A1353-RA Command Mode ed08.pdf

Alcatel BSS

A1353-RA Command Mode

OMC Document

Reference Guide

Release B9

3BK 20900 AAAA PCZZA Ed.08

Status RELEASED

Short title OMC-R Command Mode

All rights reserved. Passing on and copying of this document, useand communication of its contents not permitted without writtenauthorization from Alcatel.

BLANK PAGE BREAK

2 / 98 3BK 20900 AAAA PCZZA Ed.08

Contents

ContentsPreface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Starting Command Mode Sessions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.1 Dedicated Command Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122.2 Implicit Command Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122.3 Explicit Command Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3 Command Mode Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153.1 OMC Domain Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.1.1 OMC_display() . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163.1.2 OMC_exportRadio( repositoryId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163.1.3 OMC_exportHW( bssId, repositoryId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.2 BSS Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173.2.1 OMC_listBSS() . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173.2.2 OMC_declareBSS( bssUserLabel, supervisionHostName, release, generation,

nodeId, primaryNSAP, secondaryNSAP, preferredLocalAccessPoint,secondaryLocalAccessPoint, OAD, OMCBSSsynchronization ) . . . . . . . . . . . . . 17

3.2.3 OMC_removeBSS( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193.2.4 OMC_forceRemoveBSS( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193.2.5 OMC_bscAndCellsIdle () . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193.2.6 OMC_updateLSAs () . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193.2.7 BSS_lock( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203.2.8 BSS_unlock( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203.2.9 BSS_shutdown( bssId, wtc ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203.2.10 BSS_discover( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213.2.11 BSS_blockingDiscover( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223.2.12 BSS_moveBSC( bssId, newBssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233.2.13 BSS_display( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243.2.14 BSS_enableDLSBackup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243.2.15 BSS_disableDLSBackup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253.2.16 BSS_resynchronizeGPRS(bssId) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253.2.17 BSS_reinitializeGPRS(bssId) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

3.3 PMC Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263.3.1 PMC_display( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263.3.2 PMC_lock( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263.3.3 PMC_unlock( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

3.4 ODMC Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283.4.1 Buffer_displayCellList() . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283.4.2 Buffer_setCellList() . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283.4.3 Buffer_setCellList( cellListName [, cellId n ] ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293.4.4 Buffer_displayRawTypeList() . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293.4.5 Buffer_setRawTypeList() . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303.4.6 Buffer_setRawTypeList( rawTypeListName [, rawType ] ) . . . . . . . . . . . . . . . . . . . 303.4.7 BSS_listNetworkElement( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303.4.8 BSS_listODMC( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313.4.9 BSS_createODMC( bssId, NewODMCName, StartDateTime, StopDateTime,

AccumulationPeriodValue, AccumulationPeriodUnit, SampleRate ) . . . . . . . . . 323.4.10 BSS_deleteODMC( bssId, odmcName ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323.4.11 ODMC_display( bssId, odmcName ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333.4.12 ODMC_modify( bssId, odmcName, NewODMCName, StartDateTime,

StopDateTime, AccumulationPeriodValue, AccumulationPeriodUnit, SampleRate) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

3.4.13 ODMC_lock( bssId, odmcName ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 353.4.14 ODMC_unlock( bssId, odmcName ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

3BK 20900 AAAA PCZZA Ed.08 3 / 98

Contents

3.5 BSC Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363.5.1 BSC_display( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363.5.2 BSC_lockFunction( bssid, SBLType, SBLId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373.5.3 BSC_listFunction( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373.5.4 BSC_displayFunction( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373.5.5 BSC_unlockFunction( bssId, SBLType, SBLId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383.5.6 BSC_generateDownloadSWPackage( bssId, packageName, activateWarning,

applyCDEData ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383.5.7 BSS_deactivateWarning( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383.5.8 TP_lock2MbTTP( bssId, TPType, TPId, BtsId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393.5.9 TP_unlock2MbTTP( bssId, TPType, TPId, BtsId ) . . . . . . . . . . . . . . . . . . . . . . . . . . 393.5.10 TP_display2MbTTP( bssId, TPType, TPId, BtsId ) . . . . . . . . . . . . . . . . . . . . . . . . . 40

3.6 BSC SW Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413.6.1 BSC_displayDLSFile( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413.6.2 BSC_uploadDatabase( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413.6.3 BSC_predownloadBSS_NEProcessors( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . 413.6.4 BSC_displayOperatingSWPackage( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423.6.5 BSC_downloadOperatingSWPackage( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423.6.6 BSC_activateOperatingSWPackage( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423.6.7 BSC_abortOperatingSWPackage( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433.6.8 BSC_acceptOperatingSWPackage( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433.6.9 BSC_rejectOperatingSWPackage( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

3.7 BSC HW Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443.7.1 BSC_listRack( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443.7.2 BSC_listShelf( bssId, rackId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443.7.3 BSC_listCircuitPack( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 453.7.4 BSC_listRackCircuitPack( bssId, rackId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 463.7.5 BSC_listShelfCircuitPack( bssId, rackId, shelfId ) . . . . . . . . . . . . . . . . . . . . . . . . . . 473.7.6 BSC_displayCircuitPack( bssId, rackId, shelfId, slotId ) . . . . . . . . . . . . . . . . . . . . . 483.7.7 BSC_verifyCircuitPack( bssId, rackId, shelfId, slotId ) . . . . . . . . . . . . . . . . . . . . . . 483.7.8 BSC_testCircuitPack( bssId, rackId, shelfId, slotId ) . . . . . . . . . . . . . . . . . . . . . . . . 493.7.9 BSC_lockCircuitPack( bssId, rackId, shelfId, slotId ) . . . . . . . . . . . . . . . . . . . . . . . 493.7.10 BSC_shutdownCircuitPack( bssId, rackId, shelfId, slotId, wtc ) . . . . . . . . . . . . . . 493.7.11 BSC_unlockCircuitPack( bssId, rackId, shelfId, slotId ) . . . . . . . . . . . . . . . . . . . . . 503.7.12 BSC_reset( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 503.7.13 BSC_resetCircuitPack( bssId, rackId, shelfId, slotId ) . . . . . . . . . . . . . . . . . . . . . . 503.7.14 BSC_restart( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 503.7.15 BSC_restartCircuitPack( bssId, rackId, shelfId, slotId ) . . . . . . . . . . . . . . . . . . . . . 51

3.8 TC Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 523.8.1 TC_listRack( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 523.8.2 TC_listShelf( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 523.8.3 TC_listCircuitPack( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 523.8.4 TC_listRackCircuitPack( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 523.8.5 TC_listShelfCircuitPack( bssId, rackId, shelfId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . 523.8.6 TC_displayCircuitPack( bssid, rackId, shelfId, slotId ) . . . . . . . . . . . . . . . . . . . . . . 533.8.7 TC_lockCircuitPack( bssId, rackId, shelfId, slotId ) . . . . . . . . . . . . . . . . . . . . . . . . . 533.8.8 TC_unlockCircuitPack( bssId, rackId, shelfId, slotId ) . . . . . . . . . . . . . . . . . . . . . . . 53

3.9 BTS Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 543.9.1 BSC_listBTS( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 543.9.2 BTS_display( bssId, btsId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 553.9.3 BTS_lockOMCapability( bssId, btsId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 563.9.4 BTS_unlockOMCapability( bssId, btsId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 573.9.5 BTS_listRack( bssId, btsId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 573.9.6 BTS_listShelf( bssId, btsId, rackId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 573.9.7 BTS_listCircuitPack( bssId, btsId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 583.9.8 BTS_listRackCircuitPack( bssId, btsId, rackId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 593.9.9 BTS_listShelfCircuitPack( bssId, btsId, rackId, shelfId ) . . . . . . . . . . . . . . . . . . . . 60

4 / 98 3BK 20900 AAAA PCZZA Ed.08

Contents

3.9.10 BTS_displayCircuitPack( bssId, btsId, rackId, shelfId, slotId ) . . . . . . . . . . . . . . . 613.9.11 BTS_lockCircuitPack( bssId, btsId, rackId, shelfId, slotId ) . . . . . . . . . . . . . . . . . . 613.9.12 BTS_shutdownCircuitPack( bssId, btsId, rackId, shelfId, slotId, wtc ) . . . . . . . . 623.9.13 BTS_unlockCircuitPack( bssId, btsId, rackId, shelfId, slotId ) . . . . . . . . . . . . . . . . 623.9.14 BTS_reset( bssId, btsId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 623.9.15 BTS_resetCircuitPack( bssId, btsId, rackId, shelfId, slotId ) . . . . . . . . . . . . . . . . . 633.9.16 BTS_displayRSL( bssId, btsId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 643.9.17 BTS_restart( bssId, btsId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 653.9.18 BTS_restartCircuitPack( bssId, btsId, rackId, shelfId, slotId ) . . . . . . . . . . . . . . . . 653.9.19 BTS_listSector( bssId, btsId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 653.9.20 Sector_display( bssId, btsId, sectorId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 663.9.21 OMU_display( bssId, btsId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 663.9.22 OMU_reset( bssId, btsId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 673.9.23 OMU_restart( bssId, btsId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

3.10 Cell Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 683.10.1 OMC_listCell() . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 683.10.2 Cell_display("cellId") . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 693.10.3 Cell_lock("cellId") . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 693.10.4 Cell_shutdown("cellId", wtc ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 703.10.5 Cell_unlock("cellId") . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 703.10.6 Cell_bar("cellId") . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 703.10.7 Cell_debar("cellId") . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 703.10.8 Cell_resynchronizeGPRS("cellId") . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 713.10.9 Cell_reinitializeGPRS("cellId") . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

3.11 MFS Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 723.11.1 OMC_listMFS() . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 723.11.2 OMC_activateMFSs() . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 723.11.3 MFS_resynchronize( mfsId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 723.11.4 MFS_ExportGb ( mfsId, dir ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

3.12 PRC Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 733.12.1 OMC_listPRC() . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 733.12.2 OMC_createPRC( prcName, prcDescription, prcAccessRight ) . . . . . . . . . . . . . 733.12.3 OMC_createPRCWithCreatorDate ( prcName, prcDescription, prcAccessRight,

prcCreator, prcLastModifDate ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 733.12.4 OMC_deletePRC( prcName ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 743.12.5 PRC_display( prcName ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 743.12.6 PRC_exportRadio( prcName, repositoryId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 743.12.7 PRC_importRadio( prcName, repositoryId, cgiModeSt ) . . . . . . . . . . . . . . . . . . . . 753.12.8 PRC_activate( prcName, activationMode, cellCleanUpMode, triggerMode,

withSynchroSt, wtc ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 763.12.9 PRC_listCell( prcName ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 773.12.10 PRC_displayCell( prcName, cellId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 773.12.11 PRC_activateCell( prcName, cellId, activationMode ) . . . . . . . . . . . . . . . . . . . . . . 783.12.12 PRC_listMFS( prcName ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 793.12.13 OMC_openPRC( prcName ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 793.12.14 OMC_closePRC( prcName ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 793.12.15 OMC_listOpenPRC() . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 803.12.16 OMC_activateMLU() . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 803.12.17 OMC_acceptMLU() . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

3.13 Support Resource Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 813.13.1 BTS_listOML( bssId, btsId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 813.13.2 BTS_listRSL( bssId, btsId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 813.13.3 RSL_lock( bssId, btsId, rslId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 823.13.4 RSL_shutdown( bssId, btsId, rslId, wtc ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 823.13.5 RSL_unlock( bssId, btsId, rslId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 823.13.6 BSS_listGSL( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 833.13.7 BSS_listTrailR1( bssId, tpId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

3BK 20900 AAAA PCZZA Ed.08 5 / 98

Contents

3.13.8 TrailR1_display( bssId, tpId, timeSlotId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 853.13.9 TrailR1_lock( bssId, tpId, timeSlotId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 853.13.10 TrailR1_shutdown( bssId, tpId, timeSlotId, wtc ) . . . . . . . . . . . . . . . . . . . . . . . . . . . 863.13.11 TrailR1_unlock( bssId, tpId, timeSlotId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 863.13.12 TrailR1_tcLoopOpen( bssId, tpId, timeSlotId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 863.13.13 TrailR1_tcLoopClose( bssId, tpId, timeSlotId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 873.13.14 N7_lock( bssId, N7Id ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 873.13.15 N7_unlock( bssId, N7Id ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 873.13.16 N7_verify( bssId, N7Id ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 873.13.17 N7_listN7( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 883.13.18 N7_displayN7( bssId, N7Id ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

3.14 Function Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 903.14.1 BTS_listFU( bssId, btsId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 903.14.2 FU_display( bssId, btsId, fuId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 903.14.3 FU_lock( bssId, btsId, fuId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 913.14.4 FU_unlock( bssId, btsId, fuId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 913.14.5 FU_reset( bssId, btsId, fuId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 913.14.6 FU_restart( bssId, btsId, fuId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 913.14.7 BTS_listTRE( bssId, btsId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 923.14.8 TRE_display( bssId, btsId, treId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 923.14.9 TRE_lock( bssId, btsId, treId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 933.14.10 TRE_unlock( bssId, btsId, treId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 933.14.11 TRE_reset( bssId, btsId, treId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 933.14.12 TRE_restart( bssId, btsId, treId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

3.15 Audit Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 943.15.1 BSS_hardwareAudit( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 943.15.2 BSC_hardwareAudit( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 943.15.3 BTS_hardwareAudit( bssId, btsId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 943.15.4 BSS_alarmStateAudit( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 943.15.5 BSC_alarmStateAudit( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 953.15.6 BTS_alarmStateAudit( bssId, btsId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 953.15.7 BSS_softwareAudit( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 953.15.8 BSS_PMAudit( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 953.15.9 BSS_traceAudit( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 963.15.10 BSS_LogicalAudit( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 963.15.11 BSC_LogicalAudit( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 963.15.12 Cell_LogicalAudit( CellId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 963.15.13 MFS_alarmAudit( mfsId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

3.16 Query Adiacensies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 983.16.1 Sc_queryAdjacenciesInconsistencies() . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 983.16.2 BSC_queryAdjacenciesInconsistencies( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . . . 983.16.3 Sc_CorrectAdjacenciesInconsistencies() . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 983.16.4 BSC_CorrectAdjacenciesInconsistencies( bssId ) . . . . . . . . . . . . . . . . . . . . . . . . . 98

6 / 98 3BK 20900 AAAA PCZZA Ed.08

Preface

PrefacePurpose This user guide describes how to use Command Mode from the OMC-R.

All available commands are described.

Whats New In Edition 08Improvements were made in following sections due to system behavior:

PRC_listCell( prcName ) (Section 3.12.9)PRC_displayCell( prcName, cellId ) (Section 3.12.10)

In Edition 07First page updated by removing the from MR2 part.

In Edition 06Update the following command lines:

PRC_importRadio( prcName, repositoryId, cgiModeSt ) (Section 3.12.7)PRC_activate( prcName, activationMode, cellCleanUpMode, triggerMode,withSynchroSt, wtc ) (Section 3.12.8)

Add new command lines:

OMC_bscAndCellsIdle () (Section 3.2.5)OMC_updateLSAs () (Section 3.2.6)OMC_createPRCWithCreatorDate ( prcName, prcDescription,

prcAccessRight, prcCreator, prcLastModifDate ) (Section 3.12.3)MFS_ExportGb ( mfsId, dir ) (Section 3.11.4)

In Edition 05Update command OMC_declareBSS( bssUserLabel, supervisionHostName,release, generation, nodeId, primaryNSAP, secondaryNSAP,preferredLocalAccessPoint, secondaryLocalAccessPoint, OAD,OMCBSSsynchronization ) (Section 3.2.2) .

In Edition 04

3BK 20900 AAAA PCZZA Ed.08 7 / 98

Preface

New commands are introduced:

Cell_resynchronizeGPRS("cellId") (Section 3.10.8)Cell_reinitializeGPRS("cellId") (Section 3.10.9)BSS_resynchronizeGPRS(bssId) (Section 3.2.16)BSS_reinitializeGPRS(bssId) (Section 3.2.17)MFS_resynchronize( mfsId ) (Section 3.11.3)

Commands in Cell Management (Section 3.10) were revised.

In Edition 03Automatic Enable/Disable DLS backup. Two new chapters introduced:BSS_enableDLSBackup (Section 3.2.14) , BSS_disableDLSBackup(Section 3.2.15)Command Mode remarks. Updates in N7_listN7( bssId )(Section 3.13.17) , N7_displayN7( bssId, N7Id ) (Section 3.13.18), Sc_queryAdjacenciesInconsistencies() (Section 3.16.1) ,BSC_queryAdjacenciesInconsistencies( bssId ) (Section 3.16.2) andBTS_displayRSL( bssId, btsId ) (Section 3.9.16)

In Edition 02Global correction: delete the space between function name and the parenthesis.Add Tip (in section 1) : the spaces used to separate the command parametersare optional.Add wtc parameter to BSS_shutdown( bssId, wtc ) (Section 3.2.9) .Add () to Sc_queryAdjacenciesInconsistencies() (Section 3.16.1) .Add 2 new commands:

OMC_acceptMLU() (Section 3.12.17)OMC_activateMFSs() (Section 3.11.2) .

In Edition 01Creation.

Audience This user guide is intended for users of the Command Mode procedures.

Assumed Knowledge The reader must be familiar with UNIX System.

8 / 98 3BK 20900 AAAA PCZZA Ed.08

1 Introduction

1 Introduction

This chapter provides an overview of Command Mode:

Command Mode Sessions

Scripts

Access Rights

Errors

Available Commands.

Overview Command Mode allows you to:

Run a series of procedures

Schedule procedures to run at a given date and time

Perform migrations (BSS, A1353-RA/A1353-RA)Command Mode for the A1353-RA allows operators to perform various tasks inDCN, RNUSM and BSSUSM from a unitary and dedicated terminal window.Through this single interface, requests are made by the operator with any UNIXshell script language. Everything you can do in a UNIX environment, you cando in Command Mode. Common functions such as saving, deleting, printing,copying, viewing, editing, renaming and scheduling are performed usingstandard UNIX commands (cp, mv, rm, lp, crontab, at).

Command Mode Options Depending on your needs, you can use Command Mode in three different ways:

Dedicated Command Mode, for running procedures immediately

Implicit Command Mode, for creating files and scheduling Command Modeprocedures to be run at a later time

Explicit Command Mode, for scheduling Command Mode procedures to runwithin other sessions (for example, while performing migrations).

3BK 20900 AAAA PCZZA Ed.08 9 / 98

1 Introduction

Access Rights The Command Mode interface can be started from the desktop by any operatorwith Command Mode access rights. Once Command Mode is started, there isfurther access control. All available commands can be entered according to theOAD (Object Access Domain) or the FAD (Functional Access Domain) accessrights, which are created for each operator by the System Administrator.

Tip The spaces, used to separate the parameters of the commands, are optional.They do not impact the command execution.For example, the following 2 lines are equivalent (both lines are correct):

omcdo -cmd OMC_exportHW(101,1) omcdo -cmd OMC_exportHW( 101, 1 )

Errors If errors occur (parsing, routing, connection failure, or an actual "crash"), errormessages are displayed. The operator can stop and restart the CommandMode session.

10 / 98 3BK 20900 AAAA PCZZA Ed.08

2 Starting Command Mode Sessions


This chapter explains how to start Command Mode sessions.

3BK 20900 AAAA PCZZA Ed.08 11 / 98


2.1 Dedicated Command ModeTo start a Dedicated Command Mode session:1. In the A1353-RA iconbox click the [ Command Mode Session ] icon.

The Command Mode Session window opens.2. Enter

omcdo -start

Depending on what you want to do, choose the right :

OAM : Operation, Administration and Maintenance

EML : Element Management Layer

RNL : Radio Network Layer

MFS : Multi-BSS Fast packet Server.

3. Enteromcdo -cmd

Command Mode runs the procedure(s).4. Enter

omcdo -stop

The used to start the command mode session:

OAM

EML

RNL

MFS

5. Enteromcdo -exit

to exit Command Mode.

Note: Use single and not double quotation marks to enclose the command.Frequently double quotation marks are used within the command string itself. Ifyou have used double quotation marks for the command, you must thenre-enter the command between backslashes.

2.2 Implicit Command ModeUse Implicit Command Mode if you want to create a file and scheduleCommand Mode procedures to run at a later time.1. Create an executable file whith the following content:

omcmdo -start Depending on what you want to do,choose the right :





12 / 98 3BK 20900 AAAA PCZZA Ed.08


omcdo -cmd

omcdo -stop The is that choosed to start thecommand mode session:





2. From any terminal window, enter/alcatel/omc3/usmcmd/script/run_usmcmd -f

The Implicit Command Mode file is created. The file will run the proceduresat the predetermined time, and exit automatically.

2.3 Explicit Command ModeTo create an Explicit Command Mode session file:1. From any terminal, enter

/alcatel/omc3/usmcmd/script/run_usmcmd -p &Command Mode assigns a port number.

PORT =

2. Enterexport USMCMD_SESSION_PORT =

where is the assigned port number.3. Enter

run_omcdo -start

Depending on what you want to do, choose the right :





4. Enterrun_omcdo -cmd

5. Enterrun_omcdo -exit

when you have finished entering commands.The Explicit Command Mode file is created. The file runs the procedureswithin the other session.

Note: Use single and not double quotation marks to enclose the command.Frequently double quotation marks are used within the command string itself. Ifyou have used double quotation marks for the command, you must thenre-enter the command between backslashes.

3BK 20900 AAAA PCZZA Ed.08 13 / 98


14 / 98 3BK 20900 AAAA PCZZA Ed.08

3 Command Mode Commands


This chapter lists the commands available for running procedures.

3BK 20900 AAAA PCZZA Ed.08 15 / 98


3.1 OMC Domain ManagementThis section gives the list of high-level services involved in domain management.

3.1.1 OMC_display()Input None

Output DONE_WITH_INFO

Example COMMAND_MODE>omcdo -cmd OMC_display()DONE_WITH_INFO

ActivationMode: MessageMode

NodeIdentifier: 0

ProceduralStatus: { Reporting }

END_OF_REPORT

3.1.2 OMC_exportRadio( repositoryId )Input repositoryId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd OMC_exportRadio(1)DONE

3.1.3 OMC_exportHW( bssId, repositoryId )Input bssId: Integer

repositoryId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd OMC_exportHW(101,1)DONE

16 / 98 3BK 20900 AAAA PCZZA Ed.08


3.2 BSS ManagementThis section gives the list of high-level services involved in general BSSmanagement.

3.2.1 OMC_listBSS()Input None


Example COMMAND_MODE> omcdo -cmd OMC_listBSS()DONE_WITH_INFO

102 - UserLabel: BSS_102



END_OF_REPORT

3.2.2 OMC_declareBSS( bssUserLabel, supervisionHostName,release, generation, nodeId, primaryNSAP, secondaryNSAP,

3BK 20900 AAAA PCZZA Ed.08 17 / 98


preferredLocalAccessPoint, secondaryLocalAccessPoint, OAD,OMCBSSsynchronization )

Input bssUserLabel: String or None constant (Optional)supervisionHostName: String

release: String ("B8" or "B9")generation: String "G2"

nodeId: Integer or None constant (Optional)primaryNSAP: Integer

secondaryNSAP: Integer or None constant (Optional)preferredLocalAccessPoint: Integer or None constant (i.e. Optional).secondaryLocalAccessPoint: Integer or None constant (i.e. Optional).OAD: String or None constant (Optional)OMCBSSsynchronization: String among ("yes" | "no") or None constant (Optional)

Output Nominal case:DONE_WITH_INFO

Error cases:

ERRORError Code: oam-12Error Description: Problem with system configuration.The BSS identified by is not in a coherent state,you should forceRemove it.END_OF_ERROR_REPORTWhere is the BSS identifier which declaration failed.

ERRORBad generation: enter G2 or EvolutionEND_OF_ERROR_REPORT

Example Nominal case:COMMAND_MODE> omcdo -cmd OMC_declareBSS("Nieuport5","sun5","B9","G2", 10,"123",None,None,None)DONE_WITH_INFO5END_OF_REPORT

Error case:COMMAND_MODE> omcdo -cmdOMC_declareBSS("test_B9","angelus","B9",4,"1234",None,None,None,None,"no")ERRORError Code: oam-12Error Description: Problem with system configuration. The BSSidentified by 5 is not in a coherent state, you should forceRemoveit.END_OF_ERROR_REPORT

18 / 98 3BK 20900 AAAA PCZZA Ed.08


3.2.3 OMC_removeBSS( bssId )Input bssId: Integer

Output DONE

Example Nominal case:COMMAND_MODE> omcdo -cmd OMC_removeBSS( 5 )DONE

Immediate error case:COMMAND_MODE> omcdo -cmd OMC_removeBSS( 5 )ERRORRemove not allowed : the BSC is reserved in SC. Try the ForceRemove menu.END_OF_ERROR_REPORT

3.2.4 OMC_forceRemoveBSS( bssId )Input bssId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd OMC_forceRemoveBSS( 5 )DONE

3.2.5 OMC_bscAndCellsIdle ()Note: This command is used only for migration purpose.

Input None.


Example COMMAND_MODE> omcdo -cmd " OMC_bscAndCellsIdle ()"DONE_WITH_INFOOKEND_OF_REPORT

3.2.6 OMC_updateLSAs ()Note: This command is used only for migration purpose.

3BK 20900 AAAA PCZZA Ed.08 19 / 98


Input None.

Output DONE

Example COMMAND_MODE> omcdo -cmd " OMC_updateLSAs ()"DONE

3.2.7 BSS_lock( bssId )Input bssId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BSS_lock( 5 )DONE

3.2.8 BSS_unlock( bssId )Input bssId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BSS_unlock( 5 )DONE

3.2.9 BSS_shutdown( bssId, wtc )Input bssId: Integer

wtc: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BSS_shutdown( 5, 1)DONE

20 / 98 3BK 20900 AAAA PCZZA Ed.08


3.2.10 BSS_discover( bssId )Input bssId: Integer

Output DONEThis is a non-blocking version of discover BSS function.

Example COMMAND_MODE> omcdo -cmd BSS_discover( 101 )DONE

3BK 20900 AAAA PCZZA Ed.08 21 / 98


3.2.11 BSS_blockingDiscover( bssId )Input bssId: Integer

Output DONE_WITH_INFOThis is a blocking version of discover BSS function. It enables to get a more completeinformation result report, but the user has to wait until the whole discover processcompletion.

Example COMMAND_MODE> omcdo -cmd BSS_blockingDiscover(101)DONE_WITH_INFO

Discover Bss-BSS 101 - BSS_101

Started

Ended

Audit hardware and alarm-BSS 101 - BSS_101

Started

Ended

Audit software-BSS 101 - BSS_101

Started

Ended

Audit PM-BSS 101 - BSS_101

Started

Ended

AuditRadio-BSS 101 - BSS_101

Started

Ended

AuditPeerEntity-BSS 101 - BSS_101

Started

Ended

AuditTrace-BSS 101 - BSS_101

Started

Ended

END_OF_REPORT

22 / 98 3BK 20900 AAAA PCZZA Ed.08


3.2.12 BSS_moveBSC( bssId, newBssId )Input bssId: Integer. Id of the source BSS.

newBssId : String. Id of the target BSS.

Output DONEThis function produces the EML export files bssId.apd.bsc and bssId.bssName.odmc,where bssId is the identifier of the source BSS and bssName is the name of this BSS.

Example COMMAND_MODE> omcdo -cmd BSS_moveBSC(101,"102")DONE

3BK 20900 AAAA PCZZA Ed.08 23 / 98


3.2.13 BSS_display( bssId )Input bssId: Integer


Example COMMAND_MODE> omcdo -cmd BSS_display(102)DONE_WITH_INFO

AdministrativeState: Locked

AlarmStatus: Cleared

AlarmStatusSynthesis: Cleared

AlignmentStatus: Aligned

BSC_Generation: G2

BSS_Release: B9

CurrentSessionStatus: NoSession

MfsAdministrativeState: Locked

MfsAlarmStatus: Cleared

MfsAlignmentStatus: Aligned

MfsAvailabilityStatus: { }

MfsOperationalState: Enabled

MluProgressionStatus: Idle

OperationalState: Enabled

ReplacementJobStatus: Idle

ReservationStatus: Idle

RnlAlcatelBSCID: 102

SMSCB_STATE: Enabled

SwPackageProductionStatus: Idle

TchUsageInfoPeriod: 50

TranscodingCapability: Multi_rate

UnknownStatus: No

UserLabel: BSS_102

END_OF_REPORT

3.2.14 BSS_enableDLSBackup

Input bssId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BSS_enableDLSBackup(1)DONE

24 / 98 3BK 20900 AAAA PCZZA Ed.08


3.2.15 BSS_disableDLSBackup


Output DONE

Example COMMAND_MODE> omcdo -cmd BSS_disableDLSBackup(1)DONE

3.2.16 BSS_resynchronizeGPRS(bssId)Input bssId: Integer


Example COMMAND_MODE>omcdo -cmd BSS_reinitializeGPRS(1)DONE_WITH_INFODONEEND_OF_REPORT

3.2.17 BSS_reinitializeGPRS(bssId)Input bssId: Integer


Example COMMAND_MODE>omcdo -cmd BSS_reinitializeGPRS(1)DONE_WITH_INFODONEEND_OF_REPORT

3BK 20900 AAAA PCZZA Ed.08 25 / 98


3.3 PMC ManagementThis section gives the list of high-level services involved in PMC management.Note only one PMC is present in OMC, so its naming is implicit.

3.3.1 PMC_display( bssId )Input bssId: Integer


Example COMMAND_MODE> omcdo -cmd PMC_display(102)DONE_WITH_INFO

AdministrativeState: locked

AvailabilityStatus: { offDuty }

MeasurementFunctionList: { cellTrxRelatedOverviewCnt79T110 }

Minutes: 30

OperationalState: enabled

ScannerType: permanent

UserLabel: PMC

Xnumber: 1

Recording Intervals

StartTime1: 09:00

StopTime1: 10:00

StartTime2: 14:00

StopTime2: 16:00

Measurement Functions:

Overview measurements

END_OF_REPORT

3.3.2 PMC_lock( bssId )Input bssId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd PMC_lock(102)DONE

26 / 98 3BK 20900 AAAA PCZZA Ed.08


3.3.3 PMC_unlock( bssId )Input bssId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd PMC_unlock(102)DONE

3BK 20900 AAAA PCZZA Ed.08 27 / 98


3.4 ODMC ManagementThis section describes the list of high-level services involved in ODMCmanagement. Note that ODMC management requires manipulation of elementlists (cell & raw types). Therefore, this list must be fully informed in a bufferbefore any ODMC creation/modification.Also note that each subsequent Buffer_xxx function is only a buffer accessor.This means that no check is made at this level regarding associatedinformation set in the buffer. The actual checks will be performed by thecreation/modification functions themselves.

3.4.1 Buffer_displayCellList()Input None

Output DONE_WITH_INFOThere is a difference between the two following output cases:

A previous call of Buffer_setCellList(cellListName) (with an empty cellId list) setsan empty cellId list and gives a Buffer_displayCellList() output such as:DONE_WITH_INFOEND_OF_REPORT

A previous call of Buffer_setCellList() sets the buffer to "No cell change required"state and gives a Buffer_displayCellList() output such as:DONE_WITH_INFONO LISTEND_OF_REPORT

Example COMMAND_MODE> omcdo -cmd Buffer_displayCellList()DONE_WITH_INFO

33-33

44-44

END_OF_REPORT

3.4.2 Buffer_setCellList()Input None

Output DONEUsing this function means no cell change required.

Example COMMAND_MODE> omcdo -cmd Buffer_setCellList()DONE

28 / 98 3BK 20900 AAAA PCZZA Ed.08


3.4.3 Buffer_setCellList( cellListName [, cellId n ] )Input cellListName: String

cellId n: String. "lac-ci" string Id of the nth cell

Output DONEThis function enables to set a cell list in the buffer, from 0 to n elements, givingas much cellId information as required to identify every cell object. (Here, the [] symbols are only used to show the optional and iterative aspects of the cellIdparameter pattern).

Example COMMAND_MODE> omcdo -cmd Buffer_setCellList("cellList1", "33-33","44-44")

DONE

3.4.4 Buffer_displayRawTypeList()Input None

Output DONE_WITH_INFOThere is a difference between the two following output cases:

A previous call of Buffer_setRawTypeList(rawTypeListName) (with an emptyrawType list) sets an empty rawType list and gives a Buffer_displayRawTypeList()output such as:DONE_WITH_INFOEND_OF_REPORT

A previous call of Buffer_setRawTypeList () sets the buffer to "No raw type changerequired" state and gives a Buffer_displayRawTypeList () output such as:DONE_WITH_INFONO LISTEND_OF_REPORT

Example COMMAND_MODE> omcdo -cmd Buffer_displayRawTypeList()DONE_WITH_INFO

110

100

END_OF_REPORT

3BK 20900 AAAA PCZZA Ed.08 29 / 98


3.4.5 Buffer_setRawTypeList()Input None

Output DONEUsing this function means no raw type change required.

Example COMMAND_MODE> omcdo -cmd Buffer_setRawTypeList()DONE

3.4.6 Buffer_setRawTypeList( rawTypeListName [, rawType ] )Input rawTypeListName: String

rawType: IntegerThis function enables to set a raw type list in the buffer, from 0 to n elements.Here, the [ ] symbols are only used to show the optional and iterative aspects ofthe rawType parameter pattern.

Output DONE

Example COMMAND_MODE> omcdo -cmd Buffer_setRawTypeList("rawTypList1", 110,100)

DONE

3.4.7 BSS_listNetworkElement( bssId )Input bssId: Integer


Example COMMAND_MODE> omcdo -cmd BSS_listNetworkElement(102)DONE_WITH_INFO

cell00033_00033: 33-33

END_OF_REPORT

30 / 98 3BK 20900 AAAA PCZZA Ed.08


3.4.8 BSS_listODMC( bssId )Input bssId: Integer


Example COMMAND_MODE> omcdo -cmd BSS_listODMC(102)DONE_WITH_INFO

odmc1

odmc2

odmc3

END_OF_REPORT

3BK 20900 AAAA PCZZA Ed.08 31 / 98


3.4.9 BSS_createODMC( bssId, NewODMCName, StartDateTime,StopDateTime, AccumulationPeriodValue,AccumulationPeriodUnit, SampleRate )


NewODMCName: String

StartDateTime: DateTime String. DateTime String format is detailed below

StopDateTime: DateTime String. DateTime String format is detailed below

AccumulationPeriodValue: Integer

AccumulationPeriodUnit: Constant, with a value taken among (HOUR, MINUTE)constant set

sampleRate: IntegerDateTime string format is defined as follows:"Year/Month/Day Hour:Minutes" with:

Integer Year,

Integer[1,12] Month,Integer[1,31] Day,Integer[0,23] Hour,Integer[0,59] Minutes.

Note that the previously described DateTime format must be strictly adhered to,otherwise there is no guarantee as to what effective DateTime value will be takeninto account.Also note that the current Cell List and RawType List buffers contents are implicit butactual BSS_createODMC parameters.

Output DONE

Example COMMAND_MODE> omcdo -cmd BSS_createODMC(102, "odmc20", "2001/02/2611:00", "2001/02/26 13:00", 2, HOUR, 22)

DONE

3.4.10 BSS_deleteODMC( bssId, odmcName )Input bssId: Integer

odmcName: String

Output DONE

Example COMMAND_MODE> omcdo -cmd BSS_deleteODMC(102, "odmc24")DONE

32 / 98 3BK 20900 AAAA PCZZA Ed.08


3.4.11 ODMC_display( bssId, odmcName )Input bssId: Integer

odmcName: String


Example COMMAND_MODE> omcdo -cmd ODMC_display(102,"odmc2")DONE_WITH_INFO

AdministrativeState: locked

AvailabilityStatus: { offDuty }

Hours: 10

MeasurementFunctionList: { trafficMeasCnt47T01 }

OperationalState: enabled

SampleRate: 27

ScannerType: onDemand

UserLabel: odmc2

Xnumber: 4

StartTime: 2001/02/25 10:00:00

StopTime: 2001/02/25 20:00:00

Measurement Functions :

Traffic measurements

NetworkElementList

cell00033_00033: 33-33

END_OF_REPORT

3BK 20900 AAAA PCZZA Ed.08 33 / 98


3.4.12 ODMC_modify( bssId, odmcName, NewODMCName,StartDateTime, StopDateTime, AccumulationPeriodValue,AccumulationPeriodUnit, SampleRate )


odmcName: String

NewODMCName: String

StartDateTime: DateTime String. DateTime String format is detailed below

StopDateTime: DateTime String. DateTime String format is detailed below

AccumulationPeriodValue: Integer

AccumulationPeriodUnit: Constant, with a value taken among (HOUR, MINUTE)constant set

sampleRate: IntegerDateTime string format is defined as follows:"Year/Month/Day Hour:Minutes" with:

Integer Year,

Integer[1,12] Month,Integer[1,31] Day,Integer[0,23] Hour,Integer[0,59] Minutes.

Note that the previously described DateTime format must be strictly adhered to,otherwise there is no guarantee as to what effective DateTime value will be takeninto account.Also note that the current Cell List and RawType List buffers contents are implicit butactual BSS_createODMC parameters.

Output DONE

Example COMMAND_MODE> omcdo -cmd ODMC_modify(102, "odmc20", "odmc20","2001/02/27 00:00", "2001/02/27 10:00", 10, HOUR, 10)

DONE

34 / 98 3BK 20900 AAAA PCZZA Ed.08


3.4.13 ODMC_lock( bssId, odmcName )Input bssId: Integer

odmcName: String

Output DONE

Example COMMAND_MODE> omcdo -cmd ODMC_lock(102, "odmc21")DONE

3.4.14 ODMC_unlock( bssId, odmcName )Input bssId: Integer

odmcName: String

Output DONE

Example COMMAND_MODE> omcdo -cmd ODMC_unlock(102, "odmc22")DONE

3BK 20900 AAAA PCZZA Ed.08 35 / 98


3.5 BSC ManagementThis section gives the list of high-level services involved in BSC management.Note only one BSC is present in a BSS, so its naming is implicit per BSS.

3.5.1 BSC_display( bssId )Input bssId: Integer


Example COMMAND_MODE> omcdo -cmd BSC_display(101)DONE_WITH_INFO

AManagedElementReservedForTest: No

AdministrativeState: Unlocked


AvailabilityStatus: { }

ControlStatus: { }

EquipmentIdNumericName: 1

EquipmentType: bsc

ManagedElementIdNumericName: 1


UnAcknowledgedAlarm: No

UnknownStatus: No

UserLabel: BSS_101

UserMemo:


BSS_Release: B9

WTC: 0

AtrkSign_Nbr: 10

AtrkTraf_Nbr: 40

BSC_Generation: g2

BSC_HW_Config: Config 3

GSM_PHASE: Phase 2

LocationName: bss1--C001

VersionOfOMC_BSCInterface: 50

END_OF_REPORT

36 / 98 3BK 20900 AAAA PCZZA Ed.08


3.5.2 BSC_lockFunction( bssid, SBLType, SBLId )Input bssId: Integer

SBLType can be:

DISC

X25

TR-O&M

SBLId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BSC_lockFunction(101, X25, 1)

3.5.3 BSC_listFunction( bssId )Input bssId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BSC_listFunction(101)

3.5.4 BSC_displayFunction( bssId )Input bssId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BSC_displayFunction(101)

3BK 20900 AAAA PCZZA Ed.08 37 / 98


3.5.5 BSC_unlockFunction( bssId, SBLType, SBLId )Input bssId: Integer

SBLType can be:

DISC

X25

TR-O&M

SBLId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BSC_unlockFunction(101, X25, 1)

3.5.6 BSC_generateDownloadSWPackage( bssId, packageName,activateWarning, applyCDEData )

Input bssId: Integer. This parameter is mandatory.

packageName: String. This parameter is mandatory.

activateWarning: Boolean (0 or 1). This parameter is optional (default value is 1).applyCDEData: Boolean (0 or 1). This parameter is optional (default value is 1).

Please note that the operator has to specify either none or both optional parameters.In other words, this function accepts either two or four arguments (but not three).

Output DONE

Example COMMAND_MODE> omcdo -cmdBSC_generateDownloadSWPackage(101,"/tmp/SDP/sdp1/package1",1,0)

DONE

3.5.7 BSS_deactivateWarning( bssId )Input bssId: Integer (mandatory).

Output DONE

Example COMMAND_MODE> omcdo -cmd BSS_deactivateWarning(101)DONE

38 / 98 3BK 20900 AAAA PCZZA Ed.08


3.5.8 TP_lock2MbTTP( bssId, TPType, TPId, BtsId )Input bssId: Integer

TPType can be:

Ater

AterMuxBSC

AterMuxTC

AbisBSC

AbisBTS

A

TPid: Integer

BtsID: Integer - needed only for AbisBTS

Output DONE

Example COMMAND_MODE> omcdo -cmd TP_lock2MbTTP(101,AbisBTS,3,15)

3.5.9 TP_unlock2MbTTP( bssId, TPType, TPId, BtsId )Input bssId: Integer

TPType can be:

Ater

AterMuxBSC

AterMuxTC

AbisBSC

AbisBTS

A

TPid: Integer


Output DONE

Example COMMAND_MODE> omcdo -cmd TP_unlock2MbTTP(101,AbisBTS,3,15)

3BK 20900 AAAA PCZZA Ed.08 39 / 98


3.5.10 TP_display2MbTTP( bssId, TPType, TPId, BtsId )Input bssId: Integer

TPType can be:

Ater

AterMuxBSC

AterMuxTC

AbisBSC

AbisBTS

A

TPid: Integer


Output DONE

Example COMMAND_MODE> omcdo -cmd TP_display2MbTTP(101,AbisBTS,3,15)

40 / 98 3BK 20900 AAAA PCZZA Ed.08


3.6 BSC SW ManagementThis section gives the list of high-level services involved in BSC Softwaremanagement.

3.6.1 BSC_displayDLSFile( bssId )Input bssId: Integer


Example COMMAND_MODE> omcdo -cmd BSC_displayDLSFile(101)

3.6.2 BSC_uploadDatabase( bssId )Input bssId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BSC_uploadDatabase(101)DONE

3.6.3 BSC_predownloadBSS_NEProcessors( bssId )Input bssId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BSC_predownloadBSS_NEProcessors(101)

3BK 20900 AAAA PCZZA Ed.08 41 / 98


3.6.4 BSC_displayOperatingSWPackage( bssId )Input bssId: Integer


Example COMMAND_MODE> omcdo -cmd BSC_displayOperatingSWPackage(101)DONE_WITH_INFO

Software Package Version

FileName:

ReplacementLevel::no

AProgress: 0

ActivateStatusReportPeriodicity: 15

AutoRejectAllowed: YesBackupJobStatus: Idle

OperatingSoftwareId: 1

ReplacementJobStatus: Idle

RestartPeriod: 5

RestartThreshold: 20

SoftwarePackageName:

TimeStamp: 2001/02/28 10:04:17

UploadJobStatus: Idle

UserName: cmdModAdmin

END_OF_REPORT

3.6.5 BSC_downloadOperatingSWPackage( bssId )Input bssId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BSC_downloadOperatingSWPackage(101)DONE

3.6.6 BSC_activateOperatingSWPackage( bssId )Input bssId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BSC_activateOperatingSWPackage(101)DONE

42 / 98 3BK 20900 AAAA PCZZA Ed.08


3.6.7 BSC_abortOperatingSWPackage( bssId )Input bssId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BSC_abortOperatingSWPackage(101)DONE

3.6.8 BSC_acceptOperatingSWPackage( bssId )Input bssId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BSC_acceptOperatingSWPackage(101)DONE

3.6.9 BSC_rejectOperatingSWPackage( bssId )Input bssId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BSC_rejectOperatingSWPackage(101)DONE

3BK 20900 AAAA PCZZA Ed.08 43 / 98


3.7 BSC HW ManagementThis section gives the list of high-level services involved in BSC Hardwaremanagement.

3.7.1 BSC_listRack( bssId )Input bssId: Integer


Example COMMAND_MODE> omcdo -cmd BSC_listRack(101)DONE_WITH_INFO

1

2

END_OF_REPORT

3.7.2 BSC_listShelf( bssId, rackId )Input bssId: Integer

rackId: Integer


Example COMMAND_MODE> omcdo -cmd BSC_listShelf(101,1)DONE_WITH_INFO

2

3

4

6

7

8

END_OF_REPORT

44 / 98 3BK 20900 AAAA PCZZA Ed.08


3.7.3 BSC_listCircuitPack( bssId )Input bssId: Integer


Example COMMAND_MODE> omcdo -cmd BSC_listCircuitPack(101)DONE_WITH_INFO

rack:1:shelf:2:board:swch-aa 1:1

rack:1:shelf:2:board:swch-aa 3:3

rack:1:shelf:2:board:dcdc 17:17

rack:1:shelf:3:board:dtcc 13:13

rack:1:shelf:3:board:asmb 21:21

rack:1:shelf:3:board:swch-ab 41:41

rack:1:shelf:3:board:tcuc 45:45

rack:1:shelf:3:board:biua 63:63


rack:1:shelf:4:board:swch-ab 27:27

rack:1:shelf:4:board:dcdc 29:29

rack:1:shelf:4:board:biua 39:39


END_OF_REPORT

This example has been shortened, as the original example was toolong.

3BK 20900 AAAA PCZZA Ed.08 45 / 98


3.7.4 BSC_listRackCircuitPack( bssId, rackId )Input bssId: Integer

rackId: Integer


Example COMMAND_MODE> omcdo -cmd BSC_listRackCircuitPack(101,1)DONE_WITH_INFO

shelf:2:board:swch-aa 1:1

shelf:2:board:dcdc 17:17




shelf:3:board:swch-ab 9:9

shelf:3:board:dtcc 13:13

shelf:3:board:asmb 21:21

shelf:3:board:tcuc 45:45

shelf:3:board:biua 63:63


















shelf:7:board:bcla-aa 57:57

shelf:7:board:bcla-ab 61:61

END_OF_REPORT

This example has beeen shortened, as the original example was toolong.

46 / 98 3BK 20900 AAAA PCZZA Ed.08


3.7.5 BSC_listShelfCircuitPack( bssId, rackId, shelfId )Input bssId: Integer

rackId: Integer

shelfId: Integer


Example COMMAND_MODE> omcdo -cmd BSC_listShelfCircuitPack(101,1,3)DONE_WITH_INFO

board:dcdc 1:1

board:swch-aa 5:5

board:swch-aa 7:7

board:swch-ab 9:9

board:swch-ab 11:11

board:dtcc 13:13

board:dtcc 15:15

board:dtcc 17:17

board:dtcc 19:19

board:asmb 21:21

board:dtcc 23:23

board:dtcc 25:25

board:dtcc 27:27

board:dtcc 29:29

board:asmb 31:31

board:dcdc 33:33

board:swch-aa 37:37

board:swch-aa 39:39

board:swch-ab 41:41

board:swch-ab 43:43

board:tcuc 45:45

board:tcuc 47:47

board:tcuc 49:49

board:tcuc 51:51

board:tcuc 53:53

board:tcuc 55:55

board:tcuc 57:57

board:tcuc 59:59

board:biua 63:63

END_OF_REPORT

3BK 20900 AAAA PCZZA Ed.08 47 / 98


3.7.6 BSC_displayCircuitPack( bssId, rackId, shelfId, slotId )Input bssId: Integer

rackId: Integer

shelfId: Integer

slotId: Integer


Example COMMAND_MODE> omcdo -cmd BSC_displayCircuitPack(101,1,3,15)DONE_WITH_INFO




BtsSector: Station Unit Sharing

CircuitPackSelector: Dummy

CircuitPackType: dtcc

ControlStatus: { }


SlotNumber: 15

SupervisionActionList: { ChangeAdminStateAction, Shutdown,TrigReset, TrigRestart, TrigVerify, TrigTest }

UserLabel: dtcc 15

END_OF_REPORT

3.7.7 BSC_verifyCircuitPack( bssId, rackId, shelfId, slotId )Input bssId: Integer

rackId: Integer

shelfId: Integer

slotId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BSC_verifyCircuitPack(101,1,3,15)DONE

48 / 98 3BK 20900 AAAA PCZZA Ed.08


3.7.8 BSC_testCircuitPack( bssId, rackId, shelfId, slotId )Input bssId: Integer

rackId: Integer

shelfId: Integer

slotId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BSC_testCircuitPack(101,1,3,15)DONE

3.7.9 BSC_lockCircuitPack( bssId, rackId, shelfId, slotId )Input bssId: Integer

rackId: Integer

shelfId: Integer

slotId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BSC_lockCircuitPack(101,1,3,15)DONE

3.7.10 BSC_shutdownCircuitPack( bssId, rackId, shelfId, slotId, wtc )Input bssId: Integer

rackId: Integer

shelfId: Integer

slotId: Integer

wtc: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BSC_shutdownCircuitPack(101,1,3,15,10)DONE

3BK 20900 AAAA PCZZA Ed.08 49 / 98


3.7.11 BSC_unlockCircuitPack( bssId, rackId, shelfId, slotId )Input bssId: Integer

rackId: Integer

shelfId: Integer

slotId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BSC_unlockCircuitPack(101,1,3,15)DONE

3.7.12 BSC_reset( bssId )Input bssId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BSC_reset(101)DONE

3.7.13 BSC_resetCircuitPack( bssId, rackId, shelfId, slotId )Input bssId: Integer

rackId: Integer

shelfId: Integer

slotId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BSC_resetCircuitPack(101,1,3,15)DONE

3.7.14 BSC_restart( bssId )Input bssId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BSC_restart(101)DONE

50 / 98 3BK 20900 AAAA PCZZA Ed.08


3.7.15 BSC_restartCircuitPack( bssId, rackId, shelfId, slotId )Input bssId: Integer

rackId: Integer

shelfId: Integer

slotId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BSC_restartCircuitPack(101,1,3,15)DONE

3BK 20900 AAAA PCZZA Ed.08 51 / 98


3.8 TC Management

3.8.1 TC_listRack( bssId )Input bssId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd TC_listRack(101)

3.8.2 TC_listShelf( bssId )Input bssId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd TC_listShelf(101)

3.8.3 TC_listCircuitPack( bssId )Input bssId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd TC_listCircuitPack(101)

3.8.4 TC_listRackCircuitPack( bssId )Input bssId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd TC_listRackCircuitPack(101)

3.8.5 TC_listShelfCircuitPack( bssId, rackId, shelfId )Input bssId: Integer

rackId: Integer

shelfId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd TC_listShelfCircuitPack(101,1,3)

52 / 98 3BK 20900 AAAA PCZZA Ed.08


3.8.6 TC_displayCircuitPack( bssid, rackId, shelfId, slotId )Input bssId: Integer

rackId: Integer

shelfId: Integer

slotId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd TC_displayCircuitPack(101,1,3,15)

3.8.7 TC_lockCircuitPack( bssId, rackId, shelfId, slotId )Input bssId: Integer

rackId: Integer

shelfId: Integer

slotId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd TC_lockCircuitPack(101,1,3,15)

3.8.8 TC_unlockCircuitPack( bssId, rackId, shelfId, slotId )Input bssId: Integer

rackId: Integer

shelfId: Integer

slotId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd TC_unlockCircuitPack(101,1,3,15)

3BK 20900 AAAA PCZZA Ed.08 53 / 98


3.9 BTS ManagementThis section gives the list of high-level services involved in BTS generalmanagement.

3.9.1 BSC_listBTS( bssId )Input bssId: Integer


Example COMMAND_MODE> omcdo -cmd BSC_listBTS(101)DONE_WITH_INFO

BTS_001:1

BTS_002:2

BTS_003:3

BTS_004:4

BTS_005:5

BTS_006:6

BTS_007:7

BTS_008:8

BTS_009:9

BTS_010:10

END_OF_REPORT

54 / 98 3BK 20900 AAAA PCZZA Ed.08


3.9.2 BTS_display( bssId, btsId )Input bssId: Integer

btsId: Integer


Example COMMAND_MODE> omcdo -cmd BTS_display(101,5)DONE_WITH_INFO

AManagedElementReservedForTest: No




ControlStatus: { }

EquipmentIdNumericName: 7

EquipmentType: bts

ManagedElementIdNumericName: 7


UnAcknowledgedAlarm: No

UnknownStatus: No

UserLabel: BTS_005

UserMemo:


Allow_extendedCellBoolean: Yes

AntennaDiversityHwCapabilityBoolean: No

AntennaDiversityUsageBoolean: No


BTS_CIPH_CAP: { Unknown }

BTS_CIPH_CAPHwCapability: { No, A5/7, A5/6, A5/5, A5/4, A5/3, A5/2,A5/1 }

BTS_GenerationG2: G2 Indoor

BtsSiteManagerID: 5

BtsTransmissionConfigurationMode: QMux

ClockDelay2: 7

ClockDelay3: 7

ClockSynchronizationHwCapability: Pcm & Free running

ClockSynchronizationUsage: Ignore

ControlStatus: { }

CouplingType: Undefined

EmlAlarmStatus: Cleared

3BK 20900 AAAA PCZZA Ed.08 55 / 98


Example FuType: FUCOLocationName: bss1--S005

Max_Bts_Sector: 6

MuxRule: No mux

NodeIdentifier: 0

OmuFirmwareVersion: Unknown

OmuHwVariant: Hw1


PowerSupply: Undefined

RTE_Equipped: No

RackSharing: 0

RadioCarrierType: Mono_frequency

RadioFrontEnd: Undefined

SpeechCodingRate: Dual rate

TSCProvider: Alcatel

UsableTSs: { }

UserLabel: BTS_005

END_OF_REPORT

3.9.3 BTS_lockOMCapability( bssId, btsId )Input bssId: Integer

btsId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BTS_lockOMCapability(101,5)DONE

56 / 98 3BK 20900 AAAA PCZZA Ed.08


3.9.4 BTS_unlockOMCapability( bssId, btsId )Input bssId: Integer

btsId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BTS_unlockOMCapability(101,5)DONE

This section gives the list of high-level services involved in BTS Hardwaremanagement.

3.9.5 BTS_listRack( bssId, btsId )Input bssId: Integer

btsId: Integer


Example COMMAND_MODE> omcdo -cmd BTS_listRack(101,5)DONE_WITH_INFO

1

7

END_OF_REPORT

3.9.6 BTS_listShelf( bssId, btsId, rackId )Input bssId: Integer

btsId: Integer

rackId: Integer


Example COMMAND_MODE> omcdo -cmd BTS_listShelf(101,5,1)DONE_WITH_INFO

3

END_OF_REPORT

3BK 20900 AAAA PCZZA Ed.08 57 / 98


3.9.7 BTS_listCircuitPack( bssId, btsId )Input bssId: Integer

btsId: Integer


Example COMMAND_MODE> omcdo -cmd BTS_listCircuitPack(101,5)DONE_WITH_INFO

rack:1:shelf:3:board:msps 1:1

rack:1:shelf:3:board:msps 2:2

rack:1:shelf:3:board:scfe 3:3

rack:1:shelf:3:board:cfu1 4:4

rack:1:shelf:3:board:cfut 5:5

rack:1:shelf:3:board:sace 6:6

rack:1:shelf:3:board:stse 7:7

rack:1:shelf:3:board:feg2 11:11

rack:1:shelf:3:board:rtsg 12:12

rack:1:shelf:3:board:mbps 13:13

rack:1:shelf:3:board:txgm 14:14

rack:1:shelf:3:board:rxgd 15:15

rack:1:shelf:3:board:drfu 18:18

rack:1:shelf:3:board:cfu1 27:27

rack:1:shelf:3:board:cfut 28:28

rack:1:shelf:3:board:sace 29:29

rack:1:shelf:3:board:stse 30:30

rack:1:shelf:3:board:mbps 36:36

rack:1:shelf:3:board:txgm 37:37

rack:1:shelf:3:board:rxgd 38:38

rack:1:shelf:3:board:drfu 41:41

rack:7:shelf:15:board:smbi 31:31

END_OF_REPORT

58 / 98 3BK 20900 AAAA PCZZA Ed.08


3.9.8 BTS_listRackCircuitPack( bssId, btsId, rackId )Input bssId: Integer

btsId: Integer

rackId: Integer


Example COMMAND_MODE> omcdo -cmd BTS_listRackCircuitPack(101,5,1)DONE_WITH_INFO

shelf:3:board:msps 1:1

shelf:3:board:msps 2:2

shelf:3:board:scfe 3:3

shelf:3:board:cfu1 4:4

shelf:3:board:cfut 5:5

shelf:3:board:sace 6:6

shelf:3:board:stse 7:7

shelf:3:board:feg2 11:11

shelf:3:board:rtsg 12:12

shelf:3:board:mbps 13:13

shelf:3:board:txgm 14:14

shelf:3:board:rxgd 15:15

shelf:3:board:drfu 18:18

shelf:3:board:cfu1 27:27

shelf:3:board:cfut 28:28

shelf:3:board:sace 29:29

shelf:3:board:stse 30:30

shelf:3:board:mbps 36:36

shelf:3:board:txgm 37:37

shelf:3:board:rxgd 38:38

shelf:3:board:drfu 41:41

END_OF_REPORT

3BK 20900 AAAA PCZZA Ed.08 59 / 98


3.9.9 BTS_listShelfCircuitPack( bssId, btsId, rackId, shelfId )Input bssId: Integer

btsId: Integer

rackId: Integer

shelfId: Integer


Example COMMAND_MODE> omcdo -cmd BTS_listShelfCircuitPack(101,5,1,3)DONE_WITH_INFO

board:msps 1:1

board:msps 2:2

board:scfe 3:3

board:cfu1 4:4

board:cfut 5:5

board:sace 6:6

board:stse 7:7

board:feg2 11:11

board:rtsg 12:12

board:mbps 13:13

board:txgm 14:14

board:rxgd 15:15

board:drfu 18:18

board:cfu1 27:27

board:cfut 28:28

board:sace 29:29

board:stse 30:30

board:mbps 36:36

board:txgm 37:37

board:rxgd 38:38

board:drfu 41:41

END_OF_REPORT

60 / 98 3BK 20900 AAAA PCZZA Ed.08


3.9.10 BTS_displayCircuitPack( bssId, btsId, rackId, shelfId, slotId )Input bssId: Integer

btsId: Integer

rackId: Integer

shelfId: Integer

slotId: Integer


Example COMMAND_MODE> omcdo -cmd BTS_displayCircuitPack(101,5,1,3,1)DONE_WITH_INFO




BtsSector: Station Unit Sharing

CircuitPackSelector: Dummy

CircuitPackType: msps

ControlStatus: { }


SlotNumber: 1

SupervisionActionList: { TrigReset, TrigRestart }

UserLabel: msps 1

END_OF_REPORT

3.9.11 BTS_lockCircuitPack( bssId, btsId, rackId, shelfId, slotId )Input bssId: Integer

btsId: Integer

rackId: Integer

shelfId: Integer

slotId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BTS_lockCircuitPack(101,5,1,3,1)DONE

3BK 20900 AAAA PCZZA Ed.08 61 / 98


3.9.12 BTS_shutdownCircuitPack( bssId, btsId, rackId, shelfId, slotId,wtc )


btsId: Integer

rackId: Integer

shelfId: Integer

slotId: Integer

wtc: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BTS_shutdownCircuitPack(101,5,1,3,1,20)DONE

3.9.13 BTS_unlockCircuitPack( bssId, btsId, rackId, shelfId, slotId )Input bssId: Integer

btsId: Integer

rackId: Integer

shelfId: Integer

slotId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BTS_unlockCircuitPack(101,5,1,3,1)DONE

3.9.14 BTS_reset( bssId, btsId )Input bssId: Integer

btsId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BTS_reset(101,5)DONE

62 / 98 3BK 20900 AAAA PCZZA Ed.08


3.9.15 BTS_resetCircuitPack( bssId, btsId, rackId, shelfId, slotId )Input bssId: Integer

btsId: Integer

rackId: Integer

shelfId: Integer

slotId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BTS_resetCircuitPack(101,5,1,3,1)DONE

3BK 20900 AAAA PCZZA Ed.08 63 / 98


3.9.16 BTS_displayRSL( bssId, btsId )Input bssId: Integer

btsId: Integer


Example COMMAND_MODE> omcdo -cmd BTS_displayRSL(1,2)DONE_WITH_INFO




ControlStatus: { }

EGprsHWCapability: Cs1cs2

FrequencyRange: P_gsm

LapdLinkID: 86

LapdLinkUsage: RSL

ModulationDeltaPower: 0


SpeechCodingRate: FullRate

Tei: 1

TwoAbisHwCapabilityBoolean: Yes

UserLabel: RSL 1




ControlStatus: { }

EGprsHWCapability: Cs1cs2

FrequencyRange: P_gsm

LapdLinkID: 87

LapdLinkUsage: RSL

ModulationDeltaPower: 0


SpeechCodingRate: FullRate

Tei: 2

TwoAbisHwCapabilityBoolean: Yes

UserLabel: RSL 2

END_OF_REPORT

64 / 98 3BK 20900 AAAA PCZZA Ed.08


3.9.17 BTS_restart( bssId, btsId )Input bssId: Integer

btsId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BTS_restart(101,5)DONE

3.9.18 BTS_restartCircuitPack( bssId, btsId, rackId, shelfId, slotId )Input bssId: Integer

btsId: Integer

rackId: Integer

shelfId: Integer

slotId: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd BTS_restartCircuitPack(101,5,1,3,1)DONE

3.9.19 BTS_listSector( bssId, btsId )Input bssId: Integer

btsId: Integer


Example COMMAND_MODE> omcdo -cmd BTS_listSector(101,2)DONE_WITH_INFO

Sector1:1

Sector2:2

END_OF_REPORT

3BK 20900 AAAA PCZZA Ed.08 65 / 98


3.9.20 Sector_display( bssId, btsId, sectorId )Input bssId: Integer

btsId: Integer

sectorId: Integer


Example COMMAND_MODE> omcdo -cmd Sector_display(101,5,1)DONE_WITH_INFO



AvailabilityStatus: { Not installed }

BCCHFrequency: 0

BtsID: 1

CellBarred: No

CellGlobalIdentityCi: 65535

CellGlobalIdentityLaiLac: 65535

CombinerType: Rtc

ControlStatus: { }

EmlAlarmStatus: Cleared

FrequencyRange: P-gsm

GprsCapability: SupportedByHW

NbBaseBandTransceiver: 12

NodeIdentifier: 0

OperationalState: Disabled

TranscodingCapability: Multi rate

UserLabel: Sector1

END_OF_REPORT

3.9.21 OMU_display( bssId, btsId )Input bssId: Integer

btsId: Integer


Example COMMAND_MODE> omcdo -cmd OMU_display(101,5)

66 / 98 3BK 20900 AAAA PCZZA Ed.08


3.9.22 OMU_reset( bssId, btsId )Input bssId: Integer

btsId: Integer


Example COMMAND_MODE> omcdo -cmd OMU_reset(101,5)

3.9.23 OMU_restart( bssId, btsId )Input bssId: Integer

btsId: Integer


Example COMMAND_MODE> omcdo -cmd OMU_restart(101,5)

3BK 20900 AAAA PCZZA Ed.08 67 / 98


3.10 Cell ManagementThis section gives the list of high-level services involved in Cell management.

3.10.1 OMC_listCell()Input None


Example COMMAND_MODE> omcdo -cmd OMC_listCell()DONE_WITH_INFO

216-772-208-05

216-771-208-05

216-101-208-05

216-701-208-05

217-107-208-05

216-702-208-05

END_OF_REPORT

68 / 98 3BK 20900 AAAA PCZZA Ed.08


3.10.2 Cell_display("cellId")Input cellId: String


Example COMMAND_MODE> omcdo -cmd Cell_display("217-107-208-05")DONE_WITH_INFOAdministrativeState: UnlockedAlarmStatus: ClearedAlarmsAcknowledgementStatus: ClearedAlignmentStatus: AlignedAvailabilityStatus: { }BCCHFrequency: 10BSS_Release: B9CellBarred: Cell_not_barredCellGlobalIdentityCi: 107CellGlobalIdentityLaiLac: 217EFR_ENABLED: DisabledEnGprs: DisabledFrequencyRange: p_gsmHR_ENABLED: DisabledHoppingType: NHMfsAdministrativeState: LockedMfsAlarmStatus: ClearedMfsAlarmsAcknowledgementStatus: ClearedMfsAlignmentStatus: AlignedMfsAvailabilityStatus: { }MfsOperationalState: EnabledOperationalState: EnabledPercentageSDCCHavailable: 100PercentageTCHavailable: 100RelatedSecondarySectorCid: NotAvailableCidRnlCellID: 1RnlCellType: SingleRnlSupportingSectorCid: RelatedObjectCidUnknownStatus: NoUserLabel: cell00217_00107END_OF_REPORT

3.10.3 Cell_lock("cellId")Input cellId: String

Output DONE

Example COMMAND_MODE> omcdo -cmd Cell_lock("217-107-208-05")DONE

3BK 20900 AAAA PCZZA Ed.08 69 / 98


3.10.4 Cell_shutdown("cellId", wtc )Input cellId: String

wtc: Integer

Output DONE

Example COMMAND_MODE> omcdo -cmd Cell_shutdown("217-107-208-05", 1)DONE

3.10.5 Cell_unlock("cellId")Input cellId: String

Output DONE

Example COMMAND_MODE> omcdo -cmd Cell_unlock("217-107-208-05")DONE

3.10.6 Cell_bar("cellId")Input cellId: String

Output DONE

Example COMMAND_MODE> omcdo -cmd Cell_bar("217-107-208-05")DONE

3.10.7 Cell_debar("cellId")Input cellId: String

Output DONE

Example COMMAND_MODE> omcdo -cmd Cell_debar("217-107-208-05")DONE

70 / 98 3BK 20900 AAAA PCZZA Ed.08


3.10.8 Cell_resynchronizeGPRS("cellId")Input cellId: String

Output DONE

Example COMMAND_MODE>omcdo -cmd Cell_resynchronizeGPRS("200-55-150-70")DONE

3.10.9 Cell_reinitializeGPRS("cellId")Input cellId: String

Output DONE

Example COMMAND_MODE> omcdo -cmd Cell_reinitializeGPRS("200-55-150-70")DONE

3BK 20900 AAAA PCZZA Ed.08 71 / 98


3.11 MFS ManagementThis section gives the list of high-level services involved in MFS management.

3.11.1 OMC_listMFS()Input None


Example COMMAND_MODE> omcdo -cmd OMC_listMFS()DONE_WITH_INFO

MFS2

MFS1

END_OF_REPORT

3.11.2 OMC_activateMFSs()Input None

Output DONE

Example COMMAND_MODE> omcdo -cmd OMC_activateMFSs()

3.11.3 MFS_resynchronize( mfsId )Input mfsId: Integer


Example COMMAND_MODE>omcdo -cmd MFS_resynchronize(251)DONE_WITH_INFODONEEND_OF_REPORT

3.11.4 MFS_ExportGb ( mfsId, dir )Input mfsId: Integer

dir : Integer (repositoryId parameter of previous function)


Example COMMAND_MODE>omcdo -cmd MFS_ExportGb(251,3)DONE_WITH_INFODONEEND_OF_REPORT

72 / 98 3BK 20900 AAAA PCZZA Ed.08


3.12 PRC ManagementThis section gives the list of high-level services involved in PRC generalmanagement.

3.12.1 OMC_listPRC()Input None


Example COMMAND_MODE> omcdo -cmd OMC_listPRC()DONE_WITH_INFO

prc12

prc17

END_OF_REPORT

3.12.2 OMC_createPRC( prcName, prcDescription, prcAccessRight )Input prcName: String

prcDescription: StringprcAccessRight: Boolean (1->Public, 0->Restricted)

Output DONE

Example COMMAND_MODE> omcdo -cmd OMC_createPRC("prc4","Update of cell X",0)DONE

3.12.3 OMC_createPRCWithCreatorDate ( prcName, prcDescription,prcAccessRight, prcCreator, prcLastModifDate )

Note: This command is used only for migration purpose.

Input prcName: StringprcDescription: StringprcAccessRight: Boolean (1->Public, 0->Restricted)prcCreator: StringprcLastModifDate: String ("YYYYMMDD")

Output DONE

Example COMMAND_MODE> omcdo -cmd OMC_createPRCWithCreatorDate ("prc4","Update of cell X", 0, "userY", "20050630")

DONE

3BK 20900 AAAA PCZZA Ed.08 73 / 98


3.12.4 OMC_deletePRC( prcName )Input prcName: String

Output DONE

Example COMMAND_MODE> omcdo -cmd OMC_deletePRC("prc4")DONE

3.12.5 PRC_display( prcName )Input prcName: String


Example COMMAND_MODE> omcdo -cmd PRC_display("prc21")DONE_WITH_INFO

ActivationMode: MessageMode

NodeIdentifier: 0

ProceduralStatus: { Reporting }

END_OF_REPORT

3.12.6 PRC_exportRadio( prcName, repositoryId )Input prcName: String

repositoryId: Integer (1, 10)

Output DONE

Example COMMAND_MODE> omcdo -cmd PRC_exportRadio("prc7", 1)DONE

74 / 98 3BK 20900 AAAA PCZZA Ed.08


3.12.7 PRC_importRadio( prcName, repositoryId, cgiModeSt )Input prcName: String

repositoryId: Integer (1, 10)cgiModeSt : String (if its value is "cgiMode", it will be considered in the internalprocedure as true; otherwise as false)

Output Nominal case:DONE

Warning case:DONE_WITH_INFO

Example Nominal case:COMMAND_MODE> omcdo -cmd PRC_importRadio("prc", "7", "cgiMode")DONE

Warning case:COMMAND_MODE> omcdo -cmd PRC_importRadio("prc", "2", "cgiMode")DONE_WITH_INFOError Code: rnim-9913Error Description: Warning: File Cell : inconsistent interfacerelease in header file.Error Code: rnim-10228Error Description: Warning: Import/Export - file Cell line 3attributeAGprsTbfCsDl2to1 : Value 0 is out of range for attributeaGprsTbfCsDl2to1.END_OF_REPORT

NB: Error case uses default error format.

3BK 20900 AAAA PCZZA Ed.08 75 / 98


3.12.8 PRC_activate( prcName, activationMode, cellCleanUpMode,triggerMode, withSynchroSt, wtc )

Input prcName: String

activationMode: String taken among ("forcing", "unforcing") value setcellCleanUpMode: String taken among ("withcellscleanup", "withoutcellscleanup")value set

triggerMode: String taken among ("queued", "false") value setwithSyncroSt : String taken among ( "withsynchronisation" and"withoutsynchronisation" ) value setwtc : Integer.



Error case:ERROR

Example Nominal case:COMMAND_MODE> omcdo -cmd PRC_activate("prc3", "forcing","withcellscleanup", "queued", "withoutsynchronisation", 6)DONE

Warning case:The PRC cell is named "cell1", the SC cell is named "c1".COMMAND_MODE> omcdo -cmd PRC_activate("prc2", "forcing","withcellscleanup", "queued", "withsynchronisation", 3)DONE_WITH_INFOObject name: Cell c1(1, 1)Relative Information:WARNING: Risk of intermodulation on the Air interface for the btsto which the cell is mappedWARNING: Risk of HW damage through intermodulation for the bts towhich the cell is mappedObject name: Cell cell1(1, 1)Relative Information:WARNING: Risk of intermodulation on the Air interface for the btsto which the cell is mappedEND_OF_REPORT

Error case:The PRC cell is named "cell1", the SC cell is named "c1".COMMAND_MODE> omcdo -cmd PRC_activate("prc1", "forcing","withcellscleanup", "queued", "withoutsynchronisation", 7)ERRORObject name: Cell c1(1, 1)Relative Information:ERROR: Activated cell becomes unmapped.Object name: Cell cell1(1, 1)Relative Information:ERROR: LAC CI unicity error : a cell with the same LAC CI needs tobe unmapped/deleted to guarantee LAC CI unicity in the domain.END_OF_ERROR_REPORT

76 / 98 3BK 20900 AAAA PCZZA Ed.08


This section gives the list of high-level services involved in Provisioning Cellmanagement.

3.12.9 PRC_listCell( prcName )Input prcName: String


Example COMMAND_MODE> omcdo -cmd PRC_listCell("prc7")DONE_WITH_INFO

800-52-210-70

END_OF_REPORT

3.12.10 PRC_displayCell( prcName, cellId )Input prcName: String

cellId: String


Example COMMAND_MODE> omcdo -cmd PRC_displayCell("jyc","354-45")DONE_WITH_INFO


BSS_Release: B9

CellGlobalIdentityCi: 45

CellGlobalIdentityLaiLac: 354

EFR_ENABLED: Disabled

EnGprs: Enabled

FrequencyRange: p_gsm

HR_ENABLED: Disabled

HoppingType: NH

MfsAdministrativeState: Locked

RelatedSecondarySectorCid: NotAvailableCid

RnlCellId: 0

RnlCellType: Single

RnlSupportingSectorCid: RelatedSectorCid

UserLabel: NieuportEst2

END_OF_REPORT

3BK 20900 AAAA PCZZA Ed.08 77 / 98


3.12.11 PRC_activateCell( prcName, cellId, activationMode )Input prcName: String

cellId: String

activationMode: String taken among ("forcing", "unforcing") value set



Error case:ERROR

Example Nominal case:COMMAND_MODE> omcdo -cmd PRC_activateCell("prc3","1-1","forcing")DONE

Warning case:The PRC cell is named "cell1", the SC cell is named "c1".COMMAND_MODE> omcdo -cmd PRC_activateCell("prc3","1-1","forcing")DONE_WITH_INFOObject name: Cell c1(1, 1)Relative Information:WARNING: Risk of intermodulation on the Air interface for the btsto which the cell is mappedWARNING: Risk of HW damage through intermodulation for the bts towhich the cell is mappedObject name: Cell cell1(1, 1)Relative Information:WARNING: Risk of intermodulation on the Air interface for the btsto which the cell is mappedEND_OF_REPORT

Error case:The PRC cell is named "cell1", the SC cell is named "c1".COMMAND_MODE> omcdo -cmd PRC_activateCell("prc3","1-1","forcing")ERRORObject name: Cell c1(1, 1)Relative Information:ERROR: Activated cell becomes unmapped.Object name: Cell cell1(1, 1)Relative Information:ERROR: LAC CI unicity error : a cell with the same LAC CI needs tobe unmapped/deleted to guarantee LAC CI unicity in the domain.END_OF_ERROR_REPORT

This section gives the list of high-level services involved in Provisioning MFSmanagement.

78 / 98 3BK 20900 AAAA PCZZA Ed.08


3.12.12 PRC_listMFS( prcName )Input prcName: String


Example COMMAND_MODE> omcdo -cmd PRC_listMFS("prc7")DONE_WITH_INFO

MFS2

MFS1

END_OF_REPORT

3.12.13 OMC_openPRC( prcName )Input PrcName: String

Output DONEThis function enables to open a PRC session. It must be used in conjunction withOMC_closePRC service.If a PRC is explicitly opened by the user, using this method, the relative PRC session isregarded as ma

Documents

A1353-RA Command Mode ed08.pdf