View
214
Download
0
Category
Preview:
Citation preview
8/2/2019 Termoenergetika Catalogue
1/21
8/2/2019 Termoenergetika Catalogue
2/21
8/2/2019 Termoenergetika Catalogue
3/21
Type OKZ PN6/PN16
Inverted bucket steam traps
We produce the inverted bucket steam traps typeOKZ for nominal pressures PN 6 and PN 16 Thesetraps have automatic air vent on the start-up. Allinternal parts are made of stainless steel and encasedin a cast (cast iron or ductile iron). Dimensionsseparator according to the diameter are given in thetable.
Steam trap size depends from the required capacityand available spressure difference before and afterthe team trap. Maximum capacity depending on thepressure difference before and after the team trap isshown on the included diagram (down).On customer request we can produce variation with ahigher capacity.
DN
DN5
40 0
DN32
"
DN25
R1
DN 0
R /4"
2
3
2
DN15
R1/
"
0,15
0,25 0,
5 1 2 3 4 5 10 160,15
0,2
0,3
0,40,5
1
2
3
4
p [bar]
Q[t/
h]
0,6
0,8
DN15
DN20
DN25
DN32
DN40
L [mm] H [mm]
DN50
R3/4"
R1"
R1/2"
195
225
225
245
275
275
160
160
140
175
180
210
225
275
275
180
210
175
m [kg]
6,9
9,5
10,5
21
23
24,5
8,3
8,7
6
T E E N
L
H
OKZ with flange connection
T E E N
L
H
OKZ with screw connection
Because of retaining of the condensate in thehousing after system stop, at low temperatures thereis danger of freezing and breaking the housing.Because of this they are not recommended foroutdoor installation.In case of cancellation, inverted bucket steam trapsusually remain in the fully open position.
tel: +381 (0)31 715 095fax: +381 (0)31 811808
www.TERMOENERGETIKA.co.rse-mail: office@termoenergetika.rs
ERN GE EO TM IKRAE
T --
ERN GE EO TM IKRAE
T --
Application range for OKZ type steam trapsa, PN16 for flanged connection, according to EN 1092-2
Product: Steam trap, type OKZ
Part Material
Housing EN-GJL-250 (DIN GG-25)Mechanism 1.4301Bucket 1.4301
8/2/2019 Termoenergetika Catalogue
4/21
Type OKZ-VP NP25/NP40
L
T E E N
Steam traps type OKZ-VP are made for nominal pressurePN 25 and PN40. These steam traps have automatic airvent on the start-up. All internal parts are made ofstainless steel, a steel housing is made by welding.Dimensions of this steam traps, according to the diameterare given in the table.For special applications we produce type OKZ-VP withstainless steel housing.
Steam traps type OKZ - VP are designed foroperation at high pressure and the condensatedischarge when the power supply steam is
. These steam traps are not designed fordrainage of the steam line, especially if the steam
line is for superheated steam.
This type of steam traps must be mounted in positionas shown, and the entrance to the separator throughthe lower port.In addition to the basic version separator OKZ-VPwe also produce traps type OKZ-V that has the sameconnection flanges position as the OKZ type ofsteam traps, but is designed for pressures PN 25 andPN 40.
superheated
DN15 310
DN20 310
DN25 310
DN32 330
DN40 350
L [mm]
DN50 350
N32
D5
D
-N
0
5D
DN1
-N25
0,15
0,25 0
5, 1 2 3 4 5 100,15
0,2
0,3
0,40,5
1
2
3
p [bar]
Q[
t/h]
0,6
0,8
20 30
Size choice depends on the required capacity andavailable steam trap pressure difference before andafter the steam trap. Maximum capacity dependingon the pressure difference before and after the steamtrap are given in the diagram.
tel: +381 (0)31 715 095fax: +381 (0)31 811808
www.TERMOENERGETIKA.co.rse-mail: office@termoenergetika.rs
ERN GE EO TM IKRAE
T --
ERN GE EO TM IKRAE
T --
Inverted bucket steam traps
DN
8/2/2019 Termoenergetika Catalogue
5/21
Product: Float ball steam trap, type OKP PN16
Part MaterialHousing EN-GJL-250 (DIN GG-25)Cover EN-GJL-250 (DIN GG-25)Mechanism 1.4301Float ball 1.4301
Type OKP PN6 PN16 PN25
Float ball steam trap
Float ball steam trap, type OKP comes in twovariations: flanged connection from DN15 up toDN50 and with a screwed connection of R1 / 2 ",R3/4`` and R1." These steam traps can be producedfor PN6, PN16 and PN25 nominal pressure.
This type of steam trap, must be fixed in positionshown on drawing (right). OKP type are suppliedwith thermo capsule type TK-M, which allowssteam traps to discharge non-condensing gases. Thisis especially important when starting the installation,when the amount of n gases arelargest.
All internal parts are manufactured odvajca stainlesssteel, witch enables the maximum lifespan. Thehousing is made of cast iron or ductile iron.
on-condensing
Dn15 215
DN20 215
DN25 215
DN32 215
DN40 325
L [mm]
DN50 325
R1/2" 120
R3/4" 120
R1" 120
m [kg]
9,5
10,3
11,3
12
22,5
24
8,5
8,5
8,5
Capacity for OKP type, depending on the availablepressure difference is given in the diagram on thetechnical sheet for type OKP - E.
The cross-section of OKP steam trap
Steam trap OKP with flanged connection
Steam trap OKP with screw connection
In addition to standard version of OKP type (shownin the picture), we have developed a whole range ofsuch separators, but with different position ofconnections to meet our customers requests.
www.TERMOENERGETIKA.co.rse-mail: office@termoenergetika.rs
tel: +381 (0)31 715 095fax: +381 (0)31 811808
ERN GE EO TM IKRAE
T --
ERN GE EO TM IKRAE
T --
Application range for safety valve type OKP, PN16 for flanged connection, according to EN 1092-2
Valve application range
8/2/2019 Termoenergetika Catalogue
6/21
Product: Steam tr ap, type OKP-E
Part Material
Housing EN-GJL-250 (DIN GG-25)Cover EN-GJL-250 (DIN GG-25)Mechanism 1.4301
Float ball 1.4301
Type OKP-E DN 40 and DN 50
Float ball steam trap
Type OKP - E which is modified steam trap of OKPseries. OKP-E has a servo mechanism to open steamtrap. This mechanism allows the steam trap to has alarger diameter of the valve openings and thus littlepressure drop. Due to this OKP-E has a largecapacity even at at low pressure differences.
The steam trap type OKP-E is designed for largeconsumers and eventually to consumers who workwith low steam pressure, and have relatively high
power. This type of steam trap comes only indimensions of DN40 and higner. Depending on therequired capacity at the request of the users OKP-Ecan modified (the mechanism) to allow even agreater capacity of the steam trap, then declared inthe attached (down) diagram.
Steam trap type OKP-E can be applicated for flushvessel supply, in such application OKP-E regulatesthe level of condensate in the vessel.
Steam trap type OKP - E has a same built-inmeasures as OKP type.
K
0
OP-E
DN4
-DN5
0
5
OKPD
N40-
DN 0
Ni
OKPD
N25-
D32
R1"
i
OKPD
N15
-N
15R1/2"
-R3/4"
D
0,15 ,20
5 ,05 1 2 3 4 5 10 16
0,15
0,2
0,3
0,40,5
1
2
3
4
6
p [bar]
Q[
t/h]
0,6
0,8
Mechanism of the OKP - E type
tel: +381 (0)31 715 095fax: +381 (0)31 811808
www.TERMOENERGETIKA.co.rse-mail: office@termoenergetika.rs
ERN GE EO TM IKRAE
T --
ERN GE EO TM IKRAE
T --
Steam trap application range
Application range for steam trap, type OKP-E PN16 for flanged connection, according to EN 1092-2
Intersection of the OKP - E type
8/2/2019 Termoenergetika Catalogue
7/21
Product: Thermostatic steam trap, type TKL
Part Material
Housing EN-GJL-250 (DIN GG-25)Cover EN-GJL-250 (DIN GG-25)
Thermo capsule 1.4301
L 150 160
TKL DN15 TKL DN20
L
R1/2" - R3/4"
125
Mass:DN 15 - 3,5 kgDN 20 - 4,0 kg
R1/2" - 2,4 kgR3/4" - 2,3 kg
Steam traps type TKL come with the threadedconnection of R1 / 2 ", R3 / 4" R1 "and the flangeconnection from DN15 up to DN50.Steam traps type TKL DN15 and DN20 and typeTKL R 1/2 "and 3/4" have one typeTK (picture below).Steam trap housing is made of cast iron or cast steel.It can be disassembled, in order to enable quick andeasy replacement of thermal capsule. Replacecapsule is possible without removing the steam trapfrom the pipeline, and the time required for capsule
replacement does not exceed 15 minutes.Replacement of the capsules are practicallycompleted overhaul of separators.These steam traps can be mounted in any position,depending on the capsule filling may dischargecondensate undercooled up to 40 C. Standard fillingof the capsule enables discharge up to 10C subcooling.
thermal capsule
condensate
Type TKL DN 15 - DN 20
Thermostatic steam traps
N15D
i/ "
-"
D-
N20 R
12 R
1
01,5
0,25 0
5, 1 2 3 4 5 10 160,15
0,2
0,3
0,40,5
1
p [bar]
Q[
t/h]
0,6
0,8
tel: +381 (0)31 715 095fax: +381 (0)31 811808
ERN GE EO TM IKRAE
T --
www.TERMOENERGETIKA.co.rse-mail: office@termoenergetika.rs
Installationmeasures
ERN GE EO TM IKRAE
T --
Valve application range
Application range for steam trap type TKL, DN15,DN20 PN16 for flanged connection, according to EN 1092-2
8/2/2019 Termoenergetika Catalogue
8/21
Type TKL - M / TKL - MG
Thermostatic steam trap
Thermostatic steam traps type TKL - M and TKL- MG have screw connection of R1 / 2 ", R3 / 4"and R1 ", they have nominal pressure PN16.
At the costumer request, TKL-M can come withstainer integrated within of the housing of thesteam trap.
Replaceable thermostatic element is inside thesteam trap, it is a thermostatic capsule type TK-
M.This steam trap discharges the condensate withsubcooling from 10 to 20 C. In this way it isexploited the heat of condensate and it isdecreased the amount of flash steam. Typicallythe steam traps type TKL - M and TKL - MGused in heating systems, cooking food duplicatesin hospitals and hotels, the smaller diameterpipelines steam drainage etc.
Steam trap has a folding housing, so it allowsreplacement of thermostatic capsule. Thissignificantly increases life time of these steamtraps.
At the costumer request , we can deliver this typeof steam trap to release condensate with 40 C ofsubcooling.
T E E N
TKL - M
A
B
TKL - MG
T E E N
A
B
Housing material is cast iron (EN-GJL-250).Internal parts are made of stainless steel(1.4301). Seal of the housing is achievedKlingerit, and sealing the thermostatic capsule
with Teflon.Cover
Thermostatic capsule TK-M
Sealing
Housing
Sealing
Cover
tel: +381 (0)31 715 095fax: +381 (0)31 811808
ERN GE EO TM IKRAE
T --
www.TERMOENERGETIKA.co.rse-mail: office@termoenergetika.rs
ERN GE EO TM IKRAE
T --
8/2/2019 Termoenergetika Catalogue
9/21
Type TKZ
Thermostatic steam traps
Thermostatic steam traps type TKZ is made entirelyfrom stainless steel. It's sealed in welded housing.
Compact design and small built in measures provideeasy installation. We produce them for a nominalpressure PN25 PN16, with screw connection R1/2 ",R3 / 4" R1 ".
In addition to the standard version we have version oftype TKZ with eccentrically offset connectors, as
well as version with both internal threadedconnection.
The TKZ type has installed thermal capsule, typeTK. Depending on the requirements we can provideundercooling of condensate from 5 to 30 C.
TKZ type steam trap can be installed in any position.In the case of installation as shown on picture, on thesystem stop, condensate can leak out of steam trap sothere is no danger of freezing. In the case of freezing
up to -5C there is no fracture of internal parts or thecasing, so it is suitable for drainage and steamconsumers who may be exposed to lowtemperatures.
L
p Ki TZ
T
01,5
0,25 0
5, 1 2 3 4 5 10 160,15
0,2
0,3
0,40,5
1
p [bar]
Q[
t/h]
0,6
0,8
TKZ's housing is not retractable so it is not foreseenthe possibility of replacing capsule.
This steam traps have the lowest price compared toother steam traps and a very long life time. Warrantyfor this type is two years.
Separator type is usually applied TKZ for the
installation of steam heating, steam for outdoordrainage, ancillary heating. It also applies toconsumers in small drainage prehrabenoj, chemical,petrochemical industry, etc.. They are good and theaccompanying heating fuel oil and heating fuel oiltanks.Odvaja tip TKZ se najee primenjuje zainstalacije parnog grejanja, za spoljnju drenauparovoda, pratee grejanje. Takoe se primenjuje zadrenau manjih potroaa u prehrabenoj, hemijskoj,
tel: +381 (0)31 715 095fax: +381 (0)31 811808
ERN GE EO TM IKRAE
T --
www.TERMOENERGETIKA.co.rse-mail: office@termoenergetika.rs
ERN GE EO TM IKRAE
T --
8/2/2019 Termoenergetika Catalogue
10/21
Thermodynamic steam trap
Type TDK
We have developed a new series of thermodynamictraps type TDK, with the thermodynamic capsule.
tel: +381 (0)31 715 095fax: +381 (0)31 811808
ERN GE EO TM IKRAE
T --
www.TERMOENERGETIKA.co.rse-mail: office@termoenergetika.rs
Optionaly, upon customer request in the housing ofthe steam trap strainer can be monted.
Housing of the steam trap is the thermal chamberthat provides a relatively uniform value oftemperature inside the housing, regardless ofexternal conditions. This results in optimumtemperature for traps. Inside the housing is thereplaceable thermodynamic capsule type TD.
Housing and internal parts of this steam trap aremade of stainless steel.
TDK series are produced with screw connection insizes: R 1 / 2 `, R 3 / 4 ` and ` R1
In the following table are given values of
capacity for steam traps type TDK, related to theworking pressure.
8/2/2019 Termoenergetika Catalogue
11/21
Type BPZ
Thermostatic bimetallic steam traps
Steam trap type BPZ is thermostatic steam ttrapwith bimetallic plates. This bimetallic steam trapcomes with screw connection, sizes: R1 / 2 ", R3 /4 and R1,with the nominal pressure PN16 orPN25.
BPZ type is made of stainless steel, so ithas a long life of impeccable work. It comes in
welded housing. This steam trap has asmall mounting dimensions and light weight. It is
suitable for steam line drain and the drain ofconsumers who are not affected with undercoolingof the condensate.
This steam trap can be installed in any position. Ifinstalled vertically, after the syistem stop,condensate can freely drain from the installationand steam trap housing, so there is no danger offrost. The model BPZ, will not suffer breakage ofhousing or internal parts due to freezing, if it isexposed to the temperatures down to -5?
At the customer it is possible to adjust forother mounting positions and size of connections.
entirely
compact
C.
request
95
tel: +381 (0)31 715 095fax: +381 (0)31 811808
16www.TERMOENERGETIKA.co.rse-mail: office@termoenergetika.rs
ERN GE EO TM IKRAE
T --
Like the all thermostatic steam traps, drain
with undercooling from 5 to 30 ,depending on customer requirements. BPZ typesteam trap is recommended for drainage of steamline with superheated steam and drainage of
consumers . It is suitable forinstallation outside of buildings because it allowscondensate to flow out of the housing after theplants stopping / pausing(do not keep the condensatein the housing).
BPZ
condensate ?C
superheated steam
In the following table (left) are given values ofcapacity for steam traps type BPZ, related to theworking pressure.
8/2/2019 Termoenergetika Catalogue
12/21
Direct action regulation valve
Type RVD
RVD is a direct action pressure regulator. It isdesigned for controlling steam, oil, air and water
. We produce it with the screw connectionsof R1 / 2 " up to R6 / 4" and for nominal pressures ofPN 16 to PN 25
All internal valve parts are made of stainless steel(1.4301). Membranes are a combination of stainlesssteel and Teflon. Housing made of cast iron, ductileiron or cast steel.All direct action valves regulated pressure o deviates
from the set pressure. Deviation is depending on thecurrent flow. Valves with direct action also have asmaller opening force so there are produced only forthe smaller sizes (DN). If it is needed a bigger DN, itis recommend to use pilot operated valve, likeRVSU type valve witch have servo device. ValveRVD has the lowest price so you should always beapplied when technological requirements allow it.
RVD type can be mounted in any position. Also itallows the adjust of the regulated pressure without a
system stop. On flow rise, regulated pressure tends todrop. The maximum deviation from the presetpressure is up to 10% of regulated pressure.
RVD valve is designed to control pressure exceeding2.5 bar. For pressure regulation below 2.5 bar, it canbe used modified version of RVD valve labeled asRVD - N.
RVD valves are used for pressure ratio (at the inletand outlet) four to one (p1 / p2
8/2/2019 Termoenergetika Catalogue
13/21
Product: Regulation valve, type RVSU PN16
Part Material
1. Pilot valve cover EN-GJL-250 (DIN GG-25)2. Pilot valve housing EN-GJL-250 (DIN GG-25)3. Valve housing EN-GJL-250 (DIN GG-25)4. Membrane(diaphragm) housing EN-GJL-250 (DIN GG-25)5. Spring DIN EN 172236. Membrane(diaphragm) PTFE, 1.43017. Impulse lines EN Cu-DLP8. Pilot valve 1.4301
9. Seat 1.430110. Disc (plug unit) 1.430111. Spring handler 1.430112. Spindle (Stem)` 1.4301
Regulation valve
Type RVSU
Regulation valve type RVSU is a mechanical servopressure regulator. This valve is designed to control
steam pressure or air. It consists of two parts, themain valve and pilot valves. The pilot valve, uses themembrane located at the bottom of the valve controlsthe main valve, so this system is called - servo valve.Steam pressure regulation with the valve typeRVSU is very precise. Practically, the steam pressurebehind the valve does not depend on the current flowof steam or pressure applied to the flow of 0 to 100%of maximum flow. The advantage of servo regulationis virtually unlimited ratio of input and outputpressure.
All inside parts of valves are made of stainless steel,membranes are a combination of stainless steel andteflon(PTFE), and the casing is made of cast iron orsteel.Capacity depends on the valve inlet pressure and theregulated pressure. For the calculation of capacityuse is Kv values obtained by measuring the valve.These coefficients are given in table below-right.These coefficients are given in table below, andbelow the table are given the equation for flowcalculation.Valve type RVSU found is widely
applied in many industries. It has a long work lifetime, low cost and relatively simple maintenanceprocedures.
RVSU
DN15
DN20
DN25
DN32
DN40
DN50
DN65
DN80
DN100
DN125
DN150
L [mm]
130
150
165
180
200
230
290
310
350
360
400
G [kg]
12,5
13,7
17,5
19,5
26,5
31,5
32,2
34,7
68
80
117
Kvs [m /h]
3
4
5
7
10
17
33
42
67
130
177
3
L
p1 p2
For saturated steam:
p2> W=Kvs 15,88 p(p1+p2)p12
p2< W=Kvs 13,76 p1p12
p1, p2, p [bar] W [kg/h]
tel: +381 (0)31 715 095fax: +381 (0)31 811808
These valves exploitation life time is from fourup to seven years. After this it is necessary to do
maintenance. Maintenance is low costcomparing to the price of new valve and increasesthe exploitation time of the valve for several moreyears.This valve also has version with solenoid valvemounted on the pulse line. This enables theremote turning on/off with control of the steampressure.
ERN GE EO TM IKRAE
T --
www.TERMOENERGETIKA.co.rse-mail: office@termoenergetika.rs
ERN GE EO TM IKRAE
T --
Valve application range
Application range for control valve type RVSU PN16 for flanged connection, according to EN 1092-2
8/2/2019 Termoenergetika Catalogue
14/21
Product: Temperature contro l valve, type RT
Part Material
1. Probe housing EN Cu-DLP2. Valve housing EN-GJL-250 (DIN GG-25)
3.Membrane(diaphragm)housing
EN-GJL-250 (DIN GG-25)
4. Spring DIN EN 172235. Membrane (diaphragm) PTFE, 1.43016. Impulse lines EN Cu-DLP7. Pilot valve 1.43018. Seat 1.43019. Disc (plug unit) 1.430110. Spindle (Stem) 1.4301
Temperature control valve
Type RT
RT type valve is a mechanical, pilot operated,temperature regulator. Mounts to the side of thesteam or condensate, and regulates the temperatureof heated fluid. It has a servo device, the pilot valveis temperature control valve type T2.
Modified version of RT valve is used to controlcooling. This valve is placed on the side of thecooling water. This modified valve is labeled as typeRT-R.
RT
DN15
DN20
DN25
DN32
DN40
DN50
DN65
DN80
DN100
DN125
DN150
L [mm]
130
150
165
180
200
230
290
310
350
360
400
G [kg]
12,5
13,7
17,5
19,5
26,5
31,5
32,2
34,7
68
80
117
Kvs [m /h]
3
4
5
7
10
17
33
42
67
130
177
3
These valves comes for nominal pressure PN16 andPN25 and nominal diametar up to DN 150. Allinternal parts are made of stainless steel (1.4301)
and membrane are made of combination of stainlesssteel and Teflon or copper and stainless steel. Thecasing is made of cast iron, ductile iron or cast steel.
RT is supplied with a length of 1500 mm capillaries,where the user's request can be delivered withgreater capillary length.
Weights and valve Kv value is given in the attachedtable.
p1, p2, p [bar] W [kg/h]
For saturated steam:
p2> W=Kvs 15,88 p(p1+p2)p12
p2< W=Kvs 13,76 p1p12
For water:
W=Kvs 1000 p
tel: +381 (0)31 715 095fax: +381 (0)31 811808
This valve regulates the temperature of heatedfluid in a very narrow limits, with the largesterror to 5 C, with good adjustment can reducethe error below 3 C.
ERN GE EO TM IKRAE
T --
www.TERMOENERGETIKA.co.rse-mail: office@termoenergetika.rs
ERN GE EO TM IKRAE
T --
320
R1/2"
R3/4"
360
Valve application range
Application range for control valve type RT PN16 for flanged connection, according to EN 1092-2
8/2/2019 Termoenergetika Catalogue
15/21
DN 25 32 40 50 65 80 100 125 150Dnozle [mm] 19 25 42 48 56 63 79 100 125
Pnozle [mm 2 ] 283,39 490,63 1384,74 1808,64 2461,76 3115,67 4899,19 7850 12265,62
Flanges: DIN EN 1092-1/2
EN 4126-1 Implemented
Product: Safety valve, type VSO
Part Material
1. Protective cover EN-GJL-250 (DIN GG-25)2. Screw for spring adjusting 1.43013. Nut for the setting fixation 1.43014. Spring handler-upper 1.43015. Spring DIN EN 17223
6. Central pillar 1.43017. Spring housing EN-GJL-250 (DIN GG-25)8. Lever for manually relieve EN-GJL-250 (DIN GG-25)9. Spring handler-lower 1.430110. Spindle guiding 1.430111. Valve housing EN-GJL-250 (DIN GG-25)12. Spindle (Stem) 1.430113. Disc (plug unit) 1.430114. Seat 1.4301
Safety valve for steam
Type VSO
A
B
C
Safety valve with spring type VSO is designed to workwith saturated steam. This valve has a valve seat and plug
unit, made of stainless steel. Valves plug unit at therequest of the customer may have a ring of viton, or teflon.Depending on the open pressure and the named diametershown table (down right) gives steam discharge capacity .For this table assumes that the pressure behind the valveis approximately equal to atmospheric.
tel: +381 (0)31 715 095fax: +381 (0)31 811808
ERN GE EO TM IKRAE
T --
www.TERMOENERGETIKA.co.rse-mail: office@termoenergetika.rs
ERN GE EO TM IKRAE
T --
A
DN25
DN32
DN40
DN50
DN65
DN80
DN100
B
DN40
DN50
DN65
DN80
DN100
DN125
DN150
C
R1/2"
R1/2"
R1/2"
R1/2"
R1/2"
R1/2"
R1/2"
Application range for safety valve type VSO, PN16 for flanged connection, according to EN 1092-2
Set pressure[bar]
Name diameter - DN
DN25 DN32 DN40 DN50 DN65 DN80 DN100
1
1,5
2
2,5
3
4
5
6
7
8
9
10
12
14
228
302
371431
490
612
738
856
976
1095
1213
1331
1567
1800
363
480
590684
781
983
1173
1363
1551
1740
1928
2120
2491
2851
592
782
19601116
1270
1600
1910
2219
2526
2831
3140
3446
4055
4661
914
1209
14851724
1964
2475
2953
3430
3906
4380
4853
5326
6296
7204
1557
2057
25282935
3341
4210
5026
5836
6645
7453
8258
9060
10665
12257
2367
3129
38454465
5084
6403
7645
8878
10107
11337
112561
13782
16225
18644
3660
4836
59446901
7858
9899
11817
13723
15623
17524
19416
21303
25078
28818
Capacity [kg/h]
* f low rate is 90% of the declared when thepressure exceeded set pressure by 10%
Valve application range
A - Steam inletB - Steam outletC - Valves drainage for condensate
8/2/2019 Termoenergetika Catalogue
16/21
Product: Safety valv, type VSO-G
Part Material
Screw for spring adjusting 1.4301Nut for the setting fixation 1.4301Spring handler-upper 1.4301Spring DIN EN 17223Central pillar 1.4301Spring housing EN-GJL-250 (DIN GG-25)Handle for manually relieve 1.4301Spring handler-lower 1.4301Spindle guiding 1.4301Valve housing EN-GJL-250 (DIN GG-25)Spindle (Stem) 1.4301
Disc (plug unit) 1.4301Seat 1.4301EN 4126-1 implemented
Spring operated safety valve for steam and water
Type VSO - G
Steam capacity [kg/h]
Setpressure
[bar]
Named diameter
R1/2" R3/4" R1" R3/2"
1
2
3
4
5
6
7
8
9
10
12
14
34,25,05,86,57,17,88,28,79,2
10,210,9
5,57,4
9,010,411,612,713,814,715,616,5
18,019,4
8,111,013,415,517,219,020222324
2729
12,516,92124262931343638
4145
Water capacity [m /h]
3
G1R1/2"
R3/4"
R1"
R3/2"
G2R1"
R5/4"
R3/2"
R2"
Spring operated safety valve type VSO - G is
designed to work with saturated steam or water. Thisvalve has a seat and plug made of stainless steel.Disc-plug unit at the request of the customer mayhave a ring of viton, or teflon. Depending on the setpressure and the named diameter in the lower tablesare given capacity discharge for steam and water. Forthis tables it is assumed that the pressure behind thevalve is approximately equal to atmospheric.
tel: +381 (0)31 715 095fax: +381 (0)31 811808
ERN GE EO TM IKRAE
T --
www.termoenergetika.co.rse-mail: office@termoenergetika.rs
ERN GE EO TM IKRAE
T --
* fl ow rate is 90% of the declared when the pressure exceededset pressure by 10%
* fl ow rate is 90% of the declared when the pressure exceededset pressure by 10%
R1/2" R3/4" R1" R3/2"
1
1,5
2
2,5
3
4
5
6
78
9
10
7086102119136171207242
277312347381
126153182212243306369431
493555618680
197241286333383480578675
7748719691066
3223944675416267859451105
1264142415841744
Named diameterSetpressure
[bar]
8/2/2019 Termoenergetika Catalogue
17/21
Product: Spring operated safety valve, type VSV
Element name Material
1. Protective cover EN-GJL-250 (DIN GG-25)2. Screw for spring adjusting 1.43013. Nut for the setting fixation 1.43014. Spring handler-upper 1.43015. Spring DIN EN 172236. Central pillar 1.4301
7. Spring housing EN-GJL-250 (DIN GG-25)8. Spring handler-lower 1.43019. Spindle guiding 1.430110. Spindle (Stem) 1.430111. Valve housing EN-GJL-250 (DIN GG-25)12. Disc (plug unit) 1.430113. Seat 1.4301Flanges: DIN EN 1092-2EN 4126-1 implemented
Spring operated safety valve - for water
Type VSV
Spring operated safety valve type VSV is designed to
work with cold and hot water. In the table below aregiven work areas for the predefined set of springs.
tel: +381 (0)31 715 095fax: +381 (0)31 811808
ERN GE EO TM IKRAE
T --
www.TERMOENERGETIKA.co.rse-mail: office@termoenergetika.rs
Optimal relief, on valve activation, ofinstallation is achieved with usage of differentsprings for different pressures are correctlyinstalled relief activating safety valves.Valve type VSV has seat made of stainless steel.
The plug unit can be stainless steel, viton andteflon (PTFE).
ERN GE EO TM IKRAE
T --
Spring No.Spring
workingarea
1. 0.2-0.5
2. 0.5-1
3. 1-1.5
4. 1.5-2.5
5. 2.5-4.5
6. 4.5-8.5
7. 8.5-19
Application range for safety valve type VSV, PN16 for flanged connection, according to EN 1092-2
Valve application range
8/2/2019 Termoenergetika Catalogue
18/21
Weight operated safety valve - for steam
Type VST
A
B
C
DN25 DN32 DN40 DN50 DN65 DN80 DN100
11,5
2
2,5
3
4
5
6
7
8
910
12
14
254336
412479
545687
820952
10851217
134814791742
2001
404534
656761
8681093
13041515
17241934
214323562768
3168
658869
10671240
14121778
21232466
28073149
348938294506
5179
10161344
16511916
21832750
32823812
43404867
539359186966
8005
17302286
28093262
37134678
55856485
73848282
91761006711851
13619
26313477
42734962
56497115
84959865
1123112597
139571531418028
20716
40675374
66057668
873210999
1313115248
1735919472
215742367127865
32021
Weight operated safety valve type VST is designed
to work with saturated steam. This valve has a valveseat and disc are made of stainless steel. Disc (plugunit) at the request of the customer may have a ringof viton, or teflon. Depending on the pressure and thenamed diameter table (down) shows nominal steam
capacity. For this table it is assumed thatthe pressure behind the valve is approximately equalto atmospheric.
discharge
A
DN25
DN32
DN40
DN50
DN65
DN80
DN100
B
DN40
DN50
DN65
DN80
DN100
DN120
DN150
C
R1/2"
R1/2"
R1/2"
R1/2"
R1/2"
R1/2"
R1/2"
tel: +381 (0)31 715 095fax: +381 (0)31 811808
ERN GE EO TM IKRAE
T --
www.TERMOENERGETIKA.co.rse-mail: office@termoenergetika.rs
ERN GE EO TM IKRAE
T --
* fl ow rate is 90% of the declared when the pressure exceeded set pressure by 10%
Name diameter - DNSet pressure
[bar]
Capacity [kg/h]
A - Steam inletB - Steam outletC - Valves drainage for condensate
Application range for safety valve type VST, PN16 for flanged connection, according to EN 1092-2
Valve application range
8/2/2019 Termoenergetika Catalogue
19/21
Water supply program
Type RP10 - 1
PV
S1
S2PS
The picture (right) is shown the basic version of apressure regulator type RP10 - 1 On the basis of thisversion was developed full range of control valvesfor water.
The main valve is controlled by a pilot valve (PV).Through ball valve S1 and choke valve PS waterflows to above side of the main valves memebrane-diaphragm. If the pilot valve is closed then thediaphragm will push the plug unit-disc of the mainvalve in the closed position. If the pilot valve is fully
open, then the liquid from the space above themembrane will flow out in the pipeline behind themain valve.
At that moment pressure above the diaphragm islower then the pressure ahead of the main valve, themembrane will move up and change the position ofthe valve to open. In this way, the pilot valve controlsthe main valve.
The degree of valve lift depends on the pressurebehind the valve (pressure regulated), which is leadunder the diaphragm pilot valve that balances withthe spring over memebrane. Compaction of springscan be changed on the spot. Speed of opening andclosing of the main valve is set by the choke valve PS.
RP series valves are made for nominal pressure PN6,PN10, PN16 and PN25.
They come in flanged or screw connection:
Screw connection: from R1" to R2"Flange connection: from DN50 to DN300
Maximum fluid temperature is 120C
tel: +381 (0)31 715 095fax: +381 (0)31 811808
This valve can be lead into a fully open or fullyclosed position with ball valves S1 and S2. If thevalve S1 is closed, the valve is lead into a fully openposition, if the valve S2 is closed, the valve has beentranslated into a fully closed position.
All inside parts are made of stainless material(stainless steel and Teflon) and housing is made of acast steel or cast iron.
The pilot valve is made of stainless steel.
ERN GE EO TM IKRAE
T --
www.TERMOENERGETIKA.co.rse-mail: office@termoenergetika.rs
ERN GE EO TM IKRAE
T --
RP series - water pressure control valves
8/2/2019 Termoenergetika Catalogue
20/21
8/2/2019 Termoenergetika Catalogue
21/21
Recommended