7/30/2019 Command Center User Manual
1/16
Command Center
User Manual
Y50016-02
7/30/2019 Command Center User Manual
2/16
09-27-06 1
1 Introduction........................................................................................................2
1.1 System Requirements ...................................................................................................... 2
2 Modes of Operation............................................................................................2
2.1 Passive Mode.................................................................................................................... 2
2.2 Active Mode...................................................................................................................... 2
3 Getting Started ...................................................................................................3
4 Communication ..................................................................................................4
5 Operator Screen .................................................................................................4
5.1 Passive Mode.................................................................................................................... 4
5.2 Active Mode...................................................................................................................... 5
5.3 Individual Arc Control.................................................................................................... 65.4 Charts ............................................................................................................................... 6
6 System Interface .................................................................................................7
7 Set Points.............................................................................................................8
8 Diagnostics ..........................................................................................................9
9 Preferences....................................................................................................... 10
9.1 General Preferences ...................................................................................................... 10
9.2 Data Logging.................................................................................................................. 119.3 Other Options ................................................................................................................ 12
10 Miscellaneous Features................................................................................ 13
10.1 Save and Restore System Configuration.................................................................. 13
10.2 View Saved Weld Data............................................................................................... 13
10.3 Heat Input Analysis Tool........................................................................................... 1410.3.1 Calculation Domain.............................................................................................................................1410.3.2 Statistics...............................................................................................................................................1510.3.3 Cursor Values ......................................................................................................................................1510.3.4 Additional Features .......... ........... .......... ........... .......... ........... .......... ........... .......... ........... .......... ..........1510.3.5 Save Report..........................................................................................................................................15
7/30/2019 Command Center User Manual
3/16
09-27-06 2
1 IntroductionCommand Center is an application for high-level monitoring and controlling of multiple-arcsystems, including systems used for Submerged Arc welding. It is designed for ease of use and
convenience for operators and administrators.
1.1 System RequirementsCommand Center is designed to run under Microsoft Windows NT, 2000, XP, and up.
For best performance, it is recommended to run Command Center on a PC with at least 64 MB
of RAM, and a processor speed of 300 MHz or higher. If Command Center is used to control asystem of arcs, it is not recommended to run other applications on the same computer as
Command Center.
2 Modes of OperationCommand Center may be used in several distinct ways for different applications. It can be usedstrictly as a monitoring tool in the case where the arc system is controlled by a PLC or similar
controller. It can also be used as a controlling tool if no external controller is present.
2.1 Passive ModeIn Passive Mode, Command Center has absolutely no control over any aspect of the operation ofthe arc system; it acts strictly as a monitoring tool. For applications where the arcs are
controlled by a PLC or a user interface such as the PF10A, this mode adds a measure of security
so that the user of Command Center cannot interfere with the operation of the arcs (i.e.accidentally clicking the Start/Stop buttons). Passive Mode is Command Centers default
mode of operation. To enable or disable Passive Mode, see 9.1.
2.2 Active ModeIn Active Mode, Command Center is allowed control over the arc system, including the ability tostart and stop the arcs, change set point values, and change System Interface settings. Command
Center should be in Active Mode only if there is no external controller (PLC or user interfacesuch as PF10A) that controls the arc system, or if it is absolutely necessary to change set pointsor System Interface settings from Command Center. To enable or disable Active Mode, see 9.1.
Note: If Command Center detects a PF10A User Interface attached to the system, it will default
to Passive Mode and not allow the user to enter Active Mode.
7/30/2019 Command Center User Manual
4/16
09-27-06 3
3 Getting StartedCommand Center can be installed from the Submerged Arc Utilities CD distributed by Lincoln
Electric. After the CD is installed, to start the program, click the Windows Start button, then
navigate to Programs Lincoln Electric Submerged Arc Utilities Command Center.
The program starts with a blank window, and
expects the user to click the Open Arc
Configuration button, or select File OpenArc Configuration from the menu. The Arc
Configuration file is a text file that describes
the relationships of individual machines to eachother and their respective arc. This file is
required for Command Center to run properly.
An Arc Configuration file is generated by the
Submerged Arc Cell Configuration utilityincluded with the Submerged Arc Utilities
package.
Once all connections have been established
successfully, several tabs will appear near the
top of the window. Clicking on different tabs will reveal different pages with various content andcontrols. The following sections describe each page in detail.
Figure 3.1: Starting Command Center.
7/30/2019 Command Center User Manual
5/16
09-27-06 4
4 CommunicationAfter Command Center opens the Arc
Configuration file, it establishesconnections to all machines specified in
the file. It also creates a graphical
representation of the arc system in theform of a tree, as in Figure 4.1.
Each item in the tree represents either apower source that is part of the arc
system, or the System Interface module
required to link together multiple arcs.
The Close Communications button may
be clicked at any time to close the
connections to all machines and resetCommand Center to how it looked when
it was first started.
5 Operator ScreenIn the Operator Screen page, Command
Center displays a detailed control panel foreach arc in the system, as shown in Figure
5.1.
Each panel displays its respective arcs
voltage, current, and wire feed speed, as
well as numerous controls for modifyingthe arcs parameters.
5.1 Passive ModeUnder Passive Mode (See 2.1), all controlsin the Operator Screen are grayed out
(disabled). In this case, the Operator Screen
is only useful for monitoring arc current,voltage, wire feed speed, and status.
Figure 4.1: Communication tab, connected to a 5-arc system.
Figure 5.1: Operator Screen in Passive Mode, monitoring multiple ar
7/30/2019 Command Center User Manual
6/16
09-27-06 5
The Arc light indicates whether or not an arc is present. If the light is black, no arc is present
and no voltage is being generated. If the light is light-blue, there is an arc present. If the light isyellow, then there is voltage being generated, but no arc is present (an open-circuit state).
The Status light indicates whether or not the machine is experiencing any faults. If the light is
green, no faults are present. If the light is flashing red, the machine is in a faulted state and needsto be diagnosed. Double-clicking on the light will cause Command Center to go directly to the
Diagnostics page (See 8).
The Pipe Identification field can be used to record the part number of the current part being
welded. This field is used for data logging purposes (See 9.2).
5.2 Active ModeUnder Active Mode, all controls for
modifying arc parameters become enabled,
and the Start and Stop buttons becomevisible at the bottom of the screen, as
shown in Figure 5.2.
The Workpoint and Trim values can be
modified by using the up- and down-arrow
buttons, or by entering values directly into
the provided text fields.
The Cold Inch buttons allow the user to
feed the wire back, forward, or fast forward.
The back and forward buttons feed thewire at 50 ipm, and fast forward feeds at
200 ipm.
If the machine is in a faulted state, a
Reset button will appear to the right of
the Status light. Thisbutton enables the user to
clear the fault and bring
the machine back to aready state. Note that, in
Passive Mode, the Resetbutton will not appear.
At the bottom of the Operator Screen, there are large Start and Stop buttons, which are used
to trigger the arc system. When Start is clicked, all arcs will be triggered. The Stop buttonwill stop all arcs unconditionally. In addition, the Stop button that appears in the bottom status
bar may also be used to stop the machines.
Figure 5.2: Operator Screen in Active Mode, monitoring multiple arc
Figure 5.3: A faulted arc with visible Reset Fault button.
7/30/2019 Command Center User Manual
7/16
09-27-06 6
5.3 Individual Arc ControlOne of the optional features of Active Mode is the ability to start and stop each arc individually,or to start and stop a subset of the arcs (To enable this feature, see 9.1). When this feature is
enabled, each arc
will appear asFigure 5.4, withStart and Stop
buttons for that
particular arc.
In addition, each
arc will have a Group check box. The big Start and Stop buttonsat the bottom of the Operator Screen will change to Start Group
and Stop Group, meaning that these buttons will now only start
and stop arcs that have the Group box checked.
5.4 ChartsThe Charts tab within the Operator Screen
page contains charts that log voltage, current,
and wire feed speed data whenever the arcsare running. Using the buttons on top, it is
possible to save the data, clear the graphs,
and pause the graphs.
Saving the data will generate a comma-
delimited file that can be viewed with aspreadsheet application like Microsoft Excel,or viewed at a later time with Command
Centers built-in data viewer (See 10.2).
It is also possible to perform Heat Input
Analysis on the collected data from this
screen by clicking the Heat Input Analysisbutton (See 10.3).
As data continues to collect, the charts will
scroll to reflect the latest data points. Toreview previous data points, use the scroll bar at the bottom of the charts to scroll to the desired
position.
Clicking on one of the Arc tabs at the bottom (Arc 1, Arc 2, etc.) will highlight that arcs
data trace within the charts.
Figure 5.4: An arc with Individual Start/Stop enabled.
Figure 5.5: Charts of Current, Voltage, and Wire Feed Speed.
7/30/2019 Command Center User Manual
8/16
09-27-06 7
6 System InterfaceThe System Interface tab offers full
control over the phase relationships ofeach arc with respect to the others. In
addition, it allows the operator to set
each arcs Weld Mode.
The Weld Mode can be set by double-
clicking on a number listed in the list-box on the right. Next to the Mode
number is a description of the wire size
appropriate for the mode, and the
process description.
The different slider controls can be used
to set each arcs Phase offset (indegrees), Balance (percent duty cycle),
and DC Offset.
The Frequency field specifies the frequency (in Hertz) of the current arcs wave shape.
However, if the Synchronize check box is checked, all arcs will default to the frequency of the
selected arc.
The Arc tabs near the top of the page (Arc 1, Arc 2, etc.) allow switching between different
arcs.
Important: In Passive Mode, all of the controls mentioned above are disabled.
Figure 6.1: System Interface tab.
7/30/2019 Command Center User Manual
9/16
09-27-06 8
7 Set PointsThe Set Points tab allows the operator to
change different settings in each arc foreach state of the weld. The state can be
selected from the bottom graphical
representation of a weld process. Thesettings for the Weld 1 state are always
displayed in the bottom center column for
reference.
To change a setting, click inside the
desired text box, type in the new value,
and press Enter.
The Arc tabs near the top of the page
(Arc 1, Arc 2, etc.) allow switchingbetween different arcs.
The Summary button will bring up awindow that contains all attributes in all states grouped together in one list.
Important: In Passive Mode, these settings are disabled and can only be monitored.
Figure 7.1: Set Points tab with Weld 1 state selected.
7/30/2019 Command Center User Manual
10/16
09-27-06 9
8 DiagnosticsThis page diagnoses problems when one or
more machines enters a faulted state. The tophalf of the page contains diagnostics for the
selected arcs Master, and the bottom half for
the selected arcs Slave(s).
The Refresh button will repeat the
diagnostic process on all arcs. The ResetFault button will clear all faults on the
current arc and bring it out of the faulted
state.
Note: In Passive Mode, the Reset button is
disabled.
Figure 8.1: Diagnostics tab with a faulted arc.
7/30/2019 Command Center User Manual
11/16
09-27-06 10
9 PreferencesThe Preferences window allows the user to set
several options to define and fine-tune CommandCenters behavior. The preferences can be accessed
by selecting File Preferences from the menu.
9.1 General PreferencesThe first tab in the Preferences window contains
options that affect the overall behavior of Command
Center. These options include:
Enable Passive Mode: If checked, thischeck box brings Command Center into
Passive Mode (See 2.1). If it is unchecked,Command Center will be in Active Mode (See 2.2), and the following three options will
become enabled:
Show start/stop buttons: This check box shows or hides the Start and Stop buttons onthe Operator Screen, as well as the Stop button on the Status Bar. Uncheck this box ifstarting and stopping the arcs is not desired, but changing parameters (set points, system
interface, etc.) is still necessary. (This option is only valid in Active Mode)
Allow individual arc start/stop: This check box enables or disables the individual arcstart/stop feature when in Active Mode (See 5.3).
Stop all welding when any one arc becomes faulted: If checked, this option will causeCommand Center to stop all other arcs when any one arc becomes faulted, or if
Command Center loses its connection to any of the arcs, or if Command Center is closed.
(This option is only valid in Active Mode)
Remote Fault Watchdog Timeout: It is possible that a machine may lose its connectionto the computer running Command Center (for example, if the computer is turned off
abruptly, or if a network cable is unplugged or severed). This option allows the machine
to become faulted after a certain period of inactivity from the computer runningCommand Center. This option specifies the amount of time (in seconds) that every
machine in all arcs will wait until becoming faulted after receiving no signal from
Command Center. In Active Mode, this setting is mandatory and has a minimum of 10seconds. In Passive Mode, this setting is disabled. (Note: with this setting enabled,
closing Command Center normally or closing
connections by clicking the Close Communications
button will not generate a fault)
Show Travel Carriage Controls: If the arc systemcontains a compatible Travel Carriage module, this
option becomes enabled, and checking this option
Figure 9.1: General Preferences window.
Figure 9.2: Travel Carriage controls.
7/30/2019 Command Center User Manual
12/16
09-27-06 11
would enable the Travel Carriage controls at the bottom of the Operator Screen, as shown
in Figure 9.2. These controls allow setting the travel speed and causing the travel carriageto move forward and backward.
Disable screen saver: If checked, this option prevents the Windows screen saver fromstarting while Command Center is running.
Arcs file directory: This is the default directory in which Command Center searches forArc Configuration (.arcs) files when the Open Arc Configuration button is clicked.Click the Browse button to select a directory on the computer.
Machine Configuration File Directory: This is the default directory in which CommandCenter saves and opens Machine Configuration files (See 10.1)
9.2 Data LoggingCommand Center contains flexible data loggingfeatures that enable it to record data files containing
weld information with minimal user interaction. The
following options are available in the Data Loggingtab of the Preferences window.
Enable automatic data logging: Thisenables or disables the data logging featureentirely. If it is disabled, the next four options
will also become disabled.
Data directory: This is the directory whereCommand Center will save data filesautomatically. Click the Browse button to
select a directory on the computer.
Maintain a single log file as long as theprogram is running: If this data logging method is selected, Command Center willcreate a log file and write to it for the duration of the programs execution.
Start a new log file after a certain number of data points: With this data loggingmethod, Command Center will wait until the specified number of data points has beenaccumulated, then start a new log file.
Start a new log file after a certain number of welds: With this data logging method,Command Center will wait until the specified number of welds has been accumulated,
then start a new log file. A weld is defined as follows: When any one arc is started, aweld has begun. The weld does not end until all arcs have stopped.
Maximum data points allowed on graphs: When a large amount of data accumulates inthe data charts of the Operator Screen, it can degrade the performance of Command
Center. This option sets the maximum number of data points that can be displayed in thecharts. If more data is added to the charts than the maximum allowed, the charts are
cleared and the data is saved to the current log file (if data logging is enabled).
Figure 9.3: Data Logging preferences.
7/30/2019 Command Center User Manual
13/16
09-27-06 12
File Naming Options: These options specify how the automatic log files will be named.The file name can begin with a custom text prefix, and can also include the PipeIdentification (located on the Operator Screen), and the current date and time.Note: the
file naming options are saved in the .arcs file currently open.
9.3 Other Options Round off Current, Voltage, WFS: If
checked, this option will cause the Operator
Screen to display Current, Voltage, and Wire
Feed Speed in whole numbers instead ofdecimals. For example, instead of 56.7 V, it
will display 56 V.
Show state timers in seconds, notmilliseconds: In the Set Points tab, severalwelding states (Start, UpSlope, Crater, etc.)
have timers that specify how long the arc will
remain in that state. By default, these statetimers are displayed and entered in
milliseconds. This options allows showing the
timers in seconds.
Increment Workpoint by: This specifies the amount by which the Workpoint value isincremented with the Up/Down buttons in the Operator Screen (See 5.2).
Increment Trim by: This specifies the amount by which the Trim value is incrementedwith the Up/Down buttons in the Operator Screen (See 5.2).
Wire feed speed for cold-inching: This sets the speed of the wire when the Cold Inchbuttons are clicked in the Operator Screen (See 5.2). Wire feed speed for fast cold-inching: This sets the speed of the wire when the Fast
Cold Inch button is clicked in the Operator Screen (See 5.2).
Chart Options: These four check boxes select which charts are shown in the Charts tabof the Operator Screen (See 5.4). These include Current, Voltage, Wire Feed Speed, and
Travel Speed (Select Travel Speed only of a compatible Travel Carriage module is
installed in the arc system).
Measurement Standard: This allows the user to select the measurement standard(English or Metric) for quantities displayed in Command Center. For example, when
English is selected, all wire feed speed quantities will appear as inches per minute;
when Metric is selected, these quantities will appear as meters per minute.
Figure 9.4: Miscellaneous preferences.
7/30/2019 Command Center User Manual
14/16
09-27-06 13
10Miscellaneous Features
10.1Save and Restore System ConfigurationThe Save and Restore System Configuration options, found inthe File menu, allow to save all settings for all arcs (including
Set Points) once the desired weld performance has been
achieved, and restore those settings to the arcs at a later time.The number of configuration files that will be saved depends on
the number of arcs in the system.
When saving settings, Command Center will prompt the user to
enter a file name. This name will be used as the name for allconfiguration files in the set, with different extensions.
10.2View Saved Weld DataThe View Saved Weld Data option, found in the File
menu, allows viewing data traces that were saved byCommand Center during automatic data logging or fromthe Charts section of the Operator Screen (See 5.4).
When a data file is opened, it will appear as a separatewindow that contains charts with data read from the data
file.
To review all of the data in the trace, use the scroll bar at
the bottom of the charts.
Clicking on one of the Arc tabs at the bottom (Arc 1,
Arc 2, etc.) will highlight that arcs data trace within the charts.
It is also possible to perform Heat Input Analysis on the collected data from this screen by right-clicking within the charts and selecting Heat Input Analysis from the popup menu.
Figure 10.1: Save and Restoremenu options..
Figure 10.2: Viewing a saved data file.
7/30/2019 Command Center User Manual
15/16
09-27-06 14
10.3Heat Input Analysis ToolThe Heat Input Analysis window,as shown in Figure 10.3, can be
accessed by clicking the Heat
Input Analysis button in the Chartssection of the Operator Screen
(See 5.4), or by selecting Heat
Input Analysis from the popup
menu in the Saved Data Viewerwindow (See 10.2).
Analyzing the amount of heatdeposited during a weld can be
used to infer certain characteristics
of the weld. It can potentially beused as a measure of weld quality,
although predicting weld quality is not one of the goals of this application, since weld quality
depends on numerous other variables.
For heat input analysis to be as accurate as possible, the following input parameters must be
specified by the user:
Distance from Lead: In the upper right-hand area, the user must specify the distance (ininches) of each arc from the lead arc (if applicable). If a certain arc is the lead arc, its
distance value should be 0.
Wire Diameter: In the upper right-hand area, the user must specify the diameter (ininches) of the wire used in each arc.
Travel Speed: In the lower right-hand area, the user must specify the travel speed (ininches per minute), which is the speed at which the arc system was moving relative to the
work.
Metal Density: In the lower right-hand area, the user must specify the density (in poundsper cubic foot) of the metal of which the wire was composed. For example, the density
of steel is about 490 lb/ft3.
With every change to the above variables, the calculations will automatically update themselves.
All of these settings are saved in the Windows registry for future use.
10.3.1 Calculation DomainThe user may restrict the calculations to a specificportion of the data (for example, if the data contains
more than one weld, or if a weld contains an
undesirable spike in the beginning or end). The lower
Figure 10.4: Restricting calculation limits.
Figure 10.3: Heat Input Analysis window..
7/30/2019 Command Center User Manual
16/16
09-27-06 15
and upper limits for the calculation are denoted by thin colored bars (or cursors) that, by
default, appear at the beginning and end of the weld trace. These limits are movable by clickingand dragging the colored bars, and moving them with the mouse along the x-axis.
Similarly, the user can right-click anywhere in the chart area and select Low Limit Here or
High Limit Here to automatically move the lower or upper limit cursor to the position of themouse.
10.3.2 StatisticsThe Statistics tab in the lower left corner of the windowcontains the following data, which is dynamically
calculated when any of the input variables change, or
when the limits for the calculation are changed. Note that
this data is calculated only between the limits defined bythe limit cursors, as stated above.
10.3.3 Cursor ValuesThe Cursor Values tab in the lower left corner of thewindow contains instantaneous data at the position of the
lower and upper limit cursors. It also contains the
difference (delta) between the upper and lower limits.(This data is also updated automatically whenever the
limits are repositioned).
10.3.4 Additional FeaturesIt is possible to zoom into and out of the chart by clickingthe + (zoom in) or (zoom out) buttons which appear
in the lower left corner of the chart. The zoom factor is 2x.
Double-clicking within the chart area will enable a tool-tip
which follows the mouse cursor and displays they-value at
the current mouse position. Double-clicking a second timewill change the tool-tip to display thex-value at the current
mouse position, which is the number of inches from the
beginning of the weld.
10.3.5 Save ReportIt is also possible to save the calculated data to a tab-delimited text file. To save a file, click the
Save Report button in the lower right corner of the window. The program will then bring up a
standard Windows save dialog, where the user can find the location to save the file.
Figure 10.5: Statistics tab.
Figure 10.6: Cursor Values tab.
Figure 10.7: Enabling the tool-tip.