ZXWR RNC (V3.09.30) Radio Network Controller Radio Configuration Operation Guide

ZXWR RNCRadio Network Controller

Radio Configuration Operation Guide

Version: 3.09.30

ZTE CORPORATIONNO. 55, Hi-tech Road South, ShenZhen, P.R.ChinaPostcode: 518057Tel: +86-755-26771900Fax: +86-755-26770801URL: http://ensupport.zte.com.cnE-mail: [email protected]

LEGAL INFORMATIONCopyright © 2011 ZTE CORPORATION.

The contents of this document are protected by copyright laws and international treaties. Any reproduction or

distribution of this document or any portion of this document, in any form by any means, without the prior written

consent of ZTE CORPORATION is prohibited. Additionally, the contents of this document are protected by

contractual confidentiality obligations.

All company, brand and product names are trade or service marks, or registered trade or service marks, of ZTE

CORPORATION or of their respective owners.

This document is provided “as is”, and all express, implied, or statutory warranties, representations or conditions

are disclaimed, including without limitation any implied warranty of merchantability, fitness for a particular purpose,

title or non-infringement. ZTE CORPORATION and its licensors shall not be liable for damages resulting from the

use of or reliance on the information contained herein.

ZTE CORPORATION or its licensors may have current or pending intellectual property rights or applications

covering the subject matter of this document. Except as expressly provided in any written license between ZTE

CORPORATION and its licensee, the user of this document shall not acquire any license to the subject matter

herein.

ZTE CORPORATION reserves the right to upgrade or make technical change to this product without further notice.

Users may visit ZTE technical support website http://ensupport.zte.com.cn to inquire related information.

The ultimate right to interpret this product resides in ZTE CORPORATION.

Revision History

Revision No. Revision Date Revision Reason

R3.0 2011-08-31 Third Edition (3.09.30.12)

The following sections have been modified:

1. Preface

R2.0 2011-02-28 Second Edition (3.09.30.09)

The following sections have been modified:

1. Preface

2. 1.2.2 Modifying Advanced Parameters on [RNC Radio

Resource Management] Interface

3. 1.6.2 Modifying Advanced Parameters on [UTRAN Cell]

Interface

4. 1.7.2 Modifying Advanced Parameters on [GSM Neighbouring

Cell] Interface

5. 2.2 Starting Template Manager

R1.1 2010-09-01 1. 1.2.1:The section Creating RNC Radio Resource

Management is updated.

2. 1.6.1:The section Creating UTRAN Cell is updated.

R1.0 2010-07-05 First Edition (V3.09.30.03)

Serial Number: SJ-20100603155704-019

Publishing Date: 2011-08-31

ContentsAbout This Manual ......................................................................................... I

Chapter 1 RNC Radio Resource Management Static DataConfiguration.......................................................................................... 1-11.1 Overview ........................................................................................................... 1-1

1.2 RNC Radio Resource Management..................................................................... 1-4

1.2.1 Creating RNC Radio Resource Management ............................................. 1-4

1.2.2 Modifying Advanced Parameters on [RNC Radio Resource Management]Interface................................................................................................. 1-9

1.2.3 Deleting RNC Radio Resource Management............................................ 1-27

1.3 Node B Configuration Information...................................................................... 1-29

1.3.1 Creating Node B Configuration Information .............................................. 1-29

1.3.2 Modifying Advanced Parameters on Node B Configuration InformationInterface............................................................................................... 1-30

1.3.3 Batch Modifying Node B Configuration Information ................................... 1-32

1.4 External UTRAN Cell ........................................................................................ 1-38

1.4.1 Creating External UTRAN Cell ................................................................ 1-38

1.4.2 Modifying Advanced Parameters on External UTRAN Cell Interface .......... 1-40

1.5 External GSM Cell............................................................................................ 1-42

1.5.1 Creating External GSM Cell .................................................................... 1-42

1.5.2 Modifying Advanced Parameters on External GSM Cell Interface .............. 1-44

1.6 UTRAN Cell ..................................................................................................... 1-45

1.6.1 Creating UTRAN Cell ............................................................................. 1-45

1.6.2 Modifying Advanced Parameters on [UTRAN Cell] Interface ..................... 1-49

1.7 GSM Neighbouring Cell .................................................................................... 1-64

1.7.1 Creating GSM Neighbouring Cell............................................................. 1-64

1.7.2 Modifying Advanced Parameters on [GSM Neighbouring Cell] Interface ..... 1-66

1.8 Neighbouring Cell............................................................................................. 1-68

1.8.1 Creating Neighbouring Cell ..................................................................... 1-68

1.8.2 Modifying Advanced Parameters on Neighbouring Cell Interface ............... 1-70

1.9 Cell Selection and Reselection .......................................................................... 1-71

1.9.1 Creating Cell Selection and Reselection .................................................. 1-71

1.9.2 Modifying Advanced Parameters on Cell Selection and ReselectionInterface............................................................................................... 1-73

1.10 UTRAN Cell Information in MBMS Service Area ............................................... 1-74

I

1.10.1 Creating UTRAN Cell Information in MBMS Service Area........................ 1-74

1.10.2 Modifying UTRAN Cell Information in MBMS Service Area...................... 1-76

1.11 Creating User Authorized PLMN+SNAC Information ......................................... 1-77

1.12 Creating LAC and SNAC Information ............................................................... 1-79

Chapter 2 Template Manager..................................................................... 2-12.1 Overview ........................................................................................................... 2-1

2.2 Starting Template Manager ................................................................................. 2-2

2.3 Creating Template .............................................................................................. 2-3

2.4 Modifying Template Attributes ............................................................................. 2-5

2.5 Modifying Template Description Information ......................................................... 2-7

2.6 Exporting Template............................................................................................. 2-8

2.7 Importing Template............................................................................................. 2-9

2.8 Deleting Template ............................................................................................ 2-10

2.9 Compare Templates ..........................................................................................2-11

2.10 Applying Template .......................................................................................... 2-13

Figures............................................................................................................. I

Tables ...........................................................................................................VII

Glossary ........................................................................................................IX

II

About This ManualPurpose

This manual introduces the ZXWR RNC radio resource configuration to implement thebasic service functions.

What Is in This Manual

This manual contains the following chapters:

Chapter Summary

Chapter 1, RNC Radio Resource Management

Static Data Configuration

Describes ZXWR RNC radio resource manage-

ment and node creation/modification.

Chapter 2, Template Manager Describes the operations in the templatemanager.

Intended Audience

This document is intended for the engineers and maintenance personnel who know aboutthe RNC hardware structure, and radio parameter indexes.

Reference

l ZXWR RNC (V3.09.30) Radio Network Controller Configuration Tool Operation Guidel ZXWR RNC (V3.09.30.03) Radio Network Controller Dynamic Data Management

Operation Guidel ZXWR RNC (V3.09.30) Radio Network Controller Radio Parameter Referencel ZXWR RNC (V3.09.30.03) Radio Network Controller Ground Configuration Operation

Guide

I

II

Chapter 1RNC Radio ResourceManagement Static DataConfigurationTable of Contents

Overview....................................................................................................................1-1RNC Radio Resource Management ...........................................................................1-4Node B Configuration Information.............................................................................1-29External UTRAN Cell................................................................................................1-38External GSM Cell....................................................................................................1-42UTRAN Cell .............................................................................................................1-45GSM Neighbouring Cell............................................................................................1-64Neighbouring Cell.....................................................................................................1-68Cell Selection and Reselection .................................................................................1-71UTRAN Cell Information in MBMS Service Area.......................................................1-74Creating User Authorized PLMN+SNAC Information ................................................1-77Creating LAC and SNAC Information........................................................................1-79

1.1 OverviewUnder one UTRAN, one ZXWR RNC can be configured with several series of data (that is,RNC Config Set). Each series of data has one unique ID. Each series of complete ZXWRRNC configuration data includes Ground resource data and radio resource data.

Before configuring the radio resource data, make sure that the Ground resource data hasbeen configured.

For details of ground resource data configurations, refer to ZXWR RNC (V3.09.30) RadioNetwork Controller Ground Configuration Reference.

ZXWR RNC The operations of the radio resource configurations are shown in Table 1-1.

1-1

SJ-20100603155704-019|2011-08-31 ZTE Proprietary and Confidential

ZXWR RNC Radio Configuration Operation Guide

Table 1-1 Operations about ZXWR RNC Radio Resource Configurations

Operations

S.N. MO

Create Modify Delete Query Others

1

RNC radio

resource

manage-

ment

√ √ √ √

Modify

advanced

parameters.

2

Node B con-

figuration in-

formation

√ √ √ √

Iub interface

reset.

Modify

advanced

parameters.

3

GSM Cell

Configura-

tion

√ √ √ √

Modify

advanced

parameters.

4 UTRAN cell √ √ √ √

Modify

advanced

parameters.

5Neighbor

Cell√ √ √ √

Cell reset.

Modify

advanced

parameters.

6

GSM

Neighbor

Cell

√ √ √ √

Modify

advanced

parameters.

7

Cell

selection

and

re-selection

√ √ √ √

Modify

advanced

parameters.

8MBMS

UTRAN cell√ √ √ √

Modify

advanced

parameters.

9

HNODEB

Cell

Resource

√ √ √ √

Modify

advanced

parameters.

10

User Autho-

rized PLM-

N+SNAC

Information

√ √ √ √ None

1-2


Chapter 1 RNC Radio Resource Management Static Data Configuration

Operations

S.N. MO

Create Modify Delete Query Others

11

LAC and

SNAC

Information

√ √ √ √ None

12QoS Con-

figuration√ √ None √ None

The flow of ZXWR RNC radio resource configurations is as shown in Figure 1-1.

Figure 1-1 Flow of ZXWR RNC Radio Resource Configurations

As shown in Figure 1-1, the procedure to create ZXWR RNC radio resource managementnodes is from up down, while the procedure to delete is from down up. That is, during thecreation, the sub-node can be created only when the father node has been created, andthe father node can be deleted only when the sub-node has been deleted.

1-3



Note:

Users must obtain the mutex right before operating the NM system software. For themethod to apply for the mutex right, refer to ZXWR RNC (V3.09.30) Radio NetworkController Configurations Tool Operation Guide.

1.2 RNC Radio Resource Management

1.2.1 Creating RNC Radio Resource Management

Short Description

To create ZXWR RNC global radio parameters.

Prerequisites

1. UTRAN Subnetwork has been created.2. RNC Managed Element has been created.3. RNC Config Set has been created.4. RNC Ground Resource Management has been created.5. RNC Local Office whose ANI is 0 has been created.

Steps

1. On Configuration Resource Tree, right-click RNC Config Set and choose Create >RNC Radio Resource Management, as shown in Figure 1-2.

Figure 1-2 Creating RNC Radio Resource Management

2. The RNC Configuration Information dialog box pops up, as shown in Figure 1-3 toFigure 1-9.

1-4



Figure 1-3 RNC Configuration Information Dialog Box (Basic Information Tab)

Figure 1-4 RNC Configuration Information Dialog Box (RPLMN Range InformationTab)

1-5



Figure 1-5 RNC Configuration Information Dialog Box (CN NAS ConfigurationInformation Tab)

Figure 1-6 RNC Configuration Information Dialog Box (RCP Scrambling CodeConfiguration Information Tab)

1-6



Figure 1-7 RNC Configuration Information Dialog Box (RNC ConfigurationSupplement Parameters Tab)

Figure 1-8 RNC Configuration Information Dialog Box (Other Parameters Tab)

1-7



Figure 1-9 RNC Configuration Information Dialog Box (Advanced Parameter Tab)

3. Fill in the parameters and click OK. The system creates RNC Radio ResourceManagement.

– End of Steps –

Result

RNC Radio Resource Management and its sub-nodes have been added inConfiguration Resource Tree on the left pane of RNC Radio Resource Managementinterface, as shown in Figure 1-10.

Figure 1-10 Result of Creating RNC Radio Resource Management

1-8



1.2.2 Modifying Advanced Parameters on [RNC Radio ResourceManagement] Interface

Abstract

Modifying Advanced Parameter Configurations on RNC Radio Resource ManagementInterface

In RNC Radio Resource Management.Advanced Parameter Manager page, configurethe advanced parameters that you have right to modify.

Prerequisites

RNC Radio Resource Management has been created.

Steps

1. Double-click RNC Radio Resource Management to open the property configuration

page. Click the icon, as shown in Figure 1-11.

Figure 1-11 Modifying Advanced Parameter

2. The Advanced Parameter Manager page pops up. The tabs in this page are shownin Figure 1-12 to Figure 1-41.

1-9



Figure 1-12 Advanced Parameter Manager.UE Timers and Constants Information

Figure 1-13 Advanced Parameter Manager.UE Internal Measurement Configuration

1-10



Figure 1-14 Advanced Parameter Manager.Transport Format Combination Set ofSCCPCH

Figure 1-15 Advanced Parameter Manager.Limiting HSDPA GBR ResourceConsumption Information

1-11



Figure 1-16 Advanced Parameter Manager.UE DTX/DRX Configuration Information

Figure 1-17 Advanced Parameter Manager.Power Control Related to Service andDiversity Mode

1-12



Figure 1-18 Advanced Parameter Manager.UE Intra-frequency MeasurementConfiguration

Figure 1-19 Advanced Parameter Manager.UE Inter-Rat measurement ConfigurationInformation

1-13



Figure 1-20 Advanced Parameter Manager.Dynamic Radio Bearer ControlInformation

Figure 1-21 Advanced Parameter Manager.CFN Offset Configuration Information

1-14



Figure 1-22 Advanced Parameter Manager.RNC Configuration SupplementInformation

Figure 1-23 Advanced Parameter Manager.Service Basic Configuration Information

1-15



Figure 1-24 Advanced Parameter Manager.FACH Traffic Control Information

Figure 1-25 Advanced Parameter Manager.UE Inter-frequency MeasurementConfiguration

1-16



Figure 1-26 Advanced Parameter Manager.UE Inter-Rat Measurement Relativeto Traffic Category

Figure 1-27 Advanced Parameter Manager.MBMS Configuration Information

1-17



Figure 1-28 Advanced Parameter Manager.Transport Format Set

Figure 1-29 Advanced Parameter Manager.RNC Radio Resource Management

1-18



Figure 1-30 Advanced Parameter Manager.Iu Interface and Constants Information

Figure 1-31 Advanced Parameter Manager.Service Physical Layer ConfigurationInformation

1-19



Figure 1-32 Advanced Parameter Manager.CN System Information

Figure 1-33 Advanced Parameter Manager.HSPA Configuration Information

1-20



Figure 1-34 Advanced Parameter Manager.UE Inter-frequency MeasurementRelative to Traffic Category

Figure 1-35 Advanced Parameter Manager.Transport Format Combination Set ofPRACH

1-21



Figure 1-36 Advanced Parameter Manager.Global Access Control

Figure 1-37 Advanced Parameter Manager.Traffic-Related Power Control

1-22



Figure 1-38 Advanced Parameter Manager.UE Intra-frequency MeasurementRelative to Traffic Category Configuration Information

Figure 1-39 Advanced Parameter Manager.E-DCH Reference ConfigurationInformation

1-23



Figure 1-40 Advanced Parameter Manager.UE Traffic Volume MeasurementConfiguration

Figure 1-41 Advanced Parameter Manager.NodeB Common MeasurementConfiguration

1-24



Click Add button to add parameter information on the current tab. Under this state,the newly-added parameters are not saved into the database.

Select a piece of parameter information and click Delete button. If the selectedparameter information has not been saved to the database, it can be deleted directlyfrom the tab.

If the selected parameter information has been saved to the database, the deletioncan be cancelled by clicking Undelete button.

3. Modify the target parameters.

Take the parameter in line 7 on the Advanced Parameter Manager.UE TrafficVolume Measurement Configuration as an example.

a. In Advanced Parameter Manager.UE Traffic Volume MeasurementConfiguration, double-click line 7 and a dialog box pops up, as shown in Figure1-42.

Figure 1-42 MODIFYING ADVANCED PARAMETER 1

b. Double-click the target parameter. A dialog box pops up, as shown in Figure 1-43.

1-25




c. Double-click an item, and you can select a value from the drop-down list, as shownin Figure 1-44.


d. Click OK after the modification and the system returns to the AdvancedParameter Manager.UE Traffic Volume Measurement Configuration dialogbox.

1-26



Note:

The method to modify the parameters in this manual are the same as the abovedescriptions (steps a-d). It will not be mentioned in the upcoming chapters.

4. Click Apply to save the settings on all tabs but not to exit the current dialog box. Orclick OK to save the settings on all tabs and exit the current dialog box.


Follow-Up Action

The shortcut menu on the RNC Radio Resource Management tab is as shown in Table1-2.

Table 1-2 SHORTCUT MENU ON RNC RADIO RESOURCE MANAGEMENT TAB

Shortcut Menu Description

Modify

Cancel

Save

Close

Close All

Help

Modify Advanced Parameter

1.2.3 Deleting RNC Radio Resource Management

Short Description

To delete RNC Radio Resource Management and its subnodes.

Prerequisites

1. UTRAN Subnetwork has been created.2. RNC Managed Element has been created.3. RNC Config Set has been created.4. RNC Ground Resource Management has been created.5. RNC Radio Resource Management has been created.

1-27



Steps

1. On Configuration Resource Tree, right-click RNC Radio Resource Management,and select Delete, as shown in Figure 1-45.

Figure 1-45 Deleting RNC Radio Resource Management

2. The Information dialog box for deleting RNC radio resource management pops up,as shown in Figure 1-46.

Figure 1-46 Information Dialog Box for Deleting RNC Radio Resource Management

3. Enter the verify code and click OK. The system deletes the whole subtree of RNCRadio Resource Management.

1-28



Note:

The method to delete parameters contained in this manual are the same as above. Itwill not be described repeatedly hereinafter.


1.3 Node B Configuration Information

1.3.1 Creating Node B Configuration Information

Prerequisites1. UTRAN Subnetwork has been created2. RNC Managed Element has been created.3. RNC Config Set has been created.4. RNC Ground Resource Management has been created.5. RNC Radio Resource Management has been created.6. Related Node B office has been created.

Steps1. On Configuration Resource Tree, right-click Node B Configuration Information

and choose Create > Node B Configuration Information, as shown in Figure 1-47.

Figure 1-47 Creating Node B Configuration Information

2. TheNode B Configuration Information dialog box pops up, as shown in Figure 1-48.

1-29



Figure 1-48 Node B Configuration Information Dialog Box

If Create Continually is checked, the system does not exit from the current dialog boxafter creating a piece of Node B configuration information successfully.

If Create Continually is not checked, the system automatically exits from the currentdialog box after creating a piece of Node B configuration information successfully.

Note:

All Create Continually options in NMS have the same function as above. They willnot be described repeatedly hereinafter.

3. Click OK and the system creates Node B Configuration Information.


1.3.2 Modifying Advanced Parameters on Node B ConfigurationInformation Interface

Prerequisites

Node B Configuration Information has been created.

Steps

1. Double-click to open the Node B Configuration Information tab. Click on thetoolbar, as shown in Figure 1-49.

1-30




2. The Advanced Parameter Manager dialog box pops up, as shown in Figure 1-50.

Figure 1-50 Advanced Parameter Manager Dialog Box (Node B ConfigurationInformation)

3. Double-click the parameter to be modified. After the modification, click Apply to savethe settings on all tabs but not to exit the current dialog box, or click OK to save thesettings on all tabs and exit the current dialog box.


Example

The shortcut menu on the Node B Configuration Information tab is as shown in Table1-3.

Table 1-3 Shortcut Menu on Node B Configuration Information Tab


Modify

Cancel

Save

1-31




Batch Modify

Batch Save

Close

Close All

Help

Iub Interface Reset


Note:

For operations about the button in the shortcut menu, refer to ZXWR RNC (V3.09.30)Radio Network Controller Dynamic Data Management Operation Guide.

1.3.3 Batch Modifying Node B Configuration Information

Prerequisites


Steps

1. Double-click to open the Node B Configuration Information tab. Click , as shownin Figure 1-51.

Figure 1-51 Selecting Batch Modify

2. The Select Batch Modify Object tab pops up, as shown in Figure 1-52.

1-32



Figure 1-52 Select Batch Modify Objects Tab

a. Click at the end of the Root MO field and the Please select root objectinterface pops up, as shown in Figure 1-53.

Figure 1-53 Please Select Root Object Interface

b. Select the target node and click OK. All Node B Configuration Informationsubnodes under this node become objects to be modified in batches.

c. Click at the end of Other Filter(s) to filter the objects and the Add Filterinterface pops up, as shown in Figure 1-54.

1-33



Figure 1-54 Add Filter Interface

Right-click on the blank area and select Add from the shortcut menu, as shown inFigure 1-55.

Figure 1-55 Selecting Add

An information column is added into the Add Filter interface, as shown in Figure1-56.

1-34



Figure 1-56 Newly-added Information Column on Add Filter Interface

Double-click the newly-added information column to select/fill in the filteringcondition, as shown in Figure 1-57, Figure 1-58, and Figure 1-59.

Figure 1-57 Selecting Filtering Condition 1

1-35



Figure 1-58 Selecting Filtering Condition 2

Figure 1-59 Filling in Filtering Condition

Click OK after selecting and filling in filtering conditions.

3. All Node B Configuration Information subnodes that meet the filtering conditionsunder the target node are displayed in the Query Result pane.

1-36



Figure 1-60 Query Result

Tick an object in the Query Result pane and it can be saved after the modification.

4. Click the NodeB Configuration Information tab, as shown in Figure 1-61.

Figure 1-61 NodeB Configuration Information Tab

5. Fill in/modify the parameters on the Node B Configuration Information tab, and thenclick . All attributes of Node B Configuration Information subnodes in the QueryResult pane on the Select Batch Modify Objects tab are saved.

Note:

The method to modify RNC Radio Resource Management subnodes in batches areall the same as above. It will not be described repeatedly hereinafter.


1-37



1.4 External UTRAN Cell

1.4.1 Creating External UTRAN Cell

Prerequisites

1. UTRAN Subnetwork has been created.2. RNC Managed Element has been created.3. RNC Config Set has been created.4. RNC Ground Resource Management has been created.5. RNC Radio Resource Management has been created.6. Adjacent RNC Office has been created. For how to create Adjacent RNC Office,

refer to ZXWR RNC (V3.09.30) Radio Network Controller Ground ConfigurationOperation Guide.

Steps

1. On Configuration Resource Tree, right-click External UTRAN Cell and chooseCreate > External UTRAN Cell, as shown in Figure 1-62.

Figure 1-62 Creating External UTRAN Cell

2. The External UTRAN Cell dialog box pops up, as shown in Figure 1-63, Figure 1-64,Figure 1-65 and Figure 1-66.

1-38



Figure 1-63 External UTRAN Cell Dialog Box (Global Information Tab)

Figure 1-64 External UTRAN Cell Dialog Box (Global Else Tab)

1-39



Figure 1-65 External UTRAN Cell Dialog Box (LCS Tab)

Figure 1-66 External UTRAN Cell Dialog Box (Antenna Tab)

3. Click OK and the system creates External UTRAN Cell.


1.4.2 Modifying Advanced Parameters on External UTRAN CellInterface

Prerequisites

External UTRAN Cell has been created.

1-40



Steps

1. Double-click to open the External UTRANCell tab. Click on the toolbar, as shownin Figure 1-67.



Figure 1-68 Advanced Parameter Manager Dialog Box (External UTRAN Cell)



ExampleThe shortcut menu on the External UTRAN Cell tab is as shown in Table 1-4.

Table 1-4 Shortcut Menu on External UTRAN Cell Tab


Modify

Cancel

1-41




Save

Batch Modify

Batch Save

Close

Close All

Help


1.5 External GSM Cell

1.5.1 Creating External GSM Cell

Prerequisites


Steps

1. On Configuration Resource Tree, right-click External GSM Cell and choose Create> External GSM Cell, as shown in Figure 1-69.

1-42



Figure 1-69 Creating External GSM Cell

2. The External GSM Cell dialog box pops up, as shown in Figure 1-70.

Figure 1-70 External GSM Cell Dialog Box

3. Fill in the parameters and click OK. The system creates GSM Cell Configuration.


1-43



1.5.2 Modifying Advanced Parameters on External GSM CellInterface

PrerequisitesExternal GSM Cell has been created.

Steps

1. Double-click to open the External GSM Cell tab. Click on the toolbar, as shownin Figure 1-71.



Figure 1-72 Advanced Parameter Manager Dialog Box



ExampleThe shortcut menu on the External GSM Cell interface is as shown in Table 1-5.

1-44



Table 1-5 Shortcut Menu on External GSM Cell Interface


Modify

Cancel

Save

Batch Modify

Batch Save

Close

Close All

Help


1.6 UTRAN Cell

1.6.1 Creating UTRAN Cell

Prerequisites

UTRAN Subnetwork has been created.

RNC Managed Element has been created.

RNC Config Set has been created.

RNC Ground Resource Management has been created.

RNC Radio Resource Management has been created.


Steps

1. On Configuration Resource Tree, right-click UTRAN Cell and choose Create >UTRAN Cell, as shown in Figure 1-73.

1-45



Figure 1-73 Creating UTRAN Cell

2. The Business UTRAN Cell dialog box pops up, as shown in Figure 1-74 to Figure1-79.

Figure 1-74 Business UTRAN Cell Dialog Box (UTRAN Cell Global Information Tab)

1-46



Figure 1-75 Business UTRAN Cell Dialog Box (Cell Setup Parameters Tab)

Figure 1-76 Business UTRAN Cell Dialog Box (LCS and Cell Antenna Tab)

1-47



Figure 1-77 Business UTRAN Cell Dialog Box (Cell Ability and Cell Reselection Tab)

Figure 1-78 Business UTRAN Cell Dialog Box (OCNS Parameter Tab)

1-48



Figure 1-79 Business UTRAN Cell Dialog Box (Status Info Tab)

3. Click OK and the system creates UTRAN Cell.


1.6.2 Modifying Advanced Parameters on [UTRAN Cell] Interface

Abstract

Modifying Advanced Parameters on UTRAN Cell Interface

Prerequisites

UTRAN Cell has been created.

Steps

1. Double-click UTRAN Cell to open the property configuration page. Click the iconon the toolbar, as shown in Figure 1-80.


2. A dialog box pops up, as shown in Figure 1-81 - Figure 1-93.

1-49



Figure 1-81 Advanced Parameter Manager.MBMS Configuration Information in aCell

Figure 1-82 Advanced Parameter Manager.Load Control Relationship

1-50



Figure 1-83 Advanced Parameter Manager.SCPICH

Figure 1-84 Advanced Parameter Manager.Balance Information

1-51



Figure 1-85 Advanced Parameter Manager.PCPICH

Figure 1-86 Advanced Parameter Manager.FACH

1-52



Figure 1-87 Advanced Parameter Manager.UE Traffic Volume MeasurementConfiguration Information in a Cell

Figure 1-88 Advanced Parameter Manager.SCCPCH

1-53



Figure 1-89 Advanced Parameter Manager.MICH

Figure 1-90 Advanced Parameter Manager.NodeB Common MeasurementConfiguration Information in a Cell

1-54



Figure 1-91 Advanced Parameter Manager.PRACH

Figure 1-92 Advanced Parameter Manager.PCH

1-55



Figure 1-93 Advanced Parameter Manager.UE Measurement Configuration inSystem Information Block

Figure 1-94 Advanced Parameter Manager.UTRAN Cell

1-56



Figure 1-95 Advanced Parameter Manager.UE Internal Measurement ConfigurationInformation in a Cell

Figure 1-96 Advanced Parameter Manager.PSCH

1-57



Figure 1-97 Advanced Parameter Manager.PICH

Figure 1-98 Advanced Parameter Manager.RACH

1-58



Figure 1-99 Advanced Parameter Manager.AICH

Figure 1-100 Advanced Parameter Manager.HSPA Configuration Information in aCell

1-59



Figure 1-101 Advanced Parameter Manager.Cell-Related Access Control

Figure 1-102 Advanced Parameter Manager.SSCH

1-60



Figure 1-103 Advanced Parameter Manager.Cell Enhanced FACH

Figure 1-104 Advanced Parameter Manager.PCCPCH

1-61



Figure 1-105 Advanced Parameter Manager.BCH

Figure 1-106 Advanced Parameter Manager.HS-PDSCH Measurement Power Offset

1-62



Figure 1-107 Advanced Parameter Manager.Power Control not Related to Service

3. Double-click the parameter to be modified. After the modification, click Apply to savethe settings on all tabs but not to exit the current dialog box. Or click OK to save thesettings on all tabs and exit the current dialog box.


Follow-Up Action

The shortcut menu on the UTRAN Cell tab is shown in Table 1-6.

Table 1-6 SHORTCUT MENU ON UTRAN CELL TAB


Modify

Cancel

Save

Batch Modify

Batch Save

Close

Close All

1-63




Help

Cell Reset

Spy

UnSpy

Get Status


Note:

For how to operate , , and in the shortcut menu, refer to ZXWRRNC (V3.09.30)Radio Network Controller Dynamic Data Management Operation Guide.

1.7 GSM Neighbouring Cell

1.7.1 Creating GSM Neighbouring Cell

Short Description

If there is any GSM neighbouring cell in a UTRAN cell, it is required to create GSMNeighbouring Cell.

Prerequisites

1. UTRAN Subnetwork has been created.2. RNC Managed Element has been created.3. RNC Config Set has been created.4. RNC Ground Resource Management has been created.5. RNC Radio Resource Management has been created.6. UTRAN Cell has been created.7. External GSM Cell has been created.

Steps

1. On Configuration Resource Tree, right-click GSM Neighbouring Cell and chooseCreate > GSM Neighbouring Cell, as shown in Figure 1-108.

1-64



Figure 1-108 Creating GSM Neighbouring Cell

2. The GSM Neighbouring Cell dialog box pops up, as shown in Figure 1-109.

Figure 1-109 GSM Neighbouring Cell Dialog Box

1-65



3. Fill in the parameters and click OK. The system creates GSM Neighboring Cell.


1.7.2 Modifying Advanced Parameters on [GSM Neighbouring Cell]Interface

Abstract

Modifying Advanced Parameters on GSM Neighbouring Cell Interface

Prerequisites

GSM Neighbouring Cell Cell has been created.

Steps

1. Double-click GSM Neighbouring Cell to open the property configuration page. Clickthe icon on the toolbar, as shown in Figure 1-110.


2. A dialog box pops up, as shown in Figure 1-111.

1-66




3. Double-click the parameter to be modified. After the modification, click Apply to savethe settings on all tabs but not to exit the current dialog box. Or click OK to save thesettings on all tabs and exit the current dialog box.


Follow-Up ActionThe shortcut menu on the GSM Neighbouring Cell tab is shown in Table 1-7.

Table 1-7 SHORTCUT MENU ON GSM NEIGHBOURING CELL INTERFACE


Modify

Cancel

Save

Batch Modify

Batch Save

Close

Close All

Help

1-67





1.8 Neighbouring Cell

1.8.1 Creating Neighbouring Cell

Short Description

To create Neighbouring Cell in the system (here, the system is WCDMA).

Prerequisites

1. UTRAN Subnetwork has been created.2. RNC Managed Element has been created.3. RNC Config Set has been created.4. RNC Ground Resource Management has been created.5. RNC Radio Resource Management has been created.6. UTRAN Cell has been created.7. UTRAN External Cell has been created.

Steps

1. On Configuration Resource Tree, right-click Neighbouring Cell and choose Create> Neighbouring Cell, as shown in Figure 1-112.

1-68



Figure 1-112 Creating Neighbouring Cell

2. The Neighbouring Cell dialog box pops up, as shown in Figure 1-113.

Figure 1-113 Neighbouring Cell Dialog Box

3. Fill in the parameters and click OK. The system creates Neighbouring Cell.


1-69



1.8.2 Modifying Advanced Parameters on Neighbouring CellInterface

PrerequisitesNeighbouring Cell has been created.

Steps

1. Double-click to open the Neighboring Cell tab. Click on the toolbar, as shown inFigure 1-114.






ExampleThe shortcut menu on the Neighbouring Cell interface is as shown in Table 1-8.

1-70



Table 1-8 Shortcut Menu on Neighbouring Cell Interface


Modify

Cancel

Save

Batch Modify

Batch Save

Close

Close All

Help


1.9 Cell Selection and Reselection

1.9.1 Creating Cell Selection and Reselection

Prerequisites

1. UTRAN Subnetwork has been created.2. RNC Managed Element has been created.3. RNC Config Set has been created.4. RNC Ground Resource Management has been created.5. RNC Radio Resource Management has been created.6. UTRAN Cell has been created.

Steps

1. On Configuration Resource Tree, right-click Cell Selection and Reselection andchoose Create > Cell Selection and Cell Reselection, as shown in Figure 1-116.

1-71



Figure 1-116 Creating Cell Selection and Cell Reselection

2. The Cell Selection and Cell Reselection dialog box pops up, as shown in Figure1-117.

Figure 1-117 Cell Selection and Cell Reselection Dialog Box

3. Fill in the parameters and click OK. The system creates Cell selection andReselection.


1-72



1.9.2 Modifying Advanced Parameters on Cell Selection andReselection Interface

Prerequisites

Cell Selection and Reselection has been created.

Steps

1. Double-click to open theCell Selection andReselection tab. Click on the toolbar,as shown in Figure 1-118.






1-73



ExampleThe shortcut menu on the Cell Selection and Reselection interface is as shown in Table1-9.

Table 1-9 Shortcut Menu on Cell Selection and Reselection Interface


Modify

Cancel

Save

Batch Modify

Batch Save

Close

Close All

Help


1.10 UTRAN Cell Information in MBMS Service Area

1.10.1 Creating UTRAN Cell Information in MBMS Service Area

Prerequisites

1. UTRAN Subnetwork has been created.2. RNC Managed Element has been created.3. RNC Config Set has been created.4. RNC Ground Resource Management has been created.5. RNC Radio Resource Management has been created.6. UTRAN Cell has been created.

Note:

DUARFCN and FreBandInd in Cell Setup Parameters in the cell list under the samefrequency layer of the same MBMS must be the same. In addition, they must be the sameas DUARFCN and FreBandInd in the table. MbmsSuptInd in the corresponding CellAbility and Cell Reselection must be 1 Supporting both MBMS and non-MBMS orOnly Supporting MBMS.

1-74



Steps

1. On Configuration Resource Tree, right-click UTRAN Cell Information in MBMSService Area and chooseCreate > UTRANCell Information inMBMSService Area,as shown in Figure 1-120.

Figure 1-120 Creating UTRAN Cell Information in MBMS Service Area

2. The UTRAN Cell Information in MBMS Service Area dialog box pops up, as shownin Figure 1-121.

Figure 1-121 UTRAN Cell Information in MBMS Service Area Dialog Box

3. Click OK and the system creates UTRAN Cell Information in MBMS Service Area.


1-75



1.10.2 Modifying UTRAN Cell Information in MBMS Service Area

PrerequisitesUTRAN Cell Information in MBMS Service Area has been created.

Steps1. Double-click to open the UTRAN Cell Information in MBMS Service Area tab. Click

on the toolbar, as shown in Figure 1-122.






ExampleThe shortcut menu on the UTRAN Cell Information in MBMS Service Area interface isas shown in Table 1-10.

1-76



Table 1-10 Shortcut Menu on UTRAN Cell Information in MBMS Service Area Interface


Modify

Cancel

Save

Batch Modify

Batch Save

Close

Close All

Help


1.11 Creating User Authorized PLMN+SNACInformation

Prerequisites


Steps

1. On Configuration Resource Tree, right-click User Authorized PLMN+SNACInformation and choose Create > User Authorized PLMN+SNAC Information, asshown in Figure 1-124.

1-77



Figure 1-124 Creating User Authorized PLMN+SNAC Information

2. The User Authorized PLMN+SNAC Information dialog box pops up, as shown inFigure 1-125.

Figure 1-125 User Authorized PLMN+SNAC Information Dialog Box

3. Click OK and the system creates User Authorized PLMN+SNAC Information.


Example

The shortcut menu on the User Authorized PLMN+SNAC Information tab is as shownin Table 1-11.

1-78



Table 1-11 Shortcut Menu on User Authorized PLMN+SNAC Information Tab


Modify

Cancel

Save

Batch Modify

Batch Save

Close

Close All

Help

1.12 Creating LAC and SNAC InformationPrerequisites


Steps

1. On Configuration Resource Tree, right-click LAC and SNAC Information andchoose Create > LAC and SNAC Information, as shown in Figure 1-126.

1-79



Figure 1-126 Creating LAC and SNAC Information

2. The LAC and SNAC Information dialog box pops up, as shown in Figure 1-127.

Figure 1-127 LAC and SNAC Information Dialog Box

3. Click OK and the system creates LAC and SNAC Information.


Example

The shortcut menu on the LAC and SNAC Information interface is as shown in Table1-12.

1-80



Table 1-12 Shortcut Menu on LAC and SNAC Information Interface


Modify

Cancel

Save

Batch Modify

Batch Save

Close

Close All

Help

1-81



This page intentionally left blank.

1-82


Chapter 2Template ManagerTable of ContentsOverview....................................................................................................................2-1Starting Template Manager ........................................................................................2-2Creating Template ......................................................................................................2-3Modifying Template Attributes.....................................................................................2-5Modifying Template Description Information ...............................................................2-7Exporting Template.....................................................................................................2-8Importing Template.....................................................................................................2-9Deleting Template ....................................................................................................2-10Compare Templates .................................................................................................2-11Applying Template ....................................................................................................2-13

2.1 OverviewThe template manager is required when modifying the template parameters.

There can be several template instances and one default template instance under eachtemplate type.

In actual applications, it supports the functions of creating, deleting, saving, importing, andexporting the template, as well as the template comparison and template application.

The toolbar menu on the template manager is as shown in Table 2-1.

Table 2-1 Toolbar of Template Manager

Icon Description

To create the template.

To delete the template.

To save the template.

To modify information about the template.

To import the template.

To export the template.

To compare the templates.

To use the template parameters.

2-1



2.2 Starting Template ManagerPrerequisites

1. UTRAN Subnet has been created.2. RNC Managed Element has been created.3. RNC Config Set has been created.4. RNC Ground Resource Management has been created.5. RNC Radio Resource Management has been created.

Steps1. On the main menu, choose RNC Managed Element > Start Template Manager, as

shown in Figure 2-1.

Figure 2-1 Starting Template Manager

2. Click Starting Template Manager. The Input dialog box pops up, as shown in Figure2-2.

Figure 2-2 Input Dialog Box

3. Select the correct version and click OK. The Parameter Template Manager dialogbox pops up, as shown in Figure 2-3.

2-2


Chapter 2 Template Manager

Figure 2-3 Parameter Template Manager

The template types are displayed in the left pane. At present, there is one templateinstance under each template type by default. You can customize templates asrequired.


2.3 Creating TemplatePrerequisites


Steps

1. Select one template in the Parameter Template Manager dialog box and click onthe toolbar. The Input dialog box pops up, as shown in Figure 2-4. Fill in the templateID.

2-3




Alternatively, create a new template, as shown in Figure 2-5.

Figure 2-5 Creating a New Template

2. Click OK and the Input dialog box pops up, as shown in Figure 2-6. Fill in the ID ofthe created template.


3. Click OK and the Input dialog box pops up, as shown in Figure 2-7. Fill in thedescriptions for the created template.

2-4




4. Click OK, as shown in Figure 2-8. The system creates a new template.

Figure 2-8 Successfully Creating a New Template


2.4 Modifying Template AttributesPrerequisites


Steps1. On the template management tree in the left pane, click the created template and the

corresponding tab pops up in the right pane, as shown in Figure 2-9.

2-5



Figure 2-9 Selecting a Template

2. Double-click the target information on the tab and a dialog box pops up, as shown inFigure 2-10.

Figure 2-10 Template Information

3. Double-click the target information and it becomes editable, as shown in Figure 2-11.

2-6



Figure 2-11 Modifying Template Information

4. Modify the target information and click OK. The system returns to Figure 2-9.

5. Click to save the modifications on the template.


2.5 Modifying Template Description InformationPrerequisites


Steps

1. In the Parameter Template Manager dialog box, click and the Input dialog boxpops up, as shown in Figure 2-12. Fill in the modified information.

2-7




2. Click OK and the system modifies the template description.


2.6 Exporting TemplatePrerequisites1. UTRAN Subnetwork has been created.2. RNC Managed Element has been created.3. RNC Config Set has been created.4. RNC Ground Resource Management has been created.5. RNC Radio Resource Management has been created.

Steps

1. In the Parameter Template Manager dialog box, click , as shown in Figure 2-13.Fill in the file name to be exported.

Figure 2-13 Save Dialog Box

2. Click Save, and the Info dialog box pops up, as shown in Figure 2-14. Click OK.

2-8



Figure 2-14 Info Dialog Box


2.7 Importing TemplatePrerequisites1. UTRAN Subnetwork has been created.2. RNC Managed Element has been created.3. RNC Config Set has been created.4. RNC Ground Resource Management has been created.5. RNC Radio Resource Management has been created.

Steps1. On the template management tree in the left pane, double-click the template type

corresponding to the template, as shown in Figure 2-15.

Figure 2-15 Importing Parameter Template

2. Click and the Open dialog box pops up, as shown in Figure 2-16. Select the fileto be imported.

2-9



Figure 2-16 Open Dialog Box

3. Click Open and the Info dialog box pops up, as shown in Figure 2-17.

Figure 2-17 Info Dialog Box


2.8 Deleting TemplatePrerequisites


Steps

1. On the template management tree in the left pane, double-click the template instanceto be deleted. Right-click it and select Edit > Delete, as shown in Figure 2-18.

2-10



Figure 2-18 Deleting Template

Alternatively, select the template instance to be deleted on the template managementtree, and then click in the toolbar.

2. The Confirm dialog box pops up, as shown in Figure 2-19.

Figure 2-19 Confirm Dialog Box

3. Click OK and the system deletes the template.


2.9 Compare TemplatesPrerequisites


2-11



Steps

1. Click on the Parameter Template Manager interface and the TemplateComparison dialog box pops up, as shown in Figure 2-20.

Figure 2-20 Template Comparison Dialog Box 1

2. Select the template type in Select and select two templates to be compared inLeft/right Template. Click Template Compare and the comparison results pop up.The software automatically indicates the different properties, as shown in Figure 2-21.

2-12



Figure 2-21 Template Comparison Dialog Box 2

3. Click Return to close the Template Comparison dialog box.


2.10 Applying TemplatePrerequisites


Steps

1. In the Parameter Template Manager interface, click and the TemplateApplication dialog box pops up, as shown in Figure 2-22.

2-13



Figure 2-22 Template Application Dialog Box 1

2. Double-click the template value to be modified and select the template name to beused, as shown in Figure 2-23.

Figure 2-23 Template Application Dialog Box 2

2-14



3. Click Apply and the Info dialog box pops up, as shown in Figure 2-24. Select thesubnet.

Figure 2-24 Info Dialog Box (Select Subnet ID)

4. Click OK, and a dialog box pops up, as shown in Figure 2-25. Select the configurationset.

Figure 2-25 Info Dialog Box (Select Configuration Set ID)

5. Click OK and the Success dialog box pops up, as shown in Figure 2-26.

Figure 2-26 Success Dialog Box

6. Click OK and the system returns to the Template Application dialog box as shown inFigure 2-23.

7. On Figure 2-23, click Return to exit from the dialog box.


2-15



Result

After applying this template, advanced parameters of all objects that using this template inthis configuration set will be modified into the new template.

Note:

Except being modified by using the Apply template, advanced parameters can also bechanged by selecting the corresponding template through theModify button on the toolbar.

2-16


FiguresFigure 1-1 Flow of ZXWR RNC Radio Resource Configurations ............................... 1-3

Figure 1-2 Creating RNC Radio Resource Management........................................... 1-4

Figure 1-3 RNC Configuration Information Dialog Box (Basic InformationTab) ........................................................................................................ 1-5

Figure 1-4 RNC Configuration Information Dialog Box (RPLMN Range InformationTab) ........................................................................................................ 1-5

Figure 1-5 RNC Configuration Information Dialog Box (CN NAS ConfigurationInformation Tab)...................................................................................... 1-6

Figure 1-6 RNC Configuration Information Dialog Box (RCP Scrambling CodeConfiguration Information Tab) ................................................................ 1-6

Figure 1-7 RNC Configuration Information Dialog Box (RNC ConfigurationSupplement Parameters Tab).................................................................. 1-7

Figure 1-8 RNC Configuration Information Dialog Box (Other ParametersTab) ........................................................................................................ 1-7

Figure 1-9 RNC Configuration Information Dialog Box (Advanced ParameterTab) ........................................................................................................ 1-8

Figure 1-10 Result of Creating RNC Radio Resource Management .......................... 1-8

Figure 1-11 Modifying Advanced Parameter.............................................................. 1-9

Figure 1-12 Advanced Parameter Manager.UE Timers and ConstantsInformation............................................................................................ 1-10

Figure 1-13 Advanced Parameter Manager.UE Internal MeasurementConfiguration ........................................................................................ 1-10

Figure 1-14 Advanced Parameter Manager.Transport Format Combination Set ofSCCPCH .............................................................................................. 1-11

Figure 1-15 Advanced Parameter Manager.Limiting HSDPA GBR ResourceConsumption Information ...................................................................... 1-11

Figure 1-16 Advanced Parameter Manager.UE DTX/DRX ConfigurationInformation............................................................................................ 1-12

Figure 1-17 Advanced Parameter Manager.Power Control Related to Service andDiversity Mode...................................................................................... 1-12

Figure 1-18 Advanced Parameter Manager.UE Intra-frequency MeasurementConfiguration ........................................................................................ 1-13

Figure 1-19 Advanced Parameter Manager.UE Inter-Rat measurementConfiguration Information...................................................................... 1-13

I


Figure 1-20 Advanced Parameter Manager.Dynamic Radio Bearer ControlInformation............................................................................................ 1-14

Figure 1-21 Advanced Parameter Manager.CFN Offset ConfigurationInformation............................................................................................ 1-14

Figure 1-22 Advanced Parameter Manager.RNC Configuration SupplementInformation............................................................................................ 1-15

Figure 1-23 Advanced Parameter Manager.Service Basic ConfigurationInformation............................................................................................ 1-15

Figure 1-24 Advanced Parameter Manager.FACH Traffic ControlInformation............................................................................................ 1-16

Figure 1-25 Advanced Parameter Manager.UE Inter-frequency MeasurementConfiguration ........................................................................................ 1-16

Figure 1-26 Advanced Parameter Manager.UE Inter-Rat Measurement Relative toTraffic Category .................................................................................... 1-17

Figure 1-27 Advanced Parameter Manager.MBMS ConfigurationInformation............................................................................................ 1-17

Figure 1-28 Advanced Parameter Manager.Transport Format Set........................... 1-18

Figure 1-29 Advanced Parameter Manager.RNC Radio ResourceManagement......................................................................................... 1-18

Figure 1-30 Advanced Parameter Manager.Iu Interface and ConstantsInformation............................................................................................ 1-19

Figure 1-31 Advanced Parameter Manager.Service Physical Layer ConfigurationInformation............................................................................................ 1-19

Figure 1-32 Advanced Parameter Manager.CN System Information ....................... 1-20

Figure 1-33 Advanced Parameter Manager.HSPA Configuration Information ........... 1-20

Figure 1-34 Advanced Parameter Manager.UE Inter-frequency MeasurementRelative to Traffic Category................................................................... 1-21

Figure 1-35 Advanced Parameter Manager.Transport Format Combination Set ofPRACH................................................................................................. 1-21

Figure 1-36 Advanced Parameter Manager.Global Access Control ......................... 1-22

Figure 1-37 Advanced Parameter Manager.Traffic-Related Power Control.............. 1-22

Figure 1-38 Advanced Parameter Manager.UE Intra-frequency MeasurementRelative to Traffic Category Configuration Information........................... 1-23

Figure 1-39 Advanced Parameter Manager.E-DCH Reference ConfigurationInformation............................................................................................ 1-23

Figure 1-40 Advanced Parameter Manager.UE Traffic Volume MeasurementConfiguration ........................................................................................ 1-24

Figure 1-41 Advanced Parameter Manager.NodeB Common MeasurementConfiguration ........................................................................................ 1-24

II

Figures

Figure 1-42 MODIFYING ADVANCED PARAMETER 1........................................... 1-25



Figure 1-45 Deleting RNC Radio Resource Management ....................................... 1-28

Figure 1-46 Information Dialog Box for Deleting RNC Radio ResourceManagement......................................................................................... 1-28

Figure 1-47 Creating Node B Configuration Information .......................................... 1-29

Figure 1-48 Node B Configuration Information Dialog Box ...................................... 1-30

Figure 1-49 Modifying Advanced Parameter ........................................................... 1-31

Figure 1-50 Advanced Parameter Manager Dialog Box (Node B ConfigurationInformation) .......................................................................................... 1-31

Figure 1-51 Selecting Batch Modify......................................................................... 1-32

Figure 1-52 Select Batch Modify Objects Tab.......................................................... 1-33

Figure 1-53 Please Select Root Object Interface..................................................... 1-33

Figure 1-54 Add Filter Interface............................................................................... 1-34

Figure 1-55 Selecting Add....................................................................................... 1-34

Figure 1-56 Newly-added Information Column on Add Filter Interface..................... 1-35

Figure 1-57 Selecting Filtering Condition 1.............................................................. 1-35

Figure 1-58 Selecting Filtering Condition 2.............................................................. 1-36

Figure 1-59 Filling in Filtering Condition .................................................................. 1-36

Figure 1-60 Query Result........................................................................................ 1-37

Figure 1-61 NodeB Configuration Information Tab................................................... 1-37

Figure 1-62 Creating External UTRAN Cell ............................................................. 1-38

Figure 1-63 External UTRAN Cell Dialog Box (Global Information Tab)................... 1-39

Figure 1-64 External UTRAN Cell Dialog Box (Global Else Tab).............................. 1-39

Figure 1-65 External UTRAN Cell Dialog Box (LCS Tab)......................................... 1-40

Figure 1-66 External UTRAN Cell Dialog Box (Antenna Tab) .................................. 1-40


Figure 1-68 Advanced Parameter Manager Dialog Box (External UTRANCell) ...................................................................................................... 1-41

Figure 1-69 Creating External GSM Cell ................................................................. 1-43

Figure 1-70 External GSM Cell Dialog Box ............................................................. 1-43


Figure 1-72 Advanced Parameter Manager Dialog Box........................................... 1-44

Figure 1-73 Creating UTRAN Cell ........................................................................... 1-46

III


Figure 1-74 Business UTRAN Cell Dialog Box (UTRAN Cell Global InformationTab) ...................................................................................................... 1-46

Figure 1-75 Business UTRAN Cell Dialog Box (Cell Setup Parameters Tab) ........... 1-47

Figure 1-76 Business UTRAN Cell Dialog Box (LCS and Cell Antenna Tab) ........... 1-47

Figure 1-77 Business UTRAN Cell Dialog Box (Cell Ability and Cell ReselectionTab) ...................................................................................................... 1-48

Figure 1-78 Business UTRAN Cell Dialog Box (OCNS Parameter Tab)................... 1-48

Figure 1-79 Business UTRAN Cell Dialog Box (Status Info Tab) ............................. 1-49


Figure 1-81 Advanced Parameter Manager.MBMS Configuration Information in aCell ....................................................................................................... 1-50

Figure 1-82 Advanced Parameter Manager.Load Control Relationship ................... 1-50

Figure 1-83 Advanced Parameter Manager.SCPICH .............................................. 1-51

Figure 1-84 Advanced Parameter Manager.Balance Information............................. 1-51

Figure 1-85 Advanced Parameter Manager.PCPICH .............................................. 1-52

Figure 1-86 Advanced Parameter Manager.FACH .................................................. 1-52

Figure 1-87 Advanced Parameter Manager.UE Traffic Volume MeasurementConfiguration Information in a Cell ........................................................ 1-53

Figure 1-88 Advanced Parameter Manager.SCCPCH............................................. 1-53

Figure 1-89 Advanced Parameter Manager.MICH................................................... 1-54

Figure 1-90 Advanced Parameter Manager.NodeB Common MeasurementConfiguration Information in a Cell ........................................................ 1-54

Figure 1-91 Advanced Parameter Manager.PRACH ............................................... 1-55

Figure 1-92 Advanced Parameter Manager.PCH .................................................... 1-55

Figure 1-93 Advanced Parameter Manager.UE Measurement Configuration inSystem Information Block ..................................................................... 1-56

Figure 1-94 Advanced Parameter Manager.UTRAN Cell......................................... 1-56

Figure 1-95 Advanced Parameter Manager.UE Internal MeasurementConfiguration Information in a Cell ........................................................ 1-57

Figure 1-96 Advanced Parameter Manager.PSCH.................................................. 1-57

Figure 1-97 Advanced Parameter Manager.PICH ................................................... 1-58

Figure 1-98 Advanced Parameter Manager.RACH.................................................. 1-58

Figure 1-99 Advanced Parameter Manager.AICH ................................................... 1-59

Figure 1-100 Advanced Parameter Manager.HSPA Configuration Information in aCell ....................................................................................................... 1-59

Figure 1-101 Advanced Parameter Manager.Cell-Related Access Control .............. 1-60

Figure 1-102 Advanced Parameter Manager.SSCH................................................ 1-60

IV

Figures

Figure 1-103 Advanced Parameter Manager.Cell Enhanced FACH......................... 1-61

Figure 1-104 Advanced Parameter Manager.PCCPCH........................................... 1-61

Figure 1-105 Advanced Parameter Manager.BCH .................................................. 1-62

Figure 1-106 Advanced Parameter Manager.HS-PDSCH Measurement PowerOffset.................................................................................................... 1-62

Figure 1-107 Advanced Parameter Manager.Power Control not Related toService ................................................................................................. 1-63

Figure 1-108 Creating GSM Neighbouring Cell ....................................................... 1-65

Figure 1-109 GSM Neighbouring Cell Dialog Box.................................................... 1-65

Figure 1-110 Modifying Advanced Parameter.......................................................... 1-66

Figure 1-111 Advanced Parameter Manager Dialog Box ......................................... 1-67

Figure 1-112 Creating Neighbouring Cell ................................................................ 1-69

Figure 1-113 Neighbouring Cell Dialog Box............................................................. 1-69


Figure 1-115 Advanced Parameter Manager Dialog Box......................................... 1-70

Figure 1-116 Creating Cell Selection and Cell Reselection...................................... 1-72

Figure 1-117 Cell Selection and Cell Reselection Dialog Box .................................. 1-72



Figure 1-120 Creating UTRAN Cell Information in MBMS Service Area .................. 1-75

Figure 1-121 UTRAN Cell Information in MBMS Service Area Dialog Box............... 1-75

Figure 1-122 Modifying Advanced Parameter ......................................................... 1-76


Figure 1-124 Creating User Authorized PLMN+SNAC Information .......................... 1-78

Figure 1-125 User Authorized PLMN+SNAC Information Dialog Box ...................... 1-78

Figure 1-126 Creating LAC and SNAC Information ................................................. 1-80

Figure 1-127 LAC and SNAC Information Dialog Box ............................................. 1-80

Figure 2-1 Starting Template Manager ...................................................................... 2-2

Figure 2-2 Input Dialog Box ...................................................................................... 2-2

Figure 2-3 Parameter Template Manager.................................................................. 2-3


Figure 2-5 Creating a New Template......................................................................... 2-4



Figure 2-8 Successfully Creating a New Template .................................................... 2-5

Figure 2-9 Selecting a Template................................................................................ 2-6

V


Figure 2-10 Template Information ............................................................................. 2-6

Figure 2-11 Modifying Template Information.............................................................. 2-7

Figure 2-12 Input Dialog Box .................................................................................... 2-8

Figure 2-13 Save Dialog Box .................................................................................... 2-8

Figure 2-14 Info Dialog Box ...................................................................................... 2-9

Figure 2-15 Importing Parameter Template ............................................................... 2-9

Figure 2-16 Open Dialog Box.................................................................................. 2-10

Figure 2-17 Info Dialog Box .................................................................................... 2-10

Figure 2-18 Deleting Template ................................................................................ 2-11

Figure 2-19 Confirm Dialog Box .............................................................................. 2-11

Figure 2-20 Template Comparison Dialog Box 1 ..................................................... 2-12

Figure 2-21 Template Comparison Dialog Box 2 ..................................................... 2-13

Figure 2-22 Template Application Dialog Box 1 ....................................................... 2-14

Figure 2-23 Template Application Dialog Box 2 ....................................................... 2-14

Figure 2-24 Info Dialog Box (Select Subnet ID)....................................................... 2-15

Figure 2-25 Info Dialog Box (Select Configuration Set ID)....................................... 2-15

Figure 2-26 Success Dialog Box ............................................................................. 2-15

VI

TablesTable 1-1 Operations about ZXWR RNC Radio Resource Configurations ................. 1-2

Table 1-2 SHORTCUT MENU ON RNC RADIO RESOURCE MANAGEMENTTAB........................................................................................................ 1-27

Table 1-3 Shortcut Menu on Node B Configuration Information Tab ........................ 1-31

Table 1-4 Shortcut Menu on External UTRAN Cell Tab............................................ 1-41

Table 1-5 Shortcut Menu on External GSM Cell Interface........................................ 1-45

Table 1-6 SHORTCUT MENU ON UTRAN CELL TAB ............................................ 1-63

Table 1-7 SHORTCUT MENU ON GSM NEIGHBOURING CELLINTERFACE........................................................................................... 1-67

Table 1-8 Shortcut Menu on Neighbouring Cell Interface......................................... 1-71

Table 1-9 Shortcut Menu on Cell Selection and Reselection Interface ..................... 1-74

Table 1-10 Shortcut Menu on UTRAN Cell Information in MBMS Service AreaInterface................................................................................................. 1-77

Table 1-11 Shortcut Menu on User Authorized PLMN+SNAC InformationTab......................................................................................................... 1-79

Table 1-12 Shortcut Menu on LAC and SNAC Information Interface........................ 1-81

Table 2-1 Toolbar of Template Manager .................................................................... 2-1

VII

Tables

This page intentionally left blank.

GlossaryNMS- Network Management System

IX

Documents

ZXWR RNC (V3.09.30) Radio Network Controller Radio Configuration Operation Guide