Step 1 Step 2

LEG BRACE ASSEMBLY DETAIL

Cordless Drill

#2 Square Drive Bit (included)

+

Ax6

B x8

3" Bugle Head Screw

2" Pan Deck Screw

Harware Included Tools Needed

Assembly Guide

MHSDAC2236Mayhew Sling Dining Arm Chair

A x 1

A x 1

A x 2

A x 2

A x 2

A x 1

B x 2 B x 2

B x 2

B x 2

B x 2

SEAT ASSEMBLY DETAILFit the mortises & tendonsin the seat and back intoeach other and fastenusing the indicated screwsin pre-drilled holes

ARM ASSEMBLY DETAILPlace the back againstthe arm support in thenotched area and fastenusing indicated screwsin predrilled holes

Properly position the leg brace assemblybetween the chair legs by fitting the mortiseand tendon jointery in each corner.

Fasten the leg brace assemblyto each chair legs using the indicatedscrews in the pre-drilled pocket holes

Step 1

Set the Arm and Seat Assembly forward onto the front of theArms and set the Back Assembly on top. Be sure to do thison top of a soft surface to avoid damaging the arms.Fasten the Back to the Seat using eight - 4" Buglehead Screws.Keeping the Arms Supports even with the outside edges of theBack, fasten them using two - 3" Buglehead Screws.

Mayhew Sling Dining Swivel Rocker Assembly Guide

Tools Required

Hardware Included

Cordless Drill #2 Square Drive Bit (Included)

Allen Wrench (Included)

2 - 3"Buglehead Screws

8 - 4"Buglehead Screws

Back Assembly

Arm & Seat AssemblyKeep the Arm Support even with the outside edge of the Back.

3" Buglehead Screws 4" Buglehead Screws

Wrench

6 - 5/16" X 1 3/4"Allen Head Bolts

6 - 5/16"Flange Nuts

6 - 5/16"Lock Washers

6 - 5/16"Square Nuts

3 - Fiberglass Springs

3 - Aluminum Plates

1 - Swivel Mechanism6 - 5/16" X 1 1/4"Allen Head Bolts

Step 2

Step 4

Lift the top of the chair and set the swivel steminto the receiver of the base. Push firmly onto thechair until it sits securely in the receiver.

Step 2 Detail

Step 3 Detail

Using 6 - 5/16"x 1 1/4"Allenhead Bolts and5/16" Flangenuts, fasten the3-Fiberglass Springsand 1 - AluminumPlate to the seat bracketThe Springs should pointtowards the front of thechair. Only hand tightenthe nuts until all six boltsare installed, then align thesprings and fully tighten.

5/16" Flange Nuts

5/16" x 1 1/4" Bolts

Aluminum Plate

Fiberglass Springs

Fasten the Swivel Mechanism tothe Figerglass Springs, using2-Aluminum Plates, 6 - 5/16"x 1 3/4"Allenhead Bolts, Lock Washersand Square Nuts. Only hand tightenthe nuts until all six bolts areinstalled then fully tighten.

Fiberglass Springs

5/16" x 1 3/4" Bolts

Aluminum Plate

Aluminum Plate

Swivel Mechanism

5/16" Lock Washers5/16" Square Nuts

Step 3

#GCIT4472D, #GCIT4472C, #GCIT4472Bin Garden Classic Collection

HARDWARE PACKAGE16 ¼" x 2" Allen Head Bolts16 ¼" Flange Nuts2 Umbrella Knobs44 3" Screws24 1½ " Screws1 Allen Wrench

PACKAGE CONTENTS1 Top4 Bases4 Long Cross Supports2 Short Cross Supports4 Footrests (Bar and Counter Height)1 Umbrella Holder1 Umbrella Plug8 Braces1 Hardware Package

TOOLS NEEDED:Hammer

7/16" WrenchCordless Drill/ScrewdriverAllen Wrench (Included)

Firmly tap bolts into pre-drilledholes before tightening.

CORRECT INCORRECT1 2 3 4 5

Use to measure bolts

Garden Classic Table

NOTE: Bar and Counter Height Only

Assembly Directions for44"x72" Rectangular Table

Be sure to use 1½"

screws when fastening braces.

!

Base

Long Cross Support

Short Cross Support

Upr

ight

Top Boards

Apron

Brace

UmbrellaHolder

Cur

ved

End

Boar

d

Footrest

Garden Classic Table

STEP #1 - First assemble both Bases and Long Cross Supports using 3" Screws.Please note: � ere are two outside Bases and two center Bases. � e two center Bases have extra mortises for the Umbrella Holder and Short Cross Supports (see Step #3).

STEP #2 - Attach the � rst Base Assembly to thealuminum frame of the Top using8- ¼ " x 2" Allen Head Bolts.

STEP #3 - Attach the two Short Cross Supports and the Umbrella Holder to the Base using 3" Screws.

STEP #4 - First attach the second Base Assembly to the aluminum Frame of the Top using 8- ¼ " x 2"Allen Head Bolts. Second fasten the Base Assembly to the Short Cross Pieces and Umbrella Holder using 3" Screws.

STEP #5 - Last, attach the Braces to the Top and the Base using 1½ " Screws.Caution: Do not overtighten the Screws into the Top!

UmbrellaKnobs

¼ " x 2" Allen Head Bolts

3" Screws

3" Screws

3" Screws

¼ " x 2" Allen Head Bolts

Footrest

1½ " Screws (circled)

Cross Support