Upload
thorne-derrick
View
201
Download
12
Embed Size (px)
Citation preview
31PPE - CPE / Arc Flash Protection
PPE - CPE
Fire-retardant clothing in case of exposure to an electric arc, confirming
to IEC 61482-2 and the regulation NFPA 70E.
PROTECTION AGAINST ARC FLASH
The following are used to determine the proper equipment for protecting against anelectric arc:• The maximum fault current value.• The phase/ground rated voltage at the site of the risk.• The distance between the source of the arc and the reception surface.• The AC cycle number and the mono or three-phase circuit type.• The location where the arc is produced (confined space).
After recording these parameters, we can estimate the level of risk and determinethe proper protective clothing and PPE to use: 12 to 100 cal/cm2 or class 1 or 2.
For more information, please contact our technical department.
The "Arc Flash" phenomenon.An electric arc follows a short circuit. It produces nearly instant effects with seriousconsequences without proper protection.
Arc Flash Protectionthe solution for complete electric arc protection
- The arc's main manifestation is its thermal effect. The heat energy released, which is proportional to the voltage, intensity, and fault length, can be considerable(19.000°C), melting the metal and charring the insulation.
- Blast effect, caused by the very rapid release of energy in a limited volume of air (similar to an explosion).
- Light effect with high ultraviolet and infrared radiation.- Ionisation effect that can trigger an arc on nearby active sections.
When electric arc danger exists, heat-resistant clothing must be worn.The arc's characteristics are given by:• The resistance value of the free arc, expressed in cal/cm2 according to NFPA 70 E,
ASTM standards, and IEC 61482-1-1.or• The protection class (1 or 2) with a constrained arc according to IEC 61482-1-2.
mmDimensions kg Weight
32PPE - CPE / Arc Flash protection
Arc Flash protection
Nomex III ® Undergloves100% Nomex III® fire-resistant and heat-resistant undergloves. Protects the hands against heat of up to 100°C. Ideal protection for "arc flash" equipment.
High performance synthetic Nomex III ® fibre.
Reference
CG-37
Characteristics
One size 32Includes 5 pairs
EN 407EN 420
Fire protection.
g
33PPE - CPE / Arc Flash equipment
PPE - CPE
Arc Flash equipment
"Arc flash" face shield kit(12 cal/cm2)
1.5
MO-187
MO-182/1-B
M-87413
Reference KIT-ARC-01
1 Face shield with chin cup 12 cal/cm2, absorbs> 99.9% of harmful UV radiation,
70% light transmission, tested to ASTM F 2178specifications
1 ABS helmet electrically insulated EN397, EN 50365, ANSI Z89.1 20kV.
1 carrying bag for face shield and helmet
NFPA 70E
ATPV 20 Cal/cm2
IEC 61482-1-1IEC 61482-1-2 Classe 2
ElectricianABS helmet.
Large fieldof view.
Chin protection
Anti UV and polycarbonate1.5 mm thickness.
"Arc flash" Helmet (20 cal/cm2)The only one all integrated helmet with "arc flash"faceshield on the market.
NFPA 70E
CharacteristicsReference
MO-180-ARC Integrated helmet with "arc flash" Faceshield 1.2
"Arc flash" coverall double zipperProtects against the thermal hazards of an electric arc. Easy to put on.
CharacteristicsReference
MV-105(*) Ultra soft 1.4
Composition
RetractableFaceshield highvisibility& UV Protection.According toNFPA 70EASTM F 2178IEC 61482-2IEC 61482-1-1IEC 61482-1-2class 2GS-ET 29
Mechanical & Electrical Protection helmetEN 397EN 50365
Double zipper along the entire length.
Light, compact and flexible protection in Arc rated fabricASTM F1959ASTM F1506
IEC 61482-2
NFPA 70E
(*) to complete by size M, L ou XL. Other sizes on request.
kg
kg
kg
Total length g WeightPackaging
34PPE - CPE / Arc Flash equipment
Arc Flash equipment
(*) Reference to be completed by the size M, L or XL.Size S to 3 XL on request.
*1 For reference KIT-ARC-12-C-(*).*2 For reference KIT-ARC-12-C-(*).*3 For reference KIT-ARC-12-J-(*).
Blue jacket 3/4with 12 cal/cm2.
Protectivehood12 cal/cm2.
Safety glasses.
Coverall 12 cal/cm2.
Reference Characteristics
KIT-ARC-12-C-(*) *1
KIT-ARC-12-J-(*) *2
KIT-ARC-12-JP-(*) *3
Coverall
Long hooded jacket
Short jacket withouthood + pants
Capacity cal/cm2
12 cal/cm2
12 cal/cm2
12 cal/cm2
4.2
3
4.4
IEC 61482-2 NFPA 70E
Made of ultra soft ®
confortable and light.
"Arc flash" jacket and protective coverall kits (12 cal/cm2)
Made of Indura ultra soft ®
confortable and light.
Carrying bagfor the kit.
kg
Face shield on electrician helmet
MO-187
MO-182/1-B
MO-11000
MO-134
—
M-87413
M-87295
1 Face shield with chin cup 12 cal/cm2, absorbs> 99.9% of harmful UV radiation, tested to
ASTM F2178 specifications
1ABS helmet electrically insulated EN397, EN 50365, ANSI Z89.1, 20kV.
1 safety glasses EN 166/EN 170
1 arc flash protective hood (12 cal/cm2), only with coverall and blue short jacket.
1 protective coverall 12 cal/cm2 *1 , ASTM F1506 and NFPA 70E Standards or1 arc flash protective jacket 12 cal/cm2, ASTM F1506 and NFPA 70E Standards.
1 carrying bag for face shield and helmet.
1 all kit carrying bag.
Composition of KITS
35PPE - CPE / Arc Flash equipment
Arc Flash equipment
PPE - CPE
MO-182/1-B
MO-11000
M-87295
KIT-ARC-25-B-(*) *1
KIT-ARC-40-B-(*) *2
KIT-ARC-65-B-(*) *3
KIT-ARC-100-B-(*) *4
—
Carrying bagfor the kit.
Arc Flash protectivehood with face shield, 40 cal/cm2. Electrician helmet.
Arc Flash Dungarees, 40 cal/cm2.
Safety glasses.
Arc Flash Jacket, 40 cal/cm2.
IEC 61482-2 NFPA 70E
"Arc flash" protective kits (25, 40, 65 or 100 cal/cm2)
Reference Capacity cal/cm2
25
40
65
100
6
6.9
8
8
KAKI
GREY
CAMEL
CAMEL
Color
Composition of KITS
M-881968 *1
M-881961 *2
M-881976 *3
M-881979 *4
1 arc flash protective hood with an integrated
face shield 25 *1, 40 *2, 65 *3 or 100 *4 cal/cm2,
ASTM F2178 and NFPA 70E Standards
1 ABS helmet electrically insulated EN397, EN 50365, ANSI Z89.1 20kV.
—
1 safety glasses EN 166/EN 170
1 arc flash protective bib overall 25 *1,
40 *2, 65 *3 or 100 *4 cal/cm2, ASTM F1506
and NFPA 70E Standards
1 arc flash protective coat 25 *1, 40 *2,
65 *3 or 100 *4 cal/cm2, ASTM F1506 and
NFPA 70E Standards
1 all kit carrying bag
KIT-ARC-40-B-(*)KIT-ARC-25-B-(*) KIT-ARC-65/100-B-(*)
kg
(*) Reference to be completed by the size M, L or XL.Size S to 3 XL on request.
*1 For reference KIT-ARC-25-B-(*).
*2 For reference KIT-ARC-40-B-(*).
*3 For reference KIT-ARC-65-B-(*).
*4 For reference KIT-ARC-100-B-(*).
kg Weight
Knitted glove, 15 gauge, made oftexturized polyamide, blackcolour, black nitrilfoam coating onpalm and fingertips.
CG-951
36PPE - CPE / Workwear and other protections
2 flattened breastspockets closed by injected zips every plastic part hidden.
Workwear and other protections
Electrician coverallCoverall without metallic part, avoiding any flash hazards. 100% cotton.
CG-951 ManutentionActivities: Assembly, fitting, construction, maintenance and all building construction work.CG-952 Mechanical protection (cutting) Activities: Packaging, cutting, handling sharp and/or oily objects, stamping, automotive, aerospace, railway work, sharpening, all building and outdoor work.
Tape measure pocket on right back leg.
Neck jumper
Gusset back.
Front closed by injected zipevery plasticpart hidden.
2 flattened thighspockets.
Tape measurepocket onright back leg.
Reference
(*) Reference to be completed by the size,ex : MV-104/02.
36/38
40/42
44/46
48/50
52/54
56/59
60/62
64/66
MV-104/ (*)
Size
76/84
85/92
92/100
101/108
109/116
117/124
125/132
133/140
Chest size
00
01
02
03
04
05
06
07
Size forRef. (*)
Other Protection
Work Gloves
Reference
115
115
(*) Reference to be completed by the size of A, B, C or D.
A = 8
B = 9
C = 10
D = 11
One size
C = 10
CG-96-(*)
CG-97-C
Size
EN 388EN 420
CG-96-C
CG-97-C
American style gloves with very soft and flexible full bloom leather allowing full finger movement.
"Docker" style gloveswith very soft full bloomleather allowing full finger movement.
Semirigid red fabric top with elastic on the back.
3122
4544
4121
3122
g
Reference
Feeding fat and / or humid environment: installation,
adjustment, drawing, constructionand maintenance, wiring
and building work.
(*) Reference to be completed by the size of 07, 08, 09 or 10.
7 to 10
CG-951-(*)
CG-952-(*)
Size Use
Tightening elastic on theback of the hand.
Knitted glove, 13 gauge, made of cut resistant fibers, elasticated knitwrist,grey, with a black nonslip nitrilfoam coating on palm and fingertips.
CG-952