31 useful references-facilitiespetrochemicals

Buildings Practice Facilities Plants/PetrochemicalsChapter 31

Useful References1 This chapter is included for purpose of general information pertinent to certain codes

& other requirements that can be referred to2 British & US codes references have been in general, included as used to be profes-

sional practice in past decades3 Currently in addition to those codes, EN codes have also been in practice4 Tried to enlist as many codes references, as could be practically, possible based on

available information 5 Also, tried my best to include, requirement pertinent certain software utilized on oil

projects6 Only, a few software scopes could be included after searching n medium

Software List in General1 OLGA 2000-dynamic/slugging study,

a (Olga is a Norwegian petroleum software originally, developed by IFE for Statoil in 1983.

b Olga 2000 is capable of one dimensional simulation of Oil, gas and water flows. c Olga is supposed to be used for: d Oil and natural gas flowlines or transportation lines, e Wet gas or condensate pipelines, f Well stream from a reservoir, g LNG / LPG/ NLG pipelines, h Dense phase pipelines, i Network of merging pipelines, j Artificial lift and other mass source injections, k Pipelines with process equipment (compressor, heat exchanger, separators, check-

valve, controller, mass source / sink), l Single phase gas or liquid, m Small diameter pipelines with various fluids, n Laboratory experiments)

2 INFOWORKS-drainage network modeling, (Potential use of software for urban drainage forecasting)

3 FRED- Shell FRED (fire, risk, explosion & dispersion) software, a Fault tree+ Fault tree, event tree & markov analysis software. b (Fault Tree Analysis uses tree structures to decompose system level failures into

combinations of lower level events and Boolean gates to model respective interactions.

c To address safety and ways failures or undesirable events that could occur, while trying to avoid them can be very challenging.

d To improve system safety and reliability, designers and analysts have to make better informed risk assessment decisions based on quantified evaluations of risks and effects, associated with alternative designs and other risk mitigating actions.

e These challenges are more compounded, where manual methods of fault isolation and risk analysis in large and complex systems are not viable.

f Using failure probability and system reliability data can assist in addressing undesirable events or challenges.

g Often times, Fault Trees are used in reliability and safety risk assessments to represent graphically, logical interactions and probabilities of occurrence of component failures and other events in a system.

Page 1 of 41 2012 Int. P Eng Suraj Singh


Useful Referencesh A Fault Tree analysis identifies and ranks combinations of events represented on a

Fault Tree, that cause system failure and provides estimates of system's failure probability.

i Using this detailed information, efforts to improve system safety and reliability can be highly focused and tailored to individual system by using quantitative results from data input. Additionally, Fault Tree analysis can help prevent failures from occurring by providing with data showing, how and under what circumstances, failure could occur, allowing for alternative measures to prevent (or design out) catastrophic failures or hazards.

j Boolean methodology and equations are used to construct and simplify Fault Tree. k As Fault trees are constructed, Boolean equations are used to evaluate Quantitative

and Qualitative characteristic of a critical system. l Qualitative analysis of Fault Tree determines:

i. Probability of system failure (top event) based on a single failure (basic event) cause or common cause potential using minimal cut sets,

ii. Combination of component failures (minimal cut sets), iii. Importance ranking of contributors to system failure.

m Quantitative analysis of Fault Tree focuses on probabilities of system and cut set failure or occurrence of top event based on probabilities of failure of basic events.)

4 T hazop- Hazop software, T risk- QRA tool, a (Software incorporates features and facilities that:b Serve as a framework, within which preparation for review can be structured.c Ease task of recording meeting minutes and help to maintain team's focus of attention

and interest.d Give speedy access to material useful to study team, such as previously, identified

problems, failure rate data and other such historical information. e Allow professionally, formatted reports to be produced with minimum of effort.f Permit additional management information to be extracted from study records.g Provide a comprehensive and easy to use system for effective action follow up and

close out, without significant administrative burden that this usually entails)

5 SACS- offshore structural analysis, a (SACS is an integrated finite element structural analysis suite of programs that

uniquely, provides for design, fabrication, installation, operations, and maintenance of offshore structures, including oil platforms and wind farms.

b Thirty-eight years of focus on these specialized requirements have made SACS analysis mainstay for most of world's offshore engineers.

c Virtually all of world's energy companies specify SACS software for use by their engineering firms across lifecycle of fixed offshore platforms.

d SACS provides comprehensive lifecycle applications for analysis and design of new and existing fixed offshore structures for oil, gas and wind energy markets.

e Comprehensive lifecycle applications include:f Non linear analysis for offshore platform failuresg Fatigue life evaluationh Foundation/structures, spars/topsides)

6 CAESAR II- pipe stress analysis, a (Intergraph CAESAR II evaluates structural responses and stresses of piping systems

to international codes and standards.



Useful Referencesb CAESAR II is pipe stress analysis standard against which all others are measured. ) c (Improved graphicsd Time saving modeling and analysis wizardse Improved analysis model creation and manipulationf The ability to view design models in analysisg Improved & more flexible report creationh Additional wind and seismic codesi Additional international piping codesj Enhanced hanger databases and design capabilitiesk Bi-directional links with CADWorx Plant Professional )

7 WANDA- liquid network simulation program including Unsteady hydraulic behavior, a (Wanda is an advanced, interactive software package to support hydraulic design

process of pipeline system. b Program is used for hydraulic analysis of steady and unsteady flow conditions in

arbitrary configured pipeline networks. c Primary subjects to evaluate and optimise a hydraulic design are flow capacity,

velocity, flow distribution, dynamic behaviour, economy, safety and control principles.

d With a hydraulic design, it can direct mechanical and process engineering to an effective and efficient system.

e Wanda can be applied to a variety of types of pipeline systems, like fire fighting systems, sewer systems, water distribution networks, industrial plants, oil pipelines, water cooling systems, hydropower plants and transportation systems for chemical products)a. WATNET- water network analysis,

8 TWO PHASE- steady state hydraulic analysis, 9 PIPE PHASE- steady state hydraulic analysis & complex network analysis, 10 TRANSIM- transient & dynamic analysis, 11 HYSYS-process simulation & modeling, 12 GAS- pressure drop calculation in gas pipeline, calculation of control valves,13 SENSYCALC- calculation of orifices, 14 VALTEC- valve sizing program, 15 NELSIZE- valve sizing program, 16 EDSA- electrical systems analysis & simulation, 17 LOADFLOW- calculation of electric load flow s/c & motor starting conditions, 18 CABLE- calculation of electric cable sizes, 19 VABI- calculation of lighting levels, 20 A/C LOAD- air conditioning calculation program, 21 TECHNOSOFT- structural calculation program, 22 MICROFEAP-finite element analysis program-structural engineering, 23 DECIDE- structural design of reinforced concrete, 24 STAAD PRO- structural analysis & design, 25 STRESS- 3 D structural calculations, 26 CONCRETE –concrete calculations, 27 CORSUR- corrosion data base, 28 MATHCAD- mathematical calculations- all disciplines, 29 MANIFOPRO v.5- GIS data processing

International



Useful ReferencesCodes & Standards Contractor to note that client shall not provide either these or any other international and national codes/standards/specifications. Survey and investigation works as provided in documents process

1 API 520 Part I and II Recommended practice for sizing, selection and installation of pressure relieving devices in refineries

2 API 521 Guide for pressure relieving and depressurising systems.3 API STD 610 Centrifugal pumps for petroleum, chemical and gas industry services4 API STD 613 Special purpose gear units for petroleum, heavy duty chemical and gas

industry services 5 API STD 617 Centrifugal pumps for petroleum, chemical and gas industry services 6 ASME Section VIII, Div. 1 Rules for construction of pressure vessels7 NACE MR 01-75 Standard material requirements, sulphide stress cracking materials

for oil field equipment8 API 2000 Venting atmospheric and low pressure storage tanks, fourth edition,

september, 1992.9 API 2610 Design, construction, operation, maintenance and inspection of terminals

and tank facilities

Mechanical 1 National Standards Not provided

Construction StandardsInstrumentation & Control (ICA)

International Standards BS 5308 Part 1 Instrument cables – polyethylene insulated cables

1 BS 5308 Part 2 Instrument cables – PVC insulated cables 2 BS 5345 Installation and maintenance requirements for electrical apparatus–type of

protection (I) 3 BS 6121 Cable Glands BS 7405 guide to selection of and application of flow meters

for measurement of fluid flow in closed conduits4 ISO 5167-1 Specification for square-edged orifice plates, nozzles and venturi tubes 5 ISO 5168 Methods of measurement of fluid flow estimation of uncertainty of a flow

rate measurement 6 ISO 5210 Industrial Valves – multi-turn valve actuators 7 ISO 5211 Industrial Valves – Part-Turn Valve Actuators TS/AS/009 Technical

Standard on Non-Relieving over Pressure Protection (Netherlands Steam Institute) 8 NACE MR-01-75 Material Requirements Sulphide Cracking Resistant Metallic

Material For Oil Field Equipment 9 IEC 60051 Direct Acting Indicating Analogue Electrical Measuring Instruments 10 IEC 60079 Electrical Apparatus for Explosive Gas Atmosphere 11 IEC 60227 Specification for PVC Insulation and Sheath of Electrical Cables IEC

60331 Fire Resisting Characteristics of Electrical Cables 12 ASTM A106 Standard specification for carbon steel pipes 13 ASTM D695 Standard test method for compressive properties of rigid plastics 14 ASTM D1599 Standard test method for short time hydraulic failure pressure of

plastic pipe, tubing and fittings 15 ASTM D2105 Standard test method for longitudinal tensile properties of “fiberglass”

(glass fiver reinforced thermosetting resin) pipe and tube



Useful References16 ASTM D2290 Standard test method for apparent tensile strength of ring or tubular

plastics and reinforced plastics by split disk method 17 ASTM D2412 Standard test method for determination of external loading

characteristics of plastic pipe by parallel plate loading 18 ASTM D2992 Standard practice for obtaining hydrostatic or pressure design basis for

“fiberglass” pipe and fittings19 ASTM D3517 Standard specification for “fiberglass” pressure pipe 20 ASTM D3567 Standard practice for determining dimensions of “fiberglass” Pipe and

fittings 21 ASTM D3681Standard test method for chemical resistance of “fiberglass” pipe in a

deflected condition22 ASTM D4161 Standard specification for “fiberglass” pipe joints using flexible

elastomeric seals 23 ASTM F412 Standard terminology relating to plastic piping systems 24 ASTM D883 Standard terminology relating to plastics 25 ASTM D1600 Standard terminology for abbreviated terms relating to plastics 26 ASTM D2310 Standard classification for machine made “fiberglass” pipe 27 ASTM D2517 Standard specification for reinforced epoxy resin gas pressure pipe and

fittings 28 ASTM D2996 Standard specification for filament wound “fiberglass” pipe 29 ASTM D2997 Standard specification for centrifugally, cast “fiberglass” pipe 30 ASTM D3262 Standard specification for “fiberglass” sewer pipe 31 ASTM D3754 Standard specification for “fiberglass” sewer and industrial pressure

pipe 32 ASTM D4024 Standard specification for machine made “fiberglass” flanges 33 ASTM F1173 Standard specification for thermosetting resin fiber glass pipe and

fittings to be used for marine applications 34 ASTM D3839 Standard practice for underground installation of “fiberglass” pipe 35 ASTM D790 Standard test method for flexural properties of un-reinforced &

reinforced plastics and electrical insulating materials 36 ASTM D2925 Standard test method for beam deflection of “fiber glass” pipe under

full bore flow 37 ASTM D2143 Standard test method for cyclic pressure strength of reinforced,

thermosetting plastic pipe 38 ASTM D1598 Standard test method for time to failure of plastic pipe under constant

internal pressure 39 ASTM D2924 Standard test method for external pressure resistance of “fiberglass”

pipe 40 ASTM C581 Standard practice for determining chemical resistance of thermosetting

resins used in glass fiber reinforced structures intended for liquid service 41 ASME B31.3 Process piping42 ASME B31.4 Pipeline transportation systems for liquid hydrocarbons and other

liquids 43 ANSI B16.5 Steel pipe flanges and flanged fittings 44 ANSI B16.9 Steel butt welding fittings 45 ANSI B16.10 Face-to-face and end-to-end dimensions of valves 46 ANSI B16.20 Metallic gaskets for pipe flanges - ring joint, spiral wound 47 ANSI B16.21 Nonmetallic flat gaskets for pipe flanges 48 ANSI B16.47 Large diameter steel flanges - NPS - 26" to 6049 ANSI B36.10 Welded and seamless wrought steel pipes



Useful References50 ANSI B36.19 Welded and seamless austenitic stainless steel pipe 51 BS 1868 Steel check valves for petroleum industry 52 BS 1873B Steel globe and check valves for petroleum industry53 S 5351 Steel ball valves for petroleum industry 54 BS 5352 Steel gate, globe and check valves, smaller than 2" NB 55 BS 6755 Testing of valves 56 BS EN 10204 Metallic products – type of inspection 57 NACE MR0175 Sulfide stress cracking resistant metallic

Materials for oilfield equipment 1 NACE RP0286 Electrical isolation of cathodically, protected pipelines 2 ISO 14692EJMA STD Standards of expansion joint manufacturers association, Inc

Civil and Structural 1 National standards/specifications

1 Client shall not supply copies of these/foregoing standards. 2 EPIC Contractor shall have to obtain its own copies from Ministry of Municipal

Affairs National Construction Specifications 3 National Highway Design Manual

Marine Breakwater 1 BS 6349- British standard code of practice for design of maritime structure2 US Army corps of engineers shore protection manual: 3 1984 CIRIA Report 154: 1991 – Manual on use of rock in coastal and shoreline

engineering Delft Hydraulics Report no 483: 1983 –Conceptual design of rubble mound breakwaters HR Wallingford Ltd R&D Technical Report W178.

4 Overtopping of seawalls–Design and assessment manual delft hydraulics computer program ‘breakwater’ version 3.0/latest conceptual design tool for breakwater structures

5 ES.2.14.0003 for Navigation aids, rev. a (listed under 5-b)

Telecommunication 1 CCWP FEED Phase- II: Mechanical specifications and references there to.

Also, references have been to various tender documents, during professional experience used for collection of information purpose only

1 AASHTO - American association of state highways and transportation officials 2 ACGIH - American conference of governmental industrial hygienists 3 ACI - American concrete institute 4 AGA - American gas association 5 AGMA - American gear manufacturers association 6 AISC - American institute of steel construction 7 ALPEMA - Brazed aluminum plate-fin heat exchanger manufacturers association 8 AMCA - Air movement and control association 9 ANSI - American national standards institute 10 API - American petroleum institute 11 API (MPMS) - API manual of petroleum measurement standards 12 ASCE - American society of civil engineers 13 ASHRAE - American society of heating, refrigeration, air conditioning 14 ASME - American society of mechanical engineers 15 ASTM - American society of testing and materials



Useful References16 ATEX - Atmosphere explosible 17 AWS - American welding society 18 BS - British standards 19 CINI - Stichting isolatie nederlandse industrie 20 CEB - Comite euro-international du beton 21 CICIND - International committee on industrial chimneys 22 CONCAWE - European organisation for environment, health and safety 23 DIN - Deutsches institut fur normung 24 EEMUA - Engineering equipment and materials users association 25 EIA - Electronics industry alliance 26 EJMA - Expansion joint manufacturers association 27 EN - Comite european de normalisation 28 ERA - Electronics representatives association 29 FCI - Fluid control institute 30 FEM - Federation europeene de la manutention 31 FIP - Federation internationale de la precontrainte 32 HEI - Heat exchange institution 33 HTFS - Heat transfer and fluid service 34 ICAO - International civil aviation organisation 35 IEC - International electrical committee 36 IEEE - Institute of electrical and electronic engineering 37 IP - Institute of petroleum 38 ISA - Instrument society of america 39 ISBN - International standard book number 40 ISGOTT - International safety guide for oil tankers and terminals 41 ISO - International organisation for standardisation 42 ISSMFE - International society for soil mechanics and foundation engineering 43 ITU - International telecommunications union 44 MIL-HDBK - US military handbook 45 MSS - Manufacturers standardisation society 46 NACE - National association of corrosion engineers NAMUR 47 NAS - National standards association 48 NEN - Nederlands normalisatie-institutuut 49 NFPA - National fire protection association 50 OCIMF - Oil companies international marine forum 51 PrEN - Draft EN standard 52 RAL - Deutsches institut fur gutesicherung und kennzeichnung 53 (RAL is an internationally, leading colour standard for all professional users of

colours in industry, trade, architecture and design.)54 SMACNA - Sheet metal and air conditioning contractors national association 55 SSPC - Steel structures painting council 56 TEMA - Standards of tubular exchanger manufacturers association 57 TIA - Telecommunications industry association 58 UBC - Uniform building code a (UBC was first published in 1927 by International Council of Building Officials. b It was intended to promote public safety and provided standardized requirements for

safe construction, which would not vary from city to city, as had previously been the case.

c Updated editions of the code were published approximately, every three years until 1997, which was final version of code.



Useful Referencesd UBC was replaced in 2000 by new International Building Code (IBC) published by

the International Building Council (ICC). e ICC was a merger of three predecessor organizations, which published three different

building codes. f These were:g International Council of Building Officials (ICBO) Uniform Building Codeh Building Officials and Code Administrators International (BOCA) BOCA National

Building Codei Southern Building Code Congress International (SBCCI) Standard Building Codej New ICC was intended to provide consistent standards for safe construction and

eliminate differences between three different predecessor codes. k It is primarily used in United States)

59 UL - Underwriters Laboratories Inc a (After 100 years as leading product safety testing and certification organization,

underwriters laboratories inc.b UL is synonymous with safety. c UL’s thorough, precise and independent methods have contributed to its reputation for

integrity and confidence and have made its mark most recognized and trusted symbol of safety.

d UL is an architect of US safety system having developed 1,040 product standards, outlines and actively, participates in national and international standards development.

e UL evaluates more than 19,450 types of products and 21 billion UL marks appear in marketplace.

f UL audits compliance through more than 600,000 inspections each year)

60 USEPA - United states environmental protection agency 61 VDE - Verband deutscher elektrotechniker a (Association for Electrical, Electronic & Information Technologies is one of the

largest technical and scientific associations in Europe) with more than 34 000 members.

62 VDI - Verein Deutscher Ingenieure (Association of German engineers)63 WRC - Welding research council

Appendices 1 AASHTO Guide for design of pavement structures 2 ACGIH Threshold limit values for chemical substances and physical agents, an biological

exposure indices 3 Advisory circular obstruction marking and lighting (issued by aviation administration) 4 AC70/7460-1K 5 AGA-9 Report 9, Measurement of gas: Ultrasonic meters 6 AGMA 6011 Specification for high speed helical gear units 7 AISC Steel construction manual 8 ALPEMA Plate-fin heat exchangers 9 AMCA Publication 203 Field performance measurement of fan systems 10 ANSI/ASME B1.1 Unified inch screw threads 11 ANSI/ASME B1.20.1 Pipe threads, General purpose (inch) 12 ANSI/ASME B16.3 Malleable iron threaded fittings classes 150 and 300 13 ANSI/ASME B16.5 Pipe flanges and flanged fittings NPS ½” to NPS 24” 14 ANSI/ASME B16.9 Factory-made wrought steel butt welding fittings



Useful References15 ANSI/ASME B16.10 Face-to-face and end to end dimensions of valves 16 ANSI/ASME B16.11 Forged steel fittings, socket-welding and threaded 17 ANSI/ASME B16.20 Metallic gaskets for pipe flanges - ring-joint, spiral-wound, and

jacketed 18 ANSI/ASME B16.21 Non-metallic flat gaskets for pipe flanges 19 ANSI/ASME B16.24 Cast copper alloy pipe flanges and flanged fittings 20 ANSI/ASME B16.25 Butt welding ends 21 ANSI/ASME B16.34 Valves: flanged, threaded and welding ends 22 ANSI/ASME B16.36 Orifice flanges 23 ANSI/ASME B16.47 Large diameter steel flanges NPS 26” to NPS 60” 24 ANSI/ASME B16.48 Steel line blinds 25 ANSI/ASME B16.104 Control valve seat leakage 26 ANSI/ASME B31.1 Power piping 27 ANSI/ASME B31.3 Process piping 28 ANSI/ASME B31.4 Pipeline transportation systems for liquid hydrocarbons and other

liquids 29 ANSI/ASME B31.5 Refrigeration piping 30 ANSI/ASME B31.8 Gas transmission and distribution piping systems 31 ANSI/ASME B36.10M Welded and seamless wrought steel pipe 32 ANSI/ASME B36.19M Stainless steel pipe 33 ANSI/ASME B46.1 Surface texture 34 ANSI B133.8 Gas turbine installation sound emissions 35 ANSI/FCI 70.2 Quality control standard for control valve seat leakage 36 ANSI/ISA S51.1 Process instrumentation terminology 37 ANSI/ISA S75.02 Control valve capacity test procedures 38 ANSI MC 96-1 Temperature measurement thermocouples 39 API (MPMS) Chapter 12 Calculation of petroleum quantities 40 API (MPMS) Chapter 2 Cylindrical tanks 41 API (MPMS) Chapter 4 Proving systems 42 API (MPMS) Chapter 5 Metering 43 API (MPMS) Chapter 6 Metering assemblies 44 API 5L Replaced by ISO 3183 45 API 6D Specification for pipeline valves 46 API 6FA Specification for fire test for valves 47 API 15LE Specifications for polyethylene (PE) line pipe 48 API 510 Pressure vessel inspection code: maintenance inspection, rating, repair and

alteration 49 API RP 520 Part 1 Sizing, selection, and installation of pressure relieving devices in

refineries 50 API RP 520 Part 2 Sizing, selection, and installation of pressure relieving devices in

refineries 51 API RP 521 Guide of pressure relieving and depressurizing system 52 API 526 Flanged steel pressure relief valves 53 API 527 Seat tightness of pressure relief valves 54 API 530 Refer ISO 13704 (Calculation of heater tube thickness in petroleum refineries) 55 API 536 Post combustion NOx control for fired equipment in general refinery services 56 API 541 Form-wound squirrel cage induction motors – 250 HP and larger 57 API 546 Form-wound brushless synchronous motors – 500 HP and larger 58 API 551 Process measurement instrumentation 59 API 552 Transmission systems



Useful References60 API 554 Process instruments and control 61 API 555 Process analysers 62 API 560 Refer ISO 13705 (Fired heaters for general refinery services) 63 API 582 Welding guidelines for chemical, oil and gas industries 64 API 594 Check valves; wafer, wafer-lug and double flanged type 65 API 598 Valve inspection and testing 66 API 600 Steel gate valves – flanged and butt welding ends, bolted and pressure seal

bonnets 67 API 601 Replaced by ANSI/ASME B 16.20 68 API 602 Compact carbon steel gate valves – flanged, threaded, welding and extended

body ends 69 API 608 Metal Ball valves – flanged, threaded and welding ends 70 API 609 Butterfly valves; double flanged, lug and wafer type 71 API 610 Centrifugal pumps for petroleum, petrochemical and natural gas industries – not

used – refer to BS EN ISO 13709 72 API 611 General purpose steam turbines for petroleum, chemical and gas industry

services 73 API 612 Special purpose steam turbines for petroleum, chemical and gas industry

services 74 API 614 Lubrication, shaft-sealing, and control-oil systems and auxiliaries for petroleum,

chemical and gas industry services 75 API 616 Gas turbines for petroleum, chemical and gas industry services 76 API 617 Axial and centrifugal compressors and expanders - compressors for petroleum,

chemical and gas industry services 77 API 618 Reciprocating compressors for petroleum, chemical and gas industry services 78 API 619 Rotary-type positive displacement compressors for petroleum, chemical and gas

industry services 79 API 631M Measurement of noise from air-cooled heat exchangers 80 API 650 Welded steel tanks for oil storage 81 API 662 Plate heat exchangers for general refinery services 82 API 670 Machinery protection systems 83 API 671 Special purpose couplings for petroleum, chemical and gas industry services 84 API 672 Packaged, integrally geared centrifugal air compressors for petroleum, chemical

and gas industry services 85 API 673 Centrifugal fans for petroleum, chemical and gas industry service 86 API 674 Positive displacement pumps - reciprocating 87 API 675 Positive displacement pumps - controlled volume 88 API 676 Positive displacement pumps - rotary 89 API 677 General purpose gear unit for petroleum, chemical and gas industry services 90 API 681 Liquid ring vacuum pumps and compressors 91 API 682 Shaft sealing systems for centrifugal and rotary pumps 92 API RP 686 Machinery installation and installation design 93 API 934 Materials & fabrication requirements for 2-1/4Cr-1MO & 3Cr-1Mo steel heavy

wall pressure vessels for high temperature, high pressure hydrogen service, 1st edition, 2000

94 API 945 Avoiding environmental cracking in amine units- latest edition. 95 API 2000 Venting atmospheric and low-pressure storage tanks, non refrigerated and

refrigerated 96 API 2218 Fireproofing practices in petrochemical processing plant 97 API 2510 Design and construction of LPG installations



Useful References98 API 2550 Method for measurement and calibration of upright cylindrical tanks 99 API RP 500 Classifications of locations for electrical installations at petroleum facilities

classified as class 1, division 1, division 2 100 API RP 505 Classifications of locations for electrical installations at petroleum

facilities classified as Class 1, Zone 0, Zone 1, and Zone 2 101 API RP 572 Inspection of pressure vessels 102 API RP 576 Inspection of pressure-relieving devices 103 API RP 651 Cathodic protection of aboveground petroleum storage tanks 104 ASCE Design of blast resistant buildings in petrochemical facilities 105 ASCE 7-95 Minimum design loads for buildings and other structures 106 ASHRAE Handbooks - Refrigeration 107 ASHRAE Handbook- HVAC applications 108 ASHRAE Handbook - Fundamentals 109 ASHRAE Handbooks - HVAC systems and equipment 110 ASHRAE 16 Method of testing for rating room air conditioners and packaged

terminal air conditioners 111 ASHRAE 23 Methods of testing for rating positive displacement refrigerant

compressors and condensing units 112 ASHRAE 30 Methods of testing liquid chilling package 113 ASHRAE 37 Methods of testing for rating unitary air-conditioning and heat pump

equipment 114 ASHRAE 40 Methods of testing for rating heat operated unitary air-conditioning

equipment for cooling 115 ASHRAE 52.1 Gravimetric and dust spot procedures for testing air cleaning

devices used in general ventilation for removing particulate matter 116 ASHRAE 55 Thermal environmental conditions for human occupancy and

addendum 117 ASHRAE 62 Ventilation for acceptable indoor air quality 118 ASHRAE 63.1 Method of testing liquid line refrigerant driers 119 ASHRAE 70 Method of testing for rating performance of air outlets and inlets 120 ASHRAE 79 Methods of testing for rating room fan-coil air conditioners 121 ASHRAE 111 Practices for measurement, testing, adjusting and balancing of

building heating, ventilation, air conditioning and refrigeration systems. 122 ASHRAE Guideline 1 HVAC commissioning process 123 ASHRAE Guideline 4 Preparation of operating and maintenance documentation

for building systems 124 ASHRAE Guideline 5 Commissioning of smoke management systems 125 AASHTO GDPS 4 Guide for design of pavement structures 126 AASHTO T180 Standard method of testing for moisture-density relations of soils

using a 4.45 kg rammer and 457 mm drop 127 ASME B16.3 Malleable iron threaded fittings, classes 150# & 300# 128 ASME PTC 1 General instructions for performance test codes 129 ASME PTC 4.1 Steam generating units 130 ASME PTC 4.4 Gas turbine heat recovery steam-generating units 131 ASME PTC 6 Steam turbines 132 ASME PTC 9 Displacement compressors 133 ASME PTC 10 Performance test code : compressors and exhausters 134 ASME PTC 16 Gas generators 135 ASME PTC 19.3 Temperature measurement – instruments and apparatus 136 ASME PTC 22 Performance test code : gas turbines



Useful References137 ASME PTC 26 Speed governing systems for internal combustion

engine/generator sets 138 ASME Section I Power boilers 139 ASME Section II Material specifications part A, B, C and D 140 ASME Section III Creep design basis fatigue analysis 141 ASME Section IX Qualification standard for welding and brazing procedures 142 ASME Section V Non-destructive examination 143 ASME Section VIII Div. 1 and 2, Boiler and vessel code 144 ASME RTP-1 Reinforced thermoset plastic corrosion resistant material 145 ASTM A 48 Standard specification for gray iron castings 146 ASTM A53 Standard specification for pipe, steel, black and hot dipped, zinc

coated, welded and seamless 147 ASTM A 105/105M Forgings, carbon steel, for piping applications 148 ASTM A 106 Seamless carbon steel pipe for high temperature service 149 ASTM A 123/A123M Standards - specification for zinc (hot dip galvanised)

coating on iron and steel products, version a 150 ASTM A 167 Standard specification for stainless and heat resisting chromium-

nickel steel plate, sheet and strip 151 ASTM A 179/A179M Seamless cold-drawn low-carbon steel heat-exchanger and

condenser tubes 152 ASTM A 182/A182M Forged or rolled alloy-steel pipe flanges, forged fittings,

and valves and parts for high-temperature 153 ASTM A 193/A193M Standard specification for alloy steel, stainless steel and

stainless steel bolting materials for high temperature service 154 ASTM A 194/A194M Standard specification for carbon alloy and steel nuts for

bolts for high pressure or high temperature service, or both 155 ASTM A 213/A213M Seamless ferritic and austenitic alloy - steel boiler,

superheater and heat-exchanger tubes 156 ASTM A 216/A216M Specification for carbon steel castings, suitable for fusion

welding, for high temperature service 157 ASTM A 234/A234M Pipe fittings of wrought carbon steel and alloy steel for

moderate and elevated temperatures 158 ASTM A 240/A240M Standard specification for heat resisting chromium nickel

stainless steel plate, sheet, and strip for pressure vessels 159 ASTM A 262 Standard practices for detecting susceptibility to intergranular

attack in austenitic stainless steels 160 ASTM A 269 Standard specification for seamless and welded austenitic stainless

steel tubing for general service 161 ASTM A 276 Standard specification for stainless steel bars and shapes 162 ASTM A 285 Standard specification for pressure vessel plates, carbon steel, low

and intermediate-tensile strength 163 ASTM A 307 standard specification for carbon steel bolts and studs, 60,000 p.s.i.

tensile strength 164 ASTM A 312/A312M Seamless and welded austenitic stainless steel pipes for

general service 165 ASTM A 320/A320M Alloy-steel bolting materials for low-temperature service 166 ASTM A325 Standard specification for structural bolts, steel, heat treated,

120/105 ksi minimum tensile strength-AASHTO no:M164. 167 ASTM A 333/A333M Seamless and welded steel pipe for low-temperature

service



Useful References168 ASTM A 334/A334M Seamless and welded carbon and alloy - Steel tubes for

low-temperature service 169 ASTM A335 Standard specification for seamless ferritic alloy-steel pipe for high-

temperature service 170 ASTM A 350/A350M Forgings, carbon and low-alloy steel, requiring notch

toughness testing for piping components 171 ASTM A 351/A351M Specification for steel castings, austenitic, for high

temperature service 172 ASTM A 352/A352M Specification for steel castings, ferritic and martensitic, for

pressure containing parts suitable for low temperature service 173 ASTM A 353/A353M Pressure vessel plates, alloy steel, 9% nickel, double

normalised and tempered 174 ASTM A 358/A358M Standard specification for electric-fusion-welded austenitic

chromium-nickel alloy steel pipe for high temperature service 175 ASTM A 388/A388M Practice for ultrasonic examination of heavy steel forgings 176 ASTM A 392 Standard specification for zinc coated steel chain link fence fabric 177 ASTM A395 Standard specification for ferritic ductile iron pressure-retaining

castings for use at elevated temperatures 178 ASTM A 403/A403M Wrought austenitic stainless steel piping and fittings 179 ASTM A 420/A420M Piping fittings of wrought carbon steel and alloy steel for

low-temperature service 180 ASTM A 450/A450M Standard specification for carbon, ferritic alloy and

austenitic alloy steel tubes 181 ASTM A 453/A453M Standard specification for high temperature bolting

materials, with expansion coefficients comparable to austenitic steels 182 ASTM A 463/A463M Standard specification for steel sheet, aluminium-coated by

hot-dip process 183 ASTM A 491 Standard specification for aluminium coated steel chain link fence

fabric 184 ASTM A 516/A516M Pressure vessel plates, carbon steel, for moderate and

lower-temperature service 185 ASTM A 522/A522M Forged and rolled 8 and 9% nickel alloy steel flanges,

fittings, valves and parts for low-temperature service 186 ASTM A 525/A525M Specification for general requirements for steel sheet, zinc

coated (galvanised) by hot dip process 187 ASTM A 530 Standard specification for general requirements for specialized

carbon and alloy steel pipe 188 ASTM A 537/A537M Pressure vessel plates, heat treated, carbon-manganese-

silicon steel 189 ASTM A 553/A553M Pressure vessel plates, alloy steel, quenched and tempered

8 and 9 percent nickel 190 ASTM A 609 Specification for longitudinal-beam ultrasonic inspection for carbon

and low-alloy steel castings 191 ASTM A671 Standard specification for electric-fusion-welded steel pipe for

atmospheric and lower temperatures 192 ASTM A672 Standard specification for electric-fusion-welded steel pipe for high

pressure service at moderate temperature 193 ASTM A 765/A765M Carbon steel and low-alloy steel pressure-vessel-

component forgings with mandatory toughness requirements 194 ASTM A 770/A770M Specification for through-thickness tension testing of steel



Useful Referencesplate for special applications

195 ASTM A 790/A 790M Standard specification for seamless and welded ferritic/austenitic stainless steel pipe

196 ASTM A961 Standard specification for carbon and alloy steel pipe, electric-fusion-welded for high pressure service at high temperature

197 ASTM B 148 Specification for aluminum bronze sand castings 198 ASTM B 165 Standard specification of nickel-copper alloy 199 ASTM B 209 Standard specification for aluminium and aluminium alloy sheet

and plate 200 ASTM B 418 Standard specification for cast and wrought galvanic zinc anodes 201 ASTM B 423 Standard specification for seamless and electric welded low-alloy

steel tubes 202 ASTM B 574 Standard specification for low-carbon nickel-molybdenum-

chromium, low-carbon nickel-chromium-molybdenum, low- carbon nickel-molybdenum-chromium-tantalum, low-carbon nickel-chromium-molybdenum-copper, and low-carbon nickel-chromium-molybdenum-tungsten alloy rod

203 ASTM B 637 Standard specification for precipitation-hardening nickel alloy bars, forgings, and for going stock for high temperature service

204 ASTM B 668 Standard specification for UNS N08028 seamless pipe and tube 205 ASTM B 695 Standard specification for coatings of zinc mechanically deposited

on iron and steel 206 ASTM B 764-04 (Includes change to title) test method for simultaneous thickness

and electrode potential determination of individual layers in multilayer nickel deposit step test (R)

207 ASTM B 839-04 Test method for residual embrittlement in metallic coated, externally threaded articles, fasteners, and rod – inclined wedge method (r)

208 ASTM B 851-04 Specification for automated controlled shot peening of metallic articles prior to nickel, autocatalytic nickel, or chromium plating, or as final finish

209 ASTM C 27 Standard classification of fireclay and high-alumina refractory brick 210 ASTM C 155 Standard classification of insulating firebrick 211 ASTM C 165 Standard test method for measuring compressive properties of

thermal insulation 212 ASTM C 167 Standard test method for thickness and density of blanket or batt

insulations 213 ASTM C 177 Standard test method for steady-state heat flux measurements and

thermal transmissions properties by means of guarded hot plate apparatus 214 ASTM C 240 Standard test method of testing cellular glass insulating block 215 ASTM C 273 Test for shear properties in flatwise plane or flat sandwich

constructions or sandwich cores 216 ASTM C 303 Standard test method for dimensions and density of performed

block-type thermal insulation 217 ASTM C 390 Criteria for sampling and acceptance of pre formed thermal

insulation lots 218 ASTM C 401 Standard classification of alumina and alumina-silicate castable

refractories 219 ASTM C 461 Standard test method of mastic and coating used in conjunction

with thermal insulation 220 ASTM C 518 Standard test method for steady state heat flux measurements and

thermal transmission properties by means of heat flow meter 221 ASTM C 533 Standard specification for calcium silicate block and pipe thermal



Useful Referencesinsulation

222 ASTM C 547 Standard specification for mineral fibre pipe insulation 223 ASTM C 552 Standard specification for cellular glass thermal insulation 224 ASTM C 585 Standard practice for inner and outer diameters of rigid thermal

insulation for nominal sizes of pipe and tubing (NPS system) 225 ASTM C 591 Standard specification for unfaced pre formed rigid cellular

polyisocyanurate thermal insulation 226 ASTM C 592 Standard specification for mineral fibre blanket insulation and

blanket-type pipe insulation 227 ASTM C 612 Specification for mineral fibre block and board thermal insulation 228 ASTM C 623 Standard test method for young’s modulus, shear modules and

poisson's ratio for glass and glass ceramics by resonance 229 ASTM C 680 Standard practice for determination of heat gain or loss and surface

temperatures of insulated pipe and equipment 230 systems by use of a computer program 231 ASTM C 795 Standard specification for thermal insulation for use in contact with

austenitic stainless steel 232 ASTM C 871 Standard test methods for chemical analysis of thermal insulation

materials for leachable chloride, fluoride, silicate and sodium ions 233 ASTM C 876 Standard test method for half cell potentials of uncoated reinforcing

steel in concrete 234 ASTM C 892 Standard specification for high temperature fibre blanket thermal

insulation 235 ASTM C 1497-04 Specification for cellulosic fiber stabilized thermal insulation

(R) 236 ASTM D 312 Standard specification for asphalt used in roofing 237 ASTM D 420 Guide to site characterization for engineering, design and

construction purposes 238 ASTM D 511 Test method for calcium and magnesium in water 239 ASTM D 512 Test method for chloride ion in water 240 ASTM D 513 Test methods for carbon dioxide, total and dissolved, in water 241 ASTM D 516 Test method for sulphate ion in water 242 ASTM D 5162 Standard practice for discontinuity (holiday) testing of non-

conductive protective coating on metallic substrates 243 ASTM D 610 Test methods for evaluating degree of rusting on painted steel

surfaces 244 ASTM D 635 Test method for rate of burning and/or extent and time of burning

of self-supporting plastics in a horizontal position 245 ASTM D 653 Terminology relating to soil, rock and contaminated fluids 246 ASTM D 790 Standard test methods for flexural properties of un-reinforced and

reinforced plastics and electrical insulating materials 247 ASTM D 1066 Practice for sampling steam 248 ASTM D 1126 Test methods for hardness in water 249 ASTM D 1248 Specification for polyethylene plastics moulding and extrusion

materials 250 ASTM D 1250 Standard guide for petroleum measurement tables 251 ASTM D 1293 Test method for pH of water 252 ASTM D 1426 Test methods for ammonia nitrogen in water 253 ASTM D 1452 Practice for soil investigation and sampling by auger borings 254 ASTM D 1557 Standard test methods for laboratory compaction characteristics of



Useful Referencessoil using modified effort

255 ASTM D 1587 Practice for thin-walled tube geotechnical sampling of soils 256 ASTM D 1621 Standard test method for compressive properties of rigid cellular

plastics 257 ASTM D 1622 Standard test method for apparent density of rigid cellular plastics 258 ASTM D 1623 Standard test method for tensile adhesion properties of rigid

cellular plastics 259 ASTM D 2487 Standard practice for classification of soils for engineering

purposes 260 ASTM D 2563 Practice for classifying visual defects in glass reinforced plastic

laminate parts 261 ASTM D 2583 Standard test method for indention hardness of rigid plastics by

means of barcol impressor 262 ASTM D 2856 Standard test method for open cell content of rigid cellular plastics

by air pycnometer 263 ASTM D 3014 Standard test method for flame height, time of burning and loss of

mass of rigid thermoset cellular plastics in a vertical position 264 ASTM D 3039/3039M Test method for tensile properties of polymer matrix

composite materials 265 ASTM D 3370 Practice for sampling water from closed circuits 266 ASTM D 3441 Deep, quasi-static cone and friction cone penetration tests of soil 267 ASTM D 3744 Test method of aggregate durability index 268 ASTM D 3764 Standard practice for validation of process stream analysers 269 ASTM D 4541 Standard test method for pull and off strength of coating using

portable adhesion testers. 270 ASTM D 5162 Standard practice for discontinuity (holiday) testing of non-

conductive protective coating on metallic substrates 271 ASTM D 6122 Standard practice for validation of multivariate process infrared

spectrophotometers 272 ASTM E 162 Standard test method for surface flammability of materials using a

radiant heat source 273 ASTM E 21 Elevated temperature tension test of metallic materials 274 ASTM E 84 Standard test method for surface burning characteristics of building

materials 275 ASTM E 94 Standard guide for radiographic testing 276 ASTM E 96 Standard test method for measurement of water vapour transmission

of materials 277 ASTM E 110 Standard test method for indentation hardness of metallic materials

by portable hardness testers 278 ASTM E 165 Standard test method for liquid penetrant examination 279 ASTM E 413-04 Classification for rating sound insulation (R) 280 ASTM E 446 Reference radiographs for steel castings up to 2in. (51mm) in

thickness 281 ASTM E 709 Standard guide for magnetic particle examination 282 ASTM E 966-04 Guide for field measurement of airborne sound insulation of

building facades and façade elements (R) 283 ASTM E 1687-04 Test method for determining carcinogenic potential of virgin

base oils in metalworking fluids (R) 284 ASTM E 1972-04 Practice for minimizing effects of aerosols in wet metal

removal environment (R)



Useful References285 ASTM E 2235-04 Test method for determination of decay rates for use in sound

insulation test methods (R) 286 ASTM F 552 Standard terminology relating to chain link fencing 287 ASTM F 567 Standard practice for installation of chain link fence 288 ASTM F 668 Standard specification for polyvinyl chloride (PVC) and other

organic polymer-coated steel chain link fence fabric 289 ASTM F 1043 Standard specification for strength and protective coatings on

metal industrial chain link fence framework 290 ASTM F 1249 Test method for water vapour transmission rate through plastic

film and sheeting using a modulated infra red sensor 291 ASTM G 57 Standard test method for field measurement of soil resistivity using

Wenner four electrode method 292 ASTM G 93 Cleaning methods for material and equipment used in oxygen

enriched environments 293 ASTM SI-10 Practice for use of international system of units (SI) 294 ASTM Volume 04.03 Traveled surface characteristics 295 ASTM Volume 04.08 Natural building stones; soil and rock 296 ASTM Volume 11.01 Water (I) 297 ASTM Volume 11.02 Water (II) 298 ATEX Directives Protective equipment and systems intended for use in

potentially explosive atmospheres; 299 AWWA M45 Fibreglass pipe design- Latest Edition 300 AWS A5.1 Specification for covered carbon steel arc welding electrodes 301 AWS A5.11A5.11M Nickel and nickel alloy welding electrodes for shielded

metal arc welding 302 AWS A5.14/A5.14M Nickel and nickel alloy bare welding electrodes and rods 303 AWS A5.17/A5.17M Specification for carbon steel electrodes and fluxes for

submerged arc welding 304 AWS A5.18 Specification for carbon steel filler metals for gas shielded arc

welding 305 AWS A5.4 Specification for stainless steel electrodes for shielded metal-arc

welding 306 AWS A5.5 Specification for low alloy steel covered arc welding electrodes 307 AWS A5.9 Bare stainless steel welding electrodes and rods 308 AWS D1.1/D1.1M Structural welding code steel 309 BS 88 Cartridge fuses for voltages up to and including 1000V AC and 1500V DC 310 BS 171D Identification of pipe lines and services. BSI, UDC (621.643/644) –

777.6 311 BS 336 Specification for fire hose couplings and ancillary equipment 312 BS 381C Colours for identification, coding and special purposes 313 BS 417 Specification for galvanised low carbon steel cisterns, cistern lids, tanks

and cylinders 314 BS 449 Use of structural steel in buildings 315 BS 466 Specification for power driven overhead travelling cranes, semi goliath

and goliath cranes for general use 316 BS 476 Fire tests on building materials and structures 317 BS 476-3 Fire tests on building materials and structures – Part 3: classification

and method of test for external exposure to roofs 318 BS 599 Methods of testing pumps 319 BS 709 Methods of destructive testing fusion welded joints and weld metal steel



Useful References320 BS 729 Hot dip galvanized coatings on iron and steel articles 321 BS 743 Specification for materials for damp proof courses 322 BS 747 Specification for reinforced bitumen roofing 323 BS 750 Specification for underground fire hydrants and surface box frames and

covers. 324 BS 812 – 123 Testing aggregates - Method for determination of Alkali-silica

reactivity - concrete prism method 325 BS 848 Fans for general purpose 326 BS 952 Glass for glazing 327 BS 1113 Specification for design and manufacture of water-tube steam generating

plant etc 328 BS 1133 Packaging code 329 BS 1184 Specification for copper & copper alloy traps 330 BS 1188 Ceramic wash basins and pedestals 331 BS 1191 Specification for gypsum building plasters 332 BS 1230 Gypsum – plasterboard 333 BS 1245 Specification metal door frame (steel) 334 BS 1253 Gullies for buildings 335 BS 1376 Specification for colours of light signals 336 BS 1377 Methods of tests for soils for civil engineering purposes – parts 1 to 9 337 BS 1377 Methods of test for soils for civil engineering purposes. Part 3 chemical

and electrochemical tests, part 9 in-situ tests. 338 BS 1414 Specification for steel wedge gate valves (flanged and butt welding

ends) for petroleum, petrochemical and allied industries 339 BS 1449 Specification for steel plate, sheet and strip 340 BS 1494 Specification for fixing accessories for building purposes. 341 Fixing for sheets, roof and wall coverings 342 BS 1501 Steel for pressure purposes 343 BS 1503 Specification for steel forgings for pressure purposes 344 BS 1521 Specification for waterproof building papers 345 BS 1635 Recommendations for graphical symbols and abbreviations for fire

protection drawings 346 BS 1640 Steel butt-welding pipe fittings for petroleum industry 347 BS 1722 Part 10 Fences - part 10: Specification for anti-intruder fences in chain-

link and welded mesh 348 BS 1726 Coil springs 349 BS 1787 Steel windows for industrial windows 350 BS 1868 Specification for steel check valves (flanged and butt welding ends) for

petroleum, petrochemical and allied industries 351 BS 1873 Specification for steel globe and globe stop valves (flanged and butt

welding ends) for petroleum, petrochemical and allied industries 352 BS 1876 Specification for automatic flush cisterns for urinals 353 BS 1881 Testing concrete 354 BS 1990-1 Wood poles for overhead power and telecommunications lines 355 BS 2000 – Part 72 'Methods of test for petroleum and its products part 72 -

determination of viscosity of cutback bitumen' 356 BS 2080 Specification for face to face, centre to centre, end to end and centre to

end dimensions of valves 357 BS 2573 Rules for design of cranes 358 Part 1 Specification for classification, stress calculations and design criteria for



Useful Referencesstructures

359 Part 2 and AMD 3952 and AMD 5013 Specification for classification, stress calculations and design of mechanisms

360 BS 2654 Specification for manufacture of vertical steel welded non-refrigerated storage tanks with butt welded shells for petroleum industry

361 BS 2690 Methods of testing water used in industry 362 BS 2853 design and testing of steel overhead runway beams 363 BS 2972 Methods of test for inorganic thermal insulating materials 364 BS 2997 Specification for Aluminium Rainwater Goods 365 BS 3083 Specification for Hot Dipped and Hot Dipped Aluminium/Zinc Coated

corrugated steels sheets for general purposes 366 BS 3148 Methods of test for water and making concrete 367 BS 3165 Specification for rubber and plastics suction hoses and hose assemblies

for fire-fighting purposes 368 BS 3381 Spiral Wound Gaskets for Steel Flanges to BS 1560 369 BS 3402 Specification for Quality Vitreous China Sanitary Appliances 370 BS 3505 Specification for unplasticized polyvinyl chloride (U-PVC) pressure

pipes for cold potable water 371 BS 3573 Specification for polyolefin copper conductor telecommunication cables 372 BS 3602 Specification for steel pipes and tubes for pressure purposes; carbon and

carbon manganese steel with specified elevated temperature properties 373 BS 3603 Specification for carbon and alloy steel pipes and tubes with specified

low temperature properties for pressure purposes 374 BS 3605 Austenitic Stainless steel pipes and tubes for pressure purposes 375 BS 3606 Specification for steel tubes for heat exchangers 376 BS 3621 Specification for Thief Resistant Locks 377 BS 3790 Specification for endless wedge belt drives and endless V-belt drives 378 BS 3958 Thermal insulating material 379 BS 3974 Specification on pipe supports 380 BS 4022 Specification for pre-fabricated gypsum plasterboard 381 BS 4027 Specification for sulphate resisting Portland cement 382 BS 4076 Steel Chimneys 383 BS 4082 External dimensions for vertical in-line centrifugal pumps. 384 BS 4131 Terrazzo Tiles 385 BS 4211 Specification for ladders for permanent access to chimneys, other high

structures, silos and bins 386 BS 4320 Specification for metal washers for general engineering purposes 387 BS 4346 Joints and fittings for use with unplasticized PVC pressure pipes 388 BS 4370 Methods of test for rigid cellular materials 389 BS 4449 Carbon steel bars for reinforcement of concrete 390 BS 4483 Steel fabric for reinforcement of concrete 391 BS 4514 Un-plasticised PVC Soil and Ventilation Pipes of 82.4mm mean outside

diameter and accessories of 82.4mm and other sizes 392 BS 4721 Specification for Ready Mixed Building Mortars 393 BS 4735 Laboratory methods of tests for assessment of horizontal burning

characteristics of specimens no larger than 150mm x 50mm x 13mm of cellular plastics and cellular rubber materials when subjected to a small flame

394 BS 4787 Internal and External Wood door sets, door leaves and frames 395 BS 4800 Schedule of paint colours for building purposes 396 BS 4868 Profiled Aluminium Sheet for Buildings



Useful References397 BS 4880 Urinals, Stainless Steel Slab Urinals 398 BS 4882 Specification for bolting for flanges and pressure containing purposes 399 BS 4991 Specification for propylene copolymer pressure pipe 400 BS 4999-140 General requirements for rotating electrical machines 401 BS 4999-144 General requirements for rotating electrical machines Part 144:

Specification for insulation of bars and coils of high 402 voltage machines, including test methods 403 BS 5041-1 Fire hydrant systems equipment-Specification for landing valves for

wet risers 404 BS 5041-2 Fire hydrant systems equipment-Specification for landing valves for

dry risers 405 BS 5051 Specification for Security Glazing 406 BS 5135 and AMD 5172 Specification for arc welding of carbon and carbon

manganese steels 407 BS 5224 Masonry Cement 408 BS 5234 Partitions (including Matching Linings) 409 BS 5250 Code of Practice for Control of Condensation in Buildings 410 BS 5262 Code of Practice for External Rendered Finishes 411 BS 5306 Part 0 Guide for Selection of Installed Systems and Other Fire

Equipment 412 BS 5306 Part 1 Hydrant Systems, Hose Reels and Foam Inlets 413 BS 5306 Part 2 Specification for Sprinkler Systems 414 BS 5306 Part 4 Specification for Carbon Dioxide Systems 415 BS 5306 Section 6.1 Specification for Low Expansion Foam Systems 416 BS 5306 Section 6.2 Specification for Medium and High Expansion Foam

Systems 417 BS 5306 Part 7 Specification for Powder Systems 418 BS 5308 Instrumentation cables 419 BS 5351 Specification for Steel Ball Valves for Petroleum, Petrochemical and

Allied Industries 420 BS 5352 Specification for steel wedge gate, globe and check valves 50mm and

smaller for petroleum, petrochemical and allied industries 421 BS 5353 Steel plug valves 422 BS 5357 Code of Practice for Installation of Security Glazing 423 BS 5368 Methods for Testing Windows 424 BS 5385 Code of Practice for Design and Installation of Ceramic Floor, Wall

Tiles and Mosaics 425 BS 5395 Part 2 Code of Practice for Design of Helical & Spiral Stairs 426 BS 5395 Part 3 Code of Practice for Design of Industrial Type Stairs, permanent

ladders and walkways 427 BS 5422 Methods for specifying thermal insulating materials on pipes, ductwork

and equipment (in temperature range-40°C to+700°C) 428 BS 5427 Code of Practice for use of profiled sheet for roof and wall cladding on

buildings 429 BS 5492 Code of Practice for Internal Plastering 430 BS 5499 Code of Practice for Escape Signs, Route Signage, Safety Signs

including Fire Safety Signs 431 BS PD 5500 Specification for unfired fusion welded pressure vessels 432 BS 5503 Specification for Vitreous China washdown WC pans with horizontal

outlet



Useful References433 BS 5504 Specification for wall hung WC pans 434 BS 5506 Specification for wash basins 435 BS 5520 Specification for Vitreous chain bowl urinals (rimless type) 436 BS 5588 Fire Precautions in Design, Construction and Use of Buildings 437 BS 5628 Code of Practice for structural use of Masonry 438 BS 5642 Sills and Copings, Specification for Sills and Copings of Pre-Cast

Concrete, Cast Stone, Clay ware, Slate & Natural Stone 439 BS 5713 Specification for Hermetically sealed flat double glazing units 440 BS 5731-4 Specification for aluminium and aluminium alloy 441 BS 5744 Code of practice for safe use of cranes 442 BS 5750 Quality systems 443 BS 5872 Specification for locks and latches for doors in Buildings 444 BS 5977 Lintels – Method of Assessment of Loads 445 BS 5930 Code of practice for site investigation 446 BS 5950 Structural use of steelwork in building 447 BS 5970 Code of practice for thermal insulation of pipework and equipment (in

temperature range of -100oC to +870oC) 448 BS 5996 Ultrasonic testing and specifying quality grades of ferritic steel plate 449 BS 6072 and AMD 3960, Method for magnetic particle flaw detection 4542 and

4843 450 BS 6073 Pre-cast Masonry Units 451 BS 6100 Part 1 Glossary of building and civil engineering terms - Part 1: General

and miscellaneous 452 BS 6100 Part 2 Glossary of building and civil engineering terms - Part 2: Civil

engineering 453 BS 6150 Code of Practice for Painting of Buildings 454 BS 6031 Code of practice for earthworks' 455 BS 6121 Specification for mechanical cable glands 456 BS 6217 Code of Practice for Built up felt roofing 457 BS 6218 Code of Practice for Mastic Asphalt Roofing 458 BS 6229 Code of Practice for Flat Roofs with continuously supported covering 459 BS 6231 Specification for PVC-insulated cables for switchgear and control gear

wiring 460 BS 6259 Code of Practice for design, planning, installation, testing and

maintenance of sound systems 461 BS 6262 Code of Practice for Glazing of Buildings 462 BS 6290-4 Lead-acid stationary cells and batteries 463 BS 6349 Code of practice for maritime structures - Part 1 through Part 7 464 BS 6364 Specification for valves for cryogenic service 465 BS 6375 Performance of Windows 466 BS 6387 Specification for performance requirements for cables required to

maintain circuit integrity under fire conditions 467 BS 6398 Specification for Bitumen Damp-proof Courses for Masonry 468 BS 6399-1 Loading for buildings – Part 1 Code of Practice for dead and imposed

loads 469 BS 6399-2 Loading for buildings – Part 2 Code of Practice for wind loads 470 BS 6399-3 Loading for buildings – Part 3 Code of Practice for imposed roof loads 471 BS 6431 Ceramic Floor and Wall Tiles 472 BS 6437 Specification for polyethylene pipes (type 50) in metric diameters for

general purposes



Useful References473 BS 6452 Beads for Internal Plaster & Dry Linings 474 BS 6467 Electrical Apparatus with protection by enclosure for use in presence of

combustible dusts 475 BS 6510 Specification for steel windows, sills, window boards and doors 476 BS 6510 Steel sub-frames, sills & window boards for metal windows 477 BS 6515 Specification for Polyethylene Damp Proof Courses for Masonry 478 BS 6572 Specification for Blue Polyethylene pipes up to nominal size 63 for

below ground use for portable water 479 BS 6651 Code of practice for protection of structures against lightning 480 BS 6656 Guide to prevention of inadvertent ignition of flammable atmosphere by

radio frequency radiation 481 BS 6701 Telecommunications equipment and telecommunications cabling –

specification for installation, operation and maintenance. 482 BS 6730 Specification for black polyethylene pipes up to nominal size 63 for

above ground use for cold potable water 483 BS 6755 Inspection and testing of valves. Parts 1 and 2 484 BS 6883 Elastomer insulated cables for fixed wiring in ships and on mobile and

fixed offshore units 485 BS 6941 Specification for electrical apparatus for explosive atmospheres with

type of protection N 486 BS 6925 Specification for Mastic Asphalt for Building & Civil Engineering 487 BS 7121 Code of practice for safe use of cranes. 488 Part 1 and AMD 9093 General 489 Part 2 Inspection testing and examination 490 BS 7281 Specification for polyethylene pipes for supply of gaseous fuels 491 BS 7354 Code of practice for design of high-voltage open terminal stations 492 BS 7357 7.5 litre WC flushing cistern 493 BS 7361-1 Cathodic Protection 494 BS 7364 Specification for Galvanised Steel Studs and Channels for Stud and

Sheet Partitions using Screw Fixed Gypsum Wallboard 495 BS 7953 Entrance Flooring Systems, Selection, Installation and Maintenance 496 BS 8004 Code of practise for Foundations 497 BS 8007 Code of practice for design of concrete structures for retaining aqueous

liquids 498 BS 8102 Code of Practice for Protection of Structures Against Water from

Ground 499 BS 8110 Structural use of concrete 500 BS 8203 Code of Practice for Installation of Resilient Floor Coverings 501 BS 8204 Screeds, Bases and In-situ Flooring, Concrete Bases and Cement Sand,

Screed to Receive Flooring 502 BS 8207 Code of Practice for Energy Efficiency in Buildings 503 BS 8212 Code of Practice for Dry Lining and Partitions using Gypsum

Plasterboard 504 BS 8214 Fire Door assemblies with non-metallic leaves 505 BS 8215 Code of Practice for Design and Installation of Damp-proof Courses in

Masonry Construction 506 BS 8217 Code of Practice for Built-up Felt Roofing 507 BS 8218 Code of Practice for Mastic Asphalt Roofing 508 BS 8290 Code of Practice for Suspended Ceilings 509 BS 8300 Design of Buildings and their approaches to meet needs of Disabled



Useful ReferencesPeople

510 BS 8500-1 Concrete - Complimentary British Standard to BS EN 206-1 - Method of specifying and guidance for specification'

511 BS 8500-2 Concrete - Complimentary British Standard to BS EN 206-1 - Specification for constituent materials and concrete

512 BS DD IEC TS 60695 Fire Hazard Testing – Part 7-3: Toxicity of Fire Effluent – Use and Interpretation of Test Results

513 BS EN 179 Building Hardware – Emergency Exit Device Operated by a Lever or Push Pad

514 BS EN 196 Method for testing concrete 515 BS EN 197-1 Cement, specification and conformity for common cements 516 BS EN 206 Concrete, specification, performance, production and compliance and

conformity 517 BS EN 274 Waste Fitting for Sanitary Appliances 518 BS EN 295 Vitrified Clay Pipes and Fittings 519 BS EN 329 Sanitary Tapware Waste Fittings for Showers 520 BS EN 403 Respiratory protective devices for self-rescue – Filtering devices with

hood for escape from fire – requirements, testing, marking 521 BS EN 411 Sanitary Tapware Waste Fittings for Sinks 522 BS EN 508 Roofing Products for Metal Sheet – Specification for Self Supporting

Products of Steel, Aluminium or Stainless Steel Sheet 523 BS EN 593 Specification for butterfly valves 524 BS EN 607 Eaves gutters and fittings made from PVC-U 525 BS EN 612 Eaves gutters and rainwater down pipes of metal sheet 526 BS EN 649 Resilient Floor Coverings – Homogeneous & Heterogeneous

Polyvinyl Chloride Floor Coverings 527 BS EN 654 Resilient Floor Coverings – Semi-flexible Polyvinyl Chloride Tiles 528 BS EN 764-1 Pressure Equipment Part 1: Terminology – pressure, temperature,

volume, nominal size 529 BS EN 806 Specification for Installation inside buildings conveying water for

human consumption 530 BS EN 837-1 Specification for bourdon tube pressure and vacuum gauges 531 BS EN 877 Cast Iron Pipes and Fittings, their joints and accessories for

Evacuation of Water from Buildings 532 BS EN 934 Admixtures for concrete 533 BS EN 997 WC Pans and WC Suites with Integral Traps 534 BS EN 998 Specification for Mortar for Masonry 535 BS EN 1008 Mixing water for concrete 536 BS EN 1011 Parts 1 & 2 Welding. Recommendations for welding of metallic

materials. 537 Part 1 General welding for arc welding 538 Part 2 Arc welding of ferritic steels 539 BS EN 1057 Copper and Copper Alloys – Seamless Round for Water and Gas in

Sanitary and Heating Applications 540 BS EN 1063 Glass in Buildings – Security Glazing – Testing and Classification of

Resistance against Bullet Attack 541 BS EN 1125 Building Hardware – Panic Exit Devices Operated by a Horizontal

Bar 542 BS EN 1154 Controlled Door Closing Devices 543 BS EN 1158 Building Hardware – Door Co-ordinator Devices



Useful References544 BS EN 1254 Copper and Copper Alloys – Plumbing Fittings or Capillary Brazing

to Copper Tubes, Manufacturers Association 545 BS EN 1303 Building Hardware – Cylinders for Locks 546 BS EN 1329 Plastic Piping Systems for Soil and Waste Discharge 547 BS EN 1451 Plastic Piping Systems for Soil and Waste Discharge within

Buildings 548 BS EN 1452 Plastic Piping Systems for Water Supply 549 BS EN 1455 Plastic Pipe Systems for Soil and Waste (Low and High

Temperature) Within Building – Acrylonitride Butadiene-Styrene 550 (APS) Specification for Pipes, Fittings and System 551 BS EN 1492-4 Textiles Slings – Safety Part 4: Lifting Slings for general service

made from natural and man made fibre ropes 552 BS EN 1514-7 Flanges and their joints – Gaskets for PN-designated flanges Part

7: covered metal jacketed gaskets for use with steel flanges 553 BS EN 1519 Plastic Piping Systems for Soil and Waste Discharge (Low and High

Temperature) Within Building Structure – 554 Polyethlene (PE) Specification for Pipes, Fittings and System 555 BS EN 1527 Building Hardware – Hardware for Sliding and Folding Doors 556 BS EN 1565 Plastic Piping System for Soil and Waste Discharge (Low and High

Temperature) Within Building. Styrene Copolymer 557 Blends (SAN + PVC) Specification for Pipes Fittings and System 558 BS EN 1566 Plastic Piping Systems for Soil and Waste (Low and High

Temperature) within Building Structure – Chlorinated Poly 559 (Vinyl Chloride) (PVC-c) Specification for Pipes, Fittings and System 560 BS EN 1670 Building Hardware – Corrosion Resistance 561 BS EN 1634 Fire Resistance Tests for Door and Shutter Assemblies, Fire Doors

and Shutters 562 BS EN 1906 Building Hardware – Lever Handles and Knob Furniture 563 BS EN 1935 Building Hardware – Single Axis Hinges 564 BS EN 1982 Specification for copper alloy ingots and copper alloy and high

conductivity copper castings 565 BS EN 10160 Ultrasonic testing of steel flat product of thickness equal to or

greater than 6mm(reflection method) 566 BS EN 10223 Specification for zinc-coated hexagonal steel wire netting 567 BS EN 12051 Building hardware – door and window bolts 568 BS EN 12056 Gravity drainage systems inside buildings 569 BS1184 Specification for copper and copper alloy traps 570 BS EN 12056 Part 3 Gravity drainage systems inside buildings – roof drainage

layout and calculation 571 BS EN 12350 Testing fresh concrete 572 BS EN 12350-2 Testing fresh concrete – slump test 573 BS EN 12390 Testing hardened concrete 574 BS EN 12390-3 Testing hardened concrete – strength of test specimens 575 BS EN 12445 Industrial, commercial & garage – doors and gates 576 BS EN 12620 Aggregates for concrete 577 BS EN 12635 Industrial, commercial and garage doors and gates – installation

and use 578 BS EN 12639 Liquid pumps and pump units – noise test code/grade 2 and grade 3

of accuracy 579 BS EN 12680-2 Founding. Ultrasonic examination of steel castings for highly



Useful Referencesstressed components

580 BS EN 12810-1 Façade scaffolds made of prefabricated components – part 1: products specifications

581 BS EN 12810-2 Façade scaffolds made of prefabricated components – part 2: particular methods of structural design

582 BS EN 12811-1 Temporary works equipment – part 1: scaffolds – performance requirements and general design

583 BS EN 12825 Raised access floors 584 BS EN 12952 Water-tube boilers 585 BS EN 13024 Glass in building – thermally toughened borosilicate safety glass 586 BS EN 13124 Windows, doors and shutters explosion resistant 587 BS EN 13139 Aggregate for mortar 588 BS EN 13162 Thermal insulation products for buildings – factory made mineral

wool 589 BS EN 13163 Thermal insulation products for buildings – factory made products

of expanded polystryrene 590 BS EN 13164 Thermal Insulation products for buildings – factory made products

of extruded polystyrene 591 BS EN 13310 Kitchen Sinks 592 BS EN 13553 Resilient floor coverings – polyvinyl chloride floor covering for

use in special wet areas 593 BS EN 13586 Cranes - access 594 BS EN 13813 Screed material and floor screeds 595 BS EN 13892-3 Methods of test for screed materials part 3: determination of wear

resistance 596 BS EN 14329 Inland navigation vessels – installation of berths and loading areas 597 BS EN 50054 Electrical apparatus for detection of combustible gases, general

required test methods 598 BS EN 50055 Electrical apparatus for detection of combustible gases,

performance requirements for group I apparatus indicating up to 5% (V/V) methane in air.

599 BS EN 50056 Electrical apparatus for detection of combustible gases, performance requirements for group I apparatus indicating up to 100% (V/V) methane in air.

600 BS EN 50174 Part 2 Information technology – cable installation – installation planning and practices inside buildings

601 BS EN 55022 Radio disturbance characteristics information technology equipment

602 BS EN 60076-10 Determination of transformer and reactor sound levels 603 BS EN 60534-8 Industrial - process control valves part 8: noise considerations 604 BS EN 60651 Specification for sound level meters 605 BS EN 60849 Sound systems for emergency purposes 606 BS EN 60947 Specification for degrees of protection of enclosures of switchgear

and control-gear for voltages up to 1000V AC and 1200V DC 607 BS EN 61000 Electromagnetic compatibility (EMC) 608 BS EN 61496-1 Safety of machinery – electro-sensitive protective equipment –

part 1: general requirements and tests 609 BS EN ISO 1461 Hot dip galvanised coatings on fabricated iron and steel articles

– Specifications and test methods 610 BS EN ISO 4126-1 Safety devices for protection against excessive pressure – part



Useful References1: safety valves

611 BS EN ISO 5667-19 Water Quality – sampling – part 19: guidance on sampling in marine sediments

612 BS EN ISO 9000 Quality management systems – fundamentals and vocabulary 613 BS EN ISO 9001 Quality management systems - requirements 614 BS EN ISO 9002 Quality assurance 615 BS EN ISO 10204 Metallic products – types of inspection documents 616 BS EN ISO 14692 Parts 1-4 Petroleum and natural gas industries – glass

reinforced plastics (GRP) piping 617 BS EN ISO 15465 Pipework – Strip wound metal hoses and hose assemblies 618 BS EN ISO 15614-1 Specification and qualification of welding procedures for

metallic materials – welding procedure test part 1: arc and gas welding of steels and arc welding of nickel and nickel alloys

619 BS ISO 4308 Cranes and lifting appliances-Selection of wire ropes 620 BS ISO 15175 Soil quality – characterization of soil related to ground water

protection 621 BS PD 5304 Safe use of machinery 622 CEB-FIP Model code for concrete structures 623 CEMA 300 Screw conveyor dimensional standards 624 CEMA 350 Screw conveyors 625 CEN EN 1822-1 High efficiency air filters (HEPA & ULPA) 626 CGA/GAS 02-DIR directory of cleaning agents for oxygen service 627 CICIND Manual for inspection and maintenance of brickwork and concrete

chimneys 628 CICIND Model code for steel chimneys 629 CINI Handbook for insulation - issued by: commission of dutch insulation

industrie, ceintuurbaan 182, 1403 ak, bussum, netherlands 630 CONCAWE No. 2/79 Method for determining sound power levels of flares used

in refineries, chemical plants and oilfields 631 CONCAWE No. 3/77 Test method for measurement of noise emitted by furnaces

for use in petroleum and petrochemical industry 632 CONCAWE Report 87/59 predictions of noise radiated from pipe systems, an

engineering procedure for plant design. 633 CSA 22.2 – 157 Intrinsincally safe and non-incendive equipment for use in

hazardous locations 634 CSA 22.2 – 30 Explosion-proof enclosures for use in Class 1 hazardous locations

general instruction No 1-2R 635 DIN 0875 Radio interference suppression of electrical appliances and systems 636 DIN 3852 Part 2 Stud-ends and tapped holes with pipe thread for use with

compression couplings 637 DIN 4030 Evaluation of liquids, soils and gases aggressive to concrete 638 DIN 19234 Measurement and control; electrical distance sensors; DC interface for

distance sensor and signal converter 639 DIN 45635-22 Measurement of airborne noise emitted by machines; enveloping

surface method, flares 640 DIN 45635-47 Measurement of noise emitted by machines: Airborne noise

emission enveloping surface method chimneys 641 DIN 45681 Detection of tonal components of noise and determination of a tone

adjustment for assessment of noise emissions 642 DIN 50129 Testing of metallic materials, testing of welding filler materials for



Useful Referencesliability to cracking

643 DIN EN 1870-12 Safety of woodworking machines – circular sawing machines – part 12. pendulum cross-cut sawing machines EURO 123.30

644 DIN EN 10204 Inspection documents for delivery of metallic products 645 DIN EN 50277 Measurement and control, electrical distance sensors, DC

interface for distance sensor and signal converter 646 DIN EN ISO 15607 Specification and qualification of welding procedures for

metallic materials – general rules supercedes DIN EN 288-1 Edn. EURO 94.70 647 DIN RP-B401 Cathodic protection design 648 DIN V 19250 Control technology; fundamental safety aspects to be considered

for measurement and control equipment 649 DIN VDE 0801 Principle for computers in safety related systems 650 DIN VDE 0101 Erection of power installations with rated voltages exceeding 1

kV 651 EEMUA Pub. 106 General specification for silencers and acoustic enclosures 652 (Formerly OCMA NWG-4, 1979), replaced by EEMUA Pub. 161 653 EEMUA Pub. 132 Specification of 3 phase cage induction motors 654 EEMUA Pub. 140 Noise procedure specification (Formerly OCMA NWG-1, Rev.

2, 1980) 655 EEMUA Pub. 142 Acoustic insulation of pipes, valves and flanges (formerly

OCMA NWG-5, 1982) 656 EEMUA Pub. 143 Recommendations for tube-end welding, tubular heat transfer

equipment. (Formerly OCMA specification No. TEW 1) 657 EEMUA Pub. 161 Guide to selection and assessment of silencers and acoustic

enclosures 658 EEMUA Pub. 201 Process plant control desks utilising human-computer

interfaces – a guide to design, operational and human interface issues659 EIA RS 232,422 & 485 Interface between data terminal equipment and data

communication equipment employing serial binary data 660 EIA/TIA 222 Structural standards for steel antenna towers and antenna supporting

structures 661 EIA/TIA 232 Interface between data terminal equipment and data communication

equipment 662 EIA/TIA 422 Electrical characteristics of balanced voltage digital interface

circuits 663 EIA/TIA 423 Electrical characteristics of unbalanced voltage digital interface

circuits 664 EIA/TIA 455 Standard test procedures for fibre optic fibres, cables, transducers,

connecting and terminating devices 665 EIA/TIA 568 Commercial building telecommunications cabling standard 666 EIA/TIA 569 Commercial building standard for telecommunications pathways

and spaces 667 EIA/TIA 606 Administration standard for telecommunications infrastructure of

commercial buildings 668 EJMA Standards of expansion joint manufacturers association 669 EN 54 Fire protection and fire alarm system 670 EN 81 Safety rules for construction and installation of lifts and service lifts 671 EN 287 Approval testing of welders for fusion welding 672 EN 288 Approval of welding procedures for metallic materials 673 EN 292 Safety of machinery - basic concepts, general principles for design



Useful References674 EN 294 Safety of machinery - safety distances to prevent danger zones to be

reached by upper limbs 675 EN 349 Safety of machinery - minimum gaps to avoid crushing parts of human

body 676 EN 563 Safety of machinery - temperature of touchable surfaces - ergonomics

data to establish temperature limit values for hot surfaces 677 EN 571 Part 1 Non destructive testing – penetrant testing part 1: general

principles 678 EN 614 Safety of machinery - ergonomic design principles 679 EN 837 -1 Pressure Gauges, Part 1: Bourdon tube pressure gauges. dimensions,

metrology, requirements and testing 680 EN 1043-1 Destructive tests on welds in metallic materials. Hardness testing.

Hardness test on arc welded joints 681 EN 1418 Welding personnel. Approval testing of welding operators for fusion

welding and resistance weld setters for fully mechanized and automatic welding of metallic materials

682 EN 1964 Transportable gas cylinders - specification for design and construction of refillable transportable seamless steel gas cylinders of water capacities from 0,5 litre up to and including 150 litres

683 EN 10028 Flat products made of steel for pressure purposes 684 EN 10164 Steel products with improved deformation properties perpendicular to

surface of product; technical delivery conditions 685 EN 10204 Metallic products - Type of inspection documents 686 EN 41003 Particular safety requirements for equipment to be connected to

telecommunications networks 687 EN 50014 Electrical apparatus for potentially explosive atmospheres - general

requirements 688 EN 50015 Electrical apparatus for potentially explosive atmospheres - oil

immersion 689 EN 50016 Electrical apparatus for potentially explosive atmospheres - pressurized

apparatus 690 EN 50017 Electrical apparatus for potentially explosive atmospheres - powder

filling 691 EN 50018 Electrical apparatus for potentially explosive atmospheres - flameproof

enclosure 692 EN 50019 Electrical apparatus for potentially explosive atmospheres - increased

safety 693 EN 50020 Electrical apparatus for potentially explosive atmospheres - intrinsic

safety 694 EN 50021 Type of protection ‘n’ 695 EN 50028 Electrical apparatus for potentially explosive atmospheres -

encapsulation 'm' 696 EN 50039 Electrical apparatus for potentially explosive atmospheres –

intrinsically safe electrical systems ‘I’ 697 EN 50057 Electrical apparatus for detection and measurement of combustible

gases; performance requirements for group II apparatus indicating up to 100% lower explosive limit

698 EN 50058 Electrical apparatus for detection and measurement of combustible gases; performance requirements for group II apparatus indicating up to 100% (v/v) gas

699 EN 50081 Electromagnetic compatibility - generic emission standard



Useful References700 EN 50082 Electromagnetic compatibility - generic immunity standard 701 EN 50091-2 Uninterruptible power systems (UPS) 702 EN 50160 Voltage characteristics of electricity supplied by public distribution

systems 703 EN 50174 Information technology cable installation 704 EN 50209 1999 Test of Insulation of bars and coils of high-voltage machines

supersedes BS 4999-144; 1987 (F) 705 EN 55011 Limits and methods of measurement of radio interference

characteristics of industrial, scientific and medical (ISM) radiofrequency equipment 706 EN 55011M Limits and methods of measurement of radio disturbance

characteristics of industrial, scientific and medical radio frequency equipment 707 EN 55022 Limits and methods of measurement of radio interference

characteristics of information technology (ITE) equipment 708 EN 61000-4-5 Electromagnetic compatibility (EMC) Part 4: testing and

measurement techniques – section 5: surge immunity test 709 EN 61779 Parts 1 to 5 Electrical apparatus for detection and measurement of

flammable gases. Part 1: General requirements and test methods 710 Part 2: Performance requirements for group I apparatus indicating a volume

fraction up to 5 % methane in air 711 Part 3: Performance requirements for group I apparatus indicating a volume

fraction up to 100 % methane in air 712 Part 4: Performance requirements for group II apparatus indicating a volume

fraction up to 100 % lower explosive limit 713 Part 5: Performance requirements for group II apparatus indicating a volume

fraction up to 100 % gas 714 EN 187101 Optical telecommunications cables to be used in ducts or direct buried

application 715 ERA 69-30 Current rating standards for distribution cables 716 FM 3610 Intrinsically safe apparatus and associated apparatus for us n class 1, 11

& 111, division 1, and class 1, zone 0 & 1 717 Hazardous (classified) locations 718 FM 3615 Explosion-proof electrical equipment – general requirements 719 FIP Guide to good practice grouting of tendons in pre stressed concrete 720 FIP Recommendations for acceptance of post-tensioning systems 721 HEI Steam surface condensers and addendum 1 steam jet vacuum systems 722 HTFS Handbook sheet JMI allowing for fouling in heat exchanger design 723 ICAO Annex 14 regulations 724 ICAO July 1990 Annex 14 to Convention on international civil aviation

aerodromes 725 IEC 34-9 Rotating electrical machines – Part 9: noise limits 726 IEC 225 Specification for octave-band and fractional-octave-band-analogue and

digital filters 727 IEC 651 Recommendations for sound level meters 728 IEC 60034 Rotating electrical machines 729 IEC 60038 IEC standard voltages 730 IEC 60044 Current Transformers 731 IEC 60044-1 Current Transformers 732 IEC 60044-2 Voltage Transformers 733 IEC 60050 International electrotechnical vocabulary - electrical installations of

buildings



Useful References734 IEC 60051 Direct acting indicating analogue electrical measuring instruments and

their accessories 735 IEC 60056 High voltage alternating-current circuit-breakers 736 IEC 60060 High voltage test techniques 737 IEC 60068 Environmental testing 738 IEC 60071 Insulation coordination 739 IEC 60072 Dimensions and output ratings for rotating electrical machines 740 IEC 60073 Basic and safety principles for man-machine interface, marking and

identification, indicating devices and actuators 741 IEC 60076 Power transformers 742 IEC 60079 Electrical apparatus for explosive gas atmospheres 743 IEC 60085 Method for determining thermal classification of Electrical Insulation 744 IEC 60096 Radio frequency cables 745 IEC 60099-1 Lightning arresters part 1 – non linear resistor type arrestor for a.c

systems 746 IEC 60112 Method for determining comparative and proof-tracking indices of

solid insulating material under moist conditions 747 IEC 60113 Diagrams, charts, tables 748 IEC 60120 Dimensions of ball and socket couplings of string insulator units 749 IEC 60137 Bushing for alternating voltages above 1000V 750 IEC 60146 Semiconductor converters 751 IEC 60156 Method for determination of electric strength of insulating oils 752 IEC 60157 Low voltage switchgear and control gear 753 IEC 60158 Specification for control gear for voltages up to and including

1000VAC &1200VDC 754 IEC 60168 Tests on indoor and outdoor post insulators of ceramic material or

glass for systems with nominal voltages greater that 1000V 755 IEC 60204 Electrical equipment of industrial machines 756 IEC 60214 On-load tap-changers 757 IEC 60225 Octave, half-octave and third-octave band filters intended for analysis

of sound and vibrations, replaced by IEC 61265 758 IEC 60227 Polyvinyl chloride insulated cables of rate voltages up to including

450/750 V 759 IEC 60255 Electrical relays 760 IEC 60265 High-voltage switches 761 IEC 60269 Low voltage fuses 762 IEC 60282 High voltage fuses 763 IEC 60289 Reactors 764 IEC 60296 Specification for unused mineral oils for transformers and switchgear 765 IEC 60292 Low voltage motor starters 766 IEC 60298 AC metal-enclosed switchgear and control-gear for rated voltages

above 1kV and up to and including 52kV 767 IEC 60300 Reliability and maintainability management 768 IEC 60304 Standard colours for insulation for low-frequency cables and wires 769 IEC 60309 Plugs, socket-outlets and couplers for industrial purposes 770 IEC 60317 Specifications for particular types of winding wires; 771 IEC 60331 Fire resisting characteristics of electric cable 772 IEC 60332 Tests on electric cables under fire conditions 773 IEC 60364 Electrical installation of buildings 774 IEC 60383 Tests on insulators of ceramic material or glass for overhead lines with



Useful Referencesa nominal voltage greater than 1000 V

775 IEC 60398 General test conditions for industrial electroheating equipment 776 IEC 60408 Low voltage air-break switches, air-break de-connectors, air-break

switches, de-connectors and fuse-combination units 777 IEC 60422 Maintenance and supervision guide for insulating oils in service 778 IEC 60433 Characteristics of string insulator units of long rod type 779 IEC 60439 Low voltage switchgear and control gear assemblies 780 IEC 60445 Identification of apparatus terminals and general rules for a uniform

system of terminal marking, using an alpha-numeric notation 781 IEC 60470 High voltage A.C contactors 782 IEC 60473 Dimensions for panel mounted indicating and recording electrical

measuring instruments 783 IEC 60478 Stabilized power supplies, DC output 784 IEC 60493-1-1992 Low voltage switchgear and control gear assemblies, part 1:

type tested and partially type tested assemblies 785 IEC 60521 Class 0.5, 1 & 2 alternating current watt hour meters 786 IEC 60529 Electrical apparatus ingress protection 787 IEC 60534 Industrial process control valves – part 8 noise considerations 788 IEC 60542 Application guide for on load tap changers 789 IEC 60549 High voltage fuses for external protection of shunt power capacitors 790 IEC 60551 Determination of transformer and reactor sound levels 791 IEC 60584 Thermocouples 792 IEC 60593 Internal fuses and internal overpressure disconnectors for shunt

capacitors 793 IEC 60605 Equipment reliability testing 794 IEC 60617 Graphical symbols for diagrams 795 IEC 60623 Vented nickel-cadmium prismatic rechargeable single cells 796 IEC 60654 Operating conditions for industrial-process measurement and control

equipment 797 IEC 60688 Electrical measuring transducers for converting a.c electrical

quantities to analogue or digital signals 798 IEC 60694 Common specifications for high voltage switchgear and control gear

standards 799 IEC 60695 Fire hazard testing –part 7-1: toxicity of fire effluent – general

guidance 800 IEC 60721-2-1 Classification of environmental conditions 801 IEC 60726 Dry-type power transformers 802 IEC 60742 Isolating transformers and safety isolating transformers 803 IEC 60751 Industrial platinum resistance thermometer sensors 804 IEC 60794 Optical fibre cables 805 IEC 60801 Electromagnetic compatibility for industrial process measurement and

control equipment 806 IEC 60815 Guide for selection of insulators in respect of polluted conditions 807 IEC 60831 Shunt power capacitors of self-heating type for a.c systems having a

rated voltage up to and including 1kV 808 IEC 60849 Sound systems for emergency purposes 809 IEC 60851 Winding wires – test methods 810 IEC 60871 Shunt capacitors for A.C power systems having a rated voltage above

1kV 811 IEC 60894 Guide for test procedure for measurement of loss tangent on coils and



Useful Referencesbars for machine windings

812 IEC 60896 Stationary lead-acid batteries, general requirements and methods of test

813 IEC 60898 Electrical accessories - Circuit-breakers for overcurrent protection for household and similar installations

814 IEC 60902 Industrial process measurement and control terms and definitions 815 IEC 60905 Loading guide for dry-type power transformers 816 IEC 60909 Short-circuit calculation in three-phase AC systems 817 IEC 60947 Low voltage switchgear and control gear 818 IEC 61000 Electromagnetic compatibility (EMC) 819 IEC 61024 Protection of structures against lightning 820 IEC 61078 Analysis techniques for dependability – reliability block diagram

method 821 IEC 61089 Round wire concentric lay overhead electrical stranded conductors 822 IEC 61099 Specification for unused synthetic organic esters for electrical

purposes 823 IEC 61131 Programmable controllers 824 IEC 61241 Electrical apparatus for use in presence of combustible dust 825 IEC 61285 Industrial-process control - safety of analyser houses 826 IEC 61293 Marking of electrical equipment with ratings related to electrical

supply - safety requirements 827 IEC 61481 Live Working – portable phase comparators for use on voltages from

1KV to 36 KV A.C 828 IEC 61508 Functional safety of electrical/electronic/programmable electronic

safety related systems 829 IEC 61511 Functional safety: safety instrumented systems for process industry

sector 830 IEC 61518 Mating dimensions between differential pressure (type) measuring

instruments and flanged-on shut-off devices up to 413 bar 831 IEC 61634 High voltage switchgear and control gear - Use and handling of

sulphur hexafluoride (SF6) in high voltage and control gear 832 IEC 61641 Guide for testing under conditions of arcing due to internal fault 833 IEC 61850 Communications networks and systems in substations 834 IEC 62086-1IEC 62086-1 Electrical apparatus for explosive gas atmospheres 835 IEC/CISPR 11 Limits and methods of measurement of radio disturbance

characteristics of industrial, scientific and medical (ISM) radiofrequency equipment 836 IEC/CISPR 14 Limits and methods of measurement of radio disturbance

characteristics of electric motor-operated and thermal appliances 837 for household and similar purposes, electric tools and similar electric apparatus 838 IEC/CISPR 22 Limits and methods of measurement of radio interference

characteristics of information technology (ITE) equipment 839 IEEE 80 Guide for safety in AC substation grounding 840 IEEE 115 Guide: Test procedures for synchronous machines 841 IEEE 421.2 Guide for identification, testing, and evaluation of dynamic

performance of excitation control systems 842 IEEE 421.5 Recommended practice for excitation system models for power

system stability studies 843 IEEE 519 Recommended practices and requirements for harmonic control in

electrical power systems 844 IEEE 802 Standards for local and metropolitan area networks



Useful References845 IGC 33/97/E Cleaning of equipment for oxygen service (EIGA – european

industrial gases association) 846 IP Code Part 2 Design, construction and operation of distribution installations 847 IP Code Part 7 Petroleum measurement manual - density, continuous density

measurement 848 IP Code Part 9 Liquefied petroleum gas, Vol I large bulk pressure storage and

refrigerated LPG 849 IP Code Part 13 Petroleum measurement manual - fidelity and security of

measurement data transmission systems, electric and/or electronic pulsed data cabled transmission for fluid metering systems

850 IP Code Part 15 Area classification code for installations, handling flammable fluids

851 ISA 5.1 Instrument symbols and identification 852 ISA 5.2 Binary logic diagrams for process operation 853 ISA 5.3 Graphic symbols for distributed control shared display instrumentation,

logic and computer systems 854 ISA 18.1 Annunciator sequences and specifications 855 ISA 55.1 Hardware testing of digital process computers (codes of BS-588 practice

for testing computer based systems) 856 ISBN 92-67-10188-9 ISO guide to expression of uncertainty in measurement

1995 857 ISGOTT International safety guide for oil tankers and terminals 858 ISO 15 Rolling bearings – radial bearings – boundary dimensions 859 ISO 31 Quantities and units 860 ISO 281 Rolling bearings – dynamic load ratings and rating life 861 ISO 636 Welding consumables – rods, wires and deposits for tungsten inert gas

welding of non-alloy and fine-grain steels – classification 862 ISO 888 Bolts, screws and studs: nominal lengths and thread length for general

bolts 863 ISO 898-1 Mechanical properties of fasteners made of carbon steel and alloy steel

– part 1: bolts, screws and studs 864 ISO 1000 SI units and recommendations for use of their multiples and of certain

other units 865 ISO 1101 Technical drawings; Geometric tolerancing, tolerancing form,

orientation, location and run out; Generalities, definitions, symbols, indications on drawings

866 ISO 1109 Refractory products -- classification of dense shaped refractory products

867 ISO 1132 Rolling bearings – tolerances - definitions 868 ISO 1461 Metallic coatings: hot-dip galvanised coatings on fabricated ferrous

products: requirements. 869 ISO 1461 Galvanised coatings on fabricated iron and steel articles 870 ISO 1680-Parts 1 & 2 acoustics – test code for measurement of airborne noise

emitted by rotating electrical machinery 871 ISO 1813 Belt-drives – v–ribbed belts, joined v-belts including wide section belts

and hexagonal belts – eletrica conductivity of antistatic endless v-belts – electrical conductivity – characteristics and methods of test

872 ISO 1927 Prepared unshaped refractory materials (dense and insulating) -- classification

873 ISO 1940 Mechanical balancing of rotating bodies



Useful References874 Part 1 - Mechanical vibration – balance quality requirements of rigid rotors 875 ISO 1996 Part 1 Acoustics – description, assessment and measurement of

environmental noise 876 ISO 2063 Metallic and other coatings thermal spraying zinc aluminium and their

alloys 877 ISO 2186 Fluid flow in closed conduits – connections for pressure signal

transmissions between primary and secondary elements. 878 ISO 2204 Acoustics – Guide to international standards on measurement of air-

borne acoustical noise and evaluating its effects on human beings 879 ISO 2245 Shaped insulating refractory products -- classification 880 ISO 2314 Gas turbines - acceptance tests 881 ISO 2372 Mechanical vibration of machines with operating speeds from 0-200 r/s

– basis for specifying evaluation standards 882 ISO 2409 Paints and varnishes - cross cut test for adhesion 883 ISO 2548 Acceptance tests for centrifugal, mixed flow and axial pumps 884 ISO 2715 Liquid hydrocarbons, volumetric measurements by turbine meter

systems 885 ISO 2808 Paints and varnishes - determination of film thickness 886 ISO 2954 Mechanical vibration of rotating and reciprocating machinery 887 ISO 3046 parts I to VI Reciprocating, internal combustion engines 888 ISO 3170 Petroleum liquids – manual sampling 889 ISO 3171 Petroleum liquids – automatic pipeline sampling 890 ISO 3183 Petroleum and natural gas industries -- steel pipe for pipelines --

technical delivery conditions 891 Part 1: Pipes of requirement class A 892 Part 3: Pipes of requirement class C 893 ISO 3511 Process measurement control functions and instrumentation - symbolic

representation 894 ISO 3549 Zinc dust pigments for paint – specifications and test methods 895 ISO 3582 Cellular plastics and cellular rubber, laboratory assessment of

horizontal burning characteristics of small specimens subjected to a small flame 896 ISO 3601 Part 1 Fluid systems sealing devices – O rings 897 Part 1: Inside diameters, tolerances and size identification code 898 ISO 3690 Welding and allied processes – determination of hydrogen content in

ferritic steel arc weld metal 899 ISO 3743 Acoustics - Determination of sound power levels of noise sources -

engineering methods for special reverberation test rooms 900 ISO 3744 Acoustics – Determination of sound power levels of noise sources

using sound pressure – Engineering method in an essentially free field over a reflecting surface

901 ISO 3746 Acoustics – determination of sound power levels of noise sources using sound pressure. Survey method using an enveloping measurement surface of a reflecting plan

902 ISO 4021 Hydraulic fluid power - particulate contamination analysis - extraction of fluid samples from lines of an operating system

903 ISO 4032 Hexagon nuts style 1: products grade A & B 904 ISO 4200 Plain end steel tubes, welded and seamless - general tables of

dimensions and masses per unit length 905 ISO 4406 Hydraulic fluid power - fluids - method for coding level of

contamination by solid particles



Useful References906 ISO 4624 Paints and varnishes-pull off test for adhesion 907 ISO 4628 Paints and varnishes - evaluation of degradation of paint coatings -

designation of intensity, quantity and size of common types of defects 908 ISO 5024 Petroleum liquids and gases -measurement - standard reference

conditions 909 ISO 5167 Measurement of fluid by means of orifice plates, nozzles and venturi

tubes inserted in circular cross-section conduits running full 910 ISO 5199 Industrial pumps – technical specification for centrifugal and rotary

pumps 911 ISO 5211 Part-turn valve actuator attachment 912 ISO 5752 Metal valves for use in flanged pipe systems – face-to-face and centre-

to-face dimensions 913 ISO 6141 Gas analysis - calibration gas mixtures - certificate of mixture

preparation. 914 ISO 6142 Gas analysis - preparation of calibration gas mixtures - weighing

methods 915 ISO 6143 Gas analysis - determination of composition of calibration gas mixtures

– comparison methods 916 ISO 6326 Part 1 Natural gas – determination of sulphur compounds – part 1:

general introduction 917 ISO 6327 Gas analysis - determination of water dew point of natural gas - cooled

surface condensation hygrometers 918 ISO 6385 Ergonomic principles in design of work systems 919 ISO 6570 Parts 1, 2 & 3 Natural gas – determination of potential hydrocarbon-

liquid content Part 1: Principles and general requirements 920 Part 2: Weighing method 921 Part 3: Volumetric method 922 ISO 6974 Natural gas – Determination of hydrogen inert gases and hydrocarbons

up to C8 - gas chromatographic method 923 ISO 6975 Natural gas – extended analysis – gas chromatographic method 924 ISO 6976 Natural gas – calculation of calorific values, density, relative density

and wobbe index from composition 925 ISO 6978 Natural gas – Determination of mercury 926 ISO 7235 Acoustics – measurement procedures for ducted silencers – insertion

loss, flow noise and total pressure loss 927 ISO 7411 Hexagon headed bolts – product grade A & B 928 ISO 7415 Plain washers for high strength structural bolting, hardened and

tempered 929 ISO 7730 Determination of PMV and PPD indices and specifications of

conditions for thermal comfort 930 ISO 7731 Ergonomics – danger signals for public and work areas – auditory

danger signals 931 ISO 8297 Acoustics - determination of sound power levels of multisource

industrial plants for evaluation of sound pressure levels in environment 932 ISO 8501 Preparation of steel substrates before application of paints and related

products - Visual assessment of surface cleanliness 933 ISO 8502 Preparation of steel substrates before application of paints and related

products - tests for assessment of surface cleanliness 934 ISO 8503 Preparation of steel substrates before application of paints and related

products - surface roughness characteristics of blast cleaned steel substrates



Useful References935 ISO 8504 Preparation of steel substrates before application of paints and related

products - surface preparation methods 936 ISO 8995 Principles of visual ergonomics –lighting of indoor work systems 937 ISO 9002 Quality systems – model for quality assurance in production,

installation and servicing 938 ISO 9606 Approval testing of welders. fusion welding 939 ISO 9613 Part 1 Acoustics – attenuation of sound during propagation outdoors” –

part 1 calculation of absorption of sound by atmosphere 940 ISO 9613 Part 2 Acoustics – attenuation of sound during propagation outdoors” -

part 2 general method of calculation 941 ISO 9614 Part 1 Acoustics – determination of sound power levels of noise sources

using sound intensity. part 1 – measurement at discrete points 942 ISO 9614 Part 2 Acoustics – determination of sound power levels of noise sources

using sound intensity. part 2 – measurement by scanning 943 ISO 9951 Measurement of gas flow in closed conduits – turbine meters 944 ISO 10012 Quality assurance requirements for measuring equipment 945 ISO 10081 Classification of dense shaped refractory products 946 ISO 10101 Parts 1, 2 & 3 Natural gas–determination of water by karl fischer

method 947 Part 1: Introduction 948 Part 2: Titration procedure 949 Part 3: Coulometric procedure 950 ISO 10303 Standard for exchange of product data (STEP) 951 ISO 10441 Petroleum and natural gas industries – flexible couplings for

mechanical power transmission – special purpose applications 952 ISO 10474 Steel and steel products - inspection documents 953 ISO 10494 Gas Turbines and gas turbine sets – measurement of emitted airborne

noise – engineering/survey method 954 ISO 10715 Natural gas–sampling guidelines 955 ISO 10723 Natural gas–Performance evaluation for on-line analytical systems 956 ISO 10816 Mechanical vibration – evaluation of machine vibration by

measurements on non-rotating parts 957 ISO 11014 Safety data sheet for chemical products - content and order of

selection 958 ISO 11064 -2 Ergonomic design of control centres – part 2: principles for

arrangement of control suites 959 ISO 11124 Preparation of steel substrates before application of paints and related

products. Specifications for metallic blast-cleaning abrasives 960 ISO 11126 Preparation of steel substrates before application of paints and related

products. Specifications for non-metallic blastcleaning abrasives 961 ISO 11127 Preparation of steel substrates before application of paints and related

products. Test methods for non-metallic blastcleaning abrasives 962 ISO 11546 Part 2 Sound Insulation Performance of Enclosures – measurement in-

situ 963 ISO 11691 Acoustics – Measurement of insertion loss of ducted silencers without

flow – laboratory survey method 964 ISO 12213 Parts 2 & 3 Natural gas – calculation of compression factor – 965 Part 2: Calculation using molar–composition analysis 966 Part 3: Calculation using physical properties 967 ISO 12944 Paints and varnishes. Corrosion protection of steel structures by



Useful Referencesprotective paint systems.

968 ISO 13443 Natural gas–standard reference conditions 969 ISO 13686 Natural gas–quality designation 970 ISO 13691 Petroleum and natural gas Industries – high speed special purpose gear

units 971 ISO 13704(API 530) Calculation of heater tube thicknesses in petroleum

refineries 972 ISO 13705 Fired Heaters - general refinery service 973 ISO 13706 Air-cooled heat exchangers for general refinery services 974 ISO 13709 Centrifugal pumps for petroleum, petrochemical and natural gas

industries 975 ISO 14001 Environmental management systems - specification with guidance for

use 976 ISO 14313 Petroleum and natural gas industries – pipeline transportation systems

– pipeline valves 977 ISO 14691 Petroleum and natural gas Industries – flexible couplings for

mechanical power transmission – general purpose applications 978 ISO 15156 Petroleum and natural gas industries -- materials for use in H2S-

containing environments in oil and gas production, petroleum and natural gas Industries part 1: general principles for selection of cracking-resistant materials - part 2:

979 cracking-resistant carbon and low alloy steels, and use of cast irons - part 3: cracking-resistant CRAs (corrosionresistant alloys) and other alloys

980 ISO 15175 Soil Quality – characterization of soil related to ground water protection

981 ISO 15607 Specification and qualification of welding procedures for metallic materials – general rules

982 ISO 15613 Specification and qualification of welding procedures for metallic materials – qualification based on pre-production welding test

983 ISO 15614-1 Specification and qualification of welding procedures for metallic materials – welding procedure test –

984 Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys 985 ISO 17846 Welding and allied processes – health & safety – wordless

precautionary labels for equipment and consumables used in arc welding and cutting 986 ISO 19011 Guidelines for quality and/or environmental management systems

auditing 987 ISO/DIS 9241 Ergonomic requirement for office work with visual display

terminals (VDT's) 988 ISO/DIS 9857 Petroleum and liquid petroleum products - continuous density

measurement 989 ISO/DIS 11429 Safety of machinery – system of auditory and visual danger and

information signals 990 ISO/DIS 11064 Ergonomic design of control centres 991 ISO/DIS 14532 Natural gas – Terminology 992 ISO EN 10168 Steel Products – Inspection Documents – List of Information and

Description 993 ISO/IEC 3352 Acoustics – assessment of noise with respect to intelligibility of

speech 994 ISO/IEC 11801 Generic cabling system for customer premises 995 ISO TR 5168 Measurement of fluid flow – Evaluation of uncertainties 996 ISO/TR 7849 Estimation of airborne noise emitted by machinery using vibration



Useful Referencesmeasurement

997 ISO/TR 10465 Parts 1-3 Underground installation of flexible glass-reinforced thermosetting resins (GRP) Pipes

998 ISO/TR 12765 Measurement of fluid flow in closed conduits - Methods using transit-time ultrasonic flow meters

999 ISO/TR 15608 Welding – Guidelines for a metallic material grouping system 1000 ISO/TR 17671-5 Welding – Recommendations for welding of metallic materials

– part 5: welding of clad steels 1001 ISO/TR 17671-7 Welding – Recommendations for welding of metallic materials

– part 7: electron beam welding 1002 ISO/TR 18569 Safety of Machinery – Guidelines for understanding and use of

safety of machinery standards 1003 ISSMFE Report of sub-committee on standardisation of penetration testing in

europe 1004 ITU-T G.175 Transmission planning for private/public network interconnection

of voice traffic 1005 ITU-T G.611 Characteristic of symmetric cable pairs for analogue transmission 1006 ITU-T G.621 Characteristic of 0.7/2.9 mm coaxil pairs 1007 ITU-T G.651 Characteristic of 50/125 micrometre multimode graded index

optical fibre cable 1008 ITU-T G.652 Characteristic of a single mode optical fibre cable 1009 ITU-T K.8 Separation in soil between telecommunications cables and earthing

system of power facilities 1010 ITU-T K.11 Principles of protection against over voltages and over currents 1011 ITU-T K.12 Characteristics of gas discharge tubes for protection of

telecommunications installations 1012 ITU-T K.19 Joint use of trenches and tunnels for telecommunication and power

cables 1013 ITU-T K.20 Resistibility of telecommunications switching equipment to over

voltages and over currents 1014 ITU-T K.21 Resistibility of subscriber’s terminal to over voltages and over

currents 1015 ITU-T K.25 Protection of optical fibre cables 1016 ITU-T K.34 Classification of electromagnetic environmental conditions for

telecommunication equipment: basic EMC requirements 1017 ITU-T K.51 Safety criteria for telecommunication equipment 1018 ITU-T L.3 Armouring of cables 1019 ITU-T L.10 Optical fibre cables for duct, tunnel, aerial and buried application 1020 ITU-T L.12 Optical fibre joints 1021 ITU-T L.13 Sheath joints and organisers of optical fibre cable in outside plant 1022 ITU-T L.14 Measurement method to determine tensile performance of optical

fibre cables under load 1023 ITU-T L.36 Single mode optical fibre connectors 1024 ITU-T P.54 Sound level meters 1025 ITU-T T.6 Facsimile coding schemes and coding control functions for Group 4

facsimile apparatus 1026 MIL-A-18001K Anodes, sacrificial zinc alloy 1027 MIL-HDBK-217 U.S. Military handbook: reliability prediction of electronic

equipment 1028 MSS SP 44 Steel pipe line flanges



Useful References1029 MSS SP 58 Pipe hangers and supports - materials, design and manufacture 1030 MSS SP 69 Pipe hangers and supports - selection and application 1031 MSS SP 75 Specification for high test wrought butt welding fittings 1032 MSS SP 97 Integrally reinforced forged carbon steel - branch o/let fitting 1033 NACE MR 0103 Materials resistant to sulfide stress cracking in corrosive

petroleum refining environments 1034 NACE MR 0175 Replaced by ISO 15156 1035 NACE RP 0177 Mitigation of alternating current and lightning effects on metallic

structures and corrosion control systems 1036 NACE RP 0178 Fabrication details, surface finish requirements and proper design

considerations for tanks and vessels to be lined for immersion service 1037 NACE RP0186 Application of cathodic protection for external surfaces of steel

well casings 1038 NACE RP 0188 Discontinuity (holiday) testing of protective coatings 1039 NACE RP0193 External cathodic protection of on-grade carbon steel storage tank

bottoms 1040 NACE RP0196 Galvanic anode cathodic protection of internal submerged

surfaces of steel water storage tanks. 1041 NACE RP0285 Corrosion control of underground storage tank systems by

cathodic protection. 1042 NACE RP0290 Impressed current cathodic protection of reinforcing steel in

atmospherically exposed concrete structures 1043 NACE RP0387 Metallurgical and inspection requirements for cast galvanic

anodes for offshore applications 1044 NACE RP0388 Impressed current cathodic protection of internal submerged

surfaces of carbon steel water storage tanks. 1045 NACE RP0492 Metallurgical and inspection requirements for offshore pipeline

bracelet anodes 1046 NACE RP0572 Design, installation, operation and maintenance of impressed

current deep ground beds 1047 NACE RP0575 Internal cathodic protection systems in oil-treating vessels 1048 NACE TM 01-77 Laboratory testing of metals for resistance to sulphide stress

cracking in H2S environment 1049 NAMUR NE 43 Recommendation for signal levels to extract failure information

from digital transmitters with analogue output. 1050 NAS 1638 Cleanliness requirements of parts used in hydraulic systems 1051 NEMA 250 Enclosures for electrical equipment (1000 volts maximum) 1052 NEMA SM23 steam turbines for mechanical drive service 1053 NEN 547-2 Safety of machinery – human body dimensions, principles for

determining dimensions required for access openings 1054 NEN 1005-3 Manual handling 1055 NEN 3410 Safety requirements for high voltage and low voltage installations in

potentially explosive gas atmospheres 1056 NEN-EN 457 Safety of machinery – auditory danger signals, general design

requirements, design and testing 1057 NEMA MG 1 Motors and generators 1058 NFPA 10 Portable fire extinguishers 1059 NFPA 11 Low expansion foam systems 1060 NFPA 11A Medium and high expansion foam systems 1061 NFPA 11C Mobile foam apparatus



Useful References1062 NFPA 12 Carbon dioxide extinguishing systems 1063 NFPA 15 Water spray fixed systems for fire protection 1064 NFPA 20 Installation of stationary pumps for fire protection 1065 NFPA 58 Standard for storage and handling of liquefied petroleum gases 1066 NFPA 70 National electrical code 1067 NFPA 72 National fire alarm code 1068 NFPA 90A Installation of air conditioning and ventilation systems 1069 NFPA 496 Standard for purged and pressurised enclosures for electrical

equipment in hazardous (classified) locations 1070 NFPA 750 Water mist protection systems 1071 NFPA 2001 Clean agent extinguishing systems 1072 NPR 2760 Mutual influence of pipelines and high voltage circuits 1073 OCIMF Design and construction specification for marine loading arms 1074 OCIMF Recommendations for oil tanker manifolds and associated equipment 1075 PrEN 1005 Safety of machinery - human physical performance 1076 PrEN 12437 Safety of machinery - permanent means of access to machines and

industrial plants 1077 RAL Colours from deutsches institut fur gutesicherung und kennzeichnung e.v.

s.34 engineering recommendation s.34 a guide for assessing rise of earth potential at substation sites

1078 SFA 3009 Special protection 1079 SMACNA HVAC systems - testing, adjusting and balancing 1080 SMACNA HVAC systems - duct design 1081 SMACNA HVAC air duct leakage test manual 1082 SMACNA HVAC systems - applications 1083 SSPC SP1 Surface preparation specification # 1 – solvent cleaning 1084 SSPC PA 2 Paint application specification # 2 – Measurement of dry paint

thickness with magnetic gauges. 1085 TEMA Standards of tubular exchanger manufacturers association 1086 TNO Green book method for determination of possible damage to people and

objects resulting from releases of hazardous materials (CPR 16E – 1992) 1087 UBC 1997 Volume 2 1997 Uniform building code: volume 2; structural

engineering design provisions 1088 UL 698 Safety standard for electrical industrial control equipment for use in

hazardous (classified) locations, class I, groups A,B,C and D and class II, groups E, F and G

1089 UL 698UL 698 UL standard for safety industrial control equipment for use in hazardous (classified) locations.

1090 UL 886 Outlet boxes and fittings for use in hazardous (classified) locations 1091 UL 913 UL standard for intrinsically safe apparatus and associated apparatus for

use in class I, II and III, division I, hazardous (classified) locations 1092 UL - 1709 Rapid rise fire test of protection materials for structural steel 1093 USEPA 40 CFR Part 60 40 Code of federal regulations-Protection of environment

Part 60- Standards of performance for new stationary sources 1094 VDE 0510 Specification for electrical storage batteries and battery plants 1095 VDI 2055 Thermal insulation for heated and refrigerated industrial and domestic

installations 1096 VDI 3733 Noise in pipes 1097 VDI/VDE 3845 Industrial process control valves; interfaces between valves,

actuators and auxiliary equipment



Useful References1098 VGB R-450-Le Guideline for boiler feedwater, boiler water and steam of steam

generators with a permissible operating pressure of >68 bar 1099 WRC 107 Local stresses in spherical and cylindrical shells due to external

loadings 1100 WRC 297 Supplement to WRC bulletin 107
