SERIA LC și SLU
800W – 2400W
Display Fața Spate Aparatele din gama LC încorporează un invertor sinusoidal pur și un încărcător DC de baterie, iar cele din SLU încorporează pe lângă acestea și un încărcător solar suplimentar.
Cum funcționează acest aparat back up? Aparatul se conectează la INPUT la o priză, iar la OUTPUT se leagă la o baterie (de preferat cu ciclu profund). Atâta timp, cât rețeaua electrică furnizează curent electric, aparatul preia acest curent și îl transmite mai departe la consumator, iar încărcătorul de baterie menține încărcarea bateriei (sau încarcă pe acesta, dacă este descărcată). Modelele SLU prin încărcătorul solar încorporat completează încărcarea bateriei și de la panourile fotovoltaice. Încărcătorul solar funcționează independent de redresorul DC, deci chiar dacă aparatul nu este conectat la reteaua electrică, bateria este incărcată de la panourile fotovoltaice. Când se întrerupe curentul, aparatul trece automat la modul de baterie (inverter mode), asigurând curent electric fără intrerupere aparatelor electrice. Când invertorul sesizează, că se reia furnizarea curentului electric în rețea, automat se deconectează de la baterie, și va furniza curent electric de la priză, încărcând bateria. Mețiune: bateria nu este încorporata în acest aparat, ea se alege in funcție de necesitatea energetică a consumatorilor. Acestea nu sunt dispozitive UPS propriu zise! Caractreristici generale pentru toate modelele:
LCD display Solar charge controller (SLU) Multistage charger Fast Action AC Synchronized Transfer Switch Microprocessor based design Heat-Sink built in internal Soft Start AVR design Input & Output isolated Auto temperature control fan Reverse polarity protection. / by fuse / diodes / Output short circuit protection Temperature protection Overload protection Input low voltage protection Input high voltage protection Low battery alarm Low battery shut-dow
Descriere:
Solar Inverter with LCD Display PURE SINE WAVE Inverter with DC battery charger and Solar charge controller Connect directly with Solar system Smart, powerful and successful
Specificații tehnice pentru modelele 800W, 1600W, 2400W: Model No. PM-0800LC PM-0800LC-24
Output Power Continuous 800W
Max. Surge Power 1600W
1. Input Section
Input Nominal Voltage 110Vac or 220Vac
Input Voltage Range 60V~140Vac or 120V~280Vac
Line Low Transfer 60Vac ± 2% or 120Vac ± 2%
Line Low Return 65Vac ± 2% or 130Vac ± 2%
Line High Transfer 140Vac ± 2% or 280Vac ± 2%
Line High Return 130Vac ± 2% or 260Vac ± 2%
Input Frequency 50Hz / 60Hz (45Hz~70Hz)
2. Output Section
Output Voltage 100 / 110 / 115 / 120Vac or 200 / 220 / 230 / 240Vac
re-settable via LCD panel
Waveform Pure Sine Wave
Voltage Regulation (Batt. Mode) < 3% RMS for entire battery voltage range
Output Frequency 50Hz or 60Hz ± 0.1Hz
Efficiency > 75%
Maximum Load Up to short circuit
Asymmetrical Load Max. Up to nominal output power
Overload and Short Circuit Protection Automatic disconnection
Overheating Temperature Protection Acoustic warning before shut-off.
Automatic restart
Power Factor 0.8
3. Battery Section
Voltage Range 12VDC (10~16VDC) 24VDC (20~32VDC)
Backup Time (at full load) Long time available
Input Frequency Range 45~70Hz
Max. Charging Current (5 steps selectable)
> 40Amp 60/80/100Amp
4. Display
LCD Display UPS status, I/P&O/P Voltage Frequency, Load%,
Battery Voltage & %, Temperature, Model
LED Display Normal (Green), Warning (Yellow), Fault (Red)
5. Audible Alarm
Battery Mode Beeping every 4 seconds
Low Battery Beeping every second
Overload Beeping twice per second
Temperature Compensation (Option) 3mV / °C cell
6. General date
AC By Pass Time (UPS Mode) < 8 ms.
Operation Temperature -20 °C to +55 °C
Audible Noise Less than 55dBA (at 1M)
Relative Humidity 0-95% non-condensing
Dimensions (L x W x H mm) 400 x 298 x 155
Weight (by Kg/s) 14.0
Model No. PM-800SLU-12 PM-800SLU-24
Output Power Continuous 800W
Max. Surge Power 1600W
1. Input Section
Input Nominal Voltage 120Vac or 220Vac
Input Voltage Range 60V~140Vac or 120V~280Vac
Line Low Transfer 60Vac +/- 2% or 120Vac +/- 2%
Line Low Return 65Vac +/- 2% or 130Vac +/- 2%
Line High Transfer 140Vac +/- 2% or 280Vac +/- 2%
Line High Return 130Vac +/- 2% or 260Vac +/- 2%
Input Frequency Auto 50Hz/60Hz (45Hz~75Hz)
2. Output Section
Output Voltage 100 / 110 / 115 / 120Vac or 200 / 220 / 230 / 240Vac re-settable via LCD
panel
Waveform Pure Sine Wave
Voltage Regulation (Batt. Mode) < 3% RMS for entire battery voltage range
Output Frequency ADJ. 50Hz or 60Hz +/- 0.1Hz
Total Harmonic Distortion Output THD < 3%
Maximum Load Up to short circuit
Asymmetrical Load Max. Up to nominal output power
Overload and Short Circuit Protection Automatic disconnection
Overheating Temperature Protection Acoustic warning before shut-off. Automatic restart
Power Factor 0.8
LCD Display UPS status, I/P&O/P Voltage Frequency, Load%,Battery Voltage & %,
Temperature, Model
LED Display Normal (Green), Warning (Yellow), Fault (Red)
Maximum Efficiency 85~92%
3. Battery Section
Voltage Range 12VDC (10~16VDC) 24VDC (20~32VDC)
Backup Time (at full load) Long time available
Input Frequency Range 45~70Hz
Max. Charging Current (5 steps selectable for 12V) (3 steps selectable for 24V)
> 40Amp 60/80/100Amp
4. Solar Charge Regulator-Floating
Battery Voltage 12VDC 24VDC
Charging Voltage 13.8VDC 27.7VDC
Solar Max. Peak Voltage 25.0VDC 50.0VDC
Solar Charging Working Voltage 12VDC 24VDC
Maximum Charging Current 50A
5. Audible Alarm
Battery Mode Beeping every 4 seconds
Low Battery Beeping every second
Solar Inverter Fault Beeping continuously
Overload Beeping twice per second
Temperature Compensation (Option) 3mV / cell
6. General date
AC By Pass Time (UPS Mode) <10ms max
Operation Temperature -20 to +55
Max Current at Transfer Relay 40A / AC 220V
Audible Noise Less than 55dBA (at 1M)
Relative Humidity 0-95% non-condensing
Accessory DC cable (option)
Dimensions (L x W x H mm) 400*298*155
Net Weight (by Kg/s) 14
Model No. PM-1600LC-24
Output Power Continuous 1600W
Max. Surge Power 3200W
1. Input Section
Input Nominal Voltage 110Vac or 220Vac
Input Voltage Range 60V~140Vac or 120V~280Vac
Line Low Transfer 60Vac ± 2% or 120Vac ± 2%
Line Low Return 65Vac ± 2% or 130Vac ± 2%
Line High Transfer 140Vac ± 2% or 280Vac ± 2%
Line High Return 130Vac ± 2% or 260Vac ± 2%
Input Frequency 50Hz / 60Hz (45Hz~70Hz)
2. Output Section
Output Voltage 100 / 110 / 115 / 120Vac or 200 / 220 / 230 / 240Vac
re-settable via LCD panel
Waveform Pure Sine Wave
Voltage Regulation (Batt. Mode) < 3% RMS for entire battery voltage range
Output Frequency 50Hz or 60Hz ± 0.1Hz
Efficiency > 80%
Maximum Load Up to short circuit
Asymmetrical Load Max. Up to nominal output power
Overload and Short Circuit Protection Automatic disconnection
Overheating Temperature Protection Acoustic warning before shut-off.
Automatic restart
Power Factor 0.8
3. Battery Section
Voltage Range 24VDC (20~32VDC)
Backup Time (at full load) Long time available
Input Frequency Range 45~70Hz
Max. Charging Current (3 steps selectable)
60/80/100Amp
4. Display
LCD Display UPS status, I/P&O/P Voltage Frequency, Load%,
Battery Voltage & %, Temperature, Model
LED Display Normal (Green), Warning (Yellow), Fault (Red)
5. Audible Alarm
Battery Mode Beeping every 4 seconds
Low Battery Beeping every second
Overload Beeping twice per second
Temperature Compensation (Option) 3mV / °C cell
6. General date
AC By Pass Time (UPS Mode) < 8 ms.
Operation Temperature -20 °C to +55 °C
Audible Noise Less than 55dBA (at 1M)
Relative Humidity 0-95% non-condensing
Dimensions (L x W x H mm) 450 × 298 × 190
Weight (by Kg/s) 21.0
Model No. PM-1600SLU-24
Output Power Continuous 1600W
Max. Surge Power 3200W
1. Input Section
Input Nominal Voltage 120Vac or 220Vac
Input Voltage Range 60V~140Vac or 120V~280Vac
Line Low Transfer 60Vac +/- 2% or 120Vac +/- 2%
Line Low Return 65Vac +/- 2% or 130Vac +/- 2%
Line High Transfer 140Vac +/- 2% or 280Vac +/- 2%
Line High Return 130Vac +/- 2% or 260Vac +/- 2%
Input Frequency Auto 50Hz/60Hz (45Hz~75Hz)
2. Output Section
Output Voltage 100 / 110 / 115 / 120Vac or 200 / 220 / 230 / 240Vac
re-settable via LCD panel
Waveform Pure Sine Wave
Voltage Regulation (Batt. Mode) < 3% RMS for entire battery voltage range
Output Frequency ADJ. 50Hz or 60Hz +/- 0.1Hz
Total Harmonic Distortion Output THD < 3%
Maximum Load Up to short circuit
Asymmetrical Load Max. Up to nominal output power
Overload and Short Circuit Protection Automatic disconnection
Overheating Temperature Protection Acoustic warning before shut-off. Automatic restart
Power Factor 0.8
LCD Display UPS status, I/P&O/P Voltage Frequency, Load%,
Battery Voltage & %, Temperature, Model
LED Display Normal (Green), Warning (Yellow), Fault (Red)
Maximum Efficiency 85~92%
3. Battery Section
Voltage Range 24VDC (20~32VDC)
Backup Time (at full load) Long time available
Input Frequency Range 45~70Hz
Max. Charging Current (3 steps selectable)
60/80/100Amp
4. Solar Charge Regulator-Floating
Battery Voltage 24VDC
Charging Voltage 27.7VDC
Solar Max. Peak Voltage 25.0VDC
Solar Charging Working Voltage 24VDC
Maximum Charging Current 50A
5. Audible Alarm
Battery Mode Beeping every 4 seconds
Low Battery Beeping every second
Solar Inverter Fault Beeping continuously
Overload Beeping twice per second
Temperature Compensation (Option) 3mV / cell
6. General date
AC By Pass Time (UPS Mode) <10ms max
Operation Temperature -20 to +55
Max Current at Transfer Relay 20A / AC 220V
Audible Noise Less than 55dBA (at 1M)
Relative Humidity 0-95% non-condensing
Accessory DC cable (option)
Dimensions (L x W x H mm) 450*298*190
Net Weight (by Kg/s) 21
Model No. PM-2400LC-24
Output Power Continuous 2400W
Max. Surge Power 4800W
1. Input Section
Input Nominal Voltage 110Vac or 220Vac
Input Voltage Range 60V~140Vac or 120V~280Vac
Line Low Transfer 60Vac ± 2% or 120Vac ± 2%
Line Low Return 65Vac ± 2% or 130Vac ± 2%
Line High Transfer 140Vac ¡Ó 2% or 280Vac ¡Ó 2%
Line High Return 130Vac ± 2% or 260Vac ± 2%
Input Frequency 50Hz / 60Hz (45Hz~70Hz)
2. Output Section
Output Voltage 100 / 110 / 115 / 120Vac or 200 / 220 / 230 / 240Vac
re-settable via LCD panel
Waveform Pure Sine Wave
Voltage Regulation (Batt. Mode) < 3% RMS for entire battery voltage range
Output Frequency 50Hz or 60Hz ± 0.1Hz
Efficiency > 80%
Maximum Load Up to short circuit
Asymmetrical Load Max. Up to nominal output power
Overload and Short Circuit Protection Automatic disconnection
Overheating Temperature Protection Acoustic warning before shut-off.
Automatic restart
Power Factor 0.8
3. Battery Section
Voltage Range 24VDC (20~32VDC)
Backup Time (at full load) Long time available
Input Frequency Range 45~70Hz
Max. Charging Current (3 steps selectable)
60/80/100Amp
4. Display
LCD Display UPS status, I/P&O/P Voltage Frequency, Load%,
Battery Voltage & %, Temperature, Model
LED Display Normal (Green), Warning (Yellow), Fault (Red)
5. Audible Alarm
Battery Mode Beeping every 4 seconds
Low Battery Beeping every second
Overload Beeping twice per second
Temperature Compensation (Option) 3mV / °C cell
6. General date
AC By Pass Time (UPS Mode) < 8 ms.
Operation Temperature -20 °C to +55 °C
Audible Noise Less than 55dBA (at 1M)
Relative Humidity 0-95% non-condensing
Dimensions (L x W x H mm) 450 × 298 × 190
Weight (by Kg/s) 23.0
Model No. PM-2400SLU-24
Output Power Continuous 2400W
Max. Surge Power 4800W
1. Input Section
Input Nominal Voltage 120Vac or 220Vac
Input Voltage Range 60V~140Vac or 120V~280Vac
Line Low Transfer 60Vac +/- 2% or 120Vac +/- 2%
Line Low Return 65Vac +/- 2% or 130Vac +/- 2%
Line High Transfer 140Vac +/- 2% or 280Vac +/- 2%
Line High Return 130Vac +/- 2% or 260Vac +/- 2%
Input Frequency Auto 50Hz/60Hz (45Hz~75Hz)
2. Output Section
Output Voltage 100 / 110 / 115 / 120Vac or 200 / 220 / 230 / 240Vac re-settable via LCD
panel
Waveform Pure Sine Wave
Voltage Regulation (Batt. Mode) < 3% RMS for entire battery voltage range
Output Frequency ADJ. 50Hz or 60Hz +/- 0.1Hz
Total Harmonic Distortion Output THD < 3%
Maximum Load Up to short circuit
Asymmetrical Load Max. Up to nominal output power
Overload and Short Circuit Protection Automatic disconnection
Overheating Temperature Protection Acoustic warning before shut-off. Automatic restart
Power Factor 0.8
LCD Display UPS status, I/P&O/P Voltage Frequency, Load%,Battery Voltage & %,
Temperature, Model
LED Display Normal (Green), Warning (Yellow), Fault (Red)
Maximum Efficiency 85~92%
3. Battery Section
Voltage Range 24VDC (20~32VDC)
Backup Time (at full load) Long time available
Input Frequency Range 45~70Hz
Max. Charging Current (3 steps selectable)
60/80/100Amp
4. Solar Charge Regulator-Floating
Battery Voltage 24VDC
Charging Voltage 27.7VDC
Solar Max. Peak Voltage 25.0VDC
Solar Charging Working Voltage 24VDC
Maximum Charging Current 50A
5. Audible Alarm
Battery Mode Beeping every 4 seconds
Low Battery Beeping every second
Solar Inverter Fault Beeping continuously
Overload Beeping twice per second
Temperature Compensation (Option) 3mV / cell
6. General date
AC By Pass Time (UPS Mode) <10ms max
Operation Temperature -20 to +55
Max Current at Transfer Relay 40A / AC 220V
Audible Noise Less than 55dBA (at 1M)
Relative Humidity 0-95% non-condensing
Accessory DC cable (option)
Dimensions (L x W x H mm) 450*298*190
Net Weight (by Kg/s) 23
Specificații tehnice pentru modelele 4000W, 6000W, 8000W: Model No. PM-4000LC-24
Output Power Continuous 4000W
Max. Surge Power 8000W
1. Input Section
Input Nominal Voltage 110Vac or 220Vac
Input Voltage Range 60V~140Vac or 120V~280Vac
Line Low Transfer 60Vac ± 2% or 120Vac ± 2%
Line Low Return 65Vac ± 2% or 130Vac ± 2%
Line High Transfer 140Vac ± 2% or 280Vac ± 2%
Line High Return 130Vac ± 2% or 260Vac ± 2%
Input Frequency 50Hz / 60Hz (45Hz~70Hz)
2. Output Section
Output Voltage 100 / 110 / 115 / 120Vac or 200 / 220 / 230 / 240Vac
re-settable via LCD panel
Waveform Pure Sine Wave
Voltage Regulation (Batt. Mode) < 3% RMS for entire battery voltage range
Output Frequency 50Hz or 60Hz ± 0.1Hz
Efficiency > 80%
Maximum Load Up to short circuit
Asymmetrical Load Max. Up to nominal output power
Overload and Short Circuit Protection Automatic disconnection
Overheating Temperature Protection Acoustic warning before shut-off. Automatic restart
Power Factor 0.8
3. Battery Section
Voltage Range 24VDC (20~32VDC)
Backup Time (at full load) Long time available
Input Frequency Range 45~70Hz
Max. Charging Current (3 steps selectable)
60/80/100Amp
4. Display
LCD Display UPS status, I/P&O/P Voltage Frequency, Load%,
Battery Voltage & %, Temperature, Model
LED Display Normal (Green), Warning (Yellow), Fault (Red)
5. Audible Alarm
Battery Mode Beeping every 4 seconds
Low Battery Beeping every second
Overload Beeping twice per second
Temperature Compensation (Option) 3mV / °C cell
6. General date
AC By Pass Time (UPS Mode) < 8 ms.
Operation Temperature -20 °C to +55 °C
Audible Noise Less than 55dBA (at 1M)
Relative Humidity 0-95% non-condensing
Dimensions (L x W x H mm) 600 × 415 × 260
Weight (by Kg/s) 49.2
Model No. PM-4000SLU-24
Output Power Continuous 4000W
Max. Surge Power 8000W
1. Input Section
Input Nominal Voltage 120Vac or 220Vac
Input Voltage Range 60V~140Vac or 120V~280Vac
Line Low Transfer 60Vac +/- 2% or 120Vac +/- 2%
Line Low Return 65Vac +/- 2% or 130Vac +/- 2%
Line High Transfer 140Vac +/- 2% or 280Vac +/- 2%
Line High Return 130Vac +/- 2% or 260Vac +/- 2%
Input Frequency 50Hz or 60Hz (45Hz~75Hz)
2. Output Section
Output Voltage 100 / 110 / 115 / 120Vac or 200 / 220 / 230 / 240Vac
re-settable via LCD panel
Waveform Pure Sine Wave
Voltage Regulation (Batt. Mode) < 3% RMS for entire battery voltage range
Output Frequency 50Hz or 60Hz
Total Harmonic Distortion Output THD
< 3%
Maximum Load Up to short circuit
Asymmetrical Load Max. Up to nominal output power
Overload and Short Circuit Protection
Automatic disconnection
Overheating Temperature Protection Acoustic warning before shut-off. Automatic restart
Power Factor 0.8
LCD Display UPS status, I/P&O/P Voltage Frequency, Load%,Battery
Voltage & %, Temperature, Model
LED Display Normal (Green), Warning (Yellow), Fault (Red)
Maximum Efficiency > 80%
3. Battery Section
Voltage Range 24VDC (20~32VDC)
Backup Time (at full load) Long time available
Input Frequency Range 45~70Hz
Max. Charging Current (3 steps selectable)
60/80/100Amp
4. Solar Charge Regulator-Floating
Battery Voltage 24V
Charging Voltage 27.7V
Solar Max. Peak Voltage 50.0V
Solar Charging Working Voltage 24.0V
Max. Charging Current 50A
5. Audible Alarm
Battery Mode Beeping every 4 seconds
Low Battery Beeping every second
Solar Inverter Fault Beeping continuously
Overload Beeping twice per second
Temperature Compensation (Option) 3mV / °C cell
6. General date
AC By Pass Time (UPS Mode) <10ms max
Operation Temperature -20 °C to +55 °C
Audible Noise Less than 55dBA (at 1M)
Relative Humidity 0-95% non-condensing
Accessory DC cable (option)
Dimensions (L x W x H mm) 600*415*260
Net Weight (by Kg/s) 49.2
Model No. PM-6000LC-48
Output Power Continuous 6000W
Max. Surge Power 12000W
1. Input Section
Input Nominal Voltage 110Vac or 220Vac
Input Voltage Range 60V~140Vac or 120V~280Vac
Line Low Transfer 60Vac ± 2% or 120Vac ± 2%
Line Low Return 65Vac ± 2% or 130Vac ± 2%
Line High Transfer 140Vac ± 2% or 280Vac ± 2%
Line High Return 130Vac ± 2% or 260Vac ± 2%
Input Frequency 50Hz / 60Hz (45Hz~70Hz)
2. Output Section
Output Voltage 100 / 110 / 115 / 120Vac or 200 / 220 / 230 / 240Vac
re-settable via LCD panel
Waveform Pure Sine Wave
Voltage Regulation (Batt. Mode) < 3% RMS for entire battery voltage range
Output Frequency 50Hz or 60Hz ± 0.1Hz
Efficiency > 80%
Maximum Load Up to short circuit
Asymmetrical Load Max. Up to nominal output power
Overload and Short Circuit Protection Automatic disconnection
Overheating Temperature Protection Acoustic warning before shut-off.
Automatic restart
Power Factor 1.0
3. Battery Section
Voltage Range 48VDC (42~62VDC)
Backup Time (at full load) Long time available
Input Frequency Range 45~70Hz
Max. Charging Current (3 steps selectable)
60/80/100Amp
4. Display
LCD Display UPS status, I/P&O/P Voltage Frequency, Load%,
Battery Voltage & %, Temperature, Model
LED Display Normal (Green), Warning (Yellow), Fault (Red)
5. Audible Alarm
Battery Mode Beeping every 4 seconds
Low Battery Beeping every second
Overload Beeping twice per second
Temperature Compensation (Option) 3mV /°C cell
6. General date
AC By Pass Time (UPS Mode) < 8 ms.
Operation Temperature -20 °C to +55 °C
Audible Noise Less than 55dBA (at 1M)
Relative Humidity 0-95% non-condensing
Dimensions (L x W x H mm) 600 × 415 × 260
Weight (by Kg/s) 51.4
Model No. PM-6000SLU-48
Output Power Continuous 6000W
Max. Surge Power 12000W
1. Input Section
Input Nominal Voltage 220/230/240Vac
Input Voltage Range 120V~280Vac
Line Low Transfer 120Vac +/- 2%
Line Low Return 130Vac +/- 2%
Line High Transfer 280Vac +/- 2%
Line High Return 260Vac +/- 2%
Input Frequency 50Hz or 60Hz (45Hz~75Hz)
2. Output Section
Output Voltage 200 / 220 / 230 / 240Vac re-settable via LCD panel
Waveform Pure Sine Wave
Voltage Regulation (Batt. Mode) < 3% RMS for entire battery voltage range
Output Frequency 50Hz or 60Hz
Total Harmonic Distortion Output THD
< 3%
Maximum Load Up to short circuit
Asymmetrical Load Max. Up to nominal output power
Overload and Short Circuit Protection
Automatic disconnection
Overheating Temperature Protection Acoustic warning before shut-off. Automatic restart
Power Factor 1.0
LCD Display UPS status, I/P&O/P Voltage Frequency, Load%,Battery Voltage &
%, Temperature, Model
LED Display Normal (Green), Warning (Yellow), Fault (Red)
Maximum Efficiency > 80%
3. Battery Section
Voltage Range 48VDC
Backup Time (at full load) Long time available
Input Frequency Range 45~70Hz
Max. Charging Current (3 steps selectable)
60/80/100Amp
4. Solar Charge Regulator-Floating
Battery Voltage 48V
Charging Voltage 55.2V
Solar Max. Peak Voltage 100V
Solar Charging Working Voltage 44.0V
Max. Charging Current 50A
5. Audible Alarm
Battery Mode Beeping every 4 seconds
Low Battery Beeping every second
Solar Inverter Fault Beeping continuously
Overload Beeping twice per second
Temperature Compensation (Option) 3mV / °C cell
6. General date
AC By Pass Time (UPS Mode) <10ms max
Operation Temperature -20 °C to +55 °C
Audible Noise Less than 55dBA (at 1M)
Relative Humidity 0-95% non-condensing
Accessory DC cable (option)
Dimensions (L x W x H mm) 600*415*260
Net Weight (by Kg/s) 51.4
Model No. PM-8000LC-48
Output Power Continuous 8000W
Max. Surge Power 16000W
1. Input Section
Input Nominal Voltage 220Vac only
Input Voltage Range 120V~280Vac
Line Low Transfer 120Vac ± 2%
Line Low Return 130Vac ± 2%
Line High Transfer 280Vac ± 2%
Line High Return 260Vac ± 2%
Input Frequency 50Hz / 60Hz (45Hz~70Hz)
2. Output Section
Output Voltage 200 / 220 / 230 / 240Vac re-settable via LCD panel
Waveform Pure Sine Wave
Voltage Regulation (Batt. Mode) < 3% RMS for entire battery voltage range
Output Frequency 50Hz or 60Hz ± 0.1Hz
Efficiency > 80%
Maximum Load Up to short circuit
Asymmetrical Load Max. Up to nominal output power
Overload and Short Circuit Protection Automatic disconnection
Overheating Temperature Protection Acoustic warning before shut-off. Automatic restart
Power Factor 1.0
3. Battery Section
Voltage Range 48VDC (42~62VDC)
Backup Time (at full load) Long time available
Input Frequency Range 45~70Hz
Max. Charging Current (3 steps selectable)
60/80/100Amp
4. Display
LCD Display UPS status, I/P&O/P Voltage Frequency, Load%,
Battery Voltage & %, Temperature, Model
LED Display Normal (Green), Warning (Yellow), Fault (Red)
5. Audible Alarm
Battery Mode Beeping every 4 seconds
Low Battery Beeping every second
Overload Beeping twice per second
Temperature Compensation (Option) 3mV / °C cell
6. General date
AC By Pass Time (UPS Mode) < 8 ms.
Operation Temperature -20 °C to +55 °C
Audible Noise Less than 55dBA (at 1M)
Relative Humidity 0-95% non-condensing
Dimensions (L x W x H mm) 600 × 415 × 260
Weight (by Kg/s) 55.0
Model No. PM-8000SLU-48
Output Power Continuous 8000W
Max. Surge Power 16000W
1. Input Section
Input Nominal Voltage 220/230/240Vac
Input Voltage Range 120V~280Vac
Line Low Transfer 120Vac +/- 2%
Line Low Return 130Vac +/- 2%
Line High Transfer 280Vac +/- 2%
Line High Return 260Vac +/- 2%
Input Frequency 50Hz or 60Hz (45Hz~75Hz)
2. Output Section
Output Voltage 200 / 220 / 230 / 240Vac re-settable via LCD panel
Waveform Pure Sine Wave
Voltage Regulation (Batt. Mode) < 3% RMS for entire battery voltage range
Output Frequency 50Hz or 60Hz
Total Harmonic Distortion Output THD
< 3%
Maximum Load Up to short circuit
Asymmetrical Load Max. Up to nominal output power
Overload and Short Circuit Protection
Automatic disconnection
Overheating Temperature Protection Acoustic warning before shut-off. Automatic restart
Power Factor 1.0
LCD Display UPS status, I/P&O/P Voltage Frequency, Load%,Battery Voltage &
%, Temperature, Model
LED Display Normal (Green), Warning (Yellow), Fault (Red)
Maximum Efficiency > 80%
3. Battery Section
Voltage Range 48VDC
Backup Time (at full load) Long time available
Input Frequency Range 45~70Hz
Max. Charging Current (3 steps selectable)
60/80/100Amp
4. Solar Charge Regulator-Floating
Battery Voltage 48V
Charging Voltage 55.2V
Solar Max. Peak Voltage 100V
Solar Charging Working Voltage 44.0V
Max. Charging Current 50A
5. Audible Alarm
Battery Mode Beeping every 4 seconds
Low Battery Beeping every second
Solar Inverter Fault Beeping continuously
Overload Beeping twice per second
Temperature Compensation (Option) 3mV / °C cell
6. General date
AC By Pass Time (UPS Mode) <10ms max
Operation Temperature -20 °C to +55 °C
Audible Noise Less than 55dBA (at 1M)
Relative Humidity 0-95% non-condensing
Accessory DC cable (option)
Dimensions (L x W x H mm) 600*415*260
Net Weight (by Kg/s) 55
Recommended