BELT CONVEYORS HORIZONTAL GRAIN TRANSPORT

Belt conveyors are used to horizontally transport of grains of cereals and maize, legume plants, oleaginous plants, various feed products (meal, middlings, granules and briquettes) and other. Transport of raw material can be continuous at manual or mechanical loading. They are widely used at grain treatment (acceptance, cleaning, drying, storage, etc.), in production plants and mixing plants of feed, large establishments in the food industry.

The belt conveyor is characterised with: • Capacity from 30 to 150 t/h. • Length from 3m to 100m with stroke every 0.5 m.

• Made of galvanised steel sheet from 2 to 4mm. • The whole is screwed with screws of hardness of

8.8. • There are two variants: covered and uncovered. • The possibility to equip the conveyor with a

movable truck with two-way electric distributor (possibility to fill the flat warehouses).

• The are equipped with two-sandwich transporting belt, normal or oil resistant.

• Grain can be transported at an angle with limitation to 30 degrees.

• The belt is connected to each other via the process of curing, so it is not possible to detach on the connection.

• Application of proven drives assures reliable operation of the conveyors.

• We offer different variants of length of the legs under the belt conveyor.

• Depending on capacity of the conveyor, outlet and inlet are designed under the appropriate fittings, such as:

Ø159; Ø219; Ø244.5; Ø324. • The conveyor without a truck can be used in the right-left

option, which means that goods can be discharged at the

end and at the beginning of the device.

Additional equipment of the conveyor: 1. Bearings (feet) under the belt conveyor 2. Movable truck with distributor

3. Additional equipment for the movable truck.

4. Rotations (movement) detector 5. Sensor of belt alignment

LOADING HOOPER

FILLING

STATION

TENSIONING

STATION

GRAIN

OUTLET

CONVEYOR ELEMENT

SCREW CANOPY SUPPORT UNDER BELT

(IN OPERATION MODE TENSIONING CONVEYOR

BELT CONVEYOR RIGHT-LEFT) DRIVEN (LEGS)

ROLLERS

BELT SET STATION N TRANSPORTING DRIVE DRIVE ENGINE

T*00 — 30t/h T400 — 50t/h

T650 — 80t/h T650 —

1301/h T650 — 1501/1

Type

c B C d E F K L-L Filling

dimensi

ons

Electric

power

Belt

speed

Capaci

ty

mm mm mm mm mm mm pc. m mm kW m/s t/h

30t/h 400 540 fi60x167 fi60x434 267 322 1 3.0-70.0 g159 1.5-4.0 1.7 30

50t/h 400 540 fi60x167 fi60x434 267 322 1 3.0-70.0 g219 1.5-4.0 1.7 50

80t/h 650 790 fi60x151 fi60x684 260 320 1 3.0-100.0 244.5 2.2-5.5 1.7 80

130t/h 650 790 fi60x151 fi60x684 260 320 1 3.0-100.0 324 2.2-7.5 1.7 130

150t/h 650 790 fi60x151 fi60x684 260 320 1 3.0-100.0 g324 2.2-7.5 1.7 150 The producer reserves the right to introduce technical changes.

SINGLE-OUTLET OPTION

DOUBLE-OUTLET OPTION (RIGHT-LEFT)

1057 1207

L—L = 1m; 1,5m; 3m; channel x n

L—L + from 1070 to

F

OPTION OF UNCOVERED CONVEYOR WITH A MOVABLE TRUCK WITH DESIGNATED PLACES OF GRAIN DISCHARGE

The covered belt conveyor is characterised with:

• The possibility of applying outside. It is resistant to different climatic conditions. • It takes up little space. • The possibility of discharging goods max. from two discharges (at the beginning and at the end

of the device).

• The possibility of applying at an angle (to 30 degrees).

The uncovered belt conveyor is characterised with: • It must be placed under a canopy. • The conveyor with a movable truck needs free space:

- T400 — 2.0 x 2.0m - T650 — 2.5 x 2.5m

• The possibility to install a movable truck, which allows to: - discharge the bulk material anywhere, however it is not possible to stop at the designated

point (option with electric distributor electric - discharging on two sides of the hall). - discharge the bulk material in the designated location, however it is not possible to discharge

at any other point than the designated (option with discharge to the hooper). • Conducting of the power cable of the truck can be as following:

- conducting on guiding strip (rail), on which the guiding trucks are installed, - conducting on tensioned line, on which clamp hoops with meshes are installed.

• The possibility to set only horizontally.

‘’’ ‘’’

SENSOR OF BELT ALIGNMENT

TENSIONED LINE UNDER TRUCK CABLE GUIDING

INLET

OUTLET

GRAIN OUTLET DISTRIBUTO

R ELECTRIC WITH

TRUCK BELT CONVEYOR

DIRECTION GUIDING

OUTLET SENSOR

OPTION OF UNCOVERED CONVEYOR WITH A MOVABLE TRUCK WITH ANY PLACES OF GRAIN DISCHARGE

- VERSION WITH THE GUIDING TRUCK ON THE GUIDING STRIP

OPTION OF UNCOVERED CONVEYOR WITH A MOVABLE TRUCK WITH ANY PLACES OF

GRAIN DISCHARGE

- VERSION WITH CLAMP HOOPS ON TENSIONED LINE

BELT TRANSPORTING

SUPPOER UNDER CABLE

SUPPORTING

STRUCTURE

UNDER

POWER CABLES

CLAMP HOOPS WITH MESHES

CONVEYOR TRUCK AND

DISTRIBUTO

R

ROTATIONS

FREE SPACE NEEDED TO MOVE THE TRUCK OF THE BELT CONVEYOR WITH POWER CABLE

2000

TRUCK

BELT CONVEYOR

FREE SPACE NEEDED TO MOVE THE TRUCK OF THE BELT CONVEYOR WITH

POWER CABLE

BELT CONVEYOR TRUCK

54

937

0

1190

SUPPORTING BEAMS FOR THE BELT CONVEYOR (EXAMPLE)

Belt conveyor T400

DISCHARGE FROM THE TRUCK OF THE BELT CONVEYOR

SUPPORTING BEAM FOR

THE BELT CONVEYOR (EXAMPLE)

Belt conveyor T650

BELT CONVEYOR

MOVABLE DISPERSER WITH BELT CONVEYORS

The device is used to evenly fill the flat warehouse with the bulk material. It distributes the grain in a designated place. The whole system is based on the conveyor belts, which are supported on special bearing structures, and move on rails on the movable trucks.

Movable disperser with belt conveyors are characterised with: • It must be placed under a canopy. • It consists of 2 uncovered belt conveyors and 1 conveyor with movable truck.

• Discharge of the bulk material is anywhere. • Light device with the structure. • The possibility to set only horizontally.