Upload
tapon-chakraborti
View
290
Download
6
Embed Size (px)
DESCRIPTION
Plasticity, Theory of Plasticity ,Creep in concrete ,Creep, Stiffness ,Elasticity ,Plasticity ,Euler-Bernoulli beam equation, Buckling, Ductility VS Malleability, Ductile Materials, Brittle Materials ,Modulus of Elasticity, Plastic Strain, Tensile Strength, Yield Strength, Ultimate Strength, Solid mechanics or Mechanics of solids, Strength of Materials, Types of forces, Normal forces, Fatigue , Resilience, Unit of Resilience, Modulus of rigidity , Modulus of Resilience, Modulus of Toughness Poisson’s Ratio.
Citation preview
Plasticity, Theory of Plasticity ,Creep in concrete ,Creep, Stiffness ,Elasticity
,Plasticity ,Euler-Bernoulli beam equation, Buckling, Ductility VS Malleability,
Ductile Materials, Brittle Materials ,Modulus of Elasticity, Plastic Strain, Tensile
Strength, Yield Strength, Ultimate Strength, Solid mechanics or Mechanics of solids,
Strength of Materials, Types of forces, Normal forces, Fatigue , Resilience, Unit of
Resilience, Modulus of rigidity , Modulus of Resilience, Modulus of Toughness
Poisson’s Ratio.
ENGINEERING MATERIALS RELATED
TERMS
1
ENGINEERING
MATERIALS
RELATED TERMS
CIVIL ENGINEERING TERMS.
It is very important to know the terms described in this book .These
terms are mainly on the “CIVIL “& based on the characteristics of
different types of materials used in construction process.
TAPON CHAKRABARTI
DEDICATING
THE
STUDENTS
OF CIVIL
ENGINEERIN
G, ALL OVER
THE WORLD.
2
Engineering Materials related Terms
PLASTICITY is concerned with the mechanics of materials deformed beyond their elastic limit.
A strong knowledge of plasticity is essential for engineers dealing with a wide range of engineering
problems, such as those encountered in the forming of metals, the design of pressure vessels, the
mechanics of impact, civil and structural engineering, as well as the understanding of fatigue and the
economical design of structures.
THEORY OF PLASTICITY is the most comprehensive reference on the subject as well as the
most up to date -- no other significant Plasticity reference has been published recently, making this of
great interest to academics and professionals. This new edition presents extensive new material on the
use of computational methods, plus coverage of important developments in cyclic plasticity and soil
plasticity, and is accompanied by a fully worked solutions manual.
* A complete plasticity reference for graduate students, researchers and practicing engineers; no other
book offers such an up to date or comprehensive reference on this key continuum mechanics subject
* Updates with new material on computational analysis and applications, new end of chapter exercises
and a worked solutions manual
* Plasticity is a key subject in all mechanical engineering disciplines, as well as in manufacturing
engineering and civil engineering.
CREEP IN CONCRETE is defined as: deformation of structure under sustained load. Basically,
long term pressure or stress on concrete can make it change shape. This deformation usually occurs in
the direction the force is being applied. Like a concrete column getting more compressed, or a beam
bending. Creep does not necessarily cause concrete to fail or break apart. Creep is factored in when
concrete structures are designed
Factors Affecting Creep
1. Aggregate
2. Mix Proportions
3. Age of concrete
1. Influence of Aggregate
Aggregate undergoes very little creep. It is really the paste which is responsible for the creep.
However, the aggregate influences the creep of concrete through a restraining effect on the magnitude
of creep. The paste which is creeping under load is restrained by aggregate which do not creep. The
stronger the aggregate the more is the restraining effect and hence the less is the magnitude of creep.
3
The modulus of elasticity of aggregate is one of the important factors influencing creep. It can be
easily imagined that the higher the modulus of elasticity the less is the creep. Light weight aggregate
shows substantially higher creep than normal weight aggregate.
2. Influence of Mix Proportions:
The amount of paste content and its quality is one of the most important factors influencing creep. A
poorer paste structure undergoes higher creep. Therefore, it can be said that creep increases with
increase in water/cement ratio. In other words, it can also be said that creep is inversely proportional
to the strength of concrete. Broadly speaking, all other factors which are affecting the water/cement
ratio are also affecting the creep.
3. Influence of Age:
Age at which a concrete member is loaded will have a predominant effect on the magnitude of creep.
This can be easily understood from the fact that the quality of gel improves with time. Such gel creeps
less, whereas a young gel under load being not so stronger creeps more. What is said above is not a
very accurate statement because of the fact that the moisture content of the concrete being different at
different age also influences the magnitude of creep.
EFFECTS OF CREEP ON CONCRETE AND REINFORCED CONCRETE:
In reinforced concrete beams, creep increases the deflection with time and may be a
critical consideration in design.
In eccentrically loaded columns, creep increases the deflection and can load to buckling.
In case of statically indeterminate structures and column and beam junctions creep may relieve the
stress concentration induced by shrinkage, temperatures changes or movement of support. Creep
property of concrete will be useful in all concrete structures to reduce the internal stresses due to
non-uniform load or restrained shrinkage.
In mass concrete structures such as dams, on account of differential temperature conditions at the
interior and surface, creep is harmful and by itself may be a cause of cracking in the interior of
dams. Therefore, all precautions and steps must be taken to see that increase in temperature does
not take place in the interior of mass concrete structure.
Loss of prestress due to creep of concrete in prestressed concrete structure.
CREEP:
Deformation that occurs from stresses over long period of time, typically materials exposed to
constant heat will be susceptible to creep.
DEFORMATION:
Change in shape (i.e. length, width, diameter, etc.) of a material due to an applied force.
4
Also fatigue is another form of deformation. Fatigue describes deformation which is caused by
repetitive stress.
STIFFNESS
Stiffness depends upon material properties and geometry. The stiffness of a structural element of a
given material is the product of the material's Young's modulus and the element's second moment of
area. Stiffness is measured in force per unit length (newtons per millimetre or N/mm), and is
equivalent to the 'force constant' in Hooke's Law.
The deflection of a structure under loading is dependent on its stiffness. The dynamic response of a
structure to dynamic loads (the natural frequency of a structure) is also dependent on its stiffness.
In a structure made up of multiple structural elements where the surface distributing the forces to the
elements is rigid, the elements will carry loads in proportion to their relative stiffness - the stiffer an
element, the more load it will attract. This means that load/stiffness ratio, which is deflection, remains
same in two connected (jointed) elements. In a structure where the surface distributing the forces to
the elements is flexible (like a wood framed structure), the elements will carry loads in proportion to
their relative tributary areas.
A structure is considered to fail the chosen serviceability criteria if it is insufficiently stiff to have
acceptably small deflection or dynamic response under loading.
The inverse of stiffness is flexibility.
ELASTICITY
Much engineering design is based on the assumption that materials behave elastically. For most
materials this assumption is incorrect, but empirical evidence has shown that design using this
assumption can be safe. Materials that are elastic obey Hooke's Law, and plasticity does not occur.
For systems that obey Hooke's Law, the extension produced is directly proportional to the load:
Where
x is the distance that the spring has been stretched or compressed away from the equilibrium position,
which is the position where the spring would naturally come to rest [usually in meters],
F is the restoring force exerted by the material [usually in newtons], and
k is the force constant (or spring constant). This is the stiffness of the spring. The constant has units
of force per unit length (usually in newtons per meter)
PLASTICITY
Some design is based on the assumption that materials will behave plastically. A plastic material is
one which does not obey Hooke's Law, and therefore deformation is not proportional to the applied
5
load. Plastic materials are ductile materials. Plasticity theory can be used for some reinforced concrete
structures assuming they are under reinforced, meaning that the steel reinforcement fails before the
concrete does.
Plasticity theory states that the point at which a structure collapses (reaches yield) lies between an
upper and a lower bound on the load, defined as follows:
If, for a given external load, it is possible to find a distribution of moments that satisfies
equilibrium requirements, with the moment not exceeding the yield moment at any location, and
if the boundary conditions are satisfied, then the given load is a lower bound on the collapse load.
If, for a small increment of displacement the internal work done by the structure, assuming that
the moment at every plastic hinge is equal to the yield moment and that the boundary conditions
are satisfied, is equal to the external work done by the given load for that same small increment of
displacement, then that load is an upper bound on the collapse load.
If the correct collapse load is found, the two methods will give the same result for the collapse load.
Plasticity theory depends upon a correct understanding of when yield will occur. A number of
different models for stress distribution and approximations to the yield surface of plastic materials
exist:
EULER-BERNOULLI BEAM EQUATION
The Euler-Bernoulli beam equation defines the behavior of a beam element (see below). It is based on
five assumptions:
(1) Continuum mechanics is valid for a bending beam
(2) the stress at a cross section varies linearly in the direction of bending, and is zero at the centroid of
every cross section.
(3) The bending moment at a particular cross section varies linearly with the second derivative of the
deflected shape at that location.
(4) The beam is composed of an isotropic material
(5) the applied load is orthogonal to the beam's neutral axis and acts in a unique plane.
A simplified version of Euler-Bernoulli beam equation is:
Here is the deflection and is a load per unit length. is the elastic modulus and is
the second moment of area, the product of these giving the stiffness of the beam.
This equation is very common in engineering practice: it describes the deflection of a uniform, static
beam.
Successive derivatives of u have important meaning:
6
Is the deflection.
Is the slope of the beam.
Is the bending moment in the beam.
Is the shear force in the beam.
A bending moment manifests itself as a tension and a compression force, acting as a couple in a beam.
The stresses caused by these forces can be represented by:
Where is the stress, is the bending moment, is the distance from the neutral axis of the beam
to the point under consideration and is the second moment of area. Often the equation is simplified
to the moment divided by the section modulus (S), which is I/y. This equation allows a structural
engineer to assess the stress in a structural element when subjected to a bending moment.
BUCKLING
A column under a centric axial load exhibiting the characteristic deformation of buckling.
When subjected to compressive forces it is possible for structural elements to deform significantly due
to the destabilizing effect of that load. The effect can be initiated or exacerbated by possible
inaccuracies in manufacture or construction.
The Euler buckling formula defines the axial compression force which will cause a strut (or column)
to fail in buckling.
Where
= maximum or critical force (vertical load on column),
= modulus of elasticity,
= area moment of inertia, or second moment of area
= unsupported length of column,
7
= column effective length factor, whose value depends on the conditions of end support of the
column, as follows.
For both ends pinned (hinged, free to rotate), = 1.0.
For both ends fixed, = 0.50.
For one end fixed and the other end pinned, 0.70.
For one end fixed and the other end free to move laterally, = 2.0.
This value is sometimes expressed for design purposes as a critical buckling stress.
Where
= maximum or critical stress
= the least radius of gyration of the cross section
Other forms of buckling include lateral torsional buckling, where the compression flange of a beam in
bending will buckle, and buckling of plate elements in plate girders due to compression in the plane of
the plate.
DUCTILITY VS MALLEABILITY
Ductility is a solid material's ability to deform under tensile stress; this is often characterized by the
material's ability to be stretched into a wire.
Malleability, a similar property, is a material's ability to deform under compressive stress; this is often
characterized by the material's ability to form a thin sheet by hammering or rolling.
Both of these mechanical properties are aspects of plasticity, the extent to which a solid material can
be plastic-ally deformed without fracture.
8
9
10
11
DUCTILE MATERIALS:
Ductile materials will withstand large strains before the specimen ruptures.
Ductile materials often have relatively small Young’s moduli and ultimate stresses.
Ductile materials exhibit large strains and yielding before they fail.
Steel and aluminum usually fall in the class of Ductile Materials
12
BRITTLE MATERIALS:
Brittle materials fracture at much lower strains.
Brittle materials often have relatively large Young’s moduli and ultimate stresses.
Brittle materials fail suddenly and without much warning.
Glass and cast iron fall in the class of Brittle Materials.
MODULUS OF ELASTICITY:
In solid mechanics, Young’s modulus (E) is a measure of the stiffness of a material. It is defined
as the ratio of stress over strain in the region in which Hooke’s Law is obeyed for the material.
Units: Young’s modulus is the ratio of stress, which has units of pressure to strain, which is
dimensionless; therefore Young’s modulus itself has units of pressure.
PROPORTIONAL LIMIT:
The point up to which the stress and strain are linearly related is called the proportional limit.
ULTIMATE STRESS:
The largest stress in the stress strain curve is called the ultimate stress.
RUPTURE STRESS:
The stress at the point of rupture is called the fracture or rupture stress
ELASTIC REGION:
The region of the stress-strain curve in which the material returns to the undeformed state when
applied forces are removed is called the elastic region.
PLASTIC REGION:
The region in which the material deforms permanently is called the plastic region.
YIELD POINT:
The point demarcating the elastic from the plastic region is called the yield point. The stress at yield
point is called the yield stress.
PLASTIC STRAIN:
The permanent strain when stresses are zero is called the plastic strain.
The off-set yield stress is a stress that would produce a plastic strain corresponding to the specified off-
set strain. A material that can undergo large plastic deformation before fracture is called a ductile
material. A material that exhibits little or no plastic deformation at failure is called a brittle material.
13
Hardness is the resistance to indentation. The raising of the yield point with increasing strain is
called strain hardening.
Necking Phenomenon:
The sudden decrease in the area of cross-section after ultimate stress is called necking.
TENSILE STRENGTH
Tensile strength is the stress at the maximum on the stress-strain curve. Or The greatest longitudinal or
axial stress a material can bear without breaking.
Tensile strength is the maximum amount of tensile stress that a material can take before failure. There
are three definitions of tensile strength
Yield strength
Ultimate strength
Breaking strength
YIELD STRENGTH
The stress at which material strain changes from elastic deformation to plastic deformation, causing it
to deform permanently. This point is not a well-defined point. We can say that yield strength is
a strength which a material can bear without permanent deformation.
Yield strength of Structural steel A36 is 250 MPa.
ULTIMATE STRENGTH
The maximum stress a material can withstand. Ultimate tensile strength of Structural steel A36 is 400
MPa.
BREAKING STRENGTH
The stress coordinate on the stress-strain curve at the point of rupture.
DIRECT STRESSES:
The Stresses which are acting normal to the plane of the body are called as normal or direct stresses.
These are called normal because these are acting perpendicular to the plane of the body.
SHEARING STRESSES:
The Stresses which act parallel to the stressed surfaces are called as shearing stresses.
TENSILE STRESSES:
If a straight bar is subjected to a pair of collinear forces acting in opposite direction and coinciding with
the ends of the bar and directed away from the bar, then the bar tends to increase in length and
the stresses developed in the bar will be tensile.
14
COMPRESSIVE STRESSES:
If a straight bar is subjected to a pair of collinear forces acting in opposite direction and coinciding with
the ends of the bar and directed towards the bar, then the bar tends to shorter in length and
the stresses developed will be compressive stresses.
SOLID MECHANICS OR MECHANICS OF SOLIDS
Solid mechanics or Mechanics of solids is the branch of Mechanics, Physics, and Mathematics that
concerns the behavior of solid matter under external actions (e.g., external forces, temperature changes,
applied displacements, etc.). Or it is a branch of science which deals with the internal effects of the
forces on the bodies when they are loaded, from initial point to rupture or break.
STRENGTH OF MATERIALS
Strength of materials deals with the relations between externally applied loads and their internal effects
on the bodies. Purpose of studying strength of materials to ensure that the structure used will be safe
against the maximum internal effects that may be produced by any combination of external loading.
TYPES OF FORCES
Forces that are acting on the body, may be of the following types. Effects of these forces are studied in
solid mechanics or mechanics of solids.
NORMAL FORCES
The forces that are acting perpendicular to the body are known as normal forces.
Normal forces are of two types:
1. Tensile
2. Compressive.
TANGENTIAL FORCES
The forces that are acting parallel to the body are known as tangential forces. Shear forces and frictional
forces are example of tangential forces.
INDEPENDENT FORCES
Active forces are independent forces.
DEPENDENT FORCES
Reactive forces are dependent forces.
CONCENTRATED FORCES
15
If forces are acting on an area of a body which is negligible as compared to the body, then these are
known as concentrated forces.
DISTRIBUTED FORCES
If forces are acting on an area of a body which is not negligible as compared to the body, then these are
known as distributed forces. These may be of uniformly distributed load (UDL) or uniformly varying
load (UVL) or any kind of general loading.
EFFECTS OF FORCES
The effects of forces which are studied in solid mechanics or mechanics of solids are
1. Translation
2. Rotation (moment and torque)
FATIGUE
In materials science, fatigue is the weakening of a material caused by repeatedly applied loads. It is the
progressive and localized structural damage that occurs when a material is subjected to cyclic loading.
The nominal maximum stress values that cause such damage may be much less than the strength of the
material typically quoted as the ultimate tensile stress limit, or the yield stress limit.
Fatigue occurs when a material is subjected to repeated loading and unloading. If the loads are above a
certain threshold, microscopic cracks will begin to form at the stress concentrators such as the surface,
persistent slip bands (PSBs), and grain interfaces.[1] Eventually a crack will reach a critical size, the
crack will propagate suddenly, and the structure will fracture. The shape of the structure will
significantly affect the fatigue life; square holes or sharp corners will lead to elevated local stresses
where fatigue cracks can initiate. Round holes and smooth transitions or fillets will therefore increase
the fatigue strength of the structure.
RESILIENCE
Resilience is the ability of a material to absorb energy when it is deformed elastically, and release that
energy upon unloading. Proof resilience is defined as the maximum energy that can be absorbed within
the elastic limit, without creating a permanent distortion. The modulus of resilience is defined as the
maximum energy that can be absorbed per unit volume without creating a permanent distortion. It can
be calculated by integrating the stress-strain curve from zero to the elastic limit. In uniaxial tension,
Where Ur is the modulus of resilience, σy is the yield strength, and E is the Young's modulus.
16
UNIT OF RESILIENCE
Resilience (Ur) is measured in a unit of joule per cubic meter (J·m–3) in the SI system, i.e. elastical
deformation energy per volume of test specimen (merely for gage-length part). Like the unit of
tensile toughness (UT), the unit of resilience can be easily calculated by using area underneath the
stress–strain (σ–ε) curve, which gives resilience value, as given below.
Fig: The area under the linear portion of a stress-strain curve is the resilience of the material Typical
Stress vs. Strain diagram for a ductile material (e.g. Steel).
MODULUS OF RIGIDITY
Is defined as the ratio of (a) longitudinal stress to longitudinal strain (b) shear stress to shear strain (c)
stress to strain (d) stress to volumetric strain just as the modulus of elasticity, E, relates tensile stress to
tensile strain, the modulus of rigidity, G, and relates shear stress to shear strain.
The modulus of rigidity, G, is, for isotropic materials, related to E as G = E/ (2(1+u)) where u = Poisson
ratio which varies from 0 to 0.5 and is usually 0.25-0.33 for many metals. Tensile stress = Ee e = tensile
strain
shear stress = Gk k = shear strain
WHAT IS A BULK MODULUS FOR A PERFECTLY RIGID BODY?
It is infinity. Now Bulk Modulus= Stress/Strain Now Strain in a perfectly rigid body=0Therefore Bulk
Modulus= Infinite for a perfectly rigid body
WHAT IS THE DIFFERENCE BETWEEN MODULUS OF ELASTICITY AND RIGIDITY?
We knew from Hook's law- "stress is proportional to strain."
So, stress = k * strain [here, k is a constant]
or, stress/strain= k
Now, if the stress and strain occurs due to axial force
then k is known as modulus of elasticity and it is denoted by E.
if the stress and strain occurs due to shear force
then k is known as modulus of rigidity and it is denoted by G.
RELATION BETWEEN YOUNG'S MODULUS SHEAR MODULUS AND BULK MODULUS?
Let young's modulus = E, Shear modulus = G, Bulk Modulus = K and poisson's ratio = v E = 3K(1-
2v) E = 2G(1+v)
17
WHAT IS THE MODULUS OF ELASTICITY OF WATER?
Pure de-aired water has a bulk modulus equal to approximately 2.2 GPa.
There is a common misconception that fluids are totally incompressible, however as can be seen from
the above this is not true (if it were, the bulk modulus would be infinitely high). It is reasonable to state
that water is highly resistant to compression however.
It should also be noted that the presence of dissolved gasses in water can significantly reduce this value
so consider carefully the application or system being modelled before choosing an elastic modulus for
water or any other fluid.
WHAT IS THE ELASTIC MODULUS OF LIMESTONE?
Intact Limestone can have a Young's modulus (E) ranging from:
9 GPa - 80 GPa.A,B
Poisson's ratio (v) for intact specimens varies from between:
0.2 - 0.3.B
Bulk modulus (K) derived from the above values using the following relation:
K = E / (3(1-(2v))
Bulk Modulus ranges from:
5 GPa - 66.67 GPa Shear modulus (G) derived from the above values using the following relation:
G = E / 2(1+v)
Shear modulus ranges from:
3.5 GPa to 33.33 GPa
Limestone is a natural earth material and so significant variability in stiffness properties may occur, as
such ranges of values are commonly quoted for the strength of rock and other geotechnical materials.
Ideally therefore the user would have access to specific lab test data for the rock type in question.
MODULUS OF RESILIENCE
The work done on a unit volume of material, as a simple tensile force is gradually increased from zero
to such a value that the proportional limit of the material is reached, is defined as the modulus of
resilience. This may be calculated as the area under the stress-strain curve from the origin up to the
proportional limit and is represented as the shaded area in the figure below.
18
MODULUS OF TOUGHNESS
The work done on a unit volume of material as a simple tensile force is gradually increased from zero
to the value causing rupture is defined as the modulus of toughness.
POISSON’S RATIO
When a bar is subject to a simple tensile loading there is an increase in length of the bar in the direction
of the load, but a decrease in the lateral dimensions perpendicular to the load. The ratio of the strain
in the lateral direction to that in the axial direction is defined as Poisson’s ratio.