Disclosure to Promote the Right To Information
Whereas the Parliament of India has set out to provide a practical regime of right to information for citizens to secure access to information under the control of public authorities, in order to promote transparency and accountability in the working of every public authority, and whereas the attached publication of the Bureau of Indian Standards is of particular interest to the public, particularly disadvantaged communities and those engaged in the pursuit of education and knowledge, the attached public safety standard is made available to promote the timely dissemination of this information in an accurate manner to the public.
इंटरनेट मानक
“!ान $ एक न' भारत का +नम-ण”Satyanarayan Gangaram Pitroda
“Invent a New India Using Knowledge”
“प0रा1 को छोड न' 5 तरफ”Jawaharlal Nehru
“Step Out From the Old to the New”
“जान1 का अ+धकार, जी1 का अ+धकार”Mazdoor Kisan Shakti Sangathan
“The Right to Information, The Right to Live”
“!ान एक ऐसा खजाना > जो कभी च0राया नहB जा सकता है”Bhartṛhari—Nītiśatakam
“Knowledge is such a treasure which cannot be stolen”
“Invent a New India Using Knowledge”
है”ह”ह
IS 3413 (2004): Base paper for carbon paper [CHD 15: Paperand its products]
IS 3413:2004
Wi’i9hmc \
lwwi’(- muTNT?TFmT-faFm
( m 3T?m )
Indian Standard
BASE PAPER FOR CARBON PAPER—SPECIFICATION
(Second Revision )-.
ICS 85.080
C) BIS 2004 /
BUREAU OF INDIAN STANDARDSMANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG
NEW DELHI 110002
November 2004 Price Group 3
Paper and Its Products Sectional Committee, CHD 15
FOREWORD
This Indian Standard (Second Revision) was adopted by the Bureau of Indian Standards, after the draft finalizedby the Paper and Its Products Sectional Committee had been approved by the Chemical Division Council.
This standard was first published in 1966 and subsequently revised in 1977 by modifying grammages of variousgrades of paper to suit the requirements of the users and to economize on the cellulose raw materials. Dependingon the users preferences during that time Grade 1 was introduced under Type 2, Grade 2 of Type 3 was re]moved,and the requirement of porosity was included to take care of excessive pin holes in the base paper.
‘file quality of the base paper prescribed for making the following types of carbon papers is laid down in thisstandard:
IS No. Title
1551:1991 Carbon papers for typewriter (second revision)
3450: 1994 Carbon papers, handwriting (seco/zd revision)
8075:1976 Back coated carbon papers for typewriter
A scheme for label Iing environment friendly products known as ECO-Mark has been introduced at the instance ofthe Ministry of Environment and Forest (MEF), Governrnent of India. The ECO-Mark scheme would beadrninistered by the Bureau of Indian Standards (B IS) under the BISAct, 1986 as per the Resolutions No. 71 dated2 I February 199 I and No. 425 dated 28 October 1992 published in the Gazette of the Government of India. Fora product to be eligible for marking with ECO logo, it shall also carry the 1S1Mark of BIS besides meetingadditional environment friendly requirements. For this purpose, the Standard Mark of BIS would be a single markbeing a combination of the 1S1 Mark and the ECO logo. Requirements to be satisfied for a product to qualify forthe BIS Standard Mark for ECO friendliness, will be optional; manufacturing units shall be free to opt for the1S1 Mark alone also.
This standard, therefore, incorporates environment friendly requirements for cover paper which is based on theGazette Notification No. 455 dated 13 November 1992 for paper as environment friendly products published inthe Gazette of India.
This standard contains clauses 4.4 and 5.1 which permit the purchaser to use his option for selection to suit hisrequirements.
The composition of the Committee responsible for the formulation of this standard is given in Annex B.
For the purpose of deciding whether a particular requirement of this standard is complied with, the final value,observed or calculated, expressing the result of a test or analysis shall be rounded off in accordance withIS 2: 1960 ‘Rules for rounding off numerical values (revise@’. The number of significant places retained in therounded off value should be the same as that of the specified value in this standard.
1S 3413:2004
Indian Standard
BASE PAPER FOR CARBON PAPER—SPECIFICATION
(Second Revision)
1 SCOPE
This standard prescribes the requirements and themethods of sampling and test for base paper for carbonpaper. This standard, however, does not cover the basepaper used for making one-time carbon paper.
2 REFERENCES
The following standards listed below containprovisions, which through reference in this text,constitute provisions of this standard. At the time ofpublication, the editions indicated were valid. Allstandards are subject to revision, and parties toagreements based on this standard are encouraged toinvestigate the possibility of applying. The most recenteditions of the standards indicated below :
[S No. Title
1060 (Part l): Methods of sampling and test for\ 966 paper and allied products : Part 1
(revised)
1260 (Part 2) : Packaging — Pictorial marking for1999 handling and Iabelling of goods:
Part 2 General goods (thirdrevision)
3 TYPES AND GRADES
3.1 Types
There shall be three types of base paper for carbonpaper based on requirements for tensile index andburst index as given in Table 1.
3.2 Grades
Type 1 and Type 2 each shall be of five grades, andType 3 of three grades, from Grade 3 to Grade 5, asg,jven be]~w:
Grade 1 – Light weight
Grade 2 – Medium weight
Grade 3 – Standard weight
Grade 4 – Heavy weight
Grade 5 – Extra heavy weight
4 REQUIREMENTS
4.1 General Requirements
The paper shall be of good formation. It shall have closetexture, smooth and even surface, and fairly good
opacity. It shall be free from slack and tight edgesand, as far as possible, from pin-holes, thin spots,cockles and creases.
4.2 The base paper shall be supplied in evenly woundrolls with the wire side of the paper inside. The numberof joints in a reel on an average shall not exceed twojoints per 2000 m length. This average shall becalculated on 20 reels selected at random. Splicesshould be marked.
4.3 The base paper shall also comply with therequirements given in Table 1 when tested accordingto the test methods specified in CO1 16 and 17 ofTable 1.
4.3.1 Tolerance on Grammage
For Grades 1, 2 and 3 a tolerance of* 1.0 g/m2, andfor Grades 4 and 5 a tolerance of + 1.5 g/m2 shall beallowed for individual test results on the nominalgrammage specified in Table 1.
4.4 Width
The width of roll shall be as agreed to between thepurchaser and the supplier. The tolerance on nominalwidth shall be as follows:
S1 No. Nominal Width Tolerancemm mm
(1) (2) (3)
i) up to 150 * 1.5
ii) Above 150 * 2.0
5 ADDITIONAL REQUIREMENTS FORECO-MARK
5.1 General Requirements
5.1.1 The product shall conform to the requirementsfor quality and performance prescribed 4.1 to 4.4.
5.1.2 The manufacturers shall produce to BIS,environmental consent clearance from the concernedState Pollution Control Board as per the provisions ofWater (Prevention and Control of Pollution) Act, 1974and Air (Prevention and Control of Pollution) Act,1981 alongwith the authorization, if required underthe Environment (Protection) Act, 1986 while applyingfor ECO-Mark.
IS 3413:2004
6 PACKING AND MARKING
6.1 Packing
The paper roll shall be securely packed with suitablewater-proof packing as agreed by the purchaser andthe supplier.
6.1.1 For ECO-Mark, the product shall be packed insuch packages which shall be recyclable/reusable orbiodegradable.
6.2 Marking
6.2.1 Each package shall be marked with the followinginformation :
a)
b)
c)
d)
e)
f)
g)
Description of the material including type anddgra e;
Grammage of paper;
Mass of package;
Batch and lot number;
Month and year of manufacture;
Name of the manufacturer and trade-mark, ifarty; and
For consignments to be transshipped, thepictorial marking ‘Use no hooks’ as containedin IS 1260 (Part 2) shall be stenciled or indeliblymarked on the rolls.
6.2.2 For ECO-Mark, following additional informationmay also be marked on the container/package:
The criteria for which theIabelled with ECO-Mark.
6.2.3 BIS Cet-tl~cation Marking
The product may also be markedMark.
product has been
with the Standard
6.2.3.1 The use of the Standard Mark is governed bythe provisions of Bureau of Indian Standards Act,1986 and the Rules and Regulations made thereunder.The details of conditions under which the licencefor the use of the Standard Mark may be granted tomanufacturers or producers may be obtained fromthe Bureau of Indian Standards.
7 SAMPLING
7.1 Representative sample for tests shall be drawn asprescribed in 3 of IS 1060 (Part 1).
7.2 Number of Tests
Each of the selected packages shall first be testedfor the requirements given in 4.2. Then from each ofthese packages number of sheets sufficient to carryout all the tests specified in Table I shall be taken outat random. These sheets shall constitute the sample.These sheets shall first be examined for therequirements given in 4.1 and 4.4 and then number oftest pieces for each of the characteristics as indicatedin its test method shall be cut from them. These piecesshall be tested according to the methods specified inCO116 and 17 of Table 1.
7.3 Criteria for Conformity
7.3.1 A sheet not meeting the relevant requirements “for any one or more characteristics shall be consideredas defective.
7.3,2 A lot shall be declared as conforming to therequirements of this standard, if the number ofdefective sheets found does not exceed the acceptancenumber. This acceptance number shall depend uponthe size of the sample and shall be equal to O, if thesize is less than 13 and 1 if the size is greater than orequal to 13.
Table 1 Requirements for Base Paper for Carbon Paper
(Clauses 3.1,4 .3,4.3.1 and 7.2)
S1 No. Characteristic Requirements Method of Test,Ref to
/Type 1 Type 2 Type 3
\!lnnex of Clause o~
~ ~ ~ s:::.d :ZGr 1 Gr 2 Gr 3 Gr 4 Gr 5 Gr 1 Gr 2 Gr 3 Gr 4 Gr 5 Gr 3 Gr 4 Gr 5
(1) (2) (3) (4) (5) (6) (7) (8) (9) (lo) (11) (12) (13) (14) (15) (16) (17)
i) Nominal grammage, g/m2 11.5 14.5 17.5 20.5 27.0 11.5 15.5 17.5 20.5 27.0 17.5 20.5 27.0 - 6
ii) Ash content, percent by mass, Max 5 5 5 5 5 5 5 5 5 5 5 5 5- 11
}MD 65 65 65 65 65 55 55
iii) Tensile index, Nrn/g, Min55 55 55 45 45 45 - 12.3
CD 27 27 27 27 27 25 25 25 25 25 20 20 20 - 12.4
iv) Burst index, kPa.m2/g,A4in 2.94 2.94 2.94 2.94 2.94 2.45 2.45 2.45 2.45 2.45 1.96 1.96 1.96 - 12.5
v) Porosity, s/100 ml, &fin 400 400 400 270 270 400 400 400 270 270 400 270 270 A —
.. u
..
1S 3413:2004
ANNEX A
[Table 1, S1 No, (v)]
METHOD FOR DETERMINATION OF POROSITY
A-1 APPARATUS
A-l. ] Air Resistance Apparatus
The apparatus consists of an outer cylinder which ispartly filled with oil, and an inner cylinder, having anopen or closed top, sliding freely in the outer cylinder.Air pressure provided by the mass of the inner cylinderis applied to the specimen held between clampingplates in a circular orifice having an area of 6.4 cm2.The clamping plates may be at the top of the innercylinder, or may preferably be mounted on the base ofthe apparatus. An elastic gasket which is attached tothe clamping plate on the side exposed to air pressureprevents leakage of air between the surface of the paperand the clamping plate.
A-1.1.1 The gasket consists of a thin, elastic oilresistant, non-oxidizing material having a smoothsurface (see Note). The inside diameter of thegasket is 28.6 + O.1 mm and the outside diameter34.9 + 0.1 mm. The aperture in the gasket is accuratelyaligned with the aperture in the clamping plates. Toalign and protect the gasket in use, it is cemented in agroove machined in the clamping plate. The groove isconcentric with the aperture in the opposing plate. Itis 28.41 + 0.04 mm in internal diameter and0.45 + 0.05 mm deep. Its outside diameter is35.14 & 0.04 mm for convenience in inserting andattaching the gasket.
NOTE — Thiokol, grade ST, polished plate moulded,0.8 mm thick, 50 to 60 IRHD is satisfactory.
A-1.1.2 The outer cylinder is 25.4 cm high with aninternal diameter of 82.6 mm. It has four vertical bars,each 245.5 mm long, and 2.4 mm in diameter, mountedequidistantly on the inner surface of the outer cylinderto serve as guides for the inner cylinder. The innercylinder is made of aluminium or its alloy, graduatedin units of 50 ml, and has range of 350 ml. The volumetolerance is 0.5 percent. It is 25.4 cm high, and has anexternal diameter of 76.2 mm and an internal diameterof 74.1 mm. It weighs 567.0 + 0.5 g, so as to producea pressure of 12.4 cm H20.
NOTE — Some inner cylinders are also graduated in units of25 ml for the first 100ml and have an additional graduation at400 ml.
A-1.2 Timer
Stopwatch or electric timer, capable of recording timeto the nearest 0.2 s.
A-2 MATERIALS
The outer cylinder is filled with a lubricating oil having
4
a viscosity of 10 to 13 cSt at 37.8°C and a flash point.. a-,.-
Of “at least 13>UC.
NOTE — A light spindle oil is suitable for this purpose. Oil isused in preference to water because it does not affect themoisture content of the specimen nor does it corrode theahrminiuminnercylinder. The oil should not contain any easilyvolatile fraction, and for that reason, a minimum flash point isspecified.
A-3 CALIBRATION
Test the apparatus for air leakage by clamping a thinpiece of smooth impervious metal foil or cellulose filmbetween the orifice plates, using the method prescribedin A-5.2 to A-5.5. A maximum leakage of 50 ml in5 h is allowable.
A-4 TEST SPECIMENS
From each test unit of the sample prepare at least tentest specimens, each about 5 cm wide and 12.5 cmlong except that the specimens of size larger than 5cm in both directions may be used in the apparatushaving the clamp on the base.
A-5 PROCEDURE
A-5.1 Condition the test specimens in an atmospherehaving 27+ 2°C temperature and a relative humidityof 65 + 5 percent.
A-5.2 Place the instrument on a level surface so thatthe cylinders are vertical. Fill the outer cylinder withoil to a depth of about 12.5 cm as indicated by a ringmarked on the inner surface of the cylinder.
A-5.3 For the instrument having the clamp at the topof the inner cylinder, raise the inner cylinder with onehand and clamp the specimen with the other. Thenlower the inner cylinder and allow it to float in the oil.Alternatively, remove the inner cylinder, clamp thespecimen and lower the cylinder gently in the outercylinder.
NOTE — The proper procedure is to tighten the knurlednuts alternately so that the clamping pressure is equal onboth sides. Ifonly one nut at a time is tightened, the clamp willnot bear evenly on the specimen and air leakage will probablyoccur.
A-5.4 For the instrument having the clamp on thebase, raise the inner cylinder until its rim is supportedby the catch, clamp the specimen between theclamping plates and then lower the inner cylindergently until it floats.
A-5.5 As the inner cylinder moves steadily downwards,determine the number of seconds, to the nearest 0.2 s,required for the first two consecutive 50-ml intervals
IS 3413:2004
to pass the rim of the outer cylinder, starting at the and five specimens with the wire side up.zero point. In cases where a steady movement of theinner cylinder is not attained before the zero mark is A-6 REPORT
reached, timing may be started at the 50 ml mark.For each test unit, report the porosity as the average
NOTE — Avoid subjecting the apparatus to vibration, as this time, in seconds required to displace 100 ml of airincreases the rate ot’air displacement.
thrcrugh an area of 6.45 cm2 of the paper. Report to the
A-5.6 Test five specimens with the top or felt side up nearest second.
IS 3413:2004
ANNEX B
(Foreword)
COMMITTEE COMPOSITION
Paper and Its Products Sectional Committee, CHD 15
Organization
Seshasayee Paper& Boards Ltd, ErodeAll India Federation of Master Printers, New Delhi
B & A Multiwall Packaging Ltd, Kolkatat3allarpur Industries Ltd, New DelhiCard Iloard Box Manufacturing Company, KolkataCentral Forensic Science Laboratory, New DelhiCentury Pulp and Paper Mills, NainitalCentral Pulp & Paper Research Institute, Saharanpur
Central Revenues Control Laboratory, New DelhiEkfcmceMaterials & Stores R & D Establishment, Kanpur
Department of Industrial Policy & Promotion, New Delhi
Directorate General of Supplies& Disposals, New DelhiDirectorate of Printing (Ministry of Urban Development),
New DelhiFederation of Corrugated Box Mfrs’ ofhsdia, Mumbai
Federation of Paper Traders Association of India, Mumbai
Forest Research Institute, Debra DunHindustan Lever Research Centre, Mumbai
I{industan Paper Corporation Ltd, Kolkata
India Foils Ltd, KolkataIndia Security Press, NasikIndian Agro and Recylced Paper Mills Association, New Delhilnclian Paper Manufacturers Association, New Delhi
lndian Pulp and Paper Technical Association, SaharanpurIndian Institute of Packaging, Mumbai
Indian Institute of Technology, Saharanpur
Indian Newsprint Manufacturers Association, New DelhiIndian Recycled Paper Mills Association, DelhiITC Bhadrachalam Paper Board Ltd, SecunderabadJK Paper Ltd, New DelhiMinistry of Defence (DGQA), New Delhi
National Alliance of Young Entrepreneurs, New DelhiNEPA Limited, Nepaoagar
Pesticides Association of India, New DelhiRegional Research Laboratory (CSIR), Jorhat
Secority Printing Press, Hyderabad
Stationery Otlice, Government of India, KolkataThe Mysore Paper Mills Ltd, ShimogaThe Sirpor Paper Mills Ltd, Kaghazmagar111SDirectorate General
Representative(s)
SW N. GOPALARATNAM(Chairman)Smu S. R. SHARMA
Sma V. K. MALtK (,4/(errrafe)
Smu RONODURIOYROY CHOUDHURY
DR S. C. SHENOY
Smu A. B. AmssuSmu S. L. MmSmu D. P. CHANDARANA
DR S. K. KAPOOR
DRY. V. SDOD(Mfernate)
REpRE5EmAmE
Smr S. P. BAtPAISmu V. K. SCNGH(Alternate)
Strru P. K. JAIN
DR K. R. Murutrv (Alternate)
RSPRESENTATWS
SsmaJocmwsrt SINGH
Smu PANKAJD. SW
Smr M. L. MEHRA(Alternate)
Smu SATVAPAL GUPTA
Ssira BADALCHADDHUM(,41/errra/e)
DR K. S. BHANDARI
Sr+roM. V. PRASHAKARAN
Smu M. K. L.muu (Alternate)sHru Rut PHrLrP
Smo J. D. FERNANDES(Mernate)
REpiIE.5EmAnW
REPRESENTATIVE
Smu S. K. SHARMA
Wro C. T. DATHATHREYA
Sma R. VARDHAN(Alternate)DR ASHOKKUMAR
Swo Rmv DHAR
SHRIK. B. GUFTA (Alternate)
DR J. S. UPADHVAYA
DR A, K. IQY (Alternate)SHRIB, P. UTAPPA
SHRIR. C. RASTOGI
SHRIASHISHDE
Stuu S. C. MAJUMDAR
.%ru K. N. PATtL
SHRtP. H. KULKARNt(Alternate)REPRESENTATtVE
SW K.AMALSww
Smu NmzI R. A. KHAN(Alternate)SHRIARUNKAPOOR
StrrrrS. K. GHOSH
DR FASUDh (Afernate)SHro P. N. RADKAR
SHRIS. G. K. ACHARYULU(Alternate)SHRIR. K. ROY
%0 K. RAW
REPRESENTAIWE
DR U. C. SRIVASTAVA,Director & Head (CHD)
.-
[Representing Director General (Ex-oficio)]
Member Secretary
SHRIS. N. CHATTERJEE
Director (CHD), 91S
6
Bureau of Indian Standards
BIS is a statutory institution established under the Bureau of Indian Standards Act, 1986 to promoteharmonious development of the activities of standardization, marking and quality certification of goods andattending to connected matters in the country.
Copyright
BIS has the copyright of all its publications. No part of these publications may be reproduced in any formwithout the prior permission in writing of BIS. This does not preclude the free use, in the course of implementingthe standard, of necessary details, such as symbols and sizes, type or grade designations. Enquiries relating tocopyright be addressed to the Director (Publications), BIS.
Review of Indian Standards
Amendments are issued to standards as the need arises on the basis of comments. Standards are also reviewedperiodically; a standard along with amendments is reaffirmed when such review indicates that no changes areneeded; if the review indicates that changes are needed, it is taken up for revision. Users of Indian Standardsshould ascertain that they are in possession of the latest amendments or edition by referring to the latest issue of‘BIS Catalogue’ and ‘Standards: Monthly Additions’.
This Indian Standard has been developed from Doc: No. CHD 15 (996).
Amendments Issued Since Publication
Amend No. Date of Issue Text Affected
BUREAU OF INDIAN STANDARDS
Headquarters:
Manak Bhavan, 9 Bahadur Shah Zafar Marg, New Delhi 110002Telephones: 23230131,23233375,2323 9402 website: www.bis.org.in
Regional Offices: Telephones
Central :
Eastern :
Northern :
Southern :
Western :
Branches :
Manak Bhavan, 9 Bahadur Shah Zafar Marg{
23237617NEW DELHI 110002 23233841
1/14 C.I.T. Scheme VII M, V.I.P. Road, Kankurgachi{
23378499,23378561KOLKATA 700054 23378626,23379120
SCO 335-336, Sector 34-A, CHANDIGARH 160022{
26038432609285
C.I.T. Campus, IV Cross Road, CHENNAI 600113{
22541216,2254144222542519,22542315
Manakalaya, E9 MIDC, Marol, Andheri (East){
28329295,28327858MUMBAI 400093 28327891,28327892
AHMEDABAD. BANGALORE. BHOPAL. BHUBANESHWAR. COIMBATORE. FARIDABAD.GHAZIABAD. GUWAHATI. HYDERABAD. JAIPUR. KANPUR. LUCKNOW. NAGPUR.NALAGARH. PATNA. PUNE. RAJKOT. THIRUVANANTHAPURAM. VISAKHAPATNAM.
“Printedat SlmcoPrintingPress,Delhi