Xerox-WC-5016-5020-Service manua.pdf

701P48365June 2008

Work Center 5016, 5020Service Documentation

CAUTIONCertain components in the Work Center 5016/ 5020 are susceptible to damage from electrostatic dis-charge. Observe all ESD procedures to avoid com-ponent damage.

AcknowledgementsPrepared by Global Knowledge & Llanguage Services - North America800 Phillips Road - Building 0218-01AWebster, New York 14580-9791ISO9001 AND ISO27001 Certified Copyright 2007-2008 by Xerox Corporation. All rights reserved.Xerox and all product names and number names are trademarks of Xerox Corporation.Printed in the USA

While Xerox has tried to make this documentation accurate, Xerox will haveno liability arising out of any inaccuracies or ommissions. Changes are peri-odically made to this document. Changes, technical inaccuracies, and typo-graphical errors will be corrected in subsequent editions.

All service documentation is supplied to Xerox external customers for infor-mational purposes only. Xerox service documentation is intended for use by certified product trained service personal only. Xerox does not warrant or represent that such documentation is complete, nor does Xerox represent or warrant that it will notify or provide to such customer any future changes to this documentation. Customer performed service of equipment, or mod-ules, components or parts of such equipment may affect the warranty offered by Xerox with respect to such equipment. You should consult the applicable warranty for its terms regarding customer or third party provided service. If the customer services such equipment, modules, components or parts thereof, the customer releases Xerox from any and all liability for the customer actions, and the customer agrees to indemnify, defend and hold Xerox harmless from any third party claims which arise directly or indirectly from such service.

WorkCentre 5016, 5020Reissue

mentioned in this publication are trademarks of rademarks are also acknowledged.

tone, Inc.

ument. Changes, technical inaccuracies, and typo-nt editions.

AUTIONradiate radio frequency energy, and if not installed ns documentation, may cause interference to radio und to comply with the limits for a Class A comput- of FCC rules, which are designed to provide rea-ce when operated in a commercial environment. l area is likely to cause interference in which case d to correct the interference.June, 2008i

Front Matter

WorkCentre 5016, 5020

Service Documentation

WorkCentre 5016, 5020 Service Documentation

701P48365

Reissue

June, 2008

***Xerox Private Data***

All service documentation is supplied to Xerox external customers for informational purposes only. Xerox service documentation is intended for use by certified, product-trained service per-sonnel only. Xerox does not warrant or represent that it will notify or provide to such customer any future change to this documentation. Customer performed service of equipment, or mod-ules, components, or parts of such equipment may affect whether Xerox is responsible to fix machine defects under the warranty offered by Xerox with respect to such equipment. You should consult the applicable warranty for its terms regarding customer or third-party provided service.

If the customer services such equipment, modules, components or parts thereof, the customer releases Xerox from any and all liability for the customer actions, and the customer agrees to indemnify, defend and hold xerox harmless from any third party claims which arise directly or indirectly for such service.

While Xerox has tried to make the documentation accurate, Xerox will have no liability arising out of any inaccuracies or omissions. Changes are periodically made to this document. Changes, technical inaccuracies, and typographical errors will be corrected in subsequent edi-tions.

Prepared by:

Xerox Corporation

Global Knowledge and Language Services

800 Phillips Road, Bldg. 0218-01A

Webster, New York 14580-9791

USA

2007 - 2008 by Xerox Corporation. All rights reserved.

Copyright protection claimed includes all forms and matters of copyrightable material and infor-mation now allowed by statutory judicial law or hereinafter granted, including without limitation, material generated from the software programs which are displayed on the screen such as icons, screen displays, looks, etc.

Printed in the United States of America.

XEROX and all Xerox product names XEROX CORPORATION. Other company t

PANTONE is a registered trademark of Pan

Changes are periodically made to this docgraphic errors will be corrected in subseque

CThis equipment generates, uses and can and used in accordance with the instructiocommunications. It has been tested and foing device pursuant to subpart B of part 15sonable protection against such interferenOperation of this equipment in a residentiathe user, at his own expense, will be require

WorkCentre 5016, 5020Reissue June, 2008

iiFront Matter

Introduction

IntroductionJune, 2008iWorkCentre 5016, 5020

Reissue

How To Use This Manual................................................................................................ iii

WorkCentre 5016, 5020ReissueJune, 2008

iiIntroduction

Introduction

tion

Symbolsout this service manual are described as follows:

ARNINGrating or maintenance procedure, practice, or ould result in personal injury or loss of life.AUTION

g or maintenance procedure, practice, or condition damage to, or destruction of, equipment.

ating or maintenance procedure, practice, or condi-efficiently.

nt and troubleshooting.

re for reference.

rence.

ic-sensitive IC chips, which could be damaged if not arding Safety Critical Components set by XEROX June, 2008iiiWorkCentre 5016, 5020

Reissue

How To Use This Manual

This manual is used as the standard service manual for the WorkCentre 5016, 5020.

Enter any comments and/or corrections regarding the WorkCentre 5016, 5020 Service Docu-mentationl on the Publication Comment Sheet, and send it to the Technical Support Center SDEG.

This manual describes the standard procedures for servicing the WorkCentre 5016, 5020. Refer to Section 1 Service Call Procedure for efficient and effective servicing during mainte-nance calls.

Contents of ManualThis manual is divided into nine sections as described below.

Section 1 Service Call Procedures

This section describes the structured process for determining the type and sequence of actions that are performed during a service call.

Section 2 Status Indicator RAPs

This section contains the Repair Analysis Procedures (RAPs) necessary to repair all faults other than image quality faults.

Section 3 Image Quality RAPs

This section contains the Repair Analysis Procedures (RAPs) that are used to diagnose image quality defect problems.

Section 4 Removal/Replacement and Adjustment Procedures

This section contains the removal, replacement, and adjustment procedures for components of WorkCentre 5016, 5020.

Section 5 Parts List

This section contains a list of spare parts list for the WorkCentre 5016, 5020.

Section 6 General Procedures/Information

This section contains frequently used procedures that relate to the diagnosis, setup, or opera-tion of the machine. It also contains pertinent information that will not be found in any other part of the service documentation.

Section 7 Wiring Data

This section contains the wiring information for the WorkCentre 5016, 5020. It contains a con-nector list/locator, wirenet diagrams, and Block Schematic Diagrams (BSDs) for the following chains:

Chain 1 Standby PowerChain 2 Mode SelectionChain 3 Machine Run ControlChain 4 Start Print PowerChain 6 ImagingChain 7 Paper SupplyingChain 8 Paper TransportationChain 9 MarkingChain 10 Fusing and Copy Transporta

Description of Terminology and The terminology and symbols used through

WA Warning statement indicates an opecondition that, if not strictly observed, c

CA Caution statement indicates an operatinthat, if not strictly observed, could result in

NOTE: A Note statement indicates an opertion that is necessary to accomplish a task

Reference:Used when other explanations are given.

Purpose:Used to describe the purposes of adjustme

REP:Indicates the removal/replacement procedu

ADJ:Indicates the adjustment procedure for refe

PL:Indicates the parts list for reference.

ASSY:Means Assembly.

Safety Critical Components (SCC):These are components, such as electrostathandled properly. Follow the regulations regCorp.


ivIntroduction

Service Call Procedures

vice Call ProceduresJune, 20081-1WorkCentre 5016, 5020

Reissue

1 Ser1.1 Before Starting Service ............................................................................................. 1-31.2 Service Call Procedure ............................................................................................. 1-41.3 Service Call Details ................................................................................................... 1-41.4 TRIM Checklist .......................................................................................................... 1-51.5 Periodic Replacement Parts/Consumables List ........................................................ 1-5


1-2Service Call Procedures

1.1Service Call Procedures

ing Customer Dataata.the purpose of investigation/analysis, always obtain ure you assure them that the data will not be used

changed during diagnostics.ch as polling, were set for test purposes, make sure s after the test.stomer data.ed within the OpCo and ensure that customer data e.

service, observe the following:

on, so that you can take a systematic approach.

dition of the machine before removing parts or dis-

omplete, check that no parts or tools are left inside

ables consumables, as well as the packaging materials,

WARNINGridges into a fire. Always keep them away from gniting and causing a fire.

methods for replaced parts or consumables, refer 2-138 for all machines.

g consumables, affix the "U-TAG" so that the recy-priately.

essary items on the "U-TAG."

mer's daily work.to a trash bag and bring it to the service office.ation in the Machine Service Log:

lacedJune, 20081-3WorkCentre 5016, 5020

Reissue

1.1 Before Starting Service1.1.1SafetyTo prevent any accident that may occur during maintenance service, any warning or any cau-tion regarding the service must be strictly observed. Do not perform any hazardous operation.

1. Power SupplyTo prevent electrical shocks, burns, or injury, etc., be sure to switch OFF the machine and disconnect the plug before starting the maintenance service. If the machine has to be switched ON, such as when measuring a voltage, take extra care to avoid an electrical shock.

2. Drive AreaNever inspect, clear or lubricate the drive components, such as chain belts, chain wheels or gears, when the machine is in operation.

3. Heavy PartsWhen removing or installing heavy parts, keep your back straight and lift with your legs. Some parts should not be lifted by one person:

IOT (Platen): 31.5kg (requires 3 persons)2 Tray Modules: 8.6kg (requires 2 persons)

Take extra care of your working posture to prevent backache.4. Safety Devices

See that safety devices for preventing accidents, such as fuses, circuit breakers, interlock switches, etc., and those for protecting customers from injury, such as panels and covers, function properly. Modifications that hinder the function of any safety devices are strictly prohibited.

5. Installing and Removing PartsThe edges of parts and covers may be sharp, so take care not to touch them. Be careful not to touch those parts, and wipe off any oil that may have adhered to your fingers or hands before servicing. When pulling out parts, cables, etc., do it gently. Do not use excessive force.

6. Specified ToolsFollow the instructions when a particular tool is specified.

7. Cleaning Up Toner SpillsSince toner can be explosive, sweep or brush any spilled toner into a container to collect it. To clean away the remaining toner using a vacuum cleaner, always use an FX standard vacuum cleaner that is toner-tolerant. Never use the customer's vacuum cleaner.

8. Earthquake Preparedness MeasuresIf the customer requests earthquake proofing, an earthquake preparedness kit is avail-able.Check the Service Guide for more information on the earthquake preparedness kit.

9. Modifications to the MachineBefore altering the machine, submit an irregular use license application.

10. Other Safety PrecautionsFollow the recommendations in WORKING PRACTICES FOR ENGINEERS issued by FXAP EH&S (Environmental Health and Safety).

1.1.2Things to Note When Handl1. Handling of copied/printed customer d

Before you bring back any sample for permission from the customer. Make sfor any other purpose.

2. Security-related NVM values that wereIf any security-related NVM values, suyou restore them to their original value

3. Other things to note when handling cuFollow the safety guidelines establishdo not get compromised during servic

1.1.3 Other PrecautionsTo avoid performing wrong or unnecessary

1. Reference MaterialsRead all relevant service documentati

2. DisassemblingMake sure to note the assembled conassembling it.

3. Installation and AdjustmentAfter the installation or adjustment is cthe machine.

4. Handling of replaced parts and consumMake sure that any replaced parts orare taken back to the Service Center.

Never discard the Drum/Toner Cartopen flames to prevent them from i

NOTE: For separation and processingto Common Technical Information No.

If you have replaced the followinclable parts will be handled approa. Drum Cartridgeb. Toner Cartridge

For recyclable parts, fill in the nec5. General Precautions

Take care not to disturb the custo Place any service-related trash in Clearly record the following inform

Details of the service call Parts and consumables rep


1.2 Service Call Procedure 1.3 Service Call Details

s condition. paper jams

he machine.e Log from the last call.f Problemtatus Indicator RAPs. 2 Status Indicator RAPs.leshoot by referring to the BSD in Section 7 Wiring

ttern (499T247), then check the quality.rform the applicable RAP in Section 3 Image Qual-

ance call.

ing the TRIM Checklist.c cleaning/replacement by referring to the TRIM ent Parts/Consumables List. Clean them if neces-nters of the corresponding items in the Chain Func-June, 20081-41.2, 1.3

Service Call Procedures

1.2.1 Initial Actions1. Ask the operator(s) about the machines condition.2. Record the billing meter readings.3. Inspect any faulty copies, then check the machine.4. Check the Service Log.1.2.2 Actions to Take During UM (Unscheduled Maintenance)1. Perform the service flow in Section 2 Status Indicator RAPs.2. Perform the applicable RAP in Section 2 Status Indicator RAPs.

If there are no applicable RAPs, troubleshoot by referring to the BSD in Section 7 Wiring Data.

3. Check the copy quality.Make several copies using the Test Pattern (499T247), then check the quality.

4. Look at the last 20 error codes in order to understand the machine status. Enter Diagnostic Mode. Enter [40-01] (Display Error History How to Enter the Diag-

nostic Mode). When the last error code is displayed, press the [Start] key to return to the Function

input screen. Pressing the [Stop] key during the display will stop it and return you to the Function

input screen.5. Repair all the secondary problems.6. Perform TRIM servicing.1.2.3 Actions to Take During SM (Scheduled Maintenance)1. Check the copy quality.

Make several copies using the Test Pattern (499T247), then check the quality.2. Look at the last 20 error codes in order to understand the machine status.

Enter Diagnostic Mode. Enter [40-01] (Display Error History How to Enter the Diag-nostic Mode).

When the last error code is displayed, press the [Start] key to return to the Function input screen.

Pressing the [Stop] key during the display will stop it and return you to the Function input screen.

3. Perform TRIM servicing.1.2.4 Final Actions1. Check overall machine operation/features.2. Check the machine exterior and consumables.3. Train the operator as required.4. Complete the Service Log and Service Report.5. Keep the copy samples with the Service Log.

1.3.1 Initial Actions1. Ask the operator(s) about the machine

Frequency and location of recent Copy quality

2. Record the billing meter readings.3. Inspect any faulty copies, then check t4. Check the copy sample and the Servic1.3.2 Checking Reproducibility o1. Perform the service flow in Section 2 S2. Perform the applicable RAP in Section3. If there are no applicable RAPs, troub

Data.1.3.3 Checking Copy Quality1. Make several copies using the Test Pa2. If there is a problem in copy quality, pe

ity.1.3.4 TRIM ServicingPerform TRIM servicing during the mainten

1. Perform the necessary TRIM items us2. Check for parts that require periodi

Checklist and the Periodic Replacemsary. If replaced, always clear the coution.

1.4, 1.5Service Call Procedures

arts/Consumables Listmber of copies and the replacement interval for the ical cleaning/replacement. Clean or replace them if d at Chain-Function > NVRAM R/W, while the IIT er to Diagnostic Mode in Section 2 Status Indicator in the Diagnostic Mode, clean or replace them dard PV).

AUTIONour car for long periods of time.

Table 1 nt pies) Counters Check

[29/34] [29/24] [29/14] [29/4]Count up 1 for every feed. Replace both at the same time. [29/25] [29/15] [29/5]Count up 1 for every feed. Replace both at the same time. [29/39] [29/29] [29/19] [29/9]Count up 1 for every feed. Replace both at the same time.[21/39] [21/29] [21/19] [21/9]Count up 1 for every feed.

31,000 (Warning)36,000 (Machine Stops)June, 20081-5WorkCentre 5016, 5020

Reissue

1.4 TRIM ChecklistA: Check. Clean, replace, or replenish if necessary.

B: Always check and clean.

*: Always replace at the specified interval.

CAUTIONDo not touch the Drum of the Drum Cartridge.

1.5 Periodic Replacement PWhen servicing the machine, check the nuconsumables and parts that require periodnecessary. The IOT history can be checkehistory can be checked in the Counters (refRAPs). For items that cannot be checkedaccording to the replacement intervals (stan

CDo not keep toner and drum cartridges in y

Table 1

No. Service ItemsEvery time Service Details

1.1 Check before servicing(check machine operation)

A Turn on the machine, and make sure that there are no abnormal sounds.

1.2 Check before Servicing(copy the Test Pattern)

A Make several copies using the Test Pattern (499T247), then check the image quality.

2 Clean the interior of the machine (paper transport system)

A Clean the paper dust and toner residue in the paper path and on the jam sensor.

3 Clean the IIT A Clean the Platen Glass surface and the Platen Cushion with the optical cleaning cloth.

Clean the Reflector, back of the Platen Glass, mirrors and lens with the optical cleaning cloth.

5 Safety Precautions B Make sure that the power cord is plugged in properly.

Make sure that there are no cracks in the power plug and no holes or cuts in the power cord insulation.

If an extension cord or power strip is used, make sure it is of sufficient capacity to handle the power requirements of the machine.

Make sure that no more than one power plug is connected to a single socket.

6.1 Check after servicing(copy quality check)

A Make several copies using the Test Pattern (499T247), then check the image quality.

6.2 Check after servicing(check machine operation)

A Check the paper feed. Make sure that there are no abnormal sounds.

6.3 Check after servicing(check the meter)

A Create the Service Log and Service Report.

NoParts/Consumables Name/PL No.

ReplacemeInterval (co

1 Tray 1 Feed Roll/ Retard Pad

50,000

2 Tray 2 Feed Roll/Retard Roll

100,000

3 MSI Feed Roll/Retard Pad

50,000

4 Fuser Unit 100,000

5 Toner Cartridge 6,0006 Drum Cartridge 36,000


1-61.4, 1.5Service Call Procedures

Status Indicator RAPS

tatus Indicator RAPSJune, 20082-1WorkCentre 5016, 5020

Reissue

2 S Error CodesFault Repair Overview and List of Error Codes............................................................... 2-3

RAPsU0-1 Main Motor Stop Error ............................................................................................ 2-25U1-1 Main Motor Rotation Error ...................................................................................... 2-25U2-1 Carriage Module Fail .............................................................................................. 2-26U3-5 Laser Power Or ROS Motor Fail ........................................................................... 2-26U4-1 Fuser On Time Fail................................................................................................ 2-27U4-2 Over Heat Temp Fail ............................................................................................. 2-27U4-3 FS1 Thermistor Defect .......................................................................................... 2-28U4-9 Fuser Fan Defect................................................................................................... 2-28U6-2 RAM Read/Write Check Error ............................................................................... 2-29U6-3 NVM Data Defect .................................................................................................. 2-29U6-4 NVM Read/Write Cannot Be Executed ................................................................. 2-30U6-5 CPU Power To Access NVM Is Not Enough ......................................................... 2-30U7-0 UI Communication TimeOut .................................................................................. 2-31U7-1 UI Communication Error........................................................................................ 2-31U8-1 Billing Counter Defect............................................................................................ 2-32U9-0 HVPS Fail .............................................................................................................. 2-32062-300 Platen Interlock Open ....................................................................................... 2-33062-345 IISS EEPROM Failure....................................................................................... 2-33062-360 Carriage Position Fail........................................................................................ 2-34062-371 Lamp Illumination Fail ....................................................................................... 2-34062-380 AGC Failure ...................................................................................................... 2-35062-386 AOC Failure ...................................................................................................... 2-35062-392 IPS PWB Memory Fail ...................................................................................... 2-36062-393 IPS PWB Fail .................................................................................................... 2-36005-170 DADF Feed Failure ........................................................................................... 2-37005-171 DADF Regi / Exit Failure.................................................................................. 2-38005-172 DADF Inverted Document Jam ......................................................................... 2-39005-198 Short Scan Jam ................................................................................................ 2-40005-199 Long Scan Jam ................................................................................................. 2-40005-305 Feeder Top Cover Open ................................................................................... 2-41005-920 Static Jam ......................................................................................................... 2-41


2-2Status Indicator RAPS

Status Indicator RAPSJune, 20082-3WorkCentre 5016, 5020

Reissue

Fault Repair Overview and List of Error CodesFault Repair OverviewThe fault repair operation proceeds in the following flow. After performing the pre-check, verify the symptoms and refer to the Error Code List and Section 7 Wiring Data to effectively repair the fault:

.

Figure 1 Troubleshooting Procedure

Check the status of Installation

Check the problem status

Perform RAP

Check if the fault is repaired

Completed

Diagnostic ModeOperating PrinciplesWiring Data

Reference Information


Check the Status of Installation Descriptions related to connectors are expressed as follows: P/J12" -> The connector (P/J12) is in the connected state. "P12" -> The plug side when the connector (P/J12) is in the

directly connected to a board). "J12" -> The jack the disconnected state (except when it is directly

t all the opposing pins between "P/J1" and "P/J12" d be measured.e measured using a special tool. Handle the tool

RAPs are for reference only. Approximate values

e RAP, you must check the references for the parts ures.

the parts that are considered to be the cause of the and, if necessary, the assembly that contains those

supply is called "Tray 1," and the one below it is

cribed separately for each specification. Follow the e faults.

ing a failure. RAPs guide you through the trouble-nce of error codes and other types of problematic d to image quality, refer to Section 3 Image Quality June, 20082-4


Before starting to troubleshoot, always check the following items:

The voltage of the power supply (measure the voltage at the power outlet to see if it is within specification).

The power cord for damage, short circuits, open circuits, and wrong internal connections. The machine for proper grounding. The machine is not installed in a place with high temperature, high humidity, low tempera-

ture, low humidity, or a place with drastic changes in temperature. The machine is not installed near a water outlet, humidifier, heater or fire source, dusty

areas, or under the direct draft of an air conditioner. The machine is not installed in a place where volatile or flammable gas is generated. The machine is not installed in a place exposed to direct sunlight. The machine is installed in a well-ventilated place. The machine is installed on a stable level surface. The paper is within specification (standard paper is recommended). The machine for any improper handling. The Periodic Replacement Parts are replaced at the proper intervals.Safety Considerations Before servicing, always unplug the power cord unless required otherwise. When the

power is turned ON, never touch a current-carrying part unless required otherwise. Also, since current is carried in the LVPS power switch/inlet even when the power is turned OFF, never touch this area.

When turning the power ON to perform a check while the Interlock Switch or Security Switch is also turned ON and the covers are removed, always disconnect the connector ( P/J140) that is connected to the ROS, unless required otherwise, because a laser beam might be emitted from the ROS.

When connecting the connector ( P/J520) on the HVPS according to the instructions in the RAP, never touch the HVPS and high-voltage output parts.

When performing a high voltage output check using the Input Diagnostics or Output Diag-nostics in Diagnostic Mode, make sure that all covers are installed unless specified other-wise. Also, never touch any high voltage output section when performing the high voltage output check.

When operating the Drive Section using the Input Diagnostics or Output Diagnostics in Diagnostic Mode, make sure that all covers are installed unless specified otherwise. Also, never touch the Drive Section while operating it.

Be careful not to burn yourself when touching parts that can get very hot. When servicing, use a grounded wrist band to remove static electricity from your body.Things to Note When Using RAPs When troubleshooting using RAPs, prepare normally working parts such as the AIOC

PWB, LVPS, HVPS and Fuser in advance because they might be required to identify a failure. In addition, if the fault cannot be repaired, replace the "parts considered to be the cause" and related parts in sequence and check the operation.

When servicing, always disconnect the power cord unless required otherwise. When the power cord is connected, never touch any current-carrying part unless absolutely neces-sary.

disconnected state (except when it isside when the connector (P/J12) is inconnected to a board).

In a RAP, "P/J1 P/J2" means tha(refer to Section 7, Wiring Data) shoul

The voltages on small connectors arcarefully because it has a sharp tip.

The numerical values described in theare considered to be the same.

Note that for the checks specified in ththat must be removed and their proced

"Replacement" in the RAPs indicates problem. Check by replacing the partsparts.

In the RAPs, the highest level papercalled "Tray 2."

In the RAPs, some procedures are desinstructions for your model to repair th

RAP FlowRAPs are a good place to start in diagnosshooting process by checking for the presesymptoms. To troubleshoot problems relateTroubleshooting.


orm the June, 20082-5WorkCentre 5016, 5020

Reissue

Figure 2 RAP Flow

Ask the operator about the problemDid the operator operate the machine correctly?

Turn the Power Switch OFF then ON

Does the error recur when operating the machine in the same way as before (when the problem originally occurred)?

Does the Control Panel display an Error Code?

Explain how to operate the machine

Procedure is complete

Refer to the Error Code List and perfrelevant troubleshooting

Yes

No

Yes

No

Yes


Error Code List

Record in Error Log RAP BSD

eed Sensor

O - CH8.1Figure 1June, 20082-6


NOTE: In the Record in Error Log column, O = yes and X = no.

Error Code Error Name/Explanation/I/O Diagnostic Codes/Check Items

C1-1

Error NameTray1 F/O#1 SNR on JAM

ExplanationTimeout between Tray1 Feed Clutch ON and Tray1 Feed Sensor ON.

I/O Diagnostic Codes (How to Enter the Diagnostic Mode) [08-07] Tray1 Feed Sensor [08-12] Tray1 Feed ClutchCheck Items Feed Roll or Retard Pad dirty, contaminated with paper dust, worn, or faulty Tray1 Feed Sensor dirty and Sensor Actuator deformed or damaged Paper damaged, not within specification, or not loaded correctly Foreign matter, burrs, or paper in the paper path Drive gear worn or damaged Tray1 Feed Clutch faulty Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the Tray 1 F

(PL 2.5)(REP 2.5.1). Wire between Tray 1 Feed Sensor J158-3 ( P/J158) and LVPS J501-6 ( P/J501) Wire between Tray 1 Feed Sensor J158-2 and LVPS J501-7 Wire between Tray 1 Feed Sensor J158-1 and LVPS J501-8

Replace the Tray1 Feed Clutch (PL 2.2) (REP 2.2.1) and the AIOC PWB (PL 8.1) (REP 8.1.1) in that order.


eed Sensor

stration Sen-

O -

CH8.1Figure 1CH8.4

Figure 4

Record in Error Log RAP BSDJune, 20082-7WorkCentre 5016, 5020

Reissue

C1-2

Error NameTray1 Regi SNR on JAM

ExplanationTimeout between Tray1 Feed Sensor ON and IOT Registration Sensor ON.

I/O Diagnostic Codes (How to Enter the Diagnostic Mode) [08-07] Tray1 Feed Sensor [08-05] IOT Registration Sensor [08-10] IOT Registration ClutchCheck Items Take Away Roll 1 dirty, contaminated with paper dust, worn, or faulty Tray1 Feed Sensor dirty and Sensor Actuator deformed or damaged Paper damaged, not within specification, or not loaded correctly Foreign matter, burrs, or paper in the paper path Drive gear worn or damaged IOT Registration Clutch faulty Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the Tray 1 F

(PL 2.5) (REP 2.5.1). Wire between Tray 1 Feed Sensor J158-3 ( P/J158) and LVPS J501-6 ( P/J501) Wire between Tray 1 Feed Sensor J158-2 and LVPS J501-7 Wire between Tray 1 Feed Sensor J158-1 and LVPS J501-8

Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the IOT Regisor (PL 2.9). - Wire between IOT Registration Sensor J156-3 ( P/J156) and LVPS J503-1 ( P/J503)- Wire between IOT Registration Sensor J156-2 and LVPS J503-2 - Wire between IOT Registration Sensor J156-1 and LVPS J503-3

Replace the IOT Registration Clutch (PL 2.9) and the AIOC PWB (PL 8.1) (REP 8.1.1) in that order.



Sensor (PL

.5) (REP

O - CH8.2Figure 2

Error Record in Error Log RAP BSDJune, 20082-8


C2-1

Error NameSTM F/O#2 SNR on JAM

ExplanationTimeout between STM Feed Motor ON and STM Feed Sensor ON.

I/O Diagnostic Codes (How to Enter the Diagnostic Mode) [08-06] STM Feed Sensor [08-11] STM Feed Clutch [08-13] STM Feed MotorCheck Items Tray2 Feed Roll or Tray2 Retard Roll dirty, contaminated with paper dust, worn, or faulty STM Feed Sensor dirty and Sensor Actuator deformed or damaged Paper damaged, not within specification, or not loaded correctly Foreign matter, burrs, or paper in the paper path Drive gear worn or damaged STM Feed Clutch faulty STM Feed Motor faulty Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the STM Feed

11.5) (REP 11.5.1 ). - Wire between STM Feed Sensor J172-3 ( P/J172) and STM PWB J542-6 ( P/J542) - Wire between STM Feed Sensor J172-2 and STM PWB J542-7 - Wire between STM Feed Sensor J172-1 and STM PWB J542-8

Replace the STM Feed Clutch (PL 11.6) (REP 11.6.1), the STM Feed Motor (PL 11.6) (REP 11.6.2), and the STM PWB (PL 1111.5.2 ) in that order.

Code Error Name/Explanation/I/O Diagnostic Codes/Check Items


Sensor (PL

eed Sensor

.5) (REP

O -

CH8.1Figure 1CH8.2

Figure 2


Reissue

C2-2

Error NameTray1 F/O#1 SNR on JAM from STM feed

ExplanationTimeout between STM Feed Out Sensor ON and Tray 1 Feed Out Sensor ON.

I/O Diagnostic Codes (How to Enter the Diagnostic Mode) [08-06] STM Feed Sensor [08-07] Tray1 Feed Sensor [08-11] STM Feed Clutch [08-13] STM Feed MotorCheck Items Take Away Roll 2 dirty, contaminated with paper dust, worn, or faulty STM Feed Sensor dirty and Sensor Actuator deformed or damaged Paper damaged, not within specification, or not loaded correctly Foreign matter, burrs, or paper in the paper path Drive gear worn or damaged STM Feed Clutch faulty STM Feed Motor faulty Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the STM Feed

11.5) (REP 11.5.1). Wire between STM Feed Sensor J172-3 ( P/J172) and STM PWB J542-6 ( P/J542) Wire between STM Feed Sensor J172-2 and STM PWB J542-7 Wire between STM Feed Sensor J172-1 and STM PWB J542-8

Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the Tray 1 F(PL 2.5) (REP 2.5.1). Wire between Tray 1 Feed Sensor J158-3 ( P/J158) and STM PWB J501-6 ( P/J501) Wire between Tray 1 Feed Sensor J158-2 and STM PWB J501-7 Wire between Tray 1 Feed Sensor J158-1 and STM PWB J501-8

Replace the STM Feed Clutch (PL 11.6) (REP 11.6.1), the STM Feed Motor (PL 11.6) (REP 11.6.2), and the STM PWB (PL 1111.5.2) in that order.



eed Sensor

stration Sen-

O -

CH8.1Figure 1CH8.4

Figure 4

e job).

Paper Sen-

X - CH7.1Figure 1



C2-3

Error NameSTM Regi SNR on JAM

Explanation When feeding paper from the STM, timeout between Tray1 Feed Sensor ON and IOT Registration Sensor ON.I/O Diagnostic Codes (How to Enter the Diagnostic Mode) [08-05] IOT Registration Sensor [08-10] IOT Registration Clutch Check Items Take Away Roll 1 dirty, contaminated with paper dust, worn, or faulty IOT Registration Sensor dirty and Sensor Actuator deformed or damaged Paper damaged, not within specification, or not loaded correctly Foreign matter, burrs, or paper in the paper path Drive gear worn or damaged IOT Registration Clutch faulty Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the Tray 1 F

(PL 2.5) (REP 2.5.1). Wire between Tray 1 Feed Sensor J158-3 ( P/J158) and LVPS J501-6 ( P/J502) Wire between Tray 1 Feed Sensor J158-2 and LVPS J501-7 Wire between Tray 1 Feed Sensor J158-1 and LVPS J501-8

Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the IOT Regisor (PL 2.9). Wire between Tray 1 Feed Sensor J156-3 ( P/J156) and LVPS J503-1 ( P/J503) Wire between Tray 1 Feed Sensor J156-2 and LVPS J503-2 Wire between Tray 1 Feed Sensor J156-1 and LVPS J503-3

Replace the IOT Registration Clutch (PL 2.9) and the AIOC PWB (PL 8.1) (REP 8.1.1) in that order.

C5-0

Error NameNo paper in the selected paper tray (Tray1)

Explanation No paper is detected in Tray1 when ATS function is disabled and Tray1 is selected during a copy job. No paper is detected in Tray1 when Tray1 is selected during a print job (the paper size setting matches the one specified for thI/O Diagnostic Codes

[07-07] Tray1 No Paper SensorCheck Items Press the [Stop] button on the Control Panel. Check the tray to see if it is empty; if it is, add paper specified by the job. Tray1 No Paper Sensor dirty and Sensor Actuator deformed or damaged Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the Tray 1 No

sor (PL 2.7) (REP 2.7.1). Wire between Tray1 No Paper Sensor J157-3 ( P/J157) and LVPS J501-3 ( P/J501) Wire between Tray1 No Paper Sensor J157-2 and LVPS J501-4 Wire between Tray1 No Paper Sensor J157-1 and LVPS J501-5

Replace the AIOC PWB (PL 8.1) (REP 8.1.1).



X - -

the job).

Paper Sen-

X - CH7.2Figure 2

b. X - -

. X - -


Reissue

C5-1

Error NameTray1 Paper Size Mismatch

Explanation Paper that is different from the one in the Tray Settings is detected when feeding. Or, paper size setting in Tray1 is different from the paper size specification of the job when Tray1 is selected during a print job.Check Items Press the [Stop] button on the Control Panel. Change the paper size of Tray 1 to the one specified by the job.

C6-0

Error NameNo paper in the selected paper tray (Tray2)

Explanation No paper is detected in the STM when ATS function is disabled and STM is selected during a copy job. No paper is detected in the STM when STM is selected during a print job (the paper size setting matches the one specified forI/O Diagnostic Codes (How to Enter the Diagnostic Mode)

[07-08] STM No Paper SensorCheck Items Press the [Stop] button on the Control Panel. Load the correct paper into the STM. STM No Paper Sensor dirty and Sensor Actuator deformed or damaged. Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the STM No

sor (PL 11.7) (REP 11.7.1). Wire between STM No Paper Sensor J171-3 ( P/J171) and STM PWB J542-3 ( P/J542) Wire between STM No Paper Sensor J171-2 and STM PWB J542-4 Wire between STM No Paper Sensor J171-1 and STM PWB J542-5

Replace the STM PWB (PL 11.5) (REP 11.5.2) and the AIOC PWB (PL 8.1) (REP 8.1.1).

C6-1

Error NameTray2 Paper Size Mismatch

Explanation Paper that is different from the one in the Tray Settings is detected when feeding. Or, paper size setting in the STM is different from the paper size specification of the job when STM is selected during a print joCheck Items Press the [Stop] button on the Control Panel. Change the paper size of STM to the one specified by the job.

C7-1

Error NameMSI Paper Size Mismatch

Explanation Paper that is different from the one in the Tray Settings is detected when feeding. Or, paper size setting in the MSI is different from the paper size specification of the job when MSI is selected during a print jobCheck Items Press the [Stop] button on the Control Panel. Change the paper size of Bypass to the one specified by the job.



g a copy job.uring a print X - CH3.2Figure 2

stration Sen-

there is no

O -

CH8.3Figure 3CH8.4

Figure 4



C0-1

Error NameAPS NG Unselected

Explanation Either Tray 1 or STM is in one of the "paper settings is of a size that causes missing image" states when APS is selected durin Or, either Tray 1 or STM is "set with paper size that is different from the one specified for the job" when Auto Tray is selected d

job.Check Items Press the [Stop] button on the Control Panel. Change the paper size of Tray 1 or STM to the one specified by the job.

C9-3

Error NameMSI Regi SNR on JAM

ExplanationTimeout between Bypass Solenoid ON and IOT Registration Sensor ON.

I/O Diagnostic Codes (How to Enter the Diagnostic Mode) [08-05] IOT Registration Sensor [08-17] Bypass SolenoidCheck Items Bypass Feed Roll, Retard Pad, or Bypass Take Away Roll dirty, contaminated with paper dust, worn, or faulty IOT Registration Sensor dirty and Sensor Actuator deformed or damaged Paper damaged, not within specification, or not loaded correctly Foreign matter, burrs, or paper in the paper path Drive gear worn or damaged Bypass Solenoid faulty Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the IOT Regi

sor (PL 2.9). Wire between Tray 1 Feed Sensor J156-3 ( P/J156) and LVPS J503-1 ( P/J503) Wire between Tray 1 Feed Sensor J156-2 and LVPS J503-2 Wire between Tray 1 Feed Sensor J156-1 and LVPS J503-3

Check that the Bypass Solenoid and the LVPS J502-1/3 ( P/J502) pins are connected securely with good electrical contact. If problem, replace the Bypass Solenoid (PL 7.5).




eed Sensor

O - CH8.1Figure 1

Sensor (PL

O - CH8.2Figure 2

eleted. O - -


Reissue

C8-1

Error NameF/O#1 SNR Static JAM

ExplanationTray1 Feed Sensor ON is detected during standby.

I/O Diagnostic Codes (How to Enter the Diagnostic Mode)[08-07] Tray1 Feed Sensor

Check Items Tray1 Feed Sensor dirty and Sensor Actuator deformed or damaged Foreign matter, burrs, or paper in the paper path Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the Tray 1 F

(PL 2.5) (REP 2.5.1). Wire between Tray 1 Feed Sensor J158-3 ( P/J158) and STM PWB J501-6 ( P/J501) Wire between Tray 1 Feed Sensor J158-2 and STM PWB J501-7 Wire between Tray 1 Feed Sensor J158-1 and STM PWB J501-8


C8-2

Error NameF/O#2 SNR Static JAM

ExplanationSTM Feed Sensor ON is detected during standby.

I/O Diagnostic Codes (How to Enter the Diagnostic Mode)[08-06] STM Feed Sensor

Check Items STM Feed Sensor dirty and Sensor Actuator deformed or damaged Foreign matter, burrs, or paper in the paper path Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the STM Feed

11.5) (REP 11.5.1). Wire between STM Feed Sensor J172-3 ( P/J172) and STM PWB J542-6 ( P/J542) Wire between STM Feed Sensor J172-2 and STM PWB J542-7 Wire between STM Feed Sensor J172-1 and STM PWB J542-8

Replace the STM PWB (PL 11.5) (REP 11.5.2) and the AIOC PWB (PL 8.1) (REP 8.1.1) in that order.

E0-1

Error NameCPM Image Lost

ExplanationDuring a copy job in CMP Priority Mode, it is detected that the paper containing an image cannot be output after the image is d

Check ItemsPress the [Stop] button on the Control Panel.



stration Sen-

O - CH8.4Figure 4

t Sensor (PL

O - CH10.2Figure 2



E1-6

Error NameRegi SNR Static JAM

ExplanationIOT Registration Sensor ON is detected during standby.

I/O Diagnostic Codes (How to Enter the Diagnostic Mode)[08-05] IOT Registration Sensor

Check Items Sensor dirty Foreign matter, burrs, or paper in the paper path Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the IOT Regi

sor (PL 2.9). Wire between Tray 1 Feed Sensor J156-3 ( P/J156) and LVPS J503-1 ( P/J503) Wire between Tray 1 Feed Sensor J156-2 and LVPS J503-2 Wire between Tray 1 Feed Sensor J156-1 and LVPS J503-3

Replace the AIOC PWB (PL 8.1)(REP 8.1.1).

E3-6

Error NameExit SNR JAM

ExplanationFuser Exit Sensor ON is detected during standby.

I/O Diagnostic Codes (How to Enter the Diagnostic Mode)[10-23] Fuser Exit Sensor

Check Items Fuser Exit Sensor dirty and Sensor Actuator deformed or damaged Foreign matter, burrs, or paper in the paper path Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the Fuser Exi

6.2). Wire between Fuser Exit Sensor J153-3 ( P/J153) and LVPS J505-1 ( P/J505) Wire between Fuser Exit Sensor J153-2 and LVPS J505-2 Wire between Fuser Exit Sensor J153-1 and LVPS J505-3




r Interlock

X - CH1.2Figure 2

ver Interlock

X - CH1.2Figure 2

terlock

X - CH7.1Figure 1


Reissue

E5-1

Error NameIOT L/H Cover open

ExplanationThe Left Hand Cover is open.

I/O Diagnostic Codes (How to Enter the Diagnostic Mode)[01-01] LH Cover Interlock Switch

Check Items Check that the Left Hand Cover closes correctly. Check that the LH Cover Interlock Switch is correctly installed and that the electrical connection is good. Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the LH Cove

Switch (PL 8.2). Wire between LH Cover Interlock Switch FS151 ( FS151) and LVPS J506-4 ( P/J506) Wire between LH Cover Interlock Switch FS152 ( FS152) and LVPS J506-3

Replace the LVPS (PL 8.1) (REP 8.1.2) and the AIOC PWB (PL 8.1) (REP 8.1.1) in that order.

E5-2

Error NameIOT Front Cover open

ExplanationThe Front Cover is open.

I/O Diagnostic Codes (How to Enter the Diagnostic Mode)[01-12] Front Cover Interlock Switch

Check Items Check that the Front Cover closes correctly. Check that the Front Cover Interlock Switch is correctly installed and that the electrical connection is good. Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the Front Co

Switch (PL 8.2). Wire between Front Cover Interlock Switch FS153 ( FS153) and LVPS J506-2 ( P/J506) Wire between Front Cover Interlock Switch FS154 ( FS154) and LVPS J506-1


E6-1

Error NameL/H Low Cover open

ExplanationAccess Cover 1 is open.

I/O Diagnostic Codes (How to Enter the Diagnostic Mode)[01-11] Tray1 Interlock Switch

Check Items Check that Access Cover 1 closes correctly. Check that the Tray 1 Interlock Switch is correctly installed and that the electrical connection is good. Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the Tray 1 In

Switch (PL 2.5). Wire between Tray 1 Interlock Switch J161-2 ( P/J161) and LVPS J501-9 ( P/J501) Wire between Tray 1 Interlock Switch J161-1 and LVPS J501-10




rlock Switch

t order.

X - CH7.2Figure 2

X - CH3.2Figure 2

X - CH3.2Figure 2



E6-2

Error NameSTM L/H Cover open

ExplanationAccess Cover 2 is open.

I/O Diagnostic Codes (How to Enter the Diagnostic Mode)[01-10] STM Interlock Switch

Check Items Check that Access Cover 2 closes correctly. Check that the STM Interlock Switch is correctly installed and that the electrical connection is good. Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the STM Inte

(PL 11.5). Wire between STM Interlock Switch J173-2 ( P/J173) and STM PWB J542-9 ( P/J542) Wire between STM Interlock Switch J173-1 and STM PWB J542-10

Replace the STM PWB (PL 11.5) (REP 11.5.2), the LVPS (PL 8.1) (REP 8.1.2), and the AIOC PWB (PL 8.1) (REP 8.1.1) in tha

E8-1

Error NameNup NG Out Of Range

ExplanationThe magnification is not within the range of 50 to 200% during Nup.

Check Items Press the [Stop] button on the Control Panel. Press the [Paper Supply] button on the Control Panel. Press the [Special Copy] button on the Control Panel. Press the [Original Size Input] button on the Control Panel. Press the [Clear All] button on the Control Panel.

E8-2

Error NameNup Paper direction mismatch

ExplanationThe paper orientation of the document and the tray are not aligned during Nup.

Check Items Press the [Stop] button on the Control Panel. Press the [Paper Supply] button on the Control Panel. Press the [Special Copy] button on the Control Panel. Press the [Original Size Input] button on the Control Panel. Press the [Clear All] button on the Control Panel.



ct. If there is

t Sensor (PL

O - CH10.2Figure 2

t Sensor (PL

O - CH10.2Figure 2


Reissue

E1-2

Error NameExit SNR on JAM

ExplanationTimeout between IOT Registration Clutch ON and Fuser Exit Sensor ON.

I/O Diagnostic Codes (How to Enter the Diagnostic Mode) [08-10] IOT Registration Clutch [10-23] Fuser Exit SensorCheck Items Registration Roll dirty, contaminated with paper dust, worn, or faulty Fuser Exit Sensor dirty and Sensor Actuator deformed or damaged Paper damaged or not within specification Foreign matter, burrs, or paper in the paper path Drive gear worn or damaged IOT Registration Clutch faulty Check that the IOT Registration Clutch and the LVPS J503-4/5 ( P/J503) pins are connected securely with good electrical conta

no problem, replace the IOT Registration Clutch (PL 2.9). Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the Fuser Exi



E3-1

Error NameExit SNR off JAM

ExplanationTimeout between Fuser Exit Sensor ON and Fuser Exit Sensor OFF.

I/O Diagnostic Codes (How to Enter the Diagnostic Mode)[10-23] Fuser Exit Sensor

Check Items Fuser Exit Sensor dirty and Sensor Actuator deformed or damaged Paper damaged or not within specification Foreign matter, burrs, or paper in the paper path Drive gear worn or damaged Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the Fuser Exi





O - CH3.1Figure 1

X - CH3.2Figure 2

If there is no

X - -

t. If there is

O - CH9.2Figure 2



H9-7

Error Name MCU-STM comm. errorExplanation

A communication failure has occurred between the MCU and the Tray Module.Check Items Turn the power OFF then ON. Check for any open circuit or short circuit between the STM connectors. Replace the STM PWB (PL 11.5) (REP 11.5.2) and the AIOC PWB (PL 8.1) (REP 8.1.1) in that order.

L9-0

Error NameCopy Counter Full

ExplanationThe user that is logged in has reached the allotted copy limit in the Account Mode.


J1-0

Error NameToner Cartridge was PRENEAR empty

ExplanationThe toner cartridge is low.

Check Items Refill the toner. Foreign matter on the sensor. Check that the Toner Empty Sensor and the LVPS J509-1-4 ( P/J509) pins are connected securely with good electrical contact.

problem, replace the Toner Empty Sensor (PL 4.2). Replace the AIOC PWB (PL 8.1) (REP 8.1.1).

J1-2

Error NameToner Empty

ExplanationThe Toner Cartridge is empty.

I/O Diagnostic Codes (How to Enter the Diagnostic Mode)[09-07] Toner Empty Sensor

Check Items Refill the toner. Foreign matter on the sensor. Check that the Toner Empty Sensor and the LVPS J509 ( P/J509) 1-4 pins are connected securely with good electrical contac

no problem, replace the Toner Empty Sensor (PL 4.2). Replace the AIOC PWB (PL 8.1) (REP 8.1.1).



rtridge (PL O - CH9.2Figure 2

X - -

O - -


Reissue

J3-1

Error NameNo Drum Cartridge

ExplanationUnable to detect the Drum Cartridge.

I/O Diagnostic Codes (How to Enter the Diagnostic Mode)[09-02] Drum Cartridge

Check Items Turn the power OFF then ON. Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the Drum Ca

4.1) (REP 4.1.1). Wire between Drum Cartridge P610-7 ( P610) and AIOC PWB J402-1 ( P/J402) Wire between Drum Cartridge P610-3 and AIOC PWB J402-4 Wire between Drum Cartridge P610-2 and AIOC PWB J402-5 Wire between Drum Cartridge P610-5 and AIOC PWB J402-2 Wire between Drum Cartridge P610-4 and AIOC PWB J402-3 Wire between Drum Cartridge P610-1 and AIOC PWB J402-6

Replace the Drum Cartridge (PL 4.1) (REP 4.1.1) and the AIOC PWB (PL 8.1) (REP 8.1.1) in that order.

J6-0

Error NameDrum near end of life

ExplanationThe Drum Cartridge is near the end of its life.

Check ItemsReplace the Drum Cartridge (PL 4.1) (REP 4.1.1).

J6-1

Error NameDrum cartridge life end

ExplanationThe Drum Cartridge has reached the end of its life.

Check ItemsReplace the Drum Cartridge (PL 4.1) (REP 4.1.1).



rtridge (PL O - CH9.2Figure 2

O - CH9.2Figure 2

O - CH9.2Figure 2

O - -



J7-1

Error NameDrum CRUM comm. Error

ExplanationThe AIOC PWB is unable to communicate with the Drum Cartridge.

I/O Diagnostic Codes (How to Enter the Diagnostic Mode) [09-02] Drum CartridgeCheck Items Turn the power OFF then ON. Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the Drum Ca

4.1) (REP 4.1.1). Wire between Drum Cartridge P610-7 ( P610) and AIOC PWB J402-1 ( P/J402) Wire between Drum Cartridge P610-3 and AIOC PWB J402-4 Wire between Drum Cartridge P610-2 and AIOC PWB J402-5 Wire between Drum Cartridge P610-5 and AIOC PWB J402-2 Wire between Drum Cartridge P610-4 and AIOC PWB J402-3 Wire between Drum Cartridge P610-1 and AIOC PWB J402-6

Replace the Drum Cartridge (PL 4.1) (REP 4.1.1) and the AIOC PWB (PL 8.1) (REP 8.1.1) in that order.

J7-2

Error NameDrum CRUM Market Identity Mismatch

ExplanationThe AIOC PWB has detected that the Drum CRUM destination does not match.

Check Items Turn the power OFF then ON. Replace the Drum Cartridge (PL 4.1) (REP 4.1.1).

J7-3

Error NameDrum CRUM ID error

Explanation The AIOC PWB has detected that the Drum CRUM ID is incorrect.Check Items Turn the power OFF then ON. Replace the Drum Cartridge (PL 4.1) (REP 4.1.1).

N1-1

Error NameEPC Memory Full

Explanation During a copy job in Collate Mode, the EPC memory is full. Or, the machine has reached a state where it is unable to scan in any more documents.Check Items

Press the [Stop] button on the Control Panel.



O - CH3.2Figure 2

O - CH3.2Figure 2

-

-

O - -

O - -


Reissue

N4-0

Error NameNo Response from USB-Host

Explanation Either "USB disconnected" or "Communication timed-out" is detected during a print job. Or, either "USB disconnected" or "Communication timed-out" is detected during a scan job. Check Items Cancel the print job. Reconnect the USB cable correctly.

N4-1

Error NameHBPL or XPJL Syntax Error

ExplanationAn abnormal command that cannot be ignored is received from the USB-Host during a print job.

Check Items Cancel the print job. Reconnect the USB cable correctly.

N4-2

Error NameDownload File Error

ExplanationThere is an abnormal Product ID or there is a checksum error in the download file.


N4-3

Error NameDownload Flash Write Error

ExplanationUnable to write the downloaded file into flash memory.


E0-1

Error NameCPM Image Lost

ExplanationDuring a copy job in CPM Priority Mode, the paper containing an image cannot be output after the image is deleted.


N5-0

Error NamePush Scan TimeOut

Explanation Push scan notification failed during a scan job. Or, there is no scan job request from the PC after a push scan notification.Check Items

The error will clear itself after a set amount of time has passed.



O - CH3.2Figure 2

O - CH3.2Figure 2

O U0-1 CH4.1Figure 1









N9-0

Error NameController Logic fail

ExplanationA software defect that cannot be ignored is found in the Controller software.

Check ItemsTurn the power OFF then ON.

N9-1

Error NameIOT Communication Error

ExplanationThe AIOC PWB has detected a Type-Di communication error.

Check ItemsTurn the power OFF then ON.

U0-1

Error NameMain Motor stop error

ExplanationThe motor runs for over 120 seconds without any paper being fed.

U1-1

Error NameMain Motor rotation error

Explanation500ms after the IOT has started, the Main Motor Lock signal is "Low."

U2-1

Error NameCarriage Module Fail

ExplanationAn abnormality was detected in the Carriage Module.

U3-5

Error NameLaser Power or ROS Motor Fail

Explanation The ROS Motor is unable to rotate. Or, the laser output is not normal.

U4-1

Error NameFuser On Time Fail

Explanation The lamp did not turn OFF within the specified time after turning ON. Or, Warm Up was not completed within the specified time after power ON.

U4-2

Error NameOver Heat Temp Fail

ExplanationA temperature above 250C is continuously detected for 480ms.

U4-3

Error NameFS1 thermistor defect

ExplanationFS1 cannot be monitored any more.








X U7-0 CH2.1Figure 1

X U7-1 CH2.1Figure 1




Reissue

U4-9

Error NameFuser Fan defect

ExplanationAfter the start of Fan Fail Signal monitoring, the signal level was Low not more than 30 times.

U6-2

Error NameRAM read/write check error

ExplanationWhen the MCU runs the overall Read/Write check for RAM during startup, the Read Data and Write Data do not match.

U6-3

Error NameNVM data defect

Explanation The NVM Header data ERROR and NVM 3 page data do not match. Or, unable to find the NVM Write & Read area. The NVM or Counter areas are full.

U6-4

Error NameNVM read/write cannot be executed

Explanation An NVM Ack NG is detected during NVM Read. An NVM Write Error is detected 5 times during NVM Recovery.

U6-5

Error NameCPU Power to access NVM is not enough

ExplanationNVM queue full is detected during NVM Write.

U7-0

Error NameUI Communication TimeOut

ExplanationAt the Power On Sequence, the AIOC PWB did not communicate with the User Interface PWB.

U7-1

Error NameUI Communication Error

ExplanationThe User Interface PWB has detected a communication failure.

U8-1

Error NameBilling Counter Defect

Explanation It is detected that the Billing Counter Value is incorrect. Or, the AOIC PWB has failed to read the Billing Counter.

U9-0

Error NameHVPS fail

ExplanationA 500 msec cycle of the signal HVPS#ERR=High was detected twice in a row.



Display Priority in Case of Multiple Errors

Document Jamize

t

n JAM

Paper Jam

JAM JAMn JAM from STM feedAM

AM

AMAMM

Tray-related errorsismatchismatchmatchct paper tray (Tray1)ct paper tray (Tray2)

Resolvable by replac-ing parts

nd. Errort Identity Mismatchr

An error that only stops scanning

Priority Error Error CharacteristicJune, 20082-24


When multiple errors occur simultaneously, they will be shown on the Control Panel display in the following priority order. Always begin troubleshooting with the highest-priority error.

Priority Order

Error Code Error Name Error Characteristic

1 (Highest)

U7-0 UI Communication TimeOut Unable to control the display at the Control-

ler2 U7-1 UI Communication Error3 H9-7 MCU-STM comm. error

Fatal Error

4 N9-1 IOT Communication Error5 N9-0 Controller Logic fail6 U0-1 Main Motor stop error7 U1-1 Main Motor rotation error8 U2-1 Carriage Module Fail9 U3-5 Laser Power or ROS Motor Fail10 U4-1 Fuser On Time Fail11 U4-2 Over Heat Temp Fail12 U4-3 FS1 thermistor defect13 U4-9 Fuser Fan defect14 U6-2 RAM read/write check error15 U6-3 NVM data defect16 U6-4 NVM read/write cannot be executed17 U6-5 RAM read/write check error18 U8-1 Billing Counter Defect19 U9-0 HVPS fail20 E9-1 AMS NG Out Of Range

Dynamic Error(Job Cancel)

21 E9-2 Paper direction mismatch22 E8-1 Nup NG Out Of Range23 E8-2 Nup Paper direction mismatch24 L9-0 Copy Counter Full25 N4-0 No Response from USB-Host26 N4-1 HBPL or XPJL Syntax Error27 N4-2 Download File Error27 N4-3 Download Flash Write Error29 N5-0 Push Scan TimeOut30 A5-1 Platen Cover Open Document Cover

Open32 E5-1 IOT L/H Cover open

Paper Cover Open33 E5-2 IOT Front Cover open34 E6-1 L/H Low Cover open35 E6-2 STM L/H Cover open

36 A1-1 Doc Misfeed Jam37 A2-2 No Supported Doc S38 A4-1 Short Length Detec39 A4-2 Long Length Detect40 C1-1 Tray1 F/O#1 SNR o41 C1-2 Tray1 Regi SNR on42 C2-1 STM F/O#2 SNR on43 C2-2 Tray1 F/O#1 SNR o44 C2-3 STM Regi SNR on J

46 C9-3 MSI Regi SNR on J47 E1-2 Exit SNR on JAM48 E3-1 Exit SNR off JAM49 C8-1 F/O#1 SNR Static J50 C8-2 F/O#2 SNR Static J51 E1-6 Regi SNR Static JA52 E3-6 Exit SNR JAM53 E0-1 CPM Image Lost54 C0-1 APS NG Unselected

56 C5-1 Tray1 Paper Size M57 C6-1 Tray2 Paper Size M58 C7-1 MSI Paper Size Mis59 C5-0 No paper in the sele60 C6-0 No paper in the sele61 J1-2 Toner Empty62 J3-1 No Drum cartridge63 J6-1 Drum cartridge life e64 J7-1 Drum CRUM comm65 J7-2 Drum CRUM Marke66 J7-3 Drum CRUM ID erro67 N1-1 EPC Memory Full

Order Code Error Name

U0-1, U1-1Status Indicator RAPS

rror

otor Lock signal is Low.

over. Execute diagnostics [04--01 Main Motor On]. OT Motor can be heard rotating.

504 and P/J201 are connected securely.

urely.

WB P504-1 ( P/J504) (+) and GND (-). The volt-

8.1.2).

04) and J201-3 ( P/J201). The wire is not

1.1.1) and the AIOC PWB (PL 8.1) (REP 8.1.1) in

1.1 ) (REP 1.1.1). The IOT Motor is installed

.1.1) properly.

unterclockwise by hand. It rotates smoothly,

t obstruct the drive and for any incorrectly installed or incorrectly installed parts.

REP 1.1.1).

ix any installation errors.

nd J201-3 ( P/J201). The wire is not shorted

1) and the AIOC PWB (PL 8.1) (REP 8.1.1) in that June, 20082-25WorkCentre 5016, 5020

Reissue

U0-1 Main Motor Stop ErrorBSD-Reference: CH4.1 (Figure 1)

ExplanationThe motor runs for over 120 seconds without any paper being fed.

ProcedureThe problem can be solved according to RAP U1- 1 Main Motor Rotation Error (U1-1).Y N

Execute diagnostics [29-49] (How to Enter the Diagnostic Mode) to check the ROM ver-sion. The ROM is the latest version.Y N

Upgrade the ROM to the latest version.

Replace the IOT Motor (PL 1.1) (REP 1.1.1) and the AIOC PWB (PL 8.1) (REP 8.1.1) in that order.

Completed

U1-1 Main Motor Rotation EBSD-Reference: CH4.1 (Figure 1)

Explanation500 ms after the IOT Motor starts, the IOT M

ProcedureClose the Left Hand Cover and the Front C(How to Enter the Diagnostic Mode) The IY N

Check P/J504 and P/J201. Both P/JY N

Connect P/J504 and P/J201 sec

Measure the voltage between LVPS Page is approximately +24VDC.Y N

Replace the LVPS (PL 8.1) (REP

Check the wire between J504-3 ( P/J5shorted or open.Y N

Repair the wire.

Replace the IOT Motor (PL 1.1) (REPthat order.

Check the installation of the IOT Motor (PL properly.Y N

Install the IOT Motor (PL 1.1 ) (REP 1

Turn the rotor of the IOT Motor (PL 1.1 ) cowithout any abnormal load.Y N

Check for any foreign substances thaparts. There are foreign substancesY N

Replace the IOT Motor (PL 1.1) (

Remove any foreign substances and f

Check the wire between J504-3 ( P/J504) aor open.Y N

Repair the wire.

Replace the IOT Motor (PL 1.1) (REP 1.1.order.


U2-1 Carriage Module Fail U3-5 Laser Power Or ROS Motor Fail

output is not normal.

(How to Enter the Diagnostic Mode) The ROS

C PWB P403-7 ( P/J403) (+) and GND (-). The

(REP 8.1.1) and the LVPS (PL 8.1) (REP 8.1.2) in

) and the AIOC PWB (PL 8.1) (REP 8.1.1) in that

B P403-1 ( P/J403) (+) and GND (-). The volt-

8.1.1).

PWB P/J140 ( P/J140), and P/J130 ( P/J130) con- connectors are connected securely.

403), LD PWB P/J140 ( P/J140), and P/J130 ( P/

d J140 ( P/J140) and between J403 and J130 ( P/.

the AIOC PWB (PL 8.1) (REP 8.1.1) in that order.June, 20082-26U2-1, U3-5


BSD-Reference: CH6.2 (Figure 2)

ExplanationA carriage fault was detected.

ProcedureExecute diagnostics [05-22 Move scanner to home position] and [05-23 Move scanner to main-tenance position]. (How to Enter the Diagnostic Mode) The carriage moves.Y N

Check each IIT Carriage connector. Each connector is connected securely.Y N

Connect each connector securely.

Check for foreign substances and deformed parts in the carriage. None is found.Y N

Remove the foreign substances and repair the deformed parts.

Replace the IIT Carriage (PL 10.3)(REP 10.3.1).

Execute diagnostics [05-23 Move scanner to maintenance position]. When the IIT Carriage has moved to the leftmost position, press the [Stop] button to put the Carriage Sensor into the blocked state. Execute diagnostics [5-11 Home Sensor], and "H" is displayed.Y N

Check each IIT Carriage and Carriage Sensor connector. Each connector is con-nected securely.Y N


Replace the Carriage Sensor (PL 10.6) and the IIT Carriage (PL 10.3) (REP 10.3.1) in that order.

Check the Carriage Sensor (PL 10.6 ). The Carriage Sensor is installed properly.Y N

Install the Carriage Sensor (PL 10.6) properly.

Replace the IIT Carriage (PL 10.3) (REP 10.3.1).


ExplanationThe ROS Motor does not turn, or the laser

ProcedureExecute diagnostics [6-15 ROS Motor ON].Motor can be heard rotating.Y N

Measure the voltage between the AIOvoltage is approximately +24VDC.Y N

Replace the AIOC PWB (PL 8.1)that order.

Replace the ROS (PL 3.1) (REP 3.1.1order.

Measure the voltage between the AIOC PWage is approximately +5VDC.Y N

Replace the AIOC PWB (PL 8.1) (REP

Check the AIOC PWB P/J403 ( P/J403), LDnectors. The P/J403, P/J140, and P/J130Y N

Connect the AIOC PWB P/J403 ( P/JJ130) connectors securely.

Check the wires between J403 ( P/J403) anJ130) The wires are not shorted or openY N

Repair the wire(s).

Replace the ROS (PL 3.1) (REP 3.1.1) and


cted continuously for 480 ms.

t FuserOverTemp] becomes "1." Run [NVM 50-20 set it. (How to Enter the Diagnostic Mode) Check o open circuit between J601-1 ( P/J601) and of 228k ohms (cold).

).

P601 ( P/J601). The wire between J408 and

e LVPS (PL 8.1) (REP 8.1.2), and the AIOC PWB June, 20082-27WorkCentre 5016, 5020

Reissue

U4-1 Fuser On Time FailBSD-Reference: CH10.1 (Figure 1)

Explanation The lamp did not turn OFF within the specified time after turning ON. Or, Warm Up was not completed within the specified time after power ON.ProcedureWhen U4-1 occurs, [NVM 50-20 FSR Reset FuserOverTemp] becomes "3." Run [NVM 50-20 FSR Reset FuserOverTemp] using "0" to reset it. (How to Enter the Diagnostic Mode) Check to see if there is paper in the Fuser. The Fuser is normal and there is no paper in it.Y N

Remove the paper.

Check the condition of the Fuser. The Fuser is installed properly.Y N

Install the Fuser properly.

Remove the Fuser. Check the conductivity between the Thermostat contacts. The contacts are conductive. Y N

Replace the Fuser (PL 5.1) (REP 5.1.1).

Check the Heater Rod for an open circuit. There is no open circuit between J600-1 ( P/J600) and J600-2.Y N


Check the resistance of the Thermistor. There is no open circuit between J601-1 ( P/J601) and J601-2, and the resistance is a minimum of 228k ohms (cold).Y N


Immediately after Main Switch ON, the voltage between J3-3 ( P/J3) (ACH) and J3-1 (ACN) is approximately 200VAC.Y N

Replace the LVPS (PL 8.1) (REP 8.1.2).

Check the wire between J408 ( P/J408) and P601 ( P/J601). The wire between J408 and P601 is not shorted or open.Y N

Repair the wire.

Check the wire between J3 ( P/J3) and P600 ( P/J600). The wire between J3 and P600 is not shorted or open.Y N

Repair the wire.

Replace the Fuser (PL 5.1) (REP 5.1.1), the LVPS (PL 8.1) (REP 8.1.2), and the AIOC PWB (PL 8.1) (REP 8.1.1) in that order.

U4-2 Over Heat Temp FailBSD-Reference: CH10.1 (Figure 1)

ExplanationA temperature of 250C or higher was dete

ProcedureWhen U4-2 occurs, [NVM 50-20 FSR ReseFSR Reset FuserOverTemp] using "0" to rethe resistance of the Thermistor. There is nJ601-2, and the resistance is a minimumY N

Replace the Fuser (PL 5.1) (REP 5.1.1

Check the wire between J408 ( P/J408) andP601 is not shorted or open.Y N

Repair the wire.

Replace the Fuser (PL 5.1) (REP 5.1.1), th(PL 8.1) (REP 8.1.1) in that order.


U4-3 FS1 Thermistor Defect U4-9 Fuser Fan Defect

, the signal level was Low not more than 30 times.

HAD Fan (PL 9.2). The NOHAD Fan is rotating.

C PWB P405-3 ( P/J405) (+) and GND (-). The

(REP 8.1.1).

the AIOC PWB (PL 8.1) (REP 8.1.1) in that order.

B P405-2 P/J405 (+) and GND (-). The voltage

the AIOC PWB (PL 8.1) (REP 8.1.1) in that order.

1). June, 20082-28U4-3, U4-9



ExplanationThermistor FS1 cannot be monitored any more.

ProcedureCheck the condition of the Fuser. The Fuser is installed properly.Y N

Install the Fuser properly.

Check the resistance of the Thermistor. There is no open circuit between J601-1 ( P/J601) and J601-2, and the resistance is a minimum of 228k ohms (cold).Y N


Check the wire between J408 ( P/J408) and P601 ( P/J601). The wire is not shorted or open.Y N

Repair the wire.

Replace the Fuser (PL 5.1) (REP 5.1.1) and the AIOC PWB (PL 8.1) (REP 8.1.1) in that order.


ExplanationAfter the start of Fan Fail Signal monitoring

ProcedureTurn the power ON. Visually check the NOY N

Measure the voltage between the AIOvoltage is approximately +24VDC.Y N

Replace the AIOC PWB (PL 8.1)

Replace the NOHAD Fan (PL 9.2) and

Measure the voltage between the AIOC PWis 0.Y N

Replace the NOHAD Fan (PL 9.2) and

Replace the AIOC PWB (PL 8.1) (REP 8.1.


ta are mismatched. found.

onnector is connected securely.

.

1).June, 20082-29WorkCentre 5016, 5020

Reissue

U6-2 RAM Read/Write Check ErrorBSD-Reference: CH3.2 (Figure 2)

ExplanationWhen the AIOC PWB checked RAM read/write at activation, a mismatch of read and write data was detected.

ProcedureCheck each AIOC PWB connector. Each connector is connected securelyY N


Turn the power OFF and ON. U6-2 recurs.Y N

Completed


U6-3 NVM Data DefectBSD-Reference: CH3.2 (Figure 2)

Explanation NVM Header data and NVM 3 page da Or, the NVM Write & Read area is not Or, the NVM or Counter area is full.ProcedureCheck each AIOC PWB connector. Each cY N


Turn the power OFF and ON. U6-3 recursY N

Completed



U6-4 NVM Read/Write Cannot Be Executed U6-5 CPU Power To Access NVM Is Not Enough

detected.

OM version. (How to Enter the Diagnostic

.

1). June, 20082-30U6-4, U6-5



Explanation During NVM read/write, the NVM Ack NG state was detected. Or, during NVM repairs, an NVM write error was detected five times.ProcedureCheck each AIOC PWB connector. Each connector is connected securely.Y N


Turn the power OFF and ON. U6-4 recurs.Y N

Completed



ExplanationAt NVM write, the NVM queue full state was

ProcedureExecute diagnostics [29-49] to check the RMode) The ROM is the latest version.Y N

Upgrade the ROM to the latest version



ror

nication failure.

. Each connector is connected securely.

.

REP 8.4.1).June, 20082-31WorkCentre 5016, 5020

Reissue

U7-0 UI Communication TimeOutBSD-Reference: CH2.1 (Figure 1)

ExplanationAt Power ON, the AIOC PWB does not communicate with the User Interface PWB.

ProcedureMeasure each voltage between AIOC PWB J401-1 ( P/J401) (+), J401-2 (+), and GND (-). The voltages are approximately +5VDC.Y N


Check the wire between J401 ( P/J401) and J710 ( P/J710). The wire is neither shorted nor open.Y N

Repair the wire.

Replace the User Interface PWB (PL 8.4) (REP 8.4.1) and the AIOC PWB (PL 8.1) (REP 8.1.1) in that order.

U7-1 UI Communication ErBSD-Reference: CH2.1 (Figure 1)

ExplanationThe User Interface PWB detected a commu

ProcedureCheck each User Inferface PWB connectorY N


Turn the power OFF and ON. U7-1 recursY N

Completed

Replace the User Interface PWB (PL 8.4) (


U8-1 Billing Counter Defect U9-0 HVPS Fail

etected twice in a row.

over. Make sure that the Drum Cartridge and the asure the voltages between P406-2 ( P/J406) (+)/d ground (-). The voltages are approximately

8.1.1) and the HVPS (PL 8.2) (REP 8.2.1) in that

Voltage)]. (How to Enter the Diagnostic Mode) -4 (+)/P406-5 (+) become 0.

8.1.1).

he problem is solved.

( P/J406) (+) on the AIOC PWB and ground (-)..

) and J406-1 ( P/J406) on the HVPS PWB for a

VPS (PL 8.2) (REP 8.2.1).

8.1.1). June, 20082-32U8-1, U9-0



Explanation An illegal Billing Counter value was detected. Or, the AIOC PWB failed to read the Billing Counter.ProcedureTBD


ExplanationA 500 ms cycle of HVPS#ERR=High was d

ProcedureClose the Left Hand Cover and the Front CTransfer Corotron are properly seated. MeP406-4(+)/P406-5(+) on the AIOC PWB an+5VDC.Y N

Replace the AIOC PWB (PL 8.1) (REPorder.

Execute diagnostics [09-04 HVPS ON (LowThe voltages at P406-2 ( P/J406) (+)/P406Y N


Replace the HVPS (PL 8.2) (REP 8.2.1). TY N

Measure the voltage between P406-1The voltage is approximately +5VDCY N

Check between J520-1 ( P/J520short circuit.If there is no short, replace the H


Completed

062-300, 062-345Status Indicator RAPS

re

e EEPROM.

n the power. The problem is solved.

rk PWB). (REP 8.1.3) (PL 8.1)June, 20082-33WorkCentre 5016, 5020

Reissue

062-300 Platen Interlock OpenBSD-Reference: CH 5.6

ExplanationDetected the opened Platen Interlock.

ProcedureEnsure that the DADF can be closed normally. The DADF can be closed normally.Y N

Remove obstructions or repair the DADF Counter Balances. (REP 13.3.2, REP 13.3.3)

Check that the Platen Interlock is functioning properly. The Platen Interlock is functioning properly.Y N

Replace the Platen Interlock Sensor.

Replace the SLCC PWB (AIOC/Network PWB). (REP 8.1.3) (PL 8.1)

062-345 IISS EEPROM FailuBSD-Reference: CH 3.1

ExplanationError in writing on or communicatiing with th

ProcedureSwitch off the machine power then switch oY N

Replace the SLCC PWB (AIOC/Netwo

Problem is resolved.


062-360 Carriage Position Fail 062-371 Lamp Illumination Fail

Lamp to the CCD.

th between the lamp, the lens or the mirror. The

e (Reflector) is in place and not deterioarated. (PL s good.

ection Plate. (PL 10.6)

nt Control Code [62-02]. The Illumination Lamp

rly connected and repair if necessary. Replace the

B). (PL 8.1) (REP 8.1.3)June, 20082-34062-360, 062-371


BSD-Reference: CH 6.2

ExplanationDetected no input of Regi Sensor when carriage was working or detected the failure of the Regi Sensor position, or detected the failure of the IIT Regi Sensor level.

ProcedureCheck that the Lamp Carriage can move freely and has no loose cables. The Lamp Carriage and cables are good.Y N

Repair the Lamp Carriage. (REP 10.3.1)

Enter the Diagnostic Mode. Enter Component Control Code [62-212]. Check the operation of the IIT Regi Sensor. The Regi Sensor is good.Y N

Reseat the Regi Sensor connector. Check the wiring for proper operation and repair if necessary. Replace the Regi Sensor. (PL 10.6)

Enter the Diagnostic Mode. Enter Component Control Code [05-22]. The Carriage moves in the scan direction.Y N

Check the connector of the Carriage Motor and repair if necessary. Replace the Carriage Motor. (PL 10.6)

Replace the SLCC PWB (AIOC/Network PWB). (PL 8.1) (REP 8.1.3)


ExplanationDetected incufficient light provided from the

ProcedureCheck for any obstructions in the optical paoptical path is clear of any obstructions.Y N

Remove the obstuctions.

Check that the White Color Correction Plat10.6) The White Color Correction Tape iY N

Clean or replace the White Color Corr

Enter the Diagnostic Mode. Enter Componeis good.Y N

Check that the Lamp harness is propeIllumination Lamp. (REP 10.6.1)

Replace the SLCC PWB (AIOC/Network PW

062-380, 062-386Status Indicator RAPS

t of the CCD at AOC (Automatic Offset Control) of

nection. The problem has been resolved.

OMS (AIOC/Network PWB). (PL 8.1) (REP 8.1.3) June, 20082-35WorkCentre 5016, 5020

Reissue

062-380 AGC FailureBSD-Reference: CH 6.2

ExplanationControl logic has detected insufficient light from the Illumination Lamp during AGC (Automatic Gain Congrol) of the auto IIT Calibration at Start.

ProcedureCheck for any obstructions in the optical path. Clean the Mirror, lens and the white balance strip. Switch off the power then switch it on again. The problem has been resolved.Y N

Enter the Diagnostic Mode. Enter Component Control Code [62-02]. The lamp is good.Y N

Check that the Lamp harness is properly connected and repair if necessary. Replace the Illumination Lamp. (REP 10.6.1)

Replace the SLCC PWB and (3) EEPROMS (AIOC/Network PWB). (PL 8.1) (REP 8.1.3)

POPO the machine and retry.

062-386 AOC FailureBSD-Reference: CH 6.1

ExplanationControl logic has detected an output defecthe auto IIT Calibration at Start.

ProcedureCheck the connector P/J410 for proper conY N

Replace the SLCC PWB and (3) EEPR

POPO the machine and retry.


062-392 IPS PWB Memory Fail 062-393 IPS PWB Fail

writing error to the SLCC EEPROMs.

in. If the problem is not solved, replace the SLCC . (REP 8.1.3) June, 20082-36062-392, 062-393



ExplanationControl logic has detected RAM malfunction of IISS PWB.

ProcedureSwitch off the power then switch it on again. If the problem is not solved, replace the SLCC PWB (AIOC/Network) and the 3 EEPROMs. (REP 8.1.3)


ExplanationControl logic has detected a test error or a

ProcedureSwitch off the power then switch it on agaPWB (AIOC/Network) and the 3 EEPROMs

005-170Status Indicator RAPS

tch (PL 13.9)

Roller. (REP 13.9.1)

.9).

A B CJune, 20082-37WorkCentre 5016, 5020

Reissue

005-170 DADF Feed FailureBSD-Reference: CH 5.2

ExplanationThe control logic has detected the failure of paper to reach the Document Feed Sensor after the Feed Clutch has energized.

ProcedureCheck for obstructions in the Document Tray. Clean the Feed Roll. Confirm that a document is feeding into the document handler. The Feed Roller feeds paper into the document han-dler.Y N

The Document Drive Motor operates.Y N

Enter the Diagnostic Mode. Enter Component Control Code [05-01]. The Docu-ment Drive Motor operates.Y N

There is +24 VDC at connector CN2 pin 1 and pin 4 on the DADF PWB.Y N

Check the following in order:1. Check the connectors CN1 and CN2 on the DADF PWB for proper

connections2. Check the connector J414 on the SLCC PWB (AIOC) for proper con-

nection.3. Check the harness from the DADF PWB to the SLCC PWB for an

open circuit.If the harness and the connectors are good, replace the DADF PWB (REP 13.2.4)

Replace the Document Drive Motor (PL 13.5)

The Feed Roller rotates.Y N

Enter the Diagnostic Mode. Enter Component Control Code [05-62]. The Doc-ument Feed Clutch operates.Y N

Check the connector of the Document Feed Clutch (PL 13.9) If the con-nector is good, replace the Document Feed Clutch (PL 13.9).

Replace the Document Feed Clutch (PL 13.9)

Replace the Pick Up Roller and Feed Roller. (REP 13.9.1)

The Feed Roller rotates.Y N

Enter the Diagnostic Mode. Enter Component Control Code [05-62]. The Docu-ment Feed Clutch operates.Y N

Check the connector of the Document Feed Clutch (PL 13.9) If the connector is good, replace the Document Feed Clutch (PL 13.9).

Replace the Document Feed Clu

Replace the Pick Up Roller and Feed

Replace the Document Feed Sensor (PL 13

A B C

WorkCentre 5016, 502

Documents

Xerox-WC-5016-5020-Service manua.pdf