Rev. B 01/18/06
REMOTE ENGINE STARTER
TROUBLESHOOTING GUIDE
2008- LAND CRUISER TVIP V4 REMOTE ENGINE STARTER (RES) TROUBLESHOOTING GUIDE
Remote Engine Starter Troubleshooting Guide Page 2
TABLE OF CONTENTS
DESCRIPTION PAGE
PRE-CHECK 3
RES ECU PIN LAYOUT AND TERMINALS 4-5
ACCESSORY GATEWAY ECU PIN LAYOUT AND TERMINALS 6
HOW TO PROCEED WITH TROUBLESHOOTING 7
CUSTOMER PROBLEM ANALYSIS CHECK 8
PROBLEM SYMPTOMS TABLE 9
DIAGNOSTIC OPERATION 10-11 Diagnosis Mode Reset Conditions 12
DIAGNOSTIC CODE BY SCAN TOOL 12
INSPECTIONS Engine Does Not Start by Remote 13-15 Engine Does Not Stop by Remote 16-17Engine Stops Unexpectedly 18-19 Failed Registration of Immobilizer ID Code 20-21
Remote Engine Starter Troubleshooting Guide Page 3
PRE-CHECK
REMOTE ENGINE STARTER CHARACTERISTICS
(a) The operation distance varies according to how customers hold the transmitter or where it is used.
(b) Strong external radio waves or other frequency noise may interfere with the Remote Engine Starter’s operation distance.
REMOTE ENGINE STARTER BASIC FUNCTIONS
(a) Stand on the driver’s side, three feet away from the vehicle.
(b) Turn the transmitter toward the vehicle and press and release the LOCK button twice within two seconds. Immediately press and hold the LOCK button for three seconds. The hazard lights flash after three seconds.
(c) The engine then starts, and the hazard lights flash for 20 seconds.
(d) Press the UNLOCK button. The engine stops and hazard lights flash twice.ORPress and hold the LOCK button for two or more seconds. The engine stops and the hazard lightsflash once.
MPXST1IPRDIGOPI2LDUT
OP13(DSWH)STSWOB2I+BIGI-ST10-GNDGND--OB20
Part Number: 90980-12258 Color: White
MALE FRONT VIEW MALE FRONT VIEW
Part Number: 90980-11361 Color: White
Remote Engine Starter Troubleshooting Guide Page 4
RES ECU PIN LAYOUT <Connector>
910 8 7 6 5 4 3 2 1
20 19 18 17 16 15 14 13 12 11
12
8 7 6 5 4 3
*1: Vehicles without Push Start System only.*2: Vehicles with Push Start System only.
Terminal No.
Content Signal
1 MPX Signal 2 ST1 Input *1 3 SHIFT P 4 RES Diag 5 OPTIONINPUT2 6 CHECK ENGINE
LIGHT7 OPTIONINPUT3 8 (HOOD SW.) 9 STSW Signal *2 10 OBD2 (Diag.) *1 11 +B 12 IG113 N.C. 14 ST1 Output *1 15 N.C. 16 GND 17 GND 18 N.C. 19 N.C. 20 OBD2 (Imm. ECU) *1
Terminal No.
Content Signal
1 AM1 *1 2 AM2 *1 3 IGI *1 4 N.C. 5 ACC *1 6 ST2 *1 7 N.C. 8 IG2 *1
AM1AM2IG1-ACCST2-IG2
Remote Engine Starter Troubleshooting Guide Page 5
RES ECU TERMINALS
Remote Engine Starter ECU Input/Output Specifications
Signal Symbol I/O Condition +B +B ECU+B 12V (TYP) GND E ECU GND 0 V AM1 *1 AM1 Input AM2 *1 AM2 Input IG1 *1 IG1 Output IG2 *1 IG2 Output ACC *1 ACC Output ST2 *1 ST2 Output
Dropping voltage: Less than 0.2V
IG1(same terminal as above)
IG1 Input ON : Over (+B-1) V
Hood SW DSWH Input Close : Less than 1V Shift position P P Input ON : Over (+B-1) V Check engine lamp
LDUT Input OFF : Less than 2.2V ON : Over 6V
Diagnosiscommunication1 *1
OB2I Input Pulse generation during communication
Diagnosiscommunication2 *1
OB2O Output Pulse generation during communication
BEANcommunication
MPX Commu- nication
Pulse generation
ST1(IN) *1 ST1I Input ON : Over (+B-1)V ST1(OUT) *1 ST1O Output Permissible current : 500mA STSW *2 STSW Output ON : Over (+B-2) V Remote engine starter diagnosis input
RDIG Input ON : Less than 1V
*1: Vehicles without Push Start System only.*2: Vehicles with Push Start System only.
Part Number: 90980-10798 Color: Dark gray
MALE FRONT VIEW
Remote Engine Starter Troubleshooting Guide Page 6
ACCESSORY GATEWAY ECU PIN LAYOUT
<Connector>
ACCESSORY GATEWAY ECU TERMINALS
Accessory gateway ECU Input/Output Specifications
Signal Symbol I/O Condition +B +B ECU+B 12V (TYP) GND E ECU GND 0 V MPX signal for accessory
MPXY Commu- nication
MPX signal for Vehicle LAN
MPX Commu- nication
Pulse generation
5 4 3 2 1
Terminal No. Content Signal
1 MPX Signal for Accessory MPXY 2 N.C. _ 3 +B +B 4 GND GND 5 MPX Signal for Vehicle MPX
Remote Engine Starter Troubleshooting Guide Page 7
HOW TO PROCEED WITH TROUBLESHOOTING
HINT Use these procedures to troubleshoot the Remote Engine Starter. The hand-held tester should be used in Step 4.
1 VEHICLE BROUGHT IN FOR SERVICE
2 CUSTOMER PROBLEM ANALYSIS CHECK AND SYMPTOM CHECK
3 PROBLEM SYMPTOMS TABLE
4 OVERALL ANALYSIS AND TROUBLESHOOTING (a) Diagnostic Mode check, if necessary (see page 10) (b) Check ECU terminals (see pages 4 to 6) (c) Check wire harness (see I/I and EWD)
5 Please fax the Replacement Authorization Request Sheet and Customer Problem Analysis Check Sheet to (800) 438-5410 to receive an RES Authorization Number. For assistance, please call Fujitsu Ten Technical Support at (800) 237-5413.
7 CONFIRMATION TEST
END
6 CHECK INSTALLATION AND PROGRAMING, REPAIR OR REPLACE
NEXT
NEXT
NEXT
NEXT
NEXT
NEXT
NEXT
Remote Engine Starter Troubleshooting Guide Page 8
CUSTOMER PROBLEM ANALYSIS CHECK
Today’s date:_____________ __
Customer’s Name R.O. No.
Problem Conditions Verified Unable to verify Date Problem First Occurred (M) /(D) / (Y) Where did the problem occur? Home Work OtherHow far from the user was the car? Less than 5 feet 5 to 10 feet
10 to 30 feet More than 30 feet When did the problem occur? After car repaired After engine stalled
After other accesorry installed After change to new car key or transmitter
How often has the problem occurred? Always Sometimes Once only
Weather Clear Cloudy Rainy Snowy Various/Other
Weather Conditions When Problem Occurred Outdoor
Temperature Hot Warm Cool Very Cold Approx. Deg F
Customer Complaint (After completing inspection, please select one from below, or choose “other” if not applicable.) Engine did not start (1) Was the Immobilizer code registration confirmed?
Yes No (2) How many times did the hazard lights flash in
Diagnostic Mode? ____ times Engine stopped unexpectedly (1) Was the total run time under 20 minutes?
Yes No(2) How many times did the hazard lights flash in
Diagnostic Mode? ____ times Engine did not stop (1) What condition was present when the problem occurred?
LOCK button pressed and held UNLOCK button pressed Engine ran more than 10 min. Hood was open
Key was in ignition or push start button was pressed “Check Engine” light came on Other ________________________________________
Other (Please explain in detail) ___________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
REMOTE ENGINE STARTER SYSTEM Check Sheet
Remote Engine Starter Troubleshooting Guide Page 9
PROBLEM SYMPTOMS TABLE
Symptom Check item See page Engine does not start by remote.
1. Remote keyless entry operation 2. Engine operation 3. Remote E/G start operation 4. Remote Engine Starter diagnosis 5. Vehicle circuit (Engine Starter ECU
input/output check) 6. Immobilizer ID code registration
13
Engine does not stop by remote.
1. Remote keyless entry operation 2. Remote E/G stop operation 3. Vehicle circuit (Engine Starter ECU
input/output check)
16
Engine stops unexpectedly. 1. Total operation time (Run time) 2. Remote Engine Starter Diagnosis 3. Vehicle circuit (Engine Starter ECU
input/output check)
18
Registration of ID code of Immobilizer failed.
1. Immobilizer ID code registration operation
2. Vehicle circuit (Engine Starter ECU input/output check)
20
Remote Engine Starter Troubleshooting Guide Page 10
DIAGNOSTIC OPERATION
ENGINE STARTER DIAGNOSIS
NOTE: Turn the engine off before performing any diagnostic function.
The Diagnostic Mode can help determine why the engine stops/fails.To set the Diagnostic Mode, you must locate and connect the Diagnostic Connectors (RDIG). To do so, follow the steps below:
(1) Remove the passenger side step cover.
(2) Remove the passenger side cowl cover.
(3) Find and connect the Diagnostic Connectors (RDIG) with label, located in the passengercowl area.
RES DiagnosticConnectors
Theseconnectorsmust be connected.
Cowl Cover
Nut
Step Cover
Remote Engine Starter Troubleshooting Guide Page 11
Diagnostic Operation
DIAGNOSTIC FACTOR IDENTIFICATION
The Diagnostic Mode indicates the causes of engine stop or failure to start as listed below.
Engine Stop Factor
*1: The immobilizer registration should be confirmed if the connection and terminal signal don’t have any problem. (Only installation timing)
*2: When two or more of these conditions are responsible for the engine stop or non-start, they will be indicated by order of priority.
Engine Stop Factor Hazard Lights Flashing Time
AffectedTerminal
Order of Priority*2
No abnormal stop in the past 0 None 9 Key switch is on 1 MPXY, MPX 1
Any door is unlocked 2 MPXY, MPX 4 Engine RPM is too high or low 3 MPXY, MPX 7
“Check Engine” is indicated 4 LDUT 8Any door or hood is opened 5 MPXY, MPX,
(DSWH)2
Gearshift position is not “P” 6 MPXY, MPX, P 5 Brake is on 7 MPXY, MPX, 3
Vehicle speed is abnormal 8 MPXY, MPX, 6 Discrepancy on Immobilizer Collation. 9 MPX, OB2I, OB2O
*19
Check Engine Connection NG 10 MPX, LDUT 10
IG OFF ON
Hazard Lights Flashing
Press the Brake pedal: < OFF ON (Press) >
Connect the diagnostic connector: < Open GND (Connect) >
Wait for more than 3 seconds
Remote Engine Starter Troubleshooting Guide Page 12
DIAGNOSTIC MODE EXIT CONDITIONS
You may exit the Diagnostic Mode by doing either of the following:
1: Disconnect the diagnostic connectors.OR2: Wait 10 minutes from the time the diagnostic connectors were connected.
After completing the repair, the diagnostic connectors should be disconnected and re-secured prior to reassembly of the trim covers.
NOTE: The Remote Engine Starter will store the code for the last engine stop factor in its memory, even after exiting Diagnostic Mode. The code cannot be cleared from the Remote Engine Starter ECU’s memory.
DIAGNOSTIC CODE BY SCAN TOOL
When RES has the following defects, diagnostic code is indicated by the scan tool.
1: Internal Relay of the RES ECU Abnormality Detected CODE [B2334] 2: Internal Switch of the RES ECU for Vehicle Starter Abnormality Detected CODE [B2333]
If you find the above code by the scan tool, PLEASE CALL Fujitsu Ten Technical Support at (800) 237-5413.
Remote Engine Starter Troubleshooting Guide Page 13
INSPECTION 1/9
(a) Ignition must be “OFF” when starting this procedure.
(a) Press the LOCK button. (b) Confirm the doors are locked.
<Smart Entry Vehicle> (a) Start the engine with the POWER button. (b) Confirm the engine is activated.
<Non Smart Entry Vehicle> (a) Start the engine with the key in the IG key cylinder. (b) Confirm the engine is activated.
3 CHECK REMOTE ENGINE START OPERATION (a) Press and release the LOCK button twice within 2 seconds.
Then immediately press and hold the LOCK button for 3 seconds.
ENGINE DOES NOT START BY REMOTE. INSPECTION PROCEDURE
1 CHECK REMOTE KEYLESS ENTRY OPERATION
2 CHECK ENGINE OPERATION
HINT: EXPLAIN THE FOLLOWING INFORMATION TO CUSTOMER:The transmission range for remote start may be shorter than the remote’s basic keyless entry operation. Range can also be affected by the surrounding environment.
END
GO TO VEHICLE’S REPAIR MANUAL AND CHECK ENGINE OPERATION
OK
OK
GO TO VEHICLE’S REPAIR MANUAL AND CHECK REMOTE KEYLESS ENTRY OPERATION
NO
NO
NO
OK
GO TO STEP 4
Remote Engine Starter Troubleshooting Guide Page 14
INSPECTION 2/9
4 CHECK REMOTE ENGINE STARTER DIAGNOSIS
(a) Please check the diagnostic code by scan tool. (See “Diagnostic Code by Scan Tool” on page 12). If [B2334] or [B2333] is indicated, please call Fujitsu Ten Technical Support at (800) 237-5413.
(b) Connect the diagnostic connectors to enter the Diagnostic Mode. (See “Diagnostic Operation” on page 10 for the location of the connectors). If the connectors are already plugged in, please disconnect and plug them in again. (c) Check the factor to stop the engine by applying the brake in Diagnostic Mode. Hazard lights will flash in accordance with the factor of engine stop. (See “Diagnostic Factor Identification” on page 11.)
Measure the voltage and resistance of the affected terminals (listed on page 11) on the wire harness for Remote Engine Starter ECU and Accessory Gateway ECU. Then, compare measured value to specifications. (See RES ECU and Accessory Gateway ECU pin layout and terminal information from pages 4 to 6 for specifications.)
Measure the voltage and resistance of the other or all terminals on the wire harness for Remote Engine Starter ECU and Accessory gateway ECU. Then, compare measured value to specifications. (See RES ECU and Accessory Gateway ECU pin layout and terminal information from pages 4 to 6 for specifications.)
Check for continuity of the wire harness. (See Installation Instruction and Electrical Wiring Diagram.)
5-1 CHECK VEHICLE CIRCUIT (REMOTE ENGINE STARTER ECU AND ACCESSORY GATEWAY ECU INPUT/OUTPUT CHECK)
5-2 CHECK VEHICLE CIRCUIT (REMOTE ENGINE STARTER ECU AND ACCESSORY GATEWAY ECU INPUT/OUTPUT CHECK)
5-3 CHECK VEHICLE CIRCUIT (WIRE HARNESS CONTINUITY CHECK)
GO TO STEP 5-3
GO TO STEP 5-2
Number of hazard light flashes: 1 to 10
NOOK
Number of hazard light flashes: 0
GO TO STEP 5-3 NO
OK
GO TO STEP 6
CHANGE REMOTE ENGINE STARTER WIRE HARNESS
NOOK
PLEASE VERIFY THE WIRE HARNESS CONNECTIONS If they are OK: CHANGE REMOTE ENGINE STARTER ECU AND ACCESSORY GATEWAY ECU
Remote Engine Starter Troubleshooting Guide Page 15
INSPECTION 3/9
6 RETRY REGISTRATION OF IMMOBILIZER ID CODE
See Remote Engine Starter installation instructions posted on TIS for the registration method.
* Please fax “RES Replacement Authorization Request Form” and “Customer Problem Analysis Check”to (800) 438-5410 to receive an authorization number before you change the parts.
7 RETRY REMOTE ENGINE START
CHANGE REMOTE ENGINE STARTER ECU AND ACCESSORY GATEWAY ECU
NOOK
PLEASE CALL Fujitsu Ten Technical Support at (800) 237-5413
END
NOOK
Remote Engine Starter Troubleshooting Guide Page 16
INSPECTION 4/9
(a) Ignition must be “OFF” when starting this procedure.
(a) Press the UNLOCK button. (b) Confirm the doors are unlocked.
2 CHECK REMOTE ENGINE STOP OPERATION
(a) Press the UNLOCK button once. OR (b) Press and hold the LOCK button for 2 seconds.
Measure the voltage and resistance of each terminal on the wire harness for Remote Engine Starter ECU and Accessory Gateway ECU. Then, compare measured value to specifications. (See RES ECU and Accessory Gateway ECU pin layout and terminal information from pages 4 to 6 for specifications.)
ENGINE DOES NOT STOP BY REMOTE. INSPECTION PROCEDURE
1 CHECK REMOTE KEYLESS ENTRY OPERATION
3-1 CHECK VEHICLE CIRCUIT (REMOTE ENGINE STARTER ECU AND ACCESSORY GATEWAY ECU INPUT/OUTPUT CHECK)
HINT: If the engine does not stop by remote: <Vehicle with Smart entry> Press the POWER button to stop the engine. <Vehicle without Smart entry> Disconnect the Remote Engine Starter ECU connector.
GO TO VEHICLE’S REPAIR MANUAL AND CHECK REMOTE KEYLESS ENTRY OPERATION
END
NO
OK
NO
OK
GO TO STEP 3-2 NO
OK
GO TO STEP4
Remote Engine Starter Troubleshooting Guide Page 17
INSPECTION 5/9
Check for continuity of the wire harness. (See Installation Instruction and Electrical Wiring Diagram.)
4 RETRY REMOTE ENGINE STOP
* Please fax “RES Replacement Authorization Request Form” and “Customer Problem Analysis Check”to (800) 438-5410 to receive an authorization number before you change the parts.
3-2 CHECK VEHICLE CIRCUIT (WIRE HARNESS CONTINUITY CHECK)
END
OKNO
CHANGE REMOTE ENGINE STARTER WIRE HARNESS
NOOK
PLEASE VERIFY THE WIRE HARNESS CONNECTIONS If they are OK: CHANGE REMOTE ENGINE STARTER ECU AND ACCESSORY GATEWAY ECU
PLEASE CALL Fujitsu Ten Technical Support at (800) 237-5413
Remote Engine Starter Troubleshooting Guide Page 18
INSPECTION 6/9
INSPECTION PROCEDURE
1 CHECK THE REMOTE ENGINE STARTER TOTAL OPERATION TIME
(a) Ask the customer the operation time and how the customer operates the Remote Engine Starter. (b) Remote start engine and let it run for 10 minutes.
(a) Please check the diagnostic code by scan tool. (See “Diagnostic Code by Scan Tool” on page 12). If [B2334] or [B2333] is indicated, please call Fujitsu Ten Technical Support at (800) 237-5413.
(b) Connect the diagnostic connectors to enter the Diagnostic Mode. (See “Diagnostic Operation” on page 10 for the location of the connectors). If the connectors are already plugged in, please disconnect and plug them in again. (c) Check the factor to stop the engine by applying the brake in Diagnostic Mode. Hazard lights will flash in accordance with the factor of engine stop. (See “Diagnostic Factor Identification” on page 11.)
ENGINE STOPS UNEXPECTEDLY
2 CHECK REMOTE ENGINE STARTER DIAGNOSIS
HINT: EXPLAIN HOW ENGINE STARTER WORKS TO CUSTOMER:Any vehicles started with the Remote Engine Starter can idle for a total 20 minutes. Automatic engine shutdown occurs after 10 minutes, but the vehicle may be remotely started as many times as the user wishes and run for an additional 10 minutes. After 20 minutes of total operation, however, the vehicle must be started manually to reset the Remote Engine Starter.
OK
NO
END
GO TO STEP 3-1
GO TO STEP 5-2
Number of hazard light flashes: 1 to 10
Number of hazard light flashes: 0
Remote Engine Starter Troubleshooting Guide Page 19
INSPECTION 7/9
3-1 CHECK VEHICLE CIRCUIT (REMOTE ENGINE STARTER ECU AND ACCESSORY GATEWAY ECU INPUT/OUTPUT CHECK)
Measure the voltage and resistance of the affected terminals (listed on page 11) on the wire harness for Remote Engine Starter ECU and Accessory Gateway ECU. Then, compare measured value to specifications. (See RES ECU and Accessory Gateway ECU pin layout and terminal information from pages 4 to 6 for specifications.)
3-2 CHECK VEHICLE CIRCUIT (REMOTE ENGINE STARTER ECU AND ACCESSORY GATEWAY ECU INPUT/OUTPUT CHECK)
Measure the voltage and resistance of the other or all terminals on the wire harness for Remote Engine Starter ECU and Accessory gateway ECU. Then, compare measured value to specifications. (See RES ECU and Accessory Gateway ECU pin layout and terminal information from pages 4 to 6 for specifications.)
Check for continuity of the wire harness. (See Installation Instruction and Electrical Wiring Diagram.)
* Please fax “RES Replacement Authorization Request Form” and “Customer Problem Analysis Check”to (800) 438-5410 to receive an authorization number before you change the parts.
3-3 CHECK VEHICLE CIRCUIT (WIRE HARNESS CONTINUITY CHECK)
OKNO
GO TO STEP 3-3 NO
OK
PLEASE CALL (800) 237-5413.
CHANGE REMOTE ENGINE STARTER WIRE HARNESS
NO
OK
GO TO STEP 3-3
PLEASE VERIFY THE WIRE HARNESS CONNECTIONS If they are OK: CHANGE REMOTE ENGINE STARTER ECU AND ACCESSORY GATEWAY ECU
Remote Engine Starter Troubleshooting Guide Page 20
INSPECTION 8/9
FAILED REGISTRATION OF IMMOBILIZER ID CODE
INSPECTION PROCEDURE
1 CONFIRM THE PROCEDURE OF REGISTRATION
(a) See the installation instructions posted on TIS for the ID code registration process.
(b) For any assistance with the registration process, call Fujitsu Ten Technical Support at (800) 237-5413.
2 RETRY REGISTRATION OF IMMOBILIZER ID CODE
(a) VEHICLES WITH SMART ENTRY Retry registration slowly with scan tool.
(b) VEHICLES WITHOUT SMART ENTRYRetry manual registration slowly.
Measure the voltage and resistance of each terminal on the wire harness for Remote Engine Starter ECU and Accessory gateway ECU. Then, compare measured value to specifications. (See RES ECU and Accessory Gateway ECU pin layout and terminal information from pages 4 to 6 for specifications.)
3-1 CHECK VEHICLE CIRCUIT (REMOTE ENGINE STARTER ECU AND ACCESSORY GATEWAY ECU INPUT/OUTPUT CHECK)
END
END
GO TO STEP 3-1
NEXT
OK
NOOK
NO
GO TO STEP 3-2 NOOK
GO TO STEP 4
Remote Engine Starter Troubleshooting Guide Page 21
INSPECTION 9/9
Check for continuity of the wire harness. (See Installation Instruction and Electrical Wiring Diagram.)
4 RETRY REGISTRATION
* Please fax “RES Replacement Authorization Request Form” and “Customer Problem Analysis Check”to (800) 438-5410 to receive an authorization number before you change the parts.
3-2 CHECK VEHICLE CIRCUIT (WIRE HARNESS CONTINUITY CHECK)
CHANGE REMOTE ENGINE STARTER ECU AND ACCESSORY GATEWAY ECU
END
NO
OK
CHANGE REMOTE ENGINE STARTER WIRE HARNESS
NOOK
PLEASE VERIFY THE WIRE HARNESS CONNECTIONS If they are OK: CHANGE REMOTE ENGINE STARTER ECU AND ACCESSORY GATEWAY ECU
2010- LAND CRUISER TVIP V4 REMOTE ENGINE STARTER (RES) ELECTRICAL WIRING DIAGRAM (EWD)
METER
ECU-IG1
DOME 1
G1
BODY ECU
GATEWAY ECU
ENGINE CONTROL MODULE
B4
B3
C8 J3
IG1
RE
LAY
D8 K3
M1
N1
E17 E8 E4E16
REMOTE ENGINE STARTER ECU
E9E6 E1 E12E11
F2
F4
H2H1
F1
F5 F3
W-R
W-B
W-R
W-R
V R
RV
L R
RR
G
G
G RR
RLR G
W-B
W-B W-B W-B Y
W-B
W-B W-B
RR
R
Splice Connection (Splicing Connector)
TVIP or Vehicle Terminal Insert
VehicleConnector
Connector to Connector
TVIP Harness
Vehicle Harness
2009- LAND CRUISER TVIP V4 REMOTE ENGINE STARTER (RES) ELECTRICAL WIRING DIAGRAM(EWD)
LH-IG
BAT
TER
YA
LTE
R
SH
OR
T P
IN LH-J
/B
A3
R
A4
W-R
E6 E6
FE6 IE2
FE6
Draft1: 03/23/09PT398-60080(for wire harness part no. PT398-60090-RS (297140-50410121))
IE2
2010- LAND CRUISER TVIP V4 REMOTE ENGINE STARTER (RES) CONNECTORS
2009- LAND CRUISER TVIP V4 REMOTE ENGINE STARTER (RES) CONNECTORS
(MALE PIN)
(FEMALE PIN)
(FEMALE PIN)
(MALE PIN)
(MALE PIN)
1 1
(FEMALE PIN)
KJ M N
HG
DC
7 4 3 112010
212
81819
43 7 20
10
11 818
212 19
12
(MALE PIN)(FEMALE PIN)
F
1 2 3 4 5
1
(TERMINAL PIN)
45 23
910 78 62 43
76 98
5
10
9 66 9
(FEMALE PIN)
E
1 94 6 811 16 1711 12
3 4
(FEMALE PIN)
4 3
(MALE PIN)
A B
Draft1: 03/23/09PT398-60080(for wire harness part no. PT398-60090-RS (297140-50410121))
TOYOTA LAND CRUISER 2013 - TVIP V4 Preparation REMOTE ENGINE STARTER (RES)
Page 1 of 26 pages Issue B: 12/21/12
Part Number: PT398-60140
Conflicts Will not program with Techstream Lite.
Recommended Sequence of Application Item # Accessory 1 XM XM Radio 2 TVIP V2 Glass Breakage Sensor (GBS)
and/or V4 Remote Engine Starter (RES)
Kit Contents Item # Quantity Description 1 1 Wire Harness 2 1 RES ECU Bracket 3 1 Extra Large Wire Tie
Hardware Bag Contents Item # Quantity Description 1 1 RES ECU 2 1 Gateway ECU 3 1 Gateway ECU Bracket 4 1 M6 Tapping Screw 5 15 Wire Ties 6 1 Waterproof Sheet 7 2 Large Foam Tape (1sheet - 2pcs) 8 1 Custom Double Stick Tape 9 2 Key Tag (English) 10 2 Window Labels (English) 11 2 Transmitter Labels (English) 12 1 Engine Room Warning Label (English)
13 2 Key Tag (Spanish) 14 2 Window Labels (Spanish) 15 2 Transmitter Labels (Spanish) 16 1 Engine Room Warning Label (Spanish)
17 1 Owner’s Guide
Additional Items Required For Installation Item # Quantity Description 1 1 Black Electrical Tape
Recommended Tools Personal & Vehicle Protection Notes
Safety Glasses Safety Gloves (Optional) Vehicle Protection Blankets, Parts Boxes Special Tools Notes Techstream Do not use Techstream Lite Installation Tools Notes Screwdriver #2 Phillips
Nylon Panel Removal Tool e.g. Panel Pry Tool #1 Toyota SST # 00002-06001-01
Side Cutters
Torque Wrench 36 in•lbf (4.07 N•m) 88.5 in•lbf (10 N•m)
Utility Knife Pliers Clip Clamp Pliers Tape Clear Wrench 10mm Socket 10mm, Extension, 10mm Deep
Special Chemicals Notes Cleaner VDC Approved Cleaner Glass Cleaner Household Glass Cleaner
Legend
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation.
These guidelines can be found in the "Accessory Installation Practices" document.
This document covers such items as: Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.) Safety (eye protection, rechecking torque procedure, etc.) Vehicle Disassembly/Reassembly (panel removal, part storage, etc.) Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.)
Please see your Toyota dealer for a copy of this document.
STOP: Damage to the vehicle may occur. Do not proceed until process has been complied with.
OPERATOR SAFETY: Use caution to avoid risk of injury.
CAUTION: A process that must be carefully observed in order to reduce the risk of damage to the accessory/vehicle and to ensure a quality installation.
TOOLS & EQUIPMENT: Used in Figures calls out the specific tools and equipment recommended for this process.
REVISION MARK: This mark highlights a change in installation with respect to previous issue.
SAFETY TORQUE: This mark indicates that torque is related to safety.
TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES)
Page 2 of 26 pages Issue B: 12/21/12
Des
crip
tion
5P W
HIT
E
5P W
HIT
E
10P
WH
ITE
10P
WH
ITE
20P
WH
ITE
fo
r R
ES
EC
U
5P W
HIT
E
for
Gat
eway
EC
U
GR
OU
ND
WIR
E
TE
RM
INA
L
2P W
HIT
E
Gat
eway
EC
U
20P
BL
UE
20P
BL
UE
RE
S E
CU
1P W
HIT
E
(RE
S D
iagn
osis
)
1P W
HIT
E
(RE
S D
iagn
osis
)
Veh
icle
– – – – – – – – – – – – – –
TV
IP
A
B
C
D
E F G
H I J K
L
M
N
TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES)
Page 3 of 26 pages Issue B: 12/21/12
1. Vehicle Disassembly.
(a) Place the Vehicle in Park with the Parking
Brake set.
(b) Remove the Negative Battery Cable.
(Fig. 1-1)
(1) Protect the Fender before starting.
(2) Note the Battery Cable position, as it will be re-installed in the same position.
CAUTION: Do not touch the positive terminal.
1 Glove Box Under Cover
2 PS Dash Side Cover
3 PS Step Cover
4 PS Cowl Cover
5 PS Knee Panel
6 PS Cluster Side Panel
7 PS Knee Airbag
8 Glove Box
9 DVD Unit
10mm Socket NegativeBatteryCable
Fig. 1-1
Fig. 1-2
Fig. 1-2
Remove all corresponding connectors accordingly as you disassemble.
TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES)
Page 4 of 26 pages Issue B: 12/21/12
(c) Remove the Glove Box Under Cover.
(Fig. 1-3)
(1) Begin by protecting the Vehicle Interior with Blankets.
(d) Remove the Passenger’s Side Dash Side.
Cover. (Fig. 1-4)
(e) Remove the Passenger’s Side Step Cover.
(Fig. 1-5)
(f) Remove the Passenger’s Side Cowl Cover.
(Fig. 1-6)
(1) Remove 1 Nut.
Fig. 1-5 Step Cover
Nylon Panel Removal Tool
Fig. 1-4
Dash Side Cover
Nylon Panel Removal Tool
Fig. 1-6
Nut
Cowl Cover
Nylon Panel Removal Tool
Fig. 1-3
Nylon Panel Removal Tool
Glove Box Under Cover
TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES)
Page 5 of 26 pages Issue B: 12/21/12
(g) Remove the Passenger’s Side Knee Panel.
(Fig. 1-7)
(h) Remove the Passenger’s Side Cluster Side
Panel. (Fig. 1-8)
(1) Remove 1 Screw and 1 Clip.
(i) Remove the Passenger’s Knee Air Bag.
(Fig. 1-9)
(1) Remove 4 Bolts.
(2) Do not disconnect the Vehicle’s Connector.
CAUTION: Sharp metal edges.
(j) Wrap the Passenger’s Knee Air Bag in a
Blanket and use the TVIP Kit Box to support
it. (Fig. 1-10)
CAUTION: Sharp metal edges.
Fig. 1-7
Knee Panel
Nylon Panel Removal Tool
Fig. 1-8
Cluster Side Panel
Screw
Clip
Phillips Screwdriver, Nylon Panel Removal Tool
Fig. 1-10
Knee Air Bag
TVIP Box Fig. 1-10
Knee Air Bag
TVIP Box
Fig. 1-9
Bolts (x2)
Knee Air Bag
10mm Socket, Nylon Panel Removal Tool
Bolts (x2)
TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES)
Page 6 of 26 pages Issue B: 12/21/12
(k) Remove 2 Screws from the bottom of the
Glove Box. (Fig. 1-11)
(l) Open the Glove Box, remove 2 Bolt Covers
from the Glove Box. (Fig. 1-12)
(m) Dislodge the Glove Box (Fig. 1-12)
(1) Remove 2 Bolts.
NOTE: Pull down and out to avoid damaging the Vehicle Clips or Dash Trim.
(n) Remove the Vehicle Harness from the
backside of the Glove Box, remove the
Glove Box. (Fig. 1-13)
(1) Disconnect any Connectors.
(o) Temporarily install the Passenger's Side
Knee Air Bag. (Fig. 1-14)
CAUTION: Sharp metal edges.
Fig. 1-11 Screws (x2)
Phillips Screwdriver
Fig. 1-12
Nylon Panel Removal Tool, 10mm Socket
Cover
Bolt
Cover
Bolt
Glove Box
Fig. 1-13
Vehicle Harness
Glove Box (backside)
Fig. 1-14
10mm Socket
Bolts (x2) Bolts (x2)
Knee Air Bag
TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES)
Page 7 of 26 pages Issue B: 12/21/12
VEHICLES EQUIPPED WITH NAVIGATION SYSTEM.
(p) Remove the DVD Unit from the Glove Box
Area. (Fig. 1-15)
(1) Remove 2 Screws and 1 Nut.
(2) Using the Clip Clamp Tool or the like, push on the inside the Vehicle Clamp, and release it from the DVD Unit.
2. V4 Wire Harness Installation.
(a) Route the V4 Harness behind the
Vehicle Brace and Yellow Harness in the
Glove Box area as shown. (Fig. 2-1)
CAUTION: Sharp metal edges.
(b) Secure the V4 Harness's White Taped
Marker to the Reinforcement with 1 Wire
Tie. (Fig. 2-2)
(c) Secure the V4 Harness to the Reinforcement
with 2 Wire Ties.
(Fig. 2-2)
(d) Locate and remove 1 Bolt from the Vehicle
Ground Terminal in the upper left side of the
Glove Box Area. (Fig. 2-3)
(1) Do not discard the Bolt.
Fig. 2-3
Bolt
Vehicle’s Ground Terminal10mm Socket
V4 Harness’s Ground Terminal
Fig. 1-15
10mm Deep Socket, Clip Clamp Pliers, Screwdriver
Nut Screw
Screw
DVD Unit
Clamp
Side Cutter
Fig. 2-2 5P
V4 Harness V4 Harness’ White Tape
Marker
Wire Ties (x3)
Fig. 2-1 Vehicle’s Yellow Harness
Brace
V4 Harness
V4 Harness
White Tape
TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES)
Page 8 of 26 pages Issue B: 12/21/12
(e) Use the existing Vehicle's Bolt to secure the
V4 Harness's Ground Terminal with the
Vehicle's Ground Terminal. (Fig. 2-4)
(1) Make sure that the Vehicle's Ground Terminal Pin seats properly.
(f) Locate and remove the Vehicle's White 10P
Connector from the Connector Block in the
Glove Box Area. (Fig. 2-5)
(g) Plug in the V4 Harness’s White 10P
Connectors in between the Vehicle
Harness’s White 10P Connector and the
Connector Block. (Fig. 2-6)
(1) Verify secure connection.
(h) Push the 10P Connectors through the
opening between the Vehicle Harness and
the Passenger's Side Connector Block as
shown. (Fig. 2-7)
Fig. 2-4
Vehicle's Ground
Terminal
Bolt
10mm Socket V4 Harness's Ground Terminal
Fig. 2-5 Passenger's Side Connector Block
Vehicle’s 10P (White)
Fig. 2-6
V4 Harness' White 10P
V4 Harness
Vehicle Harness' White 10P
Passenger's Side Connector Block
V4 Harness' White 10P
Fig. 2-7
Vehicle Harness
V4 Harness
Passenger's Side Connector Block
10P
TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES)
Page 9 of 26 pages Issue B: 12/21/12
(i) Secure the 10P Connectors to the Vehicle
Harness with 1 Wire Tie. (Fig. 2-8)
(j) Secure the V4 Harness to the Vehicle
Harness behind the Passenger's Side
Connector Block with 1 Wire Tie.
(Fig. 2-8)
(k) Wrap the V4 Harness’s branch area with 1
Large Foam Tape as shown. (Fig. 2-9)
(l) Route the V4 Harness's White 20P
Connector toward the Vehicle's Floor.
(Fig. 2-9)
3. RES ECU Preparation and Installation.
(a) Remove the Clear Protective Sheet from
the Double Stick Tape and attach it to
the Part Number Label side of the RES
ECU as shown. (Fig. 3-1)
(1) Be sure to apply the Clear Sheet side on the RES ECU.
(2) Be sure to attach adhesive tape on the part number label side of the RES ECU.
(3) Do not cover the Part Number Label with the adhesive tape.
CAUTION: Do not touch the adhesive surface.
Fig. 2-8
10P Connectors
V4 Harness
Side Cutter
Wire Tie
Vehicle Harness
Wire Tie
Vehicle Harness
Fig. 3-1 RES ECU
Double-Side Adhesive Tape
Part Number Label
Yellow Sheet (Vehicle Side)
Clear Sheet (RES ECU Side)
Fig. 2-9
V4 Harness
V4 20P (White)
Large Foam Tape
TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES)
Page 10 of 26 pages Issue B: 12/21/12
(b) Remove the Backing Sheet of 1 Waterproof
Sheet and attach it to the RES ECU near the
connectors as shown. (Fig. 3-2)
CAUTION: Do not touch the adhesive surface.
(c) Insert the RES ECU Bracket into the
indicated Bracket Slots on the RES ECU.
(Fig. 3-3)
(1) Ensure the Bracket is firmly attached to the ECU.
(d) Apply 1 strip of Large Foam Tape to the
RES ECU as shown. (Fig. 3-4)
(e) Turn over the Floor Carpet on the left side of
the Passenger's Side Area. (Fig. 3-5)
(f) Pull back the Felt on the backside of the
Floor Carpet as shown. (Fig. 3-5)
(1) Do not remove or cut off the Felt.
Fig. 3-3 RES ECU
RES ECU Bracket
Fig. 3-5
Felt
Floor Carpet
Fig. 3-4 RES ECU
Large Foam Tape
Fig. 3-2
Waterproof Sheet
RES ECU
TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES)
Page 11 of 26 pages Issue B: 12/21/12
(g) Connect the V4 Harness's White 20P
Connector to the RES ECU. (Fig. 3-6)
(h) Using the VDC approved cleaner and
Cleaning Method, clean the area indicated
on the left side of the Passenger’s Side Floor.
(Fig. 3-6)
(i) Remove the Protective Sheet of the Double
Stick Tape. (Fig. 3-6)
(j) Center the RES ECU Bracket to Vehicle's
Bolt as shown. Then press the RES ECU
firmly to the Vehicle. (Fig. 3-6)
(1) Do not attempt to reposition the ECU once placed.
(k) Run 1 Extra Large Wire Tie through the
RES ECU rectangular hole and behind the
Vehicle Brace and secure it. (Fig. 3-7)
(1) Do not tighten the Wire Tie, it should hang freely.
(l) Secure the V4 Harness to the side of the
inside Vehicle Brace with 1 Wire Tie as
shown. (Fig. 3-8)
(1) Do not use the front hole of the Vehicle Brace.
Fig. 3-6
Bolt
20P
V4 Harness
RES ECU
Portion of the Protective Bracket
Floor Carpet
Fig. 3-7
Side Cutter
V4 Harness
RES ECU
Vehicle’s Brace
ECU Bracket’s Rectangular Hole
Extra Large Wire Tie
Wire TieSide Cutter
V4 Harness
RES ECU
Vehicle’s Brace
Hole
Fig. 3-8
TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES)
Page 12 of 26 pages Issue B: 12/21/12
(m) Attach 1 Large Foam Tape to the Vehicle’s
Brace and the V4 Harness as shown. then
put the Carpet back. (Fig. 3-9)
GO BACK TO THE V4 HARNESS’S WHITE TAPE MARKER AREA.
4. Gateway ECU Preparation and Installation.
(a) Insert the Gateway ECU Bracket into the
indicated Bracket Slots on the Gateway
ECU. (Fig. 4-1)
(1) Ensure the Bracket is firmly attached to the ECU.
(b) Connect the V4 Harness's White 5P
Connector to the Gateway ECU. (Fig. 4-2)
(1) Verify secure connection.
(c) Using the M6 Tapping Screw from the Kit,
install the Gateway ECU Bracket. (Fig. 4-2)
(1) Make sure that the Bracket Pin seats properly.
CAUTION: Do not crimp the V4 and/or the V2 Harness between the Gateway ECU Bracket and the Vehicle Reinforcement Brace.
Fig. 3-9
RES ECU
Carpet
Large Foam Tape
Vehicle’s Brace
Fig. 4-1
Connector
Gateway ECU
Gateway ECU Bracket
Fig. 4-2
10mm Socket
Gateway ECU
5P
Tapping Screw
V4 Harness
Pin
Hole
TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES)
Page 13 of 26 pages Issue B: 12/21/12
5. V4 Wire Harness Installation (continued).
(a) Route the V4 Harness behind the Vehicle
Brace and ECU Brackets as shown.
(b) Secure the V4 Harness to the Vehicle Brace
with 1 Wire Tie. (Fig. 5-1)
(c) Locate the Vehicle’s 5P White Connectors.
(Fig. 5-2)
(d) Disconnect the Vehicle’s 5P White
Connectors. (Fig. 5-2)
(e) Connect the V4 5P Connectors in between
the Vehicle’s 5P Connectors. (Fig. 5-3)
(f) Secure the V4 Harness to the Vehicle
Harness with 1 Wire Tie. (Fig. 5-4)
(g) Secure the 5P Connectors to the Vehicle
Harness with 1 Wire Tie. (Fig. 5-4)
Fig. 5-2
Fig. 5-3
Fig. 5-4
Side Cutter
Fig. 5-1
Side Cutter
Wire Tie
TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES)
Page 14 of 26 pages Issue B: 12/21/12
(h) Locate the Vehicle’s 2P Pre-Connector.
(Fig. 5-5)
(i) Remove the Break Away Tape from the
Connector. (Fig. 5-5)
(j) Connect the V4 2P Connector to the
Vehicle’s 2P Pre-Connector. (Fig. 5-6)
(k) Secure the 2P Connectors to the Vehicle
Harness with 1 Wire Tie. (Fig. 5-7)
(l) Route the remaining V4 Harness along the
Vehicle Harness towards the Passenger’s
Cowl Area. (Fig. 5-8)
(m) Secure the V4 Harness to the Vehicle
Harness using 1 Wire Tie. (Fig. 5-8)
Fig. 5-6
Fig. 5-5
2P Pre-Connector
Fig. 5-7
Side Cutter
Fig. 5-8
Side Cutter
TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES)
Page 15 of 26 pages Issue B: 12/21/12
(n) Route the remaining V4 Harness as shown.
(Fig.5-9)
CAUTION: Do not secure the V4 1P RES Diagnostic Connectors.
(o) Secure the V4 Harness to the Vehicle
Harness with 1 Wire Tie. (Fig. 5-9)
(p) Disconnect the Vehicle’s Blue 20P
Connector from the Passenger’s Side
Cowl Area. (Fig. 5-10)
(q) Connect the V4 20P Connectors in between
the Vehicle’s 20P Connectors. (Fig. 5-11)
(r) Secure the 20P Connectors to the Vehicle
Harness with 1 Wire Tie. (Fig. 5-12)
Fig. 5-10
Fig. 5-11
Fig. 5-9
Side Cutter
Fig. 5-12
Side Cutter
TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES)
Page 16 of 26 pages Issue B: 12/21/12
6. Partial Reassembly.
(a) Reassemble the Vehicle, except for the
Passenger's Cowl Cover, and Step
Cover.
(1) Reconnect any disconnected connectors.
(2) Torque the Passenger’s Knee Air Bag to 88.5 in•lbf (10 N•m).
(b) Verify the Short Pin is installed. (Fig. 6-1)
(1) If not, install the Short Pin.
7. Registration Process.
(a) Open the Hood. (Fig. 7-1)
Note: Do not close the Hood during the Registration Setting Procedure. (Steps b-cc)
(b) Temporarily reconnect the Vehicle's
Negative Battery Cable. (Fig. 7-2)
CAUTION: Do not touch the positive terminal.
(c) Locate the V4 Harness’s 1P RES Diagnostic
Connectors in the Passenger’s Side Cowl
Area, and remove the Tape.
(Fig. 7-3)
(d) Connect the 2 RES Diagnostic Connectors.
(Fig. 7-3)
Fig. 6-1 Install Short Pin
Fig. 7-1
EXAMPLE
Fig. 7-3
RES Diagnostic 1P
Connectors V4 Harness
Fig. 7-2
Negative Battery Cable
Battery
TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES)
Page 17 of 26 pages Issue B: 12/21/12
(e) Ensure all Doors are closed and the Smart
Key is in your possession. (Fig. 7-4)
(f) Cycle the Vehicle’s “Engine Start
Stop“ Button from “OFF” to “ON” 5 times.
(Fig. 7-4)
(1) Place the Shift Lever in the "P" Position.
NOTE: One cycle consists of:
OFFAccessoryON
This is equivalent to pressing the “Engine
Start Stop” Button 14 times.
(g) Once the fifth cycle has been completed, the
Hazard Lights Flash once. (Fig. 7-4)
(h) Press the Vehicle’s “Engine Start Stop”
Button once more to turn the ignition to
OFF.
(i) Start the Engine, after 10 seconds stop the
Engine. (Fig. 7-5)
(j) The Hazard Lights flash once. (Fig. 7-5)
Go to step m.
(k) If this procedure failed, the Hazard Lights
flash twice.
(l) Disconnect the RES Harness White 1P
Connectors from the Passenger’s Side Cowl
Area. (Fig. 7-6)
Start again from step d.
Fig. 7-6
RES Diagnostic 1P Connectors
Fig. 7-4
EXAMPLE
Fig. 7-5
EXAMPLE SUCCESS
TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES)
Page 18 of 26 pages Issue B: 12/21/12
CAUTION: Techstream Lite will not work for this section, use the Techstream Notebook ONLY.
(m) Connect the Techstream
Notebook to the Vehicle’s
Diagnostic Port. (Fig. 7-7)
(n) With the Remote Control Key in
your possession, press the
Vehicle’s “Engine Start Stop”
Button twice to select the
Ignition “ON” position.
Note: Do not apply Brake Pedal.
(o) Start the TIS Techstream
Application by clicking on the
shortcut located on the Desktop.
(p) Click “Connect to Vehicle.”
(Fig. 7-8)
(q) Confirm that the information
displayed on the Vehicle
Connection Wizard is correct for
the Vehicle. If not verify that the
Techstream is properly
connected. (Fig. 7-9)
(r) Under Option, select “Others”
then Click “Next>.” (Fig. 7-9)
Fig. 7-7
Vehicle Diagnostic Port
Techstream Notebook
Fig. 7-8
Fig. 7-9
Others
TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES)
Page 19 of 26 pages Issue B: 12/21/12
(s) Select “Smart Access.”
(Fig. 7-10)
(t) Click . (Fig. 7-10)
(u) Click on “Utility.” (Fig. 7-11)
(v) Select “ECU Communication ID
Registration.” (Fig. 7-11)
(w) Click . (Fig. 7-11)
(x) Confirm that the Engine is ON
(IG), and that the Smart Cancel
Function is OFF. (Fig. 7-12)
(y) Click “Next>” to continue.
(Fig. 7-12)
Fig. 7-11
Fig. 7-12
Fig. 7-10
TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES)
Page 20 of 26 pages Issue B: 12/21/12
(z) Select “Remote Engine Starter.”
(Fig. 7-13)
(aa) Click “Next>” to continue.
(Fig. 7-13)
(bb) Click “Exit.” (Fig. 7-14)
(cc) Click . (Fig. 7-15)
Fig. 7-13
Fig. 7-14
Fig. 7-15 Example
TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES)
Page 21 of 26 pages Issue B: 12/21/12
(dd) Close the Hood. (Fig. 7-16)
(ee) The Hazard Lights flash twice. Registration
is completed (Fig. 7-16)
If this procedure failed, the Hazard Lights flash 3 times. Registration was not set.
Disconnect the 1P RES Diagnostic Connectors, then open the Hood.
Start again from Step d.
(ff) Disconnect the V4 Harness's 1P RES
Diagnostic Connectors. (Fig. 7-17)
(gg) Secure the V4 Harness and 1P Connectors
with Electrical Tape as shown. (Fig. 7-17)
(hh) Secure the V4 Harness to the Vehicle
Harness with the Electrical Tape as
shown. (Fig. 7-17)
(ii) Press the Vehicle’s “Engine Start Stop”
Button to place the Vehicle in the "OFF"
(Indicator Light off) position.
Fig. 7-16
EXAMPLE
V4 Diagnostic 1P Connectors
Fig. 7-17
Electrical Tape
TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES)
Page 22 of 26 pages Issue B: 12/21/12
8. Tags and Label Installation.
● For US Vehicles use the English Labels and discard the Spanish Labels.
● For Mexico Vehicles use the Mexico Labels, and discard the English Labels.
(a) Remove 2 of the Remote Controls from their
protective bag.
(1) Use a utility knife, to cut a slit in each bag.
(b) Using VDC approved cleaner and Cleaning
Method, clean the area indicated on the
Remote Controls. (Fig. 8-1)
(c) Attach the Key Label to the Remote
Controls as shown. (Fig. 8-1)
(1) Use a piece of the clean adhesive tape to lift the labels off their protective backing.
CAUTION: Do not touch the adhesive surface.
(d) Attach the Remote Engine Starter Tags to
the Vehicle Remote Controls. (Fig. 8-2)
(e) Using VDC approved cleaner and Cleaning
Method, clean the area indicated on the
Engine Compartment Cover.(Fig. 8-3)
(f) Attach the Warning Label to the Engine
Compartment Cover as shown. (Fig. 8-3)
CAUTION: Do not touch the adhesive surface.
Fig. 8-2
Key Tag
Fig. 8-1
Utility Knife, Clear Tape
Key Label
2mm 2mmKey
Label
3 Button Key4 Button Key
Fig. 8-3
Clear Tape
TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES)
Page 23 of 26 pages Issue B: 12/21/12
(g) Use Household Glass Cleaner to clean the
inside of the Front Door Window. (Fig. 8-4)
(h) Use a piece of Clear Tape to lift the Label
off its protective backing.
CAUTION: Do not touch the adhesive surface.
(i) Attach the Label as shown. (Fig. 8-4)
NOTE: Make sure to Align according to Etching or Other Label. (Fig. 8-4)
REPEAT: steps g–i with the other Window.
9. Completing the Installation.
(a) Cut and apply ⅓ piece of Large Foam Tape
to the backside of the Glove Box. (Fig.
9-1)
(b) Complete the reassembly of the Vehicle.
(1) Verify the Panels fit together properly, with no uneven gaps.
(c) Position the Negative Battery Cable at the
original factory position. (Fig. 9-2)
(1) Tighten the Nut to 36 in•lbf (4.07 N•m)
CAUTION: Do not touch the positive terminal.
(d) Clean up and remove any Trash.
(e) Sealed in its protective Bag, place the
Owner’s Guide in the Glove Box.
(f) Reset the power windows.
(1) Press the Power Button to select the Ignition “ON” position.
(2) Push down on the Power Window Switches lowering the windows halfway.
(3) Pull up on the switches until the windows close
(4) Continue holding up on the Switches for a minimum of 1 second.
Fig. 9-2
Negative Battery Cable
Torque Wrench
Battery
Fig. 9-1
⅓Foam Tape
Glove Box (backside)Utility Knife Large Foam Tape
Molding
Etching
Etching
Molding
Clear Tape
Fig. 8-4
TOYOTA LAND CRUISER 2013 – TVIP V4CHECKLIST – These points MUST be checked to ensure a quality installation. REMOTE ENGINE STARTER (RES)
Issue B: 12/21/12
Accessory Function Checks
Close the hood, enter the vehicle and close all doors. Place the shift lever in the “P” (Park) position, set the parking brake and make sure the Vehicle is off.
Perform Look For
1 Press the remote control’s lock button twice within 2 seconds, then press and hold the lock button for 3 seconds.
The hazard lights flash after 3 seconds. The engine starts. The hazard lights flash repeatedly for 20 seconds.
2 With the engine running, pull the hood release handle. NOTE: Some Vehicles may require you to exit the Vehicle and pull up on the Hood.
The engine stops. The hazard lights flash once. The security alarm triggers (only if equipped with OE Factory Alarm, not Genuine Accessory alarm, and only if armed)
3 Move the shift lever out of “P” (Park). Attempt to start the Vehicle using the remote.
The engine does not start.
Vehicle Appearance Check
Perform Look For
□ After accessory installation and removal of protective cover(s), perform a visual inspection of the vehicle.
Ensure no damage (including scuffs and scratches) was caused during the installation process.
(For PPO installations, refer to TMS Accessory Quality Shipping Standard.)
Page 24 of 26 pages
TOYOTA LAND CRUISER 2013 - TVIP V4 Checklist - these points MUST be checked to ensure a quality installation. REMOTE ENGINE STARTER (RES)
Page 25 of 26 pages Issue B: 12/21/12
Vehicle Function Check
Function Function
□ Head Light □ ABS Light (if equipped) If the warning light remains on, it may indicate a system malfunction.
□ High Beams □ Rear Wiper/Washer (if equipped)
□ Turn Signal Lights □ Clock (if equipped)
□ Tail Lights □ Accessory Power Socket (if equipped)
□ Stop Lights □ Starter
□ Backup Lights □ Audio/Video (if equipped)
□ Hazard Lights □ Power Sliding Door (if equipped)
□ Marker Lights □ Convenience Memory Settings (if equipped)
□ Dome/Courtesy Lights □ Heated Seats (if equipped)
□ Panel/Switch Illumination □ Massage Seats (if equipped)
□ Accessory Controls/Illumination (if equipped) □ Rear Window Defogger (if equipped)
□ Key Sensor Buzzer □ Power Side Mirrors (if equipped)
□ Fog Lights (if equipped) □ Side Mirror Defogger (if equipped)
□ Daytime Running Lights (if equipped)
□ Front Windshield Defogger (if equipped)
□ Trunk/Tailgate/Bed Lights (if equipped)
□ Navigation System (if equipped)
□ Glove Box Light (if equipped) □ Rear Sunshade (if equipped)
□ Cruise Control Light (if equipped) □ Steering Wheel Audio Control (if equipped)
□ Seat Belt Warning Light If the warning light remains on, it may indicate a system malfunction.
□ Steering Wheel Column Adjusts Without Interference
TOYOTA LAND CRUISER 2013 - TVIP V4 Checklist - these points MUST be checked to ensure a quality installation. REMOTE ENGINE STARTER (RES)
Page 26 of 26 pages Issue B: 12/21/12
Remove the short pin after Function check. Check with your Port/Dealer to see if this step is necessary.
Function Function
□ Air Bag Warning Light If the warning light remains on, it may indicate a system malfunction.
□ Lamp Failure Sensor If the warning light remains on, it may indicate a system malfunction.
□ Track/Skid Control Light (if equipped) If the warning light remains on, it may indicate a system malfunction.
□ Front Wiper/Washer
□ HVAC □ Hood Latch Release
□ Power Locks (if equipped) □ Passenger Air Bag Switch (if equipped)
□ Power Windows (if equipped) □ Rollover Side Curtain Air Bag Switch (RSCA) (if equipped)
□ Power Seats (if equipped) □ Tire Pressure Monitoring System (TPMS) (if equipped)
Prior to TPMS activation and Pre-delivery Service (PDS) of the Vehicle the TPMS light will blink when IG is turned on.
After TPMS activation and PDS of the Vehicle the TPMS light will illuminate for a few seconds and go off when IG is turned on.
□ Horn
□ Gauges
□ Power Sunroof (if equipped)
Store Short Pin Here
Side Cutter