Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
AUTOMATIC MEDIUM SPEED LINEAL 4 AND 6 CORNER FOLDER
MODELO: PACKGLUED VI-CS
[email protected](33) 2469 2202
CS PARAMETERS
ModelProcessed Materials
Carton board max.Corrugated flute type
CapabilitySpeed max.
Inching speedThickness of folded box max.
Blank widthTotal Power
Compressed airAir compressor capacity
Air tank capacity Dimensions & weightLength*Width*Height
Net Weight
650CS
650 MMA, B, E
350 m/min10 m/min
12mm650 mm22.5kw6 bar
10 m³/h60 L
13*1.4*1.8m5T
800CS
800 MMA, B, E
350 m/min10 m/min
20mm800 mm23.5 kW
6 bar10 m³/h
60 L
16.5 *1.4*1.8m6.6T
1100CS
1100 MM A, B, E
350 m/min10 m/min
20mm1100 mm23.7 kW
6 bar10 m³/h
60 L
16.5*1.7*1.9m6.8 T
AUTOMATIC MEDIUM SPEED LINEAL 4 AND 6 CORNER FOLDER
[email protected](33) 2469 2202
CS FEATURES INTRODUCTION
Paper feeding department
•Rail width can be h orizontal ly adj usted and set by seven pieces 30mm thickened feeding belt and 10mm metal board.• Operators can operate feeder switch in any regional.
Embossing drive wheel guide the feeding section belt, side feed gates in the right and left are adjustable ac-cording to the products.
•Vibration device coordinate with motor which helps machine consecutive and automatic feeding quick and simply. Feeder section can stack 400MM height paper board.
Aligner section
•The paper board sent from feeder section will be co-rrected by aligner section to ensure transmission accura tely.
• Pressing drive pressure can be adjusted up and down to accommodate different paper board thickness.
Pre folding section
•Special first folding line pre fold 180°. Third line 165 which perfectly meeting the requirements of automatic pac-kaging industry.
•Independently motorized motor control simultaneous feeding mode with the main motor.
• Feeder section equipped with three pieces feeding knife, adjust the asymmetrical lengths as per the box sample.
AUTOMATIC MEDIUM SPEED LINEAL 4 AND 6 CORNER FOLDER
[email protected](33) 2469 2202
CS FEATURES INTRODUCTION
Lower gluing tank
•Lower gluing tank is large volume.
•Easy to remove and clean.
•Electronic upper gluing system by guns.
Folding and closing
•The Second and fourth fol ding line 180°
•Folding and closing section transmit from right and left side ,the belt speed can be adjusted separately and co-rrect the way of box running to ensure straightly delivery.
Trombone section
•Up and down belt can be adjusted separately.
•Equipped with photo electronic counting device and kicking paper device, which can press the paper after accounting and make it easy to pa ck . Also e quipped with feeding paper inspection device.
AUTOMATIC MEDIUM SPEED LINEAL 4 AND 6 CORNER FOLDER
[email protected](33) 2469 2202
Transmission
•Equipped with special additional sponge belt for the press of boxes valley part.
•Upper section moves back and forward, allowing for di-fferent box length.
• Upper section moves back and forward, allowing for different box length.
4 and 6 corner device
•Motorized and untimed electronic back folding system with intelligent servo motor technology.
Spraying System
•Equipped with three guns, convenient in the production of 4/6 corner box and various special shaped box, gluing quickly and accurately sizing.
AUTOMATIC MEDIUM SPEED LINEAL 4 AND 6 CORNER FOLDER
[email protected](33) 2469 2202
SAMPLES PARAMETERS
Straight-line boxModel
AB
C (Min)
Crash lock bottom boxModel
AB
C(Min)D(Min)E(Min)
Tapered boxModel
AB
C(Min)D(Min)E(Min)
4 corners boxModel
AB
C(Min)D(Min)E(Min)
6 corners boxModel
AB
C(Min)D(Min)E(Min)
650Type75-65060-650
35
650Type160-65090-900
203040
650Type160-65090-650
403520
650Type160-500120-65020-200
9080
650Type250-650120-80020-200
9080
800Type75-80060-800
35
800Type160-80090-900
203040
800Type160-80090-800
403520
800Type160-800120-80020-200
9080
800Type250-800120-80020-200
9080
1100Type75-110060-800
35
1100Type160-110090-900
203040
1100Type160-110090-1100
403520
1100Type160-1100120-100020-200
9080
1100Type250-1100120-80020-200
9080
AUTOMATIC MEDIUM SPEED LINEAL 4 AND 6 CORNER FOLDER
[email protected](33) 2469 2202
STRAIGHT-LINE TYPE
CRASH LOCK BOTTOM TYPE
FOUR CORNERS TYPE
SIX CORNERS TYPE
AUTOMATIC MEDIUM SPEED LINEAL 4 AND 6 CORNER FOLDER
[email protected](33) 2469 2202
CONFIGURATION LIST
Main Board
• Mail Wall plate 14 mm which is International standard steel plate processing cold and hot treatment
Conveying motor
• Qiaobang-Made in China
Touch Display
• Taiwan-WEINVIEW
Main Motor
• ZHONGLONG-Made in China
PLC controller
• Taiwan-FATEK
Contactor
• France-Schneider
Board for conveyor
• Conveyor board 1 0 mmwhich is International stan-dard steel plate proces-sing cold and hot treat-ment
Converter
• German-Rexroth
Circuit Breaker
• France-Schneider
PACKGLUED VI GS SERIES
Automatic High Speed Lineal 4 and 6 corner Folder
[email protected] www.packmach.mx
Main Board Mail Wall plate 16mm
which is International standard steel plate processing cold and hot treatment
Main motor SIEMENS Germany
Circuit Breaker France Schneider
Conveying motor Qiaobang
Contactor France Schneider
Touch Display Taiwan weinview
Board for conveyor The bending part 8mm
which is International standard steel plate processing cold and hot treatment
Converter Germany Rexroth
PLC controller Taiwan FATEK
PACKGLUED VI GS SERIES
Automatic High Speed Lineal 4 and 6 corner Folder
[email protected] www.packmach.mx
Main Board Mail Wall plate 16mm
which is International standard steel plate processing cold and hot treatment
Main motor SIEMENS Germany
Circuit Breaker France Schneider
Conveying motor Qiaobang
Contactor France Schneider
Touch Display Taiwan weinview
Board for conveyor The bending part 8mm
which is International standard steel plate processing cold and hot treatment
Converter Germany Rexroth
PLC controller Taiwan FATEK
PACKGLUED VI GS SERIES
Automatic High Speed Lineal 4 and 6 corner Folder
[email protected] www.packmach.mx
Main Board Mail Wall plate 16mm
which is International standard steel plate processing cold and hot treatment
Main motor SIEMENS Germany
Circuit Breaker France Schneider
Conveying motor Qiaobang
Contactor France Schneider
Touch Display Taiwan weinview
Board for conveyor The bending part 8mm
which is International standard steel plate processing cold and hot treatment
Converter Germany Rexroth
PLC controller Taiwan FATEK
AUTOMATIC MEDIUM SPEED LINEAL 4 AND 6 CORNER FOLDER
[email protected](33) 2469 2202
CONFIGURATION LIST
Intermediate relay
• France-Schneider
Photo electricity
• KEYENCE
Conveying belt
• Switzerland-Habasit
Chrome bar
•Through quenching-tempering
Switch power supply
• Changxin
Base belt
• Japan-NITTA
Transmission bearing
• NSK-Japan
Press Switch+ Remote controller
• Telecrane
Button
• France-Schneider
Feeding Belt
• Japan-NITTA
Bearing
• NSK-Japan
Mound layer, roller
• Special section bar, hot processed
PACKGLUED VI GS SERIES
Automatic High Speed Lineal 4 and 6 corner Folder
[email protected] www.packmach.mx
Button France Schneider
Intermediate relay France Schneider
Photo electricity KEYENCE
Transmission bearing NSK(Japan)
Bearing NSK(Japan)
Conveying belt Switzerland Habasit
Chrome bar Through quenching-
tempering
Press Switch+ Remote
controller Telecrane
Switch power supply Changxin
Base belt Germany Siegling
Feeding Belt Japan NITTA
Mound layer, roller Special section bar,
hot processed
PACKGLUED VI CS SERIES
Automatic Medium Speed Lineal 4 and 6 corner Folder
[email protected] www.packmach.mx
Chrome bar Through quenching-
tempering
Intermediate relay France Schneider
Button France Schneider
Photo electricity KEYENCE
Conveying belt Switzerland Habasit
Bearing NSK(Japan)
Transmission bearing NSK(Japan)
Press Switch+ Remote controller
Telecrane
Mound layer, roller Special section bar, hot
processed
Switch power supply Changxin
Feeding Belt Japan NITTA
Base belt Japan NITTA
PACKGLUED VI GS SERIES
Automatic High Speed Lineal 4 and 6 corner Folder
[email protected] www.packmach.mx
Button France Schneider
Intermediate relay France Schneider
Photo electricity KEYENCE
Transmission bearing NSK(Japan)
Bearing NSK(Japan)
Conveying belt Switzerland Habasit
Chrome bar Through quenching-
tempering
Press Switch+ Remote
controller Telecrane
Switch power supply Changxin
Base belt Germany Siegling
Feeding Belt Japan NITTA
Mound layer, roller Special section bar,
hot processed
PACKGLUED VI CS SERIES
Automatic Medium Speed Lineal 4 and 6 corner Folder
[email protected] www.packmach.mx
Chrome bar Through quenching-
tempering
Intermediate relay France Schneider
Button France Schneider
Photo electricity KEYENCE
Conveying belt Switzerland Habasit
Bearing NSK(Japan)
Transmission bearing NSK(Japan)
Press Switch+ Remote controller
Telecrane
Mound layer, roller Special section bar, hot
processed
Switch power supply Changxin
Feeding Belt Japan NITTA
Base belt Japan NITTA