Lastec Deck Kit 100EZT
Parts ManualManual Part #: Man-100EZT
LASTEC7865 N County Road 100E
Lizton, Indiana 46149
Phone (317) 892-4444 Fax (317) 892-4188 www.lastec.com
8 Lastec, 2009
Printed in the United States of America, all rights reserved. No part of this manual may be reproduced in any form by any photographic, electronic, mechanical or other means or used in any information storage and retrieval system without written permission from
Lastec, Inc.7865 N. County Road 100E
Lizton, IN 46149
Table of Contents Section-Page
SECTION 1 GENERAL INFORMATION 1-1
1.1 How To Use The Parts List ....................................................................................... 1-21.2 Torque Values ........................................................................................................... 1-31.3 Decal Locations ......................................................................................................... 1-41.4 Belts and Decks ......................................................................................................... 1-61.5 Rear Guard................................................................................................................. 1-81.6 Mulching Dam Kit................................................................................................... 1-10
SECTION 2 MOUNTING HARDWARE 2-1
2.1 Mounting Hardware................................................................................................... 2-22.2 Mounting Frame ........................................................................................................ 2-42.3 Front Axle.................................................................................................................. 2-62.4 Foot Lift Valves......................................................................................................... 2-82.5 Footpan Assembly ................................................................................................... 2-10
SECTION 3 DRIVE SYSTEM 3-1
3.1 Gearbox Tensioner .................................................................................................... 3-23.2 Gearbox Assembly .................................................................................................... 3-4
3 Lastec//080216 Table of Contents
Table of Contents Section-Page
SECTION 4 MOWER DECKS 4-1
4.1 Deck 1 Hardware....................................................................................................... 4-24.2 Double Pulley Spindle, Decks 1, 5 (Serial #46331112 and later) ............................. 4-44.3 Spindle Housing, Decks 1, 2, 4 and 5 (Serial #46331112 and later)......................... 4-64.4 Spindle Assembly, Deck 1 & 5 (Prior to Serial #46331112) .................................... 4-84.5 Spindle Housing(Prior to Serial #46331112) .......................................................... 4-104.6 Decks 1 and 5 Rocker Assembly............................................................................. 4-124.7 9” Wheel Yoke Assembly ....................................................................................... 4-144.8 9” x 3.5” Wheel Assembly, Solid............................................................................ 4-164.9 Rocker Rod Assembly............................................................................................. 4-184.10 Deck 1 Idler Assembly ............................................................................................ 4-204.11 Anti-Scalp Roller Assembly (Optional) .................................................................. 4-224.12 Deck 2 Hardware..................................................................................................... 4-244.13 Deck 2 Covers ......................................................................................................... 4-264.14 Double Pulley Spindle, Decks 2, 4 (Serial #46331112 and later) ........................... 4-284.15 Spindle Assembly, Deck 2 & 4 (Prior to Serial #46331112) .................................. 4-304.16 Deck 3 Hardware..................................................................................................... 4-324.17 Single Pulley Spindle, Decks 3 (Serial #46331112 and later)................................. 4-344.18 Spindle Assembly, Deck 3 (Prior to Serial #46331112) ......................................... 4-364.19 Spindle Housings, Deck 3 (Prior to Serial #46331112) .......................................... 4-384.20 Anti-Scalp Rollers ................................................................................................... 4-404.21 Pull Pivot Assembly ................................................................................................ 4-424.22 Deck 3 Rod Assembly ............................................................................................. 4-444.23 Grass Discharge Deck 3 .......................................................................................... 4-464.24 Deck 4 Hardware..................................................................................................... 4-484.25 Deck 4 Covers ......................................................................................................... 4-504.26 Deck 5 Hardware..................................................................................................... 4-524.27 Deck 5 Idler ............................................................................................................. 4-544.28 Rear Grass Discharge Deck 5.................................................................................. 4-564.29 Deck Wheel Assembly ............................................................................................ 4-584.30 Rear Wheel Hanger Assembly (Optional)............................................................... 4-604.31 Wheel Lift Rod Assembly ....................................................................................... 4-624.32 Wheel Yoke Assembly ............................................................................................ 4-644.33 Deck Lift Cylinder Assembly.................................................................................. 4-664.34 Hydraulic Hoses ...................................................................................................... 4-68
SECTION 5 INDEX 5-1
Table of Contents Lastec//080216 4
Mower//080216 1-1
1
SECTION 1 GENERAL INFORMATION
General InformationHow To Use The Parts List1
1-2 Mower//080216 General Information
1.1 How To Use The Parts List
Use the table of contents or part number index to locate the part you need.
Go to the appropriate section and locate the part in the table and illustration.
Parts shown indented under another part are included with that part. IMPORTANT:Assemblies marked with a diamond () are non-saleable and all the parts shown as included need to be purchased separately.
See the sample table below. Sample Assembly A01111 includes part F02222-22 and sub-assembly A03333. The diamond () indicates that assembly A01111 is non-saleable and all the parts shown as included need to be purchased separately. Subassembly A03333 includes parts S04444-4 and F07777-77. The diamond () indicates that subassembly A03333 is non-saleable and all the parts shown as included need to be purchased sepa-rately.
To Order Parts:
From the continental U.S., call your local Lastec distributor to order parts. If there is no Lastec distributor in your area, call 1-800-515-6798. Have your customer num-ber, unit serial number, and part numbers ready when you call.
From other international locations, contact the Lastec distributor in your area for parts.
REF PART # DESCRIPTION (Indicates Non-Saleable Items) COMMENTS QTY.
A01111 Sample Assembly 1
1 F02222-22 Sample Part 1
A03333 Sample Subassembly 1
2 S04444-4 Sample Part 1
3 F07777-77 Sample Part 1
General InformationTorque Values
General Information Mower//080216 1-3
1
1.2 Torque Values
Below is a table of suggested torque values for this unit. Please use these torque values
on this unit unless otherwise specified.
Grade Units SAE 5 SAE 8
Tensile
Strength
105000
PSI150000
PSI
Grade Mark
Bolt
Dia.
Threads.
Per In.Units SAE 5 SAE 8
6
8
10
10
12
1/4
1/4
5/16
5/16
3/8
3/8
7/16
7/16
1/2
1/2
9/16
9/16
5/8
5/8
3/4
3/4
7/8
7/8
1
32
32
24
32
24
20
28
18
24
16
24
14
20
13
20
12
18
11
18
10
16
9
14
8
in-lbs (Nm)
in-lbs (Nm)
in-lbs (Nm)
in-lbs (Nm)
in-lbs (Nm)
in-lbs (Nm)
in-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
ft-lbs (Nm)
20 (2.3)
24 (2.7)
35 (4.0)
40 (4.5)
50 (5.7)
95 (10.7)
95 (10.7)
17 (22.6)
20 (27.1)
30 (40.7)
35 (47.5)
50 (67.8)
55 (74.6)
75 (101.7)
85 (115.3)
105 (142.4)
115 (155.9)
150 (203.4)
160 (217.0)
170 (230.5)
175 (237.3)
302 (409.5)
300 (406.8)
466 (631.8)
-
30 (3.4)
45 (5.1)
50 (5.7)
65 (7.3)
125 (14.1)
150 (17.0)
23 (31.2)
25 (33.8)
40 (54.2)
45 (61.0)
65 (88.1)
70 (94.9)
100 (135.6)
110 (149.2)
135 (183.1)
150 (203.4)
195 (264.4)
210 (284.8)
220 (298.3)
225 (305.1)
473 (640.9)
400 (542.4)
714 (967.4)
General InformationDecal Locations1
1.3 Decal Locations
1
2
3
4
5
6
7
8
9
10
REF PART # DESCRIPTION COMMENTS QTY.
057535 Decal Kit, Toro 100 1
041206-toro Decal, Caution Symbol CE Std -Toro 2
043224-toro Decal, Equipment, Height Adj EF -Toro 5
057524-toro Decal, 100” - Toro 2
057530-toro Decal, Foot Valve Ops - Toro 1
057531-toro Decal, No Step - Toro 2
057532-toro Decal, Deck Lock - Toro 2
057533-toro Decal, Caution, Rotating Parts - Toro 1
057534-toro Decal, Caution, Hand Pinch - Toro 1
P117-toro Decal, Hands and Feet - Toro 1
063735 Decal, Lastec Logo 1
063327 Decal, 3682/96 Gearbox Fluid Not Shown 1
055430-toro Decal, Rear Tire Pressure - Toro Not Shown 2
1-4 Lastec//080216 General Information
General InformationDecal Locations 1
05753
2
0575
32
057532
057 5
32
0575
30
057
533
P11
7 -T
OR
O
057
53
2-T
OR
O
04
322
4-T
OR
O
04
3224
- TO
RO
05
752
4-T
OR
O
On
pan
fac e
057
52
4-T
OR
O
On
pan
face
041
206 -
TO
RO
05
7531
-TO
RO
041
20
6 -T
OR
O
05
7532
-TO
RO
Foo
t Pan
057
53
0
05
7534
TR1003
063
73
5
General Information Lastec//080216 1-5
General InformationBelts and Decks1
1.4 Belts and Decks
REF PART # DESCRIPTION COMMENTS QTY.
1 041630 Belt, Insta-Power 85830 2
2 059707 Drive Belt, B165 Main 1
3 061842 Deck Weldment, #5 1
4 059209 Deck Weldment, #4 1
5 059208 Deck Weldment, #3 1
6 059207 Deck Weldment, #2 1
7 061831 Deck Weldment, #1 1
1-6 Lastec//080216 General Information
General InformationBelts and Decks 1
2
1
3
4
5
6
7
1
Deck 5
Deck 4
Deck 3
Deck 2
Deck 1
TR1004
General Information Lastec//080216 1-7
General InformationRear Guard1
1.5 Rear Guard
REF PART # DESCRIPTION COMMENTS QTY.
061669 Guard Assembly, Rear Bumper 1
1 F05010-10 Nut, 3/8-16 Hex Nyloc 2
2 F05011-3 Washer, 3/8” Flat SAE 2
3 061666 Mount Plate, Rear Guard 1
4 F05007-123 Bolt, 3/8-16 x 1 1/4” Hex Head Grade 5 2
059972 Tire Assembly, 24” x 12-12 w/Toro Offset Rim 2
5 059971 Rim, 12” x 10-1/2, Offset w/ Valve Stem 1
6 059974 Tire, Toro Spec. 24” x 12-12 1
1-8 Lastec//080216 General Information
General InformationRear Guard 1
TR1001
General Information Lastec//080216 1-9
General InformationMulching Dam Kit1
1.6 Mulching Dam Kit
REF PART # DESCRIPTION COMMENTS QTY.
061880 Dam Kit, Toro Mulching 1
1 F05006-90 Bolt, 5/16-18 x 1” Carriage Grade 5 6
2 F05011-17 Washer, 5/16” SAE Flat 6
3 F05010-121 Nut, 5/16-18 Nylon Locking Jam 6
4 061879 Mulching Dam, #3 Toro 1
5 061877 Mulching Plate, #5 Deck 1
1-10 Lastec//080216 General Information
General InformationMulching Dam Kit 1
DECK 3
DECK 5
TR1002
General Information Lastec//080216 1-11
Mower//080216 2-1
2
SECTION 2 MOUNTING HARDWARE
Mounting HardwareMounting Hardware2
2.1 Mounting Hardware
Relay, 40A 12VDC Automotive
Screw, M4- .7 x 50 Socket Head
Nut, M4- .7 Prev Torq
Bolt, 5/16-18 x 1 1/2” Hex Head
Nut, 5/16-18 Nylon Lock
Bolt, #10-24 1/2” Self Tap
Wire Tie, 14” Black
Tie Wrap, 3/16” x 5 1/2” UV Black
REF PART # DESCRIPTION COMMENTS QTY.
063280 Kit, 100EZT Installation Hardware 1
1 050436 1
2 F05004-176 1
3 F05010-167 1
4 F05008-96 2
5 F05010-58 1
6 F05015-7 1
7 F05089-5 4
8 F05089-3 4
063236 Harness, 100EZT Electrical Not Shown 1
2-2 Lastec//080216 Mounting Hardware
Mounting HardwareMounting Hardware 2
TR1033
Mounting Hardware Lastec//080216 2-3
Mounting HardwareMounting Frame2
2.2 Mounting Frame
Frame Weldment, Toro 100zt Drive
Nut, 3/4-10 Nylock
Washer, 3/4” SAE Flat
Bolt, 3/4-10 x 3 1/2” Hex Head Grade 5
Sure Grip, 100zt Top Footpan
Rod Assembly, Toro Over Center Prop
Nut, 3/8-16 Half Nyloc
Spacer, 1.00” OD x .41” ID x 1/4” Nylon
Arm, Toro Prop-Rod Locking
Arm, Toro Prop-Rod Main
Bolt, 3/8-16 x 1 1/4” Carriage Grade 5
Nut, 1/4-20 Half Nylock
Strap, Two Channel Plastic
Bolt, 1/4-20 x 2 3/4” Hex Head
Fitting, 1/4-28 Straight Grease
Jack, Toro Unit Service
Nut, 1/4-20 Nylock
Grommet, Toro Jack Mount
Strap, Jack Tie Down
Washer, 1/4” SAE Flat
Bolt, 1/4-20 x 1 1/2” Hex Head Grade 5
Valve Assembly, Toro ZT Lift
Hanger Assemble, Toro Axle Support
Front Axle, Toro Frame
Footpan Assembly, Toro 100
Plate, Toro Footpan Adjust Lock
Bolt, 5/16-18 x 3/4” Hex Head
Washer, 5/16” Split Lock
Washer, 5/16” SAE Flat
REF PART # DESCRIPTION COMMENTS QTY.
059260 Frame Assembly, Toro 1
1 059243 1
2 F05010-103 6
3 F05011-62 12
4 F05009-54 6
5 062007 1
059952 1
6 F05010-124 3
7 029214 3
8 059951 1
9 059950 1
10 F05007-127 3
11 F05010-156 1
12 057333 1
13 F05005-18 1
14 P107 1
15 059936 1
16 F05010-69 1
17 059948 1
18 059946 1
19 F05011-11 2
20 F05005-124 1
21 059005 See Section 2.4 for parts 1
22 059978 See Section 2.3 for parts 1
23 059257 See Section 2.3 for parts 1
24 059940 See Section 2.5 for parts 1
25 064190 Added SN 37740710 and later 1
26 F05006-102 2
27 F05011-13 2
28 F05011-17 2
059953 Serial Number Plate, Toro Not Shown 1
F04203-2 Rivet, 1/8” x 1/4” Al AA44D Pop Not Shown 4
2-4 Lastec//080216 Mounting Hardware
Mounting HardwareMounting Frame 2
TR1014-1
Mounting Hardware Lastec//080216 2-5
Mounting HardwareFront Axle2
2.3 Front Axle
Axle Weldment, Toro 100zt
Fitting, Grease 90 Deg. 1/4-28
Orifice, 1/4-28 x .040” ID x 3/8”
Bushing, 1” ID x 1-1/4” OD x 1-1/4” Flanged
Bushing, 1 1/2” ID x 1 3/4” OD x 1 1/2” Lg Bronze
Yoke Assembly, 15” Toro Wheel
Bolt, 1/2-13 x 1” Hex Head
Washer, 1/2” Split Lock
Washer, Motor Mount
Bearing, 6206-2NSE
Yoke Weldment, 15" Toro Front Wheel
Bolt, 1/2-13 x 9 1/2” Hex Head Grade 5
Spacer, Inner Wheel Brg
Nut, 1/2-13 Nylon Hex Lock
Wheel Assembly, Toro 15” x 6-6.00 Air Filled
Wheel, 15” x 6-6.00 Air Filled
Fitting, 1/4-28 45 Deg. Grease
Bearing Race Insert, 3/4” Trb
Bearing, Tapered Roller 3/4” ID
Seal, 1 1/8” ID Trb Bearing
Spacer, Outer Wheel Bearing
Nut, 1/2-13 Half Nyloc
Spacer, 3/16 Thk Deck Height
Plate, Axle Support Hanger
Bolt, 1/2-13x1 1/2 Carriage, Zinc
Washer, 3/4 Split Lock
Bolt, 3/4-16x1 1/2 HH Gr5
REF PART # DESCRIPTION COMMENTS QTY.
059257 Front Axle, Toro Frame 1
1 059255 1
2 P123 4
3 063202 2
4 P109 2
5 018894 2
059258 2
6 F05008-50 1
7 F05011-9 1
8 018751 1
9 P11035 2
10 059224 1
11 F05008-155 1
12 063282 1
13 F05010-8 1
059259 1
14 059259-1 1
15 P294 1
16 P402 2
17 P292 2
18 P293 2
19 063281 2
059978 Hanger Assembly, Toro Axle Support 1
20 F05010-127 2
21 029109 2
22 059977 1
23 F05008-150 2
24 F05011-6 1
25 F05013-72 1
2-6 Lastec//080216 Mounting Hardware
Mounting HardwareFront Axle 2
TR1014-2
Mounting Hardware Lastec//080216 2-7
Mounting HardwareFoot Lift Valves2
2.4 Foot Lift Valve
Pedal Weldment, Toro Control Valve Foot
Nut, M8 x 1.25 Free Zinc Plate
Valve, Toro Deck Lift Bucher
Fitting, OFS x ORB 06-08 Str
Bolt, 5/16-18 x 5/8” Hex Head Grade 5
Fitting, OFS x ORB 08-08 Str
Fitting, 90 Degree OFS x ORB 04-06 Hydraulic
Washer, 5/16” Split Lock
Fitting, Branch Tee OFS 04-04-04 Hydraulic
Hose, R16-06 High Pressure Hydraulic
Bracket Wedment, Toro Valve Mounting
s
REF PART # DESCRIPTION COMMENTS QTY.
059005 Valve Assembly, 100ZT Lift 1
1 059966 Metric threads 1
2 F05010-162 Metric 1
3 064236 1
1 Replaced Toro Deck Lift Valve (059945), (3) Hex Head Bolts (F05006-80), (3) Hex Nuts (F05010-58) and (2) 90 Degree Hydraulic Fittings (059955 for pump hose & 059956 for oil cooler hose) in units with serial #39710411 and later. See bulletins PB-0297 and IS-0298 for more information on 100EZT Valve Assembly Service Kit (064233) available for units prior to serial #39710411.
1
4 064234 1
5 F05006-54 4
6 064235 1
7 059957 2
8 F05011-13 4
9 059959 2
10 059965 1
11 064182 2
059969059968
059967
059965Hose suppliedby Toro
To Pump To Oil Cooler
TR1039
2-8 Lastec//080216 Mounting Hardware
Mounting HardwareFoot Lift Valves 2
PUMPHOSE
TORO SUPPLIED
BY
CYLINDER RETRACT
OIL COOLER
CYLINDER EXTEND
TR1014-4
Mounting Hardware Lastec//080216 2-9
Mounting HardwareFootpan Assembly2
2.5 Footpan Assembly
Handle Assembly, 421D Deck Lift
Handle, Foam .625 x 6 x 3/16 Wall
Handle, Outrigger Jack
Bolt, 1/4-20 x 1/2” Hex Head
Bracket, Deck Bar Holder
Grommet, 11/16 x 1 x 1 5/16 Rubber
Sure Grip, Seat Pan Right Side
Clip, Handle Deck
Weldment, Toro Footpan
Nut, 1/4-20 Half Nylon Lock
Screw, 10-24 x 1/2” SBHC
Foot, Rubber
Nut, #10-24 Keps
Lock, Toro Footpan
Bolt, 3/8-16 x 4 1/2” Hex Head 316 SS
Nut, 3/8-16 Hex Half Nylon Lock 316 SS
REF PART # DESCRIPTION COMMENTS QTY.
059940 Footpan Assembly, Toro 100 1
041685 1
1 048644 1
2 S04827 1
3 F05005-15 4
4 041193 1
5 015460 1
6 063356 3
7 041192 1
8 059925 1
9 F05010-156 4
10 F05004-35 2
11 P06104 2
12 F05010-14 2
13 059941 1
14 F05007-244 2
15 F05010-234 2
2-10 Lastec//080216 Mounting Hardware
Mounting HardwareFootpan Assembly 2
TR1014-3
Mounting Hardware Lastec//080216 2-11
Mower//080216 3-1
3
SECTION 3 DRIVE SYSTEM
Drive SystemGearbox Tensioner3
3.1 Gearbox Tensioner
Boss, Idler Pulley Standoff
Ring, 62mm IR Din #472 Retaining
Bearing, Spindle Top 6305 RS
Pulley, 5” OD Idler, Flat
REF PART # DESCRIPTION COMMENTS QTY.
059703 1
1 Redesigned to improve belt performance on units with serial #40880911 and later. Tensioner Service Kit (067311) is available for units prior to serial #40880911.
Tensioner Assembly, Main Drive 1
1 F05010-127 Nut, 1/2-13 Half Nyloc 1
2 F05011-2 Washer, 1/2 SAE Flat 3
3 059299 Spring, Counter Balance 1
4 F05010-35 Nut, 1/2-13 Hex 1
5 F05011-9 Washer, 1/2 Split Lock 1
6 F05008-116 Bolt, 1/2-13 x 2” Full Thread Grade 5 1
7 F05010-8 Nut, 1/2-13 Nyl Hex Lock 1
8 059702 Tensioner Weldment, Main 1
045295 Pulley Assembly, 5” OD Idler, Flat 1
9 045297 1
10 F04254-12 Metric 2
11 P103 1
12 045296 1
13 F05008-74 Bolt, 1/2-13 x 2 1/2” Hex Head Grade 5 1
14 P294 Fitting, 1/4-28 45 Deg Grease 1
15 029842 Bushing, 3/4” ID x 1” OD x 1” Oil 2
16 067092 Keeper, Main Drive Tensioner 1
17 F81033-6 Nut, 10mm x 1.25 Nylon 2
18 046465 Dampener, Hand Control 1
19 F05010-192 Nut, M10-1.25 Free Zinc Plate 1
20 F05010-124 Nut, 3/8-16 Half Nyloc 2
21 067098 Plate, Idler Dampener Clamp 1
22 067099 Plate Weldment, Idler Dapmener Clamp 1
23 F05007-201 Bolt, 3/8-16 x 2-1/4” Hex Head Grade 5 2
3-2 Lastec//080216 Drive System
Drive SystemGearbox Tensioner 3
TR1005
Drive System Lastec//080216 3-3
Drive SystemGearbox Assembly3
3.2 Gearbox Assembly
REF PART # DESCRIPTION COMMENTS QTY.
1 F05007-87 Bolt, 3/8-16 x 1” Hex Head Grade 5 6
2 F05011-4 Washer, 3/8” Split Lock 6
3 059294 Gearbox, Toro (Comer Industries) Holds 12 oz. SAE EP90 (80W-90)
1
4 059295 Sheave, B Section, 6 1/2” OD Steel 1
5 059721 Bushing, 7/8” Bore Taper (w/ Set Screws) Torque to 96-120 in-lbs. 1
6 P04101-1 Key, #606 Woodruff 1
3-4 Lastec//080216 Drive System
Drive SystemGearbox Assembly 3
TR1018-2
Drive System Lastec//080216 3-5
Mower//080216 4-1
4
SECTION 4 MOWER DECKS
Mower DecksDeck 1 Hardware4
4.1 Deck 1 Hardware
Deflector Plate, #5 Deck Grass
Bolt, 3/8-16x1 Carriage
Nut, 3/8-16 Flanged Hex Nylock
Bolt, 5/16-18 x 3/4” Hex Head Grade 5
Washer, 5/16” Split Lock
Clamp Plate, #1 Deck Trap Door
Door, #1 Deck Trap
REF PART # DESCRIPTION COMMENTS QTY.
1 067043 1
1 Replaced 043217 1-1/4” Hole Plug Cover. Deck cover was redesigned to accept 1-3/8” hole plug cover (7/11).
Cover, 1 3/8”” Hole Plug 1
2 F05010-121 Nut, 5/16-18 Nylon Locking Jam 3
3 046293 Washer, Throttle Friction 2
4 061836 Cover, #1 Deck 1
5 F81033-6 Nut, 10mm x 1.25 Nylon Metric 1
6 046465 Dampener, Hand Control 1
7 F05010-192 Nut, M10-1.25 Free Zinc Plate Metric 1
8 F81003-25 Bolt, M10-1.25x30mm HHFT 8.8 Metric 1
9 F05010-10 Nut, 3/8-16 Hex Nylock 1
10 F05008-74 Bolt, 1/2-13 x 2 1/2” Hex Head Grade 5 2
11 F05009-20 Bolt, 5/8-11 x 2 1/2” Hex Head Grade 5 2
12 F05010-185 Nut, 5/8-11 FlexLoc 2
13 F05010-8 Nut, 1/2-13 Nyl Hex Lock 2
059082 Deflector Assembly, Grass 1
14 059081 1
15 F05007-165 2
16 F05010-222 2
059126 2
2 059126 replaced 064555 including (4) F05006-102 5/16-18 x 3/4” Hex Head Bolt, (4) F05011-3 3/8” Flat Washer, 064557 #1 Deck Trap Door Clamp Plate and 064556 #1 Deck Trap Door (Serial #49311013 and later). Previously, 064555 replaced 059126 #1 Deck Trap Door Assembly (9/11).
Door Assembly, #1 Deck Trap 1
17 F05006-102 4
18 F05011-3 4
19 059125 1
20 059096 1
21 041630 Belt, Insta-Power 85830 1
4-2 Lastec//080216 Mower Decks
Mower DecksDeck 1 Hardware 4
TR1036D
Mower Decks Lastec//080216 4-3
Mower DecksDouble Pulley Spindle, Decks 1, 5 (Serial #46331112 and later)4
4.2 Double Pulley Spindle, Decks 1, 5 (Serial #46331112 and later)
Fitting, 1/4-28 Straight Grease
Bolt, Spindle Single Pulley
Washer, 1/2” Plain Belleville
Key, 1/4” Square x 1 1/2” Long
Sheave, Double - Mower Deck
Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5
Spindle Assembly, ZT Cast
Nut, 3/8-16 Flanged Hex Nyloc
Blade, 21” x 2 1/2” x 1/4” High Lift
Blade, 21” Low-Lift
Blade, 21” Gator Mulching
Blade, 21” x 2 1/2” x 1/8” Low-Lift Ultra
Stiffener Weldment, Blade E-Series
Washer, 5/8 Split Lock
Bolt, 5/8-18 x 1 3/4” Hex Head Grade 5
Channel, Blade Stiffener
REF PART # DESCRIPTION COMMENTS QTY.
072624 Spindle Assembly, EZT 21" D6.3-6.3 Non-saleable item. Parts must be purchased separately.
1
1 P107 1
2 045677 Maximum Torque: 57 ft-lbs 1
3 F05011-97 1
4 028080 1
5 067688 1
6 F05007-78 4
7 067696 See Section 4.3 for parts 1
8 F05010-222 4
9 P128 1
P246 Optional 1
P322 Optional 1
063265 Optional 1
10 064198 1
11 F05011-27 Remove to install Anti-Scalp Blade Disc
1
12 F05009-95 Torque Value: 75 ft-lbs 1
13 028254 1
4-4 Lastec//080216 Mower Decks
Mower DecksDouble Pulley Spindle, Decks 1, 5 (Serial #46331112 and later) 4
100_205
Mower Decks Lastec//080216 4-5
Mower DecksSpindle Housing, Decks 1, 2, 4 and 5 (Serial #46331112 and later)4
4.3 Spindle Housing, Decks 1, 2, 4 and 5 (Serial #46331112 and later)
Bearing, 6206-2NSE
O-Ring, 2 1/2” ID x 2 3/4” OD
Spacer, Bearing Housing
Spindle Housing, ZT- Common Core
Spacer, Spindle Bearing Housing
Washer, 1.50” x 1.185” x 16Ga
Washer, 2.435” x 1.185” x 11Ga
Shaft, Blade Spindle ZT Cast
Concerning Nachi Sealed Bearings:
One of the most common misconceptions that cause a high number of bearing failures is that a bearing needs to be completely packed full. Many people have been taught; the more grease, the better. We have even heard of cases where people do not feel bearing manufacturers use enough grease in sealed and shielded ball bearings, so they remove one seal or shield and pack the bearing with more grease. These misconceptions are completely false. Over lubri-cating the bearings forces the motor to work harder.
Nachi standard grease fill for sealed and shielded ball bearings is 20% to 30% full
Too much grease can cause excess friction, thereby overheating the bearing and causing remature failure.
Only a small of grease is required to lubricate a bearing in motion.
When a bearing is in motion, most of the grease is pushed to the side (channeling) leaving a thin film of oil between the raceways and rolling elements.
When using open bearings, pack the bearing as follows:
REF PART # DESCRIPTION (Indicates Non-Saleable Items) COMMENTS QTY.
067696 Spindle Assembly, Center w/Stiffener Non-saleable item. Parts must be purchased separately.
1
1 P11035 3
2 P105 4
3 072511 1
4 067999 1
5 067686 1
6 034947 1
7 034948 1
8 067687 1
4-6 Lastec//080216 Mower Decks
Mower DecksSpindle Housing, Decks 1, 2, 4 and 5 (Serial #46331112 and later) 4
100_188
Mower Decks Lastec//080216 4-7
Mower DecksSpindle Assembly, Deck 1 & 5 (Prior to Serial #46331112)4
4.4 Spindle Assembly, Deck 1 & 5 (Prior to Serial #46331112)
Fitting, 1/4-28 Straight Grease
Bolt, Spindle Pulley
Washer, 1/2” Plain Belleville
Key, 1/4” x 2 1/2”
Sheave, Double - 2561 Mower
Washer, 1/4” x 1.47” x 1.01”
Bolt, 3/8-16 x 1 1/2” Carriage Grade 5
Plate, Deck Reinforcing
Spindle Assembly, Center w/Stiffener
Nut, 3/8-16 Hex Nyloc
Blade, 21” x 2 1/2” x 1/4” High Lift
Blade, 21” Low-Lift
Blade, 21” Gator Mulching
Blade, 21” x 2 1/2” x 1/8” Low-Lift Ultra
Stiffener Weldment, Blade E-Series
Channel, Blade Stiffener
Washer, 5/8” Split Lock
Bolt, 5/8-18 x 1 3/4” Hex Head Grade 5
Blade Disc, Anti-Scalp
REF PART # DESCRIPTION COMMENTS QTY.
063278 Spindle Assembly, Double Sheave Low w/Anti Non-saleable item. Parts must be purchased separately.
1
1 P107 1
1 P107 replaced P04107 3/16” x 3/16” Straight Grease Fitting to improve durability (Serial #41071011 and later).
1
2 045677 Maximum Torque: 57 ft-lbs 1
3 F05011-97 1
4 027053 1
5 040049 1
6 046273 1
7 F05007-85 4
8 044862 2
9 043246 See Section 4.5 for parts 1
10 F05010-10 4
11 P128 1
P246 Optional 1
P322 Optional 1
063265 Optional 1
12 064198 1
13 028254 1
14 F05011-27 1
15 F05009-95 Torque Value: 75 ft-lbs 1
16 048898 Optional 1
4-8 Lastec//080216 Mower Decks
Mower DecksSpindle Assembly, Deck 1 & 5 (Prior to Serial #46331112) 4
TR1008B
Mower Decks Lastec//080216 4-9
Mower DecksSpindle Housing(Prior to Serial #46331112)4
4.5 Spindle Housing(Prior to Serial #46331112)
Bolt, 5/16-18 x 5” Hex Head Grade 5
Bolt, 5/16-18 x 1 1/4” Hex Head Full Thread Gr5
Washer, 5/16” Split Lock
Plate, Deck Reinforcing
Seal, 2561 Spindle
Collar, Spindle Top
O-Ring, Spindle
Bearing, 6206-2NSE
Housing, Spindle
Pin, 1/8” x 1/2” Roll
Nut, 5/16-18 Nylon Lock Hex
Spacer, Spindle Bearing
O-Ring, 2 7/16" ID x 3/16" Diameter
Washer, 1.50” x 1.185” x 16Ga
Washer, 2.435” x 1.185” x 11Ga
Shaft, Center Blade Spindle
Instruction Sheet, 1-12 Spindle
Concerning Nachi Sealed Bearings:
One of the most common misconceptions that cause a high number of bearing failures is that a bearing needs to be completely packed full. Many people have been taught; the more grease, the better. We have even heard of cases where people do not feel bearing manufacturers use enough grease in sealed and shielded ball bearings, so they remove one seal or shield and pack the bearing with more grease. These misconceptions are completely false. Over lubri-cating the bearings forces the motor to work harder.
Nachi standard grease fill for sealed and shielded ball bearings is 20% to 30% full
Too much grease can cause excess friction, thereby overheating the bearing and causing remature failure.
Only a small of grease is required to lubricate a bearing in motion.
When a bearing is in motion, most of the grease is pushed to the side (channeling) leaving a thin film of oil between the raceways and rolling elements.
When using open bearings, pack the bearing as follows:
REF PART # DESCRIPTION (Indicates Non-Saleable Items) COMMENTS QTY.
043246 Spindle Assembly, Center w/Stiffener Non-saleable item. Parts must be purchased separately.
1
1 F05006-140 Added after serial # 33351208 3
2 F05006-93 3 deleted after serial # 33341208
3
3 F05011-13 3 deleted after serial # 33341208
3
4 034921 1
5 034969 1
6 034951 1
7 062999 Added after serial # 34990809 1
8 P11035 3
9 034945 1
10 F05012-64 1
11 F05010-58 Added after serial # 33351208 3
12 034950 1
13 F04254-45 2
14 034947 1
15 034948 1
16 043245 1
17 IS-0387 1
4-10 Lastec//080216 Mower Decks
Mower DecksSpindle Housing(Prior to Serial #46331112) 4
LT0024B
Mower Decks Lastec//080216 4-11
Mower DecksDecks 1 and 5 Rocker Assembly4
4.6 Decks 1 and 5 Rocker Assembly
Nut, 3/4-10 Flexloc
Spacer, 1.13” OD x .75” ID x .5”
Wheel Assembly, 9” x 3.5” Solid DM
Spacer, Dual Wheel Outer Bearing
Rocker, Weldment #1 Trim Deck
Rocker Weldment, Right
Bolt, 5/8-11 x 2 1/2” Grade 5 Carriage
Sleeve, .875” x 1.14” Long Bushing
Bushing, .875” Bearing
Plate, 521 Rocker Tube Limit
Nut, 5/8-11 FlexLoc
Sleeve, 7/8” OD x 4.87” Long Bushing
Nut, 1/2-13 Nyl Hex Lock
Bolt, 5/8-11 x 6 1/2” Hex Head Grade 5
Washer, 5/8” SAE Flat
H Block Weldment, Left Rocker
H-Block Weldment, Right Rocker
Spacer, .53” ID x 1 1/4” OD x 1 1/4” Long
Bolt, 1/2-13 x 3” Hex Head Grade 5
Rod Assembly, 521 ZT Rocker Spacer
Wheel Yoke Assembly, 9” Foam Filled
Fitting, 1/4-28 Straight Grease
NOTE: Deck 1 and Deck 5 Rocker assemblies are mirror images of each other. Be sure to order the correct weldments for each deck.
CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.
REF PART # DESCRIPTION COMMENTS QTY.
061828 Rocker Assembly, Left Side Deck 1 1
061843 Rocker Assembly, Right Deck 5 1
1 F05010-178 1
2 P296 1
3 061826 See Section 4.8 for parts 1
4 T125 1
5 061621 Deck 1 1
059717 Deck 5 1
6 F05009-123 3
7 062149 1
1 Replaced (049276) Bushing, Urethane Bearing Inner and (049277) Bearing Half, Urethane Bushed and (058353) Sleeve, Urethane Bushing 4.75” in models with serial # 34990809 and later. See Product Bulletin PB-0262 for more information.
3
8 0621151 5
9 058341 1
10 F05010-185 5
11 0621571 1
12 F05010-8 1
13 F05009-39 1
14 F05011-5 2
15 059719 Deck 1 1
059725 Deck 5 1
16 049868 1
17 F05008-23 1
18 058336 See Section 4.9 for parts 1
19 061827 See Section 4.7 for parts 1
20 P107 1
4-12 Lastec//080216 Mower Decks
Mower DecksDecks 1 and 5 Rocker Assembly 4
TR1009B
Deck 1 Rocker
Deck 5 Rocker
Mower Decks Lastec//080216 4-13
Mower Decks9” Wheel Yoke Assembly4
4.7 9” Wheel Yoke Assembly
REF PART # DESCRIPTION COMMENTS QTY.
061827 1
1 (1) 063216 replaced (1) T104 1” ID x 1-3/4” OD x 1/4” Spacer and added (1) F05011-115 and (1) F05011-116 to improve durability (Serial #38861210 and later).
Wheel Yoke Assembly, 9” Foam Filled 1
1 F05007-118 Bolt, 3/8-16 x 3/4” Hex Head Grade 5 1
2 F05011-4 Washer, 3/8” Split Lock 1
3 F05011-104 Washer, 3/8 x 1 1/2” x 1/8” 1
4 F05011-116 Washer, 1” ID .06 SS Shim 1
5 F05011-115 Washer, 1” ID .03 SS Shim 1
6 063216 Spring, Wheel Yoke 1-0 Urethane 1
7 T104 Spacer, 1 3/4” OD x 1 1/64” ID x 1/4” 1
8 P109 Bushing, 1” ID x 1 1/4” OD x 1 1/4” Flanged 2
9 059105 Yoke Weldment, 9” w/6” Shaft 1
10 F05009-104 Bolt, 3/4” ID x 6” Carriage Grade 5 1
11 F05011-62 Washer, 3/4” SAE Flat 1
12 F05010-177 Nut, 3/4-10 Stover Lock 1
13 042898 Spacer, 3/4” Axle Bolt 2
14 061826 Wheel Assembly, 9” x 3.5” Solid DM See Section 4.8 for parts 1
4-14 Lastec//080216 Mower Decks
Mower Decks9” Wheel Yoke Assembly 4
TR1021
Mower Decks Lastec//080216 4-15
Mower Decks9” x 3.5” Wheel Assembly, Solid4
4.8 9” x 3.5” Wheel Assembly, Solid
NOTE: Wheels are shipped unlubricated from the factory. Insure proper lubrication, bear-ing preloading, and torque specifications are met. Use Loctite on all bolts. Tighten hub nuts to 145-170 in-lbs.
NOTE: All wheels should be lubricated, insuring grease passes through the seals, after every 8 hours of operation. (See Section 5 of the Owner’s Manual).
NOTE: When checking bearing preload, wheels should be placed on the spindles loose enough to spin freely only one complete revolution when spun by hand. Insure spacers are properly installed.
REF PART # DESCRIPTION COMMENTS QTY.
061826 Wheel Assembly, 9” x 3.5” Reliance DM 1
1 F05010-17 Nut, 5/16-18 Hex Torque to 145-170 in-lbs 4
2 F05011-13 Washer, 5/16” Split Lock 4
3 061826-1 Tire, Carlisle Reliance No-Flat Smooth Not Sold Separately 1
4 P293 Seal, 1 1/8” ID Trb Bearing 2
5 P292 Bearing, Tapered Roller 3/4” ID 2
6 048455 Spacer, 3/4” Wheel Bearing 1
061826-2 Hub Assembly, 9/11” Demountable 1
7 061826-3 Hub, 9/11” Demountable 1
8 P402 Bearing Race Insert, 3/4” TRB 2
9 P294 Fitting, 1/4-28 45 Deg. Grease 1
4-16 Lastec//080216 Mower Decks
Mower Decks9” x 3.5” Wheel Assembly, Solid 4
TR1017
Mower Decks Lastec//080216 4-17
Mower DecksRocker Rod Assembly4
4.9 Rocker Rod Assembly
Rod End, 1/2-20 Female
Nut, 1/2-20 Hex Jam
Nut, 1/2-20 Jam Nyl Lock
Spacer, 3/16” Thk Knurled
Spacer, 3/16” Thk Deck Height
Spring, .72” x 1.5” x .063” Compression
Washer, 1/2” SAE Flat
Bolt, 1/2-20 x 6 1/2” Hex Head Grade 8
REF PART # DESCRIPTION COMMENTS QTY.
058336 Rod Assembly, 521ZT Rocker Spacer 1
1 019348 1
2 F05010-16 1
3 F05010-79 1
4 029109-1 5
5 029109 12
6 041631 1
7 F05011-2 1
8 F05008-171 1
4-18 Lastec//080216 Mower Decks
Mower DecksRocker Rod Assembly 4
100_021
Mower Decks Lastec//080216 4-19
Mower DecksDeck 1 Idler Assembly4
4.10 Deck 1 Idler Assembly
Ring, 62mm IR Din #472 Retaining
Bearing, Spindle Top 6305 RS
Pulley, 5” OD Idler, Flat
Boss, Idler Pulley Standoff
Ring, 62mm IR Din #472 Retaining
Bearing, Spindle Top 6305 RS
Pulley, 5” OD Idler, V Groove
Boss, Idler Pulley Standoff
REF PART # DESCRIPTION COMMENTS QTY.
056565 Idler Assembly, 521 1
1 F05008-10 Bolt, 1/2-13 x 2 1/4” Hex Head Grade 5 2
2 062051 Washer, Water Shed Pulley 2
045295 Pulley Assembly, 5” OD Idler, Flat 1
3 F04254-12 2
4 P103 1
5 045296 1
6 045297 1
7 056566 Weldment, 521E Idler Plate 1
8 P123 Fitting, Grease 90 Deg. 1/4-28 1
9 F05010-127 Nut, 1/2-13 Half Nylon Lock 2
10 029842 Bushing, 3/4” ID x 1” OD x 1” Oil 2
11 F05010-225 Nut, 3/4-10 Flanged Hex Nylock 1
12 F05011-77 Washer, 3/4” AN Yel/Cad 1
105249 Pulley Assembly, 5In OD Idler, V Groove Tall 1
13 F04254-12 2
14 P103 1
15 045270 1
16 045297 1
17 F05006-76 Bolt, 5/16-18 x 1 1/2” Hex Head Full Thread Grade 5 1
18 F05010-17 Nut, 5/16-18 Hex 1
19 F05010-221 Nut, 5/16-18 Flanged Hex Nylock 1
20 P410 Spring, 1” x 7” Extension 1
21 F05011-68 Washer, 1/2” Standard Flat 2
4-20 Lastec//080216 Mower Decks
Mower DecksDeck 1 Idler Assembly 4
100_009D
Mower Decks Lastec//080216 4-21
Mower DecksAnti-Scalp Roller Assembly (Optional)4
4.11 Anti-Scalp Roller Assembly (Optional)
REF PART # DESCRIPTION COMMENTS QTY.
067135 Anti-Scalp Roller Assembly, 3300 Optional 1
1 067142 Axle Rod, 3300 Anti-Scalp Roller 1
2 067136 Bracket Weldment, 3300 Anti-Scalp 1
3 P438 Wheel, Anti-Scalp 6” x 3.25” x 3/4” ID 1
4 F05011-9 Washer, 1/2” Split Lock 2
5 F05008-71 Bolt, 1/2-13 x 1” Hex Head Full Thread 2
6 F05007-165 Bolt, 3/8-16 x 1” Carriage Grade 5 3
7 F05010-10 Nut, 3/8-16 Hex Nyloc 3
8 F05011-3 Washer, 3/8” Flat SAE 3
4-22 Lastec//080216 Mower Decks
Mower DecksAnti-Scalp Roller Assembly (Optional) 4
100_176C
Mower Decks Lastec//080216 4-23
Mower DecksDeck 2 Hardware4
4.12 Deck 2 Hardware
Baffle Weldment, #2 Blowout
Nut, 5/16-18 Nylon Locking Jam
Bolt, 5/16-18 x 3/4” Carriage
CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.
REF PART # DESCRIPTION COMMENTS QTY.
1 F81033-6 Nut, 10mm x 1.25 Nylon Metric 1
2 F05010-192 Nut, M10-1.25 Free Zinc Plate Metric 1
3 F05004-277 Bolt, M10-1.25 x 40mm Hex Head Grade 8.8 Metric 1
4 F05009-35 Bolt, 5/8-11 x 2 3/4” Hex Head Grade 5 3
5 049870 Bushing, Urethane Pivot 4
6 F05011-40 Washer, 5/8” Standard Flat 2
7 F05010-185 Nut, 5/8-11 FlexLoc 4
8 059168 Hinge Weldment, #2 Deck 1
9 F05008-74 Bolt, 1/2-13 x 2 1/2” Hex Head Grade 5 2
10 F05011-9 Washer, 1/2” Split Lock 1
11 059078 Tube, Belt Keeper 1
12 F05009-41 Bolt, 5/8-11 x 1 1/2” Hex Head Full Thread Grade 5 1
13 061855 Spacer, Bearing 1
14 061856 Bearing, 1.25” x 2.25” x .50” 1
15 F05011-5 Washer, 5/8” SAE Flat 1
16 F05010-96 Nut, 5/8-11 Jam Nyl Lock 1
17 F05008-33 Bolt, 1/2-13 x 1 1/2” Hex Head Grade 5 1
18 018751 Washer, Motor Mount 1
19 F05010-127 Nut, 1/2-13 Half Nyloc 2
20 F05009-20 Bolt, 5/8-11 x 2 1/2” Hex Head Grade 5 1
21 F05010-8 Nut, 1/2-13 Nyl Hex Lock 2
22 F05008-134 Bolt, 1/2-13 x 3 1/4” Hex Head Grade 5 1
23 062149 Sleeve, .875” x 1.14” Lg Bushing 2
24 062115 Bushing, .875” Bearing 2
25 057505 Bolt, 5/16-18 x 2” Elevator 1
26 F05011-13 Washer, 5/16” Split Lock 1
27 F05010-17 Nut, 5/16-18 Hex 1
064564 Baffle Assembly, #2 Blowout Added (9/11) 1
28 064565 1
29 F05010-121 2
30 F05006-86 2
4-24 Lastec//080216 Mower Decks
Mower DecksDeck 2 Hardware 4
TR1016-1D
Mower Decks Lastec//080216 4-25
Mower DecksDeck 2 Covers4
4.13 Deck 2 Covers
Cover,#1 Deck Sliding
Bumper, Rubber Button
Cover, #2 Deck Sliding
Nut, 5/16-18 Nylon Locking Jam
Washer, 5/16” SAE Flat
Screw, #10 x 1/2 Long AB Thrd Slot Hex Head
Hinge, 521E Sliding Cover
Pivot Bearing, Cover
Bolt, 5/16-18 x 1/2” Hex Head Grade 5
Cover Plate, Left
Bolt, 5/16-18 x 3/4” Hex Head Grade 5
Washer, 5/16” Split Lock
Washer, 5/16” SAE Flat
Cover, 1 3/8”” Hole Plug
Guard Weldment, #2 Front
Guard Weldment, #2 rear
Clamp, 1/4" Wire 13/32 Mtg Hole
Deflector Plate, #5 Deck Grass
Bolt, 3/8-16x1 Carriage
Nut, 3/8-16 Flanged Hex Nylock
Bolt, 5/16-18 x 3/4” Hex Head Grade 5
Washer, 5/16” Split Lock
Clamp Plate, #2 Deck Trap Door
Door, #2 Deck Trap
Washer, 5/16” x 1 1/4” Fender
Door, #2/4 Deck Trap
Bolt, 5/16-18 x 3/4” Hex Head Grade 5
Washer, 5/16” Split Lock
Clamp Plate, #2 Deck Trap Door
Door, #2 Deck Trap
REF PART # DESCRIPTION COMMENTS QTY.
059708 Cover Assembly, Left Transition 1
1 059709 1
2 059083 4
3 059710 1
4 F05010-121 4
5 F05011-17 4
6 F05015-36 8
7 058597 1
8 058844 2
9 F05006-15 4
059289 Cover Assembly, #2 Deck 1
10 059133 1
11 F05006-102 6
12 F05011-13 6
13 F05011-17 6
14 067043 1
1 Replaced 043217 1-1/4” Hole Plug Cover. Deck cover was redesigned to accept 1-3/8” hole plug cover (7/11).
1
15 061838 1
16 061837 1
17 024155 1
059082 Deflector Assembly, Grass 1
18 059081 1
19 F05007-165 2
20 F05010-222 2
064558 2
2 064558 modified to improve fit (2/12). 064558 replaced 061603 #2 Trap Door Assembly including (3) F05006-27 5/16-18 x 1” Hex Head Bolt, (3) F05011-13 5/16” Split Lock Washer, 058841 #2 Deck Trap Door Clamp Plate and 059797 #2 Deck Trap Door (9/11).
Door Assembly, #2 Trap 1
21 F05006-102 4
22 F05011-13 4
23 064560 1
24 059797 1
25 F05011-50 2
26 067376 1
064661 Door Assembly, #2 Trap Added (9/11) 1
27 F05006-102 2
28 F05011-13 2
29 064663 1
30 064662 1
4-26 Lastec//080216 Mower Decks
Mower DecksDeck 2 Covers 4
TR1016-2C
Mower Decks Lastec//080216 4-27
Mower DecksDouble Pulley Spindle, Decks 2, 4 (Serial #46331112 and later)4
4.14 Double Pulley Spindle, Decks 2, 4 (Serial #46331112 and later)
Fitting, 1/4-28 Straight Grease
Bolt, Spindle Pulley 1/2-13 x 1-3/4
Washer, 1/2” Plain Belleville
Key, 1/4” Square x 1 1/2” Long
Sheave, Double - Mower Deck
Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5
Spindle Assembly, ZT Cast
Nut, 3/8-16 Flanged Hex Nyloc
Blade, 21” x 2 1/2” x 1/4” High Lift
Blade, 21” Low-Lift
Blade, 21” Gator Mulching
Blade, 21” x 2 1/2” x 1/8” Low-Lift Ultra
Stiffener Weldment, Blade E-Series
Washer, 5/8 Split Lock
Bolt, 5/8-18 x 1 3/4” Hex Head Grade 5
Channel, Blade Stiffener
REF PART # DESCRIPTION COMMENTS QTY.
072623 Spindle Assembly, EZT 21" D6.3-6.3 Spacer Non-saleable item. Parts must be purchased separately.
1
1 P107 1
2 059142 Maximum Torque: 57 ft-lbs 1
3 F05011-97 1
4 028080 1
5 067688 1
6 F05007-78 4
7 067696 See Section 4.3 for parts 1
8 F05010-222 4
9 P128 1
P246 Optional 1
P322 Optional 1
063265 Optional 1
10 064198 1
11 F05011-27 Remove to install Anti-Scalp Blade Disc
1
12 F05009-95 Torque Value: 75 ft-lbs 1
13 028254 1
4-28 Lastec//080216 Mower Decks
Mower DecksDouble Pulley Spindle, Decks 2, 4 (Serial #46331112 and later) 4
100_204
Mower Decks Lastec//080216 4-29
Mower DecksSpindle Assembly, Deck 2 & 4 (Prior to Serial #46331112)4
4.15 Spindle Assembly, Deck 2 & 4 (Prior to Serial #46331112)
Fitting, 1/4-28 Straight Grease
Bolt, Spindle Pulley 1/2-13 x 1 3/4”
Washer, 1/2” Plain Belleville
Key, 1/4” x 2 1/2”
Sheave, Double - 2561 Mower
Washer, 3/8” x 1.5” x 1.01”
Washer, 1/4” x 1.47” x 1.01”
Bolt, 3/8-16 x 1 1/2” Carriage Grade 5
Plate, Deck Reinforcing
Spindle Assembly, Center w/Stiffener
Nut, 3/8-16 Hex Nyloc
Blade, 21” x 2 1/2” x 1/4” High Lift
Blade, 21” Low-Lift
Blade, 21” Gator Mulching
Blade, 21” x 2 1/2” x 1/8” Low-Lift Ultra
Stiffener Weldment, Blade E-Series
Channel, Blade Stiffener
Washer, 5/8” Split Lock
Bolt, 5/8-18 x 1 3/4” Hex Head Grade 5
Blade Disc, Anti-Scalp
REF PART # DESCRIPTION COMMENTS QTY.
063277 Spindle Assembly, Double Sheave w/Anti Non-saleable item. Parts must be purchased separately.
1
1 P107 1
1 P107 replaced P04107 3/16” x 3/16” Straight Grease Fitting to improve durability (Serial #41071011 and later).
1
2 059142 Maximum Torque: 57 ft-lbs 1
3 F05011-97 1
4 027053 1
5 040049 1
6 043249 1
7 046273 1
8 F05007-85 4
9 044862 2
10 043246 See Section 4.5 for parts 1
11 F05010-10 4
12 P128 1
P246 Optional 1
P322 Optional 1
063265 Optional 1
13 064198 1
14 028254 1
15 F05011-27 1
16 F05009-95 Torque Value: 75 ft-lbs 1
17 048898 Optional 1
4-30 Lastec//080216 Mower Decks
Mower DecksSpindle Assembly, Deck 2 & 4 (Prior to Serial #46331112) 4
TR1007B
Mower Decks Lastec//080216 4-31
Mower DecksDeck 3 Hardware4
4.16 Deck 3 Hardware
REF PART # DESCRIPTION COMMENTS QTY.
1 F05008-74 Bolt, 1/2-13 x 2 1/2” Hex Head Grade 5 1
2 F05011-9 Washer, 1/2” Split Lock 1
3 062051 Washer, Water Shed Pulley 1
045295 Pulley Assembly, 5” OD Idler, Flat 1
4 F04254-12 Ring, 62mm IR Din #472 Retaining 2
5 P103 Bearing, Spindle Top 6305 RS 1
6 045296 Pulley, 5” OD Idler, Flat 1
7 045297 Boss, Idler Pulley Standoff 1
8 019535 Spacer, 3/8” Deck Lift 425 Yzc 1
9 F05010-10 Nut, 3/8-16 Hex Nyloc 1
10 F05007-78 Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5 1
11 F05010-127 Nut, 1/2-13 Half Nyloc 4
12 018751 Washer, Motor Mount 2
13 059299 Spring, Counter Balance 2
14 F05008-33 Bolt, 1/2-13 x 1 1/2” Hex Head Grade 5 2
15 062149 1 Sleeve, .875” x 1.14” Long Bushing 2
16 0621151 Bushing, .875” Bearing 2
064568 2 Door Assembly #3 Deck Trap 1
17 F05006-102 Bolt, 5/16-18 x 3/4” Hex Head Grade 5 3
18 F05011-13 Washer, 5/16” Split Lock 3
19 064570 Clamp Plate, #3 Deck Trap Door 1
20 064569 Door, 521E/Z #3 Deck Trap 1
059706 Pulley Assembly, 7” OD Idler 1
21 F05010-127 Nut, 1/2-13 Half Nyloc 1
22 F05011-2 Washer, 1/2” SAE Flat 3
062143 3 Keeper Assembly, Drive Belt 1
23 067093 Keeper Weldment, Drive Belt (Bottom) 1
24 067095 Keeper Weldment, Drive Belt (Top) 1
25 F05005-137 Bolt, 1/4-20 x 5/8” Hex Head Grade 5 2
26 F05011-14 Washer, 1/4” Split Lock 2
27 059705 Sheave, 7" OD "B" Section Idler 1
28 F05008-134 Bolt, 1/2-13 x 3” Hex Head Grade 5 1
29 F04254-46 Ring, 3/4” External - External 1
30 049870 Bushing, Urethane Pivot 4
064571 Door Assembly, #3 Deck Trap Added (9/11) 1
31 F05006-102 Bolt, 5/16-18 x 3/4” Hex Head Grade 5 2
32 F05011-13 Washer, 5/16” Split Lock 2
33 064573 Clamp Plate, #3 Deck Trap Door 2
34 064572 Door, 521E/Z #3 Deck Trap 1
4-32 Lastec//080216 Mower Decks
Mower DecksDeck 3 Hardware 4
CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.
35 072490 Plate Weldment, Toro Belt Guard 1
1 Replaced (049276) Bushing, Urethane Bearing Inner and (049277) Bearing Half, Urethane Bushed in models with serial # 34990809 and later. See Product Bulletin PB-0262 for more information.
2 Replaced 058848 #3 Trap Door Assembly including (2) F05006-27 5/16-18 x 1” Hex Head Bolt, (2) F05011-13 5/16” Split Lock Wash-er, 058839 #3 Deck Trap Door Clamp Plate and 058812 521E/Z #3 Deck Trap Door (9/11).
3 Modified to improve belt performance (Serial #40880911 and later). See bulletins SB-0318 and IS-0319 for service kit information.
100_014C
Mower Decks Lastec//080216 4-33
Mower DecksSingle Pulley Spindle, Decks 3 (Serial #46331112 and later)4
4.17 Single Pulley Spindle, Decks 3 (Serial #46331112 and later)
REF PART # DESCRIPTION COMMENTS QTY.
072625 Spindle Assembly, EZT 21" D6.3 Spacer Non-saleable item. Parts must be purchased separately.
1
1 P107 1
1 For service order 067354 Spindle Bolt 1 1/4” Service Kit including (1) P107 1/4-28 Straight Grease Fitting and (1) 045677 Spindle Single Pulley Bolt.
Fitting, 1/4-28 Straight Grease 1
2 0456771 Bolt, Spindle Single Pulley Maximum Torque: 57 ft-lbs 1
3 F05011-97 Washer, 1/2” Plain Belleville 1
4 072628 Key, 1/4” Square x 1-1/4” Long 1
5 072626 Sheave, Single - D6.3 B1.00 Cast 1
6 F05007-78 Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5 4
7 067696 Spindle Assembly, ZT Cast See Section 4.3 for parts 1
8 F05010-222 Nut, 3/8-16 Flanged Hex Nyloc 4
9 P128 Blade, 21” x 2 1/2” x 1/4” High Lift 1
P246 Blade, 21” Low-Lift Optional 1
P322 Blade, 21” Gator Mulching Optional 1
063265 Blade, 21” x 2 1/2” x 1/8” Low-Lift Ultra Optional 1
10 064198 Stiffener Weldment, Blade E-Series 1
11 029889 Washer, 2 1/2” x 11/16” x 3/16” Nylon 1
12 F05011-89 Washer, 2 1/2” OD x 5/8” ID x 3/16” Std Flat Znc Remove to install Anti-Scalp Blade Disc
1
13 F05009-95 Bolt, 5/8-18 x 1 3/4” Hex Head Grade 5 Torque Value: 75 ft-lbs 1
14 048898 Blade Disc, Anti-Scalp Optional part. Remove Item 13 to install Anti-Scalp Blade Disc
1
4-34 Lastec//080216 Mower Decks
Mower DecksSingle Pulley Spindle, Decks 3 (Serial #46331112 and later) 4
100_206
Mower Decks Lastec//080216 4-35
Mower DecksSpindle Assembly, Deck 3 (Prior to Serial #46331112)4
4.18 Spindle Assembly, Deck 3 (Prior to Serial #46331112)
REF PART # DESCRIPTION COMMENTS QTY.
063276 Spindle Assembly, Single Sheave w/Anti Non-saleable item. Parts must be purchased separately.
1
1 P107 1
1 P107 replaced P04107 3/16” x 3/16” Straight Grease Fitting to improve durability (Serial #41071011 and later).
Fitting, 1/4-28 Straight Grease 1
2 059142 Bolt, Spindle Pulley 1/2-13 x 1 3/4” Maximum Torque: 57 ft-lbs 1
3 F05011-97 Washer, 1/2” Plain Belleville 1
4 S04124 Key, 1/4” x 1 11/16” 1
5 034953 Sheave, Single - 2561 Mower 1
6 043249 Washer, 3/8” x 1.5” x 1.01” 1
7 046273 Washer, 1/4” x 1.47” x 1.01” 1
8 F05007-85 Bolt, 3/8-16 x 1 1/2” Carriage Grade 5 4
9 044862 Plate, Deck Reinforcing 2
10 034954 Spindle Assembly, w/Stiffener See Section 4.19 for parts 1
11 F05010-10 Nut, 3/8-16 Hex Nyloc 4
12 P128 Blade, 21” x 2 1/2” x 1/4” High Lift 1
P246 Blade, 21” Low-Lift Optional 1
P322 Blade, 21” Gator Mulching Optional 1
063265 Blade, 21” x 2 1/2” x 1/8” Low-Lift Ultra Optional 1
13 064198 Stiffener Weldment, Blade E-Series 1
14 028254 Channel, Blade Stiffener 1
15 F05011-27 Washer, 5/8” Split Lock 1
16 F05009-95 Bolt, 5/8-18 x 1 3/4” Hex Head Grade 5 Torque Value: 75 ft-lbs 1
17 048898 Blade Disc, Anti-Scalp Optional 1
4-36 Lastec//080216 Mower Decks
Mower DecksSpindle Assembly, Deck 3 (Prior to Serial #46331112) 4
TR1006B
Mower Decks Lastec//080216 4-37
Mower DecksSpindle Housings, Deck 3 (Prior to Serial #46331112)4
4.19 Spindle Housings, Deck 3 (Prior to Serial #46331112)
Concerning Sealed Bearings:
One of the most common misconceptions that cause a high number of bearing failures is that a bearing needs to be completely packed full. Many people have been taught; the more grease, the better. We have even heard of cases where people do not feel bear-ing manufacturers use enough grease in sealed and shielded ball bearings, so they remove one seal or shield and pack the bearing with more grease. These miscon-ceptions are completely false.
Nachi standard grease fill for sealed and shielded ball bearings is 20% to 30% full
Too much grease can cause excess friction, thereby overheating the bearing and causing remature failure.
Only a small of grease is required to lubricate a bearing in motion.
When a bearing is in motion, most of the grease is pushed to the side (channeling) leaving a thin film of oil between the raceways and rolling elements.
REF PART # DESCRIPTION COMMENTS QTY.
034954 Spindle Assembly, w/Stiffener Non-saleable item. Parts must be purchased separately.
1
1 F05006-140 Bolt, 5/16-18 x 5” Hex Head Grade 5 3
2 F05006-93 Bolt, 5/16-18 x 1” 1/4 Hex Head Full Thread Grade 5 3
3 F05011-13 Washer, 5/16” Split Lock 3
4 034921 Plate, Deck Reinforcing 1
5 034969 Seal, 2561 Spindle 1
6 034951 Collar, Spindle Top 1
7 062999 O-Ring, Spindle Added after serial # 34990809 1
8 P11035 Bearing, 6206-2NSE 3
9 034945 Housing, Spindle 1
10 F05012-64 Pin, 1/8” x 1/2” Roll 1
11 F05010-58 Nut, 5/16-18 Nylok Hex 3
12 034950 Spacer, Spindle Bearing 1
13 F04254-45 O-Ring, 2 7/16"ID x 3/16" Diameter 2
14 034947 Washer, 1.50” x 1.185” x 16Ga 1
15 034948 Washer, 2.435” x 1.185” x 11Ga 1
16 034946 Shaft, Blade Spindle 1
4-38 Lastec//080216 Mower Decks
Mower DecksSpindle Housings, Deck 3 (Prior to Serial #46331112) 4
100_033
Mower Decks Lastec//080216 4-39
Mower DecksAnti-Scalp Rollers4
4.20 Anti-Scalp Rollers
REF PART # DESCRIPTION COMMENTS QTY.
059189 Roller Assembly, Anti-Scalp 1
1 019900 Axle Rod, 425D Anti-Scalp Roller 1
2 P438 Wheel, Anti-Scalp 6” x 3.25” x 3/4” ID 2
3 061651 Spacer, Anti-Scalp 1
4 F05010-79 Nut, 1/2-20 Jam Nyl Lock 2
5 F05011-2 Washer, 1/2” SAE Flat 6
6 059191 Link Arm, Anti-Scalp 1
7 F05008-33 Bolt, 1/2-13 x 1 1/2” Hex Head Grade 5 2
8 F05008-37 Bolt, 1/2-13 x 1 1/4” Hex Head Grade 5 2
9 F05010-185 Nut, 5/8-11 FlexLoc 2
10 F05009-116 Bolt, 5/8-11 x 2” Carriage Grade 5 2
11 059190 Frame Weldment, Anti-Scalp 1
4-40 Lastec//080216 Mower Decks
Mower DecksAnti-Scalp Rollers 4
TR1012
Mower Decks Lastec//080216 4-41
Mower DecksPull Pivot Assembly4
4.21 Pull Pivot Assembly
REF PART # DESCRIPTION COMMENTS QTY.
059195 Pivot Assembly, Pull 1
1 F05007-131 Bolt, 3/8-16 x 1 1/4” Whiz Lock 2
2 059193 Pin Weldment, Deck Pivot 1
3 P109 Bushing, 1” ID x 1 1/4” OD x 1 1/4” Flanged 2
4 059279 Pivot Weldment, Deck Raise 1
5 F05008-88 Bolt, 1/2-13 x 1 3/4” Hex Head Grade 5 1
6 059199 Rod Assembly, 1/4” Deck Lift See Section 4.22 for parts 1
7 F05010-79 Nut, 1/2-20 Jam Nyl Lock 1
8 P107 Fitting, 1/4-28 Straight Grease 2
9 059196 Pin Weldment, Pull 1
4-42 Lastec//080216 Mower Decks
Mower DecksPull Pivot Assembly 4
TR1011-1B
Mower Decks Lastec//080216 4-43
Mower DecksDeck 3 Rod Assembly4
4.22 Deck 3 Rod Assembly
REF PART # DESCRIPTION COMMENTS QTY.
059199 Rod Assembly, 1/4” Deck Lift 1
1 019348 Rod End, 1/2-20 Female 1
2 F05010-16 Nut, 1/2-20 Hex Jam 1
3 019701 Rod Weldment, E1-E3 Deck Lock 1
4 019650 Spacer, 1/4” Thk Deck Height 12
5 019650-1 Spacer, 1/4” Thk Knurled 4
6 041631 Spring, .72” x 1.5” x .063” Compression 1
7 F05011-2 Washer, 1/2” SAE Flat 1
8 F05010-79 Nut, 1/2-20 Jam Nylon Lock 1
4-44 Lastec//080216 Mower Decks
Mower DecksDeck 3 Rod Assembly 4
TR1011-2
Mower Decks Lastec//080216 4-45
Mower DecksGrass Discharge Deck 34
4.23 Grass Discharge Deck 3
REF PART # DESCRIPTION COMMENTS QTY.
1 F05010-10 Nut, 3/8-16 Hex Nyloc 1
2 028141 Washer, Gearbox Keeper 1
3 061650 Deflector, #3 Rubber 1
4 F05011-3 Washer, 3/8” Flat SAE 2
5 061648 Clamp Plate, #3 Rubber 1
6 F05007-124 Bolt, 3/8-16 x 2” Hex Head Grade 5 2
059082 Deflector Assembly, Grass 1
7 059081 Deflector Plate, #5 Deck Grass 1
8 F05007-165 Bolt, 3/8-16x1 Carriage 2
9 F05010-222 Nut, 3/8-16 Flanged Hex Nylock 2
4-46 Lastec//080216 Mower Decks
Mower DecksGrass Discharge Deck 3 4
TR1018-1B
Mower Decks Lastec//080216 4-47
Mower DecksDeck 4 Hardware4
4.24 Deck 4 Hardware
CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.
REF PART # DESCRIPTION COMMENTS QTY.
1 F81033-6 Nut, 10mm x 1.25 Nylon Metric 1
2 F05010-192 Nut, M10-1.25 Free Zinc Plate Metric 1
3 F05004-277 Bolt, M10-1.25 x 40mm Hex Head Grade 8.8 Metric 1
4 F05009-35 Bolt, 5/8-11 x 2 3/4” Hex Head Grade 5 3
5 049870 Bushing, Urethane Pivot 4
6 F05011-40 Washer, 5/8” Standard Flat 2
7 F05010-185 Nut, 5/8-11 FlexLoc 4
8 059170 Hinge Weldment, #4 Deck 1
9 F05008-74 Bolt, 1/2-13 x 2 1/2” Hex Head Grade 5 2
10 F05011-9 Washer, 1/2” Split Lock 1
11 059078 Tube, Belt Keeper 1
12 F05009-41 Bolt, 5/8-11 x 1 1/2” Hex Head Full Thread Grade 5 1
13 061855 Spacer, Bearing 1
14 061856 Bearing, 1.25” x 2.25” x .50” 1
15 F05011-5 Washer, 5/8” SAE Flat 1
16 F05010-96 Nut, 5/8-11 Jam Nyl Lock 1
17 F05008-33 Bolt, 1/2-13 x 1 1/2” Hex Head Grade 5 1
18 018751 Washer, Motor Mount 1
19 F05010-127 Nut, 1/2-13 Half Nyloc 2
20 F05009-20 Bolt, 5/8-11 x 2 1/2” Hex Head Grade 5 1
21 F05010-8 Nut, 1/2-13 Nyl Hex Lock 2
22 F05008-134 Bolt, 1/2-13 x 3 1/4” Hex Head Grade 5 1
23 062149 Sleeve, .875” x 1.14” Lg Bushing 2
24 062115 Bushing, .875” Bearing 2
25 057505 Bolt, 5/16-18 x 2” Elevator 1
26 F05011-13 Washer, 5/16” Split Lock 1
27 F05010-17 Nut, 5/16-18 Hex 1
4-48 Lastec//080216 Mower Decks
Mower DecksDeck 4 Hardware 4
TR1019-1B
Mower Decks Lastec//080216 4-49
Mower DecksDeck 4 Covers4
4.25 Deck 4 Covers
REF PART # DESCRIPTION COMMENTS QTY.
059711 Cover Assembly, #4 Pivoting 1
1 059712 Cover, #5 Deck Sliding 1
2 059083 Bumper, Rubber Button 4
3 059713 Cover, #4 Deck Sliding 1
4 F05010-121 Nut, 5/16-18 Nylon Locking Jam 4
5 F05011-17 Washer, 5/16” SAE Flat 4
6 F05015-36 Screw, #10 x 1/2” Long AB Thrd Slot Hex Head 8
7 058597 Hinge, 521E Sliding Cover 1
8 058844 Pivot Bearing, Cover 2
9 F05006-15 Bolt, 5/16-18 x 1/2” Hex Head Grade 5 4
059169 Cover Assembly, #4 Deck Pivoting 1
10 059173 Cover Plate, Right 1
11 F05006-102 Bolt, 5/16-18 x 3/4” Hex Head Grade 5 6
12 F05011-13 Washer, 5/16” Split Lock 6
13 F05011-17 Washer, 5/16” SAE Flat 6
14 067043 1
1 Replaced 043217 1-1/4” Hole Plug Cover. Deck cover was redesigned to accept 1-3/8” hole plug cover (7/11).
Cover, 1 3/8”” Hole Plug 1
15 061840 Guard Weldment, #4 Rear 1
16 061839 Guard Weldment, #4 Front 1
064574 2
2 Replaced 059180 #4 Trap Door Assembly including (3) F05006-102 5/16-18 x 3/4” Hex Head Bolt, (3) F05011-13 5/16” Split Lock Washer, 059179 #4 Deck Trap Door Clamp Plate and 059178 #4 Deck Trap Door (9/11).
Door Assembly, #4 Deck Trap 1
17 F05006-27 Bolt, 5/16-18 x 1” Hex Head Grade 5 4
18 F05011-13 Washer, 5/16” Split Lock 4
19 064576 Clamp Plate, #4 Trap Door 1
20 064575 Door, #4 Deck Trap 1
059082 Deflector Assembly, Grass 1
21 059081 Deflector Plate, #5 Deck Grass 1
22 F05007-165 Bolt, 3/8-16x1 Carriage 2
23 F05010-222 Nut, 3/8-16 Flanged Hex Nylock 2
064577 3
3 067376 replaced 064578 #4 Deck Trap Door, removed 064579 Clamp Plate and added (2) F05011-50 Washers (2/12).
Door Assembly, #4 Deck Trap Added (9/11) 1
24 F05006-102 Bolt, 5/16-18 x 3/4” Hex Head 2
25 F05011-13 Washer, 5/16” Split Lock 2
26 F05011-50 Washer, 5/16” x 1 1/4” Fender 2
27 067376 Door, #2/4 Deck Trap 1
064580 Baffle Assembly, #4 Blowout Added (9/11) 1
28 064581 Baffle Weldment, #4 Blowout 1
29 F05006-86 Bolt, 5/16-18 x 3/4” Carriage 2
30 F05010-121 Nut, 5/16-18 Nylon Locking Jam 2
4-50 Lastec//080216 Mower Decks
Mower DecksDeck 4 Covers 4
TR1019-2D
Mower Decks Lastec//080216 4-51
Mower DecksDeck 5 Hardware4
4.26 Deck 5 Hardware
REF PART # DESCRIPTION COMMENTS QTY.
1 F05010-121 Nut, 5/16-18 Nylon Locking Jam 3
2 046293 Washer, Throttle Friction 2
3 F05010-58 Nut, 5/16-18 Nylok Hex 1
4 061844 Cover Weldment, #5 1
5 F05011-17 Washer, 5/16” SAE Flat 1
6 067043 1
1 Replaced 043217 1-1/4” Hole Plug Cover. Deck cover was redesigned to accept 1-3/8” hole plug cover (7/11).
Cover, 1 3/8”” Hole Plug 1
7 F81003-25 Bolt, M10-1.25 x 30mm Hex Head FT 8.8 Metric 1
8 F05010-192 Nut, M10-1.25 Free Zinc Plate Metric 1
9 046465 Dampener, Hand Control 1
10 F81033-6 Nut, 10mm x 1.25 Nylon Metric 1
11 F05008-74 Bolt, 1/2-13 x 2 1/2” Hex Head Grade 5 2
12 F05009-20 Bolt, 5/8-11 x 2 1/2” Hex Head Grade 5 2
13 F05010-8 Nut, 1/2-13 Nyl Hex Lock 2
14 F05010-185 Nut, 5/8-11 FlexLoc 2
059082 Deflector Assembly, Grass 1
15 059081 Deflector Plate, #5 Deck Grass 1
16 F05007-165 Bolt, 3/8-16x1 Carriage 2
17 F05010-222 Nut, 3/8-16 Flanged Hex Nylock 2
18 063278 Spindle Assembly, Dbl Sheave Low w/ Anti See Section 4.4 for parts 1
19 057111 Idler Assembly, 521EH High See Section 4.27 for parts 1
20 061616 Chute Assembly, #5 Deck Grass See Section 4.28 for parts 1
21 041630 Belt, Insta-Power 85830 1
22 061843 Rocker Assembly, Right See Section 4.6 for parts 1
4-52 Lastec//080216 Mower Decks
Mower DecksDeck 5 Hardware 4
TR1020B
Mower Decks Lastec//080216 4-53
Mower DecksDeck 5 Idler4
4.27 Deck 5 Idler
REF PART # DESCRIPTION COMMENTS QTY.
057111 Idler Assembly, 521EH High 1
1 F05008-10 Bolt, 1/2-13 x 2 1/4” Hex Head Grade 5 2
2 062051 Washer, Water Shed Pulley 2
105249 Pulley Assembly, 5In OD Idler, V Groove Tall 1
3 F04254-12 Ring, 62mm IR Din #472 Retaining 2
4 P103 Bearing, Spindle Top 6305 RS 1
5 045270 Pulley, 5” OD Idler, V Groove 1
6 045297 Boss, Idler Pulley Standoff 1
7 056566 Weldment, 521E Idler Plate 1
8 P123 Fitting, Grease 90 Deg. 1/4-28 1
9 F05010-127 Nut, 1/2-13 Half Nylon Lock 2
10 029842 Bushing, 3/4” ID x 1” OD x 1” Oil 2
11 F05010-122 Nut, 3/4-10 Half Nylon Lock 1
12 F05011-77 Washer, 3/4” AN Yel/Cad 1
045295 Pulley Assembly, 5” OD Idler, Flat 1
13 F04254-12 Ring, 62mm IR Din #472 Retaining 2
14 P103 Bearing, Spindle Top 6305 RS 1
15 045296 Pulley, 5” OD Idler, Flat 1
16 045297 Boss, Idler Pulley Standoff 1
17 F05006-76 Bolt, 5/16-18 x 1 1/2” Hex Head Full Thread Grade 5 1
18 F05010-17 Nut, 5/16-18 Hex 1
19 F05010-221 Nut, 5/16-18 Flanged Hex Nylock 1
20 P410 Spring, 1” x 7” Extension 1
21 F05011-68 Washer, 1/2 Standard Flat 2
4-54 Lastec//080216 Mower Decks
Mower DecksDeck 5 Idler 4
100_010C
Mower Decks Lastec//080216 4-55
Mower DecksRear Grass Discharge Deck 54
4.28 Rear Grass Discharge Deck 5
REF PART # DESCRIPTION COMMENTS QTY.
061616 Chute Assembly, #5 Deck Grass 1
1 F05010-221 Nut, 5/16-18 Flanged Hex Nylock 9
2 F05006-90 Bolt, 5/16-18 x 1” Carriage Grade 5 5
3 062145 Support Plate, Chute Side 1
4 061615 Chute, #5 Right Rubber Grass 1
5 062118 Support Plate, Chute Top 1
6 061614 Chute Tab, Inside Rubber 1
7 061611 Support Plate, Chute Top 1
8 F05006-141 Bolt, 5/16-18 x 1” BHCS SS 2
9 F05011-50 Washer, 5/16” x 1 1/4” Fender 4
10 F05006-153 Bolt, 5/16-18 x 1-1/2 Carriage Grade 5 2
4-56 Lastec//080216 Mower Decks
Mower DecksRear Grass Discharge Deck 5 4
LT0088C
Mower Decks Lastec//080216 4-57
Mower DecksDeck Wheel Assembly4
4.29 Deck Wheel Assembly
NOTE: Deck 2 (059274) and deck 4 (059273) wheel assemblies are mirror images of each other, with the exception of items 8 and 11.
REF PART # DESCRIPTION COMMENTS QTY.
059274 Wheel Assembly, Left Shortened Deck 2 1
059273 Wheel Assembly, Right Shortened Deck 4 1
1 F05010-124 Nut, 3/8-16 Half Nyloc 2
2 F05011-3 Washer, 3/8” SAE Flat 3
3 028141 Washer, Motor Mount 2
4 F05007-210 Bolt, 3/8-16 x 3” Hex Head Grade 8 1
5 067776 Strap Assembly, Deck Support Serial #48400513 and later 2
062114 Cable, Deck Support Prior to Serial #48400513 2
6 059299 Spring, Counter Balance 1
7 F05010-127 Nut, 1/2-13 Half Nylon Lock 1
8 059275 Weldment, Left Shortened Wheel Deck 2 1
059175 Weldment, Right Shortened Wheel Deck 4 1
9 P107 Fitting, 1/4-28 Straight Grease 1
10 F05010-185 Nut, 5/8-11 FlexLoc 3
11 059163 Lock Weldment, Left Wheel Deck 2 1
059177 Lock Weldment, Right Wheel Deck 4 1
12 F05010-177 Nut, 3/4-10 Stover Swaged 1
13 F05009-104 Bolt, 3/4-10 x 6” Carriage Grade 5 1
14 F05009-116 Bolt, 5/8-11 x 2” Carriage Grade 5 2
15 P296 Spacer, 1.13” OD x .75” ID x .5” 1
16 061826 Wheel Assembly, 9” x 3.5” Solid DM 1
17 042898 Spacer, 3/4” Axle Bolt 1
18 F05008-88 Bolt, 1/2-13 x 1 3/4” Hex Head Grade 5 1
19 061853 Rod Assembly, Rear Wheel See Section 4.31 for parts 1
20 019650 Spacer, 1/4” Thk Deck Height 1
21 F05010-79 Nut, 1/2-20 Jam Nylon Lock 1
22 062115 Bushing, .875” Bearing 4
23 062149 Sleeve, .875” x 1.14” Long Bushing 4
4-58 Lastec//080216 Mower Decks
Mower DecksDeck Wheel Assembly 4
TR1013-1B
Mower Decks Lastec//080216 4-59
Mower DecksRear Wheel Hanger Assembly (Optional)4
4.30 Rear Wheel Hanger Assembly (Optional)
REF PART # DESCRIPTION COMMENTS QTY.
067310 Hanger Assembly, 100EZT Rear Wheel 1
1 067308 Hanger Weldment, 100EZT Rear Wheel 1
2 067309 Chain, 5/16” x 6” Links 1
3 F05007-78 Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5 1
4 F05010-10 Nut, 3/8-16 Hex Nyloc 1
5 P438 Wheel, Anti-Scalp 6” x 3.25” x 3/4”ID 1
4-60 Lastec//080216 Mower Decks
Mower DecksRear Wheel Hanger Assembly (Optional) 4
100_170
Mower Decks Lastec//080216 4-61
Mower DecksWheel Lift Rod Assembly4
4.31 Wheel Lift Rod Assembly
REF PART # DESCRIPTION COMMENTS QTY.
061853 Rod Assembly, Rear Wheel 1
1 019348 Rod End, 1/2-20 Female 1
2 F05010-16 Nut, 1/2-20 Hex Jam 1
3 019701 Rod Weldment, E1-E3 Deck Lock 1
4 019651 Spacer, 5/16” Thk Deck Height 10
5 019651-1 Spacer, 5/16” Thk Knurled 3
6 041631 Spring, .72” x 1.5” x .063” Compression 1
7 F05011-2 Washer, 1/2” SAE Flat 1
8 F05010-15 Nut, 1/2-20 Nyl Hex Lock 1
4-62 Lastec//080216 Mower Decks
Mower DecksWheel Lift Rod Assembly 4
TR1013-2
Mower Decks Lastec//080216 4-63
Mower DecksWheel Yoke Assembly4
4.32 Wheel Yoke Assembly
REF PART # DESCRIPTION COMMENTS QTY.
061832 Yoke Assembly, Pivoting Wheel 1
061834 Wheel Yoke Assembly, 9” 1
1 P116 Washer, 1-1/16” x 1-3/4” x 1/8” 2
2 F05011-116 Washer, 1” ID .06 SS Shim 1
3 F05011-115 Washer, 1” ID .03 SS Shim 1
4 063216 Spring, Wheel Yoke 1-0 Urethane 1
5 T104 Spacer, 1” ID x 1-3/4” OD x 1/4” 2
6 T107 Spacer, 1 3/4” OD x 1 1/16” ID x 1” 3
7 P109 Bushing, 1” ID x 1-1/4” OD x 1-1/4” Flanged 2
8 067076 Pin, 3/8” Dia Lynch Locking 1
9 061833 Yoke Weldment, 9” 1
10 F05009-104 Bolt, 3/4-10 x 6” Carriage Grade 5 1
11 042898 Spacer, 3/4” Axle Bolt 2
12 061826 Wheel Assembly, 9” x 3.5” Solid DM See Section 4.8 for parts 1
13 F05011-62 Washer, 3/4” SAE Flat 1
14 F05010-177 Nut, 3/4-10 Stover Swaged 1
15 F05010-8 Nut, 1/2-13 Nylon Hex Lock 1
16 F05011-2 Washer, 1/2” SAE Flat 2
072931 Service Yoke Assembly, Pivoting Wheel 1
17 059183 Yoke Weldment, Pivoting Order 072931 for Service 1
P109 Bushing, 1” ID x 1-1/4” OD x 1-1/4” Flanged 2
18 P107 Fitting, 1/4-28 Straight Grease 1
19 F05008-23 Bolt, 1/2-13 x 3” Hex Head Grade 5 1
20 F05010-10 Nut, 3/8-16 Hex Nyloc 1
21 F05011-3 Washer, 3/8” Flat SAE 2
22 F05007-73 Bolt, 3/8-16 x 3” Hex Head Grade 5 1
23 029895 Pin, 1/2” Dia x 3 1/2” Snap Spring 1
24 059187 Bushing, Urethane Spring 1
4-64 Lastec//080216 Mower Decks
Mower DecksWheel Yoke Assembly 4
TR1010
Mower Decks Lastec//080216 4-65
Mower DecksDeck Lift Cylinder Assembly4
4.33 Deck Lift Cylinder Assembly
REF PART # DESCRIPTION COMMENTS QTY.
072935 Cylinder Assembly, #4 Deck Lift Deck #4 1
072934 Cylinder Assembly, #2 Deck Lift Deck #2 1
1 016292 1
1 067325 replaced (1) 061941 Hydraulic Cylinder Large Chain Weldment and 016292 replaced (1) F05010-178 3/4-10 Flexloc Nut to improve durability (serial #41081011 and later).
Pin, 7/16” Dia Lynch Locking 1
2 0673251 Chain, 5/16” x 5 Links 1
3 F05010-10 Nut, 3/8-16 Hex Nylock 1
4 F05010-96 Nut, 5/8-11 Jam Nyl Lock 2
5 F05011-5 Washer, 5/8” SAE Flat 1
6 F05010-118 Nut, 1-14 Hex Jam 1
7 058599 Block, Hydraulic Cylinder Pivot 1
8 058598 Lock Plate, Hydraulic Cylinder 1
9 F05011-13 Washer, 5/16” Split Lock 4
10 F05006-27 Bolt, 5/16-18 x 1” Hex Head Grade 5 4
11 P107 Fitting, 1/4-28 Straight Grease 1
12 F05007-78 Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5 Deck #4 1
F05007-119 Bolt, 3/8-16 x 1 3/4” Hex Head Grade 5 Deck #2 1
13 F05009-125 Bolt, 5/8-11 x 4 1/2” Hex Head Grade 8 1
14 058530 Cylinder, Hyd. Deck Lift 1
15 059293 Pin, 1/2” Dia x 2 1/2” Detent 1
16 059120 Lock Weldment, Deck Latch 1
17 061858 Switch Plate, Hydraulic Cylinder 1
18 061845 Switch, Sealed w/Lead 1
19 F05004-95 Screw, 6-32 x 7/8 Round Head Phillips 2
20 F05010-59 Nut, #6-32 Keps 2
061851 Fitting, 1/4” MPT 90 Deg, w/Orifice Port Not Shown 4
040143 Orifice, 5/16” OD x .040” ID x 3/8” Not Shown 2
4-66 Lastec//080216 Mower Decks
Mower DecksDeck Lift Cylinder Assembly 4
100_226
Mower Decks Lastec//080216 4-67
Mower DecksHydraulic Hoses4
4.34 Hydraulic Hoses
REF PART # DESCRIPTION COMMENTS QTY.
059970 Hose Kit, Toro 100ZT Hydraulic 2
1 059979 Abrasion Sleeve, 19 5/8” Hydraulic Hose 2
2 059967 Hose, 21" OFS-04 High Pressure Hydraulic 2
3 059980 Abrasion Sleeve, 30 1/4” Hydraulic Hose 1
4 059968 Hose, 32" OFS-04 High Pressure Hydraulic 1
5 059981 Abrasion Sleeve, 51 3/4” Hydraulic Hose 1
6 059969 Hose, 53 1/2" OFS-04 High Pressure Hydraulic 1
4-68 Lastec//080216 Mower Decks
Mower DecksHydraulic Hoses 4
Retract
Retract
Extend
Extend
To Foot Valve
To Foot Valve
To Foot Valve
To Foot Valve
To Right Cylinder
To Right Cylinder
To Left Cylinder
To Left Cylinder
TR1022
059965
To Pump To Oil Cooler
H supplied by ose Toro059969
059967
Mower Decks Lastec//080216 4-69
Mower//080216 5-1
5
SECTION 5 INDEX
Part Number Index
015460, Grommet, 11/16 x 1 x 1 5/16 Rubber 2-10016292, Pin, 7/16” Dia Lynch Locking 4-66018751, Washer, Motor Mount 2-6, 4-24, 4-32, 4-48018894, Bushing, 1 1/2” ID x 1 3/4” OD x 1 1/2” Lg
Bronze 2-6019348, Rod End, 1/2-20 Female 4-18, 4-44, 4-62019535, Spacer, 3/8” Deck Lift 425 Yzc 4-32019650, Spacer, 1/4” Thk Deck Height 4-44, 4-58019650-1, Spacer, 1/4” Thk Knurled 4-44019651, Spacer, 5/16” Thk Deck Height 4-62019651-1, Spacer, 5/16” Thk Knurled 4-62019701, Rod Weldment, E1-E3 Deck Lock 4-44, 4-62019900, Axle Rod, 425D Anti-Scalp Roller 4-40024155, Clamp, 1/4" Wire 13/32 Mtg Hole 4-26027053, Key, 1/4” x 2 1/2” 4-8, 4-30028080, Key, 1/4” Square x 1 1/2” Long 4-4, 4-28028141, Washer, Gearbox Keeper 4-46028141, Washer, Motor Mount 4-58028254, Channel, Blade Stiffener 4-4, 4-8, 4-28, 4-30,
4-36029109, Spacer, 3/16 Thk Deck Height 2-6029109, Spacer, 3/16” Thk Deck Height 4-18029109-1, Spacer, 3/16” Thk Knurled 4-18029214, Spacer, 1.00” OD x .41” ID x 1/4” Nylon 2-4029842, Bushing, 3/4” ID x 1” OD x 1” Oil 3-2, 4-20,
4-54029889, Washer, 2 1/2” x 11/16” x 3/16” Nylon 4-34029895, Pin, 1/2” Dia x 3 1/2” Snap Spring 4-64034921, Plate, Deck Reinforcing 4-10, 4-38034945, Housing, Spindle 4-10, 4-38034946, Shaft, Blade Spindle 4-38034947, Washer, 1.50 x 1.185 x 16Ga 4-38034947, Washer, 1.50” x 1.185” x 16Ga 4-6, 4-10034948, Washer, 2.435 x 1.185 x 11Ga 4-38034948, Washer, 2.435” x 1.185” x 11Ga 4-6, 4-10034950, Spacer, Spindle Bearing 4-10, 4-38034951, Collar, Spindle Top 4-10, 4-38034953, Sheave, Single - 2561 Mower 4-36034954, Spindle Assembly, w/Stiffener 4-36, 4-38034969, Seal, 2561 Spindle 4-10, 4-38040049, Sheave, Double - 2561 Mower 4-8, 4-30040143, Orifice, 5/16” OD x .040” ID x 3/8” 4-66041192, Clip, Handle Deck 2-10041193, Bracket, Deck Bar Holder 2-10041206-toro, Decal, Caution Symbol CE Std -Toro 1-4041630, Belt, Insta-Power 85830 1-6, 4-2, 4-52041631, Spring, .72” x 1.5” x .063” Compression 4-18,
4-44, 4-62041685, Handle Assembly, 421D Deck Lift 2-10
042898, Spacer, 3/4” Axle Bolt 4-14, 4-58, 4-64043224-toro, Decal, Equipment, Height Adj EF -Toro
1-4043245, Shaft, Center Blade Spindle 4-10043246, Spindle Assembly, Center w/Stiffener 4-8,
4-10, 4-30043249, Washer, 3/8” x 1.5” x 1.01” 4-30, 4-36044862, Plate, Deck Reinforcing 4-8, 4-30, 4-36045270, Pulley, 5” OD Idler, V Groove 4-20, 4-54045295, Pulley Assembly, 5” OD Idler, Flat 3-2, 4-20,
4-32, 4-54045296, Pulley, 5” OD Idler, Flat 3-2, 4-20, 4-32, 4-54045297, Boss, Idler Pulley Standoff 3-2, 4-20, 4-32,
4-54045677, Bolt, Spindle Pulley 4-8045677, Bolt, Spindle Single Pulley 4-4, 4-34046273, Washer, 1/4” x 1.47” x 1.01” 4-8, 4-30, 4-36046293, Washer, Throttle Friction 4-2, 4-52046465, Dampener, Hand Control 3-2, 4-2, 4-52048455, Spacer, 3/4” Wheel Bearing 4-16048644, Handle, Foam .625 x 6 x 3/16 Wall 2-10048898, Blade Disc, Anti-Scalp 4-8, 4-30, 4-34, 4-36049868, Spacer, .53”ID x 1 1/4” OD x 1 1/4” Long 4-12049870, Bushing, Urethane Pivot 4-24, 4-32, 4-48050436, Relay, 40A 12VDC Automotive 2-2055430-toro, Decal, Rear Tire Pressure - Toro 1-4056565, Idler Assembly, 521 4-20056566, Weldment, 521E Idler Plate 4-20, 4-54057111, Idler Assembly, 521EH High 4-52, 4-54057333, Strap, Two Channel Plastic 2-4057505, Bolt, 5/16-18 x 2” Elevator 4-24, 4-48057524-toro, Decal, 100” - Toro 1-4057530-toro, Decal, Foot Valve Ops - Toro 1-4057531-toro, Decal, No Step - Toro 1-4057532-toro, Decal, Deck Lock - Toro 1-4057533-toro, Decal, Caution, Rotating Parts - Toro 1-4057534-toro, Decal, Caution, Hand Pinch - Toro 1-4057535, Decal Kit, Toro 100 1-4058336, Rod Assembly, 521 ZT Rocker Spacer 4-12058336, Rod Assembly, 521ZT Rocker Spacer 4-18058341, Plate, 521 Rocker Tube Limit 4-12058530, Cylinder, Hyd. Deck Lift 4-66058597, Hinge, 521E Sliding Cover 4-26, 4-50058598, Lock Plate, Hydraulic Cylinder 4-66058599, Block, Hydraulic Cylinder Pivot 4-66058844, Pivot Bearing, Cover 4-26, 4-50059005, Valve Assembly, 100ZT Lift 2-8059005, Valve Assembly, Toro ZT Lift 2-4059078, Tube, Belt Keeper 4-24, 4-48
i Lastec//080216 Index
Part Number Index
059081, Deflector Plate, #5 Deck Grass 4-2, 4-26, 4-46, 4-50, 4-52
059082, Deflector Assembly, Grass 4-2, 4-26, 4-46, 4-50, 4-52
059083, Bumper, Rubber Button 4-26, 4-50059096, Door, #1 Deck Trap 4-2059105, Yoke Weldment, 9” w/6” Shaft 4-14059120, Lock Weldment, Deck Latch 4-66059125, Clamp Plate, #1 Deck Trap Door 4-2059126, Door Assembly, #1 Deck Trap 4-2059133, Cover Plate, Left 4-26059142, Bolt, Spindle Pulley 1/2-13 x 1 3/4” 4-30, 4-36059142, Bolt, Spindle Pulley 1/2-13 x 1-3/4 4-28059163, Lock Weldment, Left Wheel 4-58059168, Hinge Weldment, #2 Deck 4-24059169, Cover Assembly, #4 Deck Pivoting 4-50059170, Hinge Weldment, #4 Deck 4-48059173, Cover Plate, Right 4-50059175, Weldment, Right Shortened Wheel 4-58059177, Lock Weldment, Right Wheel 4-58059183, Yoke Weldment, Pivoting 4-64059187, Bushing, Urethane Spring 4-64059189, Roller Assembly, Anti-Scalp 4-40059190, Frame Weldment, Anti-Scalp 4-40059191, Link Arm, Anti-Scalp 4-40059193, Pin Weldment, Deck Pivot 4-42059195, Pivot Assembly, Pull 4-42059196, Pin Weldment, Pull Pin 4-42059199, Rod Assembly, 1/4” Deck Lift 4-42, 4-44059207, Deck Weldment, #2 1-6059208, Deck Weldment, #3 1-6059209, Deck Weldment, #4 1-6059224, Yoke Weldment, 15" Toro Front Wheel 2-6059243, Frame Weldment, Toro 100zt Drive 2-4059255, Axle Weldment, Toro 100zt 2-6059257, Front Axle, Toro Frame 2-4, 2-6059258, Yoke Assembly, 15” Toro Wheel 2-6059259, Wheel ASsembly, Toro 15” x 6-6.00 Air Filled
2-6059259-1, Wheel, 15” x 6-6.00 Air Filled 2-6059260, Frame Assembly, Toro 2-4059273, Wheel Assembly, Right Shortened 4-58059274, Wheel Assembly, Left Shortened 4-58059275, Weldment, Left Shortened Wheel 4-58059279, Pivot Weldment, Deck Raise 4-42059289, Cover Assembly, #2 Deck 4-26059293, Pin, 1/2” Dia x 2 1/2” Detent 4-66059294, Gearbox, Toro (Comer Industries) 3-4059295, Sheave, B Section, 6 1/2” OD Steel 3-4
059299, Spring, Counter Balance 3-2, 4-32, 4-58059702, Tensioner Weldment, Main 3-2059703, Tensioner Assembly, Main Drive 3-2059705, Sheave, 7" OD "B" Section Idler 4-32059706, Pulley Assembly, 7” OD Idler 4-32059707, Drive Belt, B165 Main 1-6059708, Cover Assembly, Left Transition 4-26059709, Cover,#1 Deck Sliding 4-26059710, Cover, #2 Deck Sliding 4-26059711, Cover Assembly, #4 Pivoting 4-50059712, Cover, #5 Deck Sliding 4-50059713, Cover, #4 Deck Sliding 4-50059717, Rocker Weldment, Right 4-12059719, H Block Weldment, Left Rocker 4-12059721, Bushing, 7/8” Bore Taper (w/ Set Screws) 3-4059725, H-Block Weldment, Right Rocker 4-12059797, Door, #2 Deck Trap 4-26059925, Weldment, Toro Footpan 2-10059936, Jack, Toro Unit Service 2-4059940, Footpan Assembly, Toro 100 2-4, 2-10059941, Lock, Toro Footpan 2-10059946, Strap, Jack Tie Down 2-4059948, Grommet, Toro Jack Mount 2-4059950, Arm, Toro Prop-Rod Main 2-4059951, Arm, Toro Prop-Rod Locking 2-4059952, Rod Assembly, Toro Over Center Prop 2-4059953, Serial Number Plate, Toro 2-4059957, Fitting, 90 Degree OFS x ORB 04-06 Hydraulic
2-8059959, Fitting, Branch Tee OFS 04-04-04 Hydraulic
2-8059965, Hose, R16-06 High Pressure Hydraulic 2-8059966, Pedal Weldment, Toro Control Valve Foot 2-8059967, Hose, 21" OFS-04 High Pressure Hydraulic 4-68059968, Hose, 32" OFS-04 High Pressure Hydraulic 4-68059969, Hose, 53 1/2" OFS-04 High Pressure Hydraulic
4-68059970, Hose Kit, Toro 100ZT Hydraulic 4-68059971, Rim, 12” x 10-1/2, Offset w/ Valve Stem 1-8059972, Tire Assembly, 24” x 12-12 w/Toro Offset Rim
1-8059974, Tire, Toro Spec. 24” x 12-12 1-8059977, Plate, Axle Support Hanger 2-6059978, Hanger Assemble, Toro Axle Support 2-4059978, Hanger Assembly, Toro Axle Support 2-6059979, Abrasion Sleeve, 19 5/8” Hydraulic Hose 4-68059980, Abrasion Sleeve, 30 1/4” Hydraulic Hose 4-68059981, Abrasion Sleeve, 51 3/4” Hydraulic Hose 4-68061611, Support Plate, Chute Top 4-56
Index Lastec//080216 ii
Part Number Index
061614, Chute Tab, Inside Rubber 4-56061615, Chute, #5 Right Rubber Grass 4-56061616, Chute Assembly, #5 Deck Grass 4-52, 4-56061621, Rocker , Weldment #1 Trim Deck 4-12061648, Clamp Plate, #3 Rubber 4-46061650, Deflector, #3 Rubber 4-46061651, Spacer, Anti-Scalp 4-40061666, Mount Plate, Rear Guard 1-8061669, Guard Assembly, Rear Bumper 1-8061826, Wheel Assembly, 9” x 3.5” Reliance DM 4-16061826, Wheel Assembly, 9” x 3.5” Solid DM 4-12,
4-14, 4-58, 4-64061826-1, Tire, Carlisle Reliance No-Flat Smooth 4-16061826-2, Hub Assembly, 9/11” Demountable 4-16061826-3, Hub, 9/11” Demountable 4-16061827, Wheel Yoke Assembly, 9” Foam Filled 4-12,
4-14061828, Rocker Assembly, Left Side 4-12061831, Deck Weldment, #1 1-6061832, Yoke Assembly, Pivoting Wheel 4-64061833, Yoke Weldment, 9” 4-64061834, Wheel Yoke Assembly, 9” 4-64061836, Cover, #1 Deck 4-2061837, Guard Weldment, #2 rear 4-26061838, Guard Weldment, #2 Front 4-26061839, Guard Weldment, #4 Front 4-50061840, Guard Weldment, #4 Rear 4-50061842, Deck Weldment, #5 1-6061843, Rocker Assembly, Right 4-12, 4-52061844, Cover Weldment, #5 4-52061845, Switch, Sealed w/Lead 4-66061851, Fitting, 1/4” MPT 90 Deg, w/Orifice Port 4-66061853, Rod Assembly, Rear Wheel 4-58, 4-62061855, Spacer, Bearing 4-24, 4-48061856, Bearing, 1.25” x 2.25” x .50” 4-24, 4-48061858, Switch Plate, Hydraulic Cylinder 4-66061877, Mulching Plate, #5 Deck 1-10061879, Mulching Dam, #3 Toro 1-10061880, Dam Kit, Toro Mulching 1-10062007, Sure Grip, 100zt Top Footpan 2-4062051, Washer, Water Shed Pulley 4-20, 4-32, 4-54062114, Cable, Deck Support 4-58062115, Bushing, .875” Bearing 4-24, 4-48, 4-580621151, Bushing, .875” Bearing 4-12, 4-32062118, Support Plate, Chute Top 4-56062143, Keeper Assembly, Drive Belt 4-32062145, Support Plate, Chute Side 4-56062149, Sleeve, .875” x 1.14” Lg Bushing 4-24, 4-48062149, Sleeve, .875” x 1.14” Long Bushing 4-12, 4-32,
4-580621571, Sleeve, 7/8” OD x 4.87” Long Bushing 4-12062999, O-Ring, Spindle 4-10, 4-38063202, Orifice, 1/4-28 x .040” ID x 3/8” 2-6063216, Spring, Wheel Yoke 1-0 Urethane 4-14, 4-64063236, Harness, 100EZT Electrical 2-2063265, Blade, 21” x 2 1/2” x 1/8” Low-Lift Ultra 4-4,
4-8, 4-28, 4-30, 4-34, 4-36063276, Spindle Assembly, Single Sheave w/Anti 4-36063277, Spindle Assembly, Double Sheave w/Anti 4-30063278, Spindle Assembly, Dbl Sheave Low w/ Anti
4-52063278, Spindle Assembly, Double Sheave Low w/Anti
4-8063280, Kit, 100EZT Installation Hardware 2-2063281, Spacer, Outer Wheel Bearing 2-6063282, Spacer, Inner Wheel Brg 2-6063327, Decal, 3682/96 Gearbox Fluid 1-4063356, Sure Grip, Seat Pan Right Side 2-10063735, Decal, Lastec Logo 1-4064182, Bracket Wedment, Toro Valve Mounting 2-8064190, Plate, Toro Footpan Adjust Lock 2-4064198, Stiffener Weldment, Blade E-Series 4-4, 4-8,
4-28, 4-30, 4-34, 4-36064234, Fitting, OFS x ORB 06-08 Str 2-8064235, Fitting, OFS x ORB 08-08 Str 2-8064236, Valve, Toro Deck Lift Bucher 2-8064558, Door Assembly, #2 Trap 4-26064560, Clamp Plate, #2 Deck Trap Door 4-26064564, Baffle Assembly, #2 Blowout 4-24064565, Baffle Weldment, #2 Blowout 4-24064568, Door Assembly #3 Deck Trap 4-32064569, Door, 521E/Z #3 Deck Trap 4-32064570, Clamp Plate, #3 Deck Trap Door 4-32064571, Door Assembly, #3 Deck Trap 4-32064572, Door, 521E/Z #3 Deck Trap 4-32064573, Clamp Plate, #3 Deck Trap Door 4-32064574, Door Assembly, #4 Deck Trap 4-50064575, Door, #4 Deck Trap 4-50064576, Clamp Plate, #4 Trap Door 4-50064577, Door Assembly, #4 Deck Trap 4-50064580, Baffle Assembly, #4 Blowout 4-50064581, Baffle Weldment, #4 Blowout 4-50064661, Door Assembly, #2 Trap 4-26064662, Door, #2 Deck Trap 4-26064663, Clamp Plate, #2 Deck Trap Door 4-26067043, Cover, 1 3/8”” Hole Plug 4-2, 4-26, 4-50, 4-52067076, Pin, 3/8” Dia Lynch Locking 4-64067092, Keeper, Main Drive Tensioner 3-2
iii Lastec//080216 Index
Part Number Index
067093, Keeper Weldment, Drive Belt (Bottom) 4-32067095, Keeper Weldment, Drive Belt (Top) 4-32067098, Plate, Idler Dampener Clamp 3-2067099, Plate Weldment, Idler Dapmener Clamp 3-2067135, Anti-Scalp Roller Assembly, 3300 4-22067136, Bracket Weldment, 3300 Anti-Scalp 4-22067142, Axle Rod, 3300 Anti-Scalp Roller 4-22067308, Hanger Weldment, 100EZT Rear Wheel 4-60067309, Chain, 5/16” x 6” Links 4-60067310, Hanger Assembly, 100EZT Rear Wheel 4-600673251, Chain, 5/16” x 5 Links 4-66067376, Door, #2/4 Deck Trap 4-26, 4-50067686, Spacer, Spindle Bearing Housing 4-6067687, Shaft, Blade Spindle ZT Cast 4-6067688, Sheave, Double - Mower Deck 4-4, 4-28067696, Spindle Assembly, Center w/Stiffener 4-6067696, Spindle Assembly, ZT Cast 4-4, 4-28, 4-34067776, Strap Assembly, Deck Support 4-58067999, Spindle Housing, ZT- Common Core 4-6072490, Plate Weldment, Toro Belt Guard 4-33072511, Spacer, Bearing Housing 4-6072623, Spindle Assembly, EZT 21" D6.3-6.3 Spacer
4-28072625, Spindle Assembly, EZT 21" D6.3 Spacer 4-34072626, Sheave, Single - D6.3 B1.00 Cast 4-34072628, Key, 1/4” Square x 1-1/4” Long 4-34072931, Service Yoke Assembly, Pivoting Wheel 4-64072934, Cylinder Assembly, #2 Deck Lift 4-66072935, Cylinder Assembly, #4 Deck Lift 4-66105249, Pulley Assembly, 5In OD Idler, V Groove Tall
4-20105249, Pulley Assy, 5In OD Idler, V Groove Tall 4-54FF04203-2, Rivet, 1/8” x 1/4” Al AA44D Pop 2-4F04254-12, Ring, 62mm IR Din #472 Retaining 3-2,
4-20, 4-32, 4-54F04254-45, O-Ring, 2 7/16" ID x 3/16" Diameter 4-10F04254-45, O-Ring, 2-7/16"ID x 3/16" Diameter 4-38F04254-46, Ring, 3/4” External - External 4-32F05004-176, Screw, M4- .7 x 50 Socket Head 2-2F05004-277, Bolt, M10-1.25 x 40mm Hex Head Grade
8.8 4-24, 4-48F05004-35, Screw, 10-24 x 1/2” SBHC 2-10F05004-95, Screw, 6-32 x 7/8 Round Head Phillips 4-66F05005-124, Bolt, 1/4-20 x 1 1/2” Hex Head Grade 5 2-4F05005-137, Bolt, 1/4-20 x 5/8” Hex Head Grade 5 4-32F05005-15, Bolt, 1/4-20 x 1/2” Hex Head 2-10F05005-18, Bolt, 1/4-20 x 2 3/4” Hex Head 2-4F05006-102, Bolt, 5/16-18 x 3/4” Hex Head 2-4, 4-50
F05006-102, Bolt, 5/16-18 x 3/4” Hex Head Grade 5 4-2, 4-26, 4-32, 4-50
F05006-140, Bolt, 5/16-18 x 5” Hex Head Grade 5 4-10F05006-140, Bolt, 5/16-18x5 HH Gr5 Zc 4-38F05006-141, Bolt, 5/16-18 x 1” BHCS SS 4-56F05006-15, Bolt, 5/16-18 x 1/2” Hex Head Grade 5 4-26,
4-50F05006-153, Bolt, 5/16-18 x 1-1/2 Carriage Grade 5 4-56F05006-27, Bolt, 5/16-18 x 1” Hex Head Grade 5 4-50,
4-66F05006-54, Bolt, 5/16-18 x 5/8” Hex Head Grade 5 2-8F05006-76, Bolt, 5/16-18 x 1 1/2” Hex Head Full Thread
Grade 5 4-20, 4-54F05006-86, Bolt, 5/16-18 x 3/4” Carriage 4-24, 4-50F05006-90, Bolt, 5/16-18 x 1” Carriage Grade 5 1-10,
4-56F05006-93, Bolt, 5/16-18 x 1 1/4” Hex Head Full Thread
Gr5 4-10F05006-93, Bolt, 5/16-18x1 1/4 HH FT Gr5 4-38F05007-118, Bolt, 3/8-16 x 3/4” Hex Head Grade 5 4-14F05007-119, Bolt, 3/8-16 x 1 3/4” Hex Head Grade 5
4-66F05007-123, Bolt, 3/8-16 x 1 1/4” Hex Head Grade 5 1-8F05007-124, Bolt, 3/8-16 x 2 HH Grd 8 YZD 4-46F05007-127, Bolt, 3/8-16 x 1 1/4” Carriage Grade 5 2-4F05007-131, Bolt, 3/8-16 x 1 1/4” Whiz Lock 4-42F05007-165, Bolt, 3/8-16 x 1” Carriage Grade 5 4-22F05007-165, Bolt, 3/8-16x1 Carriage 4-2, 4-26, 4-46,
4-50, 4-52F05007-201, Bolt, 3/8-16 x 2-1/4” Hex Head Grade 5 3-2F05007-210, Bolt, 3/8-16 x 3” Hex Head Grade 8 4-58F05007-244, Bolt, 3/8-16 x 4 1/2” Hex Head 316 SS 2-10F05007-73, Bolt, 3/8-16 x 3” Hex Head Grade 5 4-64F05007-78, Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5 4-4,
4-28, 4-32, 4-34, 4-60, 4-66F05007-85, Bolt, 3/8-16 x 1 1/2” Carriage Grade 5 4-8,
4-30, 4-36F05007-87, Bolt, 3/8-16 x 1” Hex Head Grade 5 3-4F05008-10, Bolt, 1/2-13 x 2 1/4” Hex Head Grade 5 4-20,
4-54F05008-116, Bolt, 1/2-13 x 2” Full Thread Grade 5 3-2F05008-134, Bolt, 1/2-13 x 3 1/4” Hex Head Grade 5
4-24, 4-48F05008-134, Bolt, 1/2-13 x 3” Hex Head Grade 5 4-32F05008-150, Bolt, 1/2-13x1 1/2 Carriage, Zinc 2-6F05008-155, Bolt, 1/2-13 x 9 1/2” Hex Head Grade 5 2-6F05008-171, Bolt, 1/2-20 x 6 1/2” Hex Head Grade 8
4-18F05008-23, Bolt, 1/2-13 x 3” Hex Head Grade 5 4-12,
Index Lastec//080216 iv
Part Number Index
4-64F05008-33, Bolt, 1/2-13 x 1 1/2” Hex Head Grade 5 4-24,
4-32, 4-40, 4-48F05008-37, Bolt, 1/2-13 x 1 1/4” Hex Head Grade 5 4-40F05008-50, Bolt, 1/2-13 x 1” Hex Head 2-6F05008-71, Bolt, 1/2-13 x 1” Hex Head Full Thread 4-22F05008-74, Bolt, 1/2-13 x 2 1/2” Hex Head Grade 5 3-2,
4-2, 4-24, 4-32, 4-48, 4-52F05008-88, Bolt, 1/2-13 x 1 3/4” Hex Head Grade 5 4-42,
4-58F05008-96, Bolt, 5/16-18 x 1 1/2” Hex Head 2-2F05009-104, Bolt, 3/4” ID x 6” Carriage Grade 5 4-14F05009-104, Bolt, 3/4-10 x 6” Carriage Grade 5 4-58,
4-64F05009-116, Bolt, 5/8-11 x 2” Carriage Grade 5 4-40,
4-58F05009-123, Bolt, 5/8-11 x 2 1/2” Grade 5 Carriage 4-12F05009-125, Bolt, 5/8-11 x 4 1/2” Hex Head Grade 8
4-66F05009-20, Bolt, 5/8-11 x 2 1/2” Hex Head Grade 5 4-2,
4-24, 4-48, 4-52F05009-35, Bolt, 5/8-11 x 2 3/4” Hex Head Grade 5 4-24,
4-48F05009-39, Bolt, 5/8-11 x 6 1/2” Hex Head Grade 5 4-12F05009-41, Bolt, 5/8-11 x 1 1/2” Hex Head Full Thread
Grade 5 4-24, 4-48F05009-54, Bolt, 3/4-10 x 3 1/2” Hex Head Grade 5 2-4F05009-95, Bolt, 5/8-18 x 1 3/4” Hex Head Grade 5 4-4,
4-8, 4-28, 4-30, 4-34, 4-36F05010-10, Nut, 3/8-16 Hex Nyl Lock 4-46F05010-10, Nut, 3/8-16 Hex Nyloc 1-8, 4-8, 4-22, 4-30,
4-32, 4-36, 4-60, 4-64F05010-10, Nut, 3/8-16 Hex Nylock 4-2, 4-66F05010-103, Nut, 3/4-10 Nylock 2-4F05010-118, Nut, 1-14 Hex Jam 4-66F05010-121, Nut, 5/16-18 Nylon Locking Jam 1-10, 4-2,
4-24, 4-26, 4-50, 4-52F05010-122, Nut, 3/4-10 Half Nylon Lock 4-54F05010-124, Nut, 3/8-16 Half Nyloc 2-4, 3-2, 4-58F05010-127, Nut, 1/2-13 Half Nyloc 2-6, 3-2, 4-24,
4-32, 4-48F05010-127, Nut, 1/2-13 Half Nylon Lock 4-20, 4-54,
4-58F05010-14, Nut, #10-24 Keps 2-10F05010-15, Nut, 1/2-20 Nyl Hex Lock 4-62F05010-156, Nut, 1/4-20 Half Nylock 2-4F05010-156, Nut, 1/4-20 Half Nylon Lock 2-10F05010-16, Nut, 1/2-20 Hex Jam 4-44, 4-62F05010-16, Nut, 1/2-20 Hex Jam 4-18
F05010-162, Nut, M8 x 1.25 Free Zinc Plate 2-8F05010-167, Nut, M4- .7 Prev Torq 2-2F05010-17, Nut, 5/16-18 Hex 4-16, 4-20, 4-24, 4-48,
4-54F05010-177, Nut, 3/4-10 Stover Lock 4-14F05010-177, Nut, 3/4-10 Stover Swaged 4-58, 4-64F05010-178, Nut, 3/4-10 Flexloc 4-12F05010-185, Nut, 5/8-11 FlexLoc 4-2, 4-12, 4-24, 4-40,
4-48, 4-52, 4-58F05010-192, Nut, M10-1.25 Free Zinc Plate 3-2, 4-2,
4-24, 4-48, 4-52F05010-221, Nut, 5/16-18 Flanged Hex Nylock 4-20,
4-54, 4-56F05010-222, Nut, 3/8-16 Flanged Hex Nyloc 4-4, 4-28,
4-34F05010-222, Nut, 3/8-16 Flanged Hex Nylock 4-2, 4-26,
4-46, 4-50, 4-52F05010-225, Nut, 3/4-10 Flanged Hex Nylock 4-20F05010-234, Nut, 3/8-16 Hex Half Nylon Lock 316 SS
2-10F05010-35, Nut, 1/2-13 Hex 3-2F05010-58, Nut, 5/16-18 Nylok Hex 4-38, 4-52F05010-58, Nut, 5/16-18 Nylon Lock 2-2F05010-58, Nut, 5/16-18 Nylon Lock Hex 4-10F05010-59, Nut, #6-32 Keps 4-66F05010-69, Nut, 1/4-20 Nylock 2-4F05010-79, Nut, 1/2-20 Jam Nyl Lock 4-18, 4-40, 4-42F05010-79, Nut, 1/2-20 Jam Nylon Lock 4-44F05010-79, Nut, 1/2-20 Jam Nylon Lock 4-58F05010-8, Nut, 1/2-13 Nyl Hex Lock 3-2, 4-2, 4-12,
4-24, 4-48, 4-52F05010-8, Nut, 1/2-13 Nylon Hex Lock 2-6, 4-64F05010-96, Nut, 5/8-11 Jam Nyl Lock 4-24, 4-48, 4-66F05011-104, Washer, 3/8 x 1 1/2” x 1/8” 4-14F05011-11, Washer, 1/4” SAE Flat 2-4F05011-115, Washer, 1” ID .03 SS Shim 4-14, 4-64F05011-116, Washer, 1” ID .06 SS Shim 4-14, 4-64F05011-13, Washer, 5/16 Split Lock 4-38F05011-13, Washer, 5/16” Split Lock 4-32F05011-13, Washer, 5/16” Split Lock 2-4, 2-8, 4-10,
4-16, 4-24, 4-26, 4-32, 4-48, 4-50, 4-66
F05011-14, Washer, 1/4” Split Lock 4-32F05011-17, Washer, 5/16” SAE Flat 1-10, 2-4, 4-26,
4-50, 4-52F05011-2, Washer, 1/2 SAE Flat 3-2F05011-2, Washer, 1/2” SAE Flat 4-44, 4-62F05011-2, Washer, 1/2” SAE Flat 4-18, 4-32, 4-40,
4-64
v Lastec//080216 Index
Part Number Index
F05011-27, Washer, 5/8 Split Lock 4-4, 4-28F05011-27, Washer, 5/8” Split Lock 4-8, 4-30, 4-36F05011-3, Washer, 3/8 Flat SAE 4-46F05011-3, Washer, 3/8” Flat SAE 1-8, 4-22, 4-64F05011-3, Washer, 3/8” SAE Flat 4-58F05011-3, Washer, 5/16” Split Lock 4-2F05011-4, Washer, 3/8” Split Lock 3-4, 4-14F05011-40, Washer, 5/8” Standard Flat 4-24, 4-48F05011-5, Washer, 5/8” SAE Flat 4-12, 4-24, 4-48,
4-66F05011-50, Washer, 5/16” x 1 1/4” Fender 4-26, 4-50,
4-56F05011-6, Washer, 3/4 Split Lock 2-6F05011-62, Washer, 3/4” SAE Flat 2-4, 4-14, 4-64F05011-68, Washer, 1/2 Standard Flat 4-54F05011-68, Washer, 1/2” Standard Flat 4-20F05011-77, Washer, 3/4” AN Yel/Cad 4-20, 4-54F05011-89, Washer, 2 1/2” OD x 5/8” ID x 3/16” Std Flat
Znc 4-34F05011-9, Washer, 1/2 Split Lock 3-2F05011-9, Washer, 1/2” Split Lock 2-6, 4-22, 4-24,
4-32, 4-48F05011-97, Washer, 1/2” Plain Belleville 4-4, 4-8, 4-28,
4-30, 4-34, 4-36F05012-64, Pin, 1/8” x 1/2” Roll 4-10F05012-64, Pin, 1/8x1/2 Roll 4-38F05013-72, Bolt, 3/4-16x1 1/2 HH Gr5 2-6F05015-36, Screw, #10 x 1/2 Long AB Thrd Slot Hex
Head 4-26F05015-36, Screw, #10 x 1/2” Long AB Thrd Slot Hex
Head 4-50F05015-7, Bolt, #10-24 1/2” Self Tap 2-2F05089-3, Tie Wrap, 3/16” x 5 1/2” UV Black 2-2F05089-5, Wire Tie, 14” Black 2-2F81003-25, Bolt, M10-1.25 x 30mm Hex Head FT 8.8
4-52F81003-25, Bolt, M10-1.25x30mm HHFT 8.8 4-2F81033-6, Nut, 10mm x 1.25 Nylon 3-2, 4-2, 4-24,
4-48, 4-52IIS-0387, Instruction Sheet, 1-12 Spindle 4-10
PP04101-1, Key, #606 Woodruff 3-4P06104, Foot, Rubber 2-10P103, Bearing, Spindle Top 6305 RS 3-2, 4-20, 4-32,
4-54P105, O-Ring, 2 1/2” ID x 2 3/4” OD 4-6P107, Fitting, 1/4-28 Straight Grease 2-4, 4-4, 4-8, 4-12,
4-28, 4-30, 4-34, 4-36, 4-42, 4-58, 4-64, 4-66
P109, Bushing, 1” ID x 1 1/4” OD x 1 1/4” Flanged 4-14, 4-42
P109, Bushing, 1” ID x 1-1/4” OD x 1-1/4” Flanged 2-6, 4-64
P11035, Bearing, 6206-2NSE 2-6, 4-6, 4-10, 4-38P116, Washer, 1-1/16” x 1-3/4” x 1/8” 4-64P117-toro, Decal, Hands and Feet - Toro 1-4P123, Fitting, Grease 90 Deg. 1/4-28 2-6, 4-20, 4-54P128, Blade, 21” x 2 1/2” x 1/4” High Lift 4-4, 4-8, 4-28,
4-30, 4-34, 4-36P246, Blade, 21” Low-Lift 4-4, 4-8, 4-28, 4-30, 4-34,
4-36P292, Bearing, Tapered Roller 3/4” ID 2-6, 4-16P293, Seal, 1 1/8” ID Trb Bearing 2-6, 4-16P294, Fitting, 1/4-28 45 Deg Grease 3-2P294, Fitting, 1/4-28 45 Deg. Grease 2-6, 4-16P296, Spacer, 1.13” OD x .75” ID x .5” 4-12, 4-58P322, Blade, 21” Gator Mulching 4-4, 4-8, 4-28, 4-30,
4-34, 4-36P402, Bearing Race Insert, 3/4” TRB 4-16P402, Bearing Race Insert, 3/4” Trb 2-6P410, Spring, 1” x 7” Extension 4-20, 4-54P438, Wheel, Anti-Scalp 6” x 3.25” x 3/4” ID 4-22, 4-40P438, Wheel, Anti-Scalp 6” x 3.25” x 3/4”ID 4-60SS04124, Key, 1/4” x 1 11/16” 4-36S04827, Handle, Outrigger Jack 2-10TT104, Spacer, 1 3/4” OD x 1 1/64” ID x 1/4” 4-14T104, Spacer, 1” ID x 1-3/4” OD x 1/4” 4-64T107, Spacer, 1 3/4” OD x 1 1/16” ID x 1” 4-64T125, Spacer, Dual Wheel Outer Bearing 4-12
Index Lastec//080216 vi