Your supplier of choice for peripheral HVAC control ...TCI-C13 Universal controller cabinet mounted 2 universal inputs ... function based on enthalpy or temperature Set point limitations

Product Guide 2014

© Vector Controls GmbH, Switzerland Page 1

Your supplier of choice

for peripheral HVAC control products since 2001

Carefully selected, installed and adjusted control products

save energy, reduce system lifecycle cost and increase tenant

satisfaction.

Vector Controls is a global company specializing in sensors

and controls.

Our mission is to design, build, distribute and support

feature-rich, easy-to-use products that help you optimize the

indoor environment.

▲ Temperature and humidity controls easily configured by

straightforward on-board parameter setting.

▲ Universal controllers with freely assigned inputs and outputs

for flexibility in a wide range of applications.

▲ Temperature, humidity and CO2 transmitters and sensors for

room, duct, and outdoor applications.

▲ Wide range of temperature sensor types and selectable

accuracy levels.

Index

Fan coil and binary controls 2

Single loop temperature & humidity controls 4

Universal controls 5

Temperature sensors 7

Temperature and humidity transmitters 8

Differential pressure and PT1000 transmitters 9

Accessories 10

Standard terms of warranty and sales 11

Product Guide 2014


TLC3

OPR-1

TLC3 Series Fan Coil and Binary Controller

Compact wall mounted controller for line voltage for flush mounting. The controller is available in two different

housing to fit different connection boxes.

Large LCD display

Programmable user and expert parameters

Low power consumption of 1W

Flush mounting

AC 230VAC or 24V AC or DC

Deluxe version with backlight, clock and infrared remote control possibilities

Relay switching for binary outputs

Energy saving with comfort and economy modes and automatics fan speeds switching for FCR models

Set point limitations

IP 30

Special functions including frost protection, comfort/ economy mode change based on temperature input, and more

Model Functions & Variations Features

TLC3-BCR

Thermostat

2 pipe control for three-state valve

2 binary outputs (relays) for valve

1 internal temperature sensor

TLC3-FCR

Fan coil controller

2 pipe fan coil control

3 binary outputs (relays) for fan

1 binary output (relays) for valve


TLC3-FCR-T

Fan coil controller

2-pipe fan coil control with external

input




1 external sensor input

TLC-FCR-2

Fan coil controller

4-pipe fan coil control


2 binary outputs (TRIAC for -230, relays for -24) for valve


TLC3-FCR-M2

Fan coil controller

2-pipe PI Fan Coil Controller

1 TI internal, 2 external input

3 DO (relays) Fan control

1 AO (0-10VDC) PID valve control

TLC3-FCR-M4

Fan coil controller

4-pipe PI Fan Coil Controller

1 TI internal, 1 external input

3 DO (relays) Fan control

2 AO (0-10VDC) PID valve control

TLC3 Variations:

-D = deluxe version

-24 = 24VADC

-230 = 230VAC

-W01 = Cooling only

With backlight, real time clock and time schedules

Power supply 24VAC or 24VDC

Power supply 230VAC

Fixed to cooling only mode

OPR-1 Infrared remote controller Infrared remote controller for deluxe versions

Product Guide 2014


TLR

OPA-D

OPR-1

TLR Series Fan Coil and Package Unit Controller

Fan Coil unit controller consisting of a cabinet mounted base unit and a surface mounted operation

terminal/temperature sensor.

Large LCD display on operation terminal


Base cabinet mounted, terminal wall flush mounted

AC 230V or AC 24V 50/60 Hz


High switching power for each outputs up to 10 (6) A 250 VAC

Energy saving with comfort and economy modes and automatics fan speeds switching for fan coil models

Base unit IP20, Operation terminal IP30

Master/slave options. 1 operation terminal may drive up to 8 base units.


OPA-Dx*

Operation terminal for TLR

Different operation terminals for different

base units

Dx* = D5, D5F, D41, D5P

-D = deluxe version


-D: With backlight, real time clock and time schedules

TLR-D5-24

TLR-D5-230

Fan coil controller, base unit

Base unit for OPA-D5 or OPU-D5

4 pipe fan coil control

3 relays outputs for fan

2 relays output for valve


TLR-D5F-24

TLR-D5F-230

Fan coil controller for floating valve,

base unit

Base unit for OPA-D5F or OPU-D5F

2 pipe PI fan coil control

3 relays outputs for fan

2 TRIAC output for floating actuator


TLR-D41-24

TLR-D41-230

Fan coil controller for modulating

valve, base unit

Base unit for OPA-D41 or OPU-D41

2 pipe PI control, fan coil control



1 0-10V output for modulating actuator


TLR-D5P-24

TLR-D5P-230

Package unit controller, base unit

Base unit for OPA-D5P or OPU-D5P

4 pipe package unit control


4 binary outputs (relays) for heating / cooling stages or

reversing valves


TLR Variations:

-24 = 24VADC

-230 = 230VAC

Power supply 24VAC or VDC

Power supply 230VAC

OPR-1 Infrared remote controller Infrared remote controller for Deluxe types

Product Guide 2014


TCY

TDC

TEM-TEF

Single loop Temperature and Humidity Controls

TCY types are compact binary or PID humidity or temperature controllers for flush mounting. TDC-BH is a duct

mounted humidistat. TCY-MZ is a compact positioner for comfort ventilation. TEF and TEM are surface mounted PI

temperature controllers.

Large LCD display on operation for TCY, TDC


Low power consumption of 1 W

AC 24V 50/60 Hz


Energy saving with comfort and economy modes and automatics fan speeds switching for fan coil models


IP30

Special functions including frost protection, comfort/economy mode change based on temperature input and more.


TCY-BH

Humidistat wall mounted

Binary humidifying or dehumidifying

with optional fan support

2 binary outputs (relays)

1 internal humidity sensor, accuracy 5%

1 external temperature sensor input

TDC-BH

Humidistat duct mounted

Binary humidifying or dehumidifying

with optional fan support


1 internal humidity sensor, accuracy 5%

1 external temperature sensor input

TCY-MT2

PI temperature controller

2-pipe PI temperature control for modulating

actuators

1 AO 0-10VDC

1 internal temperature sensor, 2 external passive inputs

TCY-MT4


4-pipe PI temperature control for modulating

actuators

2 AO 0-10VDC


TCY-FT2


2-pipe PI temperature control for floating

actuators

2 TRIAC outputs for 1 3-state valve


TCY-FT4


4-pipe PI temperature control for floating

actuators

4 TRIAC outputs for 2 3-state valves


TCY-MZ2

NEW!

Positioner for comfort ventilation

Positioning for ventilation systems

-D: with time schedule and backlight

2 analog outputs,

1 external passive input

TEM

2-pipe PI universal controller

Universal surface mounting

PI universal control

1 AO 0-10VDC/ 1 AI 0-10VDC

1 internal temperature sensor, 1 external passive input

TEF

2-pipe PI controller for floating output

or 4-pipe binary control

Universal surface mounting


1 internal temperature sensor, 1 external passive input

Product Guide 2014


TCI-W

TCI-C

TCI Series Universal Controls

TCI series controllers are compact universal single and dual loop PI controllers for flush wall or cabinet mounting

Universal controllers with up to 2 control loops


Low power consumption of 1 W

AC/DC 24V 50/60 Hz

-C2x or –W2x version with backlight, clock and times schedules

Free assignable inputs and outputs

Energy saving with comfort and economy modes


IP30

Advanced control functions including alarms with configurable action at alarm state, cascading control loops, manual override of analog outputs and more

Special functions for remote enable/disable, remote heating/cooling change and more

Model Variations Features

TCI-W11

TCI-W11-H

Universal controller wall mounted

Single loop controller with PI and binary sequences

-H = int humidity sensor with accuracy 3% NEW!

1 universal input (NTC, VDC, mA)

2 binary outputs (relays), 1 analog output (VCD, mA)

TCI-W13

TCI-W13-H

Universal controller wall mounted


-H = int humidity sensor with accuracy 3% NEW!

1 universal input (NTC, VDC, mA)

1 binary output (relays), 2 analog outputs (VCD, mA)

TCI-W22

TCI-W22-H

Dual loop universal controller wall mounted

Dual loop controller with PI and binary sequences

-H = int humidity sensor with accuracy 3%

2 universal inputs (NTC, VDC, mA)


TCI-W23

TCI-W23-H

Dual loop universal controller wall mounted


-H = int humidity sensor with accuracy 3%

1 universal input (NTC, VDC, mA), 1 passive input (NTC)

1 binary output (relays), 2 analog outputs (VCD, mA)

TCI-C11 Universal controller cabinet mounted







2 TRIAC outputs, 1 analog output (VCD, mA)



2 universal inputs (PT1000/NI1000, VDC, mA)





2 binary outputs (TRIAC), 1 analog output (VCD, mA)

TCI-C22 Dual loop universal controller cabinet mounted



2 binary outputs (relays), 2 analog outputs (VCD, mA)




2 binary outputs (relays), 2 analog outputs (VCD, mA)




2 binary outputs (TRIAC), 2 analog outputs (VCD, mA)

AMM-2 Mounting kit for front panel mounting

Product Guide 2014


OPA2

TCX2-OP

TCX2 Series Universal Controls

TCX2 series controllers are communicating universal multiple loop PI controllers for cabinet mounting.

OPA2 is the remote operation terminal for the TCX2 type of products.

Universal controller with up to 4 control loops


Communicating with BACnet MS/TP and MODBUS

RS485 communication

Copy parameter sets with the AEC-PM1 memory plug-in

Free heating or cooling with economizer function based on enthalpy or temperature


Time schedule, clock with backup for 40863 type

Optional integrated operation terminal for -40863 type

Advanced control functions including alarms with configurable action at alarm state, cascading control loops, manual override analog outputs and more

Special functions for remote enable/disable, remote heating/cooling change and more


TCX2-40863(-OP)

TCX2-40863(-OP)-BAC

TCX2-40863(-OP)-MOD!

Universal controller cabinet mounted

4 control loops with PI and binary sequences

-OP: integrated operation terminal

-BAC: Communication for BACnet® MS/TP

-MOD: Communication for Modbus

8 universal inputs (NTC, VCD, mA)

6 binary outputs (relays),

3 analog outputs (VCD, mA)

TCX2-13343-MOD

TCX2-13343-BAC

Single loop controller cabinet mounted

1 control loop with PI and binary sequences



Ideal for VAV zone control

3 analog inputs (VCD), 3 passive inputs (NTC)

4 Binary outputs (relays), 3 analog outputs (VCD)

TCX2-14050-MOD

TCX2-14050-BAC





Ideal for fan coil applications

4 passive inputs (NTC)


TCX2-14273-24

TCX2-14273-24-MOD

TCX2-14273-24-BAC

TCX2-14273-230

TCX2-14273-230-MOD

TCX2-14273-230-BAC





-24: 24V AC power supply

-230: 230VAC power supply

Ideal for zoning and general applications

4 passive inputs (NTC)

2 analog inputs (VCD)

4 binary outputs (relays 2A)

1 binary output (relays 10A)

2 TRIAC outputs (24VAC switching to GND)

230VAC types with 5VA 24VAC output

OPA2-VC Operation terminal for TCX2

RS-485 Communication with TCX2


OPA2-2T-VC

OPA2-2HT-VC

Operation terminal for TCX2

With RH sensor 3% accuracy

1 internal temperature and RH sensor

2 passive inputs (NTC or open contact)

AEX-MOD Modbus Plug-in for TCX2 For Modbus slave communication

AEX-BAC BACnet Plug-in for TCX2 For BACnet® MS/TP communication

AEC-PM1 Parameter memory backup for TCX2

Plug-in device to copy configuration of TCX2

Holds 4 parameter sets of TCX2

AEC-USB-01 RS485 to USB converter Parameter exchange with EasySet download SW

Product Guide 2014


S-T

SD-T

SDB-T

SOD-T

SRA-T

S-T, SD-T, SDB-T, SOD-T, SRA-T Temperature Sensors

Passive temperature sensors for a large variety of installation options and applications

NTC, PT1000 and NI 1000 elements

Rigid housing

IP65 for SOD-T, SDB-T, S-T and IP30 for SRA-T

AMI immersion well for pipe applications (duct sensors)

Large selection of sensing element types and curves

Cable gland or conduit connectors for SDB and SOD

Special elements or probe design available upon request


S-Txx*-2 Flying lead temperature sensor

-2 = 2m cable

-Txx* = see probe selection

Passive temperature sensor

SC-Txx*-2

SC-Tpx* NEW!

Flying lead contact sensor

-2 = 2m cable


Passive temperature sensor for contact mounting

on pipes

SD-Txx*-12-2

SD-Txx*-20-2

Flying lead duct temperature sensor

Probe length = 12cm

Probe length = 20cm

-2 = 2m cable


Passive temperature sensor for duct mounting

SDB-Txx*-12

SDB-Txx*-20

Duct temperature sensor

Probe length = 12cm

Probe length = 20cm


Passive temperature sensor for duct mounting

with conduit connector

SOD-Txx* Outdoor temperature sensor


Passive temperature sensor for outdoor mounting

with conduit connector

SRA-Txx* Indoor temperature sensor


Passive temperature sensor for indoor mounting

*Probe selection (-Txx)

-Txx Sensing element Features

-Tn3

-Tn10

-Tn11

-Tn20

-Tn100

NTC 3kΩ at 25°C

NTC 10kΩ at 25°C

NTC 10kΩ at 25°C

NTC 20kΩ at 25°C

NTC 100kΩ at 25°C

B35/50: 3935

B35/50: 3935

B35/50: 3630

B35/50: 4200

B35/50: 4200

-Tp1

-Tp2

-Tk5

PT100

PT1000

NI1000

EN60751

EN60751

5000 ppm/K

Product Guide 2014


SRC

SDC

SOC

AES

OPA-S

OPC-S

SRC, SDC, SOC Temperature and Humidity Transmitters

Active temperature & humidity transmitter for a large variety of installation options and applications

3-wire transmitters with selectable 0/2-10V or 0/4-20mA outputs ranges

Rigid housing

Duct (SDC) and outdoor (SOC) transmitters have IP54 housings- IP63 with AMS-1 weather shield. Room transmitter (SRC) is IP30.

5%, 3% or 2% humidity accuracy


Programmable output signal and temperature sensing ranges, plus min. and max value memory, with OPA-S remote or OPC-S integrated display/programming terminal.

AMI immersion well for pipe applications (for duct temperature transmitters)


SRC-T1

SRC-H1

SRC-H1T

SRC-H1T1

SRC-C1

Transmitter for indoor mounting

Temperature transmitter

Humidity transmitter

Humidity transmitter with probe

Temperature and humidity transmitter

Indoor CO2 transmitter: 0-2000 ppm

Programmable transmitter 3-wire connection

Output signal selectable with jumper

(VCD, mA). Options:

- Accuracy RH sensor (2,3,5%, default 3%)

- OPA-S remote display

SDC-T1-x

SDC-H1-x

SDC-H1T-x

SDC-H1T1-x

SDC-C1

Transmitter for duct mounting





Duct CO2 transmitter: 0-2000ppm

-x = probe length:

-8 = 8cm

-16 = 16 cm

-24 = 24 cm (only for SDC-T1)



(VCD, mA)

Options:


- Conduit connector or cable gland

- OPC-S display option

SOC-T1

SOC-H1

SOC-H1T

SOC-H1T1

Transmitter for outdoor mounting







(VCD, mA). Options:


- Conduit connector or cable gland,

- OPC-S display option

- AMS-1 weather shield

AES-HT: Sensing element selection

Element Sensing element Features

AES-HT-A5

AES-HT-A3

AES-HT-A2

Humidity sensing element:

Needed for –H1, -H1T1

5% accuracy

3% accuracy

2% accuracy

AES-HTn3-A3

AES-HTn10-A3

AES-HTn11-A3

AES-HTn20-A3

AES-HTn100-A3

Humidity sensing element for –H1T transmitters

NTC 3kΩ at 25°C

NTC 10kΩ at 25°C

NTC 10kΩ at 25°C

NTC 20kΩ at 25°C

NTC 100kΩ at 25°C

3% accuracy

B35/50: 3935

B35/50: 3935

B35/50: 3630

B35/50: 4200

B35/50: 4200

Product Guide 2014


SDA-P

SCC-T1-Tp2

OPA-S

OPC-S

Differential Pressure & PT1000 Transmitter

The SDA-P is a differential pressure transmitter with programmable output range and min max memory.

The SCC-T1-Tp2 is a programmable accurate signal converter for PT1000 sensing elements

3-wire transmitters with voltage and current outputs

Rigid housing

Remote display

Cable gland or conduit connectors for SCC

Programmable with OPC-S and OPA-S min. max memory

Integrated display for SCC with OPC-S


SDA-P1

SDA-P2

SDA-P3

SDA-P4

SDA-P5

Differential pressure transmitter

Pressure range: 0...300Pa

0...500Pa

0...1kPa

0...3kPa

0...5kPa


Output signal selectable with jumper (VCD, mA)

Options:

- OPA-S remote display

SCC-T1-Tp2

PT1000 signal converter

Conversion range -40…400°C

Signal converter for a PT1000 input signal. Conversion

to voltage or current signal, selectable with jumper

Options:

- AMC-1 cable gland

- AMC-2 conduit connector

- OPC-S integrated display

OPC-S

Integrated display and programming unit

Used for SCC, SDC, SOC transmitters

Plug-in to transmitter to display min – max values,

current values and to program input and output

ranges

OPA-S

Remote display and programming unit

Used for SDA, SDC, SOC, SRC transmitters

Plug-in to transmitter to display min – max values,

current values and to program input and output

ranges

OPA2-MOD

Universal operation terminal for Modbus

The OPA2-MOD is a universal operation

terminal for RS-485 Modbus communication

- 2 passive inputs - 1 internal temperature

- 1 optional internal humidity sensor

Product Guide 2014


AMC-1

AMC-2

AMI

AMS-1

AES

OPR-1

AEC-PM1

Accessories

AMI immersion well for pipe applications (duct sensors and temperature transmitters)


Flush mounting box for TCY, TLC-FCR series

Flush mounting box for TCI-W, TCY, TLC-FCR series

Infrared remote controller OPR-1

Humidity & temperature sensing elements

Plug-in modules


AMI-S5-1

AMI-S7-1

AMI-S10-1

AMI-S15-1

Stainless Steel pocket

Length 5cm

Length 7cm

Length 10cm

Length 15cm

Stainless steel pocket with fixing screw

For immersion mounting of SD-T or SDB-T

AMC-1

AMC-2

Cable gland

Conduit connector

Cable gland and conduit connector needed for SDC and

SOC, SCC

AMS-1 Weather shield for SOC, SDC Option for SOC-H1, H1T, H1T1, T1

AMB-001

AMB-005

Flush mounting box

Flush mounting box

OPR-1 Infrared remote controller Infrared remote controller for Deluxe types fan coil

controller

AER-C13 Converter AO-DO AO-DO converter 1AO to 3 DO adjustable switching

point

AET-230-10

AET-230-30

AET-230-50

Transformer 230V to 24VAC 10 = 10 VA

30 = 30 VA

50 = 50 VA

AES-HT-A5

AES-HT-A3

AES-HT-A2

Humidity sensing element: Needed for

–H1, -H1T1

5% accuracy

3% accuracy

2% accuracy

AES-HTn3-A3

AES-HTn10-A3

AES-HTn11-A3

AES-HTn20-A3

AES-HTn100-A3

Humidity sensing element for –H1T

transmitters

NTC 3kΩ at 25°C

NTC 10kΩ at 25°C

NTC 10kΩ at 25°C

NTC 20kΩ at 25°C

NTC 100kΩ at 25°C

3% accuracy

B35/50: 3935

B35/50: 3935

B35/50: 3630

B35/50: 4200

B35/50: 4200

AES-HTp1-A3

AES-HTp2-A3

AES-HTk5-A3

PT100

PT1000

NI1000

EN60751

EN60751

5000 ppm/K

Product Guide 2014


Standard terms and conditions of international warranty and sales

General

Until otherwise arranged, in writing, the following conditions are valid. The terms stated in this Agreement take precedence over any conditions, which may appear on a standard order form of Buyer, and no such contradictory provisions or conditions, if any, of such form, except as expressly stated herein, shall be binding. Notice of objection to any additional or different terms or conditions is hereby given.

Price

Our prices are net, ex works factory Beijing, China (EXW = Ex works Incoterms 2000) in USD unless specified otherwise. Delivery costs will be charged at cost. We are entitled to make partial deliveries, when necessary, which can be invoiced separately. Packing for normal consignments is included in the price. Wooden crates, pallets, etc. will be charged separately. Wiring diagrams, installation and commissioning are not included in our prices. The prices do not include tax of any type or custom duties and similar tariffs and fees, which may now or hereafter be applicable to, measured by, or imposed upon or with respect to the transactions described herein, the Products, the sale of the Products, their value, or their use, or any services performed in connection therewith. Buyer agrees to pay or, at Vector Controls option, reimburse Vector Controls for any such taxes and charges which Vector Controls or its subcontractors, suppliers or affiliates are required to pay. Vector Controls is entitled to change its prices without notice. Quotations remain valid for 3 month from date of quotation unless specified otherwise.

Payment

Invoices are payable in USD according to agreed terms without any deductions. Payment is not affected by the date of receipt. If, in the judgment of Vector Controls, the financial condition of Buyer, at any time during the manufacturing period or at any time before the applicable Products are shipped to Buyer, does not justify the terms of payment specified, Vector Controls may require full payment in advance. An interest charge of 2% per month will be included on all overdue payments. Shipments for new orders and warranty replacements will not be made if payment is overdue.

Delivery

We undertake to make every endeavor to adhere to our delivery promise(s), but do not accept cancellation of contract or liability for any direct or indirect losses which may arise, for any reason whatsoever, due to our failure to adhere to such promise(s). If Vector Controls is late in delivery it is assumed that the Buyer still insists on delivery. The day of delivery is the day the goods are collected from the factory. In case the goods are not collected on the agreed date, Vector Controls is entitled to invoice the goods and store them on cost and risk of the Buyer. Vector Controls reserves the right not to supply the products ordered in case they are not available anymore. In such a case Vector

Controls will immediately inform the Buyer and refund an already made down payment.

Title and Risk

The products shall remain the personal property of Vector Controls until full settlement of all claims existing against the Buyer. The Buyer agrees to perform all acts which may be necessary or appropriate to perfect and assure the retention of title in Vector Controls of all of the Products until such point in time; Title and risk pass to Buyer according the agreed terms of delivery (Incoterms 2000).

Return of Goods

Standard goods received by the Buyer can be returned if agreed upon with Vector Controls and if goods are still part of the standard sales program, less than 6 month old, unused, in original packaging and in good condition. There is no obligation for Vector Controls to accept returned goods. A return for custom made products is not possible. An overhead charge of 10% of the invoice value will be deducted. Products are to be returned to a previously assigned Vector Controls Factory on the cost of the Buyer.

Specifications

The data which were published in Vector Control catalogs, brochures, websites, install sheets or other publications describe the nature and application of the products of Vector Controls, and are not a quality or durability guarantee. The make of the delivered products may differ in material, color or shape from pictures or exhibits. Vector Controls assumes no responsibility regarding the suitability or fitness of products for a particular purpose. Specifications communicated by Vector Controls are to be regarded as orientation guidelines. Vector Controls reserves the right to change product specifications without notice.

Warranty

Vector Controls guarantees that the Delivered products fulfill the specifications outlined in the associated datasheets. Other warranty aspects are excluded to extent permitted by law. We undertake to replace or repair free of charge, any part or parts of equipment, which may develop defects, caused through faulty material or workmanship within 18 months from the date of invoice. The consequences of ordinary wear and tear, damage due to negligence or improper use, or other causes beyond our control are excluded from this guarantee. This guarantee shall be null and void should the Buyer or any other persons:

Use the products in applications or environments which are not specified in datasheets, especially in areas where failure could lead to loss of life or property;

Does not follow local rules and regulations or disregards technical specifications and mounting instructions;

Use the products under special conditions, especially in an environment of aggressive gases or liquids or outside the permissible environmental parameters;

modify or repair any part of our equipment;

Store the products not appropriately.

Disclaimer

In the event of a breach of this warranty, Vector Controls sole responsibility shall be to furnish a replacement part EXW factory or, at the option of Vector Controls, to repair the defective part. Vector Controls hereby excludes all implied warranties of merchantability and fitness and all other express or implied warranties whatsoever with respect to the products. In no event shall Vector Controls be liable for loss of profit, loss of production, loss of business or goodwill, liability of Buyer or ultimate user to others, increased or uncovered operating or fixed costs, inefficiency, theft or any other consequential or indirect or remote damages in any manner directly, or indirectly, related to design, manufacturing, supply or use of the Products or any other act or failure to act by Vector Controls or its agents or contractors. All products are designed for use ONLY as operating controls. Where an existing control failure would result in personal injury and/or loss of property including property damage, it is the responsibility of the Buyer to add any devices (safety, limit controls) or systems (alarm, supervisory) that protect against, or warn of, control failure.

Indemnification

The buyer will fully indemnify Vector Controls on first demand against all third party claims, which they are facing. This also applies to claims under product liability.

Damage or Loss in Transit

Vector Controls shall not be liable for failure to perform or for delay in performance due to fire, flood or other natural cause, strike or other labor difficulty, act of any governmental authority or of Dealer or its agents or customers, riot, embargo, car shortage, wrecks or transportation delays or failure, inability to obtain necessary labor, materials, or manufacturing facilities from usual sources or due to any other unforeseen circumstance or cause beyond its reasonable control. In the event of delay in performance due to any such cause, the date of delivery or time for completion shall be postponed by such length of time as may be reasonably necessary to compensate for the delay.

Alterations of standard terms

Vector Controls reserves the right to change its terms and conditions of sales at any time without notification.

Efficacy in invalid clause

Should one or more provisions of these terms become invalid, the other terms and conditions herein are not affected and continue to be effective.

Proper Law and Jurisdiction

This contract is and shall be deemed to have been made in Switzerland, and shall in all respects, be governed by Swiss laws. For any dispute resulting from the implementation and application of this contract, the place of jurisdiction are the courts based in Zürich, Switzerland.

Product Guide 2014


Reliable, Flexible, Affordable

Worldwide!

Quality - Innovation - Partnership

Vector Controls GmbH

Poststrasse 20

CH-8620 Wetzikon

Switzerland

Tel: +41 41 740 60 50 Fax: +41 41 740 60 51

[email protected]

www.vectorcontrols.com

Documents

Your supplier of choice for peripheral HVAC control ...TCI-C13 Universal controller cabinet mounted 2 universal inputs ... function based on enthalpy or temperature Set point limitations