INSTALLATION AII 40101 INSTRUCTIONS 2-DOOR · AII 40101 (0808) 08V31-SVA-1F00-91 1 of 13 AII 40101 FOG LIGHTS 2009-2010 CIVIC 2-DOOR (EX-L) AUG 2008 PARTS LIST Right fog light Left

Publications No.

INSTALLATIONINSTRUCTIONS

Accessory Application

© 2008 American Honda Motor Co., Inc. – All Rights Re

AII 40101
FOG LIGHTS
served. AII 40101 (0808

2009-2010 CIVIC2-DOOR (EX-L)

) 0

Issue Date

AUG 2008

PARTS LISTRight fog light

Left fog light

Switch harness

Fog light harness

Sub harness

Switch

14 Wire ties

Wire tie with holder

4 Spring nuts

4 Self-tapping screws

20 A fuse(Some may not be used.)

Relay

TOOLS AND SUPPLIES REQUIREDPhillips screwdriverFlat-tip screwdriverRatchet10 mm SocketGlovesBlanketDiagonal cutters5 mm Hex wrenchShop towelMasking tape

1 of 138V31-SVA-1F00-91

Illustration of the Fog Lights Installed on the Vehicle

852201AK

SUB HARNESS

SWITCH HARNESS SWITCH

RELAY

RIGHT FOG LIGHT

FOG LIGHT HARNESS

LEFTFOG LIGHT

20 A FUSE

2 of 13 AII 40101

INSTALLATION

1. Make sure you have the anti-theft codes for the audio system, then write down the radio presets.

2. Disconnect the negative cable from the battery.

3. Remove the radiator cover (two expansion clips and two clips).

Customer Information: The information in thisinstallation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”

5311021T

2 CLIPS(Pull vertically.)

RADIATOR COVER

EXPANSION CLIP

PANEL

(0808) © 2008 American Honda Motor Co., Inc. – All Rights Reserved.

4. With the help of an assistant, remove the front bumper (six clips, two self-tapping screws, two socket bolts and two bumper bolts). To prevent damage, set the front bumper on a blanket.

5. Remove the left fog light cover (five pawls).

851308AK

6 CLIPS

FRONT BUMPER

2 SELF-TAPPING SCREWS

2 SOCKET BOLTS

2 BUMPER BOLTS

840801AK

LEFT FOG LIGHT COVER

5 PAWLS

FRONT BUMPER

© 2008 American Honda Motor Co., Inc. – All Rights Reserved. AII 40101

6. Install the two spring nuts onto the front bumper.

7. Install the left fog light to the fog light cover opening, and secure it with two self-tapping screws.

8. Repeat steps 5 through 7 on the other side.

9. Route the fog light harness 2-pin connector between the lower grille and the front bumper from the right side through the left side.

851303AK 2 SELF-TAPPING SCREWS

FRONT BUMPER

FRONT BUMPER

2 SPRING NUTS

LEFTFOG LIGHT

851304AK

FRONT BUMPER

FOG LIGHT HARNESS 2-PIN CONNECTOR

FOG LIGHTHARNESS2-PIN/4-PINCONNECTORS

FRONT BUMPER

FOG LIGHT HARNESS

LOWER GRILLE

(0808) 3 of 13

10. Plug the fog light harness 2-pin connector into the left fog light connector.

11. Install the fog light harness clip onto the lower grille rib.

12. Plug the fog light harness 2-pin connector into the right fog light connector.

13. Install the fog light harness clip onto the lower grille rib.

851305AK

FOG LIGHT HARNESS2-PIN CONNECTOR

LEFT FOG LIGHT CONNECTOR

LOWER GRILLE RIB

FOG LIGHT HARNESS CLIP

851306AK LOWER GRILLE RIB

FOG LIGHT HARNESS2-PINCONNECTOR

RIGHTFOG LIGHTCONNECTOR

FOG LIGHT HARNESS CLIP

4 of 13 AII 40101

14. Secure the fog light harness to each rib of the lower grille with one wire tie.

15. Remove three bolts from the washer tank.

851307AK

FOG LIGHT HARNESS

LOWER GRILLE

2 WIRE TIES

FOG LIGHT HARNESS

FOG LIGHT HARNESS

852101AK

3 BOLTSWASHER TANK


16. Remove the vehicle ground bolt, and reinstall it to the vehicle ground terminal with the sub harness ground terminal as shown.

17. Reinstall the washer tank. Check that the pipe of the washer tank is installed securely.

852102AK

SUBHARNESSGROUND TERMINAL

VEHICLE GROUNDTERMINAL

SUB HARNESS

VEHICLE GROUND BOLT(Reuse.)

PIPE


18. Locate the vehicle 1-pin connector blue-taped to the vehicle harness and remove the blue tape to free the connector. Plug the vehicle 1-pin connector into the sub harness 1-pin connector.

19. Route the sub harness as shown and secure it to the vehicle harness using three wire ties.

20. Install the wire tie with holder on the sub harness 4-pin connector.

21. Secure the wire tie with holder to the vehicle harness.

852103AK

FRONT

VEHICLE HARNESS

SUBHARNESS

VEHICLE1-PIN CONNECTOR

BLUE TAPE(Remove.)

SUB HARNESS1-PIN CONNECTOR

842802AK

3 WIRE TIES

WIRE TIE WITH HOLDER

VEHICLE HARNESS

FRONTSUB HARNESS4-PIN CONNECTOR

(0808) 5 of 13

22. Plug the fog light harness 4-pin connector into the sub harness 4-pin connector.

23. Reinstall the front bumper.

24. Remove the cover from the trunk lid/fuel fill door opener (six retaining tabs), and remove one self-tapping screw.

25. Using the key, unlock the opener.

852202AK

SUB HARNESS4-PIN CONNECTOR

FRONT BUMPERFOG LIGHT HARNESS

4-PIN CONNECTOR

5202191T

OPENER LOCK CYLINDER

KEY

SELF-TAPPING SCREW

COVER 6 RETAINING TABS

TRUNK LID/FUEL FILL DOOR OPENER

6 of 13 AII 40101

26. Raise the front side of the left front door sill trim (six clips, retaining tab and hook).

27. Remove the footrest.• Using a hex wrench, remove the lower clip from

the stud bolt.• Using a flat-tip screwdriver, remove the upper

clip from the stud bolt.

5311351T

RETAINING TAB

HOOK

FRONT

6 CLIPS

LEFT FRONT DOOR SILL TRIM

5311370T

HEX WRENCH

STUD BOLT

UPPER CLIP

LOWER CLIP

FOOTREST


28. Pull away the weatherstrip from the left kick panel and remove the left kick panel (two clips).

29. Remove the driver’s dashboard under cover (turn the lock knob 90° counterclockwise, and release the two clips and pin).

5202220T

WEATHERSTRIP2 CLIPS

LEFT KICK PANEL

5202112T

2 CLIPS

DRIVER’S DASHBOARD UNDER COVER

KNOB


30. Remove the driver’s dashboard lower cover (eight clips).

31. Remove the vehicle white 34-pin connector from the fuse box by pushing the retaining tab and raising the lock lever of the connector. Return the lock lever on the vehicle white 34-pin connector and remove the cover by sliding it.

5202121T

8 CLIPS

DRIVER’S DASHBOARD LOWER COVER

851202AK

Push.

VEHICLE WHITE 34-PIN CONNECTOR

WHITE 34-PIN CONNECTOR

Push. Slide.

Push.RETAINING TAB

COVERFUSE BOX

LOCK LEVER

(0808) 7 of 13

32. Insert the white/red and blue terminals from the switch harness into the vehicle white 34-pin connector.

33. Reinstall the vehicle white 34-pin connector.

34. Plug the switch harness 6-pin connector into the fuse box.

5311150T

SWITCH HARNESS TERMINALS

Harness Side View

LOCK LEVERWHITE/RED TERMINAL

BLUE TERMINAL

SWITCH HARNESS

VEHICLE WHITE 34-PIN CONNECTOR

5311160T

VEHICLE 6-PIN CONNECTOR

SWITCH HARNESS

FUSE BOX

SWITCH HARNESS 6-PIN CONNECTOR

8 of 13 AII 40101

NOTE: If the fuse box 6-pin connector is already being used by another accessory, unplug its 6-pin connector from the fuse box. Locate the 6-pin connector taped to the switch harness, and remove the dummy connector. Plug the other accessory’s harness 6-pin connector into the switch harness, and plug the switch harness 6-pin connector into the fuse box.

5311310T

OTHER ACCESSORY HARNESS 6-PIN CONNECTOR

DUMMY CONNECTOR (Discard.)


FUSE BOX



35. Route the terminal from the switch harness down.

36. Unplug the vehicle blue 20-pin connector.37. Slide the retainer from the vehicle blue 20-pin

connector backward, and insert the violet terminal from the switch harness into the vehicle blue 20-pin connector. Reinstall the vehicle blue 20-pin connector.

38. Route the switch harness relay block above the knee bolster.

6510010T

SWITCH HARNESS

Harness Side View

SWITCH HARNESS VIOLET TERMINAL

RETAINER

VEHICLE BLUE 20-PIN CONNECTOR

5311180T

SWITCH HARNESS

KNEE BOLSTER


39. Plug the relay into the switch harness relay block, then slide the relay block onto the vehicle bracket stay.

40. Remove the vehicle ground bolt. Install the switch harness ground terminal, then reinstall the vehicle ground bolt.

860603AK

SWITCH HARNESS

VEHICLE BRACKET STAY

RELAY

SWITCH HARNESS RELAY BLOCK

5311200T

SWITCH HARNESS

SWITCH HARNESS GROUND TERMINAL

VEHICLE GROUND BOLT (Reuse.)

FRONT

(0808) 9 of 13

41. Locate the 1-pin connector blue-taped to the vehicle harness. Plug the switch harness 1-pin connector into the vehicle 1-pin connector.

42. While wearing gloves, push the switch cover out from the inner side of the meter panel.

5311212T

SWITCH HARNESS SWITCH HARNESS

1-PIN CONNECTOR

VEHICLE 1-PIN CONNECTOR

5311330T

METER PANEL

SWITCH COVER (Discard.)

10 of 13 AII 40101

43. Route the switch harness 5-pin connector through the hole.

44. Plug the switch harness 5-pin connector into the switch and install the switch to the meter panel.

45. Secure the switch harness to the vehicle harness and the knee bolster with nine wire ties in the areas shown.

871720AK

SWITCH

METER PANEL


5311242T

KNEE BOLSTER

VEHICLE HARNESS

SWITCH HARNESS 9 WIRE TIES


46. Install the 20 A fuse into the fuse box in the location shown. If the fuse is already installed, it is not necessary to install the fuse from the kit.

47. Check that all wire harnesses are routed properly and all connectors are plugged in.

48. Reinstall all removed parts.49. Connect the negative cable to the battery and check

operation of all lights and other electrical accessories.

50. Enter the anti-theft codes for the audio system, and reset the radio station presets.

51. Reset the clock.

5307240T

FUSE LOCATION “6”

20 A FUSE

FUSE BOX

FUSE BOX


USE AND CAREHow to Operate the Fog Lights

• Turn the light switch to the “ ” position (headlights on low beam).

• Press the fog light switch (indicator is on).

NOTE: The fog light lenses can cloud when the outside temperature is cold; this is normal and should go away in warm weather.

Adjusting the Aim1. Adjust the vertical aim according to local laws and

regulations. Turn the adjusting screw in or out until the correct angle is obtained.

2. Repeat on the right side.

871715AK

FOG

LIG

HT

SWIT

CH

OFF

Low High

-

-

-

-

- -

-

OFF

HEADLIGHT SWITCH

ON ON

851403AK

ADJUSTING SCREW

To raise.To lower.

(0808) 11 of 13

BULB REPLACEMENT1. Remove the two self-tapping screws, and pull the fog

light out toward you.

2. Unplug the connector from the fog light while pushing the retaining tab of connector.

851404AK

2 SELF-TAPPING SCREWS

FOG LIGHT

851405AK

RETAINING TAB(Push.)

CONNECTOR

FOG LIGHT

12 of 13 AII 40101

3. Remove the bulb from the fog light by turning it.

851406AK

FOG LIGHT

BULB


4. Install a new bulb on the fog light by turning it clockwise until it stops.• Take extreme care when replacing the fog light

bulb to avoid damaging the lenses or finished surfaces of the body.

• Use only a Honda Genuine halogen light bulb of specified wattage. Rating: 12V 55W H11 Halogen Light Bulb P/N33165-S5A-003

• Do not touch the bulb. Oily or greasy substances on the bulb can shorten its service life due to the heat produced when the bulb is turned on. If the bulb is accidentally touched, wipe it clean with a soft cloth that has been dampened with a denatured alcohol or a mild detergent solution.

• When installing the new bulb, align the cutout on the fog light with the tab on the new bulb and turn the new bulb in completely. If not properly aligned, the fog light may blind oncoming drivers.

5. Plug the connector into the bulb.6. Reinstall the fog light.7. After the replacement, check that the bulb comes on

properly. Adjust the fog light aiming adjustment as necessary.

851407AK

CONNECTOR

FOG LIGHT

NEW BULB

Turn the bulb until it stops.

(0808) 13 of 13

Documents

INSTALLATION AII 40101 INSTRUCTIONS 2-DOOR · AII 40101 (0808) 08V31-SVA-1F00-91 1 of 13 AII 40101 FOG LIGHTS 2009-2010 CIVIC 2-DOOR (EX-L) AUG 2008 PARTS LIST Right fog light Left