Airflex® Air Cooled Disc Clutches and Brakes Cooled Disc Clutches an… · EATON Airflex® Clutches & Brakes 10M1297GP November 2012 181 Airflex® DBA Description Section E Model

EATON Airflex® Clutches & Brakes 10M1297GP November 2012180

DBA Description ...................................................................................................................................................................... 181

DBA Brake Elements ................................................................................................................................................................. 183

DBA Technical information ........................................................................................................................................................ 184

DBB and DBBS Description .................................................................................................................................................... 185

DBB Brake Elements ................................................................................................................................................................. 187

DBB Technical Information ........................................................................................................................................................ 188

DBBS Brake Elements ............................................................................................................................................................... 189

DBBS Technical Information ...................................................................................................................................................... 191

Type DC Description ................................................................................................................................................................ 192

DC Technical and Dimensional Data .......................................................................................................................................... 194

Type FHB Description ............................................................................................................................................................... 196

Floating Housing Brake Technical and Dimensional Data ........................................................................................................... 197

Selection Procedure ................................................................................................................................................................ 200

Airflex® Air Cooled Disc Clutches and BrakesSection E

EATON Airflex® Clutches & Brakes 10M1297GP November 2012 181

Airflex® DBA DescriptionSection E

Model DBA brakes are spring applied, pressure released, disc style brakes. They develop equal torque in either direction of rotation. Their torque and thermal capacities allow them to be used in the most demanding applications.

Brake construction and operation is shown in the figure. Pressurizing the brake compresses the brake springs and withdraws the clamping plates from the brake discs. Standard brakes are furnished with either one or two discs, which are free to move axially.

Model DBA uses a rubber diaphragm to form the releasing pressure chamber and to serve as the releasing piston. Brake friction material is attached to stationary components. Brake discs are either solid or ventilated. The disc type is indicated by an S for solid, or V, for ventilated, in the brake model des-ignation. Solid discs are used in applications requiring a heat sink and/or where engagement is infrequent. Ventilated discs are recommended for cyclic applications.

Torque ratings listed are for brakes with a standard compli-ment of springs. The quantity of springs can be varied to customize the torque of the brake to suit a particular applica-tion. Consult the factory for brake torque of units with non-standard spring configurations.

Brake sizes are indicated by the number of brake discs and the disc diameter in inches. For instance, size 229DBA has two discs 29 inches in diameter.

Features

Large friction area.

Allows brakes to absorb and dissipate high energy loads as-sociated with high cyclic and high inertia stops.

Minimal adjustment required for lining wear.

Single disc units require no wear adjustment and dual disc units require only one wear adjustment during the long life of the friction material.

Where used:

• Can making machines

• Draglines

• Power shovels

• Conveyors

• Power presses


Airflex® DBA Component partsSection E

Item Number Description

1 Mounting Flange2 Stud3 Clamp Tube4 Disc5 Friction Disc6 Flat Head Screw7 Pressure Plate8 Spring Housing9 Locknut10 Outer Clamp Ring11 Diaphragm12 End Plate13 Inner Clamp Ring14 Hex Head Screw15 Lockwasher16 Hex Head Screw17 Lockwasher18 Spring Retainer Plate19 Inner Spring20 Outer Spring21 Hex Head Screw22 Gear23 Reaction Plate24 Release Spring25 Wear Spacer26 Name Plate27 Self Tapping Screw28 Warning Decal29 Washer30 Air Tube31 Air Tube32 90 Deg. Street Elbow33 90 Deg. Male Elbow34 Cross35 Hose Assembly36 Flow Control Valve37 Bushing

34

16, 17

74

13

231

36

9 1025

24

2

22

35

37

12

32

14, 15

3

Dual disc element shown

8 15, 2129

26, 27, 28

19, 20

186

5

33

11

30, 31


Airflex® DBA Brake ElementsForm DBA808 — Dimensional and Technical Data Section E

English Dimensions in inches

17DBA 2.00 21.000 17.25 10.00 5.38 24.998 0.78 1/2-1421DBA 2.00 2 3.000 21.00 12.12 7.62 26.498 1.06 1-11 1/229DBA 2.75 31.000 28.00 14.75 10.25 33.998 1.06 1-11 1/2 Basic Size D25 H H11 H13 H16 G L 02

17DBA 51 533 438 254 137 634,9 20 1/2-1421DBA 51 584 533 308 194 673,0 27 1-11 1/229DBA 70 787 711 375 260 863,5 27 1-11 1/2SI Dimensions in millimeters


117DBA 2.50 4.25 12.55 11.19 4.88 1.00 10.69 4.88 1.88217DBA 3.25 4.25 15.77 14.41 6.50 1.88 13.41 6.50 1.88121DBA 2.88 5.75 13.19 11.33 2.50 2.12 11.33 5.62 2.00221DBA 3.88 5.88 16.47 14.61 5.63 2.12 14.23 5.62 2.25129DBA 3.94 7.38 15.51 13.75 3.50 2.25 15.06 5.88 2.38229DBA 4.88 7.19 19.13 17.38 7.12 2.25 18.06 7.00 3.12329DBA 5.63 6.88 22.93 10.63 2.34 Size Bore Range Ventilated Disc Types Solid Disc Types

Min. Max. D D1 D7 D29 D D7 D29

117DBA 64 108 319 284 124 25 272 124 48217DBA 79 108 401 366 165 48 341 165 48121DBA 73 146 335 287 64 54 288 143 51221DBA 98 149 418 371 143 54 361 143 57129DBA 105 187 394 349 89 57 383 149 60229DBA 124 182 486 441 181 59 459 178 79329DBA 143 175 582 270 59 SI Dimensions in millimeters

Notes:

All ventilated disc brakes are furnished with an approximate 15.5 inch (394 mm) length of flexible hose and a flow control valve having a 1-11 1/2 American National Pipe Thread port.

Tolerance +0.000/-0.003 in (+0,00/-0,08 mm)

American National Pipe Thread

H11

H13

D29 D7

D25D

H16

G

Single Disc Brake

H11

H13

D29 D7

D25D

D1

G

O2

H16

Dual Disc Brake

6 Equally spacedmounting holes on a

H bolt circle.

Special Mounting Flangesare available which permit

direct mounting to 800Series frame motors.

See Note


Airflex® DBA ElementsDimensional and Technical Data Section E

English lbin psi in3 in2 lbft2 lb rpm

117DBAS 146148 413113 29300 85 100 270 18 95 410 2300217DBAS 146152 413248 52600 85 100 540 35 160 455 2300121DBAS 146145 413534 69800 85 160 406 42 130 610 1900221DBAS 146151 413535 129300 85 160 812 80 270 565 1900129DBAS 146162 413801 176700 100 310 890 152 325 950 1500229DBAS 146163 414126 336200 100 310 1780 292 520 1150 1500 Gear Mr Minimum Disc Disc Part Part Torque Releasing Releasing Friction & & Maximum Size Number Number Rating Pressure Volume Area Gear Gear Housing Speed

Wk2 Weight J Mass117DBAS 146148 413113 3310 5,9 1,64 1742 0,76 43 186 2300217DBAS 146152 413248 5940 5,9 1,64 3483 1,47 72 206 2300121DBAS 146145 413534 7890 5,9 2,62 2619 1,76 59 276 1900221DBAS 146151 413536 14600 5,9 2,62 5237 3,36 122 256 1900129DBAS 146162 413801 20000 6,9 5,08 5741 6,38 147 430 1500229DBAS 146163 414126 38000 6,9 5,08 11481 12,26 236 521 1500SI Nm bar dm3 cm2 kgm2 kg rpm

English lbin in3 in2 lbft2 lb rpm

117DBAV 146148 413113 20500 100 270 10 70 320 1300217DBAV 146152 413248 38000 100 540 20 112 363 1300121DBAV 146145 413534 52500 160 406 30 105 480 1000221DBAV 146151 413535 96000 160 812 60 210 565 1000129DBAV 146162 413683 113000 310 890 97 185 970 900229DBAV 146163 413585 216000 310 1780 191 340 1150 900329DBAV 146210 415080 339000 310 2670 285 495 1549 900 Gear Mr Disc Disc Part Part Torque Releasing Friction & & Maximum Size Number Number Rating Volume Area Gear Gear Housing Speed

Wk2 Weight J Mass117DBAV 146148 413113 2320 1,64 1742 0,42 32 145 1300217DBAV 146152 413248 4290 1,64 3483 0,84 51 164 1300121DBAV 146145 413534 5930 2,62 2619 1,26 48 217 1000221DBAV 146151 413535 10800 2,62 5237 2,52 95 256 1000129DBAV 146162 413683 12800 5,08 5741 4,07 84 439 900229DBAV 146163 413585 24400 5,08 11481 8,02 154 521 900329DBAV 146210 415080 38400 5,08 17223 11,97 224 708 900SI Nm dm3 cm2 kgm2 kg rpm

Notes:

Basic part number only. Does not include gear. Gear must be ordered separately with the bore and keyway requirements.

Dynamic torque shown. Static torque approximately 1.15 greater. Torque values are for new linings. Torque decreases with lining wear. At the worn out condition, torque is approximately 0.66 of values shown.

Torque ratings are for units with a standard complement of springs. Consult factory for torque ratings of units with non-standard spring configurations.

Maximum allowable cylinder pressure is 120 psi (8,3 bar).

Absolute volume of releasing cavity.

Minimum releasing pressure 60 psi (4,1 bar).


Airflex® DBB DescriptionSection E

Model DBB brakes are spring applied, pressure released, disc style brakes. They develop equal torque in either direction of rotation. Their torque and thermal capacities allow them to be used in the most demanding applications.

Brake construction and operation is shown in the figure. Pressurizing the brake compresses the brake springs and withdraws the clamping plates from the brake discs. Standard brakes are furnished with either one or two discs, which are free to move axially.

Model DBB uses a conventional piston design to release the brake discs. The rotating component of the DBB style brake is a very low inertia friction disc core with riveted on friction discs. The low inertia of the rotating components coupled with the high heat sink capacity of the stationary members al-low these units to provide superior performance in high cyclic applications. In applications requiring higher speed opera-tion or where precise balance of the rotating components is required, the DBBS style is offered, which utilizes a solid rotor and stationary friction material. Similar to the DBAS design, the DBBS should only be used for applications where brake engagement is non-cyclic.

Torque ratings listed are for brakes with a standard compli-ment of springs. The quantity of springs can be varied to customize the torque of the brake to suit a particular applica-tion. Consult the factory for brake torque of units with non-standard spring configurations.

Brake sizes are indicated by the number of brake discs and the disc diameter in inches. For instance, size 225DBB has two discs 25 inches in diameter.

Features

Low inertia friction disc assembly.

Reduces the overall inertia that must be stopped.

Optional split friction discs.

Allows removal of friction discs without disturbing other com-ponents of drive system in mid-shaft brake arrangement.

Long wearing, self lubricating PolyPak* seals.

Eliminates premature twisting failure and requires no external lubrication.

Where used:

• Bottling equipment

• Power Shovels

• Conveyors

• Shears

• Power Presses


Airflex® DBB DescriptionSection E


1 Mounting Flange2 Stud3 Friction Disc Sub-Assembly4 Friction Disc5 Friction Disc Core6 Rivet7 Washer8 Clamp Tube9 Pressure Plate10 Spring Housing11 Flat Washer12 Locknut


25 Ring Gear26 Pipe Nipple27 Elbow28 Pipe Cross29 Hose Assembly30 Pipe Nipple31 Flow Control Valve32 45 Deg. Street Elbow33 Pipe Reducer34 Hose Assembly35 Spring Retainer


13 Cylinder14 Hex Head Screw15 Outer Seal16 Spring17 Inner Seal18 Spacer Tube19 Gear20 Wear Spacer21 Reaction Plate22 Release Spring23 Flat Washer24 Hex Head Screw

28, 32, 33

15

14

9

16

22

19

35

26

34

31

113

21

2

8

25

20

6, 7

12


18

27

30

17

13

10

29

23, 24

1

45


Airflex® DBB Brake ElementsDimensional and Technical Data Section E


9DBB 1.00 0.25 3.12 12.125 8.375 12.37 3/8-18

15DBB 1.47 0.38 0.38 6.00 18.375 14.375 18.94 1/2-14

20DBB 1.50 0.38 1.00 8.50 23.250 18.250 23.82 1/2-14

25DBB 1.75 0.25 0.75 11.50 30.630 24.375 30.89 1/2-14

38DBB 2.45 0.25 1.25 16.50 44.750 36.375 45.01 3/4-14Size D31 D44 D45 H16 J J1 J2 O2

9DBB 25 6 79 308.0 212.7 314 3/8-1815DBB 37 10 10 152 466.7 365.1 481 1/2-1420DBB 38 10 25 216 590.6 463.5 605 1/2-1425DBB 44 6 19 292 778.0 619.1 785 1/2-1438DBB 62 6 32 419 1136.7 923.9 1143 3/4-14SI Dimensions in millimeters


109DBB 1.68 2.50 7.26 1.75 6.06209DBB 1.94 2.56 8.70 4.00 7.53309DBB 2.13 2.63 9.06 5.25 9.06115DBB 2.13 2.50 4.38 2.88 7.52215DBB 3.06 4.25 11.16 4.38 9.23120DBB 3.00 5.88 10.87 3.00 9.37220DBB 3.75 6.00 13.04 6.27 11.54320DBB 4.25 5.88 15.21 8.25 13.68420DBB 4.50 5.88 17.38 10.31 15.84125DBB 3.88 7.50 12.07 3.50 10.57225DBB 3.88 7.56 14.38 7.00 12.88 325DBB 5.38 7.50 16.69 9.31 15.19 425DBB 5.88 7.50 19.00 12.00 17.50138DBB 6.00 11.00 16.25 5.00 14.25238DBB 7.38 11.00 19.05 9.00 17.05 338DBB 8.38 10.88 21.85 12.00 19.73 438DBB 9.06 10.88 24.65 5.00 22.52 Size Bore Range D D1 W4

Min. Max.

SI Dimensions in millimeters

109DBB 43 64 184 44 154209DBB 49 65 221 102 191309DBB 54 67 202 133 230115DBB 54 64 242 73 191215DBB 78 108 283 111 235120DBB 76 149 276 76 238 220DBB 95 152 331 159 292320DBB 108 149 386 210 347420DBB 114 149 441 262 402125DBB 99 191 307 89 268225DBB 99 192 365 178 327325DBB 137 191 424 236 386425DBB 149 191 483 305 445138DBB 152 279 413 127 362238DBB 187 279 484 229 433338DBB 213 276 555 305 501438DBB 230 276 626 381 572Size Bore Range D D1 W4

Min. Max.

Notes:

0.50 in (13mm) for 109 DB 0.25 in (6mm) for 209 DBB 0.00 in (0mm) for 309 DBB

Tolerance +0.000/-0.003 in (+0,00/-0,08 mm)

Tolerance +0.003/-0.000 in (+0,08/-0,00 mm)

American National Pipe Thread.

Brake in disengaged position.

All DBB brakes can be supplied plumbed as shown with a flow control valve having American National Pipe thread ports of 1/2-14 for size 9DBB, 3/4-14 for sizes 15DBB, 20 DBB, 25DBB and 1-11 1/2 for size 38DBB Tolerance +/- 0.12

Basic part number only. Does not include gear. Gear must be ordered separately with the bore and keyway requirements.

Dynamic torque shown. Static torque approximately 15% greater. Torque values are for new linings. Torque decreases with lining wear. At the worn out condition, torque is approximately 0.66 of values shown.

Torque ratings are for units with a standard complement of springs. Consult factory for torque ratings of units with non-standard spring configurations.



Maximum diameter of “as cast”surfaces.

Some high torque applications of three and four disc elements require additional support on the cylinder side of the unit. Contact your local Airflex representative for more details.

* Sizes 325 & 425 have 0.781" (19.8 mm) Mounting Hole

* 25DBB(12) 0.656 (16,7) Ø Mounting

holes equally spaced as shownon 28.750 (730,3) Bolt Circle

6°

15DBB(6) 0.656 (16,7) Ø Mounting

holes based on 8 equallyspaced holes on

30°

38DBB(16) 1.062 (27,0) Ø Mounting

holes equally spaced asshown on 42.000 (1066,8)

5°

9DBB(6) 0.531 (13,5) Ø Mounting

holes equally spaced asshown on 11.125 (282,5) Bolt

60°

20DBB(12) 0.656 (16,7) Ø Mounting

holes equally spaced asshown on 22.000 (558,8) Bolt

Mounting

Bolt Circles

5°


Airflex® DBB Brake ElementsDimensional and Technical Data

Section E

English lb in psi in3 in2 lbft2 lb rpm

109DBB 146333 415313 7500 60 30 96 0.5 9 115 3000209DBB 146334 415314 14000 60 30 192 1 18 145 3000309DBB 146380 416481 19400 60 30 238 1.83 27 135 3000115DBB 146222 415454 30000 60 75 238 5 35 225 2400215DBB 146337 415302 57000 60 75 476 10 64 275 2400120DBB 146299 415900 53500 60 133 334 17 40 385 1850220DBB 146300 416059 101500 60 133 668 33 67 487 1850320DBB 146378 416304 149500 60 133 1002 49 213 590 1850420DBB 146379 416471 180000 60 133 1336 65 102 695 1850125DBB 146315 416073 115300 60 259 600 47 78 705 1400225DBB 146327 416074 219000 60 259 1201 93 148 935 1400325DBB 146370 416223 303000 60 259 1802 139 403 1120 1400425DBB 146381 416477 392000 60 259 2403 185 280 1250 1400138DBB 146295 416068 420000 60 612 1322 287 203 1955 950238DBB 146296 416069 800000 60 612 2644 562 340 2325 950338DBB 146386 416241 1153000 60 612 3966 837 1087 3280 950438DBB 146387 416464 1470000 60 612 5288 1112 1424 3850 950 Gear Mr Minimum Disc Part Part Torque releasing Releasing Friction & Maximum Size Number Number rating pressure Volume Area Gear Housing speed

Wk2 Weight J Mass109DBB 146333 415313 847 4,1 0,49 619 0,02 4 52 3000209DBB 146334 415314 1581 4,1 0,49 1238 0,04 8 66 3000309DBB 146380 416481 2192 4,1 0,49 1857 0,07 12 36 3000115DBB 146222 415454 3387 4,1 1,23 1535 0,21 16 102 2400215DBB 146337 415302 6435 4,1 1,23 3070 0,42 29 125 2400120DBB 146299 415900 6040 4,1 2,18 2154 0,71 18 175 1850220DBB 146300 416059 11459 4,1 2,18 4309 1,39 30 221 1850320DBB 146378 416304 16879 4,1 2,18 6463 2,06 97 277 1850420DBB 146379 416471 20338 4,1 2,18 8617 2,73 46 315 1850125DBB 146315 416073 13017 4,1 4,25 3870 1,97 35 320 1400225DBB 146327 416074 24725 4,1 4,25 7746 3,91 67 424 1400325DBB 146370 416223 34237 4,1 4,25 11623 5,84 183 508 1400425DBB 146381 416477 44067 4,1 4,25 15499 7,77 127 567 1400138DBB 146295 416068 47418 4,1 10,03 8527 12,05 92 887 950238DBB 146296 416069 90320 4,1 10,03 17054 23,60 154 1055 950338DBB 146386 416241 130282 4,1 10,03 25581 35,15 493 1488 950438DBB 146387 416464 166101 4,1 10,03 34108 46,70 646 848 950SI nm bar dm3 cm 2 kgm 2 kg rpm

O2

See Note

J J1

D31

D

Single Disc Brake

J2

W4

H16D1

D45

D44

Dual Disc BrakeSee Note on

pg. E-7


Airflex® DBBS Component PartsSection E


1 Mounting Flange2 Stud3 Friction Disc4 Clamp Tube5 Pressure Plate6 Spring Housing7 Flat Washer8 Lock Nut9 Cylinder10 Hex Head Screw11 Inner Seal12 Spring13 Outer Seal14 Spacer Tube15 Gear16 Wear Spacer17 Reaction Plate18 Release Spring19 Spring Retainer20 Flat Head Screw21 Disc

19

9

6

517

11

18

12

8721416

2

15

20

10

131

3


14


J

J1

D31

Single Disc element

J2

D

D44

D45

D1

H16

Dual Disc element

J2

O2

25DBBS(12) 0.656 (16.7) Ø

Mounting holes equallyspaced as shown on28.750 (730,0) Bolt

Mounting Bolt Circles

6°

38 DBBS(16) 1.062 (27.0) Ø

Mounting holes equallyspaced as shown on

42.000 (1066.8) bolt circle

5°

20DBBS(12) 0.656 (16.7) Ø

Mounting holes equallyspaced as shown on22.000 (558.0) Bolt

5°

50 DBBS(16) 1.438 (36.5) Ø


54.000 (1371.6) bolt circle

4°

Airflex® DBBS Brake ElementsDimensional and Technical Data Section E


120DBBS 3.50 5.63 10.30 3.00220DBBS 4.25 5.69 13.48 6.27320DBBS 4.88 5.75 16.63 10.31420DBBS 5.13 5.81 19.81 12.50125DBBS 4.50 7.00 11.49 3.50225DBBS 5.50 7.13 14.73 7.00325DBBS 6.13 7.38 17.96 12.00425DBBS 6.63 7.31 21.19 15.00138DBBS 8.50 10.06 15.20 5.00238DBBS 8.50 10.06 18.97 9.00338DBBS 9.63 10.06 22.60 13.00438DBBS 10.38 10.38 26.34 18.00150DBBS 10.24 15.51 20.43 5.75250DBBS 12.36 15.51 24.84 10.00350DBBS 13.90 15.51 29.29 14.49450DBBS 14.88 15.51 35.24 20.00 Size Bore Range D D1

Min. Max.120DBBS 89 143 262 76 220DBBS 103 145 342 159320DBBS 124 146 422 262420DBBS 130 148 503 318125DBBS 114 177 292 89225DBBS 140 181 374 178325DBBS 156 187 456 381425DBBS 168 186 538 381138DBBS 216 256 386 127238DBBS 216 256 482 229338DBBS 245 256 574 330438DBBS 264 264 669 457150DBBS 260 394 519 146250DBBS 314 394 631 254350DBBS 353 394 744 368450DBBS 378 394 895 508SI Dimensions in millimeters


20DBBS 1.50 0.38 1.00 8.50 23.25 18.250 23.82 1/2-1425DBBS 1.75 0.25 1.00 11.50 30.63 24.375 30.89 1/2-1438DBBS 2.45 0.25 1.00 16.50 44.498 36.375 45.00 3/4-1450DBBS 3.50 0.25 2.00 23.00 46.25 57.64 1-11 1/2 Size D31 D44 D45 H16 J J1 J2 O2

20DBBS 38 10 25 216 590.6 463.5 605 1/2-1425DBBS 44 6 25 292 778.0 619.1 785 1/2-1438DBBS 62 6 25 419 1135.7 923.9 1143 3/4-14SI Dimensions in millimeters

Notes:

Brake in disengaged position.

Tolerance +0.000/-0.005 in (+0,00/-0,08 mm)

Tolerance +0.003/-0.000 in (+0,08/-0,00 mm)

Maximum diameter of “as cast”surfaces.

American National Pipe Thread.

Tolerance +.120/-.120 in (+3.00/-3.00 mm) * Sizes 325 and 425 have 0.781 (19.8) mounting holes

J

J1

D31

Single Disc element

J2

D

D44

D45

D1

H16

Dual Disc element

J2

O2

25DBBS(12) 0.656 (16.7) Ø

Mounting holes equallyspaced as shown on28.750 (730,0) Bolt

Mounting Bolt Circles

6°

38 DBBS(16) 1.062 (27.0) Ø


42.000 (1066.8) bolt circle

5°

20DBBS(12) 0.656 (16.7) Ø

Mounting holes equallyspaced as shown on22.000 (558.0) Bolt

5°

50 DBBS(16) 1.438 (36.5) Ø


54.000 (1371.6) bolt circle

4°

*


Airflex® DBBS Brake ElementsDimensional and Technical Data Section E

Worn Torque English lbin Multiplier psi in3 in2 lbft2 lb rpm

120DBBS 146323 415900 80,000 — 90 133 346 33 125 400 2200

220DBBS 146322 416059 150,000 — 90 133 692 65 232 550 2200

320DBBS 146373 416471 224,000 — 90 133 1,038 120 357 720 2200

420DBBS 146374 416472 220,000 — 90 133 1,384 159 464 914 2200

125DBBS 146320 416073 173,000 — 90 259 628 89 212 880 1700

225DBBS 146330 416074 325,000 — 90 259 1,255 178 416 1,318 1700

325DBBS 146382 416477 455,000 — 90 259 1,883 309 682 1,585 1700

425DBBS 146383 416470 585,000 — 90 259 2,510 411 854 1,882 1700

138DBBS 146328 416068 630,000 .81 90 612 1,357 553 583 2,125 950

238DBBS 146329 416069 1,200,000 .80 90 612 2,714 1,094 1,100 3,125 950

338DBBS 146384 416414 1,730,000 .80 90 612 4,071 1,709 1,680 4,085 950

438DBBS 146385 416461 2,200,000 .79 90 612 54,28 2,285 2,264 4,975 950

150DBBS 146524 417277 1 ,798,000 .81 120 1,115 2,111 1,682 1,071 5,872 600

250DBBS 146525 417278 3 ,284,000 .79 120 1,115 4,222 3,330 1,929 7,196 600

350DBBS 146526 417279 4 ,555,000 .77 120 1,115 6,333 4,895 2,738 8,685 600

450DBBS 146527 417280 5 ,578,000 .75 120 1,115 8,444 6,506 3,515 10,092 600 Gear Mr Worn Minimum Disc Part Part Torque Torque Releasing Releasing Friction & Maximum Size Number Number Rating Multiplier Pressure volume Area Gear Housing Speed

Wk2 Weight J Mass120DBBS 146323 415900 9.032 — 6,2 2,18 2.232 1,39 56 181 2200

220DBBS 146322 416059 16.935 — 6,2 2,18 4.465 2,74 105 249 2200

320DBBS 146373 416471 25.290 — 6,2 2,18 6,697 5,06 162 327 2200

420DBBS 146374 416472 24.839 — 6,2 2,18 8.930 6,70 211 415 2200

125DBBS 146320 416073 19.532 — 6,2 4,24 4.052 3,75 96 398 1700

225DBBS 146330 416074 36.693 — 6,2 4,24 8.097 7,50 188 596 1700

325DBBS 146382 416477 51.372 — 6,2 4,24 12.149 13,03 310 720 1700

425DBBS 146383 416470 66.049 — 6,2 4,24 16.194 17,34 388 855 1700

138DBBS 146328 416068 71.127 .81 6,2 10,02 8.755 23,30 264 962 950

238DBBS 146329 416069 135.480 .80 6,2 10,02 17.510 46,10 498 1.414 950

338DBBS 146384 416414 195.325 .80 6,2 10,02 26.265 72,10 736 1.856 950

438DBBS 146385 416461 248.391 .79 6,2 10,02 35.020 96,41 1.029 2.261 950

150DBBS 146524 417277 203,164 .81 8.3 18.3 13,619 70.88 486 2,663 600

250DBBS 146525 417278 371,073 .79 8.3 18.3 27,239 140.33 875 3,264 600

350DBBS 146526 417279 514,689 .77 8.3 18.3 40,858 206.28 1,242 3,939 600

450DBBS 146527 417280 630,282 .75 8.3 18.3 54,477 274.16 1,594 4,578 600SI Nm bar dm3 cm2 kgm2 kg rpm

Notes:

Basic part number only. Does not include gear. Gear must be ordered separately with bore and keyway requirements.

Dynamic torque shown. Static torque approximately 15% greater. Torque values are for new linings. Torque decreases with lining wear. At worn out condition, torque is approximately 0.66 of values shown, unless otherwise noted.

Torque ratings are for units with a standard complement of springs. Consult factory for torque ratings of units with non-standard spring

configurations.




Airflex® Type DC Element DescriptionSection E

Type DC elements can be used as either pressure actuated clutches or brakes. They are available in single and multiple disc designs.

Element construction and operation is illustrated in the figure. Pressurizing the cylinder causes the piston to clamp the friction disc assemblies between clamping plates. External springs ensure positive disengagement.

Type DC elements are available in five basic disc sizes with static torque ratings to 2,061,000 lb.in (233.000 N.m). Ele-ment sizes are indicated by the number of friction discs and by the disc diameter in inches. For instance, size 225DC has two friction discs 25 inches in diameter.

Features

Favorable torque to size ratio. DC type elements are physically smaller than most other type clutches and brakes with the same torque capacity.

Low inertia friction disc assembly. Reduces the overall inertia that must be started or stopped.

Optional split friction discs. Allows removal of friction discs without disturbing other com-ponents of drive system in mid-shaft element arrangement.

Long wearing, self lubricating PolyPak* seals. Eliminates premature twisting failure and requires no external lubrication.

Where used:

• Power Presses

• Tension Brakes

• Emergency Stop Brakes on Unwind Stands


Airflex® DC Component PartsSection E


1 Mounting Flange2 Stud3 Friction Disc Sub-Assembly4 Friction Disc5 Friction Disc Core6 Rivet7 Washer8 Clamp Tube9 Pressure Plate10 Flat Washer11 Locknut


12 Cylinder13 Inner Seal14 Outer Seal15 Gear16 Wear Spacer17 Reaction Plate18 Piston19 Release Spring20 Flat Washer21 Hex Head Screw22 Ring Gear

12

18

14

174

13

5

2

11109816

22

20, 21

15

6, 7

1

3


19


Airflex® Type DC ElementsTechnical Data

Section E

lbin English @ 75 psi rpm in3 in2 lbft2 lb

109DC 10500 3000 1600 4 24 96 8 0.5 60 9209DC 21000 3000 1600 7 30 192 9.5 1 70 18115DC 41000 2400 1050 9 60 238 55 5 170 35215DC 82000 2400 1050 17 70 476 65 10 190 64120DC 77000 1850 850 27 133 334 82 17 235 77220DC 154000 1850 850 53 160 668 104 33 297 145320DC 231000 1850 850 79 187 1002 126 49 359 213420DC 308000 1850 850 105 214 1336 148 66 421 281125DC 160000 1400 650 43 216 600 339 47 557 143225DC 320000 1400 650 86 259 1201 420 93 689 273325DC 480000 1400 650 129 302 1801 501 140 821 403425DC 640000 1400 650 172 345 2400 582 186 953 533138DC 560000 950 450 102 510 1322 2031 287 1568 413238DC 1120000 950 450 203 612 2644 2139 562 1651 750338DC 1680000 950 450 304 714 3966 2247 837 1734 1087438DC 2240000 950 450 405 816 5288 2355 1112 1817 1424 Mr Disc Disc Torque Maximum Engaging Friction & & Size Rating Speed Volume Area Housing Gear Housing Gear

Disc Element New Worn Wk2 Weight J Mass109DC 1190 3000 1600 0,07 0,39 619 0,34 0,02 27 4209DC 2370 3000 1600 0,11 0,49 1238 0,40 0,04 32 8115DC 4630 2400 1050 0,15 0,99 1535 2,32 0,21 77 16215DC 9260 2400 1050 0,28 1,15 3069 2,74 0,42 86 29120DC 8690 1850 850 0,44 2,18 2154 3,46 0,72 107 35220DC 17390 1850 850 0,87 2,63 4307 4,38 1,39 135 66320DC 26080 1850 850 1,30 3,07 6461 5,31 2,06 163 97420DC 34770 1850 850 1,72 3,52 8614 6,24 2,76 191 127125DC 18060 1400 650 0,71 3,55 3869 14,29 1,98 253 65225DC 36130 1400 650 1,41 4,25 7744 17,70 3,92 312 124325DC 54190 1400 650 2,12 4,96 11619 21,11 5,90 372 183425DC 72260 1400 650 2,83 5,67 15488 24,53 7,84 432 242138DC 63220 950 450 1,68 8,38 8524 85,59 12,09 711 187238DC 126450 950 450 3,33 10,05 17048 90,14 23,68 749 340338DC 189670 950 450 4,99 11,73 25572 94,69 35,27 786 493438DC 252900 950 450 6,65 13,41 34097 99,24 46,86 824 646 Nm SI @ 5,2 bar rpm dm3 cm 2 kgm 2 kg

25DC

25°

(12) 0.656 (16.7) Ø MountingHoles Equally Spaced as

Shown on 28.750 (730.3) Bolt

9DC

45°


Shown on 11.125 (282.5) BoltCircle

Mounting BoltCircles

15DC

13°

(6) 0.656 (16.7) Ø MountingHoles Based on 8 Equally

Spaced as Shown on 17.500(444.5) Bolt Circle

20DC

25°


Shown on 22.000 (558.8) Bolt

38DBC(16) 1.062 (27.0) Ø Mounting

Holes Equally Spaced asShown on 42.000 (1066.8) Bolt

Circle

18.75

Notes:

Dynamic torque shown. Static torque 15% greater. Maximum allowable pressure 120 psi (8,3 bar).

Absolute cylinder volume with new or worn friction linings.

Based upon minimum bore.

Basic part number only. Gear not included.

Tolerance +0.000/-0.003 in (+0,00/-0,08 mm)

Tolerance +0.003/-0.000 in (+0,08/-0,00 mm)

Maximum diameter of ”as cast“ surfaces.

American National Pipe Thread

Some high torque applications of three and four disc elements require additional sup port on the cylinder side of the unit. Contact your local Airflex representative for more details.


Airflex® Type DC ElementsDimensional Data Section E


109DC 146239 415313 1.75 2.38 1.75 5.63 0.25209DC 146240 415510 1.88 2.38 3.25 7.63 0.25115DC 146225 415454 2.75 3.98 2.88 7.00 0.38215DC 146226 415454 3.44 3.94 4.38 9.00 0.38120DC 146301 415900 3.31 5.63 3.00 8.00 0.75220DC 146317 415959 4.25 5.69 5.63 11.50 0.00320DC 146366 416304 4.88 5.56 8.25 14.63 0.00420DC 146390 416472 5.38 5.69 12.50 16.25 0.00125DC 146316 416073 4.38 7.13 3.50 9.50 0.75225DC 146355 416074 5.50 7.13 7.00 12.00 0.38325DC 146354 416623 6.25 6.88 9.31 14.50 0.00425DC 146389 416477 6.25 6.88 12.00 18.00 0.00138DC 146307 416068 6.75 10.50 5.00 13.50 1.25238DC 146336 416069 8.50 10.25 9.00 16.50 0.00338DC 146360 416241 9.25 9.75 13.00 19.50 0.00438DC 416388 416461 8.50 10.25 18.00 25.00 0.00

Min. Max. Gear Part Part Bore Size Number Number Range D1 W4 D46

SI Dimensions in millimeters

109DC 146239 415313 44 60 44 143 6209DC 146240 415510 48 60 83 194 6115DC 146225 415454 70 98 73 178 10215DC 146226 415454 87 100 111 229 10120DC 146301 415900 97 143 76 203 19220DC 146317 415901 108 143 143 292 0320DC 146366 416304 124 141 210 372 0420DC 146390 416374 137 145 277 413 0125DC 146316 416073 111 181 89 241 19225DC 146355 416074 140 181 178 305 10325DC 146354 416623 159 175 236 368 0425DC 146389 416477 159 175 305 457 0138DC 146307 416068 171 267 127 343 32238DC 146336 416069 216 260 229 419 0338DC 146360 416241 235 248 330 495 0438DC 146388 416461 216 260 457 635 0

Min. Max. Gear Part Part Bore Size Number Number Range D1 W4 D46

W4

D44

J

D46J2

D1

H

O2

J1

D31

H16

See Note onpg. E-14


9DC 1.00 0.25 3.25 3 1/4-20NC-2 3.50 12.125 8.375 12.37 3/8-1415DC 1.47 0.38 6.00 3 3/8-16NC-2 6.50 18.375 14.375 18.94 1/2-1420DC 1.50 0.38 8.50 3 3/8-16NC-2 9.13 23.250 18.250 23.82 1/2-1425DC 1.75 0.25 11.50 4 3/8-16NC-2 12.25 30.630 24.375 30.58 1/2-1438DC 2.45 0.25 16.50 4 1/2-13NC-2 17.50 44.750 36.375 44.86 3/4-14 Size D31 D44 H16 H J J1 J2 O2

No. Size Bolt Circle9DC 25 6 83 3 1/4-20NC-2 89 308,0 212,7 314 3/8-1415DC 37 10 152 3 3/8-16NC-2 165 466,7 365,1 481 1/2-1420DC 38 10 216 3 3/8-16NC-2 232 590,6 463,5 605 1/2-1425DC 44 6 292 4 3/8-16NC-2 311 778,0 619,1 777 1/2-1438DC 62 6 419 4 1/2-13NC-2 445 1136,7 923,9 1139 3/4-14SI Dimensions in millimeters

Notes are on page E - 14


Airflex® FHB Brake Elements Section E

Overview

Eaton Airflex has introduced a revolutionary new design in disc brake technology called the Floating Housing Brake (FHB). The spring applied (power off), air-cooled disc brake is well suited for applications in Surface Mining, Oilfield and other heavy-duty industrial machinery designs.

The FHB is an air cooled spring applied brake with exceptional friction life and rapid friction replacement capability. It is sup-plied with long wearing, organic friction material and a rugged solid cast, rotating disc that provides lower inertia than typical caliper brakes.

Features

• Ratedforover430,000lb-inoftorque

• Patentedbrakingconceptusesafloatinghousinginsteadof a floating rotor

•Multiplebrakeinstallationdesignsexistforindustryleading motors

• Fixedhubandrotordesign

Benefits

• Abilitytoquicklychangethefrictionpadsreducesdown time on dragline from 3 hours to 1 hour

• Reducedmaintenancecostwitheliminationofsplinetooth or gear wear

• Longerfrictionpadwearlifeduetoafull360°annulardisc

• Fasterandsaferinstallationwithexclusiveshaftlock assembly for ease of mounting and removal

• Virtuallynowearduringfreewheeling,allowshighproduct life



Technical Introduction

The FHB brake is offered for applications with non-cyclic brake engagement that require higher speed operation or pre-cise balance of the rotating components is required. It uses a solid rotor and stationary friction material to develop equal torque in either direction of rotation. The disc is mounted on the shaft which is to be stopped while the brake assembly is attached to the machine frame. Pressurizing the brake compresses the brake springs and withdraws the clamping force from the brake disc so the shaft can rotate freely. As air pressure is exhausted, the springs force the pressure plate towards the mounting flange and the spring housing which in turn forces the floating plate away from the mounting flange, clamping the disc and the friction pad assembly.

Typical Applications

Draglines Electric Shovels Winches

Hoist HoistDrag CrowdSwing SwingPropel (Walk) Propel

lb-in N-m in. mm. in. mm.138FHB 36 432,900 48,918 950 18.24 463.3 18.48 469.39

*Dynamic torque calculated based on 36 sets of springs, static torque is approximately 15% more. Torque in each application is dependent on number of spring sets.

SizeNo. of Spring

Sets

Dynamic Torque* Max RPM

Length EngagedLength

Released




Item Qty. Description Part Number

*2 1 Mounting Flang 515532 3 1 Floating Plate 515503*4 1 Disc 515536 5 1 Pressure Plate 515505 6 1 Spring Housing 515507 7 1 Cylinder 515509 *8 1 B-Loc 417385-02 9 16 Friction Linning S/A 308589 10 16 Flanged Bolt 308602 11 16 Metric Shoulder Screw 308593 12 8 Main Stud 308601-01 13 8 Clamp Tube 308586-01 14 8 Support Stud 308592-01 15 8 Spacer 308590-01 16 8 Plain Washer 000067X0063


Item Qty. Description Part Number

17 8 Nut 000414X0013 18 4 Return Spring 416751-04 19 8 Plain Washer 000067X0065 20 8 Nut 000414X0004 21 2 Lip Seal 000402X0005 22 2 Lip Seal 000402X0006 **23 36 Inner Apply Spring 416751-08 **24 36 Outer Apply Spring 416751-07 25 12 Spring Retainer 415635 26 8 FP Bush 204214-01 27 8 PP Bush 204214-02 28 8 SH Bush 204214-03 29 8 Power Head Spacer 308599-01 30 8 Plain Washer 000067X0064 31 8 Screw 000391X3602

*Part number may vary - depending on application **Quantity may vary - depending on application requirements


Airflex® FHB Brake Elements 138FHB Specifications and Dimensions Illustrated Section E

*

21

52.5

* Consult factory for alternate mounting options.


Airflex® Brake Selection ProcedureSection E

Torque and Thermal Capacities General

Technical Section Y of the catalog contains useful information pertaining to the selection, mounting, alignment and control of clutches and brakes in general. Formulas, symbols and units are also identified. It is recommended that Section Y be reviewed before attempting to size a specific product for an application.

Torque

DBA and DBB Brakes The torque ratings are dependent upon spring force and quantity, not a pressurizing medium. However, a pressurizing medium is required to compress the springs to release the brake. Minimum releasing pressures, as well as the maxi-mum pressures which the piston and cylinder can withstand, are given on the catalog pages.

Type DBA and DBB brakes are disc type and develop equal torque in both directions of rotation. Several springs are used in their design. If brake size is determined by thermal require-ments rather than torque requirements, brake torque can be reduced by spring removal.

For spring applied brakes, torque will decrease with lining wear, due to the longer piston travel required for engage-ment. Single disc DBA and DBB brakes have no provision for adjustment. Multiple disc brakes have a provision for adjust-ment after a given amount of lining wear. Therefore, DBA and DBB brake torque with worn linings must be considered in the selection process.

DC Elements

DC element dynamic torque ratings Mr, are based on an effective pressure pr of 75 psi (5,2 bar). Maximum allowable operating pressure is 120 psi (8,3 bar). Torque ratings must be adjusted for operating pressure po and parasitic loss pp.

The elements have an inherent parasitic pressure pp, required to cause friction disc engagement, which represents the pressure to overcome internal sliding friction and to compress disc releasing springs.

Element torque is calculated from:

Cyclic and Non-Cyclic Thermal Capacity

Brake types DBAV and DBB were designed for cyclic stop-ping applications. They are capable of a maximum thermal capacity Pc of 0.012 HP/in2.

Non-cyclic thermal capacity is determined by the element's friction area, drum or disc mass, material heat capacity and thermal conductivity. The properties of our standard elements result in the limits indicated in the Non-Cyclic Energy Capacity Graph. An explanation on the use of this graph follows.

The thermal energy calculated for the load is adjusted to include the energy associated with accelerating or deceler-ating the components of the tentative clutch and/or brake selection. The adjusted thermal energy Wt is divided by the element's friction area A. Next, the average power loading Pave is calculated from:

The point (Wt/A, Pave) is plotted on the graph. If the point falls below the appropriate product limit line, the selection will handle the load. If it does not, an element having a greater friction area is required.

No. of Friction Discs Pressure pp

psi bar1 3 0,212 4 0,283 5 0,344 6 0,41

rr

poe M

p

ppM ⋅

−=

AP

P tave =


Airflex® Selection ProcedureSection E

Non-Cylic Energy CapacityPave (HP/in2)

W1/A

(ft·lb

/in2 )

Pave (kW/cm2)

W1/A

(joul

e/cm

2 )

Example

A cyclic stopping brake is required for use on a power press operating under the following conditions. Determine the brake size and allowable cyclic rate.

Brake shaft speed: 300 rpm

Stoppingangleatcrankshaft:15°

Inertia referred to brake shaft: 750 lb·ft2

Press stroke: 10 in

Ram and die weight: 2500 lb

Reduction between brake shaft and crankshaft: 10:1

Stopping angle at brake shaft 0d =15°·10=150°

= 51,700 lb·in

Reverse brake torque required =

0.5·stroke·weight/reduction

= 0.5·10·2500/10

= 1250 lb·in

From required torques, select 215DBB

Lining area = 476 in2

Disc and gear WK2 = 10 lb·ft2

Total WK2 = 750 + 10 = 760 lb·ft2

= 11650 ft·lb

= 16

5873300760

5873nk W

W222 ⋅

=⋅

=

W33000P

cpm

33000cpm W

P

c

c

⋅=

⋅=

1165033000 4760.012 ⋅⋅

=

0.1725.58300750

t25.58nkW

b M

0.17sec.3003

150n3d 0

t

d

2

0

d

⋅⋅

=⋅⋅

=

=⋅

=⋅

=

Documents

Airflex® Air Cooled Disc Clutches and Brakes Cooled Disc Clutches an… · EATON Airflex® Clutches & Brakes 10M1297GP November 2012 181 Airflex® DBA Description Section E Model