1 Year – 06 Modules Broad Base Basic Training 6 Months – 03 Modules Advance Module 6 Months – 03 Modules Specialized Module

1 Year – 06 Modules1 Year – 06 Modules

Broad Base Basic Broad Base Basic TrainingTraining

6 Months – 03 Modules6 Months – 03 Modules

Advance ModuleAdvance Module

6 Months – 03 Modules6 Months – 03 Modules

Specialized Specialized ModuleModule

Center of Center of ExcellenceExcellence

Electronics SectorElectronics Sector

Broad Based Broad Based Basic TrainingBasic Training

Advanced Advanced TrainingTraining

Specialized Specialized TrainingTraining

1. Basic Fitting & Soldering

2. Basic Electrical & Electronics

3. Basic Analog Electronics

4. Basic Digital Electronics

5. Basic Measuring Instruments

6. Basic Computers

1. UPS, Inverters & Voltage Stabilizers

2. Communication Systems

3. Embedded Systems & PLC

1. Embedded Systems & PLC

2. POWER ELECRONICS (INVERTER, UPS, STABILIZER & INDUSTRIAL DRIVES

3. Communication Systems

Specialized TrainingSpecialized Training

Module 01Module 01 : : Embedded Systems & PLCEmbedded Systems & PLC

Module 02Module 02 : : POWER ELECRONICS POWER ELECRONICS (INVERTER, UPS, STABILIZER & (INVERTER, UPS, STABILIZER & INDUSTRIAL DRIVESINDUSTRIAL DRIVES

Module 03Module 03 : : Communication SystemsCommunication Systems

Key FeaturesKey Features

Curriculum related to Advance Modules.Curriculum related to Advance Modules.

Course is Designed to Industry needs.Course is Designed to Industry needs.

On Job Training In Industry.On Job Training In Industry.

Training under Apprenticeship Act 1961.Training under Apprenticeship Act 1961.

Training imparted in an industry depend Training imparted in an industry depend upon the facilities available in concerned upon the facilities available in concerned industry.industry.

Certification by D.V.E.T. & Industry.Certification by D.V.E.T. & Industry.

Practical examination is to be taken by the Practical examination is to be taken by the concerned industryconcerned industry

Module 01Module 01

SyllabusSyllabus

WEEK NOWEEK NO SHOPFLOOR TRAININGSHOPFLOOR TRAINING RELATED INSTRUCTIONSRELATED INSTRUCTIONS

1-4

Practical on Basic Electrical & Electronics-1.To measure the voltage current & power of the Series & Parallel Resistor , capacitor & Inductor.2.To study, identification & testing of passive component 3.To study, identification & testing of Active componentB) Basic Analog Electronics1.To study single stage & cascade Amplifier & plot the frequency response.2.To study multivibrators, oscillators & wave shaping ckt.3.To study Variable & Fixed Voltage regulator using 723 & 78xx, 79xx IC.4.To study Temp, displacement, strain gauge microphone, RTD transducers.

Basic Electrical & Electronics-A)Basic Electricity measurement of basic electrical parameters such as voltage, current, power etc.B)Passive components- Identification, testing, use & application of different passive components such as resistors, capacitors, coils etc.C)Active components diodes, transistors, ICs different type packages identification, testing, use & application

Basic Analog Electronics-a.Different configuration of transistor-CB, CE, CC biasing amplifiers, oscillators different circuits applications. Feedback amplifiers, voltage regulators.b.Measuring Instruments such as DVM, DMM, Power supplies, CRO, Function

SyllabusSyllabus


1 to 4 C) Practical on Basic Digital Electronics1.To study & verify truth table of logic Gates2.To study combinational & sequentional ckt.3.To study ADC & DAC.4.To study ALU.

D) Practical on Basic Computers –a.To study Different OS such as Windows 98, Windows 2000, Windows XPb.To study & maintenance of Basic Hardware such as CPU, mother board, different peripherals such as I/P O/P Devices, TFTs, printers such as Dot matrix, Ink jet Laser printers, I/O devices.

1.To study Photo devices such as LDR, Photo cell, Photo transistor, opto-coupler, opto-isolators solar panels & applications.

a.generators, O/P Power meter.b.Special Instrument & transducer & Tacho generators, strain gauge, microphone, power factor meter, speakers, PT-100, RT-100 temp. Transducer.

Basic Digital Electronics1.Basic Gates, Derived Gates, Flip-flop, Registers, counters, multiplexer, Demultiplexer, Adders, subtractors.2.ADC / DAC

Basic Computers –1.Different OS such as Windows 98, Windows 2000, Windows XP2.Basic Hardware such as CPU, mother board, different peripherals, key board, mouse, display device such as monitors, TFTs, printers such as Dot matrix, Ink jet Laser printers, I/O devices.•Photo devices such as LDR, Photo cell, Photo transistor, opto-coupler, opto-isolators solar panels & applications.

SyllabusSyllabus


5-8 1) To study on Microprocessor 8085 based system designing. 2) To assembled, Implementation & view the waveform on CRO.3) Fault finding in designed ckt.

Introduction to Design Of Microprocessor 8085 based system design.

9-12 To study on Microprocessor 8086 based system designing. 2) To assembled, Implementation & view the waveform on CRO.3) Fault finding in designed ckt

Introduction to Design Of Microprocessor 8086 based system design.

13-16 1)To study on Micro controller 8051 based system designing. 2) To assembled, Implementation & view the waveform on CRO.3) Fault finding in designed ckt 4) Practical on

Micro controller 8751, 8032, 8052, 8752, 68HC05, 68HC11, 68HC32 based system design.

Introduction to Design Of Micro controller 8051/8031 based system design.Interfacing of Micro controller to PPI Device, ADC & DAC.

SyllabusSyllabus


17-20 1) To prepare straight & cross Cable.2) To load N/W OS.3) To Load Unix4) To Load Linux5) To configure Network Rights.6) To configure Network Securities

Advanced Computer Networking With Latest OS, Manage Network Right, Networking by using Linux, Unix OS.

21-24 1.To study & configure PLC.2.To connect Different I/O device to PLC.3.Fault finding & maintenance of PLC Based system. 4.To study & configure SCADA & DCS

Introduction to Advanced PLC, Configuration, Architecture, Specification, Programming With PC. Working with Allen Bradley, Fanuc, Siemence, and ABB Etc.Troubleshooting in PLC Based System. Introduction to different Transducer & Signal Conditioning Circuit.Configuration of SCADA & DCS, Troubleshooting.

25-26 Project work Soldering technique, Manuel, Wave soldering, SMD / SMT Technology.SMD Soldering Technique. PCB Design with Latest software/ Tools Available in the market.

RequirementsRequirements

Following facilities should be available in the concerned industry.

8085 based systems.

8086/8088 based systems.

8051 micro controllers based systems.

Computers Latest version with c, c++ with complier.

PIC Programmer Facilities.

Micro controller programmer kit

PLC Based systems.

SCADA

Networking.

Robotics etc.

Module 02Module 02

SyllabusSyllabus


1-4 Practical on Basic Electrical & Electronics-1.To measure the voltage current & power of

the Series & Parallel Resistor , capacitor & Inductor.2.To study, identification & testing of passive

component 3.To study, identification & testing of Active

componentB) Basic Analog Electronics1.To study single stage & cascade Amplifier

& plot the frequency response.2.To study multivibrators, oscillators & wave

shaping ckt.3.To study Variable & Fixed Voltage

regulator using 723 & 78xx, 79xx IC.4.To study Temp, displacement, strain gauge

microphone, RTD transducers.

Basic Electrical & Electronics-a.Basic Electricity measurement of basic electrical parameters such as voltage, current, power etc.b.Passive components- Identification, testing, use & application of different passive components such as resistors, capacitors, coils etc.

Active components diodes, transistors, ICs different type packages identification, testing, use & applicationBasic Analog Electronics-

a.Different configuration of transistor-CB, CE, CC biasing amplifiers, oscillators different circuits applications. Feedback amplifiers, voltage regulators.

SyllabusSyllabus


C) Practical on Basic Digital Electronics1.To study & verify truth table of logic Gates2.To study combinational & sequentional ckt.3.To study ADC & DAC.4.To study ALU.

a.Measuring Instruments such as DVM, DMM, Power supplies, CRO, Function generators, O/P Power meter.

Special Instrument & transducer & Tacho generators, strain guage, microphone, power factor meter, speakers, PT-100, RT-100 temp. Transducer.


•To study Photo devices such as LDR, Photo cell, Photo transistor, opto-coupler, opto-isolators solar panels & applications.


Basic Computers –1.Different OS such as Windows 98, Windows 2000, Windows XP2.Basic Hardware such as CPU, mother board, different peripherals, key board, mouse, display device such as monitors, TFTs, printers such as Dot matrix, Ink jet Laser printers, I/O devices.Photo devices such as LDR, Photo cell, Photo transistor, opto-coupler, opto-isolators solar panels & applications.

SyllabusSyllabus


5-8 1)To study Testing & Installation of single phase Digital / Sine wave Inverters.2) To study Testing & Installation of three phase / Digital / Sine wave Inverters3) Fault finding of single phase Digital / Sine wave Inverters.4) Fault finding of three phase / Digital / Sine wave Inverters.

Inverters Classification of Inverters as a) Single Phase b) Three Phase c) Analogue d) Digital e) Sine Wave f)UsingFET/ MOSFET’sg) Using IGBT’sh)Using Microprocessor, Microcontroller.

Principle of operation, Block diagram, Detailed circuit diagram, circuit diagrams of different brands available in the market, Selection of Inverter as per requirement & Load conditions, Installation of Inverters, fault finding & fault rectification, High power Inverters.

Selection of Batteries, SMF Battery, Tubular Battery, Rating, Back up time, Maintenance & Care, Testing of Battery, Battery Charging Circuits

SyllabusSyllabus


9-12 1) To study, Testing & Installation of single phase Off line UPS.2) To study, Testing & Installation of three phase Off line UPS.3) To study, Testing & Installation of single phase On line UPS.4) To study, Testing & Installation of three phase On line UPS.5) Fault finding of single phase / On line / Off line UPS.6) Fault finding of three phase / On line / Off line UPS.

UPS Classification of UPS a) Single Phase b) Three Phase c) On Line d) Off Line f) Using FET / MOSFET’sg) Using IGBT’sh)Using Microprocessor / Micro controller. Principle of operation, Block diagram, Detailed circuit diagram, circuit diagrams of different brands available in the market, Rating, Selection of UPS as per requirement & Load conditions, Installation of UPS, fault finding & fault rectification, High power UPS.

13-16 1) To study Assembling, testing & Fault finding of Voltage stabilizer of diff. ratings.2) To study Assembling, testing & Fault finding of Servo stabilizer of diff. ratings.

Voltage StabilizersCVT, Spike suppressor, Automatic

Voltage Stabilizers, Servo StabilizersPrinciple of operation, Block diagram,

Detailed circuit diagram, circuit diagrams of different brands available in the market, Rating, fault finding & fault rectification in Stabilizers.

SyllabusSyllabus


17-19 1)To study DC drives (single phase, three phase)2) To study AC drives (single phase, three phase)3) To study speed control of D.C. motor using D.C. Drive4) 3) To study speed control of A.C. motor using A.C. Drive

Industrial Drives AC Drives - Principle of operation,

Block diagram, Detailed circuit diagram, circuit diagram of a Practical AC Drive for Single / Three Phase Induction Motors used in Industries.

DC Drives - Principle of operation, Block diagram, Detailed circuit diagram, circuit diagram of a Practical DC Drive for Series Field, Shunt, Compound DC Motors used in Industries.Starters used for DC Motors, Universal Motor.

Practical Drive using VFD (Variable Frequency Drive), Using PLC (Programmable Logic Controllers.

20-22 1.To study the Microprocessor 8085 based system designing& Testing. 2.To study the Micro controller 8051/8031 based system designing& Testing.

Microprocessors & MicrocontrollersBlock diagram, Architecture,

Addressing Modes, Instruction Set for Microprocessors & Microcontrollers i.e. MP 8085, MP 8086, Micro controller 8031 / 8051, Programming of Microprocessors & Microcontrollers (MP 8085, MP 8086, Micro controller 8031 / 8051), Microprocessors & Micro controller based applications used in the Industries.

SyllabusSyllabus


23-24 1.To study & configure PLC.2.To connect Different I/O device to PLC.3.Fault finding & maintenance of PLC Based system.

Introduction to Advanced PLC, Configuration, Architecture, Specification, Programming With PC. Working with Allen Bradley, Fanuc, Siemence, and ABB Etc.Troubleshooting in PLC Based System. Introduction to different Transducer & Signal Conditioning Circuit.

25-26 Project work Soldering technique, Manual, Wave soldering, SMD / SMT Technology.SMD Soldering Technique.PCB Design with Latest softwaren/ Tools Available in the market.



Different power supplies like fixed, variable & SMPS etc.

Inverters

Choppers

Cycloconverters

Controlled Rectifiers.

UPS systems

Stabilizers

AC/DC Drives

Different Firing ckts for SCR & TRIAC.

Power MOSFET & IGBT.

8051 micro controllers based systems.

Computers Latest version.

Module 03Module 03

SyllabusSyllabus


1-4 Practical on Basic Electrical & Electronics-1.To measure the voltage current & power of the Series & Parallel Resistor , capacitor & Inductor.2.To study, identification & testing of passive component 3.To study, identification & testing of Active componentB) Basic Analog Electronics

A)To study single stage & cascade Amplifier & plot the frequency response.

A)To study multivibrators, oscillators & wave shaping ckt.B)To study Variable & Fixed Voltage regulator using 723 & 78xx, 79xx IC.C)To study Temp, displacement, strain gauge microphone, RTD transducers.

Basic Electrical & Electronics-A)Basic Electricity measurement of basic electrical parameters such as voltage, current, power etc.B)Passive components- Identification, testing, use & application of different passive components such as resistors, capacitors, coils etc.C)Active components diodes, transistors, ICs different type packages identification, testing, use & application

Basic Analog Electronics-a.Different configuration of transistor-CB, CE, CC biasing amplifiers, oscillators different circuits applications. Feedback amplifiers, voltage regulators.b.Measuring Instruments such as DVM, DMM, Power supplies, CRO, Function generators, O/P Power meter

SyllabusSyllabus


C) Practical on Basic Digital Electronics1.To study & verify truth table of logic Gates2.To study combinational & sequentional ckt.3.To study ADC & DAC.4.To study ALU.


1.To study Photo devices such as LDR, Photo cell, Photo transistor, opto-coupler, opto-isolators solar panels & applications.

a..b.Special Instrument & transducer & Tacho generators, strain gauge, microphone, power factor meter, speakers, PT-100, RT-100 temp. Transducer.


Basic Computers –1.Different OS such as Windows 98, Windows 2000, Windows XP2.Basic Hardware such as CPU, mother board, different peripherals, key board, mouse, display device such as monitors, TFTs, printers such as Dot matrix, Ink jet Laser printers, I/O devices.•Photo devices such as LDR, Photo cell, Photo transistor, opto-coupler, opto-isolators solar panels & applications.

SyllabusSyllabus


5-8 1.To study Telegraph & Telephone Instrument .2.Fault finding of telegraph & telephone instrument.3. To study electromechanical switches, and principles of manual and automatic exchanges.

Simple Telegraph and Telephone System: - Telegraph instruments, duplex working tele printers, telephone, electromechanical switches, and principles of manual and automatic exchanges.

9-12 1.To study & fault finding of AM/FM/ transmitter & Receiver2.To study PAM, PDM, PPM, PCM.3.To study FDM & TDM

Modulation Theory and Circuit: - Amplitude modulation, AM-DSB, AM-DSB/SC, AM-SSB and their comparison. Modulating and detector circuit for AM, FM, and phase modulation. Automatic frequency control. Pulse modulation: PAM, PDM, PPM, PCM, delta modulation and circuits. Principles of multiplexing FDM and TDM, frequency generation and synchronization circuits

SyllabusSyllabus


13-16 1.To study & fault finding in demodulator circuit used in PCM system.2.To study Fiber optics communication& its characteristic 3. To study the joining techniques, laying techniques etc.4. To study of LASER & optical transmitter.

Communication System: - Signal to noise ratio in envelope detectors, signal to noise ratio in envelope detectors, signal to noise ratio PCM systems, comparison of modulation system.Optical Communication: - Need of optical communication; Laser & related devices as sources in optical transmitters, modulation techniques- Analog, Digital, Optoelectronics device for receiver- APD’s PCN photodiodes, etc. Low- noise front ends for optical receiver; Free space and fiber- optic communication: Basic of fiber optic- characteristics, measurement, joining techniques, laying techniques etc.

17-20 1.To study Microwave Transmitter 2.To study Microwave Reciver.3.To study GCM Mobile & fault finding4.To study CDMA Mobile & fault finding.5.To study the Broadband / Triband system of communication.6.To study Blue tooth/ infrared communication7.To study Wmax system.

Microwave Links: - Terrestrial line- of - sight communication links, propagation, effects of atmosphere, interference, fading sites and route selection, terminal equipments, including multiplexers, transmitters/receivers. Introduction to troposcatter communication & satellite communication.Mobile Networking :- GSM, CDMA, TDMA, FDMA, SDMA system Broadband system, Triband System Blue tooth, InfraredIntroduction to Wmax System

SyllabusSyllabus


21-24 1)To study satellite communication system.2) To study the working of equipment used in earth station.

Satellite Communication: - Need of Satellite communication, Low-Orbiting and geo- synchronous satellite for communication, choice of frequency bands, current standards. Satellite location in Geo synchronus orbits, current standards, Digital modulation techniques, signal strength calculation, choice of antennas and on board systems, Earth stations antennas, terminal equipments, interfacing with ground network etc. INTELSAT, INSAT, MOLNIYA and other typical systems, satellite broadcasting- basic principles, Remote sensing - basic principles..

25-26 Project work Soldering technique, Manuel, Wave soldering, SMD / SMT Technology.SMD Soldering Technique. PCB Design with Latest software/ Tools Available in the market.



EPABX Systems

Satellite communication system.

Fiber optics (analog/ digital) based systems.

Fiber optics manufacturing process.

Mobile Networking.

Broad band / Triband system.

Mobile service center.

Mobile trainer/ mobile manufacturing.

Computers Latest version.

CRO 100MHZ / 1GHZ

Latest mobile software.

THANK YOU !!THANK YOU !!

Documents

1 Year – 06 Modules Broad Base Basic Training 6 Months – 03 Modules Advance Module 6 Months – 03 Modules Specialized Module