· TWO PIECE BODY· FULL PORT· INVESTMENT CAST BODY· BLOWOUT-PROOF STEM· LOCKING DEVICE· ACT. MOUNTING PAD· SIZE RANGE: 1/4” – 3”

· 1000 PSI WOG CWP

· 150 PSI SATURATED STEAM

F e a t u r e s

P/N 1.5.01

Series F112pc. 1000 psi cwp

API 598Valve Inspection and Testing

ASME/ANSI B16.34Valves Flanged, Threaded, and Welding End

ANSI B1.20.Machining of NPT Threaded Ends

ANSI B16.11Machining of Socket Weld Ends

ANSI B16.25Machining of Butt Weld Ends

MSS SP-72-1992Ball Valves General Service

ISO 5211Part-turn Valve Actuator Attachment

DimensionsSeries F11

P/N 1.5.02

mm - in boldSize 1/4 3/8 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3

A 51 51 54 58 66 72 81.5 90.5 138.5 1492.01 2.01 2.13 2.28 2.60 2.83 3.21 3.56 5.45 5.87

B 51 51 59.5 71 88.6 97.5 109.5 133.5 167 1922.01 2.01 2.34 2.80 3.49 3.84 4.31 5.26 6.57 7.56

C 103 103 103 125 145 145 190 190 250 2504.06 4.06 4.06 4.92 5.71 5.71 7.48 7.48 9.84 9.84

DN 11.6 12.7 15 20 25.4 32 38 50.8 65 760.46 0.50 0.59 0.79 1.00 1.26 1.50 2.00 2.56 2.99

F 36 36 36 42 42 42 50 50 70 701.42 1.42 1.42 1.65 1.65 1.65 1.97 1.97 2.76 2.76

ISO 5211 F03 F03 F03 F04 F04 F04 F05 F05 F07 F07G M5 M5 M5 M5 M5 M5 M6 M6 M8 M8

N5 5 5 6.5 8 8 9.7 9.7 12 12

0.20 0.20 0.20 0.26 0.31 0.31 0.38 0.38 0.47 0.47

S117 17 17 18 21 22 22 22 36 41

0.65 0.65 0.65 0.7 0.84 0.87 0.87 0.87 1.4 1.61

S211 11 11 10 15 16 16 17 27 32

0.44 0.44 0.44 0.4 0.58 0.62 0.62 0.65 1.05 1.27

Engineering Data

CF Series F11 with actuator

Size Cvgpm

WeightLbs.

TorqueIn./lbs.

1/4” 6 0.5 36

3/8” 7 0.5 36

1/2” 10 0.7 68

3/4” 25 1.2 104

1” 35 2.1 130

1-1/4” 46 3.1 174

1-1/2” 80 5.1 217

2” 110 8 260

2-1/2” 310 14 430

3” 360 23 870

pres

sure

in p

si

temperature in degrees F

Pressure / Temperature Rating

P/N 1.5.03

Use the actuator sizing below to estimate the amount of space neededto install the stated CF automation assembly. The valve and actuatorcombinations are configured according to the above torque figuresreflecting the maximum "seatbreak" torque required to move the ballfrom fully open or closed position and reseat the valve in clean/wet

service at ambient temperature and valve's maximum working pressure.A number of factors may increase the operating torque of these valves.Therefore, size the actuator for your specific conditions. If unsure, selecta larger actuator.

Size DA seriesPneumatic

SR seriesPneumatic

Electricactuator

1/4” 6.50DA32

7.45SR52

9.5LCR-150

3/8” 6.50DA32

7.45SR52

9.5LCR-150

1/2” 6.75DA32

6.65SR52

9.8LCR-150

3/4” 6.75DA52 SR63

7.23 10.0LCR-150

1” 6.95DA52

6.95SR75

10.25LCR-150

1-1/4” 7.25DA63

8.25SR85

11.50LCR-300

1-1/2” 8.55DA63

8.75SR85

11.50LCR-300

2” 8.75DA63

10.25SR100

13.00LCR-300

2-1/2” 11.25DA75

12.75SR100

15.50LCR-600

3” 15.75DA85

16.35SR115

18.00VW1000

P/N 1.5.04

Ordering Number System

Part Name MaterialNo.

1 Body CF8M

2 End Cap CF8M

3 Seat RPTFE

4 Ball 316SS

5 Body Seal PTFE

6 Thrust Washer PTFE

7 Stem 316SS

8 Packing PTFE

9 Packing Nut AISI 304

10 Lever AISI 304

11 Lock Washer AISI 304

12 Lever Nut AISI 304

13 Lever AISI 304

C ASTM A351 gr. CF8M 316 Stainless Steel

SR,DA Pneumatic ActuatorLC,V Electric Actuator- No Options1 Manual Gear Operator2 Extended Stem Manual Operator3 Round/Oval Handwheel Operator4 Cryogenic Extension5 Cleaned for Oxygen Service6 Spring Return Lever Operator7 Spring Return with fusible link0 Other

F11 Two piece, Full Port1000psi CWP WOG 1/4”-3”

S Screwed End - SE, NPT

R 15% Glass Reinforced PTFET Virgin PTFEP PEEKC Carbon Graphite RPTFES Stainless Steel RPTFE

bodymaterial size

R C 1F11series ends seats

Svalve options

SERIES

VALVE OPTIONS

ENDS

SEATS

BODYMATERIAL

Due to our dynamic product development and innovation, CF Fluid Controls Inc. reserves the right to modify any of the products and information within this brochure without prior notification.

Components