Step 1 Step 2
LEG BRACE ASSEMBLY DETAIL
Cordless Drill
#2 Square Drive Bit (included)
+
Ax6
B x8
3" Bugle Head Screw
2" Pan Deck Screw
Harware Included Tools Needed
Assembly Guide
MHSDAC2236Mayhew Sling Dining Arm Chair
A x 1
A x 1
A x 2
A x 2
A x 2
A x 1
B x 2 B x 2
B x 2
B x 2
B x 2
SEAT ASSEMBLY DETAILFit the mortises & tendonsin the seat and back intoeach other and fastenusing the indicated screwsin pre-drilled holes
ARM ASSEMBLY DETAILPlace the back againstthe arm support in thenotched area and fastenusing indicated screwsin predrilled holes
Properly position the leg brace assemblybetween the chair legs by fitting the mortiseand tendon jointery in each corner.
Fasten the leg brace assemblyto each chair legs using the indicatedscrews in the pre-drilled pocket holes
Step 1
Set the Arm and Seat Assembly forward onto the front of theArms and set the Back Assembly on top. Be sure to do thison top of a soft surface to avoid damaging the arms.Fasten the Back to the Seat using eight - 4" Buglehead Screws.Keeping the Arms Supports even with the outside edges of theBack, fasten them using two - 3" Buglehead Screws.
Mayhew Sling Dining Swivel Rocker Assembly Guide
Tools Required
Hardware Included
Cordless Drill #2 Square Drive Bit (Included)
Allen Wrench (Included)
2 - 3"Buglehead Screws
8 - 4"Buglehead Screws
Back Assembly
Arm & Seat AssemblyKeep the Arm Support even with the outside edge of the Back.
3" Buglehead Screws 4" Buglehead Screws
Wrench
6 - 5/16" X 1 3/4"Allen Head Bolts
6 - 5/16"Flange Nuts
6 - 5/16"Lock Washers
6 - 5/16"Square Nuts
3 - Fiberglass Springs
3 - Aluminum Plates
1 - Swivel Mechanism6 - 5/16" X 1 1/4"Allen Head Bolts
Step 2
Step 4
Lift the top of the chair and set the swivel steminto the receiver of the base. Push firmly onto thechair until it sits securely in the receiver.
Step 2 Detail
Step 3 Detail
Using 6 - 5/16"x 1 1/4"Allenhead Bolts and5/16" Flangenuts, fasten the3-Fiberglass Springsand 1 - AluminumPlate to the seat bracketThe Springs should pointtowards the front of thechair. Only hand tightenthe nuts until all six boltsare installed, then align thesprings and fully tighten.
5/16" Flange Nuts
5/16" x 1 1/4" Bolts
Aluminum Plate
Fiberglass Springs
Fasten the Swivel Mechanism tothe Figerglass Springs, using2-Aluminum Plates, 6 - 5/16"x 1 3/4"Allenhead Bolts, Lock Washersand Square Nuts. Only hand tightenthe nuts until all six bolts areinstalled then fully tighten.
Fiberglass Springs
5/16" x 1 3/4" Bolts
Aluminum Plate
Aluminum Plate
Swivel Mechanism
5/16" Lock Washers5/16" Square Nuts
Step 3
#GCIT4472D, #GCIT4472C, #GCIT4472Bin Garden Classic Collection
HARDWARE PACKAGE16 ¼" x 2" Allen Head Bolts16 ¼" Flange Nuts2 Umbrella Knobs44 3" Screws24 1½ " Screws1 Allen Wrench
PACKAGE CONTENTS1 Top4 Bases4 Long Cross Supports2 Short Cross Supports4 Footrests (Bar and Counter Height)1 Umbrella Holder1 Umbrella Plug8 Braces1 Hardware Package
TOOLS NEEDED:Hammer
7/16" WrenchCordless Drill/ScrewdriverAllen Wrench (Included)
Firmly tap bolts into pre-drilledholes before tightening.
CORRECT INCORRECT1 2 3 4 5
Use to measure bolts
Garden Classic Table
NOTE: Bar and Counter Height Only
Assembly Directions for44"x72" Rectangular Table
Be sure to use 1½"
screws when fastening braces.
!
Base
Long Cross Support
Short Cross Support
Upr
ight
Top Boards
Apron
Brace
UmbrellaHolder
Cur
ved
End
Boar
d
Footrest
Garden Classic Table
STEP #1 - First assemble both Bases and Long Cross Supports using 3" Screws.Please note: � ere are two outside Bases and two center Bases. � e two center Bases have extra mortises for the Umbrella Holder and Short Cross Supports (see Step #3).
STEP #2 - Attach the � rst Base Assembly to thealuminum frame of the Top using8- ¼ " x 2" Allen Head Bolts.
STEP #3 - Attach the two Short Cross Supports and the Umbrella Holder to the Base using 3" Screws.
STEP #4 - First attach the second Base Assembly to the aluminum Frame of the Top using 8- ¼ " x 2"Allen Head Bolts. Second fasten the Base Assembly to the Short Cross Pieces and Umbrella Holder using 3" Screws.
STEP #5 - Last, attach the Braces to the Top and the Base using 1½ " Screws.Caution: Do not overtighten the Screws into the Top!
UmbrellaKnobs
¼ " x 2" Allen Head Bolts
3" Screws
3" Screws
3" Screws
¼ " x 2" Allen Head Bolts
Footrest
1½ " Screws (circled)
Cross Support