\ INDEX
1 Overview
2 Hardware Overview
3 Software Overview
4 System Features
Page 1
Pages 2-5
Pages 6-12
Page 13
BI0078 GTI PC Sales Literature v12 AW.indd 2 08/03/2016 17:16
01
OVERVIEW
Bailoy / GTI PC / Overview
Designed and manufactured by Bailoy in 1995, GTI PC was
one of the fi rst Windows-based PC systems in the irrigation
industry. Ever since its introduction, the hardware and
software powering its comprehensive features have been
regularly updated increasing its functionality further while
also enhancing the user experience.
GTI PC is available for sites that use either 2- or 3-core control
cables. The Gemini system is used with 2-core control cable, the
Trident system with 3-core. This makes it an ideal replacement
for older controllers such as the SC3000, CDS-DIU or Watermation
TW1 and TW2 and in most cases, can utilise the existing site
control cables, decoders and solenoids.
BI0078 GTI PC Sales Literature v12 AW.indd 3 08/03/2016 17:16
02
The GTI PC system consists of up to 4 DOUs (Decoder Output
Unit) and a fi bre-optic cable connection to a computer running
GTI software. The DOU is IP65 rated meaning it can be installed in
most environments allowing for simple retrofi tting into the existing
controller locations. If it is not possible to install the computer in the
same location, within 20m of the DOU, or a distributed system is
required, Communication Boosters can be installed meaning the
computer can be positioned within 1600m of the nearest DOU.
Each DOU is available in a 2, 3 or 4 control cable (CSG) option
with each CSG able to control up to 114 stations (109 on Gemini).
This fl exibility allows the design to be ‘made to measure’ without
the need to have unused CSGs, therefore reducing costs.
GTI PC uses multiple CSGs, which is better than single control
cable systems as a damaged CSG would mean you only lose
a small section of the system, not everything.
HARDWARE OVERVIEW
Bailoy / GTI PC / Hardware Overview
BI0078 GTI PC Sales Literature v12 AW.indd 4 08/03/2016 17:16
Bailoy / GTI PC / Hardware Overview
03
Distributed system
The GTI system can also be used as a distributed
system, where each DOU is installed close to the area
it controls. DOUs communicate with the computer
using communication boosters and telecom cable.
Each DOU is designed to report back immediately
when there are hardware issues, such as a blown
fuse. An extended test can also be performed from
the central computer.
DESIGNED TO BE
FLEXIBLE
BI0078 GTI PC Sales Literature v12 AW.indd 5 08/03/2016 17:16
04
Built-in decoder programmer
Programme, read and check your decoders
from the DOU using the GTI software.
Built-in pump start
A volt-free contact that can be used to
control pump systems. The contact is
closed when irrigation is taking place.
Rain switch input
Turn off irrigation when there is too
much rainfall.
Bailoy / GTI PC / Hardware Overview
Easy-access connector for programming decoders
BI0078 GTI PC Sales Literature v12 AW.indd 6 08/03/2016 17:16
05
EXTENSIVE HARDWARE FEATURES
Bailoy / GTI PC / Hardware Overview
Two alarm inputs
Both inputs are fully confi gurable with the alarm status
shown in the main window of the GTI software.
• The inputs can detect low system pressure, low tank
level and pump failure triggering alarms that can stop
the irrigation
• All alarm conditions are logged for reference
• Interrupted irrigation programmes can be restarted
later if required
Built-in surge protection
Each CSG output has a built-in surge protector. This device
can be replaced by the user when the need arises.
LED indicators to check DOU status
Invaluable for quickly diagnosing DOU hardware issues.
Status indicators inform user
BI0078 GTI PC Sales Literature v12 AW.indd 7 08/03/2016 17:17
06
Main software window
Bailoy / GTI PC / Software Overview
SOFTWAREOVERVIEW
GTI PC software is simple to use with guided steps for
every process and no confusing spreadsheets or multiple
windows. Once the database of site information has been
setup, the user could be irrigating in just a few minutes.
The combination of hardware and software will provide
the user with lots of features to setup and adjust
irrigation run times quickly and easily and view data
to diagnose any system issues giving precision-control
of their irrigation on a daily basis.
GTI was designed to be user friendly and specifically
based on:
• What do I want to water?
• When are my irrigation programmes scheduled to run?
• What is irrigating?
EASY TO USE
BI0078 GTI PC Sales Literature v12 AW.indd 8 08/03/2016 17:17
07
Bailoy / GTI PC / Software Overview
FLOW MANAGED SYSTEM
Flow managed system
This feature manages the hydraulic confi guration. It ensures pump capacity and
fl ow limits of the pipe distribution network are never exceeded which ensures
sprinkler heads maintain the specifi ed coverage at all times.
Confi guring pump stations:
• GTI PC can be confi gured with up to 8 independent pump stations. Each pump
will have its own hydraulic tree
• For simplicity and ease, a basic tree can be instantly created from a single click
Compensate the hydraulic behaviour for each station to allow for:
• Different valve pressure settings or elevation
• Slow-closing valves, to avoid temporarily exceeding the fl ow from the
associated pump system or in the supply pipes
The strict fl ow management creates a near constant fl ow from the pump station,
which also helps minimise pump wear.
BI0078 GTI PC Sales Literature v12 AW.indd 9 08/03/2016 17:17
08
INTUITIVE ONLINE
MANUAL
Bailoy / GTI PC / Software Overview
Easy to use screen layouts
Simple guided steps, no confusing spreadsheets or multiple windows.
Online help manual covering all aspects of the software and hardware.
Each window in the software has a help button. When selected, it opens
the manual at the correct page.
The manual also explains how to wire decoders, operate the remote
control, and has a quick-learn tutorial to get you started.
Support button
Click this button when requested by the Bailoy support technician to
gain access to GTS Support. See GTI-PB-011 for further information.
System status area
‘At a glance’ view of the next scheduled irrigation programme, pump
station flow, total water consumption for month, and the most recent
logbook entry.
Online manual always available through help button
BI0078 GTI PC Sales Literature v12 AW.indd 10 08/03/2016 17:17
09
Bailoy / GTI PC / Software Overview
Irrigation programmes
Create irrigation programmes for one, multiple or all
of your stations, for any application. With up to 256
programmes every possible setup option is available.
Setup by time (minutes) or precipitation (mm) to create
your preferred routine irrigation programmes or for when
specifi c-to-course treatments are needed.
No need to write an irrigation programme for one off
requirements. Instead a start time is chosen and irrigation
times/precipitation is set for the required stations, meaning
you could add thousands of individual programmes to the
irrigation schedule.
Remote control
As well as the DTMF Radio Remote option, the software
also offers a dedicated window that allows the operation
of a virtual radio handset on a 3G/4G enabled device
(smartphone, tablet, etc.) without the substantial fi nancial
investment required for the radio hardware, aerial and
installation costs.
The virtual handset is used to select stations for immediate
irrigation and to stack the stations in a queue when the
number of requested stations exceeds the hydraulic
limitations of the system. The codes required to select
stations are designed to be easily remembered.
Manual irrigation
Select multiple stations for manual irrigation quickly
from a list of courses and holes. Stations can be irrigated
sequentially or within the shortest time possible. Like
all other options, the manual irrigation feature is fl ow
managed, too.
Adding the optional VIP feature makes the manual irrigation
easier and visually clearer.
BI0078 GTI PC Sales Literature v12 AW.indd 11 08/03/2016 17:17
10
Bailoy / GTI PC / Software Overview
VIP maintenance centre
A feature that is used to quickly add new stations or move/delete
existing stations and sprinkler heads from the graphics without
needing support from the installer or manufacturer. Please note
VIP option required, see GTI-PB-012 for further information.
Rapid programming
Purposefully designed to setup irrigation programmes to cover
the whole area/course in just a few clicks. You can then let the GTI
system do the hard work for you.
Diagnostic test facilities
Test the operation of a single, selection of, or all stations,
with results stored in the easy-access diagnostic logbook:
• Test by station, course, hole or VIP graphically-displayed selection, CSG
• The diagnostics includes an option to pause before each hole is
tested allowing for a service technician to check the (sprinkler head)
operation without an assistant
• Diagnostic logbook allows for data to be analysed after the tests
are complete meaning the service technician can work on other
jobs while diagnostic tests are in progress
• When diagnosing sprinkler heads, stations can be given different
test durations, allowing for physical sprinkler inspections
Visually displayed diagnostics
BI0078 GTI PC Sales Literature v12 AW.indd 12 08/03/2016 17:17
11
MONITORS WATER USE
Bailoy / GTI PC / Software Overview
Water consumption records
The GTI software logs the calculated water consumption for all controller based irrigation whether
scheduled programmes, manual, remote control or diagnostic tests. Consumption from the current
or previous years can be viewed and compared as a list or visually.
Water consumption shown as list Water consumption shown visually
BI0078 GTI PC Sales Literature v12 AW.indd 13 08/03/2016 17:17
12
Operational logbook
The logbook is used to record events from multiple
programme conditions such as every time an
irrigation programme is completed or stopped.
The irrigation programmes, together with logged
information such as system faults and precipitation,
are stored for later historical reference or analysis.
The addition of VIP allows instant analysis of all faults
recorded within a selected period. As a result a service
technician can instantly recognise where a cable or joint
problem might be.
AUTO LOGBOOK
Bailoy / GTI PC / Software Overview
Logged details for further analysis
Visually diagnose actions instantly
BI0078 GTI PC Sales Literature v12 AW.indd 14 08/03/2016 17:17
13
Bailoy / GTI PC / System Features
SYSTEMFEATURES
Gemini
• For use on sites with 2-core control cables
• Suitable for retro fi tting by utilising existing control cables
• 109 stations per control cable
• Up to 16 separate control cables (CSGs)
• Built-in decoder programmer – programme, read and
check decoders from DOU using GTI software
• Built-in pump start volt-free contact
• Rain switch input – turn off irrigation when there is too
much rainfall
• Alarm sensor inputs – used to detect low system pressure
and low tank level
• Built-in surge protection
• LED indicators for instant DOU status
• Compatible with all Bailoy manufactured Gemini and
Watermation TW1 and TW2 decoders
• Available in multiple languages
Trident
• For use on sites with 3-core control cables
• Suitable for retro fi tting by utilising existing control cables
• 114 stations per control cable
• Up to 16 separate control cables (CSGs)
• Built-in decoder programmer – programme, read and
check decoders from DOU using GTI software
• Built-in volt-free pump start contact
• Rain switch input – turn off irrigation when there is too
much rainfall
• Alarm sensor inputs – used to detect low system pressure
and low tank level
• Built-in surge protection
• LED indicators for instant DOU status
• Compatible with all Bailoy manufactured Trident, SC3000
and CDS decoders
• Available in multiple languages
BI0078 GTI PC Sales Literature v12 AW.indd 15 08/03/2016 17:17
BAILOY PRODUCTS LIMITED THE OLD FORGE, HIGH STREETHARMONDSWORTH VILLAGEMIDDLESEX, UB7 0AQUNITED KINGDOM
t: +44 (0)208 897 0125e: [email protected]: bailoy.com
GTI-PB-020-0116-GB
BI0078 GTI PC Sales Literature v12 AW.indd 16 08/03/2016 17:17
\ INDEX
Overview Page 01
Hardware Overview Pages 02-03
Software Overview Pages 04-05
Software Features Pages 06-13
01
OVERVIEW
Bailoy / GTI EC / Overview
GTI EC controllers are economical irrigation systems for smaller
sites on a modest budget, yet retain many of the powerful
features found in their GTI PC stablemate. Available in Pro and
Lite editions, GTI EC customers now have a choice with how
they want to irrigate.
Both editions are available for sites that use either 2- or 3-core
control cables. The Gemini system is used with 2-core control
cable, the Trident system with 3-core. This makes them an ideal
replacement for older controllers such as the SC3000 or
Watermation TW1 and TW2 and, in most cases, can utilise the
existing site control cables, decoders and solenoids.
Forwards and backwards compatible with all equipment
manufactured by Bailoy, means both GTI EC editions are fully
upgradable or flexible to your existing infrastructure.
02
Bailoy / GTI EC / Hardware Overview
The GTI EC uses a single DOU (Decoder Output Unit) with 4 control cable outputs
(CSGs) available allowing control of up to 448 stations (436 on Gemini). The DOU is
IP65 rated so can be installed in most environments allowing for simple retrofitting
into existing controller locations.
The DOU is connected to a dedicated touch screen tablet, running GTI EC software.
This can be installed up to 10 meters from the DOU using a fibre optic cable, or up to
1600 meters using a Communication Booster.
HARDWARE OVERVIEW
03
Bailoy / GTI EC / Hardware Overview
HOST OF USEFUL FEATURES
Built-in decoder programmer
Programme, read and check your decoders from the DOU
using the GTI software.
Built-in pump start
A volt-free contact that can be used to control pump systems.
The contact is closed when irrigation is taking place.
Rain switch input
Turn off irrigation when there is too much rainfall.
Two alarm inputs
Both inputs are fully configurable with the alarm status
shown in the main window of the GTI EC software.
Alarms can optionally STOP the irrigation, for example:
• Detecting low system pressure
• Low tank level
• Pump failure
All alarm conditions are logged for later reference or can
be sent via email to the user when an alarm is raised.
Built-in surge protection
Each CSG output has a built-in surge protector. This device
can be replaced by the user when the need arises.
LED indicators to check DOU status
Invaluable for quickly diagnosing DOU hardware issues.
Status indicators inform user
04
SOFTWARE OVERVIEW
EASY TO USE
Bailoy / GTI EC / Software Overview
GTI EC software is simple to use with guided steps for
every process and no confusing spreadsheets or multiple
windows. Once the database of site information has been
setup, the user could be irrigating in just a few minutes.
The combination of hardware and software will provide
the user with lots of features to set up and adjust irrigation
run times quickly and easily and view data to diagnose any
system issues giving precision-control of their irrigation on
a daily basis.
GTI was designed to be user friendly and specifically
based on:
• What do I want to water?
• When are my irrigation programmes scheduled to run?
• What is irrigating? Deliberately uncomplicated interface
05
Bailoy / GTI EC / Software Overview
The GTI EC Pro is designed to flow manage all your
irrigation requirements.
Irrigation programmes are scheduled by Hole/Area or
station priority. The software then automatically irrigates
in the quickest and most efficient order. Alternatively, the
programme can be scheduled using the step sequence
feature. This allows users to design up to 10 unique
sequences to suit their irrigation needs.
The GTI EC Pro has a comprehensive email report and
alert feature, providing a range of diagnostic data and
alerts on programme and station issues.
The GTI EC Lite is designed to emulate older controllers
like the SC3000 and TW2 by using the step sequence
feature. This allows users to design up to 10 unique
sequences to suit their irrigation needs.
The GTI EC Lite can be upgraded to benefit from flow
management and email features by simply ordering
a feature unlock key.
TWO EC CHOICES
06
Bailoy / GTI EC / Software Features
Flow managed system
This feature manages the hydraulic configuration.
It ensures pump capacity and flow limits of the pipe
distribution network are never exceeded which ensures
sprinkler heads maintain the specified coverage at
all times.
The strict flow management creates a near constant
flow from the pump station, which also helps minimise
pump wear and reduce electrical power usage.
GTI EC Pro’s flow management
functionality allows users to
configure hydraulic zones
FLOW MANAGED SYSTEM
SOFTWARE FEATURES
GTI EC Lite upgrade option
07
User configurable Standard Irrigation Programmes
Bailoy / GTI EC / Software Features
Easy to use screen layouts
Simple guided steps, no confusing spreadsheets
or multiple windows. Very easy to use with colour
coded buttons for extra simplicity.
Status bar
Displays the name of the running (or next scheduled)
irrigation programme. It also shows the system,
internet, and rain switch hold status.
Adds water consumption column if flow managed
feature is installed (GTI EC Pro).
Irrigation programmes
Create irrigation programmes for one, multiple or
all of your stations, for any application. With up to
10 standard irrigation programmes you get plenty
of setup options.
08
Irrigation schedule
Add up to 12 programme starts per day with the option
to schedule on 7 or 14 day cycles.
Each scheduled programme is based on one of the
10 standard irrigation programmes, but can be adjusted
to the specific day or time in the schedule.
Extensive email features
• Email alerts following set number of errors occurring
during irrigation programme
• Documents containing the irrigation programme,
schedule, water consumption records, etc. can be
emailed to you
• Send an email as soon as an external alarm is raised
• Database changes can be automatically sent to
Bailoy as backup
Adjust the programme or stop a station from running
Bailoy / GTI EC / Software Features
GTI EC Lite upgrade option
09
Water consumption records
The GTI EC software logs the calculated water
consumption for all controller-based irrigation whether
scheduled programmes, manual, or diagnostic tests.
Consumption from the current or previous years can
be viewed and compared as a list or graph.
Diagnostic test facilities
Test the operation of a single, selection of, or all
stations, with results stored in the easy-access
diagnostic logbook:
• Test by station, hole or course
• Diagnostic logbook allows for data to be analysed
after the tests are complete, so users and
technicians can do other jobs while the diagnostic
test is in progress
RECORDS WATER USE
Diagnostics visually displayed on screen
Bailoy / GTI EC / Software Features
10
Operational logbook
The logbook is used to record events from
multiple conditions such as every time an
irrigation programme is completed or
stopped. The irrigation programme, together
with logged station faults etc., are stored
for later historical reference or analysis.
Manual irrigation
Manually select multiple stations for quick
irrigation, simply choose from your list of
courses and holes. Stations can be irrigated
sequentially or by shortest time possible.
The manual irrigation feature is flow
managed (GTI EC Pro).
Bailoy / GTI EC / Software Features
11
Rain hold
Prevent irrigation for a specific period or until
Rain Hold is manually disabled again.
Other features
Each station is given a unique name that the user
can immediately associate with an actual area. For
example, West Course, Hole 2, Front Tee. No need
to learn about difficult to remember electrical zones
and decoder numbers.
Easily upgrade or update your GTI EC software
through downloads or usb drive.
Remote assistance (internet required).
USER FRIENDLY FEATURES
Bailoy / GTI EC / Software Features
12
SYSTEM FEATURES
Gemini
• For use on sites with 2-core control cables
• Suitable for retro fitting by utilising existing
control cables
• 109 stations per control cable
• Up to 4 separate control cables (CSGs)
• Built-in decoder programmer – programme, read
and check decoders from DOU using GTI EC software
• Built-in pump start volt-free contact
• Rain switch input – turn off irrigation when there
is too much rainfall
• Alarm sensor inputs – used to detect low system
pressure and low tank level
• Built-in surge protection
• LED indicators for instant DOU status
• Compatible with all Bailoy manufactured Gemini
and Watermation TW1 and TW2 decoders
• Available in multiple languages
Bailoy / GTI EC / System Features
109 STATIONS
PER CONTROL CABLE
13
Trident
• For use on sites with 3-core control cables
• Suitable for retro fitting by utilising existing control cables
• 112 stations per control cable
• Up to 4 separate control cables (CSGs)
• Built-in decoder programmer – programme, read and
check decoders from DOU using GTI EC software
• Built-in volt-free pump start contact
• Rain switch input – turn off irrigation when there is too
much rainfall
• Alarm sensor inputs – used to detect low system pressure
and low tank level
• Built-in surge protection
• LED indicators for instant DOU status
• Compatible with all Bailoy manufactured Trident, SC3000
and CDS decoders
• Available in multiple languages
112 STATIONS
PER CONTROL CABLE
Bailoy / GTI EC / System Features
BAILOY PRODUCTS LIMITED THE OLD FORGE, HIGH STREET HARMONDSWORTH VILLAGE MIDDLESEX, UB7 0AQ UNITED KINGDOM
t: +44 (0)208 897 0125 e: [email protected] w: bailoy.com
GTI-PB-015-1017-GB
Bailoy / GTS Support
Your irrigation system is a vital component in the smooth
running of your site and one in which you have invested
a lot of time and money.
Whether your system seems to have a fault, you want to
make changes to increase irrigation efficiency, or you just
want to check how to do something in the software,
GTS Support will provide a solution.
GTS SUPPORTFOR GTI SYSTEMS
HELPS GETTHE MOST
OUT OF YOUR SYSTEM
02
Bailoy / GTS Support
01
• 1, 3 and 5 year agreements available
• Gold and Silver levels
• System support via telephone, email or remote session
• On-site support and diagnostics
• DOU controller replacements and repairs
SUPPORTS YOUIN MANY WAYS
REMOTE & ON-SITESUPPORT
Bailoy / GTS Support Bailoy / GTS Support
Telephone supportWhether you have a simple question on how to do something or a
technical issue, just call the helpline number +44 (0) 208 897 0125and a technician will help you through your issue.
Available 8.30am to 5pm GMT weekdays (excluding UK Bank
& Public Holidays)
Email supportIf you have a more complex issue and want to explain it in writing, in
more detail, or it is outside of telephone support hours then you can email
We aim to reply to all emails within one business day and where necessary
we will send technical bulletins, explanatory notes or manuals to help you
resolve the issue.
SUPPORT IN THE WAY THAT SUITS YOU
TELEPHONEAND EMAILSUPPORT
03 04
QUICKRESPONSE
Remote supportWe can connect to your computer over the internet. Once you
have approved the remote session the technician can work on
the problem without the need for you to be present.
Onsite assistanceWhen the situation requires a site visit, Bailoy can send a
technician to you. This may be for employee training or to
reconfigure your system databases and hydraulics after you
have installed new greens or tees.
For more information on all Bailoy support and services,
visit www.bailoy.com or call +44 (0) 208 897 0125.
GTS SUPPORTGOLD LEVEL
UNLIMITEDSUPPORT
• Unlimited next business day DOU controller replacement. Including surge damage
• Unlimited telephone, email and remote support
• Free software updates
• Discounted software upgrades
• Database backup and restore service
• Discounts on additional services such as site visits, VIP site graphics
Telephone and email support. 8.30am – 5pm GMT. Excluding weekends & Bank Holidays.
Remote support and diagnostics. 8.30am – 5pm GMT. Excluding weekends & Bank Holidays.
Next business day replacement DOUs
3 business day replacement DOUs
DOU failure. Including surge cover
Current version updates. Software & firmware
Database backup and storage
Database recovery and re-installation
Remote pre-season diagnostic check-up
Remote post season diagnostic check-up
Remote database adjustment assistance
Additional services
New version upgrades. Software & firmware
Unlimited
Unlimited
Yes
n/a
Unlimited events
Yes
Yes
Yes
Yes
Yes
Yes
20% Discount
50% Discount
Bailoy / GTS Support Bailoy / GTS Support
05 06
STRONGSUPPORT
GTS SUPPORTSILVER LEVEL
• Three business day DOU controller replacement. Including surge damage. 1 event per agreement year
• Telephone, email and remote support. 2 events per agreement year
• Free software updates
• Database backup and restore service
2 events per agreement year
2 events per agreement year
-
Yes
1 event per agreement year
Yes
Yes
List price
25% discount
25% discount
List price (hourly rate)
List price
List price
Telephone and email support. 8.30am – 5pm GMT. Excluding weekends & Bank Holidays.
Remote support and diagnostics. 8.30am – 5pm GMT. Excluding weekends & Bank Holidays.
Next business day replacement DOUs
3 business day replacement DOUs
DOU failure. Including surge cover
Current version updates. Software & firmware
Database backup and storage
Database recovery and re-installation
Remote pre-season diagnostic check-up
Remote post season diagnostic check-up
Remote database adjustment assistance
Additional services
New version upgrades. Software & firmware
Bailoy / GTS Support Bailoy / GTS Support
07 08
WHAT IF I DECIDE NOT TO TAKE OUT GTS SUPPORT?
For those users who are not covered by GTS Support, Bailoy
offer a Pay As You Go service for system diagnostic and software
issues and hardware repairs.
You can contact us by telephone or by email and we will give you
an estimate on the time required to either fix your issue or guide
you through any updates or changes you are trying to make,
along with a timescale to do the work.
Support is charged for the first 15 minutes and then in 15 minute
increments thereafter.
Please call for current rates.
GTS SUPPORTPAY AS YOU GO
List price (hourly rate)
List price (hourly rate)
-
-
-
Call for pricing
List price
List price
List price
List price
List price (hourly rate)
List price
List price
Telephone and email support. 8.30am – 5pm GMT. Excluding weekends & Bank Holidays.
Remote support and diagnostics. 8.30am – 5pm GMT. Excluding weekends & Bank Holidays.
Next business day replacement DOUs
3 business day replacement DOUs
DOU failure. Including surge cover
Current version updates. Software & firmware
Database backup and storage
Database recovery and re-installation
Remote pre-season diagnostic check-up
Remote post season diagnostic check-up
Remote database adjustment assistance
Additional services
New version upgrades. Software & firmware
ASK FORSUPPORT
Call us on: +44 (0) 208 897 0125
Email us at: [email protected]
Visit us at: www.bailoy.com
09
Bailoy / GTS Support
BAILOYPRECISIONIRRIGATIONCONTROLSYSTEMS
BAILOY PRODUCTS LIMITED THE OLD FORGE, HIGH STREETHARMONDSWORTH VILLAGEMIDDLESEX, UB7 0AQUNITED KINGDOM
t: +44 (0)208 897 0125f: +44 (0)208 759 8202e: [email protected]: bailoy.com
GTI-PB-011-1214-GB