View
214
Download
0
Embed Size (px)
Citation preview
1
Chapter Four
Making Connections
2
Introduction• Connecting peripheral devices to a computer has, in
the past, been a fairly challenging task• Newer interfaces have made this task much easier• Let’s examine the interface between a computer and a
device. This interface occurs primarily at the physical layer
Chapter Four - Making Connections
3
Interface Standards• There are essentially two types of standards
– Official standards, created by standards making organizations such as ITU (International Telecommunications Union), IEEE (Institute for Electrical and Electronics Engineers), EIA (Electronics Industries Association), ISO (International Organization for Standards), and ANSI (American National Standards Institute)
– De-facto standards – protocols created by other groups that are not official standards but because of their widespread use, become “almost” standards
Chapter Four - Making Connections
4
Interface Standards
• There are four possible components to an interface standard:– Electrical component
– Mechanical component
– Functional component
– Procedural component
Chapter Four - Making Connections
5
The Four Components
• The electrical component deals with voltages, line capacitance, and other electrical characteristics
• The mechanical component deals with items such as the connector or plug description.
Chapter Four - Making Connections
6
The Four Components
• The functional component describes the function of each pin or circuit that is used in a particular interface
• The procedural component describes how the particular circuits are used to perform an operation
Chapter Four - Making Connections
7
Two Example Interfaces
• In order to better understand the four components of an interface, let’s examine two popular interface standards– EIA-232F – an older standard originally designed to
connect a modem to a computer
– USB (Universal Serial Bus) – a newer standard that is much more powerful than EIA-232F
Chapter Four - Making Connections
8
RS-232 and EIA-232F
• Originally named RS-232 but has gone through many revisions
• The electrical component is defined by another standard: V.28
• The mechanical component is often defined by ISO 2110, the DB-25 connector. The DB-9 connector is now more common than the DB-25.
Chapter Four - Making Connections
9
Chapter Four - Making Connections
10
RS-232 and EIA-232F
• The functional and procedural components are defined by the V.24 standard
• For example, V.24 defines the function of each of the pins on the DB-9 connector, as shown on the next slide
Chapter Four - Making Connections
11
RS-232 and EIA-232F
Chapter Four - Making Connections
12
RS-232 and EIA-232F
• The next slide shows an example of the procedural dialog that can be used to create a connection between two endpoints
• Note the level of complexity needed to establish a full-duplex connection
Chapter Four - Making Connections
13
Chapter Four - Making Connections
14
Universal Serial Bus (USB)
• The USB interface is a modern standard for interconnecting a wide range of peripheral devices to computers
• Supports plug and play• Can daisychain multiple devices• USB 2.0 can support 480 Mbps (USB 1.0 is only 12
Mbps)
Chapter Four - Making Connections
15
Universal Serial Bus (USB)
• The USB interface defines all four components• The electrical component defines two wires VBUS
and Ground to carry a 5 volt signal, while the D+ and D- wires carry the data and signaling information
• The mechanical component precisely defines the size of four different connectors and uses only four wires (the metal shell counts as one more connector)
Chapter Four - Making Connections
16
Universal Serial Bus (USB)
Chapter Four - Making Connections
17
Universal Serial Bus (USB)
• The functional and procedural components are fairly complex but are based on the polled bus
• The computer takes turns asking each peripheral if it has anything to send
• More on polling near the end of this chapter
Chapter Four - Making Connections
18
Other Types of Connections
• The physical layer is not the only layer involved in a connection
• The data link layer is also involved• Let’s look at the first of these data link layer
connections – the asynchronous connection
Chapter Four - Making Connections
19
Asynchronous Connections
• A type of connection defined at the data link layer• To transmit data from sender to receiver, an asynchronous
connection creates a one-character package called a frame• Added to the front of the frame is a Start bit, while a Stop
bit is added to the end of the frame• An optional parity bit can be added which can be used to
detect errors
Chapter Four - Making Connections
20
Asynchronous Connections
Chapter Four - Making Connections
21
Asynchronous Connections
Chapter Four - Making Connections
22
Asynchronous Connections
• The term asynchronous is misleading here because you must always maintain synchronization between the incoming data stream and the receiver
• Asynchronous connections maintain synchronization by using small frames with a leading start bit
Chapter Four - Making Connections
23
Synchronous Connections
• A second type of connection defined at the data link layer• A synchronous connection creates a large frame that
consists of header and trailer flags, control information, optional address information, error detection code, and data
• A synchronous connection is more elaborate but transfers data in a more efficient manner
Chapter Four - Making Connections
24
Synchronous Connections
Chapter Four - Making Connections
25
Isochronous Connections
• A third type of connection defined at the data link layer used to support real-time applications
• The data must be delivered at just the right speed (real-time) – not too fast and not too slow
• Typically an isochronous connection must allocate resources on both ends to maintain real-time
• USB (and Firewire) can both support isochronous connections
Chapter Four - Making Connections
26
Half Duplex, Full Duplex, and Simplex Connections• A half duplex connection transmits data in both
directions but in only one direction at a time• A full duplex connection transmits data in both
directions and at the same time• A simplex connection can transmit data in only one
direction
Chapter Four - Making Connections
27
Terminal-to-Mainframe Connections
• A point-to-point connection is a direct, unshared connection between a terminal and a mainframe computer
• A multipoint connection is a shared connection between multiple terminals and a mainframe computer
• The mainframe is the primary and the terminals are the secondaries
Chapter Four - Making Connections
28
Terminal-to-Mainframe Connections
Chapter Four - Making Connections
29
Terminal-to-Mainframe Connections• To allow a terminal to transmit data to a mainframe, the
mainframe must poll the terminal• Two basic forms of polling: roll-call polling and hub polling• In roll-call polling, the mainframe polls each terminal in a
round-robin fashion• In hub polling, the mainframe polls the first terminal, and
this terminal passes the poll onto the next terminal
Chapter Four - Making Connections
30
Terminal-to-Mainframe Connections
Chapter Four - Making Connections
• Roll call polling
31
Making Computer Connections In Action
• The back panel of a personal computer has many different types of connectors, or connections:– RS-232 connectors
– USB connectors
– Parallel printer connectors
– Serial port connectors
Chapter Four - Making Connections
32
Making Computer Connections In Action
Chapter Four - Making Connections
33
Making Computer Connections In Action
• 1 and 2 – DIN connectors for keyboard and mouse• 3 – USB connectors• 4 and 6 – DB-9 connectors• 5 – Parallel port connector (Centronics) • 7, 8, and 9 – audio connectors• Will Bluetooth or ??? replace these someday?
Chapter Four - Making Connections
34
Making Computer Connections In Action
• A company wants to transfer files that are typically 700K chars in size
• If an asynchronous connection is used, each character will have a start bit, a stop bit, and maybe a parity bit
• 700,000 chars * 11 bits/char (8 bits data + start + stop + parity) = 7,700,000 bits
Chapter Four - Making Connections
35
Making Computer Connections In Action
• If a synchronous connection is used, assume maximum payload size – 1500 bytes
• To transfer a 700K char file requires 467 1500-character (byte) frames
• Each frame will also contain 1-byte header, 1-byte address, 1-byte control, and 2-byte checksum, thus 5 bytes overhead
Chapter Four - Making Connections
36
Making Computer Connections In Action
• 1500 bytes payload + 5 byte overhead = 1505 byte frames
• 467 frames * 1505 bytes/frame = 716,380 bytes, or 5,731,040 bits
• Significantly less data using synchronous connection
Chapter Four - Making Connections