AII31723 FIT Fog lights - · PDF file© 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 31723 (0603) 1 of 13 PARTS LIST 08V31-SLN-3000-93 ... How to Operate Fog Lights

© 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 31723 (0603) 1 of 13

PARTS LIST

08V31-SLN-3000-93

INSTALLATIONINSTRUCTIONS

Accessory Application Publications No.

Issue Date

MAR 2006

2007 FITFOG LIGHTS

Fog light assembly (right)

Fog light assembly (left)

Fog light harness

Switch harness

Fuse label

Relay

2 Clip nuts

2 Special screws

11 Wire ties

Fog light subharness

2 Wire ties with clips

Fuse (20A)

Template

Fog light switch

Wire tie with holder

2 Clips

AII 31723

2 of 13 AII 31723 (0603) © 2006 American Honda Motor Co., Inc. - All Rights Reserved.

TOOLS REQUIRED

Phillips screwdriver

Flat-tip screwdriver

Ratchet wrench (8 mm, 10 mm box)

Drill

Drill bits (3 mm, 5.5 mm)

Utility knife

File

Hacksaw blade

Felt-tip pen

Hole saw (20 mm)

Shop towel

Isopropyl alcohol

Pushpin

Eye protection

Scissors

Blanket

Masking Tape

Illustration of the Fog Lights Installed on theVehicle

5804010T

SELF-TAPPINGSCREWS (4)

FRONTBUMPER

CLIPS (8)

INSTALLATION

Customer information: The information in thisinstallation instruction is intended for use only byskilled technicians who have the proper tools,equipment, and training to correctly and safely addequipment to your vehicle. These proceduresshould not be attempted by “do-it-yourselfers”.

NOTE: Be extremely careful not to damage the frontbumper or any other finished surfaces of the body.

1. Make sure you have the anti-theft code for theradio, then write down the frequencies for thepreset buttons.

2. Disconnect the negative cable from the battery.

Cutting the Front Bumper

3. Open the hood. Remove the front bumper (eightclips and four self-tapping screws). To preventdamage, set the front bumper on a blanket.

NOTE: Have an assistant help you when removingand installing the front bumper.

5922070H

FUSE

FOG LIGHTASSEMBLY(Right)

RELAY

FOG LIGHTHARNESS

FUSE BOX

SWITCHHARNESS

SWITCH

FOG LIGHTASSEMBLY(Left)

FOG LIGHTSUBHARNESS


4. Remove the left front bumper side vent (threehooks).

6. On the outside of the front bumper, place the lefttemplate along the front bumper and tape it inplace.

5. Using scissors, cut out the template marked “L”along the outer line as shown.

5919020H

TEMPLATE

“L” MARK

7. Using a pushpin, mark the front bumper at eachof the six marks printed on the template.

8. Using a utility knife, cut the template along thebroken lines.

9. Using a felt-tip pen, mark the front bumper alongthe outer edge of the template. Remove thetemplate.

5919030H

FRONTBUMPER

FRONT BUMPERSIDE VENT(Reuse in step 27.)

HOOKS(3)

5919043HPUSHPINAlign with thefront bumper.

MASKING TAPE

TEMPLATE “L”

MARKS (6)

Put two tabsinto the squareholes.

SQUARE HOLES (2)

5D06011H

Cut the templatealong its broken lines.

TEMPLATE “L”

FELT-TIPPEN

UTILITYKNIFE


13. Locate the dimple on the front bumper. Whilewearing eye protection, drill a 5.5 mm hole throughthe dimple. Start with a 3 mm drill bit, and finishwith a 5.5 mm drill bit.

11. While wearing eye protection, drill six 20 mmholes through the marks you just made.

12. Using a hacksaw blade, cut the bumper along theline made in step 9. Use care when cutting thebumper along the outer line. Remove any burrsfrom the edge of the hole with a file.

10. To protect the front bumper, apply masking tape inthe area shown.

14. Repeat steps 4 through 13 to mark and cut theright side of the bumper.

Routing the Fog Light Subharness

15. Remove the left inner fender clip. Pull the left innerfender down; releasing a tab in the directionshown.

5919052H

HOLESAW(First drill with a 3 mmbit, and finish with a 20mm bit or holesaw.)

MASKING TAPE

PUSHPINMARKS (6)

FRONTBUMPER

5919070H

DIMPLE

DRILL(3 mm 5.5 mm bit)

MASKING TAPE

10 mm

MASKING TAPE

5030010H

TAB

INNERFENDER

Pull down.

CLIP

5919062H

HACKSAW(Be extremely carefulnot to cut the bumpermore than necessary.)

Cut along the line.


16. Inside the left fender area, locate the 1-pinconnector blue-taped to the vehicle harness.Remove the blue tape to free the connector.

17. Plug the fog light subharness 1-pin connector intothe 1-pin connector you just freed, then route thefog light subharness along the vehicle harness tothe front of the vehicle.

18. Locate and remove the ground bolt from the leftinner fender area, then secure the fog lightsubharness ground terminal using the ground bolt.

19. Secure the fog light subharness to the vehicleframe and panel hole using the two wire ties withclips at the green-taped locations.

20. Secure the fog light subharness to the vehicleharness with three wire ties.

5919091H

FOG LIGHTSUBHARNESS

BLUE TAPE(Remove.)

FOG LIGHTSUBHARNESS1-PIN CONNECTOR

VEHICLE1-PINCONNECTOR

VEHICLEHARNESS

VEHICLEHARNESS

5920021H

FOG LIGHTSUBHARNESS

WIRE TIEWITH CLIP

GREENTAPE

GREENTAPE

WIRE TIEWITH CLIP

FRAME HOLE

FRAME HOLE

5919102H

FOG LIGHTSUBHARNESS

WIRETIE

5920010H

FOG LIGHTSUBHARNESSGROUND TERMINAL

FOG LIGHTSUBHARNESS

FRAME

VEHICLEGROUND BOLT(Reuse.)


24. Route the fog light harness along the front bumperto the right side of the vehicle and attach the fivefog light harness clips to the five ribs inside thefront bumper.

25. Route the narrowed portion of the fog light harnessto the right side of the front bumper, the same asin step 21.

26. Attach one clip to the fog light harness at thegreen tape, then secure the clip to the frontbumper opening as shown.

Routing the Fog Light Harness

21. On the inside of the front bumper on the left side,place the narrowed portion of the fog light harnessbetween the air screen and the front bumper.

22. Attach the wire tie with holder to the fog lightharness 4-pin connector, and route it through theair screen holes.

23. Attach one clip to the fog light harness at thegreen tape, then attach the clip to the frontbumper opening as shown.

5920032H

FOG LIGHTHARNESS

LEFT SIDE OFFRONTBUMPER

AIRSCREEN

FOG LIGHTHARNESS 4-PINCONNECTOR

WIRE TIEWITHHOLDER

AIR SCREENHOLE

NARROWEDPORTION

5920040H

CLIPFRONTBUMPEROPENING

FOG LIGHTHARNESS

GREENTAPE

5N29040H

CLIP FRONTBUMPEROPENING

FOG LIGHTHARNESS

GREENTAPE

5920052H

AIRSCREEN

FOGLIGHTHARNESS

FOG LIGHTHARNESS

AIRSCREEN

BUMPERGRILLERIB NARROWED

PORTION

CLIPS (5)


Routing the Switch Harness

33. Remove the driver’s dashboard under cover:

• Turn the knob clockwise.

• Release the clip and the pin.

34. Pull away the weatherstrip from around thedriver’s kick panel. Remove the driver’s kick panel(two clips).

32. Reinstall the front bumper.

27. Reinstall the front bumper side vents.

31. While holding the front bumper near the front ofthe vehicle, plug the fog light subharness 4-pinconnector into the fog light harness 4-pinconnector.

28. Attach one clip nut to the 5.5 mm hole made instep 13. Plug the fog light harness 2-pinconnecter to the left fog light.

29. Mount the fog light assembly to the front bumperby inserting the retaining tab around the bumper,and installing the self-tapping screw.

30. Install the right fog light assembly the same way.

5919082H

SPECIALSCREW

LEFT FOG LIGHTASSEMBLY

CLIP NUT

RETAINING TAB

FOG LIGHTHARNESS2-PINCONNECTOR

FRONT BUMPERSIDE VENT

5914010K

PINCLIP

KNOB

DRIVER’SDASHBOARDUNDER COVER

5914020K

WEATHERSTRIP

CLIPS (2)

DRIVER’SKICKPANEL

5030020H

FOG LIGHTSUBHARNESS4-PINCONNECTOR

FOG LIGHTHARNESS 4-PINCONNECTOR

FRONTBUMPER


38. Plug the 4-pin relay into the switch harness relayblock, then slide the relay block onto the vehiclerelay block on the right side of the fuse box.

39. Plug the switch harness 5-pin connector into the5-pin slot of the fuse box.

NOTE: If the fuse box 5-pin connector is alreadyused by another accessory:

Locate the 5-pin connector black-taped to theswitch harness, and remove the dummyconnector from the 5-pin connector. Plug theother accessory 5-pin connector into the switchharness 5-pin connector (black-taped).

35. Remove the fuse box cover:

• Turn the knob counterclockwise.

• Release the five clips and the three retainingtabs.

36. Using isopropyl alcohol on a shop towel,thoroughly clean the vehicle fuse label on theback of the fuse box cover.

37. Remove the adhesive backing from the fuse label,and then attach the fuse label over the existingvehicle fuse label as shown.

5914030KKNOB

CLIPS (5)

RETAINING TABS (3)

FUSE BOXCOVER

5921022H

SWITCHHARNESS

VEHICLEHARNESSFUSE BOX

4-PIN RELAY

SWITCH HARNESSRELAY BLOCK

5-PINCONNECTOR

Front View

5920800K

FUSE BOXCOVER

FUSELABEL

ADHESIVEBACKINGVEHICLE FUSE LABEL

(Thoroughly clean withisopropyl alcohol.)

5N03201H

ANOTHER ACCESSORY HARNESS5-PIN CONNECTOR

DUMMYCONNECTOR(Discard.)

SWITCH HARNESS5-PIN CONNECTOR

BLACK TAPE

5-PINCONNECTOR


41. Secure the switch harness to the vehicle harnesswith three wire ties.

42. From behind the dashboard, push out the switchcover from the switch panel, then unplug the13-pin connector from the mirror switch.

40. Install the 20A fuse into the number 20 slot in thefuse box.

43. Plug the switch harness 13-pin connector intothe mirror switch. Plug the vehicle mirror switch13-pin connector into the switch harness 13-pinconnector.

44. Get the fog light switch. Plug the switch harness5-pin connector into the fog light switch, theninstall the switch into the dashboard panel.

45. Secure the switch harness to the vehicle harnesswith one wire tie.

5921040H

SWITCH COVER(Discard.)


MIRRORSWITCH

SWITCHPANEL

TABS (2)

5921031H

SWITCHHARNESS

WIRE TIES (3)

VEHICLEHARNESS

FUSE BOX

FUSE LOCATION(Number 20 slot)

20A FUSE

Front View

5921051H


MIRRORSWITCH

SWITCHHARNESS13-PINCONNECTOR


5921060H

FOG LIGHT SWITCH


WIRE TIE

VEHICLEHARNESS

SWITCHHARNESS


49. Secure the 20-pin connector to the vehicleharness using two wire ties connected together.

50. Secure the 2-pin connector to the vehicleharness with one wire tie.

46. Unplug the vehicle 20-pin connector from the lowerleft side of the fuse box, and plug the switchharness 20-pin connector into the fuse box.

47. Plug the vehicle 20-pin connector you justunplugged into the remaining switch harness20-pin connector.

48. Locate the 2-pin connector blue taped to thevehicle harness. Remove the blue tape to free theconnector. Plug the switch harness 2-pinconnector into the 2-pin connector you just freed.

5921071H

VEHICLE 20-PINCONNECTOR

Front ViewSWITCHHARNESS20-PINCONNECTOR

FUSE BOX

5922011H

2-PINCONNECTORS

20-PIN CONNECTORS

WIRETIE

TWO WIRE TIES(Connect as shown.)

5921081H


VEHICLE 2-PINCONNECTOR

FUSEBOX

BLUE TAPE(Remove.)


USE AND CARE

How to Operate Fog Lights

NOTE: The fog light lenses can cloud when the outsidetemperature is cold; this is normal and should go awayin warm weather.

• Turn the light switch to the “ ” position (headlightson low beam).

• Press the fog light switch (indicator on).

• If the fog lights don’t come on, check the fuse andall the connectors, including the ground cable.

Fog Light Aiming Adjustment

• Adjust the aiming according to local laws andregulations.

• To adjust, turn the aiming adjustment screw in orout until the correct aiming is obtained.

51. Check that all wire harnesses are routed properlyand all connectors are plugged in.

52. Reinstall all removed parts. Check that all clipsand fasteners are installed securely.

53. Reconnect the negative cable to the battery.

54. Reset the clock, and reset the radio stationpresets.

NOTE: When the battery is disconnected, the driver’swindow AUTO function is disabled.

• Start the engine. Push down on the driver’swindow switch until the window is fully open.

• Pull up on the driver’s window switch to close thewindow completely, then hold the switch for 2seconds or more.

• Lower and raise the driver’s window to checkoperation of the driver’s window AUTO function.

5922050H

To lower.

To raise.

Lower View


4. Install the new bulb and socket to the fog light.

• Use only a genuine Honda halogen light bulbof specified wattage.

Rating: 12V 55W H11 Halogen Light Bulb P/N33165-S5A-003

• Do not touch the bulb. Oily or greasysubstances on the bulb can shorten its servicelife due to the heat produced when the bulb isturned on. If the bulb is accidentally touched,wipe it clean with a soft cloth that has beendampened with a denatured alcohol or a milddetergent solution.

• Align the tab on the fog light with the cutout inthe bulb when installing the new bulb. If notaligned, the fog light may annoy oncomingdrivers.

5. Reinstall the removed parts in the reverse order ofremoval.

• Check that the wire harnesses are notpinched.

• Be sure to tighten the self-tapping screw andbolts securely.

6. Check the operation of the fog light; adjust theaiming if necessary.

BULB REPLACEMENT

1. Remove a self-tapping screw and a clip, and thenpull back the inner fender.

2. Unplug the connector from the fog light.

3. Remove the bulb.

5908080TSELF-TAPPINGSCREW

CLIP

5922030H

FOG LIGHT

CONNECTORBULB

5922020H

FOG LIGHT

CONNECTORBULB


5922061H

BLK BRN BROWNBLACK

YEL ORN ORANGEYELLOW

BLU PUR PURPLEBLUE

GRN NAT NATURALGREEN

RED PNK PINKRED

WHT GRY GRAYWHITE

LT BLU LT GRN LIGHT GREENLIGHT BLUE

UNDER-HOODFUSE/RELAY BOX

BATTERYNo.1 (80A) No.7 (30A)

UNDER-DASHFUSE/RELAY BOX

BLU/RED

No.20 (20A)

WHT/RED

RED/YEL

HOT WITH HEADLIGHTSWITCH IN HEAD

No. 22 (10A FUSE)(In the under-dashfuse/relay box)

RED/BLK

BLU/YEL

FRONTFOG LIGHTRELAY

BLU/RED

BLK

LEFTFRONTFOGLIGHT

RIGHT

COMBINATIONLIGHT SWITCHDIMMER LOW

RED/WHT

RED

RED

DASH LIGHTBRIGHTNESSCONTROLLER(In the gaugeassembly )

LIGHTINDICATORLIGHT

HEADLIGHT SWITCH

Low HiOFF

ONFO

G L

IGH

TS

WIT

CH OFF - - - -

- - -

Documents

AII31723 FIT Fog lights - · PDF file© 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 31723 (0603) 1 of 13 PARTS LIST 08V31-SLN-3000-93 ... How to Operate Fog Lights