X X X X X X X X X X ONLY READ - IAPMO Group California Mechanical Code/Chapter 17.pdf · 2013 CALIFORNIA MECHANICAL CODE 301 ... 6th Edition Balancing 317.1 ... Rules for Construction

3012013 CALIFORNIA MECHANICAL CODE

CALIFORNIA MECHANICAL CODE – MATRIX ADOPTION TABLECHAPTER 17 – REFERENCED STANDARDS

(Matrix Adoption Tables are non-regulatory, intended only as an aid to the user. See Chapter 1 for state agency authority and building application.)

Adopting Agency BSC SFMHCD DSA OSHPD

BSCC DPH AGR DWR CA SL SLC1 2 1-AC AC SS SS/CC 1 2 3 4

Adopt Entire Chapter

Adopt Entire Chapter as amended(amended sections listed below) X X X X X X X X X X

Adopt only those sections that arelisted below

Chapter/SectionTable 1701.0Standards for Equipment andMaterials

X X X X X X X X X X

READ ONLY

302 2013 CALIFORNIA MECHANICAL CODE

READ ONLY


1701.0 General.1701.1 Applicability. This chapter covers standards that arehereby declared to be part of this code. This chapter lists stan-dards that relate to equipment and materials specified in thiscode, but are not adopted as part of this code.1701.2 Standards. The standards listed in Table 1701.0 areintended for use as a guide in the design, testing, and installationof equipment regulated by this code. These standards are manda-tory where required by sections in this code.

Organization abbreviations referred to in Table 1701.0 aredefined in a list found at the end of the table.

CHAPTER 17REFERENCED STANDARDS

READ ONLY

REFERENCED STANDARDS


TABLE 1701.0REFERENCED STANDARDS

STANDARD NUMBER STANDARD TITLE APPLICATION REFERENCED SECTION

AABC-2002 Total System Balance, 6th Edition Balancing 317.1ACCA Manual B-2009 Balancing and Testing Air and Hydronic Systems Balancing 317.1ACCA Manual D-2009* Residential Duct Systems Ducts, Balancing E 502.4.4ACCA Manual J-2006* Residential Load Calculation Ducts Table E 502.6ACCA Manual N-2008 Commercial Load Calculation Ducts 103.1, 306.1ACCA Manual Q-2003 Low Pressure, Low Velocity Duct System Design Ducts 103.1, 306.1ACCA 4 QM-2007* Maintenance of Residential HVAC Systems Maintenance 102.4.2AHRI 700-2006 Specification for Fluorocarbon Refrigerants Refrigerants 1105.4.1AMCA 500-D-2007* Laboratory Methods of Testing Dampers for Ratings Dampers E 503.4.3.4(C)AMCA 540-2008* Louvers Impacted by Wind Borne Debris Testing 318.1.2AMCA 550-2009* High Velocity Wind Driven Rain Resistance Louvers Testing 318.1.1ASCE 25-2006* Earthquake-Actuated Automatic Gas Shutoff Devices Fuel Gas 103.1, 306.1ASHRAE 15-2010* Safety Standard for Refrigeration Systems Refrigeration Systems 1102.1ASHRAE 34-2010* Designation and Safety Classification of Refrigerants Refrigeration Classifi-

cations Table 1102.2

ASHRAE 52.1-1992 Gravimetric and Dust Spot Procedures for Testing AirCleaning Devices Used in General Ventilation for RemovingParticulate Matter

Testing E 603.1.1(4)

ASHRAE 52.2-2007 General Ventilation Air Cleaning Devices for Removal Effi-ciency by Particle Size

Cleaning Devices E 201.8, E 603.1.1(4)

ASHRAE 55-2010 Thermal Environmental Conditions for Human Occupancy Miscellaneous E 607.1ASHRAE 62.1-2010* Ventilation for Acceptable Indoor Air Quality Indoor Air Quality

Ventilation 402.4.1, E 503.4.3.10(1)(b),E 503.4.3.10(2)(b), E 503.5(2), E 503.5.5(1)(b),E 503.5.5(2)(a)(2), E 503.5.5.2(1), E 606.1

ASHRAE 62.2-2010* Ventilation and Acceptable Indoor Air Quality in Low-RiseResidential Buildings

Ventilation, Dwelling 402.1.2, E 605.1.4, E 605.1.7.1,E 605.1.7.2

ASHRAE 90.1-2010* Energy Standard for Buildings Except Low-Rise ResidentialBuildings

Energy E 503.2, E 503.3.2, E 503.4.1.3,E 503.4.4.1, E 503.4.4.2, E 503.6.5.2, Table E 503.7.1(1-5),Table E 503.7.1(7-10)

ASHRAE 90.2-2007* Energy-Efficient Design of Low-Rise Residential Buildings Energy, Dwellings 103.1, 306.1ASHRAE 111-2008* Measurement, Testing, Adjusting and Balancing of Building

HVAC SystemsBalancing 317.1(3)

ASHRAE 129-1997(R2002)*

Measuring Air-Change Effectiveness Used As An AlternateSizing Value

Table 403.2.2

ASHRAE 136-1993(R2006)*

A Method of Determining Air Change Rates in DetachedDwellings

Ventilation E 605.1.3.3

ASHRAE/ACCA 180-2008*

Inspection and Maintenance of Commercial-Building HVACSystems

Maintenance 102.4.1, 1023.1

ASHRAE/ACCA 183-2007*

Peak Cooling and Heating Load Calculations in BuildingsExcept Low-Rise Residential Buildings

Cooling and HeatingLoad, Miscellaneous

E 503.4.2

ASHRAE Handbook-2009 Fundamentals Climatic Conditions E 503.4.2, F 2.4ASHRAE -Handbook-2008 HVAC Systems and Equipment Design 103.1, 306.1

READ ONLY




ASME A13.1-2007* Scheme for the Identification of Piping Systems Piping 103.1, 306.1

ASME A112.4.1-2009* Water Heater Relief Valve Drain Tubes Piping 103.1, 306.1ASME A112.18.6-2009/CSA B125.6-2009*

Flexible Water Connectors Piping, Water Supply 103.1, 306.1

ASME B1.20.1-1983(R2006)*

Pipe Threads, General Purpose, Inch Joints 1308.5.9

ASME B1.20.3-1976(R2008)*

Dryseal Pipe Threads, Inch Joints 103.1, 306.1

ASME B16.1-2010* Gray Iron Pipe Flanges and Flanged Fittings: Classes 25,125, and 250

Fittings 1308.5.12

ASME B16.3-2006* Malleable Iron Threaded Fittings: Classes 150 and 300 Fittings Table 1201.3.1ASME B16.5-2009* Pipe Flanges and Flanged Fittings: NPS 1⁄2 through 24

Metric/InchFittings Table 1201.3.1

ASME B16.9-2007* Factory-Made Wrought Buttwelding Fittings Fittings Table 1201.3.1ASME B16.11-2009 Forged Fittings, Socket-Welding and Threaded Fittings Table 1201.3.1ASME B16.15-2006* Cast Copper Alloy Threaded Fittings: Classes 125 and 250 Fittings Table 1201.3.1ASME B16.18-2001(R2005)*

Cast Copper Alloy Solder Joint Pressure Fittings (Note 1) Fittings Table 1201.3.1

ASME B16.20-2007* Metallic Gaskets for Pipe Flanges: Ring-Joint, Spiral-Wound,and Jacketed

Joints 1308.5.12

ASME B16.22-2001(R2010)*

Wrought Copper and Copper Alloy Solder Joint PressureFittings

Fittings Table 1201.3.1

ASME B16.23-2002(R2006)*

Cast Copper Alloy Solder Joint Drainage Fittings: DWV Fittings Table 1201.3.1

ASME B16.24-2006* Cast Copper Alloy Pipe Flanges and Flanged Fittings:Classes 150, 300, 600, 900, 1500, and 2500


ASME B16.26-2006* Cast Copper Alloy Fittings for Flared Copper Tubes Fittings Table 1201.3.1ASME B16.29-2007* Wrought Copper and Wrought Copper Alloy Solder-Joint

Drainage Fittings-DWV (Note 1)Fittings Table 1201.3.1

ASME B16.33-2002(R2007)*

Manually Operated Metallic Gas Valves for use in Gas PipingSystems up to 125 psi (Sizes NPS 1⁄2 -NPS 2)

Valves 103.1, 306.1

ASME B16.50-2001(R2008)*

Wrought Copper and Copper Alloy Braze-Joint PressureFittings

Fittings 103.1, 306.1

ASME B31.5-2010* Refrigeration Piping and Heat Transfer Components Refrigeration Piping,Piping

103.1, 306.1

ASME B36.10M-2004(R2010)*

Welded and Seamless Wrought Steel Pipe Piping, Ferrous 1308.5.2.2(1)

ASME BPVC Section I-2010*

Rules for Construction of Power Boilers Boilers Table 1011.1

ASME BPVC Section IV-2010*

Rules for Construction of Heating Boilers Miscellaneous 1002.1(2)

ASME BPVC SectionVIII-2010*

Rules for Construction of Pressure Vessels Division 1 Miscellaneous 1334.6.2

ASME CSD-1-2009 Controls and Safety Devices for Automatically Fired Boilers Boilers, Controls 1002.1 ASTM A 53/A 53 M-2010 Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded, and

Seamless Piping, Ferrous 1308.5.2.2(2),

Table 1201.3.1ASTM A 106/A 106M-2010

Seamless Carbon Steel Pipe for High-Temperature Service Piping, Ferrous 1308.5.2.2(3), Table 1201.3.1

ASTM A 126-2004(R2009)

Gray Iron Castings for Valves, Flanges, and Pipe Fittings Piping, Ferrous Table 1201.3.1

ASTM A 254-1997(R2007)

Copper-Brazed Steel Tubing Piping, Ferrous 1308.5.3.1, 1330.1,Table 1201.3.1

ASTM A 312-2009 Seamless, Welded, and Heavily Cold Worked AusteniticStainless Steel Pipes

Piping, Ferrous 103.1, 306.1

READ ONLY




ASTM A 420-2010a Piping Fittings of Wrought Carbon Steel and Alloy Steel forLow-Temperature Service


ASTM A 568-2009a Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled

Piping Table D 3.0

ASTM A 653/A 653M-2010

Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process

Piping, Ferrous Table D 3.0

ASTM A 733-2003(R2009)e1

Welded and Seamless Carbon Steel and Austenitic StainlessSteel Pipe Nipples

Piping, Ferrous 103.1, 306.1

ASTM A 861-2004(R2008)

High-Silicon Iron Pipe and Fittings (Note 1) Piping, Ferrous 103.1, 306.1

ASTM B 32-2008 Solder Metal (Note 2) Joints 103.1, 306.1ASTM B 42-2010 Seamless Copper Pipe, Standard Sizes Piping, Copper Alloy Table 1201.3.1ASTM B 43-2009 Seamless Red Brass Pipe, Standard Sizes Piping, Copper Alloy Table 1201.3.1ASTM B 75-2002 (R2010) Seamless Copper Tube Piping, Copper Alloy Table 1201.3.1

ASTM B 88-2009 Seamless Copper Water Tube Piping, Copper Alloy 1308.5.3.2, 1330.1,Table 1201.3.1

ASTM B 135-2010 Seamless Brass Tube Piping, Copper Alloy Table 1201.3.1

ASTM B 210-2004 Aluminum and Aluminum-Alloy Drawn Seamless Tubes Piping, Ferrous 1308.5.3.3 ASTM B 241/A 241M-2010

Aluminum and Aluminum-Alloy Seamless Pipe and Seam-less Extruded Tube

Piping, Ferrous 1308.5.2.4, 1308.5.3.3

ASTM B 251-2010 General Requirements for Wrought Seamless Copper andCopper-Alloy Tube

Piping, Copper Alloy Table 1201.3.1

ASTM B 280-2008 Seamless Copper Tube for Air Conditioning and Refrigera-tion Field Service

Piping, Copper Alloy 1308.5.3.2, 1330.1

ASTM B 302-2007 Threadless Copper Pipe, Standard Sizes Piping, Copper Alloy Table 1201.3.1ASTM B 306-2009 Copper Drainage Tube (DWV) Piping, Copper Alloy 103.1, 306.1ASTM B 370-2009 Copper Sheet and Strip for Building Construction Miscellaneous 103.1, 306.1ASTM B 447-2007 Welded Copper Tube Piping, Copper Alloy Table 1201.3.1

ASTM B 587-2008 Welded Brass Tube Piping, Copper Alloy 103.1, 306.1ASTM B 687-1999(R2005)e1

Brass, Copper, and Chromium-Plated Pipe Nipples Piping, Copper Alloy 103.1, 306.1

ASTM B 813-2010 Liquid and Paste Fluxes for Soldering of Copper and CopperAlloy Tube

Joints 103.1, 306.1

ASTM B 828-2002(R2010)

Making Capillary Joints by Soldering of Copper and CopperAlloy Tube and Fittings

Joints 103.1, 306.1

ASTM C 296-2000(R2009)e1

Asbestos-Cement Pressure Pipe Piping, Non-Metallic Table 1201.3.1

ASTM C 315-2007 Clay Flue Liners and Chimney Pots Appliances 803.1.12.1

ASTM C 411-2005 Hot-Surface Performance of High-Temperature ThermalInsulation

Block Board,Cracking, Delamina-tion, Hot-SurfacePerformance, PipeThermal Insulation,Surface Analysis-Building, TemperatureTests-Insulation,Thermal InsulatingMaterials

604.1, 1201.3.2.11,1201.4.1.2

READ ONLY




ASTM C 518-2010 Steady-State Thermal Transmission Properties by Means ofthe Heat Flow Meter Apparatus

Certification: Calibra-tion, Error Analysis,Heat Flow MeterApparatus, Heat Flux,Instrument Verifica-tion, Thermal Conduc-tivity, ThermalResistance, ThermalTesting, Tunnel Test

Table E 503.7.1(9),Table E 503.7.1(10)

ASTM D 93-2010a Flash Point by Pensky-Martens Closed Cup Tester Certification 103.1, 306.1ASTM D 396-2010 Fuel Oils Boiler C 2.0ASTM D 1527-1999(R2005)*

Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe, Sched-ules 40 and 80

Piping, Plastic Table 1201.3.1

ASTM D 1693-2008 Environmental Stress-Cracking of Ethylene Plastics Piping, Plastic Table 1201.3.1ASTM D 1785-2006* Poly (Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80,

and 120Piping, Plastic Table 1201.3.1

ASTM D 2241-2009* Poly (Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDRSeries)


ASTM D 2464-2006* Threaded Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings,Schedule 80 (Note 1)


ASTM D 2466-2006* Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule40 (Note 1)


ASTM D 2467-2006* Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule80 (Note 1)


ASTM D 2513-2011* Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings(Note 1)

Piping, Plastic 1308.5.4, 1308.5.6.2,1308.5.11.2,1311.1.7.1(1), 1330.3,Table 1201.3.1

ASTM D 2517-2006* Reinforced Epoxy Resin Gas Pressure Pipe and Fittings Piping, Plastic 1330.3ASTM D 2609-2002(R2008)*

Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe(Note 1)


ASTM D 2683-2010* Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing

Fittings E 505.1.2, Table 1201.3.1

ASTM D 2837-2008 Obtaining Hydrostatic Design Basis for Thermoplastic PipeMaterials or Pressure Design Basis for Thermoplastic PipeProducts


ASTM D 2846-2009b* Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Hot-andCold-Water Distribution Systems


ASTM D 3035-2010* Polyethylene (PE) Plastic Pipe (DR-PR) Based on ControlledOutside Diameter

Piping, Plastic E 505.1.2, Table 1201.3.1

ASTM D 3261-2010a* Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Poly-ethylene (PE) Plastic Pipe and Tubing


ASTM D 3350-2010a Polyethylene Plastics Pipe and Fittings Materials Piping, Fittings E 505.1.2, Table 1201.3.1

ASTM E 84-2010b* Surface Burning Characteristics of Building Materials Miscellaneous 602.2, 604.1,1201.3.2.11,1201.4.1.2, Table 303.4

ASTM E 96-2005 Water Vapor Transmission of Materials Miscellaneous E 502.4.1ASTM E 136-2011 Behavior of Materials in a Vertical Tube Furnace at 750°C Furnace 216.0ASTM E 814-2011* Fire Tests of Penetration Firestop Systems Miscellaneous 507.2.4, 507.2.5ASTM E 2231-2009 Specimen Preparation and Mounting of Pipe and Duct Insula-

tion Materials to Assess Surface Burning Characteristics Certification: IEEE,Insulation, Pipe,Preparation

604.1, 1201.3.2.11,1201.4.1.2

READ ONLY




ASTM E 2336-2004(R2009)

Fire Resistive Grease Duct Enclosure Systems Field FabricatedGrease Duct

507.2.5

ASTM F 437-2009* Threaded Chlorinated Poly (Vinyl Chloride) (CPVC) PlasticPipe Fittings, Schedule 80


ASTM F 438-2009* Socket-Type Chlorinated Poly (Vinyl Chloride) (CPVC)Plastic Pipe Fittings, Schedule 40


ASTM F 439-2009* Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic PipeFittings, Schedule 80


ASTM F 441-2009* Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe,Schedules 40 and 80


ASTM F 442-2009* Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe(SDR-PR)


ASTM F 876-2010* Crosslinked Polyethylene (PEX) Tubing Piping, Plastic Table 1201.3.1ASTM F 877-2007* Crosslinked Polyethylene (PEX) Plastic Hot- and Cold-Water

Distribution Systems Piping, Plastic 1201.4.2,

Table 1201.3.1ASTM F 1055-1998(R2006)*

Electrofusion Type Polyethylene Fittings for Outside Diam-eter Controlled Polyethylene Pipe and Tubing


ASTM F 1281-2007* Crosslinked Polyethyene/Aluminum/Crosslinked Polyeth-ylene (PEX-AL-PEX) Pressure Pipe

Piping, Plastic 1201.5.2, Table 1201.3.1

ASTM F 1282-2010* Polyethylene/Aluminum/Polyethylene (PE-AL-PE)Composite Pressure Pipe

Piping, Plastic 1201.8.1.4, Table 1201.3.1

ASTM F 1476-2007* Performance of Gasketed Mechanical Couplings for Use inPiping Applications

Joints 103.1, 306.1

ASTM F 1807-2010e1* Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyeth-ylene of Raised Temperature (PE-RT) Tubing


ASTM F 1960-2010* Cold Expansion Fittings with PEX Reinforcing Rings for Usewith Cross-linked Polyethylene (PEX) Tubing


ASTM F 1961-2009* Metal Mechanical Cold Flare Compression Fittings with DiscSpring for Crosslinked Polyethylene (PEX) Tubing


ASTM F 1970-2005* Special Engineered Fittings, Appurtenances or Valves for Usein Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (VinylChloride) (CPVC) Systems


ASTM F 1973-2008* Factory Assembled Anodeless Risers and Transition Fittings inPolyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12(PA12) Fuel Gas Distribution Systems

Fuel Gas 1311.1.7.1(2)

ASTM F 1974-2009* Metal Insert Fittings for Polyethylene/Aluminum/Polyeth-ylene and Crosslinked Polyethylene/Aluminum/ CrosslinkedPolyethylene Composite Pressure Pipe

Fittings 1201.8.1.4, Table 1201.3.1

ASTM F 2080-2009* Cold-Expansion Fittings with Metal Compression-Sleeves forCrosslinked Polyethylene (PEX) Pipe


ASTM F 2098-2008* Stainless Steel Clamps for Securing SDR9 Cross-linkedPolyethylene (PEX) Tubing to Metal Insert and Plastic InsertFittings

Joints 103.1, 306.1

ASTM F 2158-2008 Residential Central-Vacuum Tube and Fittings Central Vacuum,Fittings, PVC, Tube

103.1, 306.1

ASTM F 2159-2010* Plastic Insert Fittings Utilizing a Copper Crimp Ring forSDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9Polyethylene of Raised Temperature (PE-RT) Tubing


ASTM F 2262-2009* Crosslinked Polyethylene/Aluminum/Crosslinked Polyeth-ylene Tubing OD Controlled SDR9

Piping, Plastic 103.1, 306.1

READ ONLY




ASTM F 2389-2010 Pressure-Rated Polypropylene (PP) Piping Systems Piping, Plastic 1201.6.1.1,1201.6.1.3, Table 1201.3.1

ASTM F 2434-2009* Metal Insert Fittings Utilizing a Copper Crimp Ring forSDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9Cross-linked Polyethylene/Aluminum/Cross-linked Polyeth-ylene (PEX-AL-PEX) Tubing


ASTM F 2509-2006* Field-Assembled Anodeless Riser Kits for Use on OutsideDiameter Controlled Polyethylene Gas Distribution Pipe andTubing

Fuel Gas 1311.1.7.1(3)

ASTM F 2623-2008 Polyethylene of Raised Temperature (PE-RT) SDR9 Tubing Piping, Plastic Table 1201.3.1ASTM F 2735-2009 Plastic Insert Fittings for SDR9 Cross-linked Polyethylene

(PEX) and Polyethylene of Raised Temperature (PE-RT)Tubing


ASTM F 2769-2009 Polyethylene of Raised Temperature (PE-RT) Plastic Hot andCold-Water Tubing and Distribution Systems

Piping and Fittings 1201.7, Table 1201.3.1, Table 1201.7(2)

AWS A5.8-2004* Filler Metals for Brazing and Braze Welding Joints 103.1, 306.1AWS B2.4-2006* Welding Procedure and Performance Qualification for Ther-

moplastics Joints, Certification 1308.5.11.2

AWWA C110-2008* Ductile-Iron and Gray-Iron Fittings Fittings Table 1201.3.1AWWA C115-2005 Flanged Ductile-Iron Pipe with Ductile-Iron or Gray-Iron

Threaded FlangesPiping Table 1201.3.1

AWWA C151-2009* Ductile-Iron Pipe, Centrifugally Cast Piping, Ferrous Table 1201.3.1AWWA C153-2006* Ductile-Iron Compact Fittings for Water Service Fittings Table 1201.3.1AWWA C203-2008* Coal-Tar Protective Coatings and Linings for Steel Water

Pipelines -Enamel and Tape– Hot-Applied Miscellaneous 103.1, 306.1

AWWA C500-2009* Metal-Seated Gate Valves for Water Supply Service Valves 103.1, 306.1CAN/CGSB 3.2-2007 Heating Fuel Oil Fuel Oil 103.1, 306.1CGA 2.91a-M 1997(R2002)*

Gas-Fired, Heat Activated Air Conditioning and Heat PumpAppliances (same as CSA Z21.40.1a-1997) (R2002)

Gas Fired Air Condi-tioning, Gas FiredHeat Pump

103.1, 306.1

CGA 6.14-M96 (R2001)* Automatic Vent Damper Devices for Use with Gas-FiredAppliances (same as CSA Z21.66-1996 (R2001))

Vent Dampers, Auto-matic Dampers

103.1, 306.1

CSAAmerica FC 1-2004(R2009)*

Stationary Fuel Cell Power Systems Fuel Cell PowerPlants

103.1, 306.1

CSAB137.1-2009 Polyethylene (PE) Pipe, Tubing, and Fittings for Cold-WaterPressure Services

Piping, Plastic E 505.1.2, Table 1201.3.1

CSAB137.5-2009 Crosslinked Polyethylene (PEX) Tubing Systems for PressureApplications


CSAB137.9-2009 Polyethylene/Aluminum/Polyethylene (PE-AL-PE)Composite Pressure-Pipe Systems


CSAB137.10-2009 Crosslinked Polyethylene/Aluminum/Crosslinked Polyeth-ylene (PEX-AL-PEX) Composite Pressure-Pipe Systems


CSAC448-2002 Design and Installation of Earth-Energy Systems Miscellaneous E 505.1.1CSA F379 Series-2009 Packaged Solar Domestic Hot Water Systems (Liquid to

Liquid Heat Transfer)Solar Heating Systems USEC

CSA LC1a-2009* Fuel Gas Piping Systems Using Corrugated Stainless SteelTubing (CSST) (same as CSA 6.26a)

Fuel Gas 1308.5.3.4

CSA LC4-2007* Press-Connect Copper and Copper Alloy Fittings For Use inFuel Gas Distribution Systems (same as CSA6.32)

Fuel Gas 1308.5.10.2

READ ONLY




CSA Z21.1-2010* Household Gas Cooking Appliances Household CookingAppliances, Gas Fired

103.1, 306.1

CSA Z21.5.1a-2007* Gas Clothes Dryers-Volume I, Type 1 Clothes Dryers (sameas CSA 7.1a)

Fuel Gas, Appliances 103.1, 306.1

CSA Z21.5.2a-2006(R2010)*

Gas Clothes Dryers-Volume II, Type 2 Clothes Dryers (sameas CSA 7.2a)


CSA Z21.8-1994 (R2002)* Installation of Domestic Gas Conversion Burners Cooking Appliances,Gas Burners

906.1

CSA Z21.10.1a-2009* Gas Water Heaters-Volume I, Storage Water Heaters withInput Ratings of 75 000 Btu Per Hour or Less (same as CSA4.1a)


CSA Z21.10.3b-2008(R2010)*

Gas Water Heaters-Volume III, Storage Water Heaters withInput Ratings Above 75 000 Btu Per Hour, Circulating andInstantaneous (same as CSA 4.3b)


CSA Z21.11.2-2010* Gas-Fired Room Heaters, Volume II, Unvented RoomHeaters

Room Heaters,Unvented Heaters

103.1, 306.1

CSA Z21.12b-1994(R2010)*

Draft Hoods Fuel Gas, Appliances 103.1, 306.1

CSA Z21.13b-2010* Gas-Fired Low Pressure Steam and Hot Water Boilers (sameas CSA 4.9b)


CSA Z21.15-2009* Manually Operated Gas Valves for Appliances, ApplianceConnector Valves and Hose End Valves (same as CSA 9.1)

Fuel Gas 103.1, 306.1

CSA Z21.17a-2008* Domestic Gas Conversion Burners (same as CSA 2.7a) Conversion BurnerInstallation, GasBurners

103.1, 306.1

CSA Z21.18a-2010* Gas Appliance Pressure Regulators (same as CSA 6.3) Appliance Regulators,Gas Refrigerators,Pressure Regulators

103.1, 306.1

CSA Z21.19a-2009* Refrigerators Using Gas Fuel (same as CSA 1.4a) Gas Refrigerators,Refrigerators

103.1, 306.1

CSA Z21.20a-2008* Automatic Gas Ignition Systems and Components Automatic Ignition,Gas Ignition, Ignition

103.1, 306.1

CSA Z21.21a-2010* Automatic Valves for Gas Appliances (same as CSA 6.5a) Appliance Valves,Automatic GasValves, Valves

103.1, 306.1

CSA Z21.22b-2001(R2008)*

Relief Valves for Hot Water Supply Systems (same as CSA4.4b)

Valves 103.1, 306.1

CSA Z21.23-2010* Gas Appliance Thermostats Thermostats 103.1, 306.1CSA Z21.24a-2009* Connectors for Gas Appliances (same as CSA 6.10a) Fuel Gas 919.2, 1312.1(3)CSA Z21.35a-2010* Pilot Gas Filters (same as CSA 6.8a) Filters, Pilot Filters 103.1, 306.1

CSA Z21.41b-2010* Quick Disconnect Devices for Use with Gas Fuel Appliances(same as CSA 6.9b)

Fuel Gas 103.1, 306.1

CSA Z21.42a-2004(R2007)*

Gas-Fired Illuminating Appliances Illuminating Appli-ances

103.1, 306.1

CSA Z21.47b-2008* Gas-Fired Central Furnaces (same as CSA 2.3b) Fuel Gas, Appliances Table E 503.7.1(5)CSA Z21.50b-2009* Vented Gas Fireplaces (same as CSA 2.22b) Appliances, Decora-

tive Appliances 103.1, 306.1

CSA Z21.54b-2009* Gas Hose Connectors for Portable Outdoor Gas-Fired Appli-ances (same as CSA 8.4b)

Fuel Gas 1312.2.2

CSA Z21.56a-2008* Gas-Fired Pool Heaters (same as CSA 4.7a) Fuel Gas, SwimmingPools, Spas, and HotTubs

103.1, 306.1

CSA Z21.58a-2008* Outdoor Cooking Gas Appliances (same as CSA 1.6a) Cooking Appliances 103.1, 306.1

READ ONLY




CSA Z21.60b-2006(R2007)*

Decorative Gas Appliances for Installation in Solid-FuelBurning Fireplaces (same as CSA 2.26b)

Decorative Appli-ances, DecorativeFireplace Appliances

103.1, 306.1

CSA Z21.61-1983(R2004)*

Gas-Fired Toilets Toilets 103.1, 306.1

CSA Z21.69-2009* Connectors for Moveable Gas Appliances (same as CSA6.16)

Fuel Gas 1312.1(6), 1312.1.1

CSA Z21.71a-2005(R2007)*

Automatic Intermittent Ignition Systems for Field Installation Automatic Pilot Igni-tion, Pilot Ignition

103.1, 306.1

CSA Z21.80b-2010* Line Pressure Regulators (same as CSA 6.22b) Fuel Gas 1308.7.2,1308.7.5.1(1)

CSA Z21.86-2008* Vented Gas-Fired Space Heating Appliances (same as CSA2.32)

Fuel Gas Appliances 103.1, 306.1

CSA Z21.88-2009* Vented Gas Fireplace Heaters (same as CSA 2.33) Fireplace Heaters 103.1, 306.1CSA Z21.90b-2006* Gas Convenience Outlets and Optional Enclosures (same as

CSA 6.24b) Gas Outlets 1312.6

CSA Z83.4b-2006 (R2009) Non-Recirculating Direct Gas-Fired Industrial Air Heaters(same as CSA 3.7b)

Air Heaters, Non-Recirculating, Non-Recirculating Heaters

909.1

CSA Z83.7b-2009* Gas-Fired Construction Heaters (same as CSA 2.14b) Fuel Gas Appliances 103.1, 306.1CSA Z83.8a-2009* Gas Unit Heaters and Gas-Fired Duct Furnaces (same as CSA

2.6a)Fuel Gas Appliances Table E 503.7.1(5)

CSA Z83.11b-2009* Gas Food Service Equipment (same as CSA 1.8b) Fuel Gas, Appliances 103.1, 306.1CSA Z83.18b-2008* Recirculating Direct Gas-Fired Industrial Air Heaters Air Heaters, Industrial

Heaters, Recirculating 910.1

CSA Z83.19-2009* Gas-Fired High-Intensity Infrared Heaters (same as CSA2.35)

High IntensityHeaters, InfraredHeaters

103.1, 306.1

CSA Z83.20a-2010* Gas-Fired Low-Intensity Infrared Heaters (same as CSA2.34a)

Infrared Heaters, LowIntensity Heaters

103.1, 306.1

EPA 202-1996 (R2010) Determination of Condensable Particulate Emissions forStationary Sources

Miscellaneous 508.1(1), 516.2.9(2)

IAPMO IS 13-2006 Protectively Coated Pipe Pipe Coatings 103.1, 306.1IAPMO PS 33-2010c Flexible PVC Hose for Pools, Hot Tubs, Spas and Jetted

Bathtub Swimming Pools,Spas, and Hot Tubs

USPSHTC

IAPMO PS 117-2008 Copper and Copper Alloy Tubing System IncorporatingPress-Type or Nail-Type Connections

Fittings 103.1, 306.1

IAPMO PS 120-2004 Flashing and Stand Combination for Air Conditioning Units(Residential or Commercial Unit Curb)

Air ConditioningFlashing Stand

103.1, 306.1

IAS 1-91-1992 U.S. Requirements for Indirect Water Heaters for Use WithExternal Heat Source

Indirect Water Heaters 103.1, 306.1

IIAR 2-2008* Equipment, Design, and Installation of Closed-CircuitAmmonia Mechanical Refrigerating Systems

Ammonia Refrigera-tion Systems

1102.1

ISO/IEC Guide 65-1996 General Requirements for Bodies Operating Product Certifi-cation Systems

Certification 103.1, 306.1

MSS SP-6-2007 Finishes for Contact Faces of Pipe Flanges and Connecting-End Flanges of Valves and Fittings

Miscellaneous 1308.5.12

MSS SP-58-2009 Pipe Hangers and Supports-Materials, Design, Manufacture,Selection, Application, and Installation

Miscellaneous 1311.2.5

MSS SP-67-2002a* Butterfly Valves Valves 103.1, 306.1MSS SP-69-2003* Pipe Hangers and Supports-Selection and Application Miscellaneous 103.1, 306.1MSS SP-80-2008* Bronze Gate, Globe, Angle, and Check Valves Valves 103.1, 306.1

READ ONLY




MSS SP-89-2003* Pipe Hangers and Supports – Fabrication and InstallationPractices

Miscellaneous 103.1, 306.1

MSS SP-104-2003* Wrought Copper Solder Joint Pressure Fittings Fittings 103.1, 306.1MSS SP-106-2003* Cast Copper Alloy Flanges and Flanged Fittings: Class 125,

150 and 300 Fittings 103.1, 306.1

MSS SP-109-1997(R2006)*

Welded Fabricated Copper Solder Joint Pressure Fittings Fittings 103.1, 306.1

NEBB-2005 Procedural Standards for Testing Adjusting and Balancing ofEnvironmental Systems, 7th Edition

Balancing 317.1(4)

NFPA 10-2010* Portable Fire Extinguishers Fire Extinguishing 513.11, 513.11.2,517.7.4

NFPA 12-2011* Carbon Dioxide Extinguishing Systems Fire Extinguishing 513.2.2NFPA 13-2010* Installation of Sprinkler Systems Miscellaneous 513.2.2, 517.7.6NFPA 17-2009* Dry Chemical Extinguishing Systems Fire Extinguishing —NFPA 17A-2009* Wet Chemical Extinguishing Systems Fire Extinguishing 513.2.2, 513.3.2NFPA 30-2008* Flammable and Combustible Liquids Code Combustible Liquids,

Flammable Liquids 103.1, 306.1

NFPA 30A-2008* Motor Fuel Dispensing Facilities and Repair Garages Miscellaneous 911.8.1(2)NFPA 31-2011* Installation of Oil Burning Equipment Fuel Gas, Appliances 302.3, 1002.2.2,

1302.1, 1320.1,1333.1(2), 1334.6,1334.6.1, 1335.1,1336.2, 1336.3,E 502.6.1(2)

NFPA 37-2010* Installation and Use of Stationary Combustion Engines andGas Turbines

Generators 925.1, 1602.1

NFPA 52-2010* Vehicular Gaseous Fuel Systems Code CNG Vehicle FuelSystems

931.1

NFPA 54/Z223.1-2009* National Fuel Gas Code Fuel Gas 516.2.1, 1320.1,1329.1, 1335.1,1336.1, E 502.6.1(1)

NFPA 58-2011* Liquefied Petroleum Gas Code Fuel Gas 303.8, 516.2.1,1308.5.6.3,1308.5.11.4, 1315.1,1320.1, 1321.1,1322.1, 1327.1,1332.1, 1335.1,1336.1

NFPA 69-2008* Explosion Prevention Systems Explosion Prevention 103.1, 306.1NFPA 70-2011* National Electrical Code Miscellaneous 511.1.6, 512.2.5,

516.2.7, 516.2.9(4),602.2(5), 1311.13.5(2),1311.16

NFPA 80-2010* Fire Doors and Other Opening Protectives Fire Doors 510.7.4NFPA 82-2009* Incinerators and Waste and Linen Handling Systems and

Equipment Incinerator Chutes 918.1

NFPA 85-2011* Boiler and Combustion Systems Hazards Code Appliances 1001.1(9), 1002.1(3),1018.1, Table 1011.1

NFPA 88A-2011* Parking Structures Miscellaneous 911.8 NFPA 90A-2009* Installation of Air-Conditioning and Ventilating Systems HVAC 904.7

NFPA 90B-2009* Installation of Warm Air Heating and Air-ConditioningSystems

HVAC 103.1, 306.1

NFPA 91-2010* Exhaust Systems for Air Conveying of Vapors, Gases, Mists,and Noncombustible Particulate Solids

Product ConveyingDucts

103.1, 306.1

READ ONLY




NFPA 96-2011* Ventilation Control and Fire Protection of CommercialCooking Operations

Commercial Cooking 103.1, 306.1

NFPA 211-2010* Chimneys, Fireplaces, Vents, and Solid Fuel Burning Appli-ances

Fuel Gas Appliances 208.0, 517.7, 517.7.1,517.7.2, 801.2, 801.3,802.5.2, 802.5.3,802.5.7(2), 802.5.7(4),E 502.6.1(3)

NFPA 220-2009* Types of Building Construction Miscellaneous 904.1.2NFPA 221-2009* High Challenge Fire Walls, Fire Walls, and Fire Barrier Walls Building Fire Walls,

Fire Barrier208.0

NFPA 251-2011* Test of Fire Endurance of Building Construction and Mate-rials

Building 208.0

NFPA 259-2008* Potential Heat of Building Materials Testing, BuildingMaterials

214.0

NFPA 262-2011* Flame Travel and Smoke of Wires and Cables for Use in Air-Handling Spaces

Certification 602.2(5)

NFPA 274-2009* Test Method to Evaluate Fire Performance Characteristics ofPipe Insulation

Pipe Insulation 1201.3.2.11,1201.4.1.2

NFPA 409-2011* Aircraft Hangars Miscellaneous 911.9 NFPA 501A-2009* Fire Safety Criteria for Manufactured Home Installations,

Sites, and Communities Miscellaneous 103.1, 306.1

NFPA 654-2006* Prevention of Fire and Dust Explosions from the Manufac-turing, Processing, and Handling of Combustible ParticulateSolids

Dust ExplosionPrevention, Gutters

506.4

NFPA 780-2011* Installation of Lightning Protection Systems Fuel Gas 1311.14.4NFPA 853-2010* Installation of Stationary Fuel Cell Power Systems Fuel Cell Power

Plants, Fuel Cells 1601.1

PPI TR-4-2010* Listing for Hydrostatic Design Basis (HDB), Strength DesignBasis (SDB), Pressure Design Basis (PDB) and MinimumRequired Strength (MRS) Ratings for Thermoplastic PipingMaterials or Pipe

Certification 103.1, 306.1

SAE J512-1997 Automotive Tube Fittings Fittings 103.1, 306.1SMACNA-2002 HVAC Systems Testing, Adjusting and Balancing, 3rd

EditionBalancing 317.1(5)

SMACNA-2003 Fibrous Glass Duct Construction Standard, 7th Edition Fiberglass Ducts 103.1, 306.1SMACNA-2006* HVAC Duct Construction Standards Metal and Flexible, 3rd

EditionDucts, Metal andFlexible

506.2(1), 602.1,602.4, 602.5, 602.6,603.2, 603.2.1, 603.5,604.1, E 503.4.4, E 503.4.4.2

UL 17-2008 Vent or Chimney Connector Dampers for Oil-Fired Appli-ances (with revisions through January 27, 2010)

Vent Dampers 103.1, 306.1

UL 21-2007* LP-Gas Hose (with revisions through April 26, 2010) Hose, LPG Hose 103.1, 306.1UL 33-2010* Heat Responsive Links for Fire-Protection Service Fusible Links 103.1, 306.1UL 51-2002 Power-Operated Pumps for Anhydrous Ammonia and LP-Gas

(with revisions through April 13, 2010)Ammonia Pumps,LPG Pumps, Pumps

103.1, 306.1

UL 80-2007* Steel Tanks for Oil-Burner Fuels and Other CombustibleLiquids (with revisions through August 26, 2009)

Fuel Gas 1334.6.2

UL 103-2010* Factory-Built Chimneys for Residential Type and BuildingHeating Appliances


UL 125-2009* Flow Control Valves for Anhydrous Ammonia and LP-Gas(with revisions through February 26, 2010)

Fuel Gas 103.1, 306.1

UL 127-2008* Factory-Built Fireplaces (with revisions through December 3,2009)

Fireplaces 103.1, 306.1

READ ONLY




UL 132-2007* Safety Relief Valves for Anhydrous Ammonia and LP-Gas(with revisions through July 23, 2010)

Fuel Gas 103.1, 306.1

UL 144-1999* LP-Gas Regulators (with revisions throughAugust 27, 2010) Fuel Gas 103.1, 306.1UL 174-2004* Household Electric Storage Tank Water Heaters (with revi-

sions through April 22, 2009)Appliances 103.1, 306.1

UL 180-2003* Liquid-Level Indicating Gauges for Oil Burner Fuels (withrevisions through March 2, 2007)

Gauges, Level Gauges 103.1, 306.1

UL 181-2005* Factory-Made Air Ducts and Air Connectors (with revisionsthrough October 27, 2008)

Air connectors, Airducts

602.5

UL 181A-2005* Closure Systems for Use with Rigid Air Ducts (with revisionsthrough February 13, 2008)

Air Ducts 602.4, Table E 503.4.4.2(2)

UL 181B-2005* Closure Systems for Use with Flexible Air Ducts and AirConnectors (with revisions through February 13, 2008)

Air Connectors, Airducts

602.4, Table E 503.4.4.2(2)

UL 197-2010* Commercial Electric Cooking Appliances Appliances, Commer-cial Cooking, ElectricAppliances

103.1, 306.1

UL 207-2009* Refrigerant-Containing Components and Accessories,Nonelectrical

Refrigeration Compo-nents

103.1, 306.1

UL 252-2010* Compressed Gas Regulators Fuel Gas 103.1, 306.1UL 268A-2008* Smoke Detectors for Duct Application (with revisions

through September 25, 2009)Smoke Detectors 103.1, 306.1

UL 296-2003* Oil Burners (with revisions through March 5, 2010) Fuel Gas, Appliances 103.1, 306.1UL 300-2005* Fire Testing of Fire Extinguishing Systems for Protection of

Commercial Cooking Equipment (with revisions throughJuly 16, 2010)

Certification 513.2.2, 513.2.5

UL 343-2008 Pumps for Oil-Burning Appliances Fuel Gas, Appliances 103.1, 306.1UL 352-2006 Constant-Level Oil Valves (with revisions through March 16,

2010)Fuel Gas 103.1, 306.1

UL 353-1994 Limit Controls (with revisions through September 30, 2010) Controls 103.1, 306.1

UL 378-2006 Draft Equipment (with revisions through January 27, 2010) Fuel Gas, Appliances 103.1, 306.1UL 391-2010* Solid-Fuel and Combination-Fuel Central and Supplementary

Furnaces Furnaces, Solid Fuel 103.1, 306.1

UL 399-2008* Drinking Water Coolers (with revisions through December15, 2009)

Appliances 103.1, 306.1

UL 404-2010* Gauges, Indicating Pressure for Compressed Gas Service Fuel Gas 103.1, 306.1UL 412-2004* Refrigeration Unit Coolers (with revisions through January 8,

2009)Refrigeration 103.1, 306.1

UL 429-2009 Electrically Operated Valves (with revisions through January6, 2010)

Valves 103.1, 306.1

UL 441-2010* Gas Vents (with revisions through May 18, 2010) Fuel Gas 103.1, 306.1UL 443-2006* Steel Auxiliary Tanks for Oil-Burner Fuel (with revisions

through March 25, 2008)Fuel Gas 103.1, 306.1

UL 471-2010* Commercial Refrigerators and Freezers Freezers, Refrigerators 103.1, 306.1

UL 525-2008* Flame Arresters Flame Arrestors 103.1, 306.1UL 536-1997* Flexible Metallic Hose (with revisions through June 9, 2003) Fuel Gas 103.1, 306.1

UL 555-2006* Fire Dampers (with revisions through May 4, 2010) Dampers 103.1, 306.1UL 555C-2006* Ceiling Dampers (with revisions through May 4, 2010) Dampers 103.1, 306.1UL 555S-1999* Smoke Dampers (with revisions through May 4, 2010) Dampers 103.1, 306.1UL 565-1998 Liquid-Level Gauges and Indicators for Anhydrous Ammonia

and LP-Gas (with revisions through June 1, 2001)Fuel Gas 103.1, 306.1

READ ONLY




UL 569-1995* Pigtails and Flexible Hose Connectors for LP-Gas (with revi-sions through November 3, 2009)

Fuel Gas 103.1, 306.1

UL 641-2010* Type L Low-Temperature Venting Systems Equipment 103.1, 306.1UL 651-2005 Schedule 40 and Rigid PVC Conduit and Fittings (with revi-

sions through March 11, 2010)Piping, Plastic 1308.5.5

UL 710-1995 Exhaust Hoods for Commercial Cooking Equipment (withrevisions through June 29, 2010)

Exhaust Hoods,Hoods

508.6

UL 710B-2004* Recirculating Systems (with revisions through June 29, 2010) Exhaust Hoods 508.1(2), 513.2.2,516.2.2

UL 723-2008* Test for Surface Burning Characteristics of Building Mate-rials (with revisions through September 13, 2010)

Miscellaneous 508.2.8, 508.3, 602.2,604.1, 1201.3.2.11,1201.4.1.2,Table 303.4

UL 726-1995 Oil-Fired Boiler Assemblies (with revisions throughApril 22,2010)

Fuel Gas, Appliances 1002.2.1

UL 727-2006 Oil-Fired Central Furnaces (with revisions throughApril 22,2010)

Fuel Gas, Appliances Table E 503.7.1(5)

UL 729-2003* Oil-Fired Floor Furnaces (with revisions throughApril 22,2010)

Furnaces, Floor, OilFired Furnaces

103.1, 306.1

UL 730-2003* Oil-Fired Wall Furnaces (with revisions throughApril 22,2010)

Furnaces, Wall, OilFired

103.1, 306.1

UL 731-1995* Oil-Fired Unit Heaters (with revisions throughApril 22,2010)

Heaters, Oil Fired Table E 503.7.1(5)

UL 732-1995* Oil-Fired Storage Tank Water Heaters (with revisions throughApril 22, 2010)


UL 733-1993 Oil-Fired Air Heaters and Direct-Fired Heaters (with revi-sions throughApril 22, 2010)

Water Heaters, DirectFired, Oil Fired

103.1, 306.1

UL 737-2007* Fireplace Stoves (with revisions through January 27, 2010) Fireplace Stoves 103.1, 306.1

UL 791-2006 Residential Incinerators (with revisions through April 29,2010)

Incinerators 103.1, 306.1

UL 795-2006 Commercial-Industrial Gas Heating Equipment (with revi-sions throughApril 29, 2010)

Heating Equipment,Gas Fired

103.1, 306.1

UL 834-2004* Heating, Water Supply, and Power Boilers-Electric (withrevisions through December 4, 2009)

Appliances 1002.3

UL 842-2007* Valves for Flammable Fluids (with revisions through July 12,2010)

Valves 103.1, 306.1

UL 858-2005* Household Electric Ranges (with revisions throughAugust18, 2010)

Electric Ranges,Ranges

103.1, 306.1

UL 867-2000* Electrostatic Air Cleaners (with revisions through February12, 2010)

Filters 103.1, 306.1

UL 896-1993* Oil-Burning Stoves (with revisions through May 7, 2010) Stoves, Oil Fired 103.1, 306.1UL 900-2004* Air Filter Units (with revisions through November 6, 2009) Air Filters, Filters 103.1, 306.1UL 907-2010* Fireplace Accessories (with revisions throughApril 6, 2010) Fireplace Accessories 103.1, 306.1UL 921-2006* Commercial Dishwashers (with revisions through June 23,

2010)Appliances 103.1, 306.1

UL 959-2010* Medium Heat Appliance Factory-Built Chimneys Fuel Gas, Appliances 103.1, 306.1UL 984-1996 Hermetic Refrigerant Motor-Compressors (with revisions

through September 23, 2005)Compressors, Refrig-eration

103.1, 306.1

UL 1026-2007* Electric Household Cooking and Food Serving Appliances(with revisions through June 16, 2010)

Cooking Appliances,Electric Appliances

103.1, 306.1

UL 1046-2010 Grease Filters for Exhaust Ducts (with revisions throughFebruary 11, 2010)

Filters-Grease 509.1

READ ONLY




UL 1206-2003* Electric Commercial Clothes-Washing Equipment (with revi-sions through June 16, 2010)


UL 1240-2005* Electric Commercial Clothes-Drying Equipment (with revi-sions through June 16, 2010)

Clothes Dryers,Commercial

103.1, 306.1

UL 1453-2004* Electric Booster and Commercial Storage Tank Water Heaters(with revisions through December 4, 2009)


UL 1479-2003* Fire Tests of Through-Penetration Firestops (with revisionsthrough March 1, 2010)

Miscellaneous 507.2.4, 507.2.5

UL 1482-2010* Solid-Fuel Type Room Heaters (with revisions throughOctober 8, 2010)

Room Heaters, SolidFuel Heaters

103.1, 306.1

UL 1738-2010* Venting Systems for Gas-Burning Appliances, Categories II,III, and IV

Gas Vent Systems,Vent Systems

103.1, 306.1

UL 1746-2007* External Corrosion Protection Systems for Steel Under-ground Storage Tanks

Tanks 103.1, 306.1

UL 1777-2007* Chimney Liners (with revisions through July 3, 2009) Chimneys, Liners 803.1.12.2UL 1812-2009 Ducted Heat Recovery Ventilators (with revisions through

June 11, 2010)Heat Recovery Venti-lators

103.1, 306.1

UL 1815-2009 Nonducted Heat Recovery Ventilators (with revisionsthrough November 12, 2010)

Heat Recovery Venti-lators

103.1, 306.1

UL 1820-2004* Fire Test of Pneumatic Tubing for Flame and Smoke Charac-teristics (with revisions through February 16, 2009)

Surface Burning Test,Pneumatic Tubing

602.2(7)

UL 1887-2004* Fire Test of Plastic Sprinkler Pipe for Visible Flame and SmokeCharacteristics (with revisions through February 16, 2009)

Surface Burning Test,Fire Sprinkler Pipe

602.2(6)

UL 1963-2005* Refrigerant Recovery/Recycling Equipment (with revisionsthrough June 30, 2010)

Refrigerant Equip-ment

103.1, 306.1

UL 1978-2010* Grease Ducts Ducts, Grease 508.2.11UL 1995-2005 Heating and Cooling Equipment (with revisions through July

30, 2009)HVAC, Electric 103.1, 306.1

UL 2021-1997 Fixed and Location-Dedicated Electric Room Heaters (withrevisions through June 30, 2010)

Product, Heating,Electric

103.1, 306.1

UL 2043-2008 Fire Test for Heat and Visible Smoke Release For DiscreteProducts and Their Accessories Installed in Air-HandlingSpaces

Surface Burning Test,Discrete Products

602.2(8)

UL 2157-1997* Electrical Clothes Washing Machines and Extractors (withrevisions through February 16, 2010)


UL 2158-1997* Electric Clothes Dryers (with revisions through March 20,2009)

Clothes Dryers, Elec-tric

103.1, 306.1

UL 2200-1998* Stationary Engine Generator Assemblies (with revisionsthrough December 22, 2009)

Assemblies 1602.1

UL 2221-2010 Tests of Fire Resistive Grease Duct Enclosure Assemblies Duct Wrap, GreaseDuct Enclosure

507.2.4

* ANSI designated as an American National Standard.Italic/Bold referenced standards indicate where such standards are located in the narrative of the code.Notes:1 Although these standards are referenced in Chapter 17, some of the materials and equipment in the standards are not acceptable for use under the provi-sions of this code.

2 See Section 1201.3.3.2 for restrictions.

READ ONLY



ABBREVIATIONS IN TABLE 1701.0

AABC Associated Air Balance Council, 1518 K St. NW, Suite 503 Washington, DC 20005.ACCA Air Conditioning Contractors of America Association, Inc., 2800 Shirlington Road, Suite 300, Arlington, VA 22206.AMCA Air Movement and Control Association, 30 West University Dr. Arlington Heights, IL 60004-1806.ANSI American National Standards Institute, Inc., 25 W. 43rd Street, 4th Floor, New York, NY 10036.AHRI Air-Conditioning, Heating, and Refrigeration Institute, 2111 Wilson Blvd., Suite 500, Arlington, VA 22201.ASCE American Society of Civil Engineers, 1801 Alexander Bell Drive, Reston, VA 20191-4400.ASHRAE American Society of Heating, Refrigerating, and Air Conditioning Engineers, Inc., 1791 Tullie Circle, NE,

Atlanta, GA 30329-2305.ASME American Society of Mechanical Engineers, Three Park Avenue, New York, NY 10016-5990.ASTM American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.AWS American Welding Society, 550 N.W. LeJeune Road, Miami, FL, 33126.AWWA American Water Works Association, 6666 W. Quincy Ave., Denver, CO 80235.CGSB Canadian General Standards Board, 11 Laurier Street Phase III, Place du Portage, 6B1, Gatineau, Quebec,

Canada K1A 0S5.CGA Compressed Gas Association, 1401 George Carter Way, Suite 103, Chantilly, VA 20151.CSA Canadian Standards Association, 5060 Spectrum Way, Suite 100, Mississauga, Ontario, Canada, L4W 5N6.EPA Environmental Protection Agency, 1200 Pennsylvania Ave., N.W., Washington, DC 20460.IAPMO International Association of Plumbing and Mechanical Officials, 5001 E. Philadelphia Street, Ontario, CA

91761.IAS International Approval Services, A Division of CSA, 8501 East Pleasant Valley Road Cleveland, OH 44131.I-B-R Institute of Boiler and Radiator Manufacturers, 35 Russo Place, Berkeley Heights, NJ 07922.ILAR International Institute of Ammonia Refrigeration, 1110 North Glebe Road, Arlington, VA 22201.ISO International Organization for Standardization, 1 ch. de la Voie-Creuse, Casa Postale 56, CH-1211 Geneva 20,

Switzerland.MSS Manufacturers Standardization Society of the Valve and Fitting Industry, 127 Park Street NE, Vienna, VA 22180.NEBB National Environmental Balancing Bureau (NEBB) 8575 Grovemont Circle, Gaithersburg, MD 20877.NFPA National Fire Protection Association, 1 Batterymarch Park, P.O. Box 9101, Quincy, MA 02169-9101.PPI Plastic Pipe Institute, 105 Recker Court, Suite 825, Irving, TX 75062.SAE Society of Automotive Engineers, 400 Commonwealth Drive, Warrendale, PA 15096.SMACNA Sheet Metal and Air Conditioning Contractors National Association, 4201 Lafayette Center Drive, Chantilly,

VA 20151-1209.UL Underwriters Laboratories, Inc., 333 Pfingsten Road, Northbrook, IL 60062.

READ ONLY


READ ONLY

Documents

X X X X X X X X X X ONLY READ - IAPMO Group California Mechanical Code/Chapter 17.pdf · 2013 CALIFORNIA MECHANICAL CODE 301 ... 6th Edition Balancing 317.1 ... Rules for Construction