power. In the test mode, a DC current measurement during DTX will provide information about a possible leaking component of the mobile. No continuous Power measurements can be done while DTX is enabled. chapter 4, p. 4.176 ff.

... on Step 4Location update The information transmitted by the CMU on the control channel requests the mobile phone to perform a location update procedure after switching-on. This is similar to a registration procedure in analog and other digital networks and serves to inform the base station that a certain mobile has been switched on now and is available for calls. MS Capabilities The MS Capabilities list shows the basic properties of the connected mobile station which are transmitted to the CMU. The international mobile subscriber identity (IMSI) consists of the 3-digit mobile country code, the 2-digit mobile network code and the 10-digit mobile subscriber id. no. The international mobile station equipment identity (IMEI) consists of the 6-digit type approval code, the 2-digit final assembly code, the 6-digit serial no. and the 1 or 2-digit software version no. The following hardware-related parameters determine the maximum output power of the mobile station: Power class (1 to 5) MS revision level (phase I or II) chapter 4, p. 4.176 ff. The Location Update parameter in the Network tab determines in which cases a location update is performed.

chapter 4, p. 4.155 ff. A comprehensive list of mobile station properties is displayed in the Call Established signalling state. Power classes and GSM revision levels are listed with their maximum output power in section Limits for the Average Burst Power in chapter 4.

1115.6088.12

2.17

E-11

Signalling Mode

CMU-K20/-K21/-K22/-K23/-K24

Step 5Accept the call at your phone. Press Connect. Control to reopen the Connection Control menu.

The Connection (Call Established) presents a comprehensive list of the signalling parameters for the current connection (see MS Capabilities on page 2.17). The power control level of the mobile station and the parameters of the traffic channel signals transmitted by the CMU can still be configured in the MS Signal and BS Signal tabs of the Connection Control, respectively. Press the Escape key to close the Connection Control menu and return to the Overview menu.

1115.6088.12

2.18

E-11



... on Step 5Power control level (PCL) Dynamic power control is used in GSM networks to reduce the output power of the mobile station as far as possible. In practice the base station sets the mobile power on a dimensionless scale of power control levels (PCL) ranging from 0 to 31. In GSM900, PCL 0 corresponds to the largest nominal output power (39 dBm), power control levels between 16 and 31 can be set for phase II mobiles only. In contrast to the PCL the power class characterizes the nominal maximum output power of the mobile. Depending on the power class of the mobile the range of possible PCL settings may be restricted. Traffic channel The channel number of the BS traffic channel signal is defined according to GSM specifications as explained for the Non Signalling mode (downlink, see Analyzer/Generator menu on page 2.7). The traffic channel can be fixed or changed periodically (frequency hopping). Frequency hopping is defined by means of one of the four hopping sequences A, B, C, D. With the CMU basic unit timeslots 2 to 6 may be selected for the traffic channel because the timeslots 0, 1, and 7 are occupied by the BCCH and for reconfiguring. chapter 4, p. 4.116 ff. PCL levels and power classes are listed in section Limits for the Average Burst Power in chapter 4.

chapter 4, p. 4.168 ff. Besides the four GSM standard hopping sequences A to D arbitrary sequences consisting of up to 64 channel numbers may be defined and used.

Out-of-tolerance power measurements If a power measurement is out of tolerance, please ensure that the attenuation of any cables and/or antenna couplers used is being taken into account by the CMU. As some GSM power levels must be within 2 dB of the nominal value given in the specifications, even a small attenuation can result in an out-of-tolerance measurement. External attenuation values for each input/output may be entered in the RF Control menu tab of the Connect.

The cables, RF connections and antenna couplers must also be in good condition for satisfactory measurements. Dirty or broken RF connections can cause problems at the high frequencies used by GSM networks.

1115.6088.12

2.19

E-11

Signalling Mode

CMU-K20/-K21/-K22/-K23/-K24

Receiver Reports and Power MeasurementsBesides the signalling parameters discussed above the receiver reports of the mobile station are transmitted to the CMU. Power and modulation measurements can be performed as in the Non Signalling mode.

Step 1The Overview menu indicates the most important settings in the function group GSM900-MS Signalling and the main results of the Power and Modulation measurements (output fields Ext. Phase Err. GMSK). Moreover the receiver reports of the mobile station are displayed. Power and Modulation measurements can be performed in close analogy to the measurement of GSM signals in the Non Signalling mode. The differences between the two modes are related to the settings which can be made at the mobile station.

Step 2Press the Power hotkey to switch over to the graphical menu Power.

The Power menu shows the power of the current burst as a function of time. Like in the Non Signalling mode the menu contains an Application (Applic. 1 or 2) softkey. Press the Applic. 1 softkey to change the hotkeys displayed below the diagram. Press the P/PCL hotkey to measure the average burst power as a function of the mobile's power control level. Press the MS Signal softkey to check the PCL (PCL hotkey) and traffic channel number (Channel hotkey) set.

Step 3Press the Menus softkey and the Receiver Quality hotkey to switch over to the Receiver Quality menu.

1115.6088.12

2.20

E-11



... on Step 1MS Receiver Reports GSM mobile phones continuously measure the signal strength and quality of several nearby base stations. The measured values for the active base station (serving cell BTS) are regularly sent to the CMU in the so-called measurement reports. The received signal input level (RX Level) is expressed in terms of dimensionless power levels ranging from 0 to 63. These levels depend linearly on the absolute signal levels measured in dBm. A high power level implies a high received signal input level. The received signal quality (RX Quality) is expressed in terms of dimensionless quality levels (actually error levels) ranging from 0 to 7. The quality levels depend linearly on the logarithm of the bit error rate. A high quality level implies a high bit error rate and thus a poor received signal quality. chapter 4, p. 4.141 ff. The exact definition of RX Level and RX Quality is given in section Panel MS Rcv. Reports Received Results of the Mobile Phone. The dependence of RX Level and RX Quality on the CMUs output level can be quickly checked by varying the TCH Level in the used timeslot. Different TCH levels can be set in the used timeslot and in the unused timeslots. This is useful for some tests specified by GSM.

... on Step 2P/PCL Measurement The P/PCL measurement forms the second application in the measurement group Power. In this application, the average burst power of the mobile can be measured over the whole range of power control levels and for up to three different channels at once. The PCLs and channels to be measured can be selected; the total measurement time is below 3 s. chapter 4, p. 4.101 ff. The different applications Power/t Norm. GMSK, P/PCL etc. split up the measurement group Power in several related subgroups. For a general discussion of measurement control and applications see chapters 3 and 5. PCL/Channel and Trigger The PCL set for the mobile station and the traffic channel number can be checked and modified, if required, in the Power menu. This is in contrast to the Non Signalling mode where no settings concerning the device under test can be made. Finally the two modes differ in the trigger modes available: In the Non Signalling mode an external trigger signal may be used whereas in the Signalling mode the measurements must be triggered by the input signal (Free Run, RF Power, IF Power mode) or by the CMU's signalling unit (Signalling trigger). chapter 4, p. 4.101 ff. The frame trigger signal (Signalling trigger mode) is also fed to pin 2 of the AUX 3 connector where it can be tapped off to synchronize external devices to the CMU's TDMA timing.

1115.6088.12

2.21

E-11

Signalling Mode

CMU-K20/-K21/-K22/-K23/-K24

Receiver Quality MeasurementsReceiver Quality measurements evaluate parameters which characterize the quality of transmission on the complete signal path between CMU and mobile station. To this purpose the bits sent to the mobile station are looped back and retransmitted. The CMU compares the bits received with those sent and can thus calculate the percentage of faulty bits. Most but not all mobiles require a test SIM card to enter the loop-back mode (see SIM card, test SIM on page 2.15).

Step 1The Receiver Quality menu controls the receiver quality tests and displays the measurement results together with the RX Level and RX Quality of the serving cell. This facilitates a comparison between the results reported by the mobile (RX Quality) and the sensitivity test results. Press the Application softkey to display all applications of the Receiver Quality measurement group. Select BER. Press the BER Meas. Mode hotkey and select Burst by Burst.

Step 2Press the selected BER softkey again. The Receiver Quality Configuration menu is opened.

The Control tab contains the parameters configuring the Receiver Quality measurement. Most parameters are equal or analogous to the ones used in Power or Modulation measurements. Major differences occur in the measurement modes available (Control tab, ) and in the definition of the statistics count.

1115.6088.12

2.22

E-11



... on Step 1Applications Within the Receiver Quality measurement group, the repetition modes BER (single shot bit error rate tests) and BER Average (continuous bit error rate tests) are treated as different applications. For single shot measurements, up to ten different test setups with independent parameters can be configured (see Control tab in the Receiver Quality Configuration menu). Measurement Mode A number of different quantities characterizing the quality of transmission are defined: Bit error rate (for class II and class Ib bits) Residual bit error rate (for class II and class Ib bits) Frame erasure rate The type of quantities measured depends on the measurement mode (BER, RBER/FER, or Burst by Burst). In the Burst by Burst mode which is specified for GSM phase II and phase II+ mobiles, only bits without error protection are transmitted. This enhances the speed of the bit error rate test (fast BER test). chapter 4, p. 4.133 ff. For a general discussion of measurement control and applications see chapters 3 and 5.

chapter 4, p. 4.133 ff. The bit classes and measured quantities are explained at the beginning of section Measurement Menu Receiver Quality.

... on Step 2Statistics In the framework of sensitivity tests the basic evaluation period is equal to the frames used by the speech coder and consisting of 260 bits. Bursts and TDMA frames are irrelevant. A statistics cycle thus consists of a definite number of frames. Failed Receiver Quality Test If a BER test fails check the following: 1. Ensure that the attenuation of any antenna coupler and/or cables used is being taken into account by the CMU. During the test the mobile receiver is being tested with very low RF signal levels, and even a small attenuation can cause the CMU to show a fail indication. 2. An external signal from a real network may interfere with the signal sent from the CMU to the mobile, in particular during BER tests where the output level of the CMU is reduced to as low as -104 dBm. The BER test should ideally be performed in a shielded room, however, if this is not possible, the channel(s) used for the test should be changed. If different results are obtained on neighboring channels, the problem is likely to be due to external interferences. chapter 3 and 4.

1115.6088.12

2.23

E-11

Signalling Mode

CMU-K20/-K21/-K22/-K23/-K24

Multislot Measurements with Mixed Modulation SchemesIn an EGPRS test mode connection, a packet switched data channel is allocated between the CMU and the MS under test. The MS uses the enabled timeslots for the transmission of 8PSK modulated bursts. In addition, it is periodically stimulated to transmit a single GMSK-modulated burst. In a P/t Multislot measurement, it is possible to specify the modulation scheme for each measured timeslot of an uplink multislot configuration. Only a burst sequence with matching modulation pattern will be measured. This feature can be used to pick out the occasional GMSK burst events in the uplink signal and obtain the burst power of 8PSK- and GMSK modulated bursts in a single measurement. Measurement task Connection Measure the power of the GMSK-modulated bursts that the MS transmits while it operates in EGPRS mode. Display the power together with the power of the adjacent (8PSK-modulated) bursts and perform a limit check for all bursts. To set up the appropriate EGPRS connection 1. Connect the mobile to the CMU and switch on. 2. In the Menu Select menu, select the appropriate GSM band and the measurement menu Signalling Power P/t Multislot. 3. In the Connection tab of the Connection Control menu opened, select Network Support: GSM + EGPPRS, Main Service: Packet Data. 4. Select one of the test modes A or B for transmitter or loopback tests (Service Selection: Test Mode A or Test Mode B). If you select test mode B, then open the Network tab of the Connection Control menu and set Test mode with ACK in the Packet Data section to On. 5. Set up the EGPRS connection to the mobile until the CMU enters the TBF Established state and the Connection Control menu is closed automatically. Measurement configuration After closing the Connection Control menu, the measurement menu for the P/t Multislot application is shown with default settings. To adjust the UL and DL signal and display settings 6. Press MS Signal Slot Config. and enable 2 or more consecutive uplink timeslots. 7. Press the P/t Multislot measurement control softkey and adjust the Slot Count and Meas. Slot to your UL signal configuration. 8. Press Display Modulation View and select GMSK modulation for one of the measured and displayed timeslots.

The GMSK and 8PSK bursts are displayed together with the appropriate limit line template. In the examples above both bust types pass the limit check.

1115.6088.12

2.24

E-11

CMU-K20/-K21/-K22/-K23/-K24


Contents3 Manual Control ..................................................................................................... 3.1Menu Structure .................................................................................................................................3.1 Test Modes...............................................................................................................................3.1 Configurations ..........................................................................................................................3.2 Measurement Groups ..............................................................................................................3.3 General Settings ...............................................................................................................................3.5 Menu Overview .................................................................................................................................3.9 GSM-MS Non Signalling General Configurations .................................................................3.9 GSM-MS Non Signalling Power and Modulation.................................................................3.10 GSM-MS Non Signalling Spectrum .....................................................................................3.11 GSM-MS Signalling General Configurations I .....................................................................3.12 GSM-MS Signalling General Configurations II ....................................................................3.13 GSM-MS Signalling Power and Modulation ........................................................................3.14 GSM-MS Signalling Spectrum and Receiver Quality ..........................................................3.15

1115.6088.12

I-3.1

E-11

CMU-K20/-K21/-K22/-K23/-K24

Menu Structure

3 Manual ControlThis chapter gives a brief survey of the operating concept and the structure of the user interface for GSM mobile p

Documents

CMU200 User Manual R&S English