AII 24288 Fog Lights - HondaPartsDeals.com€¦ · AII 24288 (0212) 1 of 13 INSTALLATION INSTRUCTIONS Accessory Application Publications No. Issue Date DEC 2002 FOG LIGHTS 2003 ELEMENT

© 2002 American Honda Motor Co., Inc - All Rights Reserved. AII 24288 (0212) 1 of 13

INSTALLATIONINSTRUCTIONS

Accessory Application Publications No.

Issue Date

DEC 2002

2003 ELEMENTFOG LIGHTS

PARTS LIST

Fog Light Kit (sold separately)P/N 08V31-SCV-100

2 Fog lights

Switch harness

Fog light harness

Relay

Fuse label

20 Wire ties

13 Wire ties with clip

8 Self-tapping screws

Fog Light Switch Kit (sold separately)P/N 08V31-SCV-110A (black)P/N 08V31-SCV-120A (gray)

Switch

TOOL AND SUPPLIES REQUIREDPhillips screwdriverFlat-tip screwdriverRatchet10 mm socketFileDrill3 mm and 20 mm Drill bitsUtility knifeDiagonal cuttersPushpinHacksaw blade

Clip remover

08V31-SCV-1000-91

2422021K

SWITCHHARNESS

SWITCH

RELAY

FOG LIGHT

FOG LIGHTHARNESS

FOGLIGHT

FUSECASE(20A)

INSTALLATION

Customer Information: The information in thisinstallation instruction is intended for use only byskilled technicians who have the proper tools,equipment, and training to correctly and safely addequipment to your vehicle. These procedures shouldnot be attempted by “do-it-yourselfers.”

NOTE: This installation instruction shows the left foglight being installed; the same procedure applies toinstalling the right fog light.

1. Make sure you have the anti-theft code for theradio, then write down the frequencies for thepreset buttons.

2. Disconnect the negative cable from the battery.

AII 24288

Illustration of the Fog Lights Installed on the Vehicle

2 of 13 AII 24288 (0212) © 2002 American Honda Motor Co., Inc - All Rights Reserved.

Installing the Fog Light

3. Open the hood and remove the radiator cover (fiveclips).

5. Inside the front bumper, locate the three marks onthe fog light housing on the left side. Using apushpin, pierce the bumper at the center of eachmark. While wearing eye protection, drill a 3 mmpilot hole then finish with a 20 mm hole throughthe bumper at the center of each mark.

4. Remove the front bumper (seven clips at the top,six clips and four stepped bolts at the bottom andone self-tapping screw on each side).

6. While being careful not to scratch the bumper, usea hacksaw blade to cut out the marked area fromthe front bumper along the inside of the scribedline and the groove on the back. Remove all burrsfrom the edges of the cutout.

2328091K

CLIP

RADIATORCOVER

2328101K

CLIPS (7)

FRONTBUMPER

SELF-TAPPINGSCREWS (2)

STEPPEDBOLTS (4)

CLIPS(6)

2329011K

FRONTBUMPER

PUSHPIN

DRILL BITS(First drillwith a 3 mmbit, andfinish with a20 mm bit).

MARKS (3)

FOG LIGHTHOUSING

2329023K

Cut out.SCRIBED LINE

FRONTBUMPERGROOVE

SECTIONAL VIEW

Cut out.


7. Inside the front bumper, slide the fog light into thecutout you made, and secure it with four self-tapping screws.

10. Locate the 1-pin connector blue-taped to thevehicle harness and remove the blue tape to freethe 1-pin connector. Connect the 1-pin connectoryou just freed to the fog light harness 1-pinconnector .

11. Loosen the ground bolt that fastens the vehicleground terminal and secure the fog light harnessground terminal using this ground bolt.

12. Secure the fog light harness 1-pin connector andthe fog light harness to the vehicle harness withone wire tie. Do not secure the 1-pin connector tothe SRS harness with the wire tie.

2403021K

FOG LIGHTHARNESS

FOG LIGHT HARNESSGROUND TERMINAL

GROUNDBOLT

2402011K

WIRE TIE

FOG LIGHTHARNESS 1-PINCONNECTOR

FOG LIGHTHARNESS

SRSHARNESS

Routing the Fog Light Harness

9. Starting under the left headlight, route the fog lightharness 1-pin connector and ground terminalthrough the hole in the front bulkhead.

8. Repeat steps 5 thru 7 to cut the bumper andinstall the fog light on the right side of the bumper.

2329030K

FOG LIGHT

FRONTBUMPER

SELF-TAPPINGSCREWS (4)

2403010K

BLUETAPE

FOG LIGHTHARNESS1-PINCONNECTOR

FOG LIGHTHARNESSGROUNDTERMINAL

VEHICLE 1-PINCONNECTOR

LEFT FRONTBULKHEADPANEL

FOG LIGHTHARNESS


2417070K

2418010K

2409050K

2403030K

13. Behind the front side frame, route the fog lightharness 2-pin connector (short end) down, and outthrough the clearance between the side frame andfront bumper beam. Attach the wire tie with clip tothe fog light harness at the green tape, then pushthe clip into the hole in the side frame.

14. Route the fog light harness 2-pin connector (longend) up along the bulkhead side stay, then alongthe vehicle harness behind the front bulkheadupper frame.

15. Continue routing the fog light harness 2-pinconnector forward, then down to the bottom of thefront side frame along the outside of the rightbulkhead side stay.

16. Align the green tape on the fog light harness(closest to the connector) with the hole in the frontlower cross member, then secure the harness tothe hole with the wire tie in the area shown.

LEFT FRONTSIDE FRAME

GREENTAPEWIRE TIE

WITH CLIPFOG LIGHTHARNESS 2-PINCONNECTOR(SHORT END)

FRONT BUMPERBEAM

FRONT BULKHEADUPPER FRAME

VEHICLEHARNESS

FOG LIGHTHARNESS

FOG LIGHTHARNESS

RIGHTBULKHEADSIDE STAY

FOG LIGHTHARNESS 2-PINCONNECTOR

FRONT SIDEFRAME

FOG LIGHTHARNESS

FOG LIGHTHARNESS

WIRE TIE

FRONT LOWERCROSS MEMBER

GREENTAPE

FRONT BUMPERBEAM


17. Attach the three wire ties with clips to the fog lightharness at the green tapes, then push the clipsinto the holes in the bulkhead side stay. Furthersecure the fog light harness to the vehicle harnesswith two wire ties in the areas shown.

If the vehicle is equipped with an engine blockheater:

Secure the engine block heater and fog light harnessesto the bulkhead side stay with the wire ties on theengine block heater harness and two wire ties withclips on the fog light harness.

18. Secure the fog light harness to the vehicleharness with six wire ties in the areas shown.

19. Secure the fog light harness to the holes in thebulkhead side stay and the side frame with fourwire ties with clip.

20. Secure the fog light harness to the front bulkheadarea with the wire tie with clip, and to the vehicleharness with one wire tie.

21. Secure the fog light harness to the hole under thefront side frame with one wire tie with clip.

2418050K

FOGLIGHTHARNESS

WIRE TIEWITH CLIP

WIRE TIE

LEFT FRONTSIDE FRAME

WIRE TIEWITH CLIP

LEFTBULKHEADSIDE STAY

LEFT FRONTBULKHEAD

2418041K

WIRE TIE

WIRE TIE

FOG LIGHTHARNESS

WIRE TIEWITH CLIP

2418022K

WIRE TIE

FOG LIGHTHARNESS

WIRE TIEWITH CLIP (3)

GREENTAPE

FOG LIGHTHARNESS


2418031K

FOG LIGHTHARNESS

WIRE TIE WITH CLIPON FOG LIGHT HARNESS

ENGINE BLOCKHEATER HARNESS

WIRE TIE ONENGINE BLOCKHEATER



22. While holding the front bumper near the front ofthe vehicle, plug the fog light harness 2-pinconnectors into the 2-pin connectors from the foglights. Reinstall the front bumper.

24. Remove the center dashboard lower cover (twoexpansion clips, two clips and four retaining tabs).

NOTE: This illustration shows the center lower coverwith subwoofer. Remove the center lower cover withoutsubwoofer the same way.

Routing the Switch Harness

23. Remove the driver’s dashboard lower cover, turnthe knobs clockwise, then pull the cover outtoward you to release the six retaining tabs.

2418061K

FOG LIGHT2-PINCONNECTOR


FOG LIGHTFRONT BUMPER

FOG LIGHT


2403050K

RETAININGTABS (6)

KNOB

DRIVER’SDASHBOARDLOWERCOVER

2403062K

RETAININGTABS (4)

EXPANSIONCLIPS (2)

CENTERDASHBOARDLOWER COVER

CLIPS (2)


25. Starting from behind the instrument panel, routethe switch harness 8-pin connectors down alongthe vehicle harness. On the left of the instrumentpanel frame, unplug the vehicle 8-pin connectors(gray), and plug the switch harness 8-pinconnectors in between the switch harnessconnectors and the vehicle connector.

26. Slide the switch harness 8-pin connector onto theholder on the vehicle 8-pin connector (gray).

27. Locate the 1-pin connector blue-taped to thevehicle harness and remove the blue tape to freethe connector. Plug the vehicle harness 1-pinconnector into the switch harness 1-pin connector(blue/red).

28. At the fuse box, plug the switch harness1-pin connector (white/red) into the fuse box in thelocation shown.

2404011K

SWITCHHARNESS

SWITCHHARNESS 8-PINCONNECTOR

VEHICLE 8-PINCONNECTOR(GRAY)

HOLDER

2403072K

VEHICLE 8-PINCONNECTOR(GRAY)

INSTRUMENTPANEL FRAME

VEHICLECONNECTOR(Cruisecontrolsystemequippedonly.)

INSTRUMENTPANEL

SWITCHHARNESS

2404022K

SWITCH HARNESS1-PIN CONNECTOR(BLUE/RED)

VEHICLEHARNESS BLUE TAPE


SWITCHHARNESS

2405010K

FUSE BOX

SWITCHHARNESS 1-PINCONNECTOR(WHITE/RED)

SWITCHHARNESS

1-PIN CONNECTORCONNECTING PORT

SWITCHHARNESS 8-PINCONNECTOR


30. On M/T only: Plug the switch harness 6-pinconnector into the fuse box.

29. On A/T only: Unplug the vehicle 6-pin connectorfrom the fuse box. Remove and discard thedummy connector from the 6-pin connector black-taped to the switch harness. Plug the switchharness 6-pin connectors in between the fuse boxand the vehicle connector.

31. Unplug the vehicle 12-pin connector from the fusebox and plug the switch harness 12-pinconnectors in between the fuse box and thevehicle connector.

32. Attach the fuse label (20A) to the fuse case on theswitch harness.

33. From under the steering shaft, route the switchharness 5-pin connector to the left from behind theknee bolster.

34. Remove the switch cover from the instrumentpanel, and pull the switch harness 5-pin connectorout through the hole.

2405021K

SWITCH HARNESS6-PIN CONNECTOR

VEHICLE 6-PINCONNECTOR(A/T only)

SWITCH HARNESS6-PINCONNECTOR

FUSE BOX 6-PINCONNECTOR PORT

DUMMYCONNECTOR(Discard.)

FUSEBOX

SWITCHHARNESS

2405031K

FUSEBOX

SWITCH HARNESS6-PINCONNECTOR

SWITCHHARNESS

2405051K

SWITCHHARNESS5-PINCONNECTOR

SWITCHCOVER(Discard.)

SWITCHHARNESS

STEERINGSHAFT

KNEEBOLSTER

FUSECASE ONSWITCHHARNESS

FUSELABEL(20A)

2405041K

SWITCHHARNESS12-PINCONNECTOR


SWITCHHARNESS

FUSE BOX 12-PINCONNECTOR PORT

FUSEBOX


36. Align the green tape on the switch harness withthe vehicle harness clip, then secure the switchharness to the vehicle harness with the three wireties in the areas shown.

NOTE: If the vehicle is not equipped with a cruisecontrol switch, attach the wire tie with clip to theswitch harness. Push the switch harness clip fromthe wire tie with clip into the hole in the instrumentbracket.

35. Plug the relay into the switch harness relay block,then slide the relay block onto the instrumentpanel bracket stay.

37. Attach a wire tie with clip to the switch harness atthe green tape, then push the clip into the hole inthe steering hanger lower bracket.

38. Secure the switch harness to the vehicle harnessand to the hole in the steering hanger lowerbracket with two wire ties and one wire tie withclip. Move the steering wheel up and down toconfirm that the switch harness is not beingpulled. Readjust if necessary.

2409011K

WIRE TIEWITH CLIP

SWITCHHARNESS

VEHICLECLIP

GREENTAPE

WIRETIE

WIRETIE

SWITCHHARNESS

INSTRUMENTPANELBRACKET

WIRE TIE

With cruisecontrol switch

Without cruisecontrol switch

2408011K

SWITCHHARNESS

SWITCHHARNESSRELAYBLOCK

RELAY

INSTRUMENT PANELBRACKET STAY

2409022K

SWITCHHARNESS

WIRE TIEWITH CLIP

WIRETIE

STEERINGHANGERLOWERBRACKET

GREENTAPE

WIRETIEWITHCLIP

WIRETIE

SWITCHHARNESS


40. Plug the switch harness 5-pin connector (blue) intothe switch, then install the switch in the hole in theinstrument panel.

41. Check that all wire harnesses are routed properlyand all connectors are plugged in.

42. Reinstall all removed parts. Check that all clipsand fasteners are installed securely.

43. Reconnect the negative cable to the battery.

44. Reset the clock, and reset the radio stationpresets.

NOTE: Whenever the battery is disconnected, thedriver’s window AUTO function is disabled.

45. Start the engine. Push down on the driver’swindow switch until the window is fully open.

46. Pull up on the driver’s window switch to close thewindow completely, then hold the switch for2 seconds.

47. Lower and raise the window to check the operationof the driver’s window AUTO function.

USE AND CARE

How to Operate Fog Lights

• Turn the light switch to the “ ” position(headlights on low beam).

• Press the fog light switch (indicator is on).

The fog light lenses can cloud when the outsidetemperature is cold; this is a normal condition.

39. Secure the switch harness to the vehicle harnesswith two wire ties in the areas shown.

2409031K

WIRETIE

SWITCHHARNESS

2409040K

INSTRUMENTPANEL

SWITCH

SWITCHHARNESS 5-PINCONNECTOR(BLUE)


Replacing the Fog Light Bulb

1. Loosen the upper right screw on the fog light. Liftthe fog light up, then pull it out toward you.

2. Remove the fog light connectors from the bracketstay, then unplug the connectors. Remove the foglight.

3. Remove the fog light rear cover (five screws).

Fog Light Aiming Adjustment

• Adjust the aiming according to local laws andregulations.

• To adjust, turn the aiming adjustment screw in orout until the correct aiming is obtained.

2419010K

BRACKETSTAY

CONNECTORFOG LIGHT

2419030K

SCREWS (5)

REARCOVER

FOG LIGHT

2418070K

To raise

To lower

PHILLIPSSCREWDRIVER

AIMING ADJUSTMENTSCREW

2419020K

FOG LIGHTAIMINGADJUSTMENTSCREW UPPER RIGHT

SCREW (Loosen.)

FOG LIGHT

HOOK


5. Install the new bulb into the socket.

• Use only a genuine Honda halogen light bulb ofspecified wattage.

Rating: 12V 55W H3 Halogen Light BulbP/N 33165-SB0-7310-M1

• Do not touch the bulb. Oily or greasysubstances on the bulb can shorten its servicelife due to the heat produced when the bulb isturned on. If the bulb is accidentally touched,wipe it clean with a soft cloth that has beendampened with denatured alcohol or a milddetergent solution.

• Align the tab on the fog light with the cutoutwhen installing the new bulb. If it is not aligned,the fog light may annoy oncoming drivers.

6. Reinstall the removed parts in the reverse order ofremoval.

• Check that the wire harnesses are not pinched.

• Make sure to tighten the screws securely.

4. Remove the retainer spring, and pull out the bulband socket as a unit.

BULB

RETAINERSPRING

HOOK

CUTOUT

NEW BULB

TAB


OFF

LIGHT SWITCH

OFFLow Hi

OFF

ON ON

FO

G L

IGH

TS

WIT

CH

BLK

YEL

BLU

GRN

RED

WHT

BLACK

YELLOW

BLUE

GREEN

RED

WHITE

BROWN

ORANGE

LIGHT BLUE

LIGHT GREEN

PINK

GRAY

BRN

ORN

LT BLU

LT GRN

PNK

GRY

HOT ATALL TIMES

HOT WITHHEADLIGHTSWITCH INHEAD HOT WITH

HEADLIGHT SWITCHIN PARK OR HEAD

FRONT FOGLIGHT

20A

RED/YELFog LightFuse WHT

RED/BLK

RED/BLURED

IlluminationControl

RED/WHT

Fog LightRelay

BLU/RED

FrontFogLights

BLK

1 2DimmerSwitch1: Low2: High

1 2

Switch1 = Switch

Illumination2 = Indicator

WHT/RED

CIRCUIT DIAGRAM

Documents

AII 24288 Fog Lights - HondaPartsDeals.com€¦ · AII 24288 (0212) 1 of 13 INSTALLATION INSTRUCTIONS Accessory Application Publications No. Issue Date DEC 2002 FOG LIGHTS 2003 ELEMENT