AVR 510 om.pdf

AVR 510 Audio/Video ReceiverOWNERS MANUAL

COAXIAL

THEATER5 CH STEREO HALL 123-STEREOPRO LOGICDIGITAL

DTSDOLBY D

PCMMP3

NIGHT MULTIOPTICAL ANALOG OSD

LFE

0 CL 0

1 2 3 1 2 3

MEMORY PRESETSLEEP

AUTO

5.1 LOGIC 7 CMVMAx NF

MUTE TUNED ST O

ORO

O

LSO

ORSO

O

Power for the Digital Revolution.

2 TABLE OF CONTENTS

3 Introduction4 Safety Information4 Unpacking5 Front Panel Controls7 Front Panel Information Display9 Rear Panel Connections

11 Main Remote Control Functions14 Zone II Remote Control Functions15 Installation and Connections18 System Configuration20 Input Setup20 Surround Setup21 Delay Settings22 Speaker Setup23 Output Level Adjustment23 Crossover Frequency24 Manual Output Level Adjustment26 Operation26 Basic Operation26 Source Selection27 Surround Mode Chart28 Surround Mode Selection28 Digital Audio Playback28 Selecting a Digital Source30 Tuner Operation31 Tape Recording31 Front Panel Input/Output

Connections31 Output Level Trim Adjustment32 6-Channel Direct Input33 Advanced Features33 Display Brightness33 Turn-On Volume Level33 Semi-OSD Settings35 Multiroom Operation36 Programming the Remote36 Direct Code Entry36 Auto Search Method36 Code Readout37 Learning Codes37 Erasing Learned Codes37 Macro Programming38 Programmed Device Functions39 Volume Punch-Through39 Channel Control Punch-Through40 Reassigning Device Control

Selectors41 Function List43 Setup Code Tables53 Troubleshooting Guide53 Processor Reset54 Notes55 Technical Specifications

AVR 510 Audio/Video Receiver

Typographical ConventionsIn order to help you use this manual with the remote control, front panel controls and rear panelconnections, certain conventions have been used.

EXAMPLE (bold type) indicates a specific remote control or front panel button, or rear panel connection jack

EXAMPLE (OCR type) indicates a message that is visible on the front panel information display

EXAMPLE (outlined type) indicates a lit indicator in the front panel information display

1 (number in a square) indicates a specific front panel control

` (number in a circle) indicates a rear panel connection

a (number in an oval) indicates a button or indicator on the remote

A (letter in a square) indicates an indicator in the front panel display

(letter in an oval) indicates a button on the Zone II remote

3 INTRODUCTION

Introduction

Thank you for choosing Harman Kardon!With the purchase of a Harman Kardon AVR 510 you are about to begin many years oflistening enjoyment. The AVR 510 has been custom-designed to provide all the excitementand detail of movie soundtracks and everynuance of musical selections. With onboardDolby* Digital and DTS decoding, the AVR 510delivers six discrete channels of audio that takeadvantage of the digital soundtracks from thelatest DVD and LD releases and DigitalTelevision broadcasts.

While complex digital systems are hard at work within the AVR 510 to make all of thishappen, hookup and operation are simple.Color-keyed connections, a programmableremote control, and on-screen menus make theAVR 510 easy to use. To obtain the maximumenjoyment from your new receiver, we urge youto take a few minutes to read through thismanual. This will ensure that connections tospeakers, source playback units and otherexternal devices are made properly. In addition,a few minutes spent learning the functions ofthe various controls will enable you to takeadvantage of all the power the AVR 510 isable to deliver.

If you have any questions about this product,its installation or its operation, please contactyour retailer or custom installer. They are yourbest local sources of information.

Description and FeaturesThe AVR 510 is among the most versatile andmulti-featured A/V receivers available, incorpo-rating a wide range of listening options. Inaddition to Dolby Digital and DTS decoding fordigital sources, a broad choice of analog sur-round modes are available for use with sourcessuch as CD, VCR, TV broadcasts and theAVR 510s own FM/AM tuner. Along with DolbyPro Logic*, Dolby 3 Stereo and custom Hall andTheater modes, only Harman Kardon receiversoffer Logic 7 to create a wider, more envelop-ing field environment and more defined fly-overs and pans. Another Harman Kardon exclu-sive is VMAx, which uses proprietary process-ing to create an open, spacious sound fieldeven when only two front speakers are avail-able. Finally, the AVR 510 is among the veryfew A/V receivers that offer decoding of MP3data, so that you may listen to the latest musicselections directly from compatible computersor playback devices with the power and fidelityyou expect from Harman Kardon.

In addition to providing a wide range of listen-ing options, the AVR 510 is easy to configure sothat it provides the best results with yourspeakers and specific listening-room environ-ment. On-screen menus make it simple to entersettings for speakers, inputs and delay times,while our exclusive EzSet remote measures asystems sound levels and automatically cali-brates them for perfectly balanced soundfieldpresentation.

For the ultimate in flexibility, the AVR 510 fea-tures connections for four video devices, allwith both composite and S-Video inputs. Twoadditional audio inputs are available, and atotal of six digital inputs make the AVR 510capable of handling all the latest digital audiosources. For compatibility with the latest DVDplayers and digital video products, the AVR 510also features component video switching.

Coax and optical digital outputs are availablefor direct connection to digital recorders, andboth the front panel analog audio/video andcoaxial digital jacks may be switched to outputs for use with portable recorders aHarman Kardon exclusive. Two video recordingoutputs, preamp-out/main-in jacks, and a six-channel input make the AVR 510 virtuallyfuture-proof, with everything needed to accom-modate tomorrows new formats right onboard.

The AVR 510s flexibility and power extendbeyond your main home-theater or listeningroom. The AVR 510 includes a sophisticatedmultizone control system that allows you toselect one source for use in the main room anda different one in a second room. Completecontrol over volume is possible with a separateinfrared control link. To make it easy to operatethe AVR 510 from a remote room, a separateZone II remote is included.

The AVR 510s powerful amplifier usestraditional Harman Kardon high-current designtechnologies to meet the wide dynamic rangeof any program selection.

Harman Kardon invented the high-fidelityreceiver more than forty-seven years ago. Withstate-of-the-art circuitry and time-honored cir-cuit designs, the AVR 510 is one of the finestreceivers ever offered by Harman Kardon.

n Onboard Dolby Digital and DTSDecoding Using Crystal Chip Technology

n Harman Kardons Exclusive Logic 7 andVMAx Modes

n MP3 Decoding for Use With Computersand Digital Audio Players

n Remote Automatically SetsOutput Levels for OptimumPerformance

n Front Panel Digital Inputs and CoaxDigital Output Capability for EasyConnection to Portable Digital Devicesand the Latest Video Game Consoles

n Multiple Digital Inputs and Outputs

n Front Panel Analog A/V and CoaxDigital Jacks Switchable to Outputs forEasy Connection to Portable DigitalDevices and Video Game Consoles

n On-Screen Menu and Display System

n 6-Channel Direct Input, Preamp Outputs and Main Amp Inputs for EasyExpansion and Use With Future AudioFormats

n Complete Multi-Zone System WithSeparate Zone II Remote Included

TM

CAUTIONRISK OF ELECTRIC SHOCK

DO NOT OPENCAUTION: To prevent electric shock,

do not use this (polarized) plug with an extension cord,

receptacle or other outlet unless the blades can

be fully inserted to prevent blade exposure.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products

enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

4 SAFETY INFORMATION

Safety Information

Important Safety Information

Verify Line Voltage Before UseYour AVR 510 has been designed for use with120-volt AC current. Connection to a line volt-age other than that for which it is intended can create a safety and fire hazard and maydamage the unit.

If you have any questions about the voltagerequirements for your specific model, or aboutthe line voltage in your area, contact your sellingdealer before plugging the unit into a wall outlet.

Do Not Use Extension CordsTo avoid safety hazards, use only the powercord attached to your unit. We do not recom-mend that extension cords be used with thisproduct. As with all electrical devices, do notrun power cords under rugs or carpets or placeheavy objects on them. Damaged power cordsshould be replaced immediately by an author-ized service depot with a cord meeting factoryspecifications.

Handle the AC Power Cord GentlyWhen disconnecting the power cord from anAC outlet, always pull the plug, never pull thecord. If you do not intend to use the unit forany considerable length of time, disconnect theplug from the AC outlet.

Do Not Open the CabinetThere are no user-serviceable componentsinside this product. Opening the cabinet maypresent a shock hazard, and any modificationto the product will void your guarantee. If wateror any metal object such as a paper clip, wireor a staple accidentally falls inside the unit, dis-connect it from the AC power source immedi-ately, and consult an authorized service station.

CATV or Antenna GroundingIf an outside antenna or cable system is con-nected to this product, be certain that it isgrounded so as to provide some protectionagainst voltage surges and static charges.Section 810 of the National Electrical Code,ANSI/NFPA No. 70-1984, provides informationwith respect to proper grounding of the mastand supporting structure, grounding of the lead-in wire to an antenna discharge unit, size ofgrounding conductors, location of antenna dis-charge unit, connection to grounding electrodesand requirements of the grounding electrode.

NOTE TO CATV SYSTEM INSTALLER: Thisreminder is provided to call the CATV (Cable

TV) system installers attention to article 820-40 of the NEC that provides guidelines forproper grounding and, in particular, specifiesthat the cable ground shall be connected to thegrounding system of the building, as close tothe point of cable entry as possible.

Installation Locationn To ensure proper operation and to avoid the

potential for safety hazards, place the uniton a firm and level surface. When placing theunit on a shelf, be certain that the shelf andany mounting hardware can support theweight of the product.

n Make certain that proper space is providedboth above and below the unit for ventila-tion. If this product will be installed in a cabinet or other enclosed area, make certainthat there is sufficient air movement withinthe cabinet. Under some circumstances a fanmay be required.

n Do not place the unit directly on a carpetedsurface.

n Avoid installation in extremely hot or coldlocations, or in an area that is exposed todirect sunlight or heating equipment.

n Avoid moist or humid locations.

n Do not obstruct the ventilation slots on thetop of the unit, or place objects directlyover them.

CleaningWhen the unit gets dirty, wipe it with a clean,soft, dry cloth. If necessary, wipe it with a softcloth dampened with mild soapy water, then afresh cloth with clean water. Wipe dry immedi-ately with a dry cloth. NEVER use benzene,aerosol cleaners, thinner, alcohol or any othervolatile cleaning agent. Do not use abrasivecleaners, as they may damage the finish of metalparts. Avoid spraying insecticide near the unit.

Moving the UnitBefore moving the unit, be certain to discon-nect any interconnection cords with other com-ponents, and make certain that you disconnectthe unit from the AC outlet.

Important Information for the UserThis equipment has been tested and found tocomply with the limits for a Class-B digitaldevice, pursuant to Part 15 of the FCC Rules.The limits are designed to provide reasonableprotection against harmful interference in aresidential installation. This equipment gener-ates, uses and can radiate radio-frequency energyand, if not installed and used in accordance

with the instructions, may cause harmful inter-ference to radio communication. However, thereis no guarantee that harmful interference willnot occur in a particular installation. If thisequipment does cause harmful interference toradio or television reception, which can bedetermined by turning the equipment off andon, the user is encouraged to try to correct theinterference by one or more of the followingmeasures:

n Reorient or relocate the receiving antenna.

n Increase the separation between the equip-ment and receiver.

n Connect the equipment into an outlet on acircuit different from that to which thereceiver is connected.

n Consult the dealer or an experiencedradio/TV technician for help.

This device complies with Part 15 of the FCCRules. Operation is subject to the following twoconditions: (1) this device may not cause harm-ful interference, and (2) this device must acceptinterference received, including interferencethat may cause undesired operation.

NOTE: Changes or modifications may causethis unit to fail to comply with Part 15 of theFCC Rules and may void the users authority tooperate the equipment.

Unpacking

The carton and shipping materials used to pro-tect your new receiver during shipment werespecially designed to cushion it from shock andvibration. We suggest that you save the cartonand packing materials for use in shipping if youmove, or should the unit ever need repair.

To minimize the size of the carton in storage,you may wish to flatten it. This is done by care-fully slitting the tape seams on the bottom andcollapsing the carton. Other cardboard insertsmay be stored in the same manner. Packingmaterials that cannot be collapsed should besaved along with the carton in a plastic bag.

If you do not wish to save the packaging mate-rials, please note that the carton and other sec-tions of the shipping protection are recyclable.Please respect the environment and discardthose materials at a local recycling center.

5 FRONT PANEL CONTROLS

1 Main Power Switch: Press this button toapply power to the AVR 510. When the switchis pressed in, the unit is placed in a Standbymode, as indicated by the amber PowerIndicator 3 surrounding the SystemPower Control 2. This button MUST bepressed in to operate the unit. To turn the unitoff and prevent the use of the remote control,this switch should be pressed until it pops outfrom the front panel so that the word OFFmay be read at the top of the switch.

NOTE: This switch is normally left in the ONposition.

2 System Power Control: When the MainPower Switch 1 is ON, press this buttonto turn on the AVR 510; press it again to turn

the unit off. Note that the Power Indicator3 surrounding the switch will turn greenwhen the unit is on.

3 Power Indicator: This LED will be lit inamber when the unit is in the Standby mode tosignal that the unit is ready to be turned on.When the unit is in operation, the indicator willturn green.

4 Headphone Jack: This jack may be used tolisten to the AVR 510s output through a pair ofheadphones. Be certain that the headphoneshave a standard 1/4" stereo phone plug. Notethat the main room speakers will automaticallybe turned off when the headphone jack is in use.

5 Selector Buttons: When you are establish-ing the AVR 510s configuration settings, usethese buttons to select from the choices available,as shown in the Main Information Display or the on-screen displays.

6 Tone Mode: Pressing this button enablesor disables the Bass and Treble tone controls.When the button is pressed so that the wordsTONE IN appear in the Main InformationDisplay , the settings of the Bass & andTreble ( controls may be used to adjust theoutput signals. When the button is pressed sothat the words TONE OUT appear in the MainInformation Display , the output signalwill be flat, without any bass or treble alter-ation, no matter how the actual Bass andTreble controls &( are adjusted.

Front Panel Controls

1 Main Power Switch2 System Power Control3 Power Indicator4 Headphone Jack5 Selector Buttons6 Tone Mode7 Surround Mode Selector8 Tuning Selector9 Tuner Band Selector) Preset Stations Selector

! Input Source Selector@ FM Mode Selector# Digital Optical 3 Input$ Input/Output Status Indicator% Digital Coax 3 Jack^ Video 4 Input Jacks& Bass Control* Balance Control( Treble Control Volume Control

Set Button Input Indicators Delay Digital Input Selector Main Information Display Channel Select Button Speaker Select Button Test Tone Selector Surround Mode Indicators Remote Sensor Window

&

&

*

&

(

333

111

444 555 666 777 888 999 ))) !!! @@@

### %%%

2930

$ ^^^

222

COAXIAL

THEATER5 CH STEREO HALL 123-STEREOPRO LOGICDIGITAL NIGHT MULTIOPTICAL ANALOG OSD

LFE

0 CL 0

1 2 3 1 2 3

MEMORY PRESETSLEEP

AUTO


MUTE TUNED ST O

ORO

O

LSO

ORSO

O

DTSDOLBY D

PCMMP3

6 FRONT PANEL CONTROLS

Front Panel Controls

7 Surround Mode Selector: Press this but-ton to change the surround mode by scrollingthrough the list of available modes. Note thatdepending on the type of input, some modesare not always available. (See page 27 for moreinformation about surround modes.)

8 Tuning Selector: Press the left side of thebutton to tune lower-frequency stations and theright side of the button to tune higher-frequencystations. When a station with a strong signal is reached, the TUNED indicator W will be litin the Main Information Display .

To tune manually, tap the button lightly andnote that the tuner will step up one frequencyincrement per button press. When the button isheld for a few seconds you will note that theunit will quickly search the frequency band.Release it once the fast tuning starts; the tunerwill automatically scan for the next station withan acceptable signal and then stop.

9 Tuner Band Selector: Pressing this buttonwill automatically switch the AVR 510 to theTuner mode. Pressing it again will switchbetween the AM and FM frequency bands. (Seepage 30 for more information on the tuner.)

) Preset Stations Selector: Press this button to scroll up or down through the list orstations that have been entered into the presetmemory. (See page 30 for more information ontuner programming.)

! Input Source Selector: Press this buttonto change the input by scrolling up or downthrough the list of input sources.

@ FM Mode Selector: Press this button toselect Auto or Manual tuning. When the buttonis pressed so that the AUTO indicator X lights,the tuner will search for the next station with anacceptable signal when the Tuning Selector8u is pressed. When the button ispressed so that the AUTO indicator X is not lit,each press of the Tuning Selector 8uwill increase the frequency. (See page 30 formore information on using the tuner.)

# Digital Optical 3 Input: Connect the opti-cal digital output of an audio or video product tothis jack. When the input is not in use, be certainto keep the plastic cap installed to avoid dustcontamination that might degrade future performance.

$ Input/Output Status Indicator: TheseLED indicators will normally light green to showthat the front panel Video 4 A/V jacks or theCoaxial 3 digital jack is operating as an input.When either of these jacks has been configuredfor use as an output, the indicator will turn redto show that the jack may be used for recording.(See page 20 for more information on configur-ing the front panel jacks as outputs, rather thaninputs.)

% Digital Coax 3 Jack: This jack is normallyused for connection to the output of portableaudio devices, video game consoles or otherproducts that have a coax digital jack. It mayalso be configured as an output jack, to feed adigital signal to a CD-R, MiniDisc or other digi-tal recording device. (See page 31 for informa-tion on configuring the Digital Coax 3 Jack toan output.)

^ Video 4 Input Jacks: These audio/videojacks may be used for temporary connection tovideo games or portable audio/video productssuch as camcorders and portable audio players.

& Bass Control: Turn this control to modifythe low-frequency output of the left/right chan-nels by as much as 10dB. Set this control to asuitable position for your taste or room acoustics.

* Balance Control: Turn this control tochange the relative volume for the frontleft/right channels.

NOTE: For proper operation of the surroundmodes this control should be at the midpoint,or 12 oclock, position.

( Treble Control: Turn this control to modifythe high-frequency output of the left/right chan-nels by as much as 10dB. Set this control to asuitable position for your taste or room acoustics.

Volume Control: Turn this knob clockwiseto increase the volume, counterclockwise todecrease the volume. If the AVR 510 is muted,adjusting volume control will automaticallyrelease the unit from the silenced condition.

Set Button: When making choices duringthe setup and configuration process, press thisbutton to enter the desired setting as shown in the Main Information Display into the AVR 510s memory.

Input Indicators: A green LED will light infront of the input that is currently being used asthe source for the AVR 510.

Delay: Press this button to begin thesequence of steps required to enter delay timesettings. (See page 21 for more information ondelay times.)

Digital Input Selector: When playing asource that has a digital output, press this button to select between the Optical #and Coaxial % Digital inputs. (Seepage 28 for more information on digital audio.)

Main Information Display: This displaydelivers messages and status indications tohelp you operate the receiver. (See pages 7 & 8for a complete explanation of the InformationDisplay.)

Channel Select Button: Press this buttonto begin the process of trimming the channeloutput levels using an external audio source.(For more information on output level trimadjustment, see page 31.)

Speaker Select Button: Press this buttonto begin the process of selecting the speakerpositions that are used in your listening room.(See page 22 for more information on setupand configuration.)

Test Tone Selector: Press this button tobegin the process of adjusting the channel out-put levels using the internal test tone as a ref-erence. (For more information on output leveladjustment, see page 23.)

Surround Mode Indicators: A green LEDwill light in front of the surround mode that iscurrently in use.

Remote Sensor Window: The sensorbehind this window receives infrared signalsfrom the remote control. Aim the remote at thisarea and do not block or cover it unless anexternal remote sensor is installed.

3231

7 FRONT PANEL INFORMATION DISPLAY

Front Panel Information Display

COAXIAL

THEATER5 CH STEREO HALL 123-STEREOPRO LOGICDIGITAL

DTSDOLBY D

PCMMP3

NIGHT MULTIOPTICAL ANALOG OSD

LFE

0 CL 0

1 2 3 1 2 3

MEMORY PRESETSLEEP

AUTO


MUTE TUNED ST

A

B

D E N OK ML

TU SR Q

P

Z Y X W V

F H I J

O

ORO

O

LSO

ORSO

O

C G

A Bitstream IndicatorsB Optical Source IndicatorsC DTS Mode IndicatorD Dolby Digital IndicatorE Coaxial Source IndicatorsF Dolby Pro Logic IndicatorG Analog Input IndicatorH Dolby 3 Stereo IndicatorI VMAx Mode Indicator

J 5-Channel Stereo IndicatorK Logic 7 Mode IndicatorsL Hall Mode IndicatorsM OSD IndicatorN Theater Mode IndicatorO Night Mode IndicatorP Multiroom IndicatorQ Speaker/Channel Input IndicatorsR Preset Number/Sleep Timer

S Preset IndicatorT Sleep IndicatorU Memory IndicatorV Stereo IndicatorW Tuned IndicatorX Auto IndicatorY Main Information DisplayZ Mute Indicator

A Bitstream Indicators: When the input is adigital source, one of these indicators will light todisplay the specific type of data signal in use.

B Optical Source Indicators: These indica-tors light to show when an Optical Digital Inputhas been selected.

C DTS Mode Indicator: This indicator lightswhen a DTS-encoded source is playing.

D Dolby Digital Indicator: This indicatorlights when a Dolby Digital source is beingplayed.

E Coaxial Source Indicators: These indica-tors light to show when a Coaxial Digital Inputhas been selected.

F Dolby Pro Logic Indicator: This indicatorlights when the Dolby Pro Logic mode has beenselected.

G Analog Input Indicator: This indicatorlights when an analog input source has beenselected.

H Dolby 3 Stereo Indicator: This indicatorlights when the Dolby 3 Stereo Mode has beenselected.

I VMAx Mode Indicator: This indicatorlights when the VMAx mode is in use.VMAx F appears when the Far Field VMAxmode is selected; VMAx N appears when theNear Field VMAx mode is selected. (See page27 for a description of the VMAx modes.)

J 5-Channel Stereo Indicator: This indica-tor lights when the 5-Channel Stereo mode hasbeen selected.

K Logic 7 Mode Indicators: These indica-tors light when the Logic 7 mode is in use.LOGIC 7C appears for the Cinema versionof Logic 7, LOGIC 7M appears for theMusic version of Logic 7. (See page 27 for adescription of the Logic 7 Modes.)

L Hall Mode Indicators: These indicatorslight when one of the Hall modes has beenselected.

M OSD Indicator: When the OSD system is inuse, this indicator lights to remind you that theother indicators in this display do not functionwhen the On Screen Display is being used.

N Theater Mode Indicator: This indicatorlights to show that the Theater mode is in use.

O Night Mode Indicator: This indicatorlights when the AVR 510 is in the Night mode,which preserves the dynamic range of digitalprogram material at low volume levels.

P Multiroom Indicator: This indicator lightswhen the multiroom system is active. Note thatit will remain lit when the multiroom system isin use even though the main room system is inthe Standby mode and all other indicators aredark. (See page 35 for more information on theMultiroom system.)

Q Speaker/Channel Input Indicators: Theseindicators are multipurpose, indicating either thespeaker type selected for each channel or theincoming data-signal configuration. The left,center, right, right surround and left surround speaker indicators are composed of three boxes,while the subwoofer is a single box. The centerbox lights when a Small speaker is selected,and the two outer boxes light when Largespeakers are selected. When none of the boxesare lit for the center, surround or subwooferchannels, no speaker has been selected for oneof those positions. (See page 22 for more infor-mation on configuring speakers.) The lettersinside each of the center boxes display the activeinput channels. For standard analog inputs, onlythe L and R will light, indicating a stereo input.When a digital source is playing, the indicatorswill light to display the channels being receivedat the digital input. When the letters flash, thedigital input has been interrupted. (See pages 23& 29 for more information on the ChannelIndicators.)

R Preset Number/Sleep Timer: When thetuner is in use, these numbers indicate the spe-cific preset memory location in use. (See page31 for more information on preset stations.)When the Sleep function is in use, these num-bers show how many minutes remain beforethe unit goes into the Standby mode.

8 FRONT PANEL INFORMATION DISPLAY

Front Panel Information Display

S Preset Indicator: This indicator lights whenthe tuner is in use to show that the PresetNumber/Sleep Timer R is showing the sta-tions preset memory number. (See page 31 formore information on tuner presets.)

T Sleep Indicator: This indicator lights whenthe Sleep function is in use. The numbers in thePreset Number/Sleep Timer indicator willshow the minutes remaining before the AVR 510goes into the Standby mode. (See page 26 formore information on the Sleep function.)

U Memory Indicator: This indicator flasheswhen entering presets and other informationinto the tuners memory.

V Stereo Indicator: This indicator lights whenan FM station is being tuned in stereo.

W Tuned Indicator: This indicator lights when astation is being received with sufficient signalstrength to provide acceptable listening quality.

X Auto Indicator: This indicator lights whenthe tuners Auto mode is in use.

Y Main Information Display: This displayshows messages relating to the status, inputsource, surround mode, tuner, volume level orother aspects of the AVR 510s operation.

Z Mute Indicator: This indicator lights toremind you that the AVR 510s output has beensilenced by pressing the Mute button .Press the Mute button again to return to thepreviously selected output level.

38

9 REAR PANEL CONNECTIONS

Rear Panel Connections

a

b

c

d

e

f

gi

j

`

31

3236

h

k

35

34

33

HDCD, High Definitioni Compatible Digital and Pacific Microsonics areeither registered trademarks or trademarks of Pacific Microsonics, Inc. In the UnitedStates and/or other countries. HDCD system manufactured under license from PacificMicrosonics, Inc. This product is covered by one or more of the following: in the USA:5,479,168, 5,638,074, 5,640,161, 5,808,574, 5,838,274, 5,854,600, 5,864,311,5,872,531, and in Australia: 669114. Other patents pending.

` Tape Inputs Tape Outputs Video 1 Audio Inputs AM Antenna Video 1 Audio Outputs DVD Audio Inputs FM Antenna CD Inputs 6-Channel Direct Inputs Multiroom Outputs Amplifier Inputs Preamp Outputs Subwoofer Output Video Monitor Outputs

Speaker Outputs Switched AC Accessory Outlet Unswitched AC Accessory Outlet AC Power Cord Component Video Outputsa Video 2 Component Video Inputsb DVD Component Video Inputsc Remote IR Outputd Remote IR Inpute Multiroom IR Inputf DVD Video Inputsg Video 1 Video Outputsh Video 3 Video Inputsi Video 2 Video Inputs

j Video 2 Video Outputsk Video 1 Video Inputs

Optical Digital InputsCoaxial Digital InputsDigital Audio OutputsVideo 3 Audio InputsVideo 2 Audio InputsVIdeo 2 Audio Outputs36

3534333231

10 REAR PANEL CONNECTIONS

Rear Panel Connections

` Tape Inputs: Connect these jacks to thePLAY/OUT jacks of an audio recorder.

Tape Outputs: Connect these jacks to theRECORD/INPUT jacks of an audio recorder.

Video 1 Audio Inputs: Connect thesejacks to the PLAY/OUT audio jacks on a VCRor other video source.

AM Antenna: Connect the AM loop antennasupplied with the receiver to these terminals. If anexternal AM antenna is used, make connectionsto the AM and GND terminals in accordancewith the instructions supplied with the antenna.

Video 1 Audio Outputs: Connect thesejacks to the RECORD/INPUT audio jacks on a VCR.

DVD Audio Inputs: Connect these jacksto the analog audio jacks on a DVD or othervideo source.

FM Antenna: Connect the supplied indoor oran optional external FM antenna to this terminal.

CD Inputs: Connect these jacks to the out-put of a compact disc player or CD changer.

6-Channel Direct Inputs: If an externaldigital audio decoder is used, connect the out-puts of that decoder to these jacks.

Multiroom Outputs: Connect these jacksto an optional audio power amplifier to listento the source selected by the mulitroom systemin a remote room.

Amplifier Inputs: When the jumper pinsthat link the Preamp Outputs with theseinputs are removed, these jacks may be used toconnect an external source or the AVR 510smultiroom system to the internal amplifiers.(See page 17 for more information on usingthese connections.)

Preamp Outputs: When the jumper pinsthat link the Amplifier Inputs with theseoutputs are removed, these jacks may be con-nected to an external power amplifier.

Subwoofer Output: Connect this jack tothe line-level input of a powered subwoofer. Ifan external subwoofer amplifier is used, con-nect this jack to the subwoofer amplifier input.

Video Monitor Outputs: Connect thisjack to the composite or S-Video input of a TVmonitor or video projector to view the on-screen

menus and the output of any standard videosource selected by the receivers video switcher.

Speaker Outputs: Connect these outputsto the matching + or terminals on your leftand right surround speakers. When makingspeaker connections always make certain tomaintain correct polarity by connecting the red(+) terminals on the AVR 510 to the red (+) ter-minals on the speakers and the black () termi-nals on the AVR 510 to the black () terminalson the speakers. See page 15 for more informa-tion on speaker polarity.

Switched AC Accessory Outlet: This outlet may be used to power any device youwish to have turned on when the AVR 510 isturned on with the System Power Controlbutton 2.

Unswitched AC Accessory Outlet: Thisoutlet may be used to power any AC device.The power will remain on at this outlet regard-less of whether the AVR 510 is on or off.

Note: The total power consumption of alldevices connected to the accessory outletsshould not exceed 100 watts.

AC Power Cord: Connect the AC plug toan unswitched AC wall output.

Component Video Outputs: Connectthese outputs to the component video inputs ofa video projector or monitor. When a sourceconnected to one of the two ComponentVideo Inputs ab is selected the signal willbe sent to these jacks.

a Video 2 Component Video Inputs:Connect the Y/Pr/Pb component video outputsof a set top converter box or other video prod-uct to these jacks.

b DVD Component Video Inputs: Connectthe Y/Pr/Pb component video outputs of a DVDplayer to these jacks.

c Remote IR Output: This connection per-mits the IR sensor in the receiver to serve otherremote controlled devices. Connect this jack tothe IR IN jack on Harman Kardon (or othercompatible) equipment.

d Remote IR Input: If the AVR 510s front-panel IR sensor is blocked due to cabinetdoors or other obstructions, an external IRsensor may be used. Connect the output ofthe sensor to this jack.

e Multiroom IR Input: Connect the output ofan IR sensor in a remote room to this jack tooperate the AVR 510s multiroom control system.

f DVD Video Inputs: Connect these jacks tothe composite or S-Video output jacks on aDVD or other video source.

g Video 1 Video Outputs: Connect thesejacks to the RECORD/INPUT composite or S-Video jack on a VCR.

h Video 3 Video Inputs: Connect thesejacks to the PLAY/OUT composite or S-Videojacks on a VCR or other video source.

i Video 2 Video Inputs: Connect thesejacks to the PLAY/OUT composite or S-Videojacks on a VCR or other video source.

j Video 2 Video Outputs: Connect thesejacks to the RECORD/INPUT composite or S-Video jacks on a VCR.

k Video 1 Video Inputs: Connect thesejacks to the PLAY/OUT composite or S-Videojacks on a VCR or other video source.

Optical Digital Inputs: Connect the opti-cal digital output from a DVD player, HDTVreceiver, LD player or CD player to these jacks.The signal may be either a Dolby Digital signal,a DTS signal or a standard PCM digital source.

Coaxial Digital Inputs: Connect the coaxdigital output from a DVD player, HDTV receiver,LD player or CD player to these jacks. The signalmay be either a Dolby Digital signal, DTS signalor a standard PCM digital source. Do not con-nect the RF digital output of an LD player tothese jacks.

Digital Audio Outputs: Connect thesejacks to the matching digital input connectoron a digital recorder such as a CD-R orMiniDisc recorder.



Video 2 Audio Outputs: Connect thesejacks to the RECORD/INPUT audio jacks on aVCR or other video source.

36

35

34

33

32

31

11 MAIN REMOTE CONTROL FUNCTIONS

l

l

l

l

l

l

l

l

l

l

l

l

l

Main Remote Control Functions

POWER

MUTE

AVR

AM/FM

VCR

6 CH.

OFF ON

SLEEPT/V

SURR.M-ROOMCH.

GUID

E

CH.

EXITDIGITAL

MENUSPKR

PREV

.CH.DE

LAY

SET

TUN-M MEM

D.SKIPOSD

DIRECT

TUNING PRESET

CLEAR

DWN UP

TEST

NIGHT

510

SKIP

abc

de

f

gh

ij

kl

mn

po

q

n

s

r

t

u

vw

32

30

29

DVD CD TAPE

VID 2TV CBL/SAT

VID 4VID 1 VID 3

SPLLEARN

1 2 3 4

765

9 0

8

M2 M3 M4M1

28

VOL.

3736

35

34

33

31

38

z

x

y

39

40

TM

LIGHT

a Power On Buttonb IR Transmitter Windowc Program/SPL Indicatord Power Off Buttone Input Selectorsf AVR Selectorg AM/FM Tuner Selecth Learn Buttoni Test Buttonj Sleep Buttonk Surround Mode Selectorl Night Modem Channel Select Buttonn / Buttonso Buttonp Set Buttonq Digital Selectr Numeric Keyss Tuner Modet Direct Buttonu Tuning Up/Downv OSD Buttonw Macro Buttonsx Transport Controlsy Skip Up/Down Buttonsz Disc Skip Buttons Preset Up/Down28 Clear Button29 Memory Button30 Delay/Prev. Ch.31 Button32 Speaker Select33 Multiroom34 Volume Up/Down35 TV/Video Selector36 SPL Indicator Select37 6-Channel Direct Input38 Mute39 EzSet Sensor Microphone40 Light Button

NOTE: The function names shown here are eachbuttons feature when used with the AVR 510.Most buttons have additional functions whenused with other devices. See pages 4142 for alist of these functions.



IMPORTANT NOTE: The AVR 510s remotemay be programmed to control up to eightdevices, including the AVR 510. Before using theremote, it is important to remember to press theInput Selector button e that corresponds tothe unit you wish to operate. In addition, theAVR 510s remote is shipped from the factory tooperate the AVR 510 and most Harman KardonCD or DVD players and cassette decks. Theremote is also capable of operating a wide vari-ety of other products using the control codesthat are part of the remote. Before using theremote with other products, follow the instruc-tions on pages 3640 to program the propercodes for the products in your system.

It is also important to remember that many ofthe buttons on the remote take on differentfunctions, depending on the product selectedusing the Device Control Selectors. The descrip-tions shown here primarily detail the functionsof the remote when it is used to operate theAVR 510. (See page 40 for information aboutalternate functions for the remotes buttons.)

a Power On Button: Press this button toturn on the power to a device selected by press-ing one of the Input Selectors e.

b IR Transmitter Window: Point this win-dow towards the AVR 510 when pressing buttonson the remote to make certain that infrared com-mands are properly received.

c Program/SPL Indicator: This three-colorindicator is used to guide you through theprocess of programming the remote or learningcommands from a remote into the AVR 510sremote code memory and it is also used as alevel indicator when using the remotes EzSetcapabilities. (See page 23 for more informationon setting output levels, and see page 36 forinformation on programming the remote.)

d Power Off Button: Press this button toplace the AVR 510 or a selected device in theStandby mode. Note that this will turn off themain room functions, but if the Multiroom sys-tem is activated, it will continue to function.

e Input Selectors: Pressing one of thesebuttons will perform three actions at the sametime. First, if the AVR 510 is not turned on, thiswill power up the unit. Next, it will select thesource shown on the button as the input to theAVR 510. Finally, it will change the remote con-trol so that it controls the device selected. Afterpressing one of these buttons you must pressthe AVR Selector button f again to oper-ate the AVR 510s functions with the remote.

f AVR Selector: Pressing this button willswitch the remote so that it will operate theAVR 510s functions. If the AVR 510 is in theStandby mode, it will also turn the AVR 510 on.

g AM/FM Tuner Select: Press this button toselect the AVR 510s tuner as the listeningchoice. Pressing this button when the tuner isalready in use will select between the AM andFM bands.

h Learn Button: Press this button to beginthe process of learning the codes from anotherproducts remote into the AVR 510s remote. (Seepage 37 for more information on using theremotes learning function.)

i Test Button: Press this button to beginthe sequence used to calibrate the AVR 510soutput levels. (See page 23 for more informationon calibrating the AVR 510.)

j Sleep Button: Press this button to placethe unit in the Sleep mode. After the timeshown in the display, the AVR 510 will auto-matically go into the Standby mode. Each pressof the button changes the time until turn-off inthe following order:

Note that this button is also used to changechannels on your TV when the TV is selected.

When the AVR 510 remote is being programmedwith the codes to operate another device, thisbutton is also used in the Auto Search process.(See page 36 for more information on program-ming the remote.)

k Surround Mode Selector: Press thisbutton to begin the process of changingthe surround mode. After the button hasbeen pressed, use the / buttons n toselect the desired surround mode. (See page 28for more information.) Note that this button isalso used to tune channels when the TV isselected using the device Input Selectore. When the AVR 510 remote is being pro-grammed with the codes of another device, thisbutton is also used in the Auto Searchprocess. (See page 36 for more information onprogramming the remote.)

l Night Mode: Press this button to activatethe Night mode. This mode is available in spe-cially encoded digital sources, and it preserves

dialog (center channel) intelligibility at low volume levels.

m Channel Select Button: This button isused to start the process of setting the AVR 510soutput levels to an external source. Once this but-ton is pressed, use the / buttons n toselect the channel being adjusted, then press theSet button p, followed by the / buttonsagain, to change the level setting. (See page 31for more information.)

n / Buttons: These are multi-purposebuttons. They will be used most frequently toselect a surround mode. To change the surroundmode, first press the Surround Mode selectork. Next press these buttons to scroll up ordown through the list of surround modes thatappear in the Main Information Display 25..These buttons are also used to increase ordecrease output levels when configuring theunit with either the internal test tone or anexternal source. They are also used to enterdelay time settings after the Delay buttonhas been pressed.

o Button: This button is used to changethe menu selection or setting during some ofthe setup procedures for the AVR 510.

p Set Button: This button is used to entersettings into the AVR 510s memory. It is alsoused in the setup procedures for delay time,speaker configuration and channel output leveladjustment.

q Digital Select: Press this button to assignone of the digital inputs # % to a source.(See page 28 for more information on usingdigital inputs.)

r Numeric Keys: These buttons serve as aten-button numeric keypad to enter tuner presetpositions. They are also used to select channelnumbers when TV has been selected on theremote, or to select track numbers on a CD,DVD or LD player, depending on how theremote has been programmed.

s Tuner Mode: Press this button when thetuner is in use to select between automatic tuning and manual tuning. When the button ispressed so that the AUTO indicator X goesout, pressing the Tuning buttons u8will move the frequency up or down in single-step increments. When the FM band is in use,pressing this button when a stations signal isweak will change to monaural reception. (Seepage 30 for more information.)

30

90min

80min

70min

60min

50min

40min

30min

20min

10min OFF


t Direct Button: Press this button whenthe tuner is in use to start the sequence fordirect entry of a stations frequency. After press-ing the button, simply press the properNumeric Keys r to select a station. (Seepage 30 for more information on the tuner.)

u Tuning Up/Down: When the tuner is inuse, these buttons will tune up or down throughthe selected frequency band. If the Tuner Modebutton s@ has been pressed so that theAUTO indicator X is illuminated, pressing andholding either of the buttons for three secondswill cause the tuner to seek the next station withacceptable signal strength for quality reception.When the AUTO indicator X is NOT illumi-nated, pressing these buttons will tune stationsin single-step increments. (See page 30 for moreinformation.)

v OSD Button: Press this button to activatethe On Screen Display (OSD) system used to setup or adjust the AVR 510s parameters.

w Macro Buttons: Press these buttons to store or recall a Macro, which is a preprogrammed sequence of commands stored in the remote. (See page 37 for moreinformation on storing and recalling macros.)

x Transport Controls: These buttons donot have any functions for the AVR 510, butthey may be programmed for the forward/reverse play operation of a wide variety of CDor DVD players, and audio or video cassetterecorders. (See page 38 for more information.)

y Skip Up/Down Buttons: These buttonsdo not have a direct function with the AVR 510,but when used with a compatibly programmedCD or DVD changer they will change the disccurrently being played in the changer.

z Disc Skip Buttons: These buttons haveno direct function for the AVR 510, but they areoften used when the remote is programmed tooperate a CD or DVD changer to change thediscs in the changer. (See page 38 for moreinformation on using the remote with otherdevices.)

Preset Up/Down: When the tuner is in use, press these buttons to scroll through the stations programmed into the AVR 510s mem-

ory. When some source devices, such as CDplayers, VCRs and cassette decks, are selectedusing the device Input Selectors e, thesebuttons may function as Chapter Step or TrackAdvance.

Clear Button: Press this button to clearincorrect entries when using the remote to directly enter a radio stations frequency.

Memory Button: Press this button toenter a radio station into the AVR 510s presetmemory. Once the MEMORY indicator Uflashes, you have five seconds to enter a presetmemory location using the Numeric Keysr. (See page 31 for more information.)

Delay/Prev Ch.: Press this button tobegin the process for setting the delay timesused by the AVR 510 when processing surroundsound. After pressing this button, the delaytimes are entered by pressing the Set buttonp and then using the / buttons n tochange the setting. Press the Set button pagain to complete the process. (See page 21 formore information.)

Button: Press this button to change asetting or selection when configuring many of theAVR 510s settings.

Speaker Select: Press this button to begin the process of configuring the AVR 510s bass management system for usewith the type of speakers used in your system.Once the button has been pressed, use the/ buttons n to select the channel youwish to set up. Press the Set button p andthen select another channel to configure.When all adjustments have been completed,press the Set button p twice to exit the settings and return to normal operation. (Seepage 22 for more information.)

Multiroom: Press this button to activatethe multiroom system or to begin the process ofchanging the input or volume level for the sec-ond zone. (See page 35 for more information onthe multiroom system.)

Volume Up/Down: Press these buttons toraise or lower the system volume.

TV/Video Button: This button does nothave a direct function on the AVR 510, butwhen used with a compatibly programmedVCR, DVD or satellite receiver that has aTV/Video function, pressing this button willswitch between the output of the player orreceiver and the external video input to thatplayer. Consult the Owners Manual for yourspecific player or receiver for the details of howit implements this function.

SPL Indicator Select: This button acti-vates the AVR 510s EzSet function to quicklyand accurately calibrate the AVR 510s outputlevels. Press and hold the button for three sec-onds and then release it. Note that the testtone will begin circulating, and theProgram/SPL Indicator c will change col-ors. During this sequence, EzSet will automati-cally adjust the output levels for all channelsuntil they are equal, as shown by theProgram/SPL Indicator lighting green foreach channel. Press this button again when theadjustment is complete to turn off the testtone. (See page 23 for more information onEzSet.)

6-Ch. Direct Input: Press this button to select the component connected to the 6-Channel Direct Input as the source.

Mute: Press this button to momentarilysilence the AVR 510 or TV set being controlled,depending on which device has been selected.When the AVR 510 remote is being programmedto operate another device, this button is pressedwith the Input Selector button e to beginthe programming process. (See page 36 formore information on programming the remote.)

EzSet Sensor Microphone: The sensormicrophone for the EzSet microphone is behindthese slots. When using the remote to calibratespeaker output levels using EzSet, be sure thatyou do not hold the remote in a way that cov-ers these slots. (See page 23 for more informa-tion on using EzSet.)

Light Button: Press this button to acti-vate the remotes backlight for ease of use indarkened rooms.

40

39

38

37

36

35

34

33

32

31

30

29

28


14 ZONE II REMOTE CONTROL FUNCTIONS

Zone II Remote Control Functions

Power Off AVR Selector AM/FM Tuner Select Input Selectors Tuning Up/Down Fast Play Record/Pause' Preset/Track Skip Disc Skip

Volume Up/Down Play Forward/Reverse/Stop Mute

NOTE: The Zone II remote may be used ineither the same room where the AVR 510 islocated, or it may be used in a separate roomwith an optional infrared sensor that is con-nected to the AVR 510s Multiroom IR Inputjack e. When it is used in the same room asthe AVR 510, it will control the functions of theAVR 510 or any compatible Harman Kardonproducts in that room. When it is used in a sep-arate room via a sensor connected to theMultiroom IR jack e, the buttons for power,

input source, volume and mute will control thesource and volume for the second zone, as con-nected to the Multiroom Out jacks . (Seepage 35 for complete information on using theMultiroom system.)

I

Power Off: When used in the roomwhere the AVR 510 is located, press this buttonto place the unit in Standby. When it is used ina remote room with a sensor that is connectedto the Multi IR jack e, this button turns theMultiroom system on and off.

AVR Selector: Press this button to turnon the AVR 510. The input in use when the unitwas last on will be selected.

AM/FM Tuner Select: Press this buttonto select the Tuner as the input to theMultiroom system. Press it again to changebetween the AM and FM bands.

Input Selectors: When the AVR 510 isoff, press one of these buttons to select a spe-cific input and turn the unit on. When the unitis already in use, pressing one of these buttonswill change the input.

Tuning Up/Down Fast Play: Whenthis remote is used in the same room as theAVR 510, these buttons may be used to changethe frequency of the tuner. These buttons mayalso control the Fast Play or Fast Reverse func-tions of compatible Harman Kardon CD, DVD orcassette decks in the same room, or from aremote room when an IR link is connected tothe AVR 510.

Record/Pause: Press this button to acti-vate the Record or Pause function on compati-ble Harman Kardon CD, DVD or Cassette Deckproducts.

' Preset Up/Down Track Skip: Whenthe AVR 510s tuner is selected as the inputsource, these buttons will move up or downthrough the list of stations that have beenstored in the preset memory. When a CD orDVD player is selected, these buttons activatethe Forward or Reverse Track or Chapter Skipfunctions.

Disc Skip: Press this button to changediscs on compatible Harman Kardon CD or DVDplayers.

Volume Up/Down: When used in theroom where the AVR 510 is located, press thisbutton to raise or lower the volume in thatroom. When it is used in a remote room with asensor that is connected to the Multiroom IRjack e, this button will raise or lower the vol-ume in the remote room.

Play Forward/Reverse/Stop: Pressthese buttons to control compatibleHarman Kardon CD, DVD or cassette players.

Mute: When used in the room where theAVR 510 is located, press this button to tem-porarily silence the unit. When it is used in aremote room with a sensor that is connected tothe Multiroom IR jack e, this button willtemporarily silence the feed to the remote roomonly. Press the button again to return to theprevious volume level.

I

POWER

OFF

MUTE

AVR

AM//FM

VID 1

VID 3

DVD CD TAPE

DN TUNING

PRESET

VOLUME

DISC SKIP

DISC SKIP

UPDN

UP

VID 4

VID 2

G

A

B

C

D

E

F

H

I

K

J

System InstallationAfter unpacking the unit, and placing it on a solidsurface capable of supporting its weight, you willneed to make the connections to your audio andvideo equipment.

Audio Equipment ConnectionsWe recommend that you use high-quality inter-connect cables when making connections tosource equipment and recorders to preserve theintegrity of the signals.

When making connections to audio sourceequipment or speakers, it is always a goodpractice to unplug the unit from the AC walloutlet. This prevents any possibility of acciden-tally sending audio or transient signals to thespeakers that may damage them.

1. Connect the analog output of a CD player tothe CD inputs .

NOTE: When the CD player has both fixed andvariable audio outputs, it is best to use thefixed output unless you find that the input tothe receiver is so low that the sound is noisy, orso high that the signal is distorted.

2. Connect the analog Play/Out jacks of a cas-sette deck, MD, CD-R or other audio recorder tothe Tape Input jacks `. Connect the analogRecord/In jacks on the recorder to the TapeOutput jacks on the AVR 510.

3. Connect the output of any digital sources to the appropriate input connections on theAVR 510 rear panel. Note that the Opticaland Coaxial digital inputs #% maybe used with a Dolby Digital or DTS source orthe output of a conventional CD or LD playersPCM (S/P-DIF) output.

4. Connect the coaxial or optical Digital AudioOutputs on the rear panel of the AVR 510 tothe matching digital input connections on a CD-Ror MiniDisc recorder.

5. Assemble the AM Loop Antenna suppliedwith the unit as shown below. Connect it to theAM and GND screw terminals .

6. Connect the supplied FM antenna to the FM(75-ohm) connection . The FM antenna maybe an external roof antenna, an inside poweredor wire-lead antenna or a connection from acable TV system. Note that if the antenna orconnection uses 300-ohm twin-lead cable, youmust use the 300-ohm-to-75-ohm adapter sup-plied with the unit to make the connection.

7. Connect the front, center and surround speaker outputs to the respective speakers.

To ensure that all the audio signals are carriedto your speakers without loss of clarity or reso-lution, we suggest that you use high-qualityspeaker cable. Many brands of cable are avail-able and the choice of cable may be influencedby the distance between your speakers and thereceiver, the type of speakers you use, personalpreferences and other factors. Your dealer orinstaller is a valuable resource to consult inselecting the proper cable.

Regardless of the brand of cable selected, werecommend that you use a cable constructed offine, multistrand copper with a gauge of 14 orsmaller. Remember that in specifying cable, thelower the number, the thicker the cable.

Cable with a gauge of 16 may be used for shortruns of less than ten feet. We do not recom-mend that you use cables with an AWG equiva-lent of 18 or higher, due to the power loss anddegradation in performance that will occur.

Cables that are run inside walls should have theappropriate markings to indicate listing with UL,CSA or other appropriate testing agency stan-dards. Questions about running cables insidewalls should be referred to your installer or alicensed electrical contractor who is familiarwith the NEC and/or the applicable local build-ing codes in your area.

When connecting wires to the speakers, be cer-tain to observe proper polarity. Remember toconnect the negative or black wire to thesame terminal on both the receiver and thespeaker. Similarly, the positive or red wireshould be connected to like terminals on theAVR 510 and speaker.

NOTE: While most speaker manufacturersadhere to an industry convention of using blackterminals for negative and red ones for positive,some manufacturers may vary from this config-

uration. To ensure proper phase and optimalperformance, consult the identification plate onyour speaker or the speakers manual to verifypolarity. If you do not know the polarity of yourspeaker, ask your dealer for advice before pro-ceeding, or consult the speakers manufacturer.

We also recommend that the length of cableused to connect speaker pairs be identical.For example, use the same length piece ofcable to connect the front-left and front-rightor surround-left and surround-right speakers,even if the speakers are a different distancefrom the AVR 510.

8. Connections to a subwoofer are normallymade via a line-level audio connection from theSubwoofer Output to the line-level inputof a subwoofer with a built-in amplifier. When apassive subwoofer is used, the connection firstgoes to a power amplifier, which will be con-nected to one or more subwoofer speakers. Ifyou are using a powered subwoofer that doesnot have line-level input connections, follow theinstructions furnished with the speaker for con-nection information.

33

3231

15 INSTALLATION AND CONNECTIONS

Installation and Connections



Video Equipment ConnectionsVideo equipment is connected in the same man-ner as audio components. Again, the use of high-quality interconnect cables is recommended topreserve signal quality.

1. Connect a VCRs or other video sourcesaudio and video Play/Out jacks to the Video 1or Video 2 In jacks ik on the rearpanel. The Audio and Video Record/In jacks onthe VCR should be connected to the Video 1or Video 2 Out jacks gj on theAVR 510.

2. Connect the analog audio and video outputsof a satellite receiver, cable TV converter or television set or any other video source to theVideo 3 h jacks.

3. Connect the analog audio and video outputs of a DVD or laser disc player to theDVD jacks f.

4. Connect the digital audio outputs of a DVDplayer, satellite receiver, cable box or HDTV con-verter to the appropriate Optical or CoaxialDigital Inputs #%.

5. Connect the Video Monitor Output jacks on the receiver to the composite or S-Video input of your television monitor orvideo projector.

6. If your DVD player and monitor both havecomponent video connections, connect thecomponent outputs of the DVD player to theDVD Component Video Inputs b. Notethat even when component video connectionsare used, the audio connections should still bemade to either the analog DVD Audio Inputs or any of the Optical or Coaxial DigitalInput jacks .

7. If another component video device is avail-able, connect it to the Video 2 ComponentVideo Input jacks a. The audio connectionsfor this device should be made to either theVideo 2 Audio Input jacks or any of theOptical or Coaxial Digital Input jacks

.

8. If the component video inputs are used, con-nect the Component Video Output tothe component video inputs of your TV, projec-tor or display device.

Video Connection Notes: When the component video jacks are used,

the on-screen menus will not be visible. Youmust switch to the standard composite or S-Video input on your TV to view thosemenus.

The AVR 510s component video system isdesigned for standard video rate (NTSC/480i)video from DVD players and similar devices.While it will operate with high-definition signals, or progressive-scan DVD players, thequality may be slightly less than with a directconnection.

The AVR 510 will accept either standardcomposite, S-Video or Y/Pr/Pb componentvideo signals. However, it will not convertcomposite or S signals to component video.

Component or composite video signals mayonly be viewed in their native formats.However, S-Video signals will be converted tostandard, composite video, and are viewablethrough the composite Video MonitorOutput .

System and Power Connections

The AVR 510 is designed for flexible use withmultiroom systems, external control compo-nents and power amplifiers.

Main Room Remote Control ExtensionIf the receiver is placed behind a solid orsmoked glass cabinet door, the obstruction mayprevent the remote sensor from receiving com-mands. In this event, an optional remote sensormay be used. Connect the output of the remotesensor to the Remote IR Input jack d.

If other components are also prevented fromreceiving remote commands, only one sensor isneeded. Simply use this units sensor or aremote eye by running a connection from theRemote IR Output jack c to the Remote IR Input jack on Harman Kardon or other com-patible equipment.

Multiroom IR LinkThe remote room IR receiver should be connectedto the AVR 510 via standard coaxial cable. Plugthe IR connection cable into the Multiroom IRInput jack e on the AVR 510s rear panel.

If other Harman Kardon compatible sourceequipment is part of the main room installation,the Remote IR Output jack c on the rear

panel should be connected to the IR IN jack on source equipment. This will enable the remoteroom location to control source equipment functions.

NOTE: All remotely controlled componentsmust be linked together in a daisy chain.Connect the IR OUT jack of one unit to the IR IN of the next to establish this chain.

Multiroom Audio ConnectionsDepending on the distance from the AVR 510to the remote room, two options are availablefor audio connection:

Option 1: Use high-quality, shielded audiointerconnect cable from the AVR 510s locationto the remote room. In the remote room, con-nect the interconnect cable to a stereo poweramplifier. The amplifier will be connected to therooms speakers. No volume control is required,as the AVR 510 and the remote IR link will pro-vide that function. At the AVR 510, plug theaudio interconnect cables into the MultiroomOutput jacks on the AVR 510s rear panel.

NOTE: The remote power amplifier must have signal-sensing capability or be left on constantly toensure automatic operation in the remote room.

Option 2: Place the amplifier that will providepower to the remote location speakers in thesame room as the AVR 510, and connect theMultiroom Output jacks on the rearpanel of the AVR 510 to the audio input of theremote room amplifier. Use the appropriatespeaker wire to connect the optional poweramplifier to the remote speakers. High-qualitywire of at least AWG14 is recommended forlong multiroom connections.

3231

35

3231

3231

34

36

35



IMPORTANT NOTE: Any cables run inside wallsshould be CL3/FT4-rated or carry any other certi-fication that is required by the NEC or state andlocal building and electrical codes. To avoid inter-ference, audio and speaker cables should not beparallel to, or run in the same conduits or pathwith, AC cables. If you have any questions aboutmultiroom wiring, consult your dealer, custominstaller or low-voltage electrical contractor.

External Audio Power AmplifierConnectionsIf desired, the AVR 510 may be connected tooptional, external audio power amplifiers orused with equalizers or speaker systems thatrequire connection between the preamp andamplifier sections of a receiver.

To make these connections, remove the jumpersthat connect the Preamp Out jacks andAmplifier In jacks for the channels to beused with external devices. Store the jumpers ina safe place so that the AVR 510 may be usedin its normal mode at a future date, if desired.

When an external amplifier is used, connect thePreamp Out jacks to the inputs on theamplifier. When an equalizer or speaker proces-sor is used, connect the Preamp Out jacks to the inputs of the processor, and connect theoutputs of the processor back to the AmplifierIn jacks on the AVR 510. Note that whenexternal amplifiers or devices are used, the vol-ume control is still controlled by the AVR 510,although additional volume controls on theexternal device may impact the volume settingsand output levels from the AVR 510.

External Audio Decoder ConnectionTo provide for ultimate flexibility, the AVR 510may be used in conjunction with optional,external decoders for digital audio systemsother than the AVR 510s own built-in DolbyDigital and DTS decoding system or with DVDplayers using the DVD Audio Format. If anexternal decoder is used, connect the outputjacks of the decoder to the 6-Channel DirectInputs , making sure to match channels.

These jacks may also be used for connections todevices such as DVD players or High DefinitionTelevision (HDTV) sets or decoders that featurebuilt-in digital surround decoders. Although thedigital decoding system in the AVR 510 will typi-cally provide audio performance that is superiorto other decoders, you may use these jacks toprovide an additional 6-channel input for connec-tion to a DVD player or HDTV set with a built-indecoder and discrete 6-channel analog outputs.

AC Power ConnectionsThis unit is equipped with two accessory ACoutlets. They may be used to power accessorydevices, but they should not be used with high-current draw equipment such as power ampli-fiers. The total power draw to each outlet maynot exceed 100 watts.

The Switched AC Accessory Outlet willreceive power only when the unit is on. This isrecommended for devices that have no powerswitch or a mechanical power switch that maybe left in the ON position.

NOTE: Many audio and video products go intoa Standby mode when they are used withswitched outlets, and cannot be fully turned onusing the outlet alone without a remote controlcommand.

The Unswitched AC Accessory Outlet will receive power as long as the unit isplugged into a powered AC outlet.

Finally, when all connections are complete, plugthe power cord into a nonswitched 110-volt ACwall outlet. Youre almost ready to enjoy theAVR 510!

18 SYSTEM CONFIGURATION

System Configuration

When all audio, video and system connectionshave been made, there are a few configurationadjustments that must be made. A few minutesspent to correctly configure and calibrate theunit will greatly add to your listening experience.

Speaker Selection and PlacementThe placement of speakers in a multichannelhome-theater system can have a noticeableimpact on the quality of sound reproduced.

No matter which type or brand of speakers isused, the same model or brand of speakershould be used for the left front, center andright front speakers. This creates a seamlessfront soundstage and eliminates the possibilityof distracting sonic disturbances that occurwhen a sound moves across mismatchedfront-channel speakers.

Speaker PlacementDepending on the type of center-channel speakerin use and your viewing device, place the centerspeaker either directly above or below your TV,or in the center behind a perforated front pro-jection screen.

Once the center channel speaker is installed,position the front left and front right speakersso that they are as far away from one anotheras the center-channel speaker is from the pre-ferred listening position. Ideally, the front-channelspeakers should be placed so that their tweetersare no more than 24" above or below thetweeter in the center-channel speaker.

Depending on the specifics of your roomacoustics and the type of speakers in use, youmay find that imaging is improved by movingthe left front and right front speakers slightlyforward of the center-channel speaker. If possi-ble, adjust all front loudspeakers so that theyare aimed at ear height when you are seatedin the listening position.

Using these guidelines, youll find that it takessome experimentation to find the correct locationfor the front speakers in your particular installa-tion. Dont be afraid to move things around untilthe system sounds correct. Optimize your speak-ers so that audio transitions across the front ofthe room sound smooth, and that sounds fromall speakers appear to arrive at the listening

position at the same time (without delay fromthe center speaker compared to the left andright speakers).

Surround speakers should be placed on the sidewalls of the room, at or slightly behind the listening position. The center of the speakershould face into the room. The speakers shouldbe located so that the bottom of the cabinet is at least two feet higher than the listenersears when the listeners are seated in thedesired area.

If side-wall mounting is not practical, thespeakers may be placed on a rear wall, behindthe listening position. Again, they should belocated so that the bottom of the cabinet is atleast two feet higher than the listeners ears.The speakers should be no more than six feetbehind the rear of the seating area.

Subwoofers produce nondirectional sound, sothey may be placed almost anywhere in aroom. Actual placement should be based onroom size and shape and the type of subwooferused. One method of finding the optimal loca-tion for a subwoofer is to begin by placing it inthe front of the room, about six inches from awall, or near the front corner of the room.Another method is to temporarily place thesubwoofer at your normal listening position,and then walk around the room until you finda spot where the subwoofer sounds best. Placethe subwoofer in that spot. You should alsofollow the instructions of the subwoofers man-ufacturer, or you may wish to experiment withthe best location for a subwoofer in your lis-tening room.

System SetupOnce the speakers have been placed in theroom and connected, the remaining steps in the setup process are to program the AVR 510s bass management system for thetype of speakers used in your system, calibratethe output levels, and set the delay times usedby the surround-sound processor.

You are now ready to power up the AVR 510 tobegin these final adjustments.

Right FrontSpeaker

Left FrontSpeaker

No morethan 24"

Center Front Speaker

At least 2 feet

At least 6 inches from ceiling

A) Front Channel Speaker Installation WithDirect-View TV Sets or Rear-Screen Projectors

Center FrontSpeaker

Optional Rear-Wall Mounting

TV or Projection Screen

Right FrontSpeaker

Left FrontSpeaker

No

mor

e th

an 6

feet

whe

n re

ar-m

ount

edsp

eake

rs a

re u

sed

B) The distance between the left and rightspeakers should be equal to the distancefrom the seating position to the viewingscreen. You may also experiment with plac-ing the left and right speakers slightly for-ward of the center speaker.



1. Plug the AC Power Cord into anunswitched AC outlet.

2. Press the Main Power Switch 1 in untilit latches and the word OFF on the topof the switch disappears inside the frontpanel. Note that the Power Indicator 3will turn amber, indicating that the unit isin the Standby mode.

3. Install the three supplied AAA batteries inthe remote as shown. Be certain to followthe (+) and () polarity indicators that areon the bottom of the battery compartment.

4. Turn the AVR 510 on either by pressing theSystem Power Control 2 on the frontpanel, or via the remote by pressing the AVRSelector f or any of the Input Selectorseg on the remote. The PowerIndicator 3 will turn green to confirm thatthe unit is on, and the Main InformationDisplay will also light up.

Using the On-Screen DisplayWhen making the following adjustments, youmay find it easier to use the AVR 510s on-screen display system. These easy-to-read dis-plays give you a clear picture of the current sta-tus of the unit and make it easy to see whichspeaker, delay, input or digital selection you aremaking.

To view the on-screen menus, make certain youhave made a connection from the VideoMonitor Out jack on the rear panel to thecomposite or S-Video input of your TV or pro-jector. In order to view the AVR 510s displays,the correct video source must be selected onthe video display.

IMPORTANT NOTE: When viewing the displayson a projection TV, it is important that they not beleft on the screen for an extended period of time.As with any video display, but particularly withprojectors, constant display of a static image suchas these menus or video game images may causethe image to be permanently burned into theCRT. This type of damage is not covered by theAVR 510 warranty and may not be covered bythe projector/TV sets warranty.

The AVR 510 has two on-screen display modes,Semi-OSD and Full-OSD. When makingconfiguration adjustments, it is recommendedthat the Full-OSD mode be used. This will placea complete status report or option listing onthe screen, making it easier to view the avail-able options. The Semi-OSD mode uses one-linedisplays only.

Making Configuration AdjustmentsThe full OSD system is always available bypressing the OSD button v. When this button is pressed, the MASTER MENU(Figure 1) will appear, and adjustments aremade from the individual menus. The semi-OSDsystem is also available as a system default,although it may be turned off by using theADVANCED SELECT menu. (See page33.) With the semi-OSD system, you may makeadjustments directly, by pressing the buttons onthe front panel or remote control for the specif-ic parameter to be adjusted. For example, pressthe Speaker Select button to set thespeaker configuration, etc.

Figure 1

Note that when the full OSD system is in use,the menu selections are not shown in the MainInformation Display Y. When the fullOSD menu system is used, OSD ON will appearin the Main Information Display Y and theOSD Indicator M will light to remind youthat a video display must be used. When thesemi-OSD system is used in conjunction withthe discrete configuration buttons, the on-screen display will show a single line of textwith the current menu selection. That selectionwill also be shown in the Main InformationDisplay Y.

To use the full OSD menu system, press theOSD button v. When the menu is on thescreen, press the / buttons n until theon-screen cursor is next to the item you wishto adjust, and then press the Set button p toadjust that item. Note that the menus willremain on the screen for 20 seconds, and thenthey will time-out and disappear from thescreen. The time-out may be increased to as

much as 50 seconds by going to theADVANCED SELECT menu, and changing the item titled FULL OSDTIME OUT.

Setting the System ConfigurationMemoriesThe AVR 510 features an advanced memorysystem that enables you to establish differentconfigurations for the speaker configuration,digital input, surround mode, delay times,crossover frequency and output levels for eachinput source. This flexibility enables you to custom-tailor the way in which you listen toeach source and have the AVR 510 memorizethose settings. This means, for example, thatyou may use different output levels or trims fordifferent sources, or set different speaker con-figurations with the resultant changes to thebass management system. Once these settingsare made, they will automatically be recalledwhenever you select that input.

The factory default settings for the AVR 510have all inputs configured for an analog source,stereo as the surround mode, the front left andright speakers set to large, and a subwooferconnected. Before using the unit, you will prob-ably want to change the settings for mostinputs so that they are properly configured toreflect the use of digital or analog inputs, thetype of speakers installed and the surroundmode specifics. Remember that since the AVR 510 memorizes the settings for each input individually, you will need to make these adjustments for each input used. However, oncethey are made, further adjustment is onlyrequired when system components arechanged.

To make this process as quick and as easy aspossible, we suggest that you use the full-OSDsystem with the on-screen menus, and stepthrough each input. Once you have completedthe settings for the first input, many settingsmay be duplicated for the remaining inputs. It isalso a good idea to set the configuration datain the order these items are listed in theMASTER MENU, as some settings require aspecific entry in a prior menu item. Rememberthat once the settings are made for one input,they must be made for all other input sourcesin your system.

* M A S T E R M E N U *

I N P U T S E T U P

S U R R O U N D S E T U P

S P E A K E R S E T U P

O U T P U T A D J U S T

C H A N N E L A D J U S T

M U L T I - R O O M

A D V A N C E D

E X I T

32



Input SetupThe first step in configuring the AVR 510 is toselect an input. This may be done by pressingthe front panel Input Source Selector !until the desired inputs name appears momen-tarily in the Main Information Display Y,and the green LED lights next to the inputsname in the front panel Input Indicators .The input may also be selected by pressing the appropriate Input Selector on the remotecontrol eg.

When using the full-OSD system to make thesetup adjustments, press the OSD button vonce so that the MASTER MENU (Figure 1)appears. Note that the cursor will be next tothe INPUT SETUP line. Press the Set but-ton p to enter the menu and the IN/OUTSETUP menu (Figure 2) will appear on thescreen. Press the / buttons o untilthe desired input name appears in the high-lighted video, as well as being indicated in thefront panel Input Indicators by the greenLED next to the desired input name. If the inputwill use the standard left/right analog inputs,no further adjustment is needed.

Figure 2

If you wish to associate one of the digitalinputs with the selected input source, press the button n on the remote while theIN/OUT SETUP menu (Figure 2) is onthe screen, and note that the on-screen cursorwill drop down to the DIGITAL IN line.Press the / buttons o until the nameof the desired digital input appears. To return tothe analog input, press the buttons until theword ANALOG appears. When the correctinput source appears, press the button nonce so that the cursor appears next toRETURN TO MENU, and press the Setbutton p.

To change the digital input at any time usingthe discrete function buttons and the semi-OSDsystem, press the Digital Input Select buttonq on the front panel or the remote.Within five seconds, make your input selectionusing the Selector buttons on the front panel

5 or the / buttons n on the remoteuntil the desired digital or analog input isshown in the Main Information Display Yand in the lower third of the video display connected to the AVR 510. Press the Set button p to enter the new digital inputassignment.

An exclusive Harman Kardon feature is the abil-ity to switch front panel jacks from their normaluse as inputs to output connections so thatportable recording devices may easily be con-nected. The front panel analog Video 4 Inputs^ are normally set as an input for use withcamcorders, video games and other portableaudio/video products, but they may be switchedto an output for connection to portableaudio/video recorders. To temporarily switchthem to outputs, you must first be at theIN/OUT SETUP menu. Press the button n until the on-screen cursor ispointing to the VIDEO 4 line. Press the button so that the word OUT is high-lighted. Note that the Input/Output StatusIndicator $ between the S and Compositevideo jacks will turn red, indicating that theanalog Video 4 jacks are now record outputs.

On the AVR 510, the Digital Coax 3 jack %is normally an input, but this may also beswitched to a digital output for use with CD-R/RW decks, MD recorders or other A/Vrecorders. To change the jack to an output,press the / buttons n while theIN/OUT SETUP menu is on the screen until the cursor is next to COAXIAL 3.Then press the / buttons o/ so thatthe word OUT is highlighted. Note that theInput/Output Status Indicator $ will turnred, indicating that the jack is now a recordoutput.

NOTE: A signal will be sent to this jack onlywhen the input selected for use by the AVR 510is digital. Digital signals will be passed throughregardless of their format, and which digitalinput (optical or coax) they are fed from.However, analog signals are not converted todigital, and the format of the signal (e.g., PCM,Dolby Digital or DTS) may not be changed.

Selection of the front panel jacks as an outputwill remain effective as long as the AVR 510 ison. Once the unit is turned off, the jacks willrevert to their normal use as an input when theunit is turned on again.

Surround SetupOnce the basic input setup has been com-pleted, the next step is to set the surroundmode you wish to use with an input. Since surround modes are a matter of personal taste,feel free to select any mode you wish youmay change it later. However, to make it easierto establish the initial parameters for theAVR 510, it is best to select Dolby Pro Logic formost analog inputs and Dolby Digital for inputsconnected to digital sources. In the case ofinputs such as a CD Player, Tape Deck or Tuner,you may wish to set the mode to Stereo (asthey are not typically used with multichannelprogram material), where it is unlikely that surround-encoded material will be used.Alternatively, the Logic 7 Music mode is a goodchoice for stereo-only source material.

It is easiest to complete the surround setupusing the full-OSD on-screen menus. From theMASTER MENU (Figure 1), press the /buttons n until the cursor is next to theSURROUND SETUP menu. Press the Setbutton p so that the SURROUNDSETUP menu (Figure 3 or 4) is on thescreen.

Figure 3

Figure 4

Since the factory default for all inputs is Stereo,the phrase SURR OFF will initially appear inhighlighted video (Figure 3). To change the sur-round mode while the cursor is next to thesurround line, press the / buttons ountil the desired surround modes nameappears in the highlighted video. As the modesare changed, a green LED will also light next tothe mode names in the Surround ModeIndicators on the front panel.

31

* S U R R O U N D S E T U P *

S U R R O U N D : D O L B Y

D I G I T A L

C E N T E R D E L A Y : 0 M S

S U R R D E L A Y : 0 0 M S

N I G H T : O F F M I D M A X

R E T U R N T O M E N U

* S U R R O U N D S E T U P *

S U R R O U N D : S U R R O F F

C E N T E R D E L A Y : M S

S U R R D E L A Y : M S

N I G H T :


31

31

31

* I N / O U T S E T U P *

I N P U T : V I D E O 1

D I G I T A L I N : A N A L O G

V I D E O 4 : I N O U T

C O A X I A L 3 : I N O U T


31



Note that the data lines next to the items in thescreen display will show either numbers or aseries of dashes, depending on whether or notthe specific parameter is adjustable. For exam-ple, the Center Delay and Night Mode items areonly adjustable for Dolby Digital, and the DelayTime is only adjusted for Dolby Digital andDolby Pro Logic. Note, also, that Dolby Digitaland DTS will only appear as choices (Figure 4)when a digital input was previously selected.

Depending on the Surround mode selected, youwill now proceed to change either the delaytime or the crossover frequency. For DolbyDigital and Dolby Pro Logic, pressing the /n buttons on the remote will take you to thedelay settings.

Delay SettingsIf Dolby Digital or Dolby Pro Logic is selected asthe surround mode for an input, you may needto adjust the delay time setting. Note that thedelay time is not adjustable for any othermodes.

Due to the different distances between the listening position for the front-channel speakersand the surround speakers, the amount of timeit takes for sound to reach your ears from thefront versus surround speakers differs. You maycompensate for this difference through the useof the delay settings to adjust the timing forthe specific speaker placement and acousticconditions in your listening room or home theater.

The factory setting is appropriate for mostrooms, but some installations create an uncom-mon distance between the front and surroundspeakers that may cause the arrival of front-channel sounds to become disconnected fromsurround-channel sounds.

To resynchronize the front and surround chan-nels, follow these steps:

1. Measure the distance from the listeningposition to the front speakers.

2. Measure the distance from the listeningposition to the surround speakers.

3. Subtract the distance to the surround speak-ers from the distance to the front speakers.

a. When setting the delay time for theDolby Digital surround modes, the opti-

mal delay time is the result of that sub-traction. For example, if the front speak-ers are ten feet away and the surroundspeakers are five feet away, the optimaldelay time is figured as 105=5. Thus, inthis example, the delay time for DolbyDigital should be set at five milliseconds.

b. When setting the delay time for the ProLogic mode, take the result of the sub-traction and add 15 to obtain the opti-mal delay time. For example, if the frontspeakers are ten feet away and the sur-round speakers are five feet away, theoptimal delay time is figured as105+15=20. Thus, in this example, thePro Logic delay should be set at twentymilliseconds.

NOTE: The DTS, Logic 7, Hall and Theatermodes use a fixed, nonadjustable delay time.

The Dolby Digital mode also includes a separatesetting for the Center Channel Delay mode,since the discrete nature of these signals makesthe location of the center-channel speaker morecritical. To calculate the delay for the centerchannel, measure the distance from the pre-ferred listening position in the center of theroom to both the center-channel speaker andeither the left or right speaker.

If the distances are equal, no further adjustmentis required and the center delay should be set tozero. If the distance to the front speakers isgreater than the dis

Documents

AVR 510 om.pdf