SUPPLEMENT 2TO
SECTIONS 14 & 15
DESIGN SERIESELEVATIONS
assurance.
Man
ual o
n w
eb -[
06/0
3]
Supplement - 2 g Casework Design SeriesPage 1 of 30
278
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
SUPPLEMENT - 2CABINET DESIGN SERIES - CDS
THE FOLLOWING CASEWORK ILLUSTRATIONS ARE ADOPTED AS DESIGN STANDARDS ANDPROVIDED TO ASSIST ARCHITECT / DESIGN PROFESSIONALS AND CASEWORK USERS INSELECTING TYPICAL DESIGNS. THESE ILLUSTRATIONS ARE NOT INTENDED TO LIMIT ORRESTRICT CREATIVITY, OR BE ALL INCLUSIVE.
In utilizing the CDS numbering system, it is not necessary to show casework elevations in your architecturaldrawings. However, it is necessary to show a plan view with each CDS number indicated along with thewidth, height, and depth in inches (Example: “102-36x30x18”). Cabinet dimensions indicate the nominaloutside dimension (floor to top of countertop for height and face of finished wall to face of cabinet door fordepth). Fabricators are permitted a tolerance of 1/2” plus/minus in width only.
If other designs are desired than those provided for in the CDS system, they may be indicated by selectingthe CDS number most closely representing the desired design, followed by the letter "M" and a descriptionor illustration of the design modification. (Example: "102M - 2 shelves - 36x30x18" or "102M - no shelves -36x30x18"). If the CDS numbering system is used in conjunction with cabinet elevations on architecturaldrawings, the cabinet elevations shall govern on any conflict between the requirements of the elevationand/or the CDS number.
The following casework heights are recommended for various school grades, subject to ADA requirements:
Kindergarten - Grade 1 = 24"Grades 2 - 3 = 27"Grades 4 - 6 = 30"Grades 7 - 9 = 33"Grades 10 and above = 36"
The CABINET DESIGN SERIES are subdivided as follows:
Base Cabinets w/o Drawers = 100 SeriesBase Cabinets w/ Drawers = 200 SeriesWall Hung Cabinets = 300 SeriesTall Storage Cabinets = 400 SeriesTall Wardrobe Cabinets = 500 SeriesLibrary Cabinets = 600 SeriesMoveable Cabinets = 700 Series
ALL HARDWARE AND ACCESSORIES SHALL BE AS APPROVED BY THESE STANDARDS ANDLISTED IN THE INSTITUTE’S SEPARATELY PUBLISHED "APPROVED HARDWARE SUPPLEMENT"
WHICH IS UPDATED ANNUALLY.
GENERAL NOTES: 1. 100 or 200 Series cabinets may be converted into moveable cabinets by prefixing a “7” to the number.2. Moveable cabinets shall be equipped with adequate approved casters for the intended load capacity.3. Cabinet Design Series #'s 728, 729, 735, 736, 737, 738, 739 require metal angle reinforced corners.4. Carts and rolling tall storage cabinets with doors, lacking any horizontal and/or vertical stabilizing
dividers, require a diaphragm bottom; specifically Cabinet Design Series #'s 702, 712, 716, 722, 743,744, 746, 747, 750, and 751.
Man
ual o
n w
eb -[
06/0
3]
Supplement - 2 g Casework Design SeriesPage 2 of 30
279
100 SERIES, BASE CABINETS w/o DRAWERS
117 120 1211/4" Sliding Glass Doors Open
111 112 1163/4" Sliding Doors
with Vertical Divider
106 107 1103/4" Sliding Doors 1/4" Sliding Glass Doors Open
without Vertical Divider
100 101 102Open
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
Man
ual o
n w
eb -[
06/0
3]
Supplement - 2 g Casework Design SeriesPage 3 of 30
280
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
100 SERIES, BASE CABINETS w/o DRAWERS(Continued)
148 150 151Removable Back / Sink Sink / 6" Apron Sink / 6" Apron4" Apron Behind Doors
141 142 146Removable Back / Sink Removable Back / Sink Removable Back / Sink4" Apron Behind Door 4" Apron Behind Doors 3/4" Sliding Doors
4" Apron Behind Doors
132 136 1403/4" Sliding Doors Open / Sink
Removable Back4" Apron
122 130 131
Man
ual o
n w
eb -[
06/0
3]
Supplement - 2 g Casework Design SeriesPage 4 of 30
281
100 SERIES, BASE CABINETS w/o DRAWERS(Continued)
155a 156 157Section Detail of Removable Back Removable Back
No Base Sink / 6" Apron Sink / 6" Apron
154 154a 155ADA Sink w/ Partial 8" Base Section Detail of ADA Sink w/ Out Base
Partial 8" Deep Base
152 153 153aSink / 6" Apron ADA Sink Section Detail of
Removable Base / Toe Removable Base / ToeSupported on Clips
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
hh
158ADA Removeable Cabinet Front, Base
and Heigth Adjustable Countertop
NOTES FOR CABINET 158:
Cabinet doors and sink apron mounted to a removable(for ADA compliance) frame, secured to adjoining wall orcabinets to the left and right.
Base removable for ADA compliance.
Countertop to be self contained with side mounting cleatswhich can be used to secure it at standard and ADA com-pliant height requirements.
Ends of adjoining countertops and cabinets shall be flushand considered finished ends.
Man
ual o
n w
eb -[
06/0
3]
Supplement - 2 g Casework Design SeriesPage 5 of 302
282
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
100 SERIES, BASE CABINETS w/o DRAWERS(Continued)
179 180 182Retractable Towel Rack Open
176 177 178Blind Corner Range Tray Storage
1/4" Dividers
170 171 172Open
160 161 162Cart Storage Cart Storage Cart Storage
Hardwood Side Guides Hardwood Side Guides Hardwood Side Guides
Man
ual o
n w
eb -[
06/0
3]
Supplement - 2 g Casework Design SeriesPage 6 of 30
283
100 SERIES, BASE CABINETS w/o DRAWERS(Continued)
189 190 191Drawing Board Rack Storage Apron Storage Apron
192 193 194Storage Apron Countertop Support Countertop Support
Floor & Wall Mounted Floor & Wall Mounted
186 187 188Corner Sliding Tray & Sliding Trays
Lift Up Shelf
195 196 197Countertop Support Corner / Lazy Susan Corner / Lazy Susan
Wall Mounted
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
Man
ual o
n w
eb -[
06/0
3]
Supplement - 2 g Casework Design SeriesPage 7 of 30
284
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
198 199Ceramics Drying Ceramics Drying
Includes Adjustable Metal Frame Includes Sliding Metal FrameShelves w/ Galvanized Wire Mesh Shelves w/ Galvanized Wire Mesh
100 SERIES, BASE CABINETS w/o DRAWERS(Continued)
NOTES
Man
ual o
n w
eb -[
06/0
3]
Supplement - 2 g Casework Design SeriesPage 8 of 30
285
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
224 230 231File Drawers w/ Full File Drawers w/ Full File Drawers w/ Full
Extension Slides and File Extension Slides and File Extension Slides and FileFollower or Hanging System Follower or Hanging System Follower or Hanging System
220 222 223Open, Two Drawers Two Drawers File Drawers w/ Full
Extension Slides and FileFollower or Hanging System
210 211 212Open, Single Drawer Single Drawer
240 242 250Top Drawer Divided into Three File Drawers w/ Full Top Drawer Divided into Three
Equal Spaces Left to Right Extension Slides and File Equal Spaces Left to RightFollower or Hanging System
200 SERIES, BASE CABINETS with DRAWERS
Man
ual o
n w
eb -[
06/0
3]
Supplement - 2 g Casework Design SeriesPage 9 of 30
286
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
200 SERIES, BASE CABINETS with DRAWERS
251 252 253File Drawers w/ Full
Extension Slides and FileFollower or Hanging System
271 272 290Drawer Apron
261 262 270Top Drawer Divided into Three
Equal Spaces Left to Right
254 255 260File Drawers w/ Full Top Drawer Divided into Three
Extension Slides and File Equal Spaces Left to RightFollower or Hanging System
Man
ual o
n w
eb -[
06/0
3]
Supplement - 2 g Casework Design SeriesPage 10 of f 30
287
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
200 SERIES, BASE CABINETS with DRAWERS(Continued)
291 292Drawer Apron Drawer Apron
NOTES
Man
ual o
n w
eb -[
06/0
3]
Supplement - 2 g Casework Design SeriesPage 11 of 302
288
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
300 SERIES, WALL HUNG CABINET
300 301 302Open
306 307 3083/4" Sliding Doors 1/4" Glass Sliding Doors Angle Corner
309 310 311Blind Corner Open
312 3163/4" Sliding Doors
Man
ual o
n w
eb -[
06/0
3]
Supplement - 2 g Casework Design SeriesPage 12 of 30
289
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
300 SERIES, WALL HUNG CABINET(Continued)
317 318 3201/4" Glass Sliding Doors 1/4" Glass Sliding Doors & Open
1/4" Glass Back w/ Removable Stops
321 322 3233/4" Glass S & R Door
324 325 3263/4" Glass S & R Doors 3/4" Sliding Glass S & R Doors Partial Open
336 340 3413/4" Sliding Doors Cubicles Cubicles
(Open back)
Man
ual o
n w
eb -[
06/0
3]
Supplement - 2 g Casework Design SeriesPage 13 of 30
290
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
300 SERIES, WALL HUNG CABINET(Continued)
342 343 350Cubicles Cubicles Mail Boxes w/
(Open back) 1/4" Shelves
351 352 353Mail Boxes w/ Mail Boxes w/ Mail Boxes w/1/4" Shelves 1/4" Shelves 1/4" Shelves(Open back) (Open back)
Man
ual o
n w
eb -[
06/0
3]
Supplement - 2 g Casework Design SeriesPage 14 of 30
291
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
400 SERIES, TALL STORAGE CABINETS
410 411 412
406 407 4083/4" Sliding Doors 1/4" Sliding Glass Doors 3/4" S & R Glass Doors
400 401 402
Man
ual o
n w
eb -[
06/0
3]
Supplement - 2 g Casework Design SeriesPage 15 of 30
292
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
400 SERIES, TALL STORAGE CABINETS(Continued)
413 414 4163/4" S & R Glass Doors 3/4" S & R Glass Doors 3/4" Sliding Doors
417 418 4191/4" Sliding Glass Doors 3/4" S & R Glass Doors 3/4" Sliding
S & R Glass Doors
420 421 422
Man
ual o
n w
eb -[
06/0
3]
Supplement - 2 g Casework Design SeriesPage 16 of 30
293
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
400 SERIES, TALL STORAGE CABINETS(Continued)
430 431 432
426 427 429Dust Panel 1/4" Sliding Glass Doors Display Hutch w/
Integral or Separate Fixed Angled Shelves
423 424 425Split Height Split Height Apron Storage
Pull Out Hooks
Man
ual o
n w
eb -[
06/0
3]
Supplement - 2 g Casework Design SeriesPage 17 of 30
294
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
400 SERIES, TALL STORAGE CABINETS(Continued)
434 435 438Split Height Holds 56 Tote Trays 3/4" S & R Glass Doors
However Tote Trays are NIC
439 440 441Hutch, holds 32 Tote Trays Open Hutch Hutch
Tote Trays are NIC
443 444 445Hutch Drawing Board Storage Hutch w/ Open Cubicles Hutch w/ 3/4" Sliding Doors
Man
ual o
n w
eb -[
06/0
3]
400 SERIES, TALL STORAGE CABINETS(Continued)
446 447 448Hutch Hutch Hutch
3/4" Sliding Doors 1/4" Sliding Glass Doors 3/4" S & R Glass Doors
449 454 459Hutch Oven Cabinet Ceramic Drying Storage
3/4" S & R Sliding Glass Doors Adjustable Metal FrameW/ Galvanized Wire Mesh
Supplement - 2 g Casework Design SeriesPage 18 of 30
295
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
460 Presentation Panel Surrounds 461 Audio Visual Center
460-aTop Facia Panel
460-bEnd Panel
Right or Left Hand
Retracting DoorsFixed Shelf for TVw/ VCR/DVD Below
Man
ual o
n w
eb -[
06/0
3]
296
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
Supplement - 2 g Casework Design SeriesPage 19 of 30
500 SERIES, WARDROBE CABINETSMIRRORS TO BE FRAMED 12" X 14" X 1/4" PLATE, WITH PIN TRAY
500 501 502Open Wardrobe Teachers Wardrobe w/ Student Wardrobe
Shelf & Pole Lock, Shelf, Pole & Mirror Shelf & Pole
510 511 512Open Wardrobe Split Unit, Shelves / Wardrobe Dual Wardrobe
Shelf & Pole w/ Shelf, Pole, Mirror & Lock Shelf, Pole, Mirror & Lock
520 522 530Triple Open Wardrobe Wardrobe & Cubicles Wardrobe & Shelving
Shelf & Pole Shelves, Pole, Mirror & Lock Shelves, Pole, Mirror & Lock
Man
ual o
n w
eb -[
06/0
3]
297
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
500 SERIES, WARDROBE CABINETS(Continued)
MIRRORS TO BE FRAMED 12" X 14" X 1/4" PLATE, WITH PIN TRAY
531 532 533Teacher Center w/ Lock Teacher Center w/ Lock Teacher Center w/ Lock,Shelves, Pole & Mirror Shelves, Pole & Mirror Slide Out Tilting Paper2 Legal File Drawers 2 Legal File Drawers & 1/4" Dividers Shelves*, Paper Roller &
2 Legal File Drawers
540Hanging Wardrobe
Shelf & Pole
534 541 552Teacher Center w/ Lock, Double Hanging Wardrobe Student WardrobeSlide Out Tilting Paper Shelf & Pole w/ 15 Wall Hooks, Shelves,Shelves*, Paper Roller Ceiling Hooks or Pole
& Misc. Drawers
* See Slide Out Tilting Paper Shelf details on next page in this Supplement 2
Supplement - 2 g Casework Design SeriesPage 20 of 30
NOTE: Drawers in cabinets 531-533 shall be spaced away from cabinet ends up to 1” to allow for proper functionality when doorsare in the ninety degree open position.
Man
ual o
n w
eb -[
06/0
3]
298
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
Supplement - 2 g Casework Design SeriesPage 21 of 30
TYPICAL SLIDE OUT/TILTING PAPER SHELF DETAILS
PAPER TRAYGUIDE
CLEAT STOPBOTTOM OF DRAWER
PAPER TRAY
PAPER TRAYGUIDE
5 1/
4"5
1/4"
5 1/
2"
DOWEL STOP
5 1/
4"5
1/4"
5 1/
2"
17 7
/8"
SNUG FITTING3/8"Ø HARDWOODDOWEL STOP
TRAY ON OPENPOSITION
3/4" HARDWOODGUIDES
TRAY @ CLOSEDPOSITION
30º
1/2"3/4"
3/4"
1/2"
1 1/
2"
1/2" MELAMINESIDES & BACK
4 1/2"1/4" MELAMINEBAFFLE
3/4" MELAMINEBOTTOM
24"
2 1/
2"
FINGER PULL
Paper Tray Guide SystemFront View
Paper Tray Guide SystemSide View
Paper Tray - Front View
Paper Tray - Side View
Man
ual o
n w
eb -[
06/0
3]
299
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
600 SERIES, LIBRARY CABINETSSEE PAGE 21 OF THIS SUPPLEMENT FOR 600 SERIES NOTES
600 w/ or 605 w/o Back 601 w/ or 606 w/o Back 602 w/ or 607 w/o Back42" in Height including Top 60-1/2" Height including Top 72", 80" or 84" Height
620 w/ or 625 w/o Back 621 w/ or 626 w/o Back 622 w/ or 627 w/o Back42" in Height including Top 60-1/2" Height including Top 72", 80" or 84" Height
Back Same as Front Back Same as Front Back Same as Front
614 624 634Library of Congress Shelf Newspaper Rack Display Shelf
Hardwood Dowels
UNITS 614, 624 and 634 ARE INSERTS FOR THE ABOVE BOOK CASES
Supplement - 2 g Casework Design SeriesPage 22 of 30
Side View Side View
Man
ual o
n w
eb -[
06/0
3]
300
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
Supplement - 2 g Casework Design SeriesPage 23 of 30
600 SERIES, LIBRARY CABINETS(Continued)
651 654 664Book Cart, Fits 641 Base w/ Doors Base w/ 3/4" Sliding Doors
w/ Casters
640 641 644Charge Desk w/ Foot Rest, Book Return Open Base
Locked & Divided Top Drawerw/ Cash Tray
671-a w/o Lateral Bracing 672 673671-b w/ Lateral Bracing Table Gate
Table
674 681 682 or 692 w/ 18" LegsBase w/ Drawer Desk Magazine Rack
Man
ual o
n w
eb -[
06/0
3]
301
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
683Corner
600 SERIES, LIBRARY CABINETS(Continued)
684Base w/ File Drawers on
Full Extension Slides w/ FileFollower or Hanging System
693Dictionary Stand w/
Swivel Base
66227" High Base for
Card Files
652Slide Shelf, 2-5/8" High
663Card File, 15-3/4" High
653Card File, 10-3/4" High
643Card Files, 5-3/4" High
642Top
CARD FILE SYSTEM
NOTESAll Finished Backs in Panels or Continuous Lengths.Kick Spaces Front, Back & at Exposed Ends Typical.Card File System for 3" x 5" cards with built in follower.
Supplement - 2 g Casework Design SeriesPage 24 of 30
Man
ual o
n w
eb -[
06/0
3]
302
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
2
1
Supplement - 2 g Casework Design SeriesPage 25 of 30
700 SERIES, MOVEABLE CABINETSNOTE: All moveable units to be equipped with adequate WIC-approved casters for the intended load capacity.
SEE PAGE 1 OF THIS SUPPLEMENT FOR ADDITIONAL 700 SERIES NOTES
Unit 707Shall be 30" Deep w/
Top Drawer in 3 Sections36" in Height = 6 Drawers
33" or 30" = 5 Drawers27" or 24" = 4 Drawers
Storage & Drawers Storage w/ 3/4" Sliding Doors Open Wardrobe715 716 720
Open Storage Storage w/ Doors Storage & Drawers710 712 714
Base w/ One Side Base w/ Paper Drawers704 707
Open Base Base w/ Doors Base w/ Two Sides700 702 703
of Cubicles Double Wheel Swivel Casters
Diaphragm bottom required Of Cubicles
Tilting Shelf details on page 298 Diaphragm bottom required
Diaphragm bottom required
Man
ual o
n w
eb -[
06/0
3]
303
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
730 731 732Bookcase, Single Sided Bookcase, 2 Sided Bookcase, 2 Sided
Fixed Tapered Legs
700 SERIES, MOVEABLE CABINETS(Continued)
NOTE: All moveable units to be equipped with adequate approved casters for the intended load capacity.
725 726Teachers Cabinet Teachers Cabinet
w/ Lock 3/4" Sliding Doors & Lock729
Toy CartMetal angle reinforced corners required
728Toy Cart
Metal angle reinforced corners required
721Open Wardrobe
Two Sides
722Wardrobe w / Doors
724Teachers Cabinet
w / File Drawers & LockDiaphragm bottom required
Supplement - 2 g Casework Design SeriesPage 26 of 30
Man
ual o
n w
eb -[
06/0
3]
304
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
Supplement - 2 g Casework Design SeriesPage 27 of 30
700 SERIES, MOVEABLE CABINETS(Continued)
NOTE: All moveable units to be equipped with adequate approved casters for the intended load capacity.
742 (See notes)Demonstration Cart
48" x 33" x 24"Laboratory Top
737 738 739Block Cart Block Cart Ball & Bat Cart w/ 5 Equal
Metal angle reinforced Metal angle reinforced Compartments at One Endcorners required corners required Metal angle reinforced
corners required
734 735 736Bookcase, 2 Sided Clay Cart Clay Cart w/ Custom 22 ga.
Trash Can NIC Galvanized Liner, 3/4" LP TopMetal angle reinforced corners required 8 ea. 1/4" Hardboard Panels
Metal angle reinforced corners required
NOTES FOR CABINET 742:
To be furnished with 6” round chemical sink, Burrett Rods, cross bar andflush sockets, galley pump with polyethylene tubing and 1 gallon bottlesfor both fresh water and waste, 3 prong duplex outlet with 15’ supply cord,locks on all doors and drawers, 6 pegs on back of storage compartmentdoor and 1/4” pegboard liner on back of sink door.
Man
ual o
n w
eb -[
06/0
3]
305
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
747 750 751Nature Demonstration Cart Open Hutch Cabinet Hutch Cabinet
48" x 33" x 24" Diaphragm bottom required W/ 3/4" Sliding Doors3/4" Sliding Doors & LP Top Diaphragm bottom required
Removable 22ga. Galvanized PanDiaphragm bottom required
743 7442 Sided Easel Cart Single Sided Easel Cart
48" x 54" x 24" 48" x 66" x 24" w/ Side DoorTack Board Top, LP Face & Top Tack Board Top, LP Face
Diaphragm bottom required Diaphragm bottom required
700 SERIES, MOVEABLE CABINETS(Continued)
NOTE: All moveable units to be equipped with adequate approved casters for the intended load capacity.
746 (See notes)Cooking Demonstration Cart
48" x 33" x 24"3/4" Sliding Doors & LP TopDiaphragm bottom required
NOTES FOR CABINET 746:
To be furnished with electric cooking and mixing units,built in 3 prong electric service w/ 15’ supply cord.
Supplement - 2 g Casework Design SeriesPage 28 of 30
Man
ual o
n w
eb -[
06/0
3]
306
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
Supplement - 2 g Casework Design SeriesPage 29 of 30
700 SERIES, MOVEABLE CABINETS(Continued)
NOTE: All moveable units to be equipped with adequate approved casters for the intended load capacity.
752 753 754Open Hutch Cabinet Hutch Cabinet Open Hutch Cabinet
W/ 3/4" Sliding Doors
755Hutch Cabinet
W/ 3/4" Sliding Doors
TYPICAL DIAPHRAGM BOTTOM DETAIL
Man
ual o
n w
eb -[
06/0
3]
307
NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.
Woodwork InstituteManual of Millwork - 5/1/03
as updated at http://www.woodworkinstitute.com/manual.asp
700 SERIES, MOVEABLE CABINETS(Continued)
NOTE: All moveable units to be equipped with adequate approved casters for the intended load capacity.
STUDY CARRELS, LAYOUT & CONSTRUCTION
761 763 764
762 765
760Study Carrel
38" x 54" x 30"
KEY DETAIL “B” DETAIL “C”
Supplement - 2 g Casework Design SeriesPage 30 of 30
Man
ual o
n w
eb -[
06/0
3]
308
NOTESM
anua
l on
web
-[06
/03]