GTS-PM-ALG-EIG-20 Page 1 of 3
INSTITUT ALGERIEN DE NORMALISATION (IANOR)
CONFORMITY ASSESSMENT PROGRAMME
ISSUED 28-May-14
THE PEOPLE’S DEMOCRATIC REPUBLIC
OF ALGERIA
EXPORTER AND IMPORTER GUIDELINES
ALGERIA CAP EXPORTER AND IMPORTER GUIDELINES
INTRODUCTION In March 2011, the Algerian Ministry of Commerce published a note to all importers reminding them the obligation of submitting a proof of conformity for all shipments entering Algerian territory, to ensure that they meet legal and regulatory requirements that affect them. This obligation is enforced by the law 09-03 dated 25/02/2009 and the decree 05-467 dated 12/12/2005, on conditions and procedures of conformity control of imported goods at customs The conformity assessment of the regulated products is based on the review of existing certificates and test reports, followed by inspection of goods and testing where necessary. On successful conformity assessment, the certification and inspection body issues the Certificate of Conformity (CoC). The required Certificate of Conformity can also be referred as “Certificat de contrôle de qualité”. The original copy of the Certificate of Conformity is needed for every shipment and should be issued in the country of export. It is a mandatory document for Algerian Customs clearance.
OBJECTIVES AND PRINCIPLES The primary objectives of the programme are: To ensure that products imported into Algeria meet the security, safety, health and environment requirements as
per the sanctioned standards and technical regulations approved by IANOR (Institut Algerien de Normalisation).
Provide assurance to the Algerian consumer that the products imported into Algeria are free from potential hazards and fit for use.
To avoid costly delays at the ports and rejection of shipments if the shipments are found to include dangerous and unsafe products.
To help genuine and complying exporters and importers to quickly clear Customs process without the risk of rejection of shipments.
To streamline Custom clearance procedures, promote healthy and fair competition and fight against unsafe and dangerous goods.
THE INTERTEK SOLUTION Intertek pioneered the development of the product conformity assessment programmes, which is now being
applied in many parts of the world to prevent dangerous and unsafe products entering into the market. Intertek has over the years built up vast experience, infrastructure and necessary knowledge in the management of the conformity assessment programmes. To date Intertek has issued more than a million certificates of conformity.
Intertek has a global network of offices that have operated the product conformity programmes for many years. Intertek has experience in providing solutions to businesses exporting a wide range of products to Algeria.
Intertek has undertaken more assessments of more products for longer than any other organization. Intertek has the world’s largest networks of laboratories, which participate in the conformity assessment of
products. These laboratories have a wide range of testing capability including electrical, chemical, automotive goods, building materials and many others.
GTS-PM-ALG-EIG-20 Page 2 of 3
INSTITUT ALGERIEN DE NORMALISATION (IANOR)
CONFORMITY ASSESSMENT PROGRAMME
ISSUED 28-May-14
THE PEOPLE’S DEMOCRATIC REPUBLIC
OF ALGERIA
EXPORTER AND IMPORTER GUIDELINES
ALGERIA CAP EXPORTER AND IMPORTER GUIDELINES
Our staff are experts on the understanding and interpretation of a wide range of national and international standards and requirements including Algerian standard requirements as well as understanding the needs of exporters and importers.
Intertek can provide technical assistance to importers and exporters regarding the sanctioned standards and
regulations Intertek’s Certificates of Conformity includes the latest encryption technology, watermarks and other security
measures which would make it impossible to counterfeit or tamper with. Intertek can provide fast, rapid and tailor made service that meet your particular needs, including:
a. Submission of assessment requests online b. Automated e-mails for status of certificates c. Flexible certificate delivery solutions for high volume users
REGULATED PRODUCT CONSIGNMENT CERTIFICATION PROCESS Regulated product consignments have to be verified for compliance to relevant sanctioned standards, essential requirements or manufacturer’s specification. The compliance verification process may involve physical inspection of the consignment and if necessary sample selection for testing purposes. The certification process is as outlined below: 1. Exporter Submits Request for Certification (RFC) and Supporting Documents
The Exporter contacts the responsible Intertek Country Office and submits a request for certification. Exporter includes the following information along with the request for the certification:
a. Details of products which are included in the shipment b. Name and address of exporter and importer c. Location of consignment and provisional date of availability for inspection d. Payment details, port of discharge, port of loading, mode of transport.
Exporter includes the following documents: a. Test reports/ Reports of analysis/ Quality mark validity proof b. Product specification sheet/ MSDS c. Certificates related to the management of the quality/ safety system (ISO 22000, ISO/TS 16949, ISO
13485…) d. Invoice
Exporter forwards the request for certification and the supporting documents to the Intertek Country Office
2. Country Office (CO) Review of RFC & Submitted Documentation The Country Office reviews the information provided by the exporter and does a preliminary check to verify
whether the substantiating test documents submitted are enough to do a conformity assessment of the products to the sanctioned standards.
If not then the CO will request the exporter to provide more information/documents. At this stage the CO will submit a quotation to the exporter for the inspection and certification costs and if acceptable, the CO office will arrange for the inspection and if necessary removal of samples for laboratory testing/ analysis.
GTS-PM-ALG-EIG-20 Page 3 of 3
INSTITUT ALGERIEN DE NORMALISATION (IANOR)
CONFORMITY ASSESSMENT PROGRAMME
ISSUED 28-May-14
THE PEOPLE’S DEMOCRATIC REPUBLIC
OF ALGERIA
EXPORTER AND IMPORTER GUIDELINES
ALGERIA CAP EXPORTER AND IMPORTER GUIDELINES
3. Consignment Inspection/ Testing by the Appointed Inspector The Country Offices coordinates with the exporter for the inspection of the consignment. Once the inspection has been arranged, the inspector inspects the consignment to verify whether the
products included in the shipment are same as those detailed in the documents submitted for certification, the markings on the product and product’s packaging to ensure it includes the required information, the quantity of the product is as per the invoice and physical condition of the products. If necessary, the inspector may remove samples for additional assessment
4. Issue Certificate of Conformity/ Quality Control
On successful review and conformity assessment of the test reports and inspection result, Intertek will issue
the Certificate of Conformity. If Exporter requires additional original copies of the CoC, these could be provided by the CO.
FEES The party acquiring the certification services is accountable for charges to the conformity assessment related services performed by the conformity assessment Company. These fees cover the cost of inspection, evaluation, testing, and all other technical and administrative activities involved in the shipment certification. An individual quote will be provided to the party requesting for the certification services and agreed upon before commencing with the conformity assessment process.
CONTACT US
INTERTEK GOVERNMENT AND TRADE SERVICES INTERTEK PROGRAMME MANAGEMENT
Academy Place, 1-9 Brook Street, Brentwood, Essex CM 14 5NQ, United Kingdom Tel: +(44) 1277 223 400 Fax: +(44) 1277 220 127 E-mail: [email protected]
14F, Millennium Plaza Tower, Sheikh Zayed Road, Dubai, PO Box 26290, United Arab Emirates Tel: +971 4 317 8777 Fax: +971 4 331 6735 E-mail: [email protected]
APPENDICES*
Appendix A Country Offices Contact Details
Appendix B Request for Certificate of Conformity (RFC)
*These Appendices are available at http://www.intertek.com/government/certificate-of-conformity-for-exports-to-algeria/
Request for Certificate of Conformity* *Request for Technical Inspection Report
*Request for Certificate of Inspection
GTS-PM-CAP-FRM-RFC-22 Page 1 of 4
RFI – For Intertek Use Only
IMPORTANT: The quality and completeness of the documentation submitted by the Applicant directly influences the time and cost of processing
the certification request. This form must be completed in FULL. Applications will not be processed without all of the information completed. If more
space is needed, additional sheets may be attached.
SERVICES REQUESTED
ALGERIA BOTSWANA EGYPT ETHIOPIA GABON
KENYA KSA KUWAIT NIGERIA QATAR
RUSSIA TANZANIA UGANDA OTHERS, (Please Specify):
APPLICANT TYPE
TRADER MANUFACTURER THIRD-PARTY LOGISTICS
AUTHORIZED DEALER AUTHORIZED DISTRIBUTOR OTHERS, (Please Specify):
EXPORTER (APPLICANT) DETAILS
COMPANY NAME:
TRADE LICENCE NO: For KSA Shipments only EXPIRY DATE :
ADDRESS:
CONTACT PERSON: E-MAIL:
TELEPHONE: FAX:
IMPORTER DETAILS
COMPANY NAME: CUSTOMS DEALER NO.: For EGYPT Shipments Only
TRADE LICENCE NO: For KSA Shipments only EXPIRY DATE :
ADDRESS:
CONTACT PERSON: E-MAIL:
TELEPHONE: FAX:
SHIPMENT DETAILS
SHIPMENT LOCATION WHERE GOODS ARE AVAILABLE FOR INSPECTION IF DIFFERENT FROM EXPORTER’S DETAILS
SITE NAME
ADDRESS:
CONTACT PERSON: EMAIL:
TELEPHONE: FAX:
SHIPMENT REFERENCE, IF AVAILABLE
PROFORMA INVOICE: PROFORMA INV. DATE:
L/C NO.: For ALGERIA Shipments Only
FORM M NO.: For NIGERIA Shipments Only
IDF NO.: For KENYA Shipments Only
BL OR AWB NO.:
PAD NO.: For TANZANIA Shipments Only
OTHERS, (Please Specify):
SHIPMENT DELIVERY
PORT OF LOADING: PORT OF DISCHARGE:
VESSEL NAME: COUNTRY OF SUPPLY:
GOODS AVAILABILITY DATE:
EXPECTED SHIPMENT DATE:
GOODS CONDITION NEW SECOND HAND /USED GROSS CONSIGNMENT WEIGHT
MODE OF TRANSPORT: AIR SEA ROAD RAIL
FULL/PARTIAL DELIVERY FULL PARTIAL OTHERS, (Please Specify):
MODE OF SHIPMENT: CONTAINERS
TRAILERS TRUCKS BULK TANKERS OTHERS, (Please Specify): FCL LCL
QUANTITY (NUMBERS)
DOCUMENTS ATTACHED TO THIS APPLICATION
PROFORMA INVOICE PACKING LIST B/L & AWB TEST REPORTS L/C PHOTOGRAPHS OF PRODUCTS
REGISTRATION/LICENCE (SfR/SoR/TER/PC) QMS CERTIFICATES (e.g. ISO 9001, ISO 16949, ISO 22000...) OTHERS, (Please Specify):
Request for Certificate of Conformity* *Request for Technical Inspection Report
*Request for Certificate of Inspection
GTS-PM-CAP-FRM-RFC-22 Page 2 of 4
1
PAYMENT DETAILS RESPONSIBLE PARTY WHO WILL BE PAYING FOR THE SERVICES APPLICANT WILL RECEIVE
PAYMENT-IN-CHARGE: FREIGHT FORWARDER TRADER THIRD PARTY LOGISTICS
MANUFACTURER OTHERS, (Please Specify):
COMPANY NAME:
ADDRESS:
CONTACT PERSON: EMAIL:
TELEPHONE: FAX:
PAYMENT TYPE: CASH CREDIT INTERTEK CREDIT REF. NO.:
ADDRESS WHERE INVOICE TO BE SENT CURRENCY TO BE USED FOR INVOICES
USD JPY GBP INR EUR
CNY OTHERS, (Please Specify):
REMARKS AND COMMENTS
IN GENERAL, ALL IMPORTED GOODS SUBJECT TO SPECIFIC PROGRAMME REQUIREMENTS MAY BE SUBJECTED OR RANDOMLY SELECTED FOR A SECONDARY INSPECTION AND TESTING FOR BOTH SECURITY AND TRADE COMPLIANCE PURPOSES AT THE CUSTOMS TERRITORY. INTERTEK PERFORMS THE EVALUATION OF CONFORMITY BASED ON A RANDOM SAMPLING OF YOUR PRODUCTS AND ON TESTING OF LIMITED PARAMETERS THROUGH A RISK ASSESSMENT APPROACH. THUS, BY SIGNING THIS REQUEST FORM, YOU TAKE YOUR OWN RESPONSIBILITY AND COMMIT TO FULFILL THAT YOU ARE AWARE OF THE CUSTOMS LEGISLATIVE AND REGULATORY REQUIREMENTS GOVERNING THE IMPORT OF YOUR PRODUCTS.
DECLARATION I/WE DECLARE THAT ALL PRODUCTS LISTED ON THIS APPLICATION ARE NOT AFFECTED BY ANY PRODUCT RECALLS NOR THESE ARE SUBSTANDARD OR COUNTERFEIT, TO THE BEST OF OUR KNOWLEDGE. I/WE ALSO DECLARE UNDER OUR OWN RESPONSIBILITY THAT THE PRODUCTS LISTED IN THIS APPLICATION TO WHICH THIS DECLARATION OF CONFORMITY RELATES, SATISFY THE REQUIREMENTS OF THE STANDARDS AND OTHER NORMATIVE DOCUMENTS APPLICABLE FOR THE GOODS FOR EXPORT. I/WE CONSENT TO INTERTEK’S TERMS AND CONDITIONS AND THE REQUIREMENTS STATED HEREIN, WHICH FORM AN INTEGRAL PART OF THIS APPLICATION. I/WE ALSO AGREE TO SHARE ANY OF THE DATA, RESULTS AND DOCUMENTATION GATHERED AND GENERATED DURING THE PERFORMANCE OF THIS SERVICE WITH THE CONCERNED AUTHORITIES
NAME: SIGNATURE:
POSITION: DATE:
***********************************************
SUBMISSION OF THIS APPLICATION CONFIRMS CONSENT TO THE TERMS SET OUT BELOW
1. Unless otherwise explicitly agreed between the parties in writing, any Certificate or report issued in response to this application is issued strictly subject to Intertek's General Terms
and Conditions, a copy of which is available from our nearest Country Office or at our website: http://www.intertek.com/terms/.
2. Intertek represents and warrants that any Certificate or report issued in response to this RFC is issued in good faith and in the reasonable belief that it has authority to do so from the respective authorities or within the provisions of relevant decrees issued by them.
3. The Request for Certification (RFC) sets out the entire agreement and understanding between the parties in relation to its subject matter. The Exporter acknowledges that, in submitting the RFC, it has not relied on any oral or written representation, warranty, or other assurance (except as provided for or referred to in this RFC) and waives all rights and remedies which might otherwise be available to it in respect thereof, provided always, that nothing in this clause limits or excludes any liability for fraud.
4. Inspection Auditors and/or Observers from the Country Office are to be allowed access to the Exporter’s inspection site without prior notice for the purpose of ensuring that a recently performed inspection has been correctly conducted. The Auditors and/or Observers are authorized by the Country Office to amend or overturn the inspection outcome if the result of the audit supports this action. In their course of action, Inspection Auditors and/or Observers will not hamper or hinder the export process.
5. In the event of conflict between the Exporter and an Approved Laboratory relating to the testing of the products, the dispute shall be resolved by the two parties, without
involvement or responsibility on the part of the Country Office (CO), Registration and Licensing Centre (RLC), Centre of Technical Expertise (CTE) or Programme Management (PM). PM shall be informed of such dispute to allow a reassessment of the laboratory’s approval status to be made if warranted.
6. In the event of conflict between the Exporter and any of the COs, RLCs or CTEs relating to the inspection, evaluation, licensing, registration or certification of the regulated products, the Exporter shall be entitled to submit a complaint to the CO, RLC or CTE. If no agreement can be reached, the exporter is entitled to submit an appeal to the Programme Management within two (2) weeks from the date of submittal of the complaint to the CO, RLC or CTE. Documents supporting the Exporter’s point of view shall be attached to the appeal. Programme Management undertakes to investigate the complaint in accordance with Intertek’s internal complaints procedure, and issue a decision thereon within one (1) month from the date of receipt.
7. The Exporter is responsible for informing Intertek in advance of any applicable import/export restrictions that may apply, including instances where products, information or technology may be exported to a country that is restricted or banned from such export.
8. The Exporter commits to fulfill the certification requirements, including implementation of appropriate changes as and when advised by Intertek.
9. The Exporter makes all the necessary arrangements for the investigation of complaints, should the need arise.
10. The Exporter commits to use the Conformity Certificate solely for the purpose for which it has been issued for and must refrain from any form of misuse or make any statement that may cause disrepute to Intertek. The Conformity Certificate issued is only for the shipment verified by Intertek and must not be used in communication media and marketing documents to indicate otherwise. The Exporter must not use the Intertek logo in any documents, brochures, etc. without prior consent from Intertek.
11. If the Exporter provides copies of the Conformity Certificate to other party, the document shall be reproduced in its entirety.
12. The service undertaken by Intertek does not absolve the Buyer and Seller from their contractual obligations to each other, or from compliance with any other import or export regulations.
13. Unless otherwise explicitly agreed between the parties in writing, the above conditions shall be governed by English law and any dispute arising out of this RFC to which these conditions apply shall be subject to the jurisdiction of the English Courts. This Clause supersedes Clauses 22 and 24 in Intertek’s General Terms and Conditions with respect to jurisdiction.
*********************************************
Thank you for taking the time in filling out this form. We appreciate your business!
Request for Certificate of Conformity* *Request for Technical Inspection Report
*Request for Certificate of Inspection
GTS-PM-CAP-FRM-RFC-22 Page 3 of 4
NOTE: Applicant need not complete the below table with the requested information if the submitted invoice/shipment documents includes this information or if this is provided separately in an easily editable electronic
format (e.g. word, excel, rich text format document). If you need to provide more information than the available space permits, please attach EXTRA SHEETS using same format as below.
PRODUCT DETAILS EXCEPT AUTOMOTIVE VEHICLES
PRODUCT CATEGORY
QUANTITY PACKING PRODUCT DESCRIPTION HS CODE BRAND COUNTRY OF ORIGIN
MANUFACTURER’S NAME AND ADDRESS STANDARD REFERENCE
REGISTRATION / LICENCE
(SfR/SoR/TER/ PC) (IF AVAILABLE)
ADDITIONAL INFORMATION PROVIDED ON SEPARATE SHEETS: YES NO. OF ADDITIONAL SHEETS NO
ACRONYMS USED L/C - Letter Of Credit IDF - Import Declaration Form PAD – Pre-Arrival Declaration BL – Bill of Lading AWB – Airway Bill FCL – Full Container Load LCL - Less than Container Load QMS - Quality Management Systems SfR – Statement for Registration PC – Product Certificate
USD – US Dollars GBP – Great British Pound JPY – Japan Yen INR – Indian Rupee EUR – Euro CNY - China Yuan Renminbi HS Code- Harmonized Commodity Description and Coding System SoR – Statement of Registration TER - Technical Evaluation Report
Request for Certificate of Conformity* *Request for Technical Inspection Report
*Request for Certificate of Inspection
GTS-PM-CAP-FRM-RFC-22 Page 4 of 4
NOTE: Applicant need not complete the below table with the requested information if the submitted invoice/shipment documents includes this information or if this is provided separately in an easily editable electronic
format (e.g. word, excel, rich text format document). If you need to provide more information than the available space permits, please attach EXTRA SHEETS using same format as below.
PRODUCT DETAILS FOR AUTOMOTIVE VEHICLES
MAKE/BRAND (E.G. TOYOTA)
VEHICLE TYPE (E.G. PASSENGER CAR)
VEHICLE MODEL (E.G. COROLLA 1.8GLI)
YEAR (E.G. 2010)
COUNTRY OF ORIGIN VIN NUMBER
ADDITIONAL INFORMATION PROVIDED ON SEPARATE SHEETS: YES NO. OF ADDITIONAL SHEETS NO
GTS-PM-ALG-EIG-CCD-00 Page 1 of 8
INSTITUT ALGERIEN DE NORMALISATION (IANOR)
CONFORMITY ASSESSMENT PROGRAMME
ISSUED 28-May-14
THE PEOPLE’S DEMOCRATIC
REPUBLIC OF ALGERIA
EXPORTER AND IMPORTER GUIDELINES
APPENDIX A – COUNTRY OFFICES CONTACT DETAILS
COUNTRY COUNTRY OFFICE CONTACT DETAILS ZONES OF RESPONSIBILITY
B
R
A
Z
I
L
Phone +55 11 5015 4200 Argentina Paraguay
Contact Marcos Gobbi Bolivia Peru
Mobile +55 11 98228 1591 Brazil Uruguay
Contact Diva Nascimento Chile
Mobile +55 11 95201 0004
Email [email protected]
Office Address
Intertek Do Brasil Inspeções Ltda Av. Leonardo da Vinci, 1034 – Vila Guaraní CEP 04313-000 – São Paulo – SP Brazil
COUNTRY COUNTRY OFFICE CONTACT DETAILS ZONES OF RESPONSIBILITY
C
H
I
N
A
GUANGZHOU China
Phone +86 20 3210 2000
Phone +86 20 8213 9122
Fax +86 20 3220 6081
Contact Jasmine Lin
Mobile +86 181 2238 2221
Email [email protected]
Office Address
Intertek Testing Services Shenzhen Ltd. GZ GDD Branch C301, No.7-2 Caipin Road, Guangzhou Science City, GETDD Guangzhou, China
HONG KONG Australia Hong Kong Solomon Island
Phone +852 2 310 9923 China Macau Taiwan
Fax +852 2 370 2284 Christmas Island New Caledonia Tokelau
Contact Shirley Li Cook Islands New Zealand Tuvalu
Email [email protected] Fiji Niue Vanuatu
Office Address
Intertek Testing Services Hong Kong Ltd 5B Garments Centre 576 Castle Peak Road, Kowloon, Hong Kong
French Polynesia Norfolk Island Western Samoa
Heard Island Papua New Guinea
CUSTOMER SERVICE CENTRE - TAIWAN
Phone +886 2 6602 2888 Ext. 796
Fax +886 2 6602 2889
Contact Serina Lu
Mobile +886 9 7295 3797
Contact Yue Yang
Email [email protected]
Office Address
Intertek Testing Services Ltd 8F, No.423, Ruiguang Road, Neihu District Taipei 11492, Taiwan
GTS-PM-ALG-EIG-CCD-00 Page 2 of 8
INSTITUT ALGERIEN DE NORMALISATION (IANOR)
CONFORMITY ASSESSMENT PROGRAMME
ISSUED 28-May-14
THE PEOPLE’S DEMOCRATIC
REPUBLIC OF ALGERIA
EXPORTER AND IMPORTER GUIDELINES
APPENDIX A – COUNTRY OFFICES CONTACT DETAILS
COUNTRY COUNTRY OFFICE CONTACT DETAILS ZONES OF RESPONSIBILITY
C
H
I
N
A
SHANGHAI China
Phone +862 1 6887 9250
Fax +862 1 5840 1622
Fax +862 1 5840 1674
Contact Owen Ye
Contact Wang Liqin
Contact Cathy Zang
Email [email protected]
Office Address
Intertek Testing Services Ltd. Shanghai 16F, Fangdi Mansion No. 201 NanQuan Road (North) Lujiazui Finance & Trade Zone Pudong, Shanghai, China 200120
CUSTOMER SERVICE CENTRE - NINGBO
Phone +865 74 8818 3650
Phone +865 74 8818 3658
Fax +865 74 8818 3657
Contact Albert Zhang
Mobile +861 88 6867 8262
Email [email protected]
Office Address
Intertek Commodities 5F East No.6 Building Lingyun Industry Park, No.1177 Lingyun Road, Ningbo National Hi-Tech Zone, Ningbo, 315000 China
CUSTOMER SERVICE CENTRE - QINGDAO
Phone +865 32 8099 3788
Phone +865 32 8099 3267
Fax +865 32 8099 3737
Contact Sarah Duan
Mobile +861 89 5426 9191
Email [email protected]
Office Address
Intertek Government & Trade Services 26 Keyuanjingyi Road, Qingdao, Shandong, 266100 China
GTS-PM-ALG-EIG-CCD-00 Page 3 of 8
INSTITUT ALGERIEN DE NORMALISATION (IANOR)
CONFORMITY ASSESSMENT PROGRAMME
ISSUED 28-May-14
THE PEOPLE’S DEMOCRATIC
REPUBLIC OF ALGERIA
EXPORTER AND IMPORTER GUIDELINES
APPENDIX A – COUNTRY OFFICES CONTACT DETAILS
COUNTRY COUNTRY OFFICE CONTACT DETAILS ZONES OF RESPONSIBILITY
F
R
A
N
C
E
Phone +33 2 3209 3087 Albania Georgia Morocco
Phone +33 2 3263 3162 Algeria Greenland Netherlands
Contact Leila Senouoa Andorra Hungary Norway
Contact Carole Heliot Armenia Iceland Poland
Email [email protected] Austria Kazakhstan Romania
Office Address
Intertek International SARL Azerbaijan Kosovo Serbia
ZAC EcoParc 2 Belarus Kyrgyzstan Slovakia
27400 Heudeubouville, France Belgium Latvia Slovenia
Bulgaria Lithuania Sweden
Croatia Luxembourg Tajikistan
Czech Republic Macedonia Tunisia
Denmark Moldova Turkmenistan
Estonia Monaco Ukraine
Faro Islands Montenegro Uzbekistan
Finland Bosnia & Herzegovina
CIS former Russia France Metropolitan
French Southern Territory
Svalbard & Jan Mayen
COUNTRY COUNTRY OFFICE CONTACT DETAILS ZONES OF RESPONSIBILITY
G
E
R
M
A
N
Y
Phone +49 40 513 275-0 Germany
Fax +49 40 513 275-55
Contact Irina Baerenwald
Mobile +49 160 907 2 4641
Email [email protected]
Office Address
Intertek Caleb Brett Germany GmbH Sachsentor 1 D-21029 Hamburg, Germany
COUNTRY COUNTRY OFFICE CONTACT DETAILS ZONES OF RESPONSIBILITY
I
T
A
L
Y
Phone +39 02 9538 3833 Greece Switzerland
Fax +39 02 9538 3832 Italy Turkey
Contact Eleonora Piumelli Liechtenstein Vatican City
Contact Verdiana Brambilla San Marino
Email [email protected]
Office Address
Intertek Italia SPA Via Aldo Moro, 47, 20060 Gessate, Milano, Italy
GTS-PM-ALG-EIG-CCD-00 Page 4 of 8
INSTITUT ALGERIEN DE NORMALISATION (IANOR)
CONFORMITY ASSESSMENT PROGRAMME
ISSUED 28-May-14
THE PEOPLE’S DEMOCRATIC
REPUBLIC OF ALGERIA
EXPORTER AND IMPORTER GUIDELINES
APPENDIX A – COUNTRY OFFICES CONTACT DETAILS
COUNTRY COUNTRY OFFICE CONTACT DETAILS ZONES OF RESPONSIBILITY
I
N
D
I
A
Phone +91 22 6693 4848 Bangladesh
Fax +91 22 6693 4800 India
Contact Sridhar Raghavan Nepal
Contact Gladys Manke-Pandhi Sri Lanka
Contact Rajul Navalkar
Email [email protected]
Office Address
Intertek India Private Ltd
401 Everest House, 4th Fl
6 Suren Road, Andheri (East)
Mumbai – 400093, India
COUNTRY COUNTRY OFFICE CONTACT DETAILS ZONES OF RESPONSIBILITY
J
A
P
A
N
Phone +81 3 5245 0665 Japan
Fax +81 3 5245 0474
Contact Katsumi Murakami
Contact Yoko Nagashima
Contact Shigeru Iwata
Email [email protected]
Office Address
Intertek Testing Services (Japan) KK
7F, Ichigo Eitai Building, 2-31-1, Eitai Koto-ku, Tokyo 135-0034, Japan
COUNTRY COUNTRY OFFICE CONTACT DETAILS ZONES OF RESPONSIBILITY
J
O
R
D
A
N
Phone +96 2 6577 7905 Jordan
Phone +96 2 6500 4444
Fax +96 2 6500 4017
Contact Kareem Naouri
Email [email protected]
Office Address
Um Uthinah, Saaed Bin Abi Waqqas St., Naouri Building #29, Amman - Jordan
COUNTRY COUNTRY OFFICE CONTACT DETAILS ZONES OF RESPONSIBILITY
M
E
X
I
C
O
Phone +52 55 5357 3625 Mexico
Phone +52 55 5998 0900
Fax +52 55 5358 5710
Contact Rosa Marquez
Email [email protected]
Office Address
Intertek Testing Sevices de Mexico S.A. de C.V. Calle Poniente 134 #660 Col. Industrial Vallejo Del. Azcapotzalco, Distrito Federal, C.P. 02300 Mexico
GTS-PM-ALG-EIG-CCD-00 Page 5 of 8
INSTITUT ALGERIEN DE NORMALISATION (IANOR)
CONFORMITY ASSESSMENT PROGRAMME
ISSUED 28-May-14
THE PEOPLE’S DEMOCRATIC
REPUBLIC OF ALGERIA
EXPORTER AND IMPORTER GUIDELINES
APPENDIX A – COUNTRY OFFICES CONTACT DETAILS
COUNTRY COUNTRY OFFICE CONTACT DETAILS ZONES OF RESPONSIBILITY
K
E
N
Y
A
Phone +254 20 444 9132 to 33 Benin Gambia Niger
Phone +254 20 444 9136 Burkina Faso Ghana Rep. of the Congo1
Phone +254 20 815 5274 to 75 Burundi Guinea Rwanda
Fax +254 20 444 9212 Cameroon Guinea-Bissau Senegal
Fax +254 20 444 6246 Cape Verde Ivory Coast Sierra Leone
Contact Victor Mbithi Chad Kenya Somalia
Mobile +254 714 900 397 Djibouti Liberia Tanzania
Contact Rosemary Mwangi Equatorial Guinea Mali Republic Togo
Email [email protected] Eritrea Mauritania Uganda
Office Address
Intertek International Ltd Ethiopia Nigeria Western Sahara
4F House of Vanguard Chiromo Road Gabon Central African Republic
Consolata Church Westlands, Kenya Dem. Rep. of the Congo2
Delivery Address
Village Market PO Box 696, Sao Tome & Principe
00621 Nairobi, Kenya
COUNTRY COUNTRY OFFICE CONTACT DETAILS ZONES OF RESPONSIBILITY
S.
K
O
R
E
A
Phone +82 2 775 5255 South Korea
Fax +82 2 775 5266
Contact Monica Kim
Contact Rachel Lee
Contact Paul Kim
Email [email protected]
Office Address
Intertek Testing Services Korea Ltd.
6F, Ace Techno Tower 5,
#20, Digital-Ro, 31-Gil, Guro-Gu,
Seoul 152-766, Korea
COUNTRY COUNTRY OFFICE CONTACT DETAILS ZONES OF RESPONSIBILITY
S
P
A
I
N
Phone +34 94 611 3565 Canary Islands
Phone +34 94 611 3560 Portugal
Fax +34 94 435 6600 Spain
Contact Nerea de Miguel
Contact Alicia Malmierca
Email [email protected]
Office Address
Intertek Ibérica Spain SAU
5F 27 Alameda, Recalde
48009 Bilbao, Spain
1 Brazaville
2 Zaire
GTS-PM-ALG-EIG-CCD-00 Page 6 of 8
INSTITUT ALGERIEN DE NORMALISATION (IANOR)
CONFORMITY ASSESSMENT PROGRAMME
ISSUED 28-May-14
THE PEOPLE’S DEMOCRATIC
REPUBLIC OF ALGERIA
EXPORTER AND IMPORTER GUIDELINES
APPENDIX A – COUNTRY OFFICES CONTACT DETAILS
COUNTRY COUNTRY OFFICE CONTACT DETAILS ZONES OF RESPONSIBILITY
S
I
N
G
A
P
O
R
E
SINGAPORE Bhutan Malaysia Palau
Phone +65 6 285 7557 Brunei Maldives Philippines
Fax +65 6 382 8662 Cambodia Marshall Island Pitcairn
Contact Serene Chan Cocos Island Micronesia Singapore
Mobile +65 9 652 9955 East Timor Mongolia Thailand
Email [email protected] Indonesia Myanmar Tonga
Office Intertek Testing Services Kiribati Nauru Vietnam
Address Ltd 04-01 Asiawide Industrial Laos Pacific Island Malaysia
Building 5 Pereira Road 368025 British Indian Ocean Territory
Singapore Northern Mariana Island
Wallis and Futuna
CUSTOMER SERVICE CENTRE - PHILIPPINES
Phone +63 2 819 5841 to 47
Phone +63 2 868 2343
Fax +63 2 813 8915
Contact Annabelle Valdez
Mobile +63 920 952 7309
Contact Alexander Javier
Mobile +63 917 591 0366
Email [email protected]
Office Address
Intertek International Ltd. Unit 501, Tower One & Exchange Plaza, Ayala Avenue corner Paseo de Roxas, Makati City, Philippines 1226
CUSTOMER SERVICE CENTRE - THAILAND
Phone +662 938 1990 Ext. 201
Fax +662 938 1923
Contact Serene Chan
Mobile +668 900 42003
Contact Suthee Kongsiriwong
Email [email protected]
Office Address
Intertek Testing Services Ltd
4F Univest Complex No. 546,
Ratchadapisek Road, Chankasem
Chatuchak, Bangkok 10900 Thailand
GTS-PM-ALG-EIG-CCD-00 Page 7 of 8
INSTITUT ALGERIEN DE NORMALISATION (IANOR)
CONFORMITY ASSESSMENT PROGRAMME
ISSUED 28-May-14
THE PEOPLE’S DEMOCRATIC
REPUBLIC OF ALGERIA
EXPORTER AND IMPORTER GUIDELINES
APPENDIX A – COUNTRY OFFICES CONTACT DETAILS
COUNTRY COUNTRY OFFICE CONTACT DETAILS ZONES OF RESPONSIBILITY
S.
A
F
R
I
C
A
Phone +2711 914 4044 Angola Mauritius South Africa
Fax +2711 914 4217 Botswana Mayotte St. Helena
Contact Cobus Alberts Comoros Island Mozambique Swaziland
Contact Chevis Coetzee Lesotho Namibia Zambia
Contact Donne Walt Madagascar Reunion Island Zimbabwe
Contact Tammy De Beer Malawi Seychelles Island
Email [email protected]
Office Address
Intertek International Ltd
Van Dyk Secure Business Park
Unit 96G Corner Van Dyk and
Brakpan Roads
Boksburg Industrial East
Boksburg P. O. Box 280
Gauteng, South Africa
COUNTRY COUNTRY OFFICE CONTACT DETAILS ZONES OF RESPONSIBILITY
U
A
E
Phone +971 4 317 8777 Afghanistan Lebanon Saudi Arabia
Fax +971 4 331 6883 Bahrain Libya UAE
Contact Husny Saeed Egypt Oman Yemen
Contact Hiyam Qandah Iraq Pakistan
Email [email protected] Kuwait Qatar
Office Address
Intertek International Ltd
Government and Trade Services
Middle East.
14F Millennium Plaza Tower
Sheikh Zayed Road P.O. Box 26290,
Dubai, U.A.E.
COUNTRY COUNTRY OFFICE CONTACT DETAILS ZONES OF RESPONSIBILITY
U
K
Phone +44 1277 223 255 Cayman Island Israel
Phone +44 1277 223 400 Cyprus Malta
Fax +44 1277 220 127 Gibraltar UK
Contact Pollyesther Njoki Ireland
Email [email protected]
Office Address
Intertek International Ltd.
Academy Place, 1-9 Brook Street
Brentwood Essex CM14 5NQ UK
GTS-PM-ALG-EIG-CCD-00 Page 8 of 8
INSTITUT ALGERIEN DE NORMALISATION (IANOR)
CONFORMITY ASSESSMENT PROGRAMME
ISSUED 28-May-14
THE PEOPLE’S DEMOCRATIC
REPUBLIC OF ALGERIA
EXPORTER AND IMPORTER GUIDELINES
APPENDIX A – COUNTRY OFFICES CONTACT DETAILS
COUNTRY COUNTRY OFFICE CONTACT DETAILS ZONES OF RESPONSIBILITY
U
S
A
Phone +1 305 513 3000 American Samoa Ecuador Panama
Fax +1 305 513 3001 Anguilla El Salvador Puerto Rico
Contact Francisco Ibern Antarctica Falkland Island South Georgia
Contact Elena Contreras Antigua & Barbuda French Guiana St. Kitts and Nevis
Email [email protected] Aruba Grenada St. Lucia
Office Intertek International Inc. Bahamas Guadeloupe St. Pierre
Address 8600 NW 17 Street Barbados Guam Suriname
Suite 100, Miami, Florida 33126, USA Belize Guatemala USA
Bermuda Guyana Venezuela
Bonaire Haiti Virgin Island (US)
Canada Honduras Nicaragua
Colombia Jamaica Panama
Costa Rica Martinique Puerto Rico
Curacao Montserrat South Georgia
Dominica Nicaragua St. Kitts and Nevis
Dominican Republic
Netherlands Antilles
St. Vincent & Grenadines
Trinidad and Tobago
Turks and Caicos Island
Virgin Island (British)