ABB rastavljacke pruge

ProtectIT Fuse switch disconnector, XLBM 160-630A

InLine-Engelsk-high_OR 06.05.03 09:33 Side 1


Contents

Fuse protection

General

Apparatus and accessories 3.1 Standard apparatus3.2 IP20 Z-busbar system and apparatus3.3 Accessories

Technical data

Ordering tables

Dimensional drawings

1

2

3

4

5

6



InLine1. Fuse protection

51SEC312022B0101

1Fuse protection – Easy and reliableThe fuse is a superior short circuit protection element regardingthe maximum allowed cut-off current (peak let through current)and energy value. This is more important the higher the voltageand prospective fault levels are. The SlimLine switch fuses fulfilthe highest requirements for modern switch fuses with a totalsafety concept. The switch fuses are tested according to theEN 60947-3 standard with more stringent requirements for iso-lation, making, performance and safety.

The melting curves and current limiting diagrams for NH fuselinks are given in the IEC 269-2 standard. The standardisedfuse characteristics and high degree of current limitation ensurethat there is a simple and effective coordination with fuse linksand other devices.

Fuse links provide a simple procedure for selecting the rightfuse type for your installation, without complicated calculationsor calculation tools. Fuses prevent "blackouts". Only the fusenearest a fault trips without upstreams fuses (feeders or mins)being affected. Fuses thus provide selective coordination.When more power is needed in an installation, more feederscan be added without changing the present structure or anynew selectivity calculations. Fuse links will assure selectivity inthe installation by 1,6:1 difference in the rated current.

Economical installationLifetime costs of fuse systems are low. Fuse links which canwithstand a high fault level and a fault current, are available ateconomical prices. After fuse operation, only the fuse link hasto be changed. Because the fuse links can be rapidly and easi-ly replaced, plant down time and maintenance are substantiallyreduced with a fuse link system.

Because the fusing elements operate in a cylinder, they are notaffected by their surroundings. Thus their protecting characte-ristics remain stable year after year. The dynamic stress on thenetwork and its equipment is dependent of the let through ener-gy (i2t) at a short circuit. The fuse link provides the best protec-tion compared to other solutions, at high short circuit currents.As the fuse link body is filled with quartz sand, there will be noemission of gases or arcs when a short circuit occurs. Thisagain leads to less stress on the network and a higher degreeof personal safety.

Fuse protection – Easy and reliable• Economical installation• Easy and economical selectivity • No need for calculation tools • No need to change the present structure when more power is needed

• No moving parts• No extra operation time• No arc space• No emission of gasses at short circuits

No need for calculation tools - Easy and economical selectivity

No moving parts – No extra operation time


InLine2. General

61SEC312022B0201

Family presentation

InLine is the new generation of vertical fuse rails and fuseswitch disconnectors from ABB. ABB has a long history in producing these types of devices,and the first generation was introduced already in 1967. TheInLine family consists of fuse rails, single-, and triple pole ope-rated fuse switch disconnectors and incoming/outgoing units.

Areas of applications

• Cable distribution cabinets (CDC)• Low voltage distribution in secondary transformer

substations• Distribution boards for industry, housing and office buildings

Inplan

InPlan is a software tool for planning and designing InLineapplications. It may be used to have:- Front view diagram- Single line diagram- Material listThese can all be printed and used for documentation and offerswhere InLine is used.

Applications

• Cable distribution cabinets• Low voltage distribution in transformer secondary

substations• Switchboards for industries• Installations

2

– The new solution for your distribution


71SEC312022B0201

InLine2. General

Properties

• Fully type tested in accordance with IEC 60947-3

• Compact 48 and 98 mm width

• 185mm busbar distance

• For flat or IP20 z-profile busbar

• Wide range of accessories

• Possibility of top, bottom or side cable connection

• IP20 from the front

• Available with Electronic Fuse Monitoring (EFM)

• Current metering on both the cable and busbar side

• Safe live installation with IP20 system

• V0 – flame retardant materials

Advantages

• Complete range for all applications

• Modern and sturdy design

• Flexibility – snap on solutions

Industrial IT describes the ABB group commitment to bridging the gapbetween industrial and business assets and the information tech-nology (IT) required to integrate these components in real time. Thecommitment encompasses a portfolio of compatible technologies forpower, automation, and information; a robust, open architecture forintegrated solutions; plus the domain expertise acquired throughmore than 100 years of meeting customer needs.

This product has been certified by ABB Group as Industrial IT nabled™ - Information Level.

All product information is supplied in interactive electronic format,based on ABB Aspect Object™ technology. The Industrial IT commitment from ABB ensures that every enterprisebuilding block is equipped with the integral tools necessary to install,operate, and maintain it efficiently throughout the product lifecycle.

2


81SEC312022B0201

InLine3. Apparatus and accessories

3.1 Standard apparatus

XUBM fuse rail

XUBM00-100 XUBM00 XUBM1/2/3

Fuse link NH00 NH00 NH1/2/3

Rated current 160 A 160 A 250 A400 A630 A

Module width 50 mm 50 mm 100 mm

Cable Al / Cu mm2 1) 1,5 - 95 1,5 - 95 95 - 240

Cable terminal 2) 3 x M8 3 x M8 3 x M12

Order code 1SEP101836R0001 1SEP10211R0101 XUBM1 – 1SEP102111R0101XUBM2 – 1SEP102112R0101XUBM3 – 1SEP102113R0101

3

1. Cable lugs in accordance with DIN 46235 and DIN 46239.

2. Cable clamps are available as accessories.




91SEC312022B0201

XLBM fuse switch disconnector

XLBM00-3P-100 XLBM00-1P XLBM00-3P XLBM1/2/3-1P XLM1/2/3-3P

Fuse link NH00 NH00 NH00 NH1/2/3 NH1/2/3

Rated current 160 A 160 A 160 A 250 A 250 A400 A 400 A630 A 630 A

Module width 50 mm 50 mm 50 mm 100 mm 100 mm

Cable Al / Cu mm2 1) 1,5 - 95 1,5 - 95 1,5 - 95 95 - 240 95 - 240

Cable terminal 2) 3 x M8 3 x M8 3 x M8 3 x M12 3 x M12

Order code 1SEP101818R0001 1SEP102140R0101 1SEP102140R0101 XLBM1 – 1SEP102141R0101 XLBM1 – 1SEP102141R0121

XLBM2 – 1SEP102142R0101 XLBM2 – 1SEP102142R0121

XLBM3 – 1SEP102143R0101 XLBM3 – 1SEP102143R0121

3

1. Cable lugs in accordance with DIN 46235 and DIN 46239.

2. Cable clamps are available as accessories.




101SEC312022B0201

Guide marks

In the back of the fuse rail it is printed «guide marks». This makes it easier to mark drilling holes in the busbars.

Hooked clamp

It is possible to install the fuse rail with hooked clamp onlive busbar. This feature is further described in the IP20Z-busbar system chapter.The hooked clamp do not require bolts in the busbars.This enables an easy and quick installation. The hookedclamp covers all busbar widths up to 10 mm.

Top/bottom cable termination

Fixing the fuse switch housing

1SEB00010725Nm

M12

90° 3

2

1




111SEC312022B0201

3

Sealing

Padlock – closed position

Padlock – open position

Interlocked by useof cable shroud

Voltage measurement

Common features XLBM


BZ 630 A

BZ 630A/284 630 A 284 mm 1SEP824067R0001

BZ 630A/536 630 A 536 mm 1SEP824068R0001

BZ 630A/851 630 A 851 mm 1SEP824069R0001

BZ 630A/1201 630 A 1201 mm 1SEP824070R0001


3.2 IP20 Z-busbar system and apparatus

121SEC312022B0201

BZ 400 A

BZ 400A/284 400 A 284 mm 1SEP824063R0001

BZ 400A/536 400 A 536 mm 1SEP824064R0001

BZ 400A/851 400 A 851 mm 1SEP824065R0001

BZ 400A/1201 400 A 1201 mm 1SEP824066R0001

Type Rated current Width Order code

XUBM-Z and XLBM-Z may be hooked on:• Z busbars type BZ• Standard flat Cu-bars

3

IP20 Z-busbars, type BZ

Z-busbars for 400/630 A. The busbar kit includes:• Busbar L1, L2 and L3 • Two busbar holdersThe Z-busbars are completely IP20 protected.




131SEC312022B0201

XUBM-Z fuse rails

XUBM00-Z XUBM1/2/3-Z XUBM1/2/3-ZS

Fuse link NH00 NH1/2/3 NH1/2/3

Rated current 160 A 250 A 250 A400 A 400 A630 A 630 A

Module width 50 mm 100 mm 150 mm

Cable Al / Cu mm2 1,5 - 95 95 - 240 50 - 300

Cable terminal 3 x M8 3 x M12 Clamps

Order code 1SEP102110R0201 1SEP102111R0201 1SEP102111R04051SEP102111R0121 1SEP102112R04051SEP102112R0121 1SEP102111R0405

3




141SEC312022B0201

XLBM00-1P-Z XLBM1/2/3–1P–Z XLBM1/2/3-1P-ZS XLBM1/2/3-1P-Z2S

Fuse link NH00 NH1/2/3 NH1/2/3 NH1/2/3

Rated current 160 A 250 A 250 A 250 A400 A 400 A 400 A630 A 630 A 630 A

Module width 50 mm 100 mm 150 mm 208

Cable Al / Cu mm2 1,5 - 95 95 - 240 50 - 300 2 x 50 - 300

Cable terminal 3 x M8 3 x M12 Clamps Clamps

Order code 1SEP102140R0201 1SEP102141R0201 1SEP102141R0401 1SEP102141R05011SEP102141R0201 1SEP102142R0401 1SEP102142R05011SEP102142R0201 1SEP102143R0401 1SEP102143R0501

3

XLBM 1 pole-Z fuse switch disconnector




151SEC312022B0201

XLBM 3 pole-Z fuse switch disconnector

XLBM00-3P-Z XLBM1/2/3-3P-Z XLBM1/2/3-3P-ZS XLBM1/2/3-3P-Z2S

Fuse link NH00 NH1/2/3 NH1/2/3 NH1/2/3

Rated current 160 A 250 A 250 A 250 A400 A 400 A 400 A630 A 630 A 630 A

Module width 50 mm 100 mm 150 mm 208 mm

Cable Al / Cu mm2 1,5 - 95 95 - 240 50 - 300 2 x 50 - 300

Cable terminal 3 x M8 3 x M12 Clamps Clamps

Order code 1SEP102140R0221 1SEP102141R0221 1SEP102141R0421 1SEP102141R05211SEP102142R0221 1SEP102142R0421 1SEP102142R05211SEP102142R0221 1SEP102143R0421 1SEP102143R0521

3




161SEC312022B0201

Feeding clamp for IP20 Z-busbar

Modules with hooked clamp (Z)

AKZD 95 AKKZ 300 LDL 63/3Rated current 160 A 630 A 63 AModule width 35 mm 55 mm 105 mmCable Al / Cu mm2 6 - 95 / 2 x 6 - 50 50 - 300 6 - 25Order code 1SEP731594R0001 1SEP731521R0001 1SEP731530R0001

3 Diazed fuse rail




171SEC312022B0201

Load break switch, switch fuse and sectionalising load break switch

LB 160 160A load break switch 160 1,5 - 95 168 1SEP731800R0001

LB 250 250A load break switch 250 1,5 - 95 168 1SEP731802R0001

LB 400 400A load break switch 400 50 - 300 217 1SEP731804R0001

LB 630 630A load break switch 630 50 - 300 245 1SEP731806R0001

FLS 160 160A switch fuse 160 1,5 - 95 168 1SEP731808R0001

FLS 250 250A switch fuse 250 50 - 300 217 1SEP731810R0001



LS 160 160A load break switch-sectionallizer 160 168 1SEP731816R0001




FSS 160 160A switch fuse - sectionallizer 160 168 1SEP731824R0001




Type Item description Rated current Cu/Al Module Order codeA mm2 width

3




181SEC312022B0201

Fuse Monitoring

Electronic Fuse Monitoring (EFM)

The fuse monitor is a fuse blown monitoring and indication device. The voltage supply to the internal electronic device is supported directlyby connection to the internal fuse holders.In case of a blown fuse, the internal relay will trip for giving possibleremote alarm. Aditionally the green LED lamp in the front will change to red.After replacement to a new fuse link, the relay will automatically be reset.

NOTE: The fuse monitor requires supply from the busbar side.

Technical data :

Minimum operation voltage: 380Maximum operation voltage: 690VUimp over a blown fuse : 12,3 kVUimp between phases : 9.8 kVUimp between main circuit/ relay contacts. : 9.8 kVDielectric test voltage input / output : 3.5 kV / 50 Hz / 1 minuteElectrostatic Discharge : EN61000-4-2 +/- 4 kV.Electrical Fast Transient: EN61000-4-4 +/- 2 kVConducted Fast transient: EN61000-4-6

10Vrms / 150kHz – 80 MHzWire size : 15 mm2

EMC tested: Yes

Relay:Nominal current: 8 ampNominal switching capacity: 2000VA, AC1Maximum switching voltage: 440V AC, 250V DC

3

LED Fuse Monitoring (LFM)

For simple visible front monitoring of the fuse status, a special LED fusemonitor kit is available. In case of a blown fuse an LED will be ignited inthe front cover at the actual phase. Available as accessory.

1SEB000110



3.3 Accessories

191SEC312022B0201

Accessories XUBM

Phase barrier kit

– for segregation of each phase

– possibility for outlet description

Cable shroud

3

Fuse protection cover

– IP20 protection duringservice work

– require phase barrier kit



3.3 Accessories

201SEC312022B0201

Accessories XLBM - Current meetering

3

Terminal installation

– kit including extension barand CT for 1 phase

– available for size 1/2/3

Ammeter house

– available for size 00 (48x48)and size 1/2/3 (72x72)

– extendable

Front installation– compact fuse for CT and

plug-in ammeter – available for size 1/2

Selector switch

Rear side installation– kit including extension bar

and CT for 3 phases



3.3 Accessories

211SEC312022B0201

Accessories XLBM

Lable holder

3Micro switch– one or two per phase

Auxiliary switch

Huckepack– for temporary additional

output

Cable shroud



3.3 Accessories

Conductor cross section min-max

Type of Conductor Rm/Sm Re/Se Torque Order codeclamp/bolt flexible mm2 mm2 (Nm)

mm2

XLBM / XUBM00

Bridge Clamp (BC) 1,5 – 50 1,5 – 50 1,5 – 50 3,5 1SEP407733R0001

Single Prism Clamp (SPC) 1,5 – 95 1,5 – 95 1,5 – 95 3,5 1SEP407732R0005

XLBM / XUBM1/2/3

V-clamp kit 95 – 240 95 – 240 95 – 240 25 1SEP304446R0001

Double V-clamp kit 2 x 95 – 240 2 x 50 – 185 2 x 70 – 240 25 1SEP304457R00012 x 95 – 240 2 x 120 – 300

Double cable lug kit 2 x 95 – 240 2 x 70 – 240 2 x 70 – 240 25 1SEP304502R0001

221SEC312022B0201

Cable termination

3


InLine4. Technical data

231SEC312022B0201

XUBM Fuse rails

XUBM00 XUBM1 XUBM2 XUBM3

For HRC fuse links acc. to IEC 60269-2-1. 00 1 2 3

Rated operational voltage Ue (V) 690 690 690 690

Rated operational current Ie (A) 160 250 400 630

Rated insulation voltage Ui (V) 1000 1000 1000 1000

Conditional short circuit current – with fuse links. (kArms) 50 50 50 50

Rated frequency. (Hz) 50-60 50-60 50-60 50-60

Degree of protection from the front acc. to IEC 60529. *) IP 20 IP 20 IP 20 IP 20

*) With fuse protection cover or isolated gripping lugs

XLBM Fuse switch disconnector

XLBM00 XLBM1 XLBM2 XLBM3

For HRC fuse links acc. to IEC 60269-2-1. 00 1 2 3

Rated operational voltage Ue (V) 400 500 690 400 500 690 400 500 690 400 500 690

Rated operational current Ie (A) 160 160 125 200 250 200 315 400 315 500 630 500

Thermal current w/fuse link lth (A) 160 250 400 630

Rated insulation voltage Ui (V) 1000 1000 1000 1000

Rated impulse withstand voltage Uimp (kV) 8 8 8 8

Fuse protected short circuit withstand (kArms) 50 50 50 50

Fuse protected short circuit making (kArms) 50 50 50 50

Rated making and breaking AC23B AC22B AC21B AC23B AC22B AC21B AC23B AC22B AC21B AC23B AC22B AC21B

capacity:

Rated frequency. (Hz) 50-60 50-60 50-60 50-60

Power losses at Ith without fuse-link (W) 16,1 16,9 36,8 75,4

Degree of protection from Open IP 20 IP 20 IP 20 IP 20the front acc. to IEC 60529. Closed IP 30 IP 30 IP 30 IP 30

4


InLine5. Ordering tables

Order number Type Item description Weight designation Per unit (kg)

XUBM / XLBM

Fuse rail - XUBM

1SEP102110R0101 XUBM00 160A incl. 3M8 1,5

1SEP101836R0001 XUBM00-100 160A 100mm busbardist. incl. 3M8 1,0

1SEP102100R0101 XUBM00-R 160A wo. contact shrouds, incl. 3M8 1,3

1SEP102111R0101 XUBM1 250A incl. 3M12 2,9


1 1SEP102112R0101 XUBM2 400A incl. 3M12 3,4


1SEP102113R0101 XUBM3 630A incl. 3M12 3,9


Fuse switch disconnector - XLBM 1pole

1SEP102140R0101 XLBM00-1P 160A 1 pole, incl. 3M8 2,2

1SEP102140R0111 XLBM00-1P-EFM 160A 1pole, incl. EFM, incl. 3M8 2,3



2 1SEP102142R0101 XLBM2-1P 400A 1 pole, incl. 3M12 4,7




Fuse switch disconnector - XLBM 3pole

1SEP102140R0121 XLBM00-3P 160A 3pole, incl. 3M8 2,3

1SEP101818R0001 XLBM00-3P-100 160A 3pole, 100mm busbardist. incl. 3M8 1,6




3 1SEP102142R0121 XLBM2-3P 400A 3pole, incl. 3M12 4,8




241SEC312022B0201

Explanation:

XUBM = Fuse rail

XLBM = Fuse switch disconnector

XLBM-2 = Apparatus size

XUBM-2-R = Fuse rail without contact shrouds

XLBM-2-1P = Number of operating poles

XLBM-2-1P-EFM = Electronic fuse monitoring

XLBM-2-Z = Hooked clamp

XLBM-2-ZS = Hooked clamp and side connection

XLBM-2-Z2S = Hooked clamp and double side connection

5

1

2

3



251SEC312022B0201


XUBM / XLBM with hooked clamps for IP20 Z- busbar systems Fuse rail - XUBM with hooked clamp (Z)

1SEP102110R0201 XUBM00-Z 160A w. hooked clamp, incl. 3M8 1,71SEP102111R0201 XUBM1-Z 250A w. hooked clamp, incl. 3M12 3,21SEP102111R0405 XUBM1-ZS 250A w. hooked clamp, side connection, incl. 3 clamps 3,2

1 1SEP102112R0201 XUBM2-Z 400A w. hooked clamp, incl. 3M12 3,81SEP102112R0405 XUBM2-ZS 400A w. hooked clamp, side connection, incl. 3 clamps 3,71SEP102113R0201 XUBM3-Z 630A w. hooked clamp, incl. 3M12 4,21SEP102113R0405 XUBM3-ZS 630A w. hooked clamp, side connection, incl. 3M12 4,1

Fuse switch disconnector - XLBM 1pole with hooked clamp (Z)1SEP102140R0201 XLBM00-1P-Z 160A 1pole, w. hooked clamp, incl. 3M8 2,41SEP102140R0211 XLBM00-1P-EFM-Z 160A 1 pole, incl. EFM, w. hooked clamp, incl. 3M8 2,51SEP102141R0201 XLBM1-1P-Z 250A 1pole, w. hooked clamp, incl. 3M12 4,51SEP102141R0211 XLBM1-1P-EFM-Z 250A 1pole, incl. EFM, w. hooked clamp, incl. 3M12 4,71SEP102141R0401 XLBM1-1P-ZS 250A 1pole, w. hooked clamp, side connection, incl. 3 clamps 4,51SEP102141R0501 XLBM1-1P-Z2S 250A 1pole, w. hooked clamp,

double side connection, incl. 6 clamps 5,81SEP102142R0201 XLBM2-1P-Z 400A 1pole, w. hooked clamp, incl. 3M12 5,11SEP102142R0211 XLBM2-1P-EFM-Z 400A 1pole, incl. EFM, w. hooked clamp, incl. 3M12 4,91SEP102142R0401 XLBM2-1P-ZS 400A 1pole, w. hooked clamp, side connection, incl. 3 clamps 5,01SEP102142R0501 XLBM2-1P-Z2S 400A 1pole, w. hooked clamp,


double side connection, incl. 6 clamps 6,7

Fuse switch disconnector - XLBM 3pole with hooked clamp (Z)1SEP102140R0221 XLBM00-3P-Z 160A 3pole, w. hooked clamp, incl. 3M8 2,51SEP102140R0231 XLBM00-3P-EFM-Z 160A 3pole, incl. EFM, w. hooked clamp, incl. 3M8 2,61SEP102141R0221 XLBM1-3P-Z 250A 3pole, w. hooked clamp, incl. 3M12 4,61SEP102141R0231 XLBM1-3P-EFM-Z 250A 3pole, incl. EFM, w. hooked clamp, incl. 3M12 4,81SEP102141R0421 XLBM1-3P-ZS 250A 3pole, w. hooked clamp, side connection, incl. 3 clamps 4,61SEP102141R0521 XLBM1-3P-Z2S 250A 3pole, w. hooked clamp,

double side connection, incl. 6 clamps 5,81SEP102142R0221 XLBM2-3P-Z 400A 3pole, w. hooked clamp, incl. 3M12 5,21SEP102142R0231 XLBM2-3P-EFM-Z 400A 3pole, incl. EFM, w. hooked clamp, incl. 3M12 5,4

2 1SEP102142R0421 XLBM2-3P-ZS 400A 3pole, w. hooked clamp, side connection, incl. 3 clamps 5,11SEP102142R0521 XLBM2-3P-Z2S 400A 3pole, w. hooked clamp,


double side connection, incl. 6 clamps 6,7

Modules with hooked clamp (Z)1SEP731800R0001 LB 160 160A load break switch1SEP731802R0001 LB250 250A load break switch1SEP731804R0001 LB 400 400A load break switch1SEP731806R0001 LB 630 630A load break switch

3 1SEP731808R0001 FLS 160 160A switch fuse1SEP731810R0001 FLS 250 250A switch fuse1SEP731812R0001 FLS 400 400A switch fuse1SEP731814R0001 FLS 630 630A switch fuse1SEP731816R0001 LS 160 160A load break switch-sectionallizer1SEP731818R0001 LS 250 250A load break switch-sectionallizer1SEP731820R0001 LS 400 400A load break switch-sectionallizer1SEP731822R0001 LS 630 630A load break switch-sectionallizer1SEP731824R0001 FSS 160 160A switch fuse -sectionallizer1SEP731826R0001 FSS 250 250A switch fuse -sectionallizer1SEP731828R0001 FSS 400 400A switch fuse -sectionallizer1SEP731830R0001 FSS 630 630A switch fuse -sectionallizer1SEP731530R0001 LDL 63/3 63A diazed unit w. 3 groups1SEP731594R0001 AKZD 95 Direct incomer 0,11SEP731521R0001 AKKZ 300 Direct incomer 0,4

Kit of IP20 Z-busbars1SEP824063R0001 BZ 400A/284 400A/284mm, incl. IP20 busbars&holders1SEP824064R0001 BZ 400A/536 400A/536mm, incl. IP20 busbars&holders1SEP824065R0001 BZ 400A/851 400A/851mm, incl. IP20 busbars&holders

4 1SEP824066R0001 BZ 400A/1201 400A/1201mm, incl. IP20 busbars&holders1SEP824067R0001 BZ 630A/284 630A/284mm, incl. IP20 busbars&holders1SEP824068R0001 BZ 630A/536 630A/536mm, incl. IP20 busbars&holders1SEP824069R0001 BZ 630A/851 630A/851mm, incl. IP20 busbars&holders1SEP824070R0001 BZ 630A/1201 630A/1201mm, incl. IP20 busbars&holders

5

1

2

3

4



261SEC312022B0201


Accessories XUBM /XLBMAccessories for XLBM/XUBM 00

1SEP304069R0001 00 Blind cover adjustable 0,21SEP201543R0001 00 Fuse cover 0,31SEP408124R0001 XUBM00 Cable shroud 0,2

1 1SEP408126R0001 XLBM00 Cable shroud Lenght 185mm 0,21SEP408128R0001 XLBM00 Cable shroud short Lenght 64mm 0,1

2 1SEP408139R0001 00 Label holder 0,11SEP304442R0001 XUBM00 Phase barrier kit Kit incl. 2 pcs. 0,11SEP407733R0001 00 Bridge clamp (3BC) Kit incl. 3 pcs. 1,5-50 mm2 0,11SEP407732R0005 00 Single prism clamp (3PC) Kit incl. 3 pcs. 1,5-95 mm2 0,11SEP304072R0001 00 Adapter for 185mm busbar Single 0,4

3 1SEP304071R0001 00 Adapter for 185mm busbar Double 0,71SEP408141R0001 00 A-meter house QB48 For A-meter 48x48mm 0,1NHSN714003P1150 Max A-meter QB48, 0-150-180/5A 0,11SEP408149R0001 CT busbar kit 160/5A Kit incl. 3 pcs. 2,5VA cl.1 1,1

Accessories for XLBM/XUBM 1, 2, 31SEP304080R0001 1,2,3 Blind cover 0,31SEP201499R0001 1,2,3 Fuse cover 0,41SEP408125R0001 XUBM1,2,3 Cable shroud 0,31SEP408127R0001 XLBM1,2,3 Cable shroud 0,21SEP304395R0001 XUBM1,2,3 Phase barrier kit Kit incl. 2 pcs. 0,21SEP408140R0001 1,2,3 Label holder 0,11SEP407946R0001 XLBM1,2,3 Operated fuse indicator (LFM) Kit incl. 3 pcs. 0,1NHSN722068P0002 1,2,3 Huckepack Temporary supply outlet 0,31SEP304446R0001 1,2,3 V-clamp kit Kit incl. 3 pcs. 0,51SEP304457R0001 1,2,3 Double V-clamp kit Kit incl. 3 pcs. 0,51SEP304502R0001 1,2,3 Double cable lug kit 0,5

4 1SEP408142R0001 1,2,3 A-meter house, IQB72 For A-meter 72x72mm 0,1NHSN714004P2206 Max A-meter QB72, 0-150-180/5A 0,2NHSN714004P2210 Max A-meter QB72, 0-400-480/5A 0,2NHSN714004P2212 Max A-meter QB72, 0-600-720/5A 0,21SEP408149R0002 CT busbar mounted kit 250A/5A Kit incl. 3 pcs. 3,75VA cl.1 1,31SEP408149R0003 CT busbar mounted kit 400A/5A Kit incl. 3 pcs. 5VA cl.1 1,31SEP408149R0004 CT busbar mounted kit 600A/5A Kit incl. 3 pcs. 5VA cl.1 1,31SEP408149R0005 CT busbar mounted kit 600A/5A Kit incl. 3 pcs. 5VA cl.0,5 1,31SEP408149R0006 CT terminal mounted kit 160/5A Kit incl. 1 pc. 2,5VA cl.1 0,61SEP408149R0007 CT terminal mounted kit 250/5A Kit incl. 1 pc. 3,75VA cl.1 0,61SEP408149R0008 CT terminal mounted kit 400/5A Kit incl. 1 pc. 5VA cl.1 0,61SEP408149R0009 CT terminal mounted kit 600/5A Kit incl. 1 pc. 5VA cl.1 0,61SEP408149R0010 CT terminal mounted kit 600/5A Kit incl. 1 pc. 5VA cl.0,5 0,6NHPL046270R0002 A-meter front cover mounted 100-200/5A 0,2NHPL046270R0001 A-meter front cover mounted 200-400/5A 0,2NHPL046265R0001 NH2 Fuse link 400V/100A for CT 0,5NHPL046266R0001 NH2 Fuse link 400V/125A for CT 0,5NHPL046267R0001 NH2 Fuse link 400V/160A for CT 0,5NHPL046268R0001 NH2 Fuse link 400V/200A for CT 0,5

5 NHPL046269R0001 NH2 Fuse link 400V/224A for CT 0,5NHPL046272R0001 NH2 Fuse link 400V/250A for CT 0,5NHPL046273R0001 NH2 Fuse link 400V/315A for CT 0,5NHPL046274R0001 NH2 Fuse link 400V/335A for CT 0,5NHPL046275R0001 NH2 Fuse link 400V/400A for CT 0,5

6 NHSN718050P2525 CT for front mounted A-meter 250/5A 0,1NHSN718050P2540 CT for front mounted A-meter 400/5A 0,1

Accessories XUBM/XLBM00-1001SEP304058R0001 00-100 Cable shroud 0,11SEP304061R0001 00-100 Cable shroud for special clamps 0,11SEP304068R0001 00-100 Label holder 0,11SEP304105R0001 00-100 Phase barrier kit Kit incl. 3 pcs. 0,11SEP304056R0001 00-100 Prism clamp kit Kit incl. 3 pcs. 0,11SEP304067R0001 00-100 Height alignment kit 0,11SEP304060R0001 00-100 Micro switch 0,11SEP304064R0001 00-100 Adapter for 60mm busbar 0,31SEP304066R0001 00-100 Adapter for 185mm busbar 0,4

7 1SEP304065R0001 00-100 Adapter for 185mm busbar, double 0,71SEP304059R0001 00-100 Hooked clamp Kit incl. 3 pcs. 0,1

Common accessoriesNHSN950001P0006 Insulated hexagon key NV6 0,1

8 1SEP407742R0001 Micro switch 6A/150V 0,19 1SEP407742R0002 Auxiliary switch NC 10A/690V 0,1

1SEP407742R0003 Auxiliary switch NO 10A/690V 0,1

5

1

2

8

4

5

6

7

9

3


InLine6. Dimensional drawings

271SEC312022B0201

XUBM00-100 XLBM00-3P-100

XUBM00 XUBM1/2/3

6



281SEC312022B0201

XLBM00-1P XLBM00-3P

6

XLBM1/2/3-1P XLBM1/2/3-3P



291SEC312022B0201

XUBM00-Z

XLBM00-3P-Z XLBM1/2/3-3P-Z

6



301SEC312022B0201

XLBM1/2/3-3P-ZS

6

XLBM1/2/3-3P-Z2S



311SEC312022B0201

Accessories Size 00

6

Cable shroud XUBM Cable shroud XLBM

Cable shroud short

Ammeter house

EFM Label holder



Accessories Size 1/2/3

ABB ASLow Voltage ProductsAutomation Technologies Division

P.O. Box 100, Sentrum, N-3701 Skien, NorwayTel. +47 35 58 25 00 Fax +47 35 58 28 00e-mail: [email protected]

A part of its on-going product improvement, ABB reservesthe right to modify the characteristics or the products des-cribed in this brochure. The information given is not-contractual. For further details please contact the ABBcompany marketing theese products in your country.

1SE

C31

2022

B02

01

May

200

3P

rint:

Ras

mus

sen,

Ski

en

6

Cable shroud XUBM

Cable shroud XLBM

Label holder

Ammeter houseEFM housing


Documents

ABB rastavljacke pruge