10G XFP Transceivers

XFP is short for 10 Gigabit Small Form Factor Pluggable. It is a standard for serial 10 Gbps

fiber optic transceivers in high-speed computer network and telecommunication links that

use optical fiber. XFP was defined by an industry group in 2002, along with its interface to

other electrical components which is called XFI.

XFP transceivers are hot-swappable and protocol-independent, fully compliant to the

following standards: 10G Ethernet (10GbE), 10G Fibre Channel (FC), SONET OC-192, SDH

STM-64 and OTN G.709, supporting bit rate from 9.95G through 11.3G. They are used in

datacom and telecom optical links and offer a smaller footprint and lower power

consumption than other 10 Gbps transponders.

XFP transceivers typically operate at near-infrared wavelengths of 850 nm, 1310 nm or 1550

nm. They can operate over a single wavelength or use DWDM techniques. They include

digital diagnostics that provide management that were added to the SFF-8472 standard.

The XFP modules use an LC fiber connector type to achieve high density.

XFP transceivers are available with a variety types, allowing users to select the appropriate

transceiver for each link to provide the required optical reach over the available optical fiber

type (MMF or SMF). XFPs are commonly available in several different categories:

SR– 850 nm, for a maximum of 300 m

LR– 1310 nm, for distances up to 10 km

ER – 1550 nm, for distances up to 40 km

ZR– 1550 nm, for distances up to 80 km

Youtube Vedio

The XFP packaging was smaller than the XENPAK form-factor which had been published

earlier (by almost a year). Some vendors supported both, or the XENPAK follow-ons called

XPAK and X2.

FiberStore has been providing high performance and cost-effective G XFP Transceiver

solutions for serial optical data communications applications specified for signal rates of 8.5

Gbps to 11.3 Gbps. It is fully compliant to XFP MSA Rev 4.5. The XFP modules are designed

for single-mode fiber and operates at a nominal wavelength of 850/1310/1550 nm

including DWDM XFP, CWDM XFP, BiDi XFP, 10G XFP and compatible Cisco XFP, Juniper XFP,

Brocade XFP, ect.. We guarantee our XFP transceivers to work in your system and all of our

XFP comes with a lifetime advance replacement warranty.

Compatible XFP

All our XFP transceivers are 100% compatible with major brands and backed by a lifetime

warranty. Meanwhile, we can customize transceivers to fit your specific requirements.

Contact us if you can’t find the item which you need. FiberStore has a large selection of

Compatible XFP modules in stock and can ship the XFP modules to you within 24 hours.

Compatible Brands: Cisco, Juniper, Brocade, Dell, 3Com, Foundry, Extreme, Alcatel-Lucent, Allied

Telesis, D-Link, Enterasys, H3C, Huawei, Adtran, Agilent-Avago, Aruba Networks, Ciena, Delta, F5

Networks, Finisar, Force10, Fortinet, Fujitsu, HP, IBM, IMC Networks, JDS Uniphase, Marconi,

Netgear, Nortel Networks, Palo Alto Networks, PicoLight, Rad, Redback, SMC, Sun, Telco,

Transition Networks, etc..

G XFP

8G XFP transceiver is designed for serial optical data communications such as 8G Fibre

Channel. The 8G XFP optical transceiver is XFP MSA Complaint and support digital

diagnostics functions. A serial EEPROM in the transceiver allows the user to access

transceiver digital diagnostic monitoring and configuration data via the 2-wire XFP

Management Interface.

Features:

Compliance to Fibre Channel 800-M5-SN-l, 800-M5E-SN-l, 800-M6-SN-l at 8.5 Gbps

Laser Class 1M compliant

Compliant with SFP MSA and SFF-8472 with duplex LC receptacle

Compatible with RoHS

VCSEL at 850 nm, 1310 nm and 1550 nm

Average Output Power: -7.3 to -1 dBm

Receiver Sensitivity: -11.1 dBm

Transmission distance up to 300 m with OM3 MMF; 82 m with OM2 MMF; 33 m with OM1

MMF

Fully compliant to XFP MSA Rev.4.5

CWDM XFP

CWDM XFP transceiver series is designed for single-mode fiber serial optical data

communications such as 10GbE 10GBASE-ER/EW/ZR and 10G FC 1200-SM-LL-L. There are

18 center wavelengths available from 1270 nm to 1610 nm, with each step 20 nm. Our

CWDM XFP modules are designed for single mode fiber and operate at a nominal

wavelength of CWDM wavelength. They are available in various distances from 10Km up to

80Km. Maximum optical budget is 23dB.

Features:

Average Output Power: -5 to 0 dBm

Receiver Sensitivity: -15 dBm

High Quality with ISO9001, TUV, CE, FCC, UL and RoHS certificates

Condition: Factory New

Supports 9.95 Gbps to 11.1 Gbps

Hot-Pluggable XFP footprint

18-Wavelength CWDM DFB Transmitter from 1270 nm to 1610 nm, with step 20 nm

Hot Pluggable

Operating Case Temperature Standard: 0°C to +70°C

Duplex LC connector

Temperature-Stabilized DWDM Rated EML Transmitte

Build-in digital diagnostic functions

DWDM XFP

DWDM XFP transceivers comply with the current XFP MSA specification. They support

DWDM 10Gbps SONET/SDH, DWDM 10GbE and 10G FC applications. Digital diagnostics

functions are available via a 2-wire serial interface, as specified in the XFP MSA. Our DWDM

XFP modules are 100% compatible with original products, and they can transmit and receive

optical data over single fiber for link length of 40km up to 80km transmission on

single-mode fiber.

Features:

Supports 9.95 Gbps to 11.1 Gbps

High Quality with ISO9001, TUV, CE, FCC, UL and RoHS certificates

Auxiliary 1 Monitoring Laser Temperature

Auxiliary 2 Monitoring 5V Supply

Temperature-Stabilized DWDM EML Transmitter

Maximum Link Length of 40km/80km

Hot-Pluggable XFP+ Footprint

Temperature-Stabilized DWDM Rated EML Transmitter

100GHz ITU Grid, C Band

Duplex LC Connector

Built-in Digital Diagnostic Functions

Power Dissipation < 3.5 W

Average Output Power: -1 to 4 dBm

Receiver Sensitivity: -15 dBm

Operating Case Temperature: Standard: 0°C to 70°C

BIDI XFP

10G BiDi XFP series transceivers are designed for bi-directional 10G serial optical data

communications such as IEEE 802.3ae 10GBASE-BX by using 1330(1270nm) transmitter and

1270(1330) nm receiver. The transceiver consists of two sections: The transmitter section

uses a multiple quantum well 1330(1270) nm DFB laser and is a class 1 laser compliant

according to International Safety Standard IEC 60825. The receiver section uses an

integrated 1270(1330) nm detector preamplifier (IDP) mounted in an optical header and a

limit. FiberStore provide compatible BiDi XFP modules in various distances from 10Km up to

60Km transmission on single-mode fiber.

Features:

Supports 9.95 Gbps to 10.5 Gbps

Power budget 9dB at least

1270nm/1330nm DFB Transmitter/Receiver

Average Output Power: -5 to 0 dBm

Receiver Sensitivity: -14 dBm

LC Connector

+3.3V power supply only

Power dissipation < 2 W

Built-in digital diagnostic functions

Case temperature range: Standard: 0 to +70℃

Complaint with XFP MSA

Complaint with IEEE 802.3ae 10GBASE-LR/LW

Complaint with 10GFC 1200-SM-LL-L

Multirate XFP

Multirate 8G/10G XFP transceiver is designed for serial optical data communications such as

8G FC and 10G/11.1G speed rates. Abailable in TDM XFP, CWDM XFP, BIDI XFP, DWDM XFP.

Customized model design is available on request.

Features:

Up to 11.1 Gbps Data Link

Only Required +3.3 V Power Supply

Compatible with RoHS

VCSEL at 850 nm, 1310 nm and 1550 nm

Average Output Power: -7.3 to -1 dBm

Receiver Sensitivity: -11.1 dBm

Built-in Digital Diagnostic Function

XFP Loopback

XFP loopbacks provide a method for port operation testing in board, hub, system and

applications. It supports various 10G application standards and is capable of achieving up to

10Gbps data transfer rate. The dual integrated LED indicator light ensures the loopback is

properly seated, powered and performance status. XFP Loopbacks are hot swappable,

constructed of die cast for EMI performance. They are compliant with the industry standard

XFP MSA.

Features:

Support 9.95 Gbps to 10.7 Gbps data rate

Operating temperature -40°C to +85°C

Front dual LED status indicator

3W power consumption, 2.5W/2W/1.5W Customer optional

No reference clock required

Built-in digital diagnostic functions and memory organized to meet XFP MSA Ver4.5

Electrical loopback and with CDR version optional

Suitable for chamber testing

Automatically shutdown & self-protection

Source: http://www.fiberopticshare.com/