SUPPLEMENT 2TO

SECTIONS 14 & 15

DESIGN SERIESELEVATIONS

assurance.

Man

ual o

n w

eb -[

06/0

3]

Supplement - 2 g Casework Design SeriesPage 1 of 30

278

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

SUPPLEMENT - 2CABINET DESIGN SERIES - CDS

THE FOLLOWING CASEWORK ILLUSTRATIONS ARE ADOPTED AS DESIGN STANDARDS ANDPROVIDED TO ASSIST ARCHITECT / DESIGN PROFESSIONALS AND CASEWORK USERS INSELECTING TYPICAL DESIGNS. THESE ILLUSTRATIONS ARE NOT INTENDED TO LIMIT ORRESTRICT CREATIVITY, OR BE ALL INCLUSIVE.

In utilizing the CDS numbering system, it is not necessary to show casework elevations in your architecturaldrawings. However, it is necessary to show a plan view with each CDS number indicated along with thewidth, height, and depth in inches (Example: “102-36x30x18”). Cabinet dimensions indicate the nominaloutside dimension (floor to top of countertop for height and face of finished wall to face of cabinet door fordepth). Fabricators are permitted a tolerance of 1/2” plus/minus in width only.

If other designs are desired than those provided for in the CDS system, they may be indicated by selectingthe CDS number most closely representing the desired design, followed by the letter "M" and a descriptionor illustration of the design modification. (Example: "102M - 2 shelves - 36x30x18" or "102M - no shelves -36x30x18"). If the CDS numbering system is used in conjunction with cabinet elevations on architecturaldrawings, the cabinet elevations shall govern on any conflict between the requirements of the elevationand/or the CDS number.

The following casework heights are recommended for various school grades, subject to ADA requirements:

Kindergarten - Grade 1 = 24"Grades 2 - 3 = 27"Grades 4 - 6 = 30"Grades 7 - 9 = 33"Grades 10 and above = 36"

The CABINET DESIGN SERIES are subdivided as follows:

Base Cabinets w/o Drawers = 100 SeriesBase Cabinets w/ Drawers = 200 SeriesWall Hung Cabinets = 300 SeriesTall Storage Cabinets = 400 SeriesTall Wardrobe Cabinets = 500 SeriesLibrary Cabinets = 600 SeriesMoveable Cabinets = 700 Series

ALL HARDWARE AND ACCESSORIES SHALL BE AS APPROVED BY THESE STANDARDS ANDLISTED IN THE INSTITUTE’S SEPARATELY PUBLISHED "APPROVED HARDWARE SUPPLEMENT"

WHICH IS UPDATED ANNUALLY.

GENERAL NOTES: 1. 100 or 200 Series cabinets may be converted into moveable cabinets by prefixing a “7” to the number.2. Moveable cabinets shall be equipped with adequate approved casters for the intended load capacity.3. Cabinet Design Series #'s 728, 729, 735, 736, 737, 738, 739 require metal angle reinforced corners.4. Carts and rolling tall storage cabinets with doors, lacking any horizontal and/or vertical stabilizing

dividers, require a diaphragm bottom; specifically Cabinet Design Series #'s 702, 712, 716, 722, 743,744, 746, 747, 750, and 751.

Man

ual o

n w

eb -[

06/0

3]

Supplement - 2 g Casework Design SeriesPage 2 of 30

279

100 SERIES, BASE CABINETS w/o DRAWERS

117 120 1211/4" Sliding Glass Doors Open

111 112 1163/4" Sliding Doors

with Vertical Divider

106 107 1103/4" Sliding Doors 1/4" Sliding Glass Doors Open

without Vertical Divider

100 101 102Open

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

Man

ual o

n w

eb -[

06/0

3]

Supplement - 2 g Casework Design SeriesPage 3 of 30

280

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

100 SERIES, BASE CABINETS w/o DRAWERS(Continued)

148 150 151Removable Back / Sink Sink / 6" Apron Sink / 6" Apron4" Apron Behind Doors

141 142 146Removable Back / Sink Removable Back / Sink Removable Back / Sink4" Apron Behind Door 4" Apron Behind Doors 3/4" Sliding Doors

4" Apron Behind Doors

132 136 1403/4" Sliding Doors Open / Sink

Removable Back4" Apron

122 130 131

Man

ual o

n w

eb -[

06/0

3]

Supplement - 2 g Casework Design SeriesPage 4 of 30

281

100 SERIES, BASE CABINETS w/o DRAWERS(Continued)

155a 156 157Section Detail of Removable Back Removable Back

No Base Sink / 6" Apron Sink / 6" Apron

154 154a 155ADA Sink w/ Partial 8" Base Section Detail of ADA Sink w/ Out Base

Partial 8" Deep Base

152 153 153aSink / 6" Apron ADA Sink Section Detail of

Removable Base / Toe Removable Base / ToeSupported on Clips

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

hh

158ADA Removeable Cabinet Front, Base

and Heigth Adjustable Countertop

NOTES FOR CABINET 158:

Cabinet doors and sink apron mounted to a removable(for ADA compliance) frame, secured to adjoining wall orcabinets to the left and right.

Base removable for ADA compliance.

Countertop to be self contained with side mounting cleatswhich can be used to secure it at standard and ADA com-pliant height requirements.

Ends of adjoining countertops and cabinets shall be flushand considered finished ends.

Man

ual o

n w

eb -[

06/0

3]

Supplement - 2 g Casework Design SeriesPage 5 of 302

282

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

100 SERIES, BASE CABINETS w/o DRAWERS(Continued)

179 180 182Retractable Towel Rack Open

176 177 178Blind Corner Range Tray Storage

1/4" Dividers

170 171 172Open

160 161 162Cart Storage Cart Storage Cart Storage

Hardwood Side Guides Hardwood Side Guides Hardwood Side Guides

Man

ual o

n w

eb -[

06/0

3]

Supplement - 2 g Casework Design SeriesPage 6 of 30

283

100 SERIES, BASE CABINETS w/o DRAWERS(Continued)

189 190 191Drawing Board Rack Storage Apron Storage Apron

192 193 194Storage Apron Countertop Support Countertop Support

Floor & Wall Mounted Floor & Wall Mounted

186 187 188Corner Sliding Tray & Sliding Trays

Lift Up Shelf

195 196 197Countertop Support Corner / Lazy Susan Corner / Lazy Susan

Wall Mounted

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

Man

ual o

n w

eb -[

06/0

3]

Supplement - 2 g Casework Design SeriesPage 7 of 30

284

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

198 199Ceramics Drying Ceramics Drying

Includes Adjustable Metal Frame Includes Sliding Metal FrameShelves w/ Galvanized Wire Mesh Shelves w/ Galvanized Wire Mesh

100 SERIES, BASE CABINETS w/o DRAWERS(Continued)

NOTES

Man

ual o

n w

eb -[

06/0

3]

Supplement - 2 g Casework Design SeriesPage 8 of 30

285

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

224 230 231File Drawers w/ Full File Drawers w/ Full File Drawers w/ Full

Extension Slides and File Extension Slides and File Extension Slides and FileFollower or Hanging System Follower or Hanging System Follower or Hanging System

220 222 223Open, Two Drawers Two Drawers File Drawers w/ Full

Extension Slides and FileFollower or Hanging System

210 211 212Open, Single Drawer Single Drawer

240 242 250Top Drawer Divided into Three File Drawers w/ Full Top Drawer Divided into Three

Equal Spaces Left to Right Extension Slides and File Equal Spaces Left to RightFollower or Hanging System

200 SERIES, BASE CABINETS with DRAWERS

Man

ual o

n w

eb -[

06/0

3]

Supplement - 2 g Casework Design SeriesPage 9 of 30

286

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

200 SERIES, BASE CABINETS with DRAWERS

251 252 253File Drawers w/ Full

Extension Slides and FileFollower or Hanging System

271 272 290Drawer Apron

261 262 270Top Drawer Divided into Three

Equal Spaces Left to Right

254 255 260File Drawers w/ Full Top Drawer Divided into Three

Extension Slides and File Equal Spaces Left to RightFollower or Hanging System

Man

ual o

n w

eb -[

06/0

3]

Supplement - 2 g Casework Design SeriesPage 10 of f 30

287

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

200 SERIES, BASE CABINETS with DRAWERS(Continued)

291 292Drawer Apron Drawer Apron

NOTES

Man

ual o

n w

eb -[

06/0

3]

Supplement - 2 g Casework Design SeriesPage 11 of 302

288

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

300 SERIES, WALL HUNG CABINET

300 301 302Open

306 307 3083/4" Sliding Doors 1/4" Glass Sliding Doors Angle Corner

309 310 311Blind Corner Open

312 3163/4" Sliding Doors

Man

ual o

n w

eb -[

06/0

3]

Supplement - 2 g Casework Design SeriesPage 12 of 30

289

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

300 SERIES, WALL HUNG CABINET(Continued)

317 318 3201/4" Glass Sliding Doors 1/4" Glass Sliding Doors & Open

1/4" Glass Back w/ Removable Stops

321 322 3233/4" Glass S & R Door

324 325 3263/4" Glass S & R Doors 3/4" Sliding Glass S & R Doors Partial Open

336 340 3413/4" Sliding Doors Cubicles Cubicles

(Open back)

Man

ual o

n w

eb -[

06/0

3]

Supplement - 2 g Casework Design SeriesPage 13 of 30

290

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

300 SERIES, WALL HUNG CABINET(Continued)

342 343 350Cubicles Cubicles Mail Boxes w/

(Open back) 1/4" Shelves

351 352 353Mail Boxes w/ Mail Boxes w/ Mail Boxes w/1/4" Shelves 1/4" Shelves 1/4" Shelves(Open back) (Open back)

Man

ual o

n w

eb -[

06/0

3]

Supplement - 2 g Casework Design SeriesPage 14 of 30

291

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

400 SERIES, TALL STORAGE CABINETS

410 411 412

406 407 4083/4" Sliding Doors 1/4" Sliding Glass Doors 3/4" S & R Glass Doors

400 401 402

Man

ual o

n w

eb -[

06/0

3]

Supplement - 2 g Casework Design SeriesPage 15 of 30

292

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

400 SERIES, TALL STORAGE CABINETS(Continued)

413 414 4163/4" S & R Glass Doors 3/4" S & R Glass Doors 3/4" Sliding Doors

417 418 4191/4" Sliding Glass Doors 3/4" S & R Glass Doors 3/4" Sliding

S & R Glass Doors

420 421 422

Man

ual o

n w

eb -[

06/0

3]

Supplement - 2 g Casework Design SeriesPage 16 of 30

293

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

400 SERIES, TALL STORAGE CABINETS(Continued)

430 431 432

426 427 429Dust Panel 1/4" Sliding Glass Doors Display Hutch w/

Integral or Separate Fixed Angled Shelves

423 424 425Split Height Split Height Apron Storage

Pull Out Hooks

Man

ual o

n w

eb -[

06/0

3]

Supplement - 2 g Casework Design SeriesPage 17 of 30

294

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

400 SERIES, TALL STORAGE CABINETS(Continued)

434 435 438Split Height Holds 56 Tote Trays 3/4" S & R Glass Doors

However Tote Trays are NIC

439 440 441Hutch, holds 32 Tote Trays Open Hutch Hutch

Tote Trays are NIC

443 444 445Hutch Drawing Board Storage Hutch w/ Open Cubicles Hutch w/ 3/4" Sliding Doors

Man

ual o

n w

eb -[

06/0

3]

400 SERIES, TALL STORAGE CABINETS(Continued)

446 447 448Hutch Hutch Hutch

3/4" Sliding Doors 1/4" Sliding Glass Doors 3/4" S & R Glass Doors

449 454 459Hutch Oven Cabinet Ceramic Drying Storage

3/4" S & R Sliding Glass Doors Adjustable Metal FrameW/ Galvanized Wire Mesh

Supplement - 2 g Casework Design SeriesPage 18 of 30

295

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

460 Presentation Panel Surrounds 461 Audio Visual Center

460-aTop Facia Panel

460-bEnd Panel

Right or Left Hand

Retracting DoorsFixed Shelf for TVw/ VCR/DVD Below

Man

ual o

n w

eb -[

06/0

3]

296

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

Supplement - 2 g Casework Design SeriesPage 19 of 30

500 SERIES, WARDROBE CABINETSMIRRORS TO BE FRAMED 12" X 14" X 1/4" PLATE, WITH PIN TRAY

500 501 502Open Wardrobe Teachers Wardrobe w/ Student Wardrobe

Shelf & Pole Lock, Shelf, Pole & Mirror Shelf & Pole

510 511 512Open Wardrobe Split Unit, Shelves / Wardrobe Dual Wardrobe

Shelf & Pole w/ Shelf, Pole, Mirror & Lock Shelf, Pole, Mirror & Lock

520 522 530Triple Open Wardrobe Wardrobe & Cubicles Wardrobe & Shelving

Shelf & Pole Shelves, Pole, Mirror & Lock Shelves, Pole, Mirror & Lock

Man

ual o

n w

eb -[

06/0

3]

297

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

500 SERIES, WARDROBE CABINETS(Continued)

MIRRORS TO BE FRAMED 12" X 14" X 1/4" PLATE, WITH PIN TRAY

531 532 533Teacher Center w/ Lock Teacher Center w/ Lock Teacher Center w/ Lock,Shelves, Pole & Mirror Shelves, Pole & Mirror Slide Out Tilting Paper2 Legal File Drawers 2 Legal File Drawers & 1/4" Dividers Shelves*, Paper Roller &

2 Legal File Drawers

540Hanging Wardrobe

Shelf & Pole

534 541 552Teacher Center w/ Lock, Double Hanging Wardrobe Student WardrobeSlide Out Tilting Paper Shelf & Pole w/ 15 Wall Hooks, Shelves,Shelves*, Paper Roller Ceiling Hooks or Pole

& Misc. Drawers

* See Slide Out Tilting Paper Shelf details on next page in this Supplement 2

Supplement - 2 g Casework Design SeriesPage 20 of 30

NOTE: Drawers in cabinets 531-533 shall be spaced away from cabinet ends up to 1” to allow for proper functionality when doorsare in the ninety degree open position.

Man

ual o

n w

eb -[

06/0

3]

298

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

Supplement - 2 g Casework Design SeriesPage 21 of 30

TYPICAL SLIDE OUT/TILTING PAPER SHELF DETAILS

PAPER TRAYGUIDE

CLEAT STOPBOTTOM OF DRAWER

PAPER TRAY

PAPER TRAYGUIDE

5 1/

4"5

1/4"

5 1/

2"

DOWEL STOP

5 1/

4"5

1/4"

5 1/

2"

17 7

/8"

SNUG FITTING3/8"Ø HARDWOODDOWEL STOP

TRAY ON OPENPOSITION

3/4" HARDWOODGUIDES

TRAY @ CLOSEDPOSITION

30º

1/2"3/4"

3/4"

1/2"

1 1/

2"

1/2" MELAMINESIDES & BACK

4 1/2"1/4" MELAMINEBAFFLE

3/4" MELAMINEBOTTOM

24"

2 1/

2"

FINGER PULL

Paper Tray Guide SystemFront View

Paper Tray Guide SystemSide View

Paper Tray - Front View

Paper Tray - Side View

Man

ual o

n w

eb -[

06/0

3]

299

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

600 SERIES, LIBRARY CABINETSSEE PAGE 21 OF THIS SUPPLEMENT FOR 600 SERIES NOTES

600 w/ or 605 w/o Back 601 w/ or 606 w/o Back 602 w/ or 607 w/o Back42" in Height including Top 60-1/2" Height including Top 72", 80" or 84" Height

620 w/ or 625 w/o Back 621 w/ or 626 w/o Back 622 w/ or 627 w/o Back42" in Height including Top 60-1/2" Height including Top 72", 80" or 84" Height

Back Same as Front Back Same as Front Back Same as Front

614 624 634Library of Congress Shelf Newspaper Rack Display Shelf

Hardwood Dowels

UNITS 614, 624 and 634 ARE INSERTS FOR THE ABOVE BOOK CASES

Supplement - 2 g Casework Design SeriesPage 22 of 30

Side View Side View

Man

ual o

n w

eb -[

06/0

3]

300

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

Supplement - 2 g Casework Design SeriesPage 23 of 30

600 SERIES, LIBRARY CABINETS(Continued)

651 654 664Book Cart, Fits 641 Base w/ Doors Base w/ 3/4" Sliding Doors

w/ Casters

640 641 644Charge Desk w/ Foot Rest, Book Return Open Base

Locked & Divided Top Drawerw/ Cash Tray

671-a w/o Lateral Bracing 672 673671-b w/ Lateral Bracing Table Gate

Table

674 681 682 or 692 w/ 18" LegsBase w/ Drawer Desk Magazine Rack

Man

ual o

n w

eb -[

06/0

3]

301

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

683Corner

600 SERIES, LIBRARY CABINETS(Continued)

684Base w/ File Drawers on

Full Extension Slides w/ FileFollower or Hanging System

693Dictionary Stand w/

Swivel Base

66227" High Base for

Card Files

652Slide Shelf, 2-5/8" High

663Card File, 15-3/4" High

653Card File, 10-3/4" High

643Card Files, 5-3/4" High

642Top

CARD FILE SYSTEM

NOTESAll Finished Backs in Panels or Continuous Lengths.Kick Spaces Front, Back & at Exposed Ends Typical.Card File System for 3" x 5" cards with built in follower.

Supplement - 2 g Casework Design SeriesPage 24 of 30

Man

ual o

n w

eb -[

06/0

3]

302

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

2

1

Supplement - 2 g Casework Design SeriesPage 25 of 30

700 SERIES, MOVEABLE CABINETSNOTE: All moveable units to be equipped with adequate WIC-approved casters for the intended load capacity.

SEE PAGE 1 OF THIS SUPPLEMENT FOR ADDITIONAL 700 SERIES NOTES

Unit 707Shall be 30" Deep w/

Top Drawer in 3 Sections36" in Height = 6 Drawers

33" or 30" = 5 Drawers27" or 24" = 4 Drawers

Storage & Drawers Storage w/ 3/4" Sliding Doors Open Wardrobe715 716 720

Open Storage Storage w/ Doors Storage & Drawers710 712 714

Base w/ One Side Base w/ Paper Drawers704 707

Open Base Base w/ Doors Base w/ Two Sides700 702 703

of Cubicles Double Wheel Swivel Casters

Diaphragm bottom required Of Cubicles

Tilting Shelf details on page 298 Diaphragm bottom required

Diaphragm bottom required

Man

ual o

n w

eb -[

06/0

3]

303

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

730 731 732Bookcase, Single Sided Bookcase, 2 Sided Bookcase, 2 Sided

Fixed Tapered Legs

700 SERIES, MOVEABLE CABINETS(Continued)

NOTE: All moveable units to be equipped with adequate approved casters for the intended load capacity.

725 726Teachers Cabinet Teachers Cabinet

w/ Lock 3/4" Sliding Doors & Lock729

Toy CartMetal angle reinforced corners required

728Toy Cart

Metal angle reinforced corners required

721Open Wardrobe

Two Sides

722Wardrobe w / Doors

724Teachers Cabinet

w / File Drawers & LockDiaphragm bottom required

Supplement - 2 g Casework Design SeriesPage 26 of 30

Man

ual o

n w

eb -[

06/0

3]

304

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

Supplement - 2 g Casework Design SeriesPage 27 of 30

700 SERIES, MOVEABLE CABINETS(Continued)

NOTE: All moveable units to be equipped with adequate approved casters for the intended load capacity.

742 (See notes)Demonstration Cart

48" x 33" x 24"Laboratory Top

737 738 739Block Cart Block Cart Ball & Bat Cart w/ 5 Equal

Metal angle reinforced Metal angle reinforced Compartments at One Endcorners required corners required Metal angle reinforced

corners required

734 735 736Bookcase, 2 Sided Clay Cart Clay Cart w/ Custom 22 ga.

Trash Can NIC Galvanized Liner, 3/4" LP TopMetal angle reinforced corners required 8 ea. 1/4" Hardboard Panels

Metal angle reinforced corners required

NOTES FOR CABINET 742:

To be furnished with 6” round chemical sink, Burrett Rods, cross bar andflush sockets, galley pump with polyethylene tubing and 1 gallon bottlesfor both fresh water and waste, 3 prong duplex outlet with 15’ supply cord,locks on all doors and drawers, 6 pegs on back of storage compartmentdoor and 1/4” pegboard liner on back of sink door.

Man

ual o

n w

eb -[

06/0

3]

305

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

747 750 751Nature Demonstration Cart Open Hutch Cabinet Hutch Cabinet

48" x 33" x 24" Diaphragm bottom required W/ 3/4" Sliding Doors3/4" Sliding Doors & LP Top Diaphragm bottom required

Removable 22ga. Galvanized PanDiaphragm bottom required

743 7442 Sided Easel Cart Single Sided Easel Cart

48" x 54" x 24" 48" x 66" x 24" w/ Side DoorTack Board Top, LP Face & Top Tack Board Top, LP Face

Diaphragm bottom required Diaphragm bottom required

700 SERIES, MOVEABLE CABINETS(Continued)

NOTE: All moveable units to be equipped with adequate approved casters for the intended load capacity.

746 (See notes)Cooking Demonstration Cart

48" x 33" x 24"3/4" Sliding Doors & LP TopDiaphragm bottom required

NOTES FOR CABINET 746:

To be furnished with electric cooking and mixing units,built in 3 prong electric service w/ 15’ supply cord.

Supplement - 2 g Casework Design SeriesPage 28 of 30

Man

ual o

n w

eb -[

06/0

3]

306

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

Supplement - 2 g Casework Design SeriesPage 29 of 30

700 SERIES, MOVEABLE CABINETS(Continued)

NOTE: All moveable units to be equipped with adequate approved casters for the intended load capacity.

752 753 754Open Hutch Cabinet Hutch Cabinet Open Hutch Cabinet

W/ 3/4" Sliding Doors

755Hutch Cabinet

W/ 3/4" Sliding Doors

TYPICAL DIAPHRAGM BOTTOM DETAIL

Man

ual o

n w

eb -[

06/0

3]

307

NOTE: These drawings are available as Autodesk7 Revit7 Families and AutoCAD “.DWG” and “.DXF” filesat http://www.woodworkinstitute.com/manual.asp or with our CD Rom version of the MANUAL.

Woodwork InstituteManual of Millwork - 5/1/03

as updated at http://www.woodworkinstitute.com/manual.asp

700 SERIES, MOVEABLE CABINETS(Continued)

NOTE: All moveable units to be equipped with adequate approved casters for the intended load capacity.

STUDY CARRELS, LAYOUT & CONSTRUCTION

761 763 764

762 765

760Study Carrel

38" x 54" x 30"

KEY DETAIL “B” DETAIL “C”

Supplement - 2 g Casework Design SeriesPage 30 of 30

Man

ual o

n w

eb -[

06/0

3]

308

NOTESM

anua

l on

web

-[06

/03]