1087980 - ECC Source Systems Appearing in BI Folder
2
SAP Note Header Data Symptom Source system connection for an ECC system appears in the BI folder, rather than in SAP folder, as expected. Other Terms Wrong folder,RSA1, RSBASIDOC, RSAP_BIW_DISCONNECT Reason and Prerequisites Transaction RSA1 was inadvertently used on an ECC system , thereby creating a 'Myself' source system entry in RSBASIDOC table Solution This is just a display issue and does not cause any operational issues. Therefore, it need not be corrected, especially if the ECC system in question is used as a BI system as well. If it is absolutely required that the ECC source system appear in the correct folder, perform the following steps. 1. Check that an entry with SRCTYPE 'M' exists in table RSBASIDOC table of ECC source system. 2. Note the values for SLOGSYS and RLOGSYS. It should be same. 3. Run the function module RSAP_BIW_DISCONNECT in the ECC system. NOTE: Never run that function module in a BI system! 4. Enter the following values : I_BIW_LOGSYS <RLOGSYS> as noted in step 2 I_OLTP_LOGSYS <SLOGSYS> as noted in step 2 I_FORCE_DELETE <X> < DO NOT ENTER ANY VALUE IN THE FIELD - RFC target sys !!!!! > 5. Go to RSA1-> Source systems in the BI system connected to the ECC system. 6. Select the ECC source system and select RESTORE in the right click menu. Now the ECC system should appear in the SAP folder. If running RSAP_BIW_DISCONNECT results in an error like OTHER_ERROR, please check if a valid RFC connection exists in transaction sm59. If the myself source system connection cannot be deleted in any case, log a service marketplace message with SAP Support. Validity References 1087980 - ECC Source systems appearing in BI folder Version 6 Validity: 20.03.2008 - active Language English (Master) Released On 20.03.2008 15:49:10 Release Status Released for Customer Component BW-WHM-DST-SRC Source Systems Priority Recommendations / Additional Info Category Help for error analysis Software Component From Rel. To Rel. And Subsequent SAP_APPL 500 500 600 600 SAP_BW 700 700
1087980 - ECC Source Systems Appearing in BI Folder
1087980 - ECC Source Systems Appearing in BI Folder
Citation preview
SAP Note
Header Data
Symptom
Source system connection for an ECC system appears in the BI
folder, rather than in SAP folder, as expected.
Other Terms
Wrong folder,RSA1, RSBASIDOC, RSAP_BIW_DISCONNECT
Reason and Prerequisites
Transaction RSA1 was inadvertently used on an ECC system ,
thereby creating a 'Myself' source system entry in RSBASIDOC
table
Solution
This is just a display issue and does not cause any operational
issues. Therefore, it need not be corrected, especially if the ECC
system in question is used as a BI system as well. If it is
absolutely required that the ECC source system appear in the
correct folder, perform the following steps. 1. Check that an entry
with SRCTYPE 'M' exists in table RSBASIDOC table of ECC source
system. 2. Note the values for SLOGSYS and RLOGSYS. It should be
same. 3. Run the function module RSAP_BIW_DISCONNECT in the ECC
system. NOTE: Never run that function module in a BI system! 4.
Enter the following values : I_BIW_LOGSYS as noted in step 2
I_OLTP_LOGSYS as noted in step 2 I_FORCE_DELETE < DO NOT ENTER
ANY VALUE IN THE FIELD- RFC target sys !!!!! > 5. Go to
RSA1-> Source systems in the BI system connected to the ECC
system. 6. Select the ECC source system and select RESTORE in the
right click menu. Now the ECC system should appear in the SAP
folder. If running RSAP_BIW_DISCONNECT results in an error like
OTHER_ERROR, please check if a valid RFC connection exists in
transaction sm59. If the myself source system connection cannot be
deleted in any case, log a service marketplace message with SAP
Support.
Validity
References
1087980 - ECC Source systems appearing in BI folder
Version 6 Validity: 20.03.2008 - active Language English
(Master)
Released On 20.03.2008 15:49:10 Release Status Released for
Customer Component BW-WHM-DST-SRC Source Systems Priority
Recommendations / Additional Info Category Help for error
analysis
Software Component From Rel. To Rel. And Subsequent
