Upload
iteclearners
View
997
Download
0
Tags:
Embed Size (px)
Citation preview
www.swansea-itec.co.uk
Cabling Technologies -
Infrastructure
• Cat5e / Cat6 / Cat6a – Copper Cabling
• OM1/OM2/OM3/OS1 – Fibre Optic Cabling
• Data Cabinets
• Structured Cabling
• Standards
www.swansea-itec.co.uk
Copper Cabling
• Cat5e
• Cat6
• Cat6a (Augmented)
Speeds and Distances
100MB 1GB 10GB
Cat5e 100m (90m) 100m (90m)
Cat6 100m (90m) 100m (90m) 55m
Cat6a 100m (90m) 100m (90m) 100m (90m)
www.swansea-itec.co.uk
Fibre Optic Cabling
• Introduction
• Fibre Communication Systems
• Fibre Optic Components
• Fibre Optic Cable Construction– Fibre Optic Dimensions
– Types of Fibre Optic Cabling
– What is OM1,OM2,OM3 & OS1 fibre?
– Common Fibre Optic Connectors
www.swansea-itec.co.uk
Introduction
• A fibre optic cable is a thin strand of glass, coated with a protective plastic jacket. A beam of light can be trapped within a fibre, so that the optical cable essentially becomes a pipe that carries light around corners.
• Fibre optic networks can support high data rates.
• Because light is not appreciably affected by electromagnetic fields, optical signals are immune to EMI/RFI/EMP (Electromagnetic Interference/ Radio Frequency Interference/ Electromagnetic Pulse).
• Nearly all long-distance telecommunication lines are fibre optic.
• The primary disadvantage of fibre optic cable is its cost.
www.swansea-itec.co.uk
Fibre Communication Systems
The basic model for a communication system includes a transmitter and
receiver, connected by optical fibre cabling. The Fibre Optic Components
Diagram below illustrates a generic fibre optic communication system.
www.swansea-itec.co.uk
Fibre Optic ComponentsTransmitter (TX)- A transmitter includes the following components:
• Encoder
• Light source
• Connector
The transmitter accepts digital electrical signals from a computer.
A diode converts the digital code into a pattern of light pulses (on and off) that are sent
out to the receiver through the optical fibre.
There are two basic types of light sources for fibre optic systems:
Receiver (RX)- A receiver converts the modulated light pulses back to electrical signals and decodes them.
WARNING: Never look into a fibre
optic cable to see whether light is present.
The infrared laser light used in fibre optic
LANs is invisible; however, it can
permanently damage your eyesight in an
instant.
Light emitting diodes (LEDs)
• use less power and are considerably less expensive than
lasers
• can be used with multimode cable,
• most common light source.
Laser diodes
• used with single-mode fibre for long-distance
transmission.
• Laser light is more powerful
www.swansea-itec.co.uk
Fibre Optic Cable Construction
Optical fibre cable consists of three parts:
• Core - A solid fibre of highly refractive clear glass that serves as the central conduit for light.
• Cladding--A layer of clear glass with a lower index of refraction. When light travelling down the core reaches the boundary between the core and cladding, the change in refractive index causes the light to completely refract or bend back into the core.
• Coating--A reinforced plastic outer jacket that protects the cable from damage.
www.swansea-itec.co.uk
Fibre Optic Dimensions
Fibre optic cable is very thin.
Optical fibres are referred to by their core/cladding diameter measured in
micrometres (µm)
Sizes in perspective
1 metre = 1000 millimetres
1mm = 1000 micrometres
Therefore:
1 µm = micron = 1 metre or 10-6
metres
1,000,000
In comparison, a
human hair is
approximately
50 µm thick
www.swansea-itec.co.uk
Fibre Optic Dimensions
• Fibre optic cable is specified in terms of its core and cladding diameter.
• Each fibre optic core conducts light in one direction only. Therefore, to send and receive, devices are usually connected by two fibre optic strands.
• Fibre cables can also consist of several bundles (4 – 24 fibres).
For example, the most common type of fibre optic
cable for LAN installations is 62.5/125 µm cable, where
62.5 refers to the core diameter and 125 refers to the
cladding diameter.
www.swansea-itec.co.uk
Types of Fibre Optic Cable
Fibre optic cable is available in two types:
• Multimode fibre is wide enough to carry more than one light signal. (Each signal is called a "mode.")
• Single-mode fibre is thin and can carry only one light signal.
www.swansea-itec.co.uk
What is OM1,OM2,OM3 & OS1
fibre?
Fibre Size 100MB Ethernet 1GB Ethernet 10GB Ethernet 40GB Ethernet
OM1 (62.5/125) Up to 550
metres
220 metres 33 metres Not specified
OM2 (50/125) Up to 550
metres
550 metres 82 metres Not specified
OM3(50/125) Up to 550
metres
550 metres 300 metres 100 metres
OM4 (50/125) Up to 550
metres
550 metres 500 metres 150 metres
OS1 (9/125)
(singlemode)
2km – 40km 2km – 40km 2km – 40km Not specified
www.swansea-itec.co.uk
Common Fibre Connections
• SC - Subscriber Connector / Square Connector
• ST - Straight Through / Straight Tip
• MTRJ - Mechanical Transfer Registered Jack
• LC - Local Connector / Little Connector / Lucent Connector
www.swansea-itec.co.uk
Data Cabinets